Product Specification
PS011706-0511
Z80C30/Z85C30
CMOS SCC Serial
Communications
Controller
Copyright ©2011 Zilog®, Inc. All rights reserved.
www.zilog.com
PS011706-0511
CMOS SCC Serial Communications Controller
Product Specification
ii
DO NOT USE THIS PRODUCT IN LIFE SUPPORT SYSTEMS.
LIFE SUPPORT POLICY
ZILOG’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE
SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF
THE PRESIDENT AND GENERAL COUNSEL OF ZILOG CORPORATION.
As used herein
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b)
support or sustain life and whose failure to perform when properly used in accordance with instructions for
use provided in the labeling can be reasonably expected to result in a significant injury to the user. A criti-
cal compon ent is a ny comp onent in a life su pport dev ice or s ystem wh ose failu re to pe rform can be reason -
ably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
Document Disclaimer
©201 1 Zilog, Inc. All rights reserved. Information in this publication concer ning the devices, applications,
or technology described is intended to suggest possible uses and may be superseded. Zilog, INC. DOES
NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF THE
INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. Zilog ALSO
DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT RELATED
IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED
HEREIN OR OTHERWISE. The information contained within this document has been verified according
to the general principles of electrical and mechanical engineering.
Z8 is a registered trademark of Zilog, Inc. All other product or service names are the property of their
respective owners.
Warning:
PS011706-0511 Revision History
CMOS SCC Serial Communications Controller
Product Specification
iii
Revision History
Each instance in Revision History reflects a change to this document from its previous
revision. For more details, refer to the corresponding pages and appropriate links in the
table below.
Date Revision
Level Description Page No
May
2011 06 Corrected Ordering Information section to reflect lead-free parts; updated
logo and style to conform to current template. 72, all
Jun
2008 05 Updated Zilog logo, Zilog Text, Disclaimer as per latest template. All
Sep
2004 01 Original issue All
PS011706-0511 Table of Contents
CMOS SCC Serial Communications Controller
Product Specification
iv
Table of Contents
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Other Features for Z85C30 Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
CTSA, CTSB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DCDA, DCDB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DTR/REQA, DTR/REQB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
IEI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
IEO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
INT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
INTACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PCLK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
RxDA, RxDB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
RTxCA, RTxCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
RTSA, RTSB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SYNCA, SYNCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
TxDA, TxDB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TRxCA, TRxCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
W/REQA, W/REQB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Z85C30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
A/B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
D7–D0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
D/C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
RD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
WR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Z80C30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
AD7–AD0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
AS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
CS0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
CS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PS011706-0511 Table of Contents
CMOS SCC Serial Communications Controller
Product Specification
v
DS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
R/W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Pin Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Functional Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
I/O Interface Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Polling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
CPU/DMA Block Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SCC Data Communications Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Asynchronous Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Synchronous Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Baud Rate Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Digital Phase-Locked Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Data Encoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Auto Echo and Local Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
SDLC FIFO Frame Status FIFO Enhancement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Z85C30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Z80C30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Z85C30/Z80C30 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Z85C30 Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Z80C30 Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Standard Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Part Number Suffix Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
PS011706-0511 List of Figures
CMOS SCC Serial Communications Controller
Product Specification
vi
List of Figures
Figure 1. SCC Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Figure 2. Z85C30 and Z80C30 DIP Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 3. Z85C30 and Z80C30 PLCC Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 4. Z85C30 Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 5. Z80C30 Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 6. SCC Transmit Data Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 7. SCC Receive Data Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 8. SCC Interrupt Priority Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 9. SCC Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 10. Detecting 5- or 7-Bit Synchronous Characters . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 11. An SDLC Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 12. Data Encoding Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 13. SDLC Frame Status FIFO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 14. SDLC Byte Counting Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 15. Write Register Bit Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 16. Write Register Bit Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 17. Write Register Bit Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 18. Write Register Bit Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 19. Read Register Bit Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 20. Read Register Bit Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 21. Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 22. Write Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 23. Interrupt Acknowledge Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 24. Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 25. Write Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 26. Interrupt Acknowledge Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 27. Standard Test Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 28. Open-Drain Test Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
PS011706-0511 List of Figures
CMOS SCC Serial Communications Controller
Product Specification
vii
Figure 29. Z85C30 Read/Write Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Figure 30. Z85C30 Interrupt Acknowledge Timing Diagram . . . . . . . . . . . . . . . . . . . . . 49
Figure 31. Z85C30 Cycle Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Figure 32. Z85C30 Reset Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Figure 33. Z85C30 General Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Figure 34. Z85C30 System Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Figure 35. Z80C30 Read/Write Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Figure 36. Z80C30 Interrupt Acknowledge Timing Diagram . . . . . . . . . . . . . . . . . . . . . 62
Figure 37. Z80C30 Reset Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Figure 38. Z80C30 General Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Figure 39. Z80C30 System Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Figure 40. 40-Pin DIP Package Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Figure 41. 44-Pin PLCC Package Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
PS011706-0511 List of Tables
CMOS SCC Serial Communications Controller
Product Specification
viii
List of Tables
Table 1. SCC Read Register Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Table 2. SCC Write Register Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Table 3. Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table 4. Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table 5. Z80C30/Z85C30 DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table 6. Z85C30 Read/Write Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Table 7. Z85C30 General Timing Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Table 8. Z85C30 System Timing Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Table 9. Z85C30 Read/Write Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Table 10. Z80C30 Read/Write Timing1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Table 11. Z80C30 General Timing1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Table 12. Z80C30 System Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Table 13. Z80C30/Z85C30 Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
PS011706-0511 Overview
CMOS SCC Serial Communications Controller
Product Specification
1
Overview
The features of Zilog’s Z80C30 and Z85C30 devices include:
Z85C30: optimized for nonmultiplexed bus microprocessors
Z80C30: optimized for multiplexed bus microprocessors
Pin-compatible to NMOS versions
Two independent 0 to 4.1 Mbps, full-duplex channels, each with separate crystal oscil-
lator, Baud Rate Generator (BRG), and Digital Phase-Locked Loop (DPLL) for clock
recovery
Multiprotocol operation under program control; programmable for NRZ, NRZI or FM
data encoding
Asynchronous Mode with Five to Eight Bits and One, One and One-Half, or Two Stop
Bits Per Character, Programmable Clock Factor, Break Detection and Generation; Par-
ity, Overrun, and Framing Error Detection
Synchronous Mode with Internal or External Character Synchronization on One or
Two Synchronous Characters and CRC Generation and Checking with CRC-16 or
CRC-CCITT Preset to either 1s or 0s
SDLC/HDLC Mode with Comprehensive Frame-Level Control, Automatic Zero Inser-
tion and Deletion, I-Field Residue Handling, Abort Generation and Detection, CRC
Generation and Checking, and SDLC Loop
Software Interrupt Acknowledge Feature (not available with NMOS)
Local Loopback and Auto Echo Modes
Supports T1 Digital Trunk2
Enhanced DMA Support (not available with NMOS) 10 x 19-Bit Status FIFO 14-Bit
Byte Counter
Speeds
Z85C3O: 8.5, 10, 16.384 MHz
Z80C3O: 8, 10 MHz
Other Features for Z85C30 Only
Some of the features listed below are available by default. Some of them (features with *)
are disabled on default to maintain compatibility with the existing Serial Communications
Controller (SCC) design, and “program to enable through WR7”:
PS011706-0511 Overview
CMOS SCC Serial Communications Controller
Product Specification
2
New programmable WR7 (Write register 7 prime) to enable new features
Improvements to support SDLC mode of synchronous communication:
Improve functionality to ease sending back-to-back frames
Automatic SDLC opening Flag transmission
Automatic Tx Underrun/EOM Latch reset in SDLC mode
Automatic RTS deactivation
TxD pin forced High in SDLC NRZI mode a f ter closing flag
Complete CRC reception
Improved response to Abort sequence in status FIFO
Automatic Tx CRC generator preset/reset
Extended Read for Write registers
Write data set-up timing improvement
Improved AC timing:
3 to 3.6 PCLK access recovery time
Programmable DTR/REQ timing
Write data to falling edge of WR setup time requirement is now eliminated
Reduced INT timing
Other features include:
Extended Read function to read back the written value to the Write registers
Latching RRO during read
RRO, bit D7 and RR10, bit D6 now has reset default value
PS011706-0511 General Descripti on
CMOS SCC Serial Communications Controller
Product Specification
3
General Description
The Z80C30/Z85C30 Serial Communications Controller (SCC), is a pin and software
compatible CMOS member of the SCC family introduced by Zilog in 1981. It is a dual-
channel, multiprotocol data communications peripheral that easily interfaces with CPU’s
with either multiplexed or nonmultiplexed address/data buses.
The advanced CMOS process offers lower power consumption, higher performance, and
superior noise immunity. The programming flexibility of the internal registers allow the
SCC to be configured to various serial communications applications.
The many on-chip features such as Baud Rate Generators (BRG), Digital Phase Locked
Loops (DPLL), and crystal oscillators reduce the need for an external logic.
Additional features include a 10 x 19-bit status FIFO and 14-bit byte counter to support
high speed SDLC transfers using DMA controllers.
The SCC handles asynchronous formats, synchronous byte-oriented protocols such as
IBM Bisync, and synchronous bit-oriented prot ocols such as HDLC and IBM SDLC. This
device supports virtually any serial data transfer application (for example, cassette,
diskette, tape drives, etc.).
The device generates and checks CRC codes in any synchronous mode and can be
programmed to check data integrity in various modes. The SCC also contains facilities for
modem controls in both channels. In applications where these controls are not required,
the modem controls can be used for general-p urpose I/O. The daisy-chain interrupt hierar-
chy is also supported.
Figure 1 displays a block diagram of the SCC.
PS011706-0511 General Descripti on
CMOS SCC Serial Communications Controller
Product Specification
4
Figure 1.SCC Block Diagram
Channel A
Exploded View
Databus
Control
Interrupt IEI
IEO
INTACK
INT
Control
CPU & DMA
Bus Interface
Control
Interrupt
Logic
Control
Interrupt
Logic
Channel B
Register
Channel A
Register
RxDA
Channel A
Channel B
Receive Logic
Receive MUX
CRC Checker
Data Decode &
Sync Character
Detection
Rec. S tatus
FIFO 3 Byte
Rec. Status
FIFO 3 Byte
SDLC Frame St atus FIFO
10 X 19
CTSA
DCDA
SYNCA
RTSA
DTRA/REQA
Modem/Control Logic
Digital
Phase-Locked
Loop
Baud Rate
Generator Crystal
Oscillator
Amplifier
Receive and T ransmit Clock Multiplexer
Transmit
Buffer
Transmit Logic
Transmit MUX
Data Encoding & CRC
Generation
TxDA
TRxCA
RTxCA
PS011706-0511 Pin Descriptions
CMOS SCC Serial Communications Controller
Product Specification
5
Pin Descriptions
The following links refer to descriptions of the pin functions common to the Z85C30 and
Z80C30 devices.
CTSA, CTSB
DCDA, DCDB
DTR/REQA, DTR/REQB
IEI
IEO
INT
INTACK
PCLK
RxDA, RxDB
RTxCA, RTxCB
RTSA, RT SB
SYNCA, SYNCB
TxDA, TxDB
TRxCA, TRxCB
W/REQA, W/REQB
CTSA, CTSB
Clear To Send (inputs, active Low) . If these pins are programmed for Auto Enable
functions, a Low on the inputs enables the respective transmitters. If not programmed as
Auto Enable, these pins can be used as general-purpose inputs. Both inputs are Schmitt-
trigger buffered to accommodate slow rise-time inputs. The SCC detects pulses on these
inputs and can interrupt the CPU on both logic level transitions.
DCDA, DCDB
Data Carrier Detect (inputs, active Low) . These pins function as receiver enables if
programmed for Auto Enable. Otherwise, these pins are used as general-purpose input
PS011706-0511 Pin Descriptions
CMOS SCC Serial Communications Controller
Product Specification
6
pins. Both pins are Schmitt-trigger buffered to accommodate slow rise-time signals. The
SCC detects pulses on these pins and can interrupt the CPU on both logic level transitions.
DTR/REQA, DTR/REQB
Data Terminal Ready/Request (outputs, active Low) . These outputs follow the state
programmed into the DTR bit. They can also be used as general-purpose outputs or as
Request lines for a DMA controller.
IEI
Interrupt Enable In (input, active High) . IEI is used with IEO to form an interrupt
daisy-chai n w he n th e r e is m ore than one interrupt driven device. A high IEI indicates that
no other higher priority device has an interrupt under service or is requesting an interrupt.
IEO
Interrupt Enable Out (output, active High) . IEO is High only if IEI is High and the
CPU is not servicing the SCC interrupt or the SCC is not requesting an interrupt (interrupt
Acknowledge cycle only). IEO is connected to the next lower priority device’s IEI input
and thus inhibits interrupts from lower priority devices.
INT
Interrupt Request (output, open-drain, active Low) . This signal activates when the
SCC requests an interrupt.
INTACK
Interrupt Acknowledge (input, active Low) . This signal indicates an active Interrupt
Acknowledge cycle. During this cycle, the SCC interrupt daisy chain settles. When RD is
active, the SCC places an interrupt vector on the data bus (if IEI is High). INTACK is
latched by the rising edge of PCLK.
