-
+
LM4562
-
+
LM4562
-
+
LM4562
-
+
LM4562
10pF
+
+
INPUT
OUTPUT
47 k:
3320:
150:
909:
26.1 k:
3.83 k:
100:
150:
22 nF//4.7 nF//500 pF
3320:
47 nF//33 nF
LM4562
www.ti.com
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
LM4562 Dual High-Performance, High-Fidelity Audio Operational Amplifier
Check for Samples: LM4562
1FEATURES DESCRIPTION
The LM4562 is part of the ultra-low distortion, low-
2• Easily Drives 600ΩLoads noise, high-slew-rate operational amplifier series
• Optimized for Superior Audio Signal Fidelity optimized and fully specified for high-performance,
• Output Short Circuit Protection high-fidelity applications. The LM4562 audio
operational amplifiers deliver superior audio signal
• PSRR and CMRR Exceed 120dB (Typ) amplification for outstanding audio performance. The
• SOIC, PDIP, and TO-99 Packages LM4562 combines extremely low voltage noise
density (2.7nV/√Hz) with vanishingly low THD+N
APPLICATIONS (0.00003%) to easily satisfy the most demanding
audio applications. To ensure that the most
• Ultra High-Quality Audio Amplification challenging loads are driven without compromise, the
• High-Fidelity Preamplifiers LM4562 has a high slew rate of ±20V/μs and an
• High-Performance Professional Audio output current capability of ±26mA. Further, dynamic
range is maximized by an output stage that drives
• High-Fidelity Active Equalization and 2kΩloads to within 1V of either power supply voltage
Crossover Networks and to within 1.4V when driving 600Ωloads.
• High-Performance Line Drivers and Receivers The LM4562's outstanding CMRR (120dB), PSRR
(120dB), and VOS (0.1mV) give the amplifier excellent
KEY SPECIFICATIONS operational amplifier DC performance.
• Power Supply Voltage Range: ±2.5V to ± 17V The LM4562 has a wide supply range of ±2.5V to
• THD+N (AV= 1, VOUT = 3VRMS, fIN = 1kHz) ±17V. Over this supply range the LM4562’s input
– RL= 2kΩ: 0.00003% (typ) circuitry maintains excellent common-mode and
– RL= 600Ω: 0.00003% (typ) power supply rejection, as well as maintaining its low
input bias current. The LM4562 is unity gain stable.
• Input Noise Density: 2.7nV/√Hz (typ) This Audio Operational Amplifier achieves
• Slew Rate: ±20V/μs (typ) outstanding AC performance while driving complex
• Gain Bandwidth Product: 55MHz (typ) loads with values as high as 100pF.
• Open Loop Gain (RL= 600Ω): 140dB (typ) The LM4562 is available in an 8-lead narrow body
• Input Bias Current: 10nA (typ) SOIC, an 8-lead PDIP, and an 8-lead TO-99.
• Input Offset Voltage: 0.1mV (typ)
• DC Gain Linearity Error: 0.000009%
TYPICAL APPLICATION
A. 1% metal film resistors, 5% polypropylene capacitors
Passively Equalized RIAA Phono Preamplifier
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 2006–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
B
-+
A
- +
7
OUTPUT B
8V+
6
INVERTING INPUT B
5NON-INVERTING
INPUT B
NON-INVERTING
INPUT A
3
V-4
INVERTING INPUT A
2
OUTPUT A
1
Dual-In-Line Package
8
4
62
5
7
3
1
V+
OUTPUT BOUTPUT A
INVERTING
INPUT A
V-
INVERTING
INPUT B
NON-INVERTING
INPUT A
NON-INVERTING
INPUT B
LM4562
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
www.ti.com
CONNECTION DIAGRAMS
Figure 1. 8-Lead SOIC (D Package) Figure 2. 8-Lead TO-99 (LMC Package)
8-Lead PDIP (P Package)
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ABSOLUTE MAXIMUM RATINGS(1)(2)(3)
Power Supply Voltage (VS= V+- V-) 36V
Storage Temperature −65°C to 150°C
Input Voltage (V-) - 0.7V to (V+) + 0.7V
Output Short Circuit(4) Continuous
Power Dissipation Internally Limited
ESD Susceptibility(5) 2000V
ESD Susceptibility(6) Pins 1, 4, 7 and 8 200V
Pins 2, 3, 5 and 6 100V
Junction Temperature 150°C
Thermal Resistance θJA (D) 145°C/W
θJA (P) 102°C/W
θJA (LMC) 150°C/W
θJC (LMC) 35°C/W
Temperature Range (TMIN ≤TA≤TMAX) –40°C ≤TA≤85°C
Supply Voltage Range ±2.5V ≤VS≤± 17V
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.
