HDSP-52xE Series HDSP-52xG Series HDSP-52xY Series 14.2 mm (0.56 inch) General Purpose Two Digit Seven Segment Displays Data Sheet Description Features These 14.2 mm (0.56 inch) two digit displays use industry standard size and pin-out. The devices are available as either common anode or common cathode. These gray-faced displays are available in a choice of high efficiency red (HER), green, or yellow colors. The HDSP-521x and HDSP-523x series are suitable for indoor use. * Industry standard size * Industry standard pin-out 15.24 mm (0.6 in.) DIP leads on 2.54 mm (0.1 in.) centers * Choice of colors Red, green, yellow * Mitered font Mitered corners on segments * Gray face paint Gray package gives optimum contrast * 50 viewing angle * Design flexibility Common anode or common cathode * Categorized for luminous intensity * Green and yellow categorized for color These parts are subjected to Outgoing Quality Assurance (OQA) inspection with AQL of 0.065% for functional and visual/cosmetic rejects. Applications * Suitable for indoor use * Not recommended for industrial applications, i.e. operating temperatures requirements exceeding 85C or below -35C[1] * Extreme temperature cycling not recommended[2] Devices HER HDSP521E 523E Green HDSP521G 523G Yellow HDSP521Y 523Y Description Common Anode Right Hand Decimal Common Cathode Right Hand Decimal Notes: 1. For industrial applications, it is recommended to use HDSP-5521/5523/5621/5623/5721/5723. 2. For details, please contact your local Avago sales office or an authorized distributor. Part Numbering System 5082 -X X X X-X X X X X HDSP-X X X X-X X X X X Mechanical Options[1] 00: No Mechanical Option Color Bin Options[1,2] 0: No Color Bin Limitation Maximum Intensity Bin[1,2] 0: No Maximum Intensity Bin Limitation Minimum Intensity Bin[1,2] 0: No Minimum Intensity Bin Limitation Device Configuration/Color[1] E: High Efficiency Red G: Green Y: Yellow Device Specific Configuration[1] Refer to Respective Datasheet Package[1] Refer to Respective Datasheet Notes: 1. For codes not listed in the figure above, please refer to the respective datasheet or contact your nearest Avago representative for details. 2. Bin options refer to shippable bins for a part number. Color and Intensity Bins are typically restricted to 1 bin per tube (exceptions may apply). Please refer to respective datasheet for specific bin limit information. 2 Package Dimensions TOP END VIEW 2.54 (0.100) HDSP-XXXX YWW XZ COO COUNTRY OF ORIGIN COLOR BINNING (NOTE 3) 2.34 (0.092) DATE CODE 4.27 0.50 (0.168 0.020) 7.80 (0.307) 8.00 (0.315) 10 18 17 16 15 14 13 12 11 10 14.22 (0.560) 18.60 (0.732) 1 DIGIT NO. 1 2 3 4 5 6 7 8 6.86 (0.270) 4.81 (0.191) SIDE VIEW 6.150 (0.242) 25.00 (0.984) FRONT VIEW NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES). 2. TOLERANCE IS 0.25 mm (0.01 INCH) UNLESS OTHERWISE STATED. 3. FOR GREEN AND YELLOW ONLY. 3 15.24 (0.600) 9 12.70 (0.500) 0.50 DIA. (0.020) LUMINOUS INTENSITY CATEGORY Internal Circuit Diagram 18 17 16 15 14 13 12 11 10 COMMON ANODE a a PIN f b b f g g c e c d e d DP 1 2 3 4 DP 5 6 7 8 9 COMMON ANODE 18 17 16 15 14 13 12 11 10 a a f b b f g g c e c d e d DP 1 2 3 4 DP 5 6 7 COMMON CATHODE 4 8 9 FUNCTION COMMON CATHODE PIN FUNCTION 1 E CATHODE NO. 1 1 E ANODE NO. 1 2 3 D CATHODE NO. 1 C CATHODE NO. 1 2 3 D ANODE NO. 1 C ANODE NO. 1 4 DP CATHODE NO. 1 4 DP ANODE NO. 1 5 6 E CATHODE NO. 2 D CATHODE NO. 2 5 6 E ANODE NO. 2 D ANODE NO. 2 7 G CATHODE NO. 2 7 G ANODE NO. 2 8 9 C CATHODE NO. 2 DP CATHODE NO. 2 8 9 C ANODE NO. 2 DP ANODE NO. 2 10 B CATHODE NO. 2 10 B ANODE NO. 2 11 12 A CATHODE NO. 2 F CATHODE NO. 2 11 12 A ANODE NO. 2 F ANODE NO. 2 13 14 DIGIT NO. 2 ANODE DIGIT NO. 1 ANODE 13 14 DIGIT NO. 2 CATHODE DIGIT NO. 1 CATHODE 15 16 B CATHODE NO. 1 A CATHODE NO. 1 15 16 B ANODE NO. 1 A ANODE NO. 1 17 G CATHODE NO. 1 17 G ANODE NO. 1 18 F CATHODE NO. 1 18 F ANODE NO. 1 Absolute Maximum Ratings at TA=25C Parameter Average Power per Segment or DP Peak Forward Current per Segment or DP (1/10 Duty Cycle, 0.1 ms Pulse Width) DC Forward Current per Segment or DP[1] Reverse Voltage per Segment or DP Operating Temperature Storage Temperature Wave Soldering Temperature for 3 seconds[4] (2 mm [0.063 in.] below Body) HER HDSP-521E HDSP-523E 62.5 90 Green HDSP-521G HDSP-523G 105 90 Yellow HDSP-521Y HDSP-523Y 45 60 Units mW mA 25[1] 5 -35 to +85 -35 to +85 250 30[3] 5 -35 to +85 -35 to +85 250 20[2] 5 -35 to +85 -35 to +85 250 mA V C C C Notes: 1. Derate above 25C at 0.33 mA/C. 2. Derate above 25C at 0.27 mA/C. 3. Derate above 40 celcius at 0.35 mA/celcius. 