PCLK
Clock (input) . This is the master SCC clock used to synchronize internal signals. PCLK
is a TTL level signal. PCLK is not required to have any phase relationship with the master
system clock. The maximum transmit rate is 1/4 PCLK.
PS011706-0511 Pin Descriptions
CMOS SCC Serial Communications Controller
Product Specification
7
RxDA, RxDB
Receive Data (inputs, active High) . These signals receive serial data at standard TTL
levels.
RTxCA, RTxCB
Receive/Transmit Clocks (inputs, active Low) . These pins can be programmed in sev-
eral different operating modes. In each channel, RTxC can supply the receive clock, the
transmit clock, clock for the Baud Rate Generator, or the clock for the Digital Phase-
Locked Loop. These pins can also be programmed for use with the respective SYNC pins
as a crystal oscillator . The receive clock can be 1, 16, 32, or 64 times the data rate in Asyn-
chronous modes.
RTSA, RTSB
Request To Send (outputs, active Low) . When the Request To Send (R TS) bit in W rite
Register 5 (see Figure 9 on page 22) is set, the RTS signal goes Low. When the RTS bit is
reset in the Asynchronous mode and Auto Enable is ON, the signal goes High after the
transmitter is empty. In Synchronous mode, it strictly follows the state of the RTS bit.
When Auto Enable is OFF, the RTS pins can be used as general-purpose outputs.
SYNCA, SYNCB
Synchronization (inputs or outputs, active Low) . These pins function as inputs,
outputs, or part of the crystal oscillator circuit. In the Asynchronous Receive mode (crystal
oscillator option not selected), these pins are inputs similar to CTS and DCD. In this
mode, transitions on these lines affect the state of the Synchronous/Hunt status bits in
Read Register 0 (see Figure 8 on page 19) but have no other function.
In External Synchronization mode with the crystal oscillator not selected, these lines also
act as inputs. In this mode, SYNC must be driven Low for two receive clock cycles after
the last bit in the synchronous character is received. Character assembly begins on the
rising edge of the receive clock immediately preceding the activation of SYNC.
In the Internal Synchronization mode (Monosync and Bisync) with the crystal oscillator
not selected, these pins act as outputs and are active only during the part of the receive
clock cycle in which synchronous characters are recognized. This synchronous condition
is not latched. These outputs are active each time a synchronization pattern is recognized
(regardless of character boundaries). In SDLC mode, these pins act as outputs and are
valid on receipt of a flag.
PS011706-0511 Pin Descriptions
CMOS SCC Serial Communications Controller
Product Specification
8
TxDA, TxDB
Transmit Data (outputs, active High) . These output signals transmit serial data at stan-
dard TTL levels.
TRxCA, TRxCB
Transmit/Receive Clocks (inputs or outputs, active Low) . These pins can be
programmed in several different operating modes. TRxC may supply the receive clock or
the transmit clock in the input mode or supply the output of the Digital Phase-locked loop,
the crystal oscillator, the Baud Rate Generator, or the transmit clock in the output mode.
W/REQA, W/REQB
Wait/Request (outputs, open-drain when programmed for a Wait function, driven
High or low when programmed for a Request function) . These dual-purpose outputs
can be programmed as Request lines for a DMA controller or as Wait lines to synchronize
the CPU to the SCC data rate. The reset state is Wait.
Z85C30
The following links refer to descriptions of the pin functions specific to the Z85C30
device.
A/B
CE
D7–D0
D/C
RD
WR
A/B
Channel A/Channel B (input) . This signal selects the channel in which the Read or
Write operation occurs.
PS011706-0511 Pin Descriptions
CMOS SCC Serial Communications Controller
Product Specification
9
CE
Chip Enable (input, active Low) . This signal selects the SCC for a Read or Write opera-
tion
D7–D0
Data Bus (bidirectional, tri-state) . These lines carry data and command to and from the
SCC.
D/C
Data/Control Select (input) . This signal defines the type of information transferred to or
from the SCC. A High indicates a data transfer; a Low indicates a command.
RD
Read (input, active Low) . This signal indicates a Read operation and when the SCC is
selected, enables the SCC’s bus drivers. During the Interrupt Acknowledge cycle, this sig-
nal gates the interrupt vector onto the bus if the SCC is the highest priority device request-
ing an interrupt.
WR
Write (input, active Low) . When the SCC is selected, this signal indicates a Write oper-
ation. The coincidence of RD and WR is interpreted as a reset.
Z80C30
The following links refer to descriptions of the pin functions specific to the Z80C30
device.
AD7–AD0
AS
CS0
CS1
DS
R/W
PS011706-0511 Pin Descriptions
CMOS SCC Serial Communications Controller
Product Specification
10
AD7–AD0
Address/Data Bus (bidirectional, active High, Tri-state) . These multiplexed lines
carry register addresses to the SCC as well as data or control information.
AS
Address Strobe (input, active Low) . Addresses on AD7–AD0 are latched by the rising
edge of this signal.
CS0
Chip Select 0 (input, active Low) . This signal is latched concurrently with the
addresses on AD7–AD0 and must be active for the intended bus transaction to occur.
CS1
Chip Select 1 (input, active High) . This second select signal must also be active before
the intended bus transaction can occur . CS1 must remain active throughout the transaction.
DS
Data strobe (input, active Low) . This signal provides timing for the transfer of data into
and out of the SCC. If AS and DS coincide, this confluence is interpreted as a reset.
R/W
Read/Write (input) . This signal specifies whether the operation to be performed is a
Read or a Write.
PS011706-0511 Pin Descriptions
CMOS SCC Serial Communications Controller
Product Specification
11
Pin Diagrams
Figure 2 displays the pin assignm en ts for the Z85C30 and Z80C30 DIP packages.
Figure 2.Z85C30 and Z80C30 DIP Pin Assignments
D1
D3
D5
D7
INT
IEO
IEI
INTACK
+5V
W/REQA
SYNCA
RTxCA
RxDA
TRxCA
TxDA
DTR/REQA
RTSA
CTSA
DCDA
PCLK
D0
D2
D4
D6
RD
WR
A/B
CE
D/C
GND
W/REQB
SYNCB
RTxCB
RxDB
TRxCB
TxDB
DTR/REQB
RTSB
CTSB
DCDB
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Z85C30
AD1
AD3
AD5
AD7
INT
IEO
IEI
INTACK
+5V
W/REQA
SYNCA
RTxCA
RxDA
TRxCA
TxDA
DTR/REQA
RTSA
CTSA
DCDA
PCLK
AD0
AD2
AD4
AD6
DS
AS
R/W
CS0
CS1
GND
W/REQB
SYNCB
RTxCB
RxDB
TRxCB
TxDB
DTR/REQB
RTSB
CTSB
DCDB
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Z80C30
PS011706-0511 Pin Descriptions
CMOS SCC Serial Communications Controller
Product Specification
12
Figure 3 displays the pin assignm en ts for the Z85C30 and Z80C30 PLCC packages.
Figure 3.Z85C30 and Z80C30 PLCC Pin Assignments
IEO
Z85C30
IEI
INTACK
+5V
W/REQA
SYNCA
RTxCA
RxDA
TRxCA
TxDA
NC
A/B
CE
D/C
NC
GND
W/REQB
SYNCB
RTxCB
RxDB
TRxCB
TxDB
INT
D7
D5
D3
D1
D0
D2
D4
D6
RD
WR
NC
DTR/REQA
RTSA
CTSA
DCDA
PCLD
DCDB
CTSB
RTSB
DTR/REQB
NC
7
8
9
10
11
12
13
14
15
16
17
38
37
36
35
34
33
32
31
30
29
39
6 5 4 3 2 1 44 43 42 41 40
18 19 20 21 22 23 24 25 26 27 28
IEO
Z80C30
IEI
INTACK
+5V
W/REQA
SYNCA
RTxCA
RxDA
TRxCA
TxDA
NC
R/W
CS0
CS1
NC
GND
W/REQB
SYNCB
RTxCB
RxDB
TRxCB
TxDB
INT
AD7
AD5
AD3
AD1
AD0
AD2
AD4
AD6
DS
AS
NC
DTR/REQA
RTSA
CTSA
DCDA
PCLK
DCDB
CTSB
RTSB
DTR/REQB
NC
7
8
9
10
11
12
13
14
15
16
17
38
37
36
35
34
33
32
31
30
29
39
6 5 4 3 2 1 44 43 42 41 40
18 19 20 21 22 23 24 25 26 27 28
PS011706-0511 Pin Descriptions
CMOS SCC Serial Communications Controller
Product Specification
13
Figures 4 and 5 display the pin functions for the Z85C30 and Z80C30 devices, respec-
tively. Descriptions for each of these pins can be found in the Functional Descri ptio ns
chapter on page 15.
Figure 4.Z85C30 Pin Functions
Z85C30
Serial
Data
Channel
Clocks
CH-A
Channel
Controls
for Modem,
DMA and
Other
CH-B
Serial
Data
Channel
Clocks
Channel
Controls
for Modem,
DMA and
Other
Data Bus
D7
D6
D5
D4
D3
D2
D1
D0
RD
WR
A/B
CE
D/C
INT
INTACK
IEI
IEO
TxDA
RxDA
TRxCA
RTxCA
SYNCA
W/REQA
DTR/REQA
RTSA
CTSA
DCDA
TxDB
RTxCB
SYNCB
W/REQB
DTR/REQB
RTSB
CTSB
DCDB
RxDB
TRxCB
and Reset
Control
Interrupt
Bus Timing
PS011706-0511 Pin Descriptions
CMOS SCC Serial Communications Controller
Product Specification
14
Figure 5.Z80C30 Pin Functions
Z80C30
Serial
Data
Channel
Clocks
CH-A
Channel
Controls
for Modem,
DMA and
Other
CH-B
Serial
Data
Channel
Clocks
Channel
Controls
for Modem,
DMA and
Other
Data Bus
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
AS
DS
R/W
CS1
CS0
INT
INTACK
IEI
IEO
TxDA
RxDA
TRxCA
RTxCA
SYNCA
W/REQA
DTR/REQA
RTSA
CTSA
DCDA
TxDB
RTxCB
SYNCB
W/REQB
DTR/REQB
RTSB
CTSB
DCDB
RxDB
TRxCB
and Reset
Control
Interrupt
Bus Timing
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
15
Functional Descriptions
The architecture of the SCC device functions as:
A data communications device which transmits and receives data in various protocols
A microprocessor peripheral in which the SCC offers valuable features such as vec-
tored interrupts and DMA support
The SCC’s peripheral and data communication features are described in the following sec-
tions.
Figure 1 on page 4 displays the SCC blo ck diagram. Figures 6 and 7 display the details of
the communication between the receive and transmit logic to the system bus. The features
and data path for each of the SCC’s A and B channels are identi ca l.
Figure 6. SCC Transmit Data Path
From Receiver
CRC-Gen
Zero Insert
(5 Bits)
20-Bit TX Shift Register
SYNC Register SYNC Register
Internal Data Bus
To Other Channel
Internal TXD
TXD
NRZ
Encode
Transmit
MUX & 2-Bit
Delay
Transmit Clock
TX Buffer
1 Byte
Final TX
MUX
WRB
WR6
Sync
Sync
SDLC
WR7
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
16
I/O Interface Capabilities
System comm unication to and from the SCC de vice is performed through the SCC’s regis-
ter set. There are sixteen Write registers and eight Read registers.
Throughout this document, Write and Read registers a re referenced with the following
notation:
‘WR’ for Write Register
‘RR’ for Read Register
Figure 7. SCC Receive Data Path
To Transmit Section
MUX
NRZI Decode
MUX
Internal TXD
DPLL SYNC Register
& Zero Delete
OUT
SDLC-CRC CRC
Checker CRC Result
SYNC
CRC
CRC Delay
Register (8 bits)
Receive Shift
Register
3-Bit
RXD
DPLL
IN DPLL
1-Bit
Hunt Mode (BISYNC)
14-Bit Counter Rec. Error Logic
BRG
Output
Rec. Error FIFO
3 Byte D e ep
Rec. Error FIFO
3 Byte D e ep
Status FIFO
10 X 19 Frame
I/O Data buffer
Internal Data Bus
CPU/I/O
BRG
Input 16-Bit Down Counter DIV 2
Upper Byte (WR13)
Time Constant Lower Byte (WR12)
Time Constant
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
17
For example,
WR4A Write Register 4 for channel A
RR3 Read Register 3 for either/both channels
Tables 1 and 2 list the SCC registers and provide a brief description of their functions.