(2) Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. For ensured
specifications and test conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed.
Some performance characteristics may degrade when the device is not operated under the listed test conditions.
(3) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(4) Amplifier output connected to GND, any number of amplifiers within a package.
(5) Human body model, 100pF discharged through a 1.5kΩresistor.
(6) Machine Model ESD test is covered by specification EIAJ IC-121-1981. A 200pF cap is charged to the specified voltage and then
discharged directly into the IC with no external series resistor (resistance of discharge path must be under 50Ω).
2Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
ELECTRICAL CHARACTERISTICS FOR THE LM4562(1)(2)
The specifications apply for VS= ±15V, RL= 2kΩ, fIN = 1kHz, TA= 25°C, unless otherwise specified.
LM4562 Units
Symbol Parameter Conditions (Limits)
Typical(3) Limit(4)
AV= 1, VOUT = 3Vrms
THD+N Total Harmonic Distortion + Noise RL= 2kΩ0.00003 % (max)
RL= 600Ω0.00003 0.00009
AV= 1, VOUT = 3VRMS
IMD Intermodulation Distortion 0.00005 %
Two-tone, 60Hz & 7kHz 4:1
GBWP Gain Bandwidth Product 55 45 MHz (min)
SR Slew Rate ±20 ±15 V/μs (min)
VOUT = 1VP-P, –3dB
FPBW Full Power Bandwidth referenced to output magnitude 10 MHz
at f = 1kHz
AV= –1, 10V step, CL= 100pF
tsSettling time 1.2 μs
0.1% error range
Equivalent Input Noise Voltage fBW = 20Hz to 20kHz 0.34 0.65 μVRMS
(max)
enf = 1kHz 2.7 4.7 nV/√Hz
Equivalent Input Noise Density f = 10Hz 6.4 (max)
inf = 1kHz 1.6
Current Noise Density pA/√Hz
f = 10Hz 3.1
VOS Offset Voltage ±0.1 ±0.7 mV (max)
Average Input Offset Voltage Drift vs
ΔVOS/ΔTemp –40°C ≤TA≤85°C 0.2 μV/°C
Temperature
Average Input Offset Voltage Shift vs
PSRR ΔVS= 20V(5) 120 110 dB (min)
Power Supply Voltage fIN = 1kHz 118
ISOCH-CH Channel-to-Channel Isolation dB
fIN = 20kHz 112
IBInput Bias Current VCM = 0V 10 72 nA (max)
Input Bias Current Drift vs
ΔIOS/ΔTemp –40°C ≤TA≤85°C 0.1 nA/°C
Temperature
IOS Input Offset Current VCM = 0V 11 65 nA (max)
Common-Mode Input Voltage Range +14.1 (V+) – 2.0
VIN-CM V (min)
–13.9 (V-) + 2.0
CMRR Common-Mode Rejection –10V<Vcm<10V 120 110 dB (min)
Differential Input Impedance 30 kΩ
ZIN Common Mode Input Impedance –10V<Vcm<10V 1000 MΩ
–10V<Vout<10V, RL= 600Ω140 125
AVOL Open Loop Voltage Gain –10V<Vout<10V, RL= 2kΩ140 dB (min)
–10V<Vout<10V, RL= 10kΩ140
RL= 600Ω±13.6 ±12.5
VOUTMAX Maximum Output Voltage Swing RL= 2kΩ±14.0 V (min)
RL= 10kΩ±14.1
IOUT Output Current RL= 600Ω, VS= ±17V ±26 ±23 mA (min)
+53
IOUT-CC Instantaneous Short Circuit Current mA
–42
fIN = 10kHz
ROUT Output Impedance Closed-Loop 0.01 Ω
Open-Loop 13
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.
(2) Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. For ensured
specifications and test conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed.
Some performance characteristics may degrade when the device is not operated under the listed test conditions.
(3) Typical specifications are specified at +25ºC and represent the most likely parametric norm.
(4) Tested limits are specified to AOQL (Average Outgoing Quality Level).
