INCH-POUND MS3475G w/AMENDMENT 1 27 October 2015 SUPERSEDING MS3475G 11 March 2015 DETAIL SPECIFICATION SHEET CONNECTORS, PLUG, ELECTRICAL, RFI SHIELDED, SERIES 2, CRIMP TYPE, BAYONET COUPLING, CLASSES A, D, L, T, W AND K Reactivated after 1 March 2007, and may be used for new and existing designs and acquisitions. This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-26482. NOTE: For "XX", see note 5 and table I for contact cavities requiring reduced dimensions. FIGURE 1. Plug, dimensions. AMSC N/A FSC 5935 MS3475G w/AMENDMENT 1 FIGURE 1. Plug, dimensions - Continued. 2 MS3475G w/AMENDMENT 1 DETAIL T (COUPLING RING REMOVED FOR CLARITY) FIGURE 1. Plug, dimensions - Continued. 3 MS3475G w/AMENDMENT 1 FIGURE 1. Plug, dimensions - Continued. 4 MS3475G w/AMENDMENT 1 COUPLED POSITION ASSEMBLED TO RFI BACKSHELL FIGURE 1. Plug, dimensions - Continued. 5 MS3475G w/AMENDMENT 1 Max weight lbs (grams) 1/ Shell size A F R S V''' Pin Socket 8 .782 (19.86) .887 (22.53) .369 (9.37) 2.334 (59.28) .0204 (9.26) .0216 (9.81) 10 .926 (23.52) .887 (22.53) .497 (12.62) 2.334 (59.28) .0406 (18.43) .0421 (19.11) 12 1.043 (26.49) .887 (22.53) .614 (15.60) 2.334 (59.28) .0505 (22.93) .0536 (24.33) 14 1.183 (30.05) .887 (22.53) .739 (18.77) 2.334 (59.28) .0639 (29.01) .0692 (31.42) 16 1.305 (33.15) .887 (22.53) .864 (21.95) 2.334 (59.28) .0788 (35.77) .0880 (39.95) 18 1.391 (35.33) .887 (22.53) .969 (24.61) 2.334 (59.28) .0864 (39.22) .0957 (43.44) 20 1.531 (38.89) .825 (20.96) 1.094 (27.79) 2.334 (59.28) .1016 (46.12) .1114 (50.57) 22 1.656 (42.06) .825 (20.96) 1.219 (30.96) 2.334 (59.28) .1241 (56.34) .1363 (61.88) 24 1.777 (45.14) .825 (20.96) 1.344 (34.14) 2.334 (59.28) .1400 (63.56) .1916 (86.98) .363 (9.22) .343 (8.71) .425 (10.80) .405 (10.29) 1/ Less contacts and accessories. Maximum weights do not apply to class S. Inches .008 .025 .029 .032 .042 .045 .046 mm 0.20 0.64 0.74 0.81 1.07 1.14 1.17 Inches .065 .069 .087 .097 .101 .107 mm 1.66 1.75 2.21 2.46 2.57 2.72 Inches .187 .200 .218 .225 .269 .200 mm 4.75 5.08 5.54 5.72 6.83 5.08 Inches .320 .337 .357 .399 .419 1.230 mm 8.13 8.56 9.07 10.13 10.64 31.24 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only and are in parentheses. 2. Unless otherwise specified, tolerances are .005 (0.13 mm) for 3 place decimals, .01 (0.3 mm) for 2 place decimals, and 1 for all angles. 3. Color bands: .070 .031 (1.78 0.79 mm) wide, color blue. 4. Connector assembly must be used with a backshell. Backshells must be procured separately. See SAE-AS85049 for applicable backshells. 5. Insert arrangements requiring reduced diameters for raised seal barrier on outer row of contact cavities as indicated. FIGURE 1. Plug, dimensions - Continued. 6 MS3475G w/AMENDMENT 1 TABLE I. Contact cavities requiring reduced diameters (XX) for pins and sockets in outer row of contact cavities. 1/ Shell size Insert arrangement Contact cavities 8 -33 & -98 A, B, C 12 14 -10 -12 C, G A, B, C, D, E, F, G, H 14 -18 A, C, E, G, J, L 14 -19 B, D, F, H, K, M 16 -26 A, B, C, D, E, F, G, H, J, K, L, M, N, P, R 18 -32 A, B, C, D, E, F, G, H, J, K, L, M, N, P, R, S, T 22 -41 A, B, C, D, E, F, G, H, J, K, L, M, N, P, R, S, T, U, V, W, X, Y 1/ The reduced diameter "XX" refers to the diameters of the raised seal barriers (pin barrier rings) or lead-in chamfers (socket entry holes) to ensure proper sealing of pin and socket after mating. See MIL-DTL-26482, connector intermateability control dimensions figure (series 1 and series 2) for reduced diameter "XX" for contact size 20 only. REQUIREMENTS: Dimensions and configuration: See figure 1 and table I. Connector mating: This connector mates with MS3470, MS3471, MS3472, MS3473, MS3474, MS3477 and MS3479. Connectors will mate with MS3115 (dummy stowage receptacle) and the following series 1 receptacles provided both mating connectors contain a full compliment of power contacts: MS3110, MS3112, MS3113, MS3114, MS3119, MS3120, MS3122, MS3124, MS3127 and MS3128. Intermateability and rear accessory interchangeability dimensions are in accordance with MIL-DTL-26482. Class E is cancelled and replaced by class L. Class Z is cancelled and superseded by class K. This specification sheet supersedes MIL-C-83723/42 and MIL-C-83723/43. For insert arrangement, see MIL-STD-1669. Insert arrangements requiring reduced diameters for raised seal barriers or lead-in chamfers on outer row of contact cavities as indicated, see table I. Connector identification marking shall be in accordance with MIL-DTL-26482. Example: MS3475L----, minimum height does not apply to shell sizes 8, 10 and 12. Part or Identifying Number (PIN) example: MS3475 L 24 MS number Class Shell size Insert arrangement Contact style Alternate insert position 7 - 61 P W MS3475G w/AMENDMENT 1 Amendment notations. The margins of this specification are marked with vertical lines to indicate modifications generated by this amendment. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations. Referenced documents. In addition to MIL-DTL-26482, this document references the following: MS3110 MS3112 MS3113 MS3114 MS3115 MS3119 MS3120 MS3122 MS3124 MS3127 MS3128 MS3470 MS3471 MS3472 MS3473 MS3474 MS3477 MS3479 MIL-STD-1669 SAE-AS85049 CONCLUDING MATERIAL Custodians: Army - CR Navy - AS Air Force - 85 DLA - CC Preparing activity: DLA - CC (Project 5935-2015-225) Review activities: Army - AR, AV Navy - EC, SH Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https://assist.dla.mil. 8