Table 1. SCC Read Register Functions
Register Function
RR0 Transmit/Receive buffer status and External status
RR1 Special Receive Condition status
RR2 Modified interrupt vector (Channel B only) Unmodified interrupt vector (Channel A only)
RR3 Interrupt Pending bits (Channel A only)
RR8 Receive Buffer
RR10 Miscellaneous status
RR12 Lower byte of Baud Rate Generator time constant
RR13 Upper byte of Baud Rate Generator time constant
RR15 External/Status interrupt information
Table 2. SCC Write Register Functions
Register Function
WR0 CRC initialize, initialization commands for the various modes, register pointers
WR1 Transmit/Receive interrupt and data transfer mode definition
WR2 Interrupt vector (accessed through either channel)
WR3 Receive parameters and control
WR4 Transmit/Receive miscellaneous parameters and modes
WR5 Transmit parameters and controls
WR6 Sync characters or SDLC ad d ress field
WR7 Sync character or SDLC flag
WR7* Extended Fe at ur e an d FIFO Con tr o l (WR7 Prime) 85C30 Only
WR8 Transmit buffer
WR9 Master interrupt control and reset (accessed through either channel)
WR10 Miscellaneous tr an sm itter/receiver control bit s
WR11 Clock mode control
WR12 Lower byte of Baud Rate Generator time constant
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
18
The following three methods move data, status and control information in and out of the
SCC; each is described in this section.
Polling
Interrupts (vectored and nonvectored)
CPU/DMA Block Tra nsf er, in which BLOCK TRANSF ER mo de can be implemen ted
under CPU or DMA control
Polling
When polling, all interrupts are disabled. Three status registers in the SCC are automati-
cally updated when any function is performed. For example, End-Of-Frame in SDLC
mode sets a bit in one of these status registers. The purpose of polling is for the CPU to
periodically read a status register until the register contents indicate the need for data to be
transferred. Only one register is read, and depending on its contents, the CPU either writes
data, reads data, or continues. Two bits in the register indicate the need for data transfer.
An alternative is a poll of the Interrupt Pending register to determine the source of an
interrupt. The status for both channels resides in one register.
Interrupts
The SCC’s interrupt structure supports vectored and nested interrupts. Nested interrupts
are supported with the interrupt acknowledge feature (INTACK pin) of the SCC.
This allows the CPU to recognize the occurrence of an interrupt, and reenable higher pri-
ority interrupts. Because an INTACK cycle releases the INT pin from the active state, a
higher priority SCC interrupt or another h i gher priority device can interrupt the CPU .
When an SCC responds to an Interru pt Ackn owledg e signal (INTACK) from the CPU, an
interrupt vector can be placed on the data bus. This vector is written in WR2 and can be
read in RR2A or RR2B. To speed interrupt response time, the SCC can modify three bits
in this vector to indicate status. If the vector is read in Channel A, status is never included.
If the vector is read in Channel B, status is always included.
Each of the six sources of interrupts in the SCC (Transmit, Receive, and External/Status
interrupts in both channels) has three bits associated with the interrupt source.
WR13 Upper byte of Baud Rate Generator time constant
WR14 Miscellaneous control bits
WR15 External/Status interrupt control
Table 2. SCC Write Register Functions (cont inued)
Register Function
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
19
Interrupt Pending (IP), Interrupt Under Service (IUS), and Interrupt Enable (IE). Opera-
tion of the IE bit is straight forward. If the IE bit is set for a given interrupt source, then
that source can request interrupts. The exception is when the MIE (Master Interrupt
Enable) bit in WR9 is reset and no interrupts can be requested. The IE bits are Write only.
The other two bits are related to the interrupt priority chain (see Figure 8 on page 19). As a
microprocessor peripheral, the SCC can request an interrupt only when no higher priority
device is requestin g one, that is, when IEI is High. If the device in question requests an
interrupt, it pulls down INT. The CPU responds with INTACK, and the interrupting device
places the vector on the data bus.
Figure 8. SCC Interrupt Priority Schedule
The SCC can also execute an interrupt acknowledge cycle through software. In some CPU
environments, it is difficult to create the INTACK signal with the necessary timing to
acknowledge interrupts and allow the nesting of interrupts. In these cases, the INTACK
signal can be created with a software command to the SCC.
In the SCC, the Interrupt Pending (IP) bit signals a need for interrupt servicing. When an
IP bit is 1 and the IEI input is High, the INT output is pulled Low, requesting an interrupt.
In the SCC, if the IE bit is not set by enabling interrupts, then the IP for that source is
never set. The IP bits are readable in RR3A.
The IUS bits signal that an interrupt request is being serviced. If an IUS is set, all interrupt
sources of lower priority in the SCC and external to the SCC are prevented from request-
ing interrupts.
The internal interrupt sources are inhibited by the state of the internal daisy chain, while
lower priority devices are inhibited by the IEO output of the SCC being pulled Low and
propagated to su bsequent peripherals. An IUS bit is set during an Interrupt Acknowledge
cycle, if there are no higher priority devices requesting interrupts.
There are three types of interrupts:
Transmit
Receive
+5 V
+5 V
D7–D0
INT
INTACK
IEI D7–D0 INT INTACK IEO IEI D7–D0 INT INTACK IEO IEI D7–D0 INT INTACK
Peripheral PeripheralPeripheral
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
20
External/Status
Each interrupt type is enabled under program control with Channel A having higher prior-
ity than Channel B, and with Receiver , T ransm it, and External/S tatus interrupts prioritized
in that order within each channel.
When enabled, the receiver interrupts the CPU in one of three ways:
Interrupt on First Receive Character or Special Receive Condition
Interrupt on All Receive Characters or Special Receive Conditions
Interrupt on Special Receive Conditions Only
Interrupt on First Character or Special Condit ion and Interrupt on Special Condition Only
are typically used with the Block T ransfer mo de. A special Receive Condition is one of the
following. receiver overrun, framing error in Asynchronous mode, end-of-frame in SDLC
mode and, optionally, a parity error. The Special Receive Condition interrupt is different
from an ordinary receive character available interrupt only by the status placed in the vec-
tor during the Interrupt Acknowledge cycle. In Interrupt on First Receive Character, an
interrupt occurs from Special Receive Conditions anytime after the first receive character
interrupt.
The main function of the External/Status interrupt is to monitor the signal transitions of
the CTS, DCD, and SYNC pins, however, an External/Status interrupt is also caused by a
T ransmit Underrun condition; a zero count in the Baud Rate Gene rator; by the detection of
a Break (Asynchronous mode), Abort (SDLC mode) or EOP (SDLC Loop mode)
sequence in the data stream. The interrupt caused by the Abort or EOP has a special fea-
ture allowing the SCC to interrupt when the Abort or EOP sequence is detected or termi-
nated. This feature facilitates the proper termination of the current message, correct
initialization of the next message, and the accurate timing of the Abort condition in exter-
nal logic in SDLC mode. In SDLC Loop mode, this feature allows secondary stations to
recognize the primary station regaining control of the loop during a poll sequence.
Software Interrupt Acknowledge
On the CMOS version of the SCC, the SCC interrupt acknowledge cycle can be initiated
through software. If W rite Register 9 (WR9) bit D5 is set, Read Register 2 (RR2) results in
an interrupt acknowledge cycle to be executed internally. Like a hardware INTACK cycle,
a software acknowledge causes the INT pin to return High, the IEO pin to go low and set
the IUS latch for the highest priority interrupt pending.
Similar to using the hardware INTACK signal, a software acknowledge cycle requires that
a Reset Highest IUS command be issued in the interrupt service routine. Whenever an
interrupt acknowledge cycle is used, hardware or software, a reset highest IUS command
is required. If RR2 is read from channel A, the unmodified vector is returned. If RR2 is
read from channel B, then the vector is modified to indicate the source of the interrupt.
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
21
The Vector Includes Status (VIS) and No Vector (NV) bits in WR9 are ignored when bit
05 is set to 1.
When the INTACK and IEI pins are not being used, they should be pulled up to VCC
through a resistor (10 K typical).
CPU/DMA Block Transfer
The SCC provides a Block Transfer mode to accommodate CPU block transfer functions
and DMA controllers. The Block Transfer mode uses the WAIT/REOUEST output in con-
junction with the Wait/Request bits in WR1. The WAIT /REOUEST output can be
defined under software control as a WAIT line in the CPU Block Transfer mode or as a
REQUEST line in the DMA Block Transfer mode.
To a DMA controller, the SCC REQUEST output indicates that the SCC is ready to trans-
fer data to or from memory To the CPU, the WAIT line indicates that the ESCC is not
ready to transfer data, thereby requesting that the CPU extend the I/O cycle. The DTR/
REQUEST line allows full-duplex operation under DMA control.
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
22
SCC Data Communications Capabilities
The SCC provides two independent full-duplex programmable channels for use in any
common asynchronous or synchron ous data communication protocols; see Figure 9. Each
data communication channel has identical feature and capabilities.
Asynchronous Modes
Send and Receive is accomplished independently on each channel with five to eight bits
per character, plus optional even or odd parity. The transmitters can supply one, one-and-
a-half, or two stop bits per character and can provide a break output at any time. The
receiver break-detection logic interrupts the CPU both at the start and at the end of a
received break.
Reception is protected from spikes by a transient spike-rejection mechanism that checks
the signal one-half a bit time after a Low level is detected on the receive data input (RxDA
or RxDB pins). If the Low does not persist (a transient), the character assembly process
does not start.
Figure 9. SCC Protocols
Flag Address Information CRC1 CRC2
Information Flag
Data
SYNC
CRC1
Signal
CRC1 CRC2
Marking Line
Data CRC2
SYNC Data Data
CRC1 CRC2
SYNC Data Data
Start
SDLC/HDLC/X.25
Parity
Stop
Data Data Data Markin g Lin e
External Sync
Bisync
Monosync
Asynchronous
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
23
Framing errors and overrun errors are detected and buffered together with the partial char-
acter on which they occur. Vectored interrupts allow fast servicing or error conditions
using dedicated routines. A built-in checking process avoids the interpretation of a fram-
ing error as a new start bit. A framing error results in the addition of one-half a bit time to
the point at which the search for the next start bit begins.
The SCC does not require symmetric transmit and receive clock signals – a feature that
allows the use of a wide variety of clock so urces. The transmitter and receiver handle data
at a rate supplied to the receive and transmit clock inputs. In Asynchronous modes, the
SYNC pin can be programmed as an input used for functions such as monitoring a ring
indicator.
Synchronous Modes
The SCC supports both byte and bit-oriented synchronous communication. Synchronous
byte-oriented protocols are handled in several mode s. They allow character synchroniza-
tion with a 6-bit or 8-bit sync character (Monosync), and a 12-bit or 16-bit synchroniza-
tion pattern (Bisync), or with an external sync signal. Leading sync characters are
removed without interrupting the CPU.
5- or 7-bit synchronous characters are detected with 8- or 16-bit patterns in the SCC by
overlapping the larg er pattern across multiple incoming synchronous characters, as shown
in Figure 10.
CRC checking for Synchronous byte-oriented modes is delayed by one character time so
that the CPU can disable CRC checking on specific characters. This feature permits the
implementation of protocols such as IBM Bisync.
Both CRC-16 (X16 + X15 + X12 +1) and CCITT (X16 + X12 + X5 + 1) error-checking
polynomials are supported. Either polynomial can be selected in all Synchronous modes.
You can preset the CRC generator and checker to all 1’s or all 0’s. The SCC also provides
a feature that automatically transmits CRC data when no other data is available for trans-
Figure 10. Detecting 5- or 7-Bit Synchronous Characters
Data Data Data
Data
SYNC SYNC
7 Bits
8
16
SYNC
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
24
mission. This feature allows for high speed transmissions under DMA control, with no
need for CPU intervention at the end of a message.
When there is no data or CRC to send in Synchronous modes, the transmitter inserts 6-,8-,
or 16-bit sync characters, regardless of the programmed character length.
SDLC Mode
The SCC supports Synchro no us bit-oriented protocols, such as SDLC and HDLC, by per-
forming automatic flag sending, zero insertion, and CRC generation. A special command
is used to abort a frame in transmission. At the end of a message, the SCC automatically
transmits the CRC and trailing flag when the transmitter underruns. The transmitter can
also be programmed to send an idle line consisting of continuous flag characters or a
steady marking condition.
If a transmit underrun occurs in the middle of a message, an external/status interrupt warns
the CPU of this status change, issuing an abort. The SCC can also be programmed to send
an abort itself in case of an underrun, relieving the CPU of this task. One to eight bits per
character can be sent, allowing reception of a message with no prior information about the
character structure in the information field of a frame.
The receiver automatically acquires synchronization on the leading flag of a frame in
SDLC or HDLC and provides a synchronization signal on the SYNC pin (an interrupt can
also be programmed). The receiver can be programmed to search for frames addressed by
a single byte (or four bits within a byte) of a user -selected address or to a global broadcast
address. In this mode, frames not matching either the user-selected or broadcast address
are ignored.
The number of address bytes are extended under software control. For receiving data, an
interrupt on the first received character, or an interrupt on every character, or on special
condition only (end-of-frame) can be selected. The receiver automatically deletes all 0’s
inserted by the transmitter during character assembly CRC is also calculated and is auto-
matically checked to validate frame transmission. At the end of transmission, the status of
a received frame is available in the status registers. In SDLC mode, the SCC must be pro-
grammed to use the SDLC CRC polynomial, but the generator and checker can be preset
to all 1’s or all 0’s. The CRC inverts before transmission and the receiver checks against
the bit pattern 0001110100001111.