(5) PSRR is measured as follows: VOS is measured at two supply voltages, ±5V and ±15V. PSRR = | 20log(ΔVOS/ΔVS) |.
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM4562
LM4562
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
www.ti.com
ELECTRICAL CHARACTERISTICS FOR THE LM4562(1)(2) (continued)
The specifications apply for VS= ±15V, RL= 2kΩ, fIN = 1kHz, TA= 25°C, unless otherwise specified.
LM4562 Units
Symbol Parameter Conditions (Limits)
Typical(3) Limit(4)
CLOAD Capacitive Load Drive Overshoot 100pF 16 %
ISTotal Quiescent Current IOUT = 0mA 10 12 mA (max)
4Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
0.00001
0.0001
0.001
0.01
0.00002
0.0002
0.002
0.00005
0.0005
0.005
100m
10m 1 20
10
THD+N (%)
OUTPUT VOLTAGE (V)
0.00001
0.0001
0.001
0.01
0.00002
0.0002
0.002
0.00005
0.0005
0.005
100m
10m 120
10
THD+N (%)
OUTPUT VOLTAGE (V)
100m 2500m 1
0.00001
0.01
0.00002
0.00005
0.0001
0.0002
0.0005
0.001
0.002
0.005
105200m
OUTPUT VOLTAGE (V)
THD + N (%)
0.00001
0.0001
0.001
0.01
0.00002
0.0002
0.002
0.00005
0.0005
0.005
100m
10m 120
10
OUTPUT VOLTAGE (V)
THD+N (%)
0.00001
0.0001
0.001
0.01
0.00002
0.0002
0.002
0.00005
0.0005
0.005
100m
OUTPUT VOLTAGE (V)
10m 120
10
THD+N (%)
0.00001
0.0001
0.001
0.01
0.00002
0.0002
0.002
0.00005
0.0005
0.005
100m
10m 120
10
OUTPUT VOLTAGE (V)
THD+N (%)
LM4562
www.ti.com
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS
THD+N vs Output Voltage THD+N vs Output Voltage
VCC = 15V, VEE = –15V VCC = 12V, VEE = –12V
RL= 2kΩRL= 2kΩ
Figure 3. Figure 4.
THD+N vs Output Voltage THD+N vs Output Voltage
VCC = 17V, VEE = –17V VCC = 2.5V, VEE = –2.5V
RL= 2kΩRL= 2kΩ
Figure 5. Figure 6.
THD+N vs Output Voltage THD+N vs Output Voltage
VCC = 15V, VEE = –15V VCC = 12V, VEE = –12V
RL= 600ΩRL= 600Ω
Figure 7. Figure 8.
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM4562
0.00001
0.0001
0.001
0.01
0.00002
0.0002
0.002
0.00005
0.0005
0.005
100m
10m 120
10
THD+N (%)
OUTPUT VOLTAGE (V)
0.00001
0.0001
0.001
0.01
0.00002
0.0002
0.002
0.00005
0.0005
0.005
10m 120
100m 10
OUTPUT VOLTAGE (V)
THD+N (%)
0.00001
0.0001
0.001
0.01
0.00002
0.0002
0.002
0.00005
0.0005
0.005
100m
10m 1 20
10
THD+N (%)
OUTPUT VOLTAGE (V)
100m 2500m 1
0.00001
0.01
0.00002
0.00005
0.0001
0.0002
0.0005
0.001
0.002
0.005
10
5200m
OUTPUT VOLTAGE (V)
THD + N (%)
0.00001
0.0001
0.001
0.01
0.00002
0.0002
0.002
0.00005
0.0005
0.005
100m
10m 120
10
THD+N (%)
OUTPUT VOLTAGE (V)
LM4562
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
THD+N vs Output Voltage THD+N vs Output Voltage
VCC = 17V, VEE = –17V VCC = 2.5V, VEE = –2.5V
RL= 600ΩRL= 600Ω
Figure 9. Figure 10.
THD+N vs Output Voltage THD+N vs Output Voltage
VCC = 15V, VEE = –15V VCC = 12V, VEE = –12V
RL= 10kΩRL= 10kΩ
Figure 11. Figure 12.
THD+N vs Output Voltage THD+N vs Output Voltage
VCC = 17V, VEE = –17V VCC = 2.5V, VEE = –2.5V
RL= 10kΩRL= 10kΩ
Figure 13. Figure 14.
6Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
20 100 1k 10k 20k
0.00001
0.0001
0.001
0.01
%
Hz
0.00002
0.0002
0.002
0.00005
0.0005
0.005
50 200 2k500 5k
20 100 1k 10k 20k
0.00001
0.0001
0.001
0.01
%
Hz
0.00002
0.0002
0.002
0.00005
0.0005
0.005
50 200 2k500 5k
20 100 1k 10k 20k
0.00001
0.0001
0.001
0.01
%
Hz
0.00002
0.0002
0.002
0.00005
0.0005
0.005
50 200 2k500 5k
20 100 1k 10k 20k
0.00001
0.0001
0.001
0.01
%
Hz
0.00002
0.0002
0.002
0.00005
0.0005
0.005
50 200 2k500 5k
20 100 1k 10k 20k
0.00001
0.0001
0.001
0.01
%
Hz
0.00002
0.0002
0.002
0.00005
0.0005
0.005
50 200 2k500 5k
20 100 1k 10k 20k
0.00001
0.0001
0.001
0.01
%
Hz
0.00002
0.0002
0.002
0.00005
0.0005
0.005
50 200 2k500 5k
LM4562
www.ti.com
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
THD+N vs Frequency THD+N vs Frequency
VCC = 15V, VEE = –15V, VOUT = 3VRMS VCC = 12V, VEE = –12V, VOUT = 3VRMS
RL= 2kΩRL= 2kΩ
Figure 15. Figure 16.
THD+N vs Frequency THD+N vs Frequency
VCC = 17V, VEE = –17V, VOUT = 3VRMS VCC = 15V, VEE = –15V, VOUT = 3VRMS
RL= 2kΩRL= 600Ω
Figure 17. Figure 18.
THD+N vs Frequency THD+N vs Frequency
VCC = 12V, VEE = –12V, VOUT = 3VRMS VCC = 17V, VEE = –17V, VOUT = 3VRMS
RL= 600ΩRL= 600Ω
Figure 19. Figure 20.
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM4562
1
OUTPUT VOLTAGE (V)
102 5
0.00001
0.00002
0.00005
0.0001
0.0002
0.0005
0.001
0.002
0.005
0.01
IMD (%)
100m 200m 500m
0.00001
0.0001
0.001
0.01
IMD (%)
0.00002
0.0002
0.002
0.000007
0.00005
0.0005
0.005
OUTPUT VOLTAGE (V)
5100m 200m 500m 1 2 10
0.00001
0.0001
0.001
0.01
IMD (%)
0.00002
0.0002
0.002
0.000007
0.00005
0.0005
0.005
OUTPUT VOLTAGE (V)
5100m 200m 500m 1 2 10
20 100 1k 10k 20k
0.00001
0.0001
0.001
0.01
%
Hz
0.00002
0.0002
0.002
0.00005
0.0005
0.005
50 200 2k500 5k
20 100 1k 10k 20k
0.00001
0.0001
0.001
0.01
%
Hz
0.00002
0.0002
0.002
0.00005
0.0005
0.005
50 200 2k500 5k
20 100 1k 10k 20k
0.00001
0.0001
0.001
0.01
%
Hz
0.00002
0.0002
0.002
0.00005
0.0005
0.005
50 200 2k500 5k
LM4562
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
THD+N vs Frequency THD+N vs Frequency
VCC = 15V, VEE = –15V, VOUT = 3VRMS VCC = 12V, VEE = –12V, VOUT = 3VRMS
RL= 10kΩRL= 10kΩ
Figure 21. Figure 22.
THD+N vs Frequency IMD vs Output Voltage
VCC = 17V, VEE = –17V, VOUT = 3VRMS VCC = 15V, VEE = –15V
RL= 10kΩRL= 2kΩ
Figure 23. Figure 24.
IMD vs Output Voltage IMD vs Output Voltage
VCC = 12V, VEE = –12V VCC = 2.5V, VEE = –2.5V
RL= 2kΩRL= 2kΩ
Figure 25. Figure 26.
8Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
OUTPUT VOLTAGE (V)
100m
0.00001
0.00002
0.00005
0.0001
0.0002
0.0005
0.001
0.002
0.005
0.01
IMD (%)
300m 500m 700m 1
0.00001
0.0001
0.001
0.01
IMD (%)
0.00002
0.0002
0.002
0.000006
0.00005
0.0005
0.005
OUTPUT VOLTAGE (V)
5100m 200m 500m 1 2 10
0.00001
0.0001
0.001
0.01
IMD (%)
0.00002
0.0002
0.002
0.000006
0.00005
0.0005
0.005
OUTPUT VOLTAGE (V)
5100m 200m 500m 1 2 10
0.00001
0.0001
0.001
0.01
IMD (%)
0.00002
0.0002
0.002
0.000007
0.00005
0.0005
0.005
OUTPUT VOLTAGE (V)
5100m 200m 500m 1 2 10
0.00001
0.0001
0.001
0.01
IMD (%)
0.00002
0.0002
0.002
0.000007
0.00005
0.0005
0.005
OUTPUT VOLTAGE (V)
5100m 200m 500m 1 2 10
0.00001
0.0001
0.001
0.01
IMD (%)
0.00002
0.0002
0.002
0.000006
0.00005
0.0005
0.005
OUTPUT VOLTAGE (V)
5100m 200m 500m 1 2 10
LM4562
www.ti.com
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
IMD vs Output Voltage IMD vs Output Voltage
VCC = 17V, VEE = –17V VCC = 15V, VEE = –15V
RL= 2kΩRL= 600Ω
Figure 27. Figure 28.
IMD vs Output Voltage IMD vs Output Voltage
VCC = 12V, VEE = –12V VCC = 17V, VEE = –17V
RL= 600ΩRL= 600Ω
Figure 29. Figure 30.
IMD vs Output Voltage IMD vs Output Voltage
VCC = 2.5V, VEE = –2.5V VCC = 15V, VEE = –15V
RL= 600ΩRL= 10kΩ
Figure 31. Figure 32.
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM4562
20 20k
FREQUENCY (Hz)
+0
CROSSTALK (dB)
10k1k 2k 5k50 100 200 500
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
1100
FREQUENCY (Hz)
1
10
100
CURRENT NOISE (pA/ Hz)
10 1000 10000 100000
1
10
100
VS = 30V
VCM = 15V
1.6 pA/ Hz
0.00001
0.01
0.00002
0.00005
0.0001
0.0002
0.0005
0.001
0.002
0.005
100m 1300m 500m 700m
OUTPUT VOLTAGE (V)
IMD (%)
1100
FREQUENCY (Hz)
1
10
100
10 1000 10000 100000
1
10
100
VS = 30V
VCM = 15V
2.7 nV/ Hz
VOLTAGE NOISE (nV/ Hz)
0.00001
0.0001
0.001
0.01
IMD (%)
0.00002
0.0002
0.002
0.000006
0.00005
0.0005
0.005
OUTPUT VOLTAGE (V)
5100m 200m 500m 1 2 10
0.00001
0.0001
0.001
0.01
IMD (%)
0.00002
0.0002
0.002
0.000006
0.00005
0.0005
0.005
OUTPUT VOLTAGE (V)
5100m 200m 500m 1 2 10
LM4562
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
IMD vs Output Voltage IMD vs Output Voltage
VCC = 12V, VEE = –12V VCC = 17V, VEE = –17V
RL= 10kΩRL= 10kΩ
Figure 33. Figure 34.
IMD vs Output Voltage
VCC = 2.5V, VEE = –2.5V
RL= 10kΩVoltage Noise Density vs Frequency
Figure 35. Figure 36.
Crosstalk vs Frequency
VCC = 15V, VEE = –15V, VOUT = 3VRMS
Current Noise Density vs Frequency AV= 0dB, RL= 2kΩ
Figure 37. Figure 38.
10 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
-130
+0
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
20 20k10k5k2k1k50020010050
FREQUENCY (Hz)
CROSSTALK (dB)
20 20k
FREQUENCY (Hz)
+0
CROSSTALK (dB)
10k1k 2k 5k50 100 200 500
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
20 20k
FREQUENCY (Hz)
+0
CROSSTALK (dB)
10k1k 2k 5k50 100 200 500
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
20 20k
FREQUENCY (Hz)
+0
CROSSTALK (dB)
10k1k 2k 5k50 100 200 500
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
20 20k
FREQUENCY (Hz)
+0
CROSSTALK (dB)
10k1k 2k 5k50 100 200 500
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
20 20k
FREQUENCY (Hz)
+0
CROSSTALK (dB)
10k1k 2k 5k50 100 200 500
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
LM4562
www.ti.com
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Crosstalk vs Frequency Crosstalk vs Frequency
VCC = 15V, VEE = –15V, VOUT = 10VRMS VCC = 12V, VEE = –12V, VOUT = 3VRMS
AV= 0dB, RL= 2kΩAV= 0dB, RL= 2kΩ
Figure 39. Figure 40.
Crosstalk vs Frequency Crosstalk vs Frequency
VCC = 12V, VEE = –12V, VOUT = 10VRMS VCC = 17V, VEE = –17V, VOUT = 3VRMS
AV= 0dB, RL= 2kΩAV= 0dB, RL= 2kΩ
Figure 41. Figure 42.
Crosstalk vs Frequency Crosstalk vs Frequency
VCC = 17V, VEE = –17V, VOUT = 10VRMS VCC = 2.5V, VEE = –2.5V, VOUT = 1VRMS
AV= 0dB, RL= 2kΩAV= 0dB, RL= 2kΩ
Figure 43. Figure 44.
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM4562
20 20k
FREQUENCY (Hz)
+0
CROSSTALK (dB)
10k1k 2k 5k50 100 200 500
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
20 20k
FREQUENCY (Hz)
+0
CROSSTALK (dB)
10k1k 2k 5k50 100 200 500
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
20 20k
FREQUENCY (Hz)
+0
CROSSTALK (dB)
10k1k 2k 5k50 100 200 500
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
20 20k
FREQUENCY (Hz)
+0
CROSSTALK (dB)
10k1k 2k 5k50 100 200 500
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
20 20k
FREQUENCY (Hz)
+0
CROSSTALK (dB)
10k1k 2k 5k50 100 200 500
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
20 20k
FREQUENCY (Hz)
+0
CROSSTALK (dB)
10k1k 2k 5k50 100 200 500
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
LM4562
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Crosstalk vs Frequency Crosstalk vs Frequency
VCC = 15V, VEE = –15V, VOUT = 3VRMS VCC = 15V, VEE = –15V, VOUT = 10VRMS
AV= 0dB, RL= 600ΩAV= 0dB, RL= 600Ω
Figure 45. Figure 46.
Crosstalk vs Frequency Crosstalk vs Frequency
VCC = 12V, VEE = –12V, VOUT = 3VRMS VCC = 12V, VEE = –12V, VOUT = 10VRMS
AV= 0dB, RL= 600ΩAV= 0dB, RL= 600Ω
Figure 47. Figure 48.
Crosstalk vs Frequency Crosstalk vs Frequency
VCC = 17V, VEE = –17V, VOUT = 3VRMS VCC = 17V, VEE = –17V, VOUT = 10VRMS
AV= 0dB, RL= 600ΩAV= 0dB, RL= 600Ω
Figure 49. Figure 50.
12 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
-140
+0
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
20 20k50 100 200 500 1k 2k 5k 10k
FREQUENCY (Hz)
CROSSTALK (dB)
-140
+0
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
20 20k50 100 200 500 1k 2k 5k 10k
FREQUENCY (Hz)
CROSSTALK (dB)
-140
+0
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
20 20k50 100 200 500 1k 2k 5k 10k
FREQUENCY (Hz)
CROSSTALK (dB)
-140
+0
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
20 20k50 100 200 500 1k 2k 5k 10k
FREQUENCY (Hz)
CROSSTALK (dB)
-140
+0
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
20 20k50 100 200 500 1k 2k 5k 10k
FREQUENCY (Hz)
CROSSTALK (dB)
20 20k
FREQUENCY (Hz)
+0
CROSSTALK (dB)
10k1k 2k 5k50 100 200 500
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
LM4562
www.ti.com
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Crosstalk vs Frequency Crosstalk vs Frequency
VCC = 2.5V, VEE = –2.5V, VOUT = 1VRMS VCC = 15V, VEE = –15V, VOUT = 3VRMS
AV= 0dB, RL= 600ΩAV= 0dB, RL= 10kΩ
Figure 51. Figure 52.
Crosstalk vs Frequency Crosstalk vs Frequency
VCC = 15V, VEE = –15V, VOUT = 10VRMS VCC = 12V, VEE = –12V, VOUT = 3VRMS
AV= 0dB, