SN54273, SN54LS273, SN74273, SN74LS273 OCTAL D-TYPE FLIP-FLOP WITH CLEAR SDLS090 - OCTOBER 1976 - REVISED MARCH 1988 * * * * Contains Eight Flip-Flops With Single-Rail Outputs Buffered Clock and Direct Clear Inputs Individual Data Input to Each Flip-Flop Applications Include: Buffer/Storage Registers Shift Registers Pattern Generators SN54273, SN74LS273 . . . J OR W PACKAGE SN74273 . . . N PACKAGE SN74LS273 . . . DW OR N PACKAGE (TOP VIEW) CLR 1Q 1D 2D 2Q 3Q 3D 4D 4Q GND description These monolithic, positive-edge-triggered flipflops utilize TTL circuitry to implement D-type flip-flop logic with a direct clear input. Information at the D inputs meeting the setup time requirements is transferred to the Q outputs on the positive-going edge of the clock pulse. Clock triggering occurs at a particular voltage level and is not directly related to the transition time of the positive-going pulse. When the clock input is at either the high or low level, the D input signal has no effect ar the output. 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC 8Q 8D 7D 7Q 6Q 6D 5D 5Q CLK 1D 1Q CLR V CC 8Q SN54LS273 . . . FK PACKAGE (TOP VIEW) 2D 2Q 3Q 3D 4D 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 8D 7D 7Q 6Q 6D 4Q GND CLK 5Q 5D These flip-flops are guaranteed to respond to clock frequencies ranging form 0 to 30 megahertz while maximum clock frequency is typically 40 megahertz. Typical power dissipation is 39 milliwatts per flip-flop for the 273 and 10 milliwatts for the LS273. logic symbol FUNCTION TABLE (each flip-flop) INPUTS 1 CLEAR CLOCK D OUTPUT Q L X X L H H H H L L H L X Q0 CLR CLK 1D 2D 3D 4D 5D 6D 7D 8D 1 11 3 4 EN C1 1D 2 5 7 6 8 9 13 12 14 15 17 16 18 19 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q This symbol is in accordance with ANSI/IEEE Std. 91-1984 and IEC Publication 617-12. Pin numbers shown are for the DW, J, N, and W packages. Copyright 1988, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SN54273, SN54LS273, SN74273, SN74LS273 OCTAL D-TYPE FLIP-FLOP WITH CLEAR SDLS090 - OCTOBER 1976 - REVISED MARCH 1988 schematics of inputs and outputs 273 EQUIVALENT OF EACH INPUT TYPICAL OF ALL OUTPUTS VCC VCC 100 NOM Req INPUT OUTPUT Clear: Req = 3 k NOM Clock: Req = 6 k NOM All other inputs: Req = 8 k NOM LS273 TYPICAL OF ALL OUTPUTS EQUIVALENT OF EACH INPUT VCC 120 NOM VCC 20 k NOM INPUT OUTPUT logic diagram (positive logic) CLOCK 11 1D 2D 3D 4D 3 4 7 8 1D 1D C1 R CLEAR 1D C1 1D C1 R C1 R R 1 2 1Q 5 2Q 6 3Q 9 4Q Pin numbers shown are for the DW, J, N, and W packages. 2 18 1D C1 R 8D 17 1D C1 R 7D 14 1D C1 R 6D 13 1D C1 R 5D POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 12 5Q 15 6Q 16 7Q 19 8Q SN54273, SN54LS273, SN74273, SN74LS273 OCTAL D-TYPE FLIP-FLOP WITH CLEAR SDLS090 - OCTOBER 1976 - REVISED MARCH 1988 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V Operating free-air temperature range, TA: SN54273 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55C to 125C SN74273 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0C to 70C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65C to 150C NOTE 1: Voltage values are with respect to network ground terminal. recommended operating conditions SN54273 Supply voltage, VCC MIN NOM 4.5 5 High-level output current, IOH SN74273 MAX MIN NOM 5.5 4.75 5 - 800 Low-level output current, IOL 16 Clock frequency, fclock 0 Width of clock or clear pulse, tw Setup time, time tsu 30 0 16.5 16.5 Data input 20 20 Clear inactive state 25 25 Data hold time, th 5 Operating free-air temperature, TA - 55 MAX 5.25 V - 800 A 16 mA 30 MHz ns ns 5 125 UNIT ns 0 70 C The arrow indicates that the rising edge of the clock pulse is used for reference. electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) TEST CONDITIONS PARAMETER VIH VIL High-level input voltage VIK Input clamp voltage VOH High-level output voltage VOL Low-level output voltage II Input current at maximum input voltage MIN TYP 2 High level input current High-level IIL Low level input current Low-level Clear Clock or D Clear Clock or D VCC = MIN, VCC = MIN, VIL = 0.8 V, II = - 12 mA VIH = 2 V, IOH = - 800 A VCC = MIN, VIL = 0.8 V, VIH = 2 V, IOH = 16 mA VCC = MAX, VI = 5.5 V VCC = MAX MAX, VI = 2 2.4 4V VCC = MAX MAX, VI = 0 0.4 4V 2.4 UNIT V Low-level input voltage IIH MAX 0.8 V -1.5 V 3.4 V 0.4 1 80 40 - 3.2 - 1.6 V mA A mA IOS Short-circuit output current VCC = MAX - 18 - 57 mA ICC Supply current VCC = MAX, See Note 2 62 94 mA For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. All typical values are at VCC = 5 V, TA = 25C. Not more than one output should be shorted at a time. NOTE 2: With all outputs open and 4.5 V applied to all data and clear inputs, ICC is measured after a momentary ground, then 4.5 V, is applied to clock. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 SN54273, SN54LS273, SN74273, SN74LS273 OCTAL D-TYPE FLIP-FLOP WITH CLEAR SDLS090 - OCTOBER 1976 - REVISED MARCH 1988 switching characteristics, VCC = 5 V, TA = 25C PARAMETER TEST CONDITIONS fmax tPHL Maximum clock frequency tPLH tPHL Propagation delay time, low-to-high-level output from clock MIN TYP 30 40 CL = 15 pF, RL = 400 , See Note 3 Propagation delay time, high-to-low-level output from clear Propagation delay time, high-to-low-level output from clock MAX UNIT MHz 18 27 ns 17 27 ns 18 27 ns NOTE 3: Load circuits and voltage waveforms are shown in Section 1. absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Operating free-air temperature range, TA: SN54LS273 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55C to 125C SN74LS273 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0C to 70C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65C to 150C NOTE 1: Voltage values are with respect to network ground terminal. recommended operating conditions SN54LS273 Supply voltage, VCC MIN NOM 4.5 5 High-level output current, IOH MIN NOM 5.5 4.75 5 4 Clock frequency, fclock 0 Width of clock or clear pulse, tw 30 0 20 20 Data input 20 20 Clear inactive state 25 25 Data hold time, th 5 Operating free-air temperature, TA - 55 The arrow indicates that the rising edge of the clock pulse is used for reference. 4 MAX - 400 Low-level output current, IOL Setup time, time tsu SN74LS273 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MAX 5.25 V - 400 A 8 mA 30 MHz ns ns 5 125 0 UNIT ns 70 C SN54273, SN54LS273, SN74273, SN74LS273 OCTAL D-TYPE FLIP-FLOP WITH CLEAR SDLS090 - OCTOBER 1976 - REVISED MARCH 1988 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) VIH VIL High-level input voltage VIK Input clamp voltage VOH High-level output voltage VOL II IIH IIL IOS SN54LS273 TYP MAX TEST CONDITIONS PARAMETER MIN 2 SN74LS273 TYP MAX MIN 2 Low-level input voltage UNIT V 0.7 0.8 V -1.5 -1.5 V VCC = MIN, VCC = MIN, VIL = VILmax, II = - 18 mA VIH = 2 V, IOH = - 400 A Low level output voltage Low-level VCC = MIN,, VIL = VILmax, VIH = 2 V,, Input current at maximum input voltage VCC = MAX, VI = 7 V 0.1 0.1 mA VI = 2.7 V VI = 0.4 V 20 20 A Low-level input current VCC = MAX, VCC = MAX, - 0.4 - 0.4 mA Short-circuit output current VCC = MAX - 100 mA High-level input current 2.5 IOL = 4 mA IOL = 8 mA 3.4 0.25 - 20 2.7 0.4 - 100 3.4 V 0.25 0.4 0.35 0.5 - 20 V ICC Supply current VCC = MAX, See Note 2 17 27 17 27 mA For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. All typical values are at VCC = 5 V, TA = 25C. Not more than one output should be shorted at a time and duration of short circuit should not exceed one second. NOTE 2: With all outputs open and 4.5 V applied to all data and clear inputs, ICC is measured after a momentary ground, then 4.5 V, is applied to clock. switching characteristics, VCC = 5 V, TA = 25C PARAMETER TEST CONDITIONS fmax tPHL Maximum clock frequency tPLH tPHL Propagation delay time, low-to-high-level output from clock Propagation delay time, high-to-low-level output from clear CL = 15 pF, RL = 2 k k, See Note 3 Propagation delay time, high-to-low-level output from clock MIN TYP 30 40 MAX UNIT MHz 18 27 ns 17 27 ns 18 27 ns NOTE 3: Load circuits and voltage waveforms are shown in Section 1. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 PACKAGE MATERIALS INFORMATION www.ti.com 5-Aug-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel Diameter Width (mm) W1 (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SN74LS273DWR SOIC DW 20 2000 330.0 24.4 10.8 13.0 2.7 12.0 24.0 Q1 SN74LS273NSR SO NS 20 2000 330.0 24.4 8.2 13.0 2.5 12.0 24.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 5-Aug-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74LS273DWR SOIC DW 20 2000 346.0 346.0 41.0 SN74LS273NSR SO NS 20 2000 346.0 346.0 41.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee(R) Solutions amplifier.ti.com dataconverter.ti.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2008, Texas Instruments Incorporated