NRZ, NRZI or FM coding can be used in any 1 x mode. The parity options available in
Asynchronous modes are available in Synchronous modes.
SDLC Loop Mode
The SCC supports SDLC Loop mode in addition to normal SDLC. In an SDLC Loop, a
primary controller stati on manages the message traffic fl ow on the loop and any number of
secondary stations. In SDLC Loop mode, the SCC performs the functions of a secondary
station while an SCC operating in regular SDLC mode acts as a controller; see Figure 11.
The SDLC loop mode can be selected by setting WR10 bit D1.
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
25
A secondary station in an SDLC Loop is always listening to the messages sent around the
loop and passes these messages to the rest of the loop by retransmitting them with a one-
bit-time delay. The secondary station places its own message on the loop only at specific
times.
The controller signals that secondary stations can transmit messages by sending a special
character, called an End Of Poll (EOP), around the loop. The EOP character is the bit pat-
tern 11111110. Because of zero insertion during messages, this bit pattern is unique and
easily recognized.
When a secondary station contains a message to transmit and recognizes an EOP on the
line, it changes the last binary 1 of the EOP to a 0 before transmission. This change has the
effect of turning the EOP into a flag sequence. The secondary station now places its mes-
sage on the loop and terminates the message with an EOP. Any secondary stations further
down the loop with messages to transmit append their messages to the message of the first
secondary station by the same process. Any secondary stations without messages to send
echo the incoming message and are prohibited from placing messages on the loop (except
when recognizing an EOP). In SDLC Loop mode, NRZ, NRZI, and FM coding can be
used.
The SCC’s ability to receive high speed back-to-back SDLC frames is maximized by a 10-
deep by 19-bit wide status FIFO. When enabled (through WR15, bit D2), it provides the
DMA the ability to continue to transfer data into memory so that the CPU can examine the
Figure 11. An SDLC Loop
Secondary #2 Secondary #3
Secondary #4
Controller
Secondary #1
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
26
message later. For each SDLC frame, a 14-bit byte count and 5 status/error bits are stored.
The byte count and status bits are accessed through Read Registers 6 and 7. Read Regis-
ters 6 and 7 are only accessible when the SDLC FIFO is enabled. The 10 x 19 status FIFO
is separate from the 3-byte receive data FIFO.
Baud Rate Generator
Each channel in the SCC contains a programmable Baud Rate Generator (BRG). Each
generator consists of two 8-bit time constant registers that form a 16-bit time constant, a
16-bit down counter, and a flip-flop on the output producing a square wav e. On star tup,
the output flip-flop is set in a High state, the value in the time constant register is loaded
into the counter, and the counter starts counting down. The output of the BRG toggles
when reaching 0, the value in the time constant register is loaded into the co unt er, and the
process is repeated. The time constant can be changed at any time, but the new value does
not take effect until the next load of the counter.
The output of the BRG can be used as either the transmit clock, the receive clock, or both.
It can also drive the Digital Phase-locked loop (see Digital Phase-Locked Loop).
If the receive clock or transmit clock is not programmed to come from the TRxC pin, the
output of the BRG can be echoed out thro ugh the TRxC pin. The following formula relates
the time constant to the baud rate where PCLK or RTxC is the BRG input frequency in
Hertz. The clock mode is 1, 16, 32, or 64, as selected in Write Register 4, bits D6 and D7.
Synchronous operation modes select 1 and Asynchronous modes select 16, 32 or 64.
Digital Phase-Locked Loop
The SCC contains a Digital Phase-Locked Loop (DPLL) to recover clock information
from a data stream with NRZI or FM encoding. The DPLL is driven by a clock that is
nominally 32 (NRZI) or 16 (F M) times the data rate. The DPLL uses this clock, along with
the data stream, to construct a clock for the data. This clock is used as the SCC receive
clock, the transmit clock, or both. When the DPLL is selected as th e transmit cloc k source,
it provides a jitter-free clock output that is the DPLL input frequency divided by the
appropriate divisor for the selected encoding technique.
For NRZI encoding, the DPLL counts the 32x clock to create nominal bit times. As the
32x clock is counted, the DPLL is searching the incoming data stream for edges (either 1
to 0, or 0 to 1). Whenever an edge is detected, the DPLL makes a count adjustment (during
the next counting cycle), produ ci ng a terminal count closer to the center of the bit cell.
Time Constant = PCLK or RTxC Frequency
2(Baud Rate)(Clock Mode) -2
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
27
For FM encoding, the DPLL again counts from 0 to 31, but with a cycle corresponding to
two bit times. When the DPLL is locked, the clock edges in the data stream occur between
counts 15 and 16 an d between counts 31 and 0. The DPLL loo ks for edges only during a
time centered on the 15 to 16 counting transition.
The 32x clock for the DPLL can be programmed to come from either the RTxC input or
the output of the BRG. The DPLL output can be programmed to be echoed out of the SCC
through the TRxC pin (if this pin is not being used as an input).
Data Encoding
The SCC can be programmed to encode and decode the serial data in four different meth-
ods; see Figure 12. In NRZ encoding, a 1 is represented by a High level and a 0 is repre-
sented by a Low level. In NRZI encoding, a 1 is represented by no change in level and a 0
is represented by a change in level.
In FM1 (more properly, bi-phase mark), a transition occurs at the beginning of every bit
cell. A 1 is represented by an additional transition at the center of the bit cell and a 0 is rep-
resented by no additional transition at the center of the bit cell.
In FM0 (bi-phase space), a transition occurs at the beginning of every bit cell. A 0 is repre-
sented by an additional transition at the center of the bit cell, and a 1 is represented by no
additional transition at the center of the bit cell.
In addition to these four methods, the SCC can be used to decode Manchester (bi-phase
level) data by using the DPLL in the FM mode and programming the receiver for NRZ
data. Manchester encoding always produces a transition at the center of the bit cell. If the
transition is 0 to 1, the bit is a 0. If the transition is 1 to 0, the bit is a 1.
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
28
Auto Echo and Local Loopback
The SCC is capable of automatically echoing everything it receives. This feature is useful
mainly in Asynchronous modes, but works in Synchronous and SDLC modes as well.
Auto Echo mode (Tx0 is Rx0) is used with NRZI or FM encoding with no additional delay
because the data stream is not decoded before retransmission. In Auto Echo mode, the
CTS input is ignored as a transmitter enable (although transitions on this input can still
cause interrupts if programmed to do so). In this mode, the transmitter is actually bypassed
and the programmer is responsible for disabling transmitter interrupts and WAIT/
REQUEST on transmit.
The SCC is also capable of local loopback. In this mode, TxD or RxD is similar to Auto
Echo mode. However, in Local Loopback mode the internal transmit data is tied to the
internal receive data and RxD is ignored (except to be echoed out through TxD). The CTS
and DCD inputs are also ignored as transmit and receive enables. However, transitions on
these inputs can still cause interrupts. Local Loopback works in Asynchronous, Synchro-
nous and SDLC modes with NRZ, NRZI or FM coding of the data stream.
SDLC FIFO Frame Status FIFO Enhancement
The SCC’s ability to receive high speed back-to-back SDLC frames is maximized by a 10-
deep by 19-bit wide status FIFO. When enabled (through WR15, bit D2), it provides the
Figure 12. Data Encoding Methods
Data
NRZ
NRZI
FM1
FM0
Manchester
110 0
01
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
29
DMA the ability to continue to transfer data into memory so that the CPU can examine the
message later. For each SDLC frame, a 14-bit byte count and 5 status/error bits are stored.
The byte count and status bits are accessed through Read Registers 6 and 7. Read Regis-
ters 6 and 7 are only accessible when the SDLC FIFO is enabled. The 10x19 status FIFO
is separate from the 3-byte receive data FIFO.
When the enhancement is enabled, the status in Read Register 1 (RR1) and byte count for
the SDLC frame are stored in the 10 x 19 bit status FIFO. This arrangement allows the
DMA controller to transfer the next frame into memory while the CPU verifies that the
message was properly received.
Summarizing the operation; data is received, assembled, and loaded into the eight byte
FIFO before being transferred to memory by the DMA controller. When a flag is received
at the end of an SDLC frame, the frame byte count from the 14-bit counter and five status
bits are loaded into the status FIFO for verification by the CPU. The CRC checker auto-
matically resets in preparation for the next frame which can begin immediately. Because
the byte count and status are saved for each frame, the message integrity is verified at a
later time. The status information for up to 10 frames is stored before a status FIFO over-
run occurs.
If a frame is terminated with an ABORT, the byte count is loaded to the status FIFO and
the counter resets for the next frame.
FIFO Detail
For more details about FIFO operation, see Figure 13 on page 30.
Enable/Disable
This FIFO is implemented is enabled when WR15, bit D2, is set and the SCC is in the
SDLC/HDLC mode. Otherwise, the status register contents bypass the FIFO and go
directly to the bus interface (the FIFO pointer logic is reset either when disabled or
through a channel or Power-On Reset). When the FIFO mode is disabled, the SCC is
downward-compatible with the NMOS Z8530. The FIFO mode is disabled on power-up
(WR15 D2 is set to 0 on reset). The effects of backward compatibility on the register set
are that RR4 is an image of RR0, RR5 is an image of RR1, RR6 is an image of RR2 and
RR7 is an image of RR3. For more details about the added registers, see Figure 16 on page
34. The status of the FIFO Enable signal is ob tained b y readi ng RR1 5, bit D2. If the F IFO
is enabled, the bit is set to 1; otherwise, it resets.
Read Operation
When WR15 bit D2 sets and the FIFO is not empty, the next read to status register RR1 or
registers RR7 and RR6, is from the FIFO. Reading status register RR1 causes one location
of the FIFO to become empty. Status is read after reading the byte count, otherwise the
count is incorrect. Before the FIFO underflows, it is disabled. In this case, the multiplexer
is switched allowing status to read directly from the status register. Reads from RR7 and
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
30
RR6 contain bits that are undefined. Bit D6 of RR7 (FIFO Data Available) determines if
status data is coming from the FIFO or directly from the status register, which sets to 1
when the FIFO is not empty. Not all status bit s are stored in the FIFO. The All Sent, Parity,
and EOF bits bypass the FIFO. Status bits sent through the FIFO are Residue Bits (3),
Overrun, and CRC Error.
Figure 13. SDLC Frame Status FIFO
Over Equal
Reset on Flag Detect
Increment on Byte Detection
Enable Count in SDLC
End of Frame Signal
Status Read Comp
Tail Pointer
4-Bit Counter
Head Pointer
4-Bit Counter
4-Bit Comparator
14 Bits
Byte Counter
Frame Status FIFO Circuitry
5 Bits
FIFO Array
10 Deep by 19 Bits Wide
SCC Status Reg
Residue Bits (3)
Overrun, CRC Error
RR1
5 Bits
EN
6 Bits 8 Bits
6-Bit MUX
2 Bits
EOF = 1
6 Bits
RR1
Bit 7 Bit 6 Bits 5-0 RR6 FIFO Enable
RR7 D5-D0 + RR6 D7-D0
Byte Counter Contains 14 bits
for a 16 KByte maximum count
RR7 D6
FIFO Da ta available status bit Status Bit set to 1
When reading from FIFO
RR7 D7
FIFO Overflow Status Bit
MSB pf RR(7) is set on Status FIFO overflow
WR(15) Bit 2
Set Enables
S t atus FIFO
In SDLC Mode the following definitions apply
Interface
to SCC
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
31
The sequence for operation of the byte count and FIFO logic is to read the registers in the
following order. RR7, RR6, and RR1 (reading RR6 is optional). Additional logic prevents
the FIFO from being emptied by multiple reads from RR1. The read from RR7 latches t he
FIFO empty/full status bit (D6) and steers the status multiplexer to read from the SCC
megacell instead of the status FIFO (since the status FIFO is empty). The read from RR1
allows an entry to be read from the FIFO (if the FIFO was empty, logic was added to pre-
vent a FIFO underflow condition).
Write Operati on
When the end of an SDLC frame (EOF) is received and the FIFO is enabled, the contents
of the status and byte-count registers are loaded into the FIFO. The EOF signal is used to
increment the FIFO. If the FIFO overflows, RR7, bit D7 (FIFO Overflow) sets to indicate
the overflow. This bit and the FIFO control logic is reset by disabling and reenabling the
FIFO control bit (WR15, bit 02). For details of FIFO control timing during an SDLC
frame, see Figure 14.
Programming
The SCC contains Write re gis t er s in ea c h channel that are program m ed by th e s ystem sep-
arately to configure the functional personality of the channels.
Z85C30
In the SCC, the data registers are directly addressed by selecting a High on the D/
C
pin.
With all other registers (except WR0 and RR0), programming the W rite registers requires
two Write operations and reading the read registers requires both a Write and a Read oper-
ation. The first write is to WR0 and contains three bits that point to the selected register.
Figure 14. SDLC Byte Counting Detail
Don’t Load
Counter On
1st Flag
Reset Byte
Counter Here
Reset
Byte Counter
Load Counter
Into FIFO and
Increment PTR
Internal Byte Strobe
Increments Counter
Reset
Byte Counter
Internal Byte Strobe
Increments Counter
Reset
Byte Counter
Load Counter
Into FIFO and
Increment PTR
FADDDDCCF
070
FADDDDCCF
07
0
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
32
The second write is the actual control word for the selected register, and if the second
operation is read, the selected Read register is accessed. All the SCC registers, including
the data registers, can be accessed in this fashion. The pointer bits are automatically
cleared after the Read or Write operation so that WR0 (or RR0) is addressed again.
Z80C30
All SCC registers are directly addressable. A command issued in WR0B controls how the
SCC decodes the address placed on the address/data bus at the beginning of a Read or
Write cycle. In the Shift Right mode, the channel select A/B is taken from AD0 and the
state of AD5 is ignored. In the Shift Left mode, the channel select A/B is taken from AD5
and the state of AD0 is ignored. AD7 and AD6 are always ignored as address bits and the
register address occupies AD4-AD1.
Z85C30/Z80C30 Setup
Initialization
The system program first issues a series of commands to initialize the basic mode of
operation. This is followed by other commands to qualify conditions within the selected
mode. For exampl e, in the Async hro no us mod e, character length, clock rate, number of
stop bits, and even or odd parity must be set first. The interrupt mode is set, and finally, the
receiver and transmitter are enabled.
Write Registers
The SCC contains 15 Write registers for th e 80C30, while there are 16 for the 85C30 (one
more additional Write register if counting the transmit buffer) in each channel. These
Write registers are programmed separately to configure the functional ‘personality’ of the
channels. There are two registers (WR2 and WR9) shared by the two channels that are
accessed through either of them. WR2 contains the interrupt vector for both channels,
while WR9 contains the interrupt control bits and reset commands. Figures 15 through 18
display the format of each Write register.
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
33
Figure 15. Write Register Bit Functions
Register 0
*
00
01
10
11
00
01
10
11
Null Code
Null Code
Null Code
Null Code
Null Code
* B Channel Only
Reset Rx CRC Checker
Reset Tx CRC Checker
Reset Tx Underrun/EOM Latch
Reset Ext/Status Interrupts
Send Abort
Enable Int on Next Rx Character
Reset Tx Int Pending
Error Reset
Reset Highest IUS
Select Shift Left Mode
Select Shift Right Mode
0
0
0
0
0
01
1
0
0
00
0
0
0
1
11
1
1
1
1
1
1
1
D7 D6 D5 D4 D3 D2 D1 D0
Write Register 0 (multiplexed bus mode)
D7 D6 D5 D4 D3 D2 D1 D0
Write Register 0 (non-multiplexed bus mode)
Null Code
0
0
01
10
11
* With Point High Command
Reset Rx CRC Checker
Reset Tx CRC Generator
Reset Tx Underrun/EOM Latch
Register 1
Register 2
Register 3
Register 4
Register 5
Register 6
Register 7
Register 8
Register 9
Register 10
Register 11
Register 12
Register 13
Register 14
Register 15
*
000
00
00
000
00
000
0000
0
00
0
0
11
11
111
1
111
111
1
1
1
1
1
1
11
1
000
00
00
000
00
111
1
11
1
111
1
1
Null Code
Point High
Reset Ext/Status Interrupts
Send Abort (SDLC)
Enable Int on Next Rx Character
Reset Tx Int Pending
Error Reset
Reset Highest IUS
D7 D6 D5 D4 D3 D2 D1 D0
Write Register 1
00
00
1
1
11
Ext Int Enable
Tx Int Enable
Parity is Special Condition
Rx Int on Special Condition Only
Int on all Rx Characters or Special Condition
Rx Int on First Character or Special Condition
WAIT/DMA Request on
Receive /Transmit
Rx Int Disable
WAIT/DMA Request Function
WAIT/DMA Request
D7 D6 D5 D4 D3 D2 D1 D0
Write Register 2
V0
V1
V2
V3
V4
V5
V6
V7
Interrupt
Vector
D7 D6 D5 D4 D3 D2 D1 D0
Write Register 3
Rx Enable
Sync Character Load Inhibit
Address Search Mode (SDLC)
Rx CRC Enable
Enter Hunt Mode
Auto Enables
0
0
00
1
11
1
Rx 5 Bits/Character
Rx 7 Bits/Character
Rx 6 Bits/Character
Rx 8 Bits/Character
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
34
Figure 16. Write Register Bit Functions
D7 D6 D5 D4 D3 D2 D1 D0
Write Register 4
Parity Enable
Parity EVEN/ODD
0
0
0
01
1
11
0
0
0
01
1
11
0
0
0
01
1
11
Sync Modes Enable
1 Stop Bit/Character
1 1/2 Stop Bits/Character
2 Stop Bits/Character
8-Bit Sync Character
16-Bit Sync Character
SDLC Mode (01111110 Flag)
External Sync Mode
X1 Clock Mode
X16 Clock Mode
X32 Clock Mode
X64 Clock Mode
D7 D6 D5 D4 D3 D2 D1 D0
Write Register 5
0
00
0
1
1
1
1
Tx CRC Enable
RTS
SDLC/CRC-16
Tx Enable
Send Break
DTR
Tx 5 Bits (or Less)/Character
Tx 7 Bits/Character
Tx 6 Bits/Character
Tx 8 Bits/Character
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
35
Figure 17. Write Register Bit Functions
D7 D6 D5 D4 D3 D2 D1 D0
Write Register 6
Sync7
Sync1
Sync7
Sync3
ADR7
ADR7
Sync6
Sync0
Sync6
Sync2
ADR6
ADR6
Sync5
Sync5
Sync5
Sync1
ADR5
ADR5
Sync4
Sync4
Sync4
Sync0
ADR4
ADR4
Sync3
Sync3
Sync3
1
x
ADR3
Sync2
Sync2
Sync2
1
x
ADR2
Sync1
Sync1
Sync1
1
x
ADR1
Sync0
Sync0
Sync0
1
x
ADR0
Monosync, 8 Bits
Monosync, 6 Bits
Bisync, 16 Bits
Bisync, 12 Bits
SDLC
SDLC (Add ress Range)
D7 D6 D5 D4 D3 D2 D1 D0
Write Register 7
Sync7
Sync5
Sync15
Sync11
Monosync, 8 Bits
Monosync, 6 Bits
Bisync, 16 Bit s
Bisync, 12 Bits
SDLC0
Sync6
Sync4
Sync14
Sync10
1
Sync5
Sync3
Sync13
Sync9
1
Sync4
Sync2
Sync12
Sync8
1
Sync3
Sync1
Sync11
Sync7
1
Sync2
Sync0
Sync10
Sync6
1
Sync1
x
Sync9
Sync5
1
Sync0
x
Sync8
Sync4
0
D7 D6 D5 D4 D3 D2 D1 D0
WR 7’ Prime (85C30 only)
Auto Tx Flag
Auto EOM Reset
Auto R TS Deactivation
Force TxD High
DTR/REQ Fast Mode
Complete CRC Reception
Extended Read Enable
Reserved (Program as 0)
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
36
Figure 18. Write Register Bit Functions
0
0
0
01
1
11
D7 D6 D5 D4 D3 D2 D1 D0
Write Register 9
No Reset
Channel Reset B
Channel Reset A
Force Hardware Reset
VIS
NV
DLC
MIE
S t atus High/Status Low
Software INTACK Enable
D7 D6 D5 D4 D3 D2 D1 D0
Write Register 10
0
0
0
01
1
11
NRZ
NRZI
FM1 (Transition = 1)
FM1 (Transition = 0)
CRC Preset I/O
Go Active on Pol l
Mark/Flag Idle
Abort/Flag on Underrun
Loop Mode
6-Bit/8- B i t Sync
D7 D6 D5 D4 D3 D2 D1 D0
Write Register 11
0
0
0
01
1
11
0
0
0
01
1
11
0
0
0
01
1
11
TRxC Out = Xtal Output
TRxC Out = Transmit Clock
TRxC Out = BR Generator Output
TRxC Out = DPLL Output
TRxC O/I
Tr a n smit Cloc k = RTxC Pin
Transmit Clock = TRxC Pin
Transmit Clock = BR Generator Output
Transmit Clock = DPLL Output
Receive Clock = RTxC Pin
Receive Clock = TRxC Pin
Receive Clock = BR Generator Output
Receive Clock = DPLL Output
RTxC Xtal/No Xtal
D7 D6 D5 D4 D3 D2 D1 D0
Write Register 12
TC0
TC1
TC2
TC3
TC4
TC5
TC6
TC7
Lower Byte of
T ime Constant
Upper Byte of
Time Const ant
D7 D6 D5 D4 D3 D2 D1 D0
Write Register 13
TC8
TC9
TC10
TC11
TC12
TC13
TC14
TC15
D7 D6 D5 D4 D3 D2 D1 D0
Write Register 14
BR Generator Enable
BR Generator Source
DTR/Request Function
Auto Echo
Local Loopback
0
0
0
0
01
1
0
0
00
0
0
0
1
11
11
1
1
1
1
1
Null Command
Enter Search Mode
Reset Missing Clock
Disable DPLL
Set Source = BR Generator
Set Source = RTxC
Set FM Mode
Set NRZI Mode
D7 D6 D5 D4 D3 D2 D1 D0
Write Register 15
0
Zero Count IE
SDLC FIFO Enable
DCD IE
Sync/Hunt IE
CTS IE
Tx Underrun/EOM IE
Break/Abort IE
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
37
Read Registers
The SCC contains ten Read registers (eleven, counting the receive buffer (RR8) in each
channel). Four of these can be read to obtain status information (RR0, RR1, RR10, and
RR15). Two registers (RR12 and RR13) are read to learn the Baud Rate Generator time
constant. RR2 contains either the unmodified interrupt vector (Channel A) or the vect or
modified by status information (Channel B). RR3 contains the Interrupt Pending (IP) bits
(Channel A only; see Figure 19). RR6 and RR7 contain the information in the SDLC
Frame Status FIFO, but is only read when WR15 D2 is set (see Figures 19 and 20 ).
Figure 19. Read Register Bit Functions
D7 D6 D5 D4 D3 D2 D1 D0
Read Register 0
Rx Character Available
Zero Count
Tx Buffer Empty
DCD
Sync/Hunt
CTS
Tx Underrun/EOM
Break/Abort
D7 D6 D5 D4 D3 D2 D1 D0
Read Register 1
All Sent
Residue Code 2
Residue Code 1
Residue Code 0
Parity Error
Rx Overrun Error
CRC/Framing Error
End of Frame (SDLC)
D7 D6 D5 D4 D3 D2 D1 D0
Read Register 2
V0
V1
V2
V3
V4
V5
V6
V7
Interrupt
Vector *
* Modified in B Channel
D7 D6 D5 D4 D3 D2 D1 D0
Read Register 12
TC0
TC1
TC2
TC3
TC4
TC5
TC6
TC7
Lower Byte
of Time Constant
D7 D6 D5 D4 D3 D2 D1 D0
Read Register 10
0
On Loop
0
0
Loop Sending
0
Two Clocks Missing
One Clocks Missing
D7 D6 D5 D4 D3 D2 D1 D0
Read Register 3
Channel B Ext/Status IP
Channel B Tx IP
Channel B Rx IP
Channel A Ext/Status IP
Channel A Tx IP
Channel A Rx IP
0
0
*
* Always 0 in B Channel
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
38
Z85C30 Timing
The SCC generates internal control signals from the WR and RD that are related to PCLK.
PCLK has no phase relationship with WR and RD, the circuitry generating the internal
control signals provides time for meta-stable conditions to disappear. This gives rise to a
recovery time related to PCLK. The recovery time applies only between bus transactio ns
involving the SCC.
The recovery time required for proper operation is specified from the falling edge of WR
or RD in the first transaction involving the SCC to the falling edge of WR or RD in the
second transaction involving the SCC. This time must be at least 3 PCLKs regardless of
which register or channel is being accessed.
The Z85C30 timings are described below:
Read Cycle Timing
Write Cycle Timing
Interrupt Acknowledge Cycle Timing
Figure 20. Read Register Bit Functions
D7 D6 D5 D4 D3 D2 D1 D0
Read Register 13
TC8
TC9
TC10
TC11
TC12
TC13
TC14
TC15
Upper Byte
of Time Constant
D7 D6 D5 D4 D3 D2 D1 D0
Read Register 15
0
Zero Count IE
0
DCD IE
Sync/Hunt IE
CTS IE
Tx Underrun/EOM IE
Break/Abort IE
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
39
Read Cycle Ti ming
Figure 21 displays Read cycle timing. Addresses on A/ B and D/C and the status on
INTACK must remain stable throughout the cycle. If CE falls after RD falls, or if CE rises
before RD rises, the effective RD is shortened.
Figure 21. Read Cycle Timing
D7–D0 Data Valid
RD
CE
INTACK
A/
B, D/C
Address Valid
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
40
Write Cycle Timing
Figure 22 displays Write cycle timing. Addresses on A/B an d D/ C and the status on
INTACK must remain stable throughout the cycle. If CE falls after WR falls, or if CE rises
before WR rises, the effective WR is shortened. Data must be valid before the rising edge
of WR.
Interrupt Acknowledge Cycle Timing
Figure 23 displays an Interrupt Acknowledge cycle timing. Between the time INTACK
goes Low and the falling edge of RD, the internal and external IEI/IEO daisy chains settle.
If there is an interrupt pending in the SCC and IEI is High when RD falls, the Acknowl-
edge cycle is intended for the SCC. In this case, the SCC can be programmed to respond to
RD Low by placing its interrupt vector on D7-D0. It then sets the appropriate Interrupt-
Under-Service latch internally.
If the external daisy chain is not used, AC parameter #38 is required to settle the interrupt
priority daisy chain internal to the SCC. If the external daisy chain is used, you must fol-
low the equation in Table 6 on page 50 for calculating the required daisy-chain settle time.
Figure 22. Write Cycle Timing
Ad
Add
A Address Valid
Data Valid
WR
D7-D0
CE
INTACK
A/B, D/C
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
41
Z80C30 Timing
The SCC generates internal control signals from AS and DS that are related to PCLK.
Because PCLK has no phase relationship with AS and DS, the circuitry generating these
internal control signals must provide time for metastable cond itions to disappear. This
gives rise to a recovery time related to PCLK. The recovery time applies only between bus
transactions involving the SCC. The recovery time required for proper operation is speci-
fied from the falling edge of DS in the first transaction involving the SCC to the falling
edge of DS in the second transaction involving the SCC. The timings for Z80C30 device is
described below:
Read Cycle Timing
Write Cycle Timing
Interrupt Acknowledge Cycle Timing
Read Cycle Ti ming
Figure 24 displays the Read cycle timing. The address on AD7–AD0 and the state of CS0
and INTACK are latched by the rising edge of AS. R/W must be High to indicate a Read
cycle. CS1 must also be High for the Read cycle to occur. The data bus driver s in the SCC
are then enabled while DS is Low.
Figure 23. Interrupt Acknowledge Cycle Timing
D7–D0
RD
INTACK
Vector
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
42
Write Cycle Timing
Figure 25 displays the Write cycle timing. The address on AD7–AD0 and the state of
CS0
and INTACK are latched by the rising edge of
AS
. R/
W
must be Low to indicate a Write
cycle. CS1 must be High for the Write cycle to occur DS Low strobes the data into the
SCC.
Figure 24. Read Cycle Timing
INTACK
DS
AS
CS0
R/
W
CS1
AD7–AD0 Address Data Valid
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
43
Interrupt Acknowledge Cycle Timing
Figure 26 displays the Interrupt Ack nowledge cycle timing. The address on AD7 –AD0
and the state of CS0 and INTACK are latched by the rising edge of AS. If INTACK is
Low, the address and CS0 are ignored. The state of the R/W and CS1 are also ignored for
the duration of the Interrupt Acknowledge cycle. Between the rising edge of AS and the
falling edge of DS, the internal and external IEI/IEO daisy chains settle. If there is an
interrupt pending in the SCC, and IEI is High when DS falls, the Acknowledge cycle was
intended for the SCC. In this case, the SCC is programmed to respond t o RD Low by plac-
ing its interrupt vector on D7-D0 and internally setting the appropriate Interrupt-Under-
Service latch.
Figure 25. Write Cycle Timing
INTACK
DS
AS
CS0
R/W
CS1
AD7–AD0 Address Data
PS011706-0511 Functional Descriptions
CMOS SCC Serial Communications Controller
Product Specification
44
Figure 26. Interrupt Acknowledge Cycle Timing
AD7–AD0
DS
(Ignored)
(Ignored) Vector
AS
CS0
INTACK
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
45
Electrical Characteristics
The electrical cha rac te ris tic s of the Z80 C 30 and the Z85C30 devices are described in the
following sections.
Absolute Maximum Ratings
Stresses greater than those listed in Table 3 may cause permanent damage to the device
This is a stress rating only. Operation of the device at any condition above those indicated
in the operational sections of these specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
Standard Test Conditions
The DC Characteristics and capacitance sections below apply for the following standard
test conditions, unless otherwise noted. All voltages are referenced to GND. Positive cur-
rent flows into the referenced pin. See Figure 27 and Figure 28.
+4.50 V Vcc + 5.50 V
GND = 0 V
TA (see Ordering Information)
Table 3. Absolute Maximum Ratings
Vcc Supply Voltage range –0.3 V to +7.0 V
Voltages on all pins with respect to GND –3 V to VCC +0.3 V
TA Operating Ambient Temperature See Ordering Information
Storage Temperature –65° C to +150° C
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
46
39
Figure 27. Standard Test Load
Figure 28. Open-Drain Test Load
+5 V
100 pF 250 A
2.1 K
From Output
Under Test
From Output
+5 V
50 pF
2.2 K
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
47
Capacitance
Table 4 lists the input, output and bidirectional capacitance.
Miscellaneous
The Gate Count is 6800.
DC Characteristics
Table 5 lists the DC characteristics for the Z80C30 and Z85C30 devices.
Table 4. Cap acitance
Symbol Parameter Min Max Unit Test Condition
CIN Input Capacitance 10 pF1Unmeasured Pins Returned to Ground2
COUT Output Capacitance 15 pF
CI/O Bidirectional Capacitance 20 pF
Notes:
1. pF = 1 MHz, over specified temperature range.
2. Unmeasured pins returned to Ground.
Table 5. Z80C30/Z85C30 DC Characteristics
Symbol Parameter Min Typ Max Unit Condition
VIH Input High Voltage 2.2 VCC +0.31V
VIL Input Low Voltage –0.3 0.8 V
VOH1 Output High Voltage 2.4 V IOH = –1.6 mA
VOH2 Output High Voltage VCC – 0.8 V IOH = –250 A
VOL Output Low Voltage 0.4 V IOL = +2.0 mA
IIL Input Leakage 10.0 A0.4 V
IN + 2.4 V
IOL Output Leakage 10.0 A0.4 V
OUT + 2.4 V
ICC1 VCC Supply Current27 12 (10 MHz) mA VCC = 5 V; VIH = 4.8 VIL = 0
9 15 (16.384 MHz) mA Crystal Oscillator off
ICCOSC Crystal OSC Current34 mA Current for each OSC in
addition to ICC1
Notes:
1. VCC = SV t10% unless otherwise specified, over specified temperature range.
2. Typi cal ICC was measured with oscillator off.
3. No ICC (OSC) max is specified due to dependency on external circuit and frequency of oscillation.
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
48
AC Characteristics
Figures 29 through 32 display Read and Write timing for the Z85C30 device.
Figure 29. Z85C30 Read/Write Timing Diagram
PCLK
A/B, D/C
INTACK
CE
RD
D7–D0
Read
WR
D7–D0
Write
W/REQ
Wait
W/REQ
Request
DTR/REQ
Request
INT
6
1
2
5
11
13
10
16
19 22
Active Valid
23
25
27
28
31
29
32
33
34
37
35
36
24 26 17
20
30
34
710
15
18
12
14
9
21
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
49
Figure 30. Z85C30 Interrupt Acknowledge Timing Diagram
Figure 31. Z85C30 Cycle Timing Diagram
D7–D0
INT
PCLK
INTACK
RD
IEI
IEO
41
38
10
23
Active Valid
10
14
24
26
42
40
38
15
45
44
43
CE
49b 49b
49a
PCLK
or WR
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
50
Table 6 lists the Read/Write timing parameters for the Z85C30 device.
Figure 32. Z85C30 Reset Timing Diagram
Table 6. Z85C30 Read/Write Timing
No Symbol Parameter
8.5 MHz 10 MHz 16 MHz
Min Max Min Max Min Max
1 TwPCI PCLK Low Width 45 2000 40 2000 26 2000
2 TwPCh PCLK High Width 45 2000 40 2000 26 2000
3 TfPC PCLK Fall Time 10 10 5
4 TrPC PCLK Rise Time 10 10 5
5 TcPC PCLK Cycle Time 118 4000 100 4000 61 4000
6 TsA(WR) Address to WR Fall
Setup Time 66 50 35
7 ThA(WR) Address to WR Rise
Hold Time 000
8 TsA(RD) Address to RD Fall
Setup Time 66 50 35
9 ThA(RD) Address to RD Rise
Hold Time 000
Notes:
1. Parameter does not apply to Interrupt Acknowledge transactions.
2. Open-drain output, measured with open-drain test load.
3. Parameter applies to enhanced Request mode oniy (WR7’ D4 = 1).
4. Parameter is system-dependent. For any SCC in the daisy chain, TdIAi(RD) must be gre ate r than the sum of
TdPC(IEO) for the highest priority device in the daisy chain. TsiEI(RDA) for the SCC and TdIEI(IEO) for each
device separating them in th e da i sy cha i n.
5. Parameter applies only between transa ctions involving the Z85C30 SL1480, if WR/RD falling edge is synchro-
nized to PCLK falling edge, then TrC = 3TcPc.
6. This specification is only applicable when Valid Access Recovery Time is less than 35 PCLK.
48
RD
WR
47 48
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
51
10 TsiA(PC) INTACK to PCLK Rise
Setup Time 20 20 15
11 TsiAi(WR)1INTACK to WR Fall
Setup Time 140 120 70
12 ThIA(WR) INTACK to WR Rise
Hold Time 00 0
13 TsiAi(RD)1INTACK to RD Fall
Setup Time 140 120 70
14 ThIA(RD) INTACK to RD Rise
Hold Time 00 0
15 ThIA(PC) INTACK to PCLK Rise
Hold Time 38 30 15
16 TsCEI(WR) CE Low to WR Fall
Setup Time 00 0
17 ThCE(WR) CE to WR Rise Hold
Time 00 0
18 TsCEh(WR) CE High to WR Fall
Setup Time 58 50 30
19 TsCEI(RD)1CE Low to RD Fall
Setup Time 000
20 ThCE(RD)1CE to RD Rise Hold
Time 000
21 TsCEh(RD)1CE High to RD Fall
Setup Time 58 50 30
22 TwRDI1RD Low Width 145 125 70
Table 6. Z85C30 Read/Write Timing (continued)
No Symbol Parameter
8.5 MHz 10 MHz 16 MHz
Min Max Min Max Min Max
Notes:
1. Parameter does not apply to Interrupt Acknowledge transactions.
2. Open-drain output, measured with open-drain test load.
3. Parameter applies to enhanced Request mode oniy (WR7’ D4 = 1).
4. Parameter is system-dependent. For any SCC in the daisy chain, TdIAi(RD) must be gre ate r than the sum of
TdPC(IEO) for the highest priority device in the daisy chain. TsiEI(RDA) for the SCC and TdIEI(IEO) for each
device separating them in th e da i sy cha i n.
5. Parameter applies only between transa ctions involving the Z85C30 SL1480, if WR/RD falling edge is synchro-
nized to PCLK falling edge, then TrC = 3TcPc.
6. This specification is only applicable when Valid Access Recovery Time is less than 35 PCLK.
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
52
23 TdRD(DRA) RD Fall to Read Data
Active Delay 000
24 TdRDr(DR) RD Rise to Data Not
Valid Delay 000
25 TdRDI(DR) RD Fall to Read Data
Valid Delay 135 120 70
26 TdRD(DRz) RD Rise to Read Data
Float Delay 38 35 30
27 TdA(DR) Addr to Read Data
Valid Delay 210 160 100
28 TwWRI WR Low Width 145 125 75
29 TdWR(DW) WR Fall to Write Data
Valid Delay 35 35 20
30 ThDW(WR) Write Data to WR Rise
Hold Time 00 0
31 TdWR(W)2WR Fall to Wait Valid
Delay 168 100 50
32 TdRD(W)2RD Fall to Wait Valid
Delay 168 100 50
33 TdWRf(REQ) WR Fall to W/REQ Not
Valid Delay 168 120 70
34 TdRDf(REQ)3RD Fall to W/REQ Not
Valid Delay 168 120 70
35a TdWRr(REQ) WR Fall to DTR/REQ
Not Valid 4TcPc 4TcPc 4TcPc
Table 6. Z85C30 Read/Write Timing (continued)
No Symbol Parameter
8.5 MHz 10 MHz 16 MHz
Min Max Min Max Min Max
Notes:
1. Parameter does not apply to Interrupt Acknowledge transactions.
2. Open-drain output, measured with open-drain test load.
3. Parameter applies to enhanced Request mode oniy (WR7’ D4 = 1).
4. Parameter is system-dependent. For any SCC in the daisy chain, TdIAi(RD) must be gre ate r than the sum of
TdPC(IEO) for the highest priority device in the daisy chain. TsiEI(RDA) for the SCC and TdIEI(IEO) for each
device separating them in th e da i sy cha i n.
5. Parameter applies only between transa ctions involving the Z85C30 SL1480, if WR/RD falling edge is synchro-
nized to PCLK falling edge, then TrC = 3TcPc.
6. This specification is only applicable when Valid Access Recovery Time is less than 35 PCLK.
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
53
35b TdWRr(REQ)3WR Fall to DTR/REQ
Not Valid 168 100 70
36 TdRDrrREQ) RD Rise to DTR/REQ
Not Valid Delay NA NA NA
37 TdPC(INT) PCLK Fall to INT Valid
Delay 500 320 175
38 TdIAi(RD)4INTACK to RD Fall
(Ack) Delay 145 90 50
39 TwRDA RD (Acknowledge)
Width 145 125 75
40 TdRDA(DR) RD Fall (Ack) to Read
Data Valid Delay 135 120 70
41 TsiEI(RDA) IEI to RD Fall (Ack)
Setup Time 95 80 50
42 ThIEI(RDA) IEI to RD Rise (Ack)
Hold Time 0 0 0
43 TdIElrIEO) IEI to IEO Delay Time 95 80 45
44 TdPC(IEO) PCLK Rise to IEO
Delay 195 175 80
45 TdRDA(INT)2RD Fall to INT Inactive
Delay 480 320 200
46 TdRDrWRQ) RD Rise to WR Fall
Delay for No Reset 15 15 10
47 TdWRQ(RD) WR Rise to RD Fall
Delay for No Reset 15 15 10
Table 6. Z85C30 Read/Write Timing (continued)
No Symbol Parameter
8.5 MHz 10 MHz 16 MHz
Min Max Min Max Min Max
Notes:
1. Parameter does not apply to Interrupt Acknowledge transactions.
2. Open-drain output, measured with open-drain test load.
3. Parameter applies to enhanced Request mode oniy (WR7’ D4 = 1).
4. Parameter is system-dependent. For any SCC in the daisy chain, TdIAi(RD) must be gre ate r than the sum of
TdPC(IEO) for the highest priority device in the daisy chain. TsiEI(RDA) for the SCC and TdIEI(IEO) for each
device separating them in th e da i sy cha i n.
5. Parameter applies only between transa ctions involving the Z85C30 SL1480, if WR/RD falling edge is synchro-
nized to PCLK falling edge, then TrC = 3TcPc.
6. This specification is only applicable when Valid Access Recovery Time is less than 35 PCLK.
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
54
48 TwRES WR and RD Low for
Reset 145 100 75
49a TrceValid Access Recovery
Time 3.5TcPc 3.5TcPc 3.5TcPc
49b TrcifRD or WR Fall to PC
Fall Setup Time 0 0 0
Table 6. Z85C30 Read/Write Timing (continued)
No Symbol Parameter
8.5 MHz 10 MHz 16 MHz
Min Max Min Max Min Max
Notes:
1. Parameter does not apply to Interrupt Acknowledge transactions.
2. Open-drain output, measured with open-drain test load.
3. Parameter applies to enhanced Request mode oniy (WR7’ D4 = 1).
4. Parameter is system-dependent. For any SCC in the daisy chain, TdIAi(RD) must be gre ate r than the sum of
TdPC(IEO) for the highest priority device in the daisy chain. TsiEI(RDA) for the SCC and TdIEI(IEO) for each
device separating them in th e da i sy cha i n.
5. Parameter applies only between transa ctions involving the Z85C30 SL1480, if WR/RD falling edge is synchro-
nized to PCLK falling edge, then TrC = 3TcPc.
6. This specification is only applicable when Valid Access Recovery Time is less than 35 PCLK.
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
55
Figure 33 displays a general timing diag ram for the Z85C30 device.
Figure 33. Z85C30 General Timing Diagram
SYNC
Input
CTS/TRxC
DCD
CTS/TRxC
RTxC
CTS/TRxC
Output
22 22
22 22
20
18 19
16
17
14 15
1
2
67
45
89
3
12
11
13
TxD
RTxC
Transmit
CTS/TRxC,
SYNC
External
10
RxD
RTxC
Receive
CTS/TRxC,
W/REQ
Wait
W/REQ
Request
PCLK
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
56
Table 7 lists the general timing characteristics for the Z85C30 device.
Table 7. Z85C30 General Timing Table
No Symbol Parameter
8.5 MHz 10 MHz 16 MHz
Min Max Min Max Min Max
1 TdPC(REQ) PCLK to W/REQ Valid 250 150 80
2 TdPC(W) PCLK to Wait Inactive 350 250 180
3 TsRXC(PC) RxC to PCLK Setup Time1,2 N/A N/A N/A
4 TsRXD(RXCr) RxD to RxC Setup Time10 0 0
5 ThRXD(RxCr) RxD to /RXC Hold Time1150 125 50
6 TsRXD(RXCf) RxD to /RXC Setup Time1,3 0 0 0
7 ThRXD(RXCf) RxD to /RXC Hold Time1,3 150 1 25 50
8 TsSY(RXC) SYNC to RxC Setup Time1–200 –150 –100
9 ThSY(RXC) SYNC to RxC Hold Time15TcPc 5TcPc 5TcPc
10 TsTXC(PC) TxC to PCLK Setup Time4,5 N/A N/A N/A
11 TdTXCf(TXD) TxC to TxD Delay4200 150 80
12 TdTxCr(TXD) TxC to TxD Delay3,4 200 150 80
13 TdTXD(TRX) TxD to TRxC Delay 200 140 80
14a TwRTXh RTxC High Width6150 120 80
14b TwRTXh(E) RTxC High Width750 40 15.6
15a TwRTXI TRxC Low Width6150 120 80
15b TwRTXI(E) RTxC Low Width750 40 15.6
16a TcRTX RTxC Cycle Time6,8 488 400 244
16b TcRTX(E) RTxC Cycle Time7125 100 31.25
17 TcR TXX Crystal Osc. Period9125 1000 100 1000 62 1000
18 TwTRXh TRxC High Width6150 120 180
Notes:
1. RxC is RTxC or TRxC, whichever is supplying the receive clock.
2. Synchronization of RxC to PCLK is eliminated in divide by four operation.
3. Parameter applies only to FM encodin g/decoding.
4. TxC is TRxC or /R TxC, whichever is supplying the transmit clock.
5. External PCLK to R TxC or TxC synchronization requirement eliminated for PCLK divide-by-four operation.TRxC
and RTxC rise and fall times are identical to PCLK. Reference timing specs TfPC and TrPC.Tx and Rx input
clock slew rates should be kept to a maximum of 30 nsec. All parameters related to input CLK edges must be
referenced at the point at which the transition begins or end s, whichever is worst case.
6. Parameter applies only for transmitte r and receiver; DPLL and Baud Rate Generator timing requirements are
identical to case PCLK requirements.
7. Enhanced Feature — RTxC used as input to internal DPLL only.
8. The maximum receive or transmit data rate is 1/4 PCLK.
9. Both RTxC and SYNC have 30 pF capacitors to ground connections.
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
57
19 TwTRXI TRxC Low Width6150 120 80
20 TcTRX TRxC Cycle Time6,8 488 400 244
21 TwEXT DCD or CTS Pulse Width 200 120 70
22 TwSY SYNC Pulse Width 200 120 70
Table 7. Z85C30 General Timing Table (continued)
No Symbol Parameter
8.5 MHz 10 MHz 16 MHz
Min Max Min Max Min Max
Notes:
1. RxC is RTxC or TRxC, whichever is supplying the receive clock.
2. Synchronization of RxC to PCLK is eliminated in divide by four operation.
3. Parameter applies only to FM encodin g/decoding.
4. TxC is TRxC or /R TxC, whichever is supplying the transmit clock.
5. External PCLK to R TxC or TxC synchronization requirement eliminated for PCLK divide-by-four operation.TRxC
and RTxC rise and fall times are identical to PCLK. Reference timing specs TfPC and TrPC.Tx and Rx input
clock slew rates should be kept to a maximum of 30 nsec. All parameters related to input CLK edges must be
referenced at the point at which the transition begins or end s, whichever is worst case.
6. Parameter applies only for transmitte r and receiver; DPLL and Baud Rate Generator timing requirements are
identical to case PCLK requirements.
7. Enhanced Feature — RTxC used as input to internal DPLL only.
8. The maximum receive or transmit data rate is 1/4 PCLK.
9. Both RTxC and SYNC have 30 pF capacitors to ground connections.
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
58
Figure 34 displays the system timing for the Z85C30 device.
Figure 34. Z85C30 System Timing Diagram
10
INT
SYNC
Input
INT
CTS
, DCD
DTR
/REQ
Request
Wait
W
/REQ
Request
W
/REQ
TRxC
, R T xC
Transmit
INT
SYNC
Output
Wait
W
/REQ
Request
W
/REQ
RTxC
, TRxC
Receive
9
8
7
6
6
4
3
1
2
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
59
Table 8 lists the system timing characteristics for the Z85C30 device.
Table 9 provides the Read/Write timing characteristics for the Z85C30 device.
Table 8. Z85C30 System Timing Table
No Symbol Parameter
8.5 MHz 10 MHz 16 MHz
Min Max Min Max Min Max
1 TdRXC(REQ) RxC High to W/REQ Valid1,2 8 12 8 12 8 12
2 TdRXC(W) RxC High to Wait Inactive1,2,3 8 14 8 14 8 14
3 TdRdXC(SY) RxC High to SYNC Valid1,2 4747470
4 TsRXC(INT) RxC High to INT Valid1,2,3 10 16 10 16 10 16
5 TdTXC(REQ) TxC Low to W/REQ Valid2,4 5 8 5 8 5 8
6 TdTXC(W) TxC Low to Wait Inactive2,3,4 5 11 5 11 5 11
7 TdTXC(DRQ) TxC Low to DTR/REQ Valid3,4 4 7 4 7 4 7
8 TdTXC(INT) TxC Low to INT Valid2,3,4 6 10 6 10 6 10
9a TdSY(INT) SYNC to INT Valid 2,3 2 6 2 6 2 6
9b TdSY(INT) SYNC to INT Valid2,3,5 2 3 2 3 2 3
10 TdEXT(INT) DCD or CTS to INT Valid2,3 2 6 2 6 2 6
Notes:
1. RxC is RTxC or TR xC, whichever is supplying the receive clock.
2. Units equal to TcPc.
3. Open-drain output, measured with open-drain test load.
4. TxC is TRxC or RTxC whichever is supplying the transmit clock.
5. Units equal to AS.
Table 9. Z85C30 Read/Write Timing
No Symbol Parameter
8.5 MHz 10 MHz 16 MHz
Min Max Min Max Min Max
1 TwPCI PCLK Low Width 45 2000 40 2000 26 2000
2 TwPCh PCLK High Width 45 2000 40 2000 26 2000
3 TfPC PCLK Fail Time 10 10 5
4 TrPC PCLK Rise Time 10 10 5
5 TcPC PCLK Cycle Time 118 4000 100 4000 61 4000
6 TsA(WR) Address to WR Fail Setup Time 66 50 35
7 ThA(WR) Address to WR Rise Hold Time 0 0 0
8 TsA(RD) Address to RD Fall Setup Time 66 50 35
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
60
9 ThA(RD) Address to RD Rise Hold Time 0 0 0
10 TsiA(PC) INTACK to PCLK Rise Setup Time 20 20 15
Table 9. Z85C30 Read/Write Timing (continued)
No Symbol Parameter
8.5 MHz 10 MHz 16 MHz
Min Max Min Max Min Max
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
61
Figures 35 through 37 display the Read/Write timing, interrupt acknowledge timing and
reset timing, respectively, for the Z80C30 device.
Figure 35. Z80C30 Read/Write Timing Diagram
Wait
W/REQ
Request
PCLK
42
40 41
43 44
44
27
INT
DTR/REQ
Request
W/REQ
25
26
24 22
15
15 16 17
16
12 13
1921
AD7–AD0
Read
AD7–AD0
Write
DS
12
Write
R/W
Write
R/W
Read
INTACK
78
9
CS1
CS0
7
4
414 6
10
10
18
20
23
2
AS
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
62
Figure 36. Z80C30 Interrupt Acknowledge Timing Diagram
Figure 37. Z80C30 Reset Timing Diagram
INT
IEO
IEI
36
35
34
32 31 22
33
20
30
19
29
8
7
AD7–AD0
DS
INTACK
AS
DS
AS 37 38 35
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
63
Table 10 provides the Read/Write timing ch aracteristics for the Z80 C30 device.
Table 10. Z80C30 Read/Write Timing1
No Symbol Parameter
8 MHz 10 MHz
Min Max Min Max
1 TwAS AS Low Width 35 30
2 TdDS(AS) DS Rise to AS Fall Delay215 10
3 TsCSO(AS) CS0 to AS Rise Setup Time20 0
4 ThCSO(AS) CS0 to AS Rise Hold Time230 20
5 TsCS1(DS) CS1 to DS Fall Setup Time265 50
6 ThCS1(DS) CS1 to DS Rise Hold Time230 20
7 TsiA(AS) INTACK to AS Rise Setup Time 10 10
8 ThIA(AS) INTACK to AS Rise Hold Time 150 125
9 TsRWR(DS) R/W (Read) to DS Fall Setup Time 65 50
10 ThRW(DS) R/W to DS Rise Hold Time 0 0
11 TsRWW(DS) R/W (Write) to DS Fall Setup Time 0 0
12 TdAS(DS) AS Rise to DS Fall Delay 30 20
13 TwDSI DS Low Width 150 125
14 TrC Valid Access Recovery Time34TcPC 4TcPC
15 TsA(AS) Address to AS Rise Setup Time210 10
16 ThA(AS) Address to AS Rise Hold Time225 20
17 TsDW(DS) Write Data to DS Fall Setup Time 15 10
18 ThDW(DS) Write Data to DS Rise Hold Time 0 0
19 TdDS(DA) DS Fall to Data Active Delay 0 0
20 TdDSr(DR) DS Rise to Read Data Not Valid Delay 0 0
21 TdDSf(DR) DS Fall to Read Data Valid Delay 140 120
22 TdAS(DR) AS Rise to Read Data Valid Delay 250 190
Notes:
1. Units in nanoseconds (ns) unless otherwise noted.
2. Parameter does not apply to Interrupt Acknowledge transactions.
3. Parameter applies only between tran sactions involving the SCC.
4. Float delay is defined as the time required for a 0.5 V change in the output with a maximum DC load and a min-
imum AC load.
5. Open-drain output, measured with open-drain test load.
6. Parameter is system dependent. For any Z-SCC in the daisy chain. TdAS(DSA) must be greater than the sum of
TdAS(IEO) for the highest priority device in the daisy chain TsiEI(DSA) for the Z-SC C, and TdIElf(IEO) for each
device separating them in th e da i sy cha i n.
7. Parameter applies only to a Z-SCC pulling INT Low at the beginning of the Interrupt Acknowledge transaction.
8. Internal circuitry allows for the reset provided by the ZB to be recognized as a reset by the Z-SCC. All timing ref-
erences assume 20 V for a logic “1” and 08 V for a logic “0 ”.
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
64
23 TdDS(DRz) DS Rise to Read Data Float Delay440 35
24 TdA(DR) Address Required Valid to Read Data
Valid Delay 260 210
25 TdDS(W) DS Fall to Wait Valid Delay5170 160
26 TdDSf(REQ) DS Fall to W/REQ Not Valid Delay 170 160
27 TdDSr(REQ) DS Fall to DTR/REQ Not Valid Delay 4TcPC 4TcPC
28 TdAS(INT) AS Rise to INT Valid Delay5500 500
29 TdAS(DSA) AS Rise to DS Fall (Acknowledge)
Delay6250 225
30 TwDSA DS (Acknowledge) Low Width 150 125
31 TdDSA(DR) DS Fall (Acknowledge) to Read Data
Valid Delay 140 120
32 TsiEI(DSA) IEI to DS Fall (Acknowledge) Setup
Time 80 80
33 ThIEI(DSA) IEI to DS Rise (Acknowledge) Hold
Time 0 0
34 TdIEI(IEO) IEI to IEO Delay 90 90
35 TdAS(IEO) AS Rise to IEO Delayg200 175
36 TdDSA(INT) DS Fall (Acknowledge) to INT Inactive
Delay5450 450
37 TdDS(ASQ) DS Rise to AS Fall Delay for No Reset 15 15
38 TdASQ(DS) AS Rise to DS Fall Delay for No Reset 20 15
39 TwRES AS and DS Coincident Low for Reseth150 100
40 TwPCI PCLK Low Width 50 1000 40 1000
Table 10. Z80C30 Read/Write Timing1 (continued)
No Symbol Parameter
8 MHz 10 MHz
Min Max Min Max
Notes:
1. Units in nanoseconds (ns) unless otherwise noted.
2. Parameter does not apply to Interrupt Acknowledge transactions.
3. Parameter applies only between tran sactions involving the SCC.
4. Float delay is defined as the time required for a 0.5 V change in the output with a maximum DC load and a min-
imum AC load.
5. Open-drain output, measured with open-drain test load.
6. Parameter is system dependent. For any Z-SCC in the daisy chain. TdAS(DSA) must be greater than the sum of
TdAS(IEO) for the highest priority device in the daisy chain TsiEI(DSA) for the Z-SC C, and TdIElf(IEO) for each
device separating them in th e da i sy cha i n.
7. Parameter applies only to a Z-SCC pulling INT Low at the beginning of the Interrupt Acknowledge transaction.
8. Internal circuitry allows for the reset provided by the ZB to be recognized as a reset by the Z-SCC. All timing ref-
erences assume 20 V for a logic “1” and 08 V for a logic “0 ”.
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
65
41 TwPCh PCLK High Width 50 1000 40 1000
42 TcPC PCLK Cycle Time 125 2000 100 2000
43 TrPC PCLK Rise Time 10 10
44 TfPC PCLK Fall Time 10 10
Table 10. Z80C30 Read/Write Timing1 (continued)
No Symbol Parameter
8 MHz 10 MHz
Min Max Min Max
Notes:
1. Units in nanoseconds (ns) unless otherwise noted.
2. Parameter does not apply to Interrupt Acknowledge transactions.
3. Parameter applies only between tran sactions involving the SCC.
4. Float delay is defined as the time required for a 0.5 V change in the output with a maximum DC load and a min-
imum AC load.
5. Open-drain output, measured with open-drain test load.
6. Parameter is system dependent. For any Z-SCC in the daisy chain. TdAS(DSA) must be greater than the sum of
TdAS(IEO) for the highest priority device in the daisy chain TsiEI(DSA) for the Z-SC C, and TdIElf(IEO) for each
device separating them in th e da i sy cha i n.
7. Parameter applies only to a Z-SCC pulling INT Low at the beginning of the Interrupt Acknowledge transaction.
8. Internal circuitry allows for the reset provided by the ZB to be recognized as a reset by the Z-SCC. All timing ref-
erences assume 20 V for a logic “1” and 08 V for a logic “0 ”.
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
66
Figure 38 displays a general timing diagram for the Z80C30 device, and Table 11 lists its
associated general timing characteristics.
Figure 38. Z80C30 General Timing Diagram
SYNC
Input
22 22
22 22
CTS, DCD
TRxC
RTxC
TRxC
Output
TRxC, RTxC
Transmit
SYNC
External
RxD
RTxC, TRxC
Receive
W/REQ
Wait
W/REQ
Request
PCLK
20 19
18
16
17
14 15
13
8
11
10
9
456
3
7
1
2
12
TxD
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
67
Table 11. Z80C30 General Timing1
No Symbol Parameter
8 MHz 10 MHz
Min Max Min Max
1TdPC(REQ) PCLK
Low to W/REQ Valid 250 200
2TsPC(W) PCLK
Low to Wait Inactive 350 300
3 TsRXC(PC) RxC High to PCLK High Setup Time2,3 NA NA NA NA
4 TsRXD(RXCr) RxD to RxC High Setup Time 0 0
5 ThRXD(RxCr) RxD to RxC High Hold Time2150 125
6 TsRXD(RXCf) RxD to RxC Low Setup Time2,4 0 0
7 ThRXD(RXCf) RxD to RxC Low Hold Time2,4 150 125
8 TsSY(RXC) SYNC to RxC High Setup Time2-200 -150
9 ThSY(RXC) SYNC to RxC High Hold Time25TcPc 5TcPc
10 TsTXC(PC) TxC Low to PCLK High Setup Time3,5 NA NA
11 TdTXCf(TXD) TxC Low to TxD Delay5190 150
12 TdTxCr(TXD) TxC High to TxD Delay4,5 190 150
13 TdTXD(TRX) TxD to TRxC Delay 200 140
14 TwRTXh RTxC High Width6130 120
15 TwRTXI TRxC Low Width6130 120
16a TcRTX RTxC Cycle Time6,7 472 400
16b TxRx (DPLL) DPLL Cycle Time Min7,8 59 50
17 TcRTXX Crystal Os c. Period 9118 1000 100 1000
18 TwTRXh TRxC High Width6130 120
19 TwTRXI TRxC Low Width6130 120
20 TcTRX TRxC Cycle Time6,7 472 400
21 TwEXT DCD or CTS Pulse Width 200 120
22 TwSY SYNC Pulse Width 200 120
Notes:
1. Units in nanoseconds (ns) otherwise noted.
2. RxC is RTxC or (TRxC, whichever is supplying the receive clock.
3. Synchronization of RxC to PCLK is eliminated in divide by four operation.
4. Parameter applies only to FM encodin g/decoding.
5. TxC is TRxC or RTxC, whichever is supplying the transmit clock.
6. Parameter applies only for transmitte r and receiver; DPLL and Baud Rate Generator timing requirements are
identical to case PCLK requirements.
7. The maximum receive or transmit data rate is 1/4 PCLK.
8. Applies to DPLL clock source oniy Maximum data rate of 1/4 PCLK still applies DPLL clock should have a 50%
duty cycle.
9. Both RTxC and SYNC have 30 pf capacitors to ground connected to them.
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
68
Figure 39 displays a system timing diagram for the Z80C30 device, and Table 12 lists its
associated parameters.
Figure 39. Z80C30 System Timing Diagram
SYNC
Input
CTS, DCD
TRxC
RTxC
TRxC
Output
TxD
TRxC, RTxC
Transmit
SYNC
External
22 22
21 21
20
18 19
17
18
14 15
11
10
12
RxD
10
RTxC, TRxC
Receive
W/REQ
Wait
9
8
45
3
W/REQ
Request
PCLK
67
2
1
PS011706-0511 Electrical Characteristics
CMOS SCC Serial Communications Controller
Product Specification
69
Table 12. Z80C30 System Timing
No Symbol Parameter
8 MHz 10 MHz
Min Max Min Max
1 TdRXC(REQ) RxC High to W/REQ Valid1,2 812812
2 TdRXC(W) RxC High to Wait Inactive1,2,3 814814
3 TdRdXC(SY) RxC High to SYNC Valid1,2 4747
4 TdRXC(INT) RxC
High to INT Valid1,2,3 812812
24342434
5 TdTXC(REQ) TxC Low to W/REQ Valide,2 5858
6 TdTXC(W) TxC Low to Wait Inactive1,2,3 511511
7 TdTXC(DRQ) TxC Low to DTR/REQ Valid2,3 4747
8 TdTXC(INT) TxC Low to INT Valid1,2 4646
24342434
9a TdSY(INT) SYNC to INT Valid2,3 2626
9b TdSY(INT) SYNC to INT Valid2,3,4 2323
10 TdEXT(INT) Note2,3,4 2323
Notes:
1. RxC is RTxC or TR xC whichever is supplying the receive clock.
2. Units equal to TcPc.
3. Open-drain output, measured with open-drain test load.
4. Units equal to AS.
5. TxC is TRxC or RTxC, whichever is supplying the transmit clock.
PS011706-0511 Packaging
CMOS SCC Serial Communications Controller
Product Specification
70
Packaging
Figure 40 displays the 40-pin DIP package available for the Z80C30 and Z85C30 devices.
Figure 40. 40-Pin DIP Package Diagram
PS011706-0511 Packaging
CMOS SCC Serial Communications Controller
Product Specification
71
Figure 41 displays the 44-pin Plastic Leaded Chip Carriers (PLCC) package diagram
available for Z80C30 and Z85C30 devices.
Figure 41. 44-Pin PLCC Package Diagram
PS011706-0511 Ordering Information
CMOS SCC Serial Communications Controller
Product Specification
72
Ordering Information
Table 13 provides ordering information for the Z80C30 and the Z85C30 devices.
For complete details about Zilog’s Z80C30 and Z85C30 devices, development tools and
downloadable software, visit www.zilog.com.
Part Number Suffix Designations
Zilog part numbers consist of a number of components, as indicated in the following
example:
Part number Z80C3016PSG is a Z80C30, 16 MHz, PLCC, 0º C to +70º C, Lead Free
Table 13. Z80C30/Z85C30 Ordering Information
8 MHz 10 MHz 16 MHz
Z80C3008PSG Z80C3010PSG Z85C3016PSG
Z80C3008VSG Z80C3010VSG Z85C3016VSG
Z85C3008PSG/PEG Z85C3010PSG/PEG
Z85C3008VSG/VEG Z85C3010VSG/VEG
Z 80C30 16 P S G
Environmen ta l Fl ow
G = Lead Free
Temperature Range
S = 0º C to +70º C
E = Extended, –40° C to +100° C
Package
P = Plastic DIP
V = Plastic Leaded Chip Carrier
D = Ceramic DIP
Speed
8 = 8 MHz
10 = 10 MHz
16 = 16 MHz
Product Number
Zilog Prefix
PS011706-0511 Customer Support
CMOS SCC Serial Communications Controller
Product Specification
73
Customer Support
To share comments, get your technical questions answered, or report issues you may be
experiencing with our products, please visit Zilog’s Technical Support page at
http://support.zilog.com.
To learn more about this product, find additional documentation, or to discover other fac-
ets about Zilog product offerings, please visit the Zilog Knowledge Base at http://
zilog.com/kb or consider participating in the Zilog Forum at http://zilog.com/forum.
This publication is subject to replacement by a later edition. To determine whether a later
edition exists, please visit the Zilog website at http://www.zilog.com.