4. Not recommended to be soldered more than 2 times. Minimum interval between solderings is 15 minutes. Total soldering time not to exceed 5 seconds. Optical/Electrical Characteristics at TA=25C High Efficiency Red Devices HDSP- 521E 523E Symbol Iv Parameter Symbol Min. Typ. Max. Units Test Conditions Luminous Intensity/Segment (Segment Average)[1,2] Forward Voltage/Segment or DP Peak Wavelength Dominant Wavelength[3] Reverse Voltage/Segment or DP[4] Temperature Coefficient of VF/Segment or DP Iv 2.28 3.50 5.13 mcd IF = 10 mA 2.0 568 570 2.4 V nm nm V mV/C IF = 10 mA VF PEAK d VR VF/C Min. 2.28 Typ. 4.00 Max. 7.69 Units mcd 2.05 640 628 2.60 V nm nm V mV/C Test Conditions IF = 10 mA Parameter Luminous Intensity/Segment (Segment Average)[1,2] Forward Voltage/Segment or DP Peak Wavelength Dominant Wavelength[3] Reverse Voltage/Segment or DP[4] Temperature Coefficient of VF/Segment or DP 5.0 -2 IF = 20 mA IF = 10 mA IR = 100 A Green Devices HDSP- 521G 523G 5 VF PEAK d VR VF/C 564.5 5.0 -2 576.5 IF = 10 mA IR = 100 A Yellow Devices HDSP- 521Y 523Y Parameter Symbol Min. Typ. Max. Units Test Conditions Luminous Intensity/Segment (Segment Average)[1,2] Iv 1.52 2.30 5.13 mcd IF = 10 mA Forward Voltage/Segment or DP VF 2.1 2.4 V IF = 20 mA Peak Wavelength PEAK 589 Dominant Wavelength[3] Reverse Voltage/Segment or DP[4] d 582.0 VR 5.0 VF/C Temperature Coefficient of VF/Segment or DP 587 -2 nm 592.0 nm IF = 10 mA V IR = 100 A mV/C Notes: 1. Case temperature of the device immediately prior to the intensity measurement is 25C. 2. The digits are categorized for luminous intensity. The intensity category is designated by a letter on the side of the package. 3. The dominant wavelength, d, is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 4. Typical specification for reference only. Do not exceed absolute maximum ratings. Intensity Bin Limits[1] (mcd at 10 mA) Yellow Bin Name F G H I Min.[2] 1.52 2.28 3.42 NA Green Max.[2] 2.28 3.42 5.13 NA Min.[2] NA 2.28 3.42 NA HER Max.[2] NA 3.42 5.13 NA Notes: 1. Bin categories are established for classification of products. Products may not be available in all bin categories. 2. Tolerance for each bin limit is 10%. Color Categories (Dominant Wavelength) Green Bin Name 3 2 Min.[2] Bin Name 2 3 Min.[2] Max.[2] 573.5 576.5 570.5 573.5 Yellow 587.00 584.50 Max.[2] 589.50 587.00 Notes: 1. Bin categories are established for classification of products. Products may not be available in all bin categories. 2. Tolerance for each bin limit is 1 nM. 6 Min.[2] NA 2.28 3.42 5.13 Max.[2] NA 3.42 5.13 7.69 30 25 20 GREEN / HER 15 YELLOW 10 5 0 20 30 40 50 60 70 80 90 100 TA - AMBIENT TEMPERATURE - C Figure 1. Maximum allowable DC current vs. ambient temperature. RELATIVE LUMINOUS INTENSITY (NORMALIZED AT 10 mA) 3.5 3.0 2.5 2.0 HER, YELLOW, GREEN 1.0 0.5 0 0 5 10 15 20 25 30 35 IF - DC FORWARD CURRENT - mA Figure 3. Relative luminous intensity vs. DC forward current. 7 Contrast Enhancement GREEN 80 For information on contrast enhancement, please see Application Note 1015. 70 60 YELLOW 50 40 Soldering/Cleaning 30 HER 20 10 0 1 2 3 5 4 VF - FORWARD VOLTAGE - V Figure 2. Forward current vs. forward voltage. 4.0 1.5 IF - FORWARD CURRENT PER SEGMENT - mA 35 90 40 V - RELATIVE EFFICIENCY (NORMALIZED TO 1 AT 10 mA PER SEGMENT) IDC - MAXIMUM DC CURRENT PER SEGMENT - mA 40 1.6 1.5 1.4 YELLOW HER 1.3 1.2 For information on soldering LEDs please refer to Application Note 1027. GREEN Device Reliability 1.1 1.0 0.9 0.8 0.7 0.6 Cleaning agents from the ketone family (acetone, methyl ethyl ketone, etc.) and from the chlorinated hydrocarbon family (methylene chloride, trichloroethylene, carbon tetrachloride, etc.) are not recommended for cleaning LED parts. All of these various solvents attack or dissolve the encapsulating epoxies used to form the package of plastic LED parts. 0 10 20 30 40 50 60 70 80 90 100 IPEAK - PEAK FORWARD CURRENT PER SEGMENT - mA Figure 4. Relative efficiency (luminous intensity per unit current) vs. peak current. For reliability information, please see the reliability data sheet 14.2 mm (0.56 inch) General Purpose Two Digit Seven Segment Display. For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Pte. in the United States and other countries. Data subject to change. Copyright (c) 2006 Avago Technologies Pte. All rights reserved. Obsoletes 5988-0376EN 5988-5378EN May 9, 2006