INCH-POUND MIL-DTL-83723/72E 19 August 2009 SUPERSEDING MIL-DTL-83723/72D 15 September 2006 DETAIL SPECIFICATION SHEET CONNECTOR, ELECTRIC, (CIRCULAR, ENVIRONMENT RESISTING), RECEPTACLE, (FLANGE MOUNT, BAYONET COUPLING, CRIMP PIN CONTACT) (SERIES III, CLASSES A, G, M, R, T, W AND Z) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83723. FIGURE 1. Dimensions and configurations. AMSC N/A FSC 5935 MIL-DTL-83723/72E FIGURE 1. Dimensions and configurations - Continued. 2 MIL-DTL-83723/72E Shell size A 8 .120 10 .120 12 .120 14 .120 16 .120 18 .120 20 .120 22 .120 24 .149 C .428 .433 .530 .535 .700 .705 .769 .774 .869 .901 1.002 1.007 1.127 1.132 1.252 1.257 1.377 1.382 D max .312 .388 .558 .627 .772 .860 .985 1.110 1.235 F .536 .531 .659 .654 .829 .824 .898 .893 1.025 1.020 1.131 1.126 1.256 1.251 1.381 1.376 1.506 1.501 J max K L S +.005 -.000 .561 .594 .812 .508 .696 .719 .937 .636 .875 .812 1.031 .806 .935 .906 1.125 .875 1.062 .969 1.250 1.002 1.187 1.062 1.343 1.108 1.312 1.156 1.437 1.233 1.437 1.250 1.562 1.358 1.562 1.375 1.703 1.483 FIGURE 1. Dimensions and configurations - Continued. 3 MIL-DTL-83723/72E Inches .0025 .005 .008 .015 .018 .020 .022 .032 .042 .046 .052 .065 .069 .071 .072 .076 .084 .089 .090 .094 .097 .101 .106 .112 mm 0.06 0.13 0.20 0.38 0.46 0.51 0.56 0.81 1.07 1.17 1.32 1.65 1.75 1.80 1.83 1.93 2.13 2.26 2.29 2.39 2.46 2.57 2.69 2.84 Inches .120 .125 .138 .144 .149 .198 .204 .211 .250 .259 .312 .366 .376 .378 .380 .388 .392 .428 .433 .490 .508 .530 .531 .535 mm 3.05 3.18 3.51 3.66 3.78 5.03 5.18 5.36 6.35 6.58 7.92 9.30 9.55 9.60 9.65 9.86 9.96 10.87 11.00 12.45 12.90 13.46 13.49 13.59 Inches .536 .540 .558 .560 .561 .594 .627 .636 .654 .659 .696 .700 .705 .708 .719 .728 .769 .772 .774 .806 .812 .824 .829 .860 mm 13.61 13.72 14.17 14.22 14.25 15.09 15.93 16.15 16.61 16.74 17.68 17.78 17.91 17.98 18.26 19.49 19.53 19.61 19.66 20.47 20.62 20.93 21.06 21.84 Inches .875 .893 .896 .898 .901 .906 .935 .937 .969 .985 1.002 1.007 1.020 1.025 1.062 1.070 1.108 1.125 1.126 1.127 1.131 1.132 1.156 1.187 mm 22.23 22.68 22.76 22.81 22.89 23.01 23.75 23.80 24.61 25.02 25.45 25.58 25.91 26.04 26.97 27.18 28.14 28.58 28.60 28.63 28.73 28.75 29.36 30.15 Inches 1.233 1.235 1.250 1.251 1.252 1.256 1.257 1.312 1.343 1.375 1.376 1.377 1.381 1.382 1.385 1.437 1.483 1.501 1.506 1.562 1.703 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm) for three place decimals, .01 (0.25 mm) for two place decimals and 1 for all angles. 4. Rear accessory interchangeability dimensions shall be accordance with SAE-AS85049. 5. The centerline of indicated projection must be located on vertical centerline 2. 6. See table I for contact cavities requiring this dimension. FIGURE 1. Dimensions and configurations - Continued. 4 mm 31.32 31.37 31.75 31.78 31.80 31.90 31.93 33.32 34.11 34.93 34.95 34.98 35.08 35.10 35.18 36.50 37.66 38.13 38.25 39.67 43.26 MIL-DTL-83723/72E REQUIREMENTS: Dimensions and configuration: See figure 1. For insert arrangements, see MIL-STD-1554 and table I. TABLE I. Inserts requiring reduced diameters for raised seal barriers on contact cavities. Shell size 8 10 Insert arrangements 03 06 Contact cavities 1, 2, and 3 1, 2, 3, 4, 5, 6 For connector accessories: See SAE-AS85049. This connector mates with MIL-DTL-83723/75 and /77. Part or Identifying Number (PIN) example: M83723/ 72 W 22 55 N Military designation Specification sheet number Class Shell size Insert arrangement Polarizing position Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-83723, this document references the following: MIL-DTL-83723/75 MIL-DTL-83723/77 MIL-STD-1554 SAE-AS85049 5 MIL-DTL-83723/72E CONCLUDING MATERIAL Custodians: Army - CR Navy - AS Air Force - 85 DLA - CC Preparing activity: DLA - CC (Project 5935-2008-126) Review activities: Army - AR, MI Navy - EC Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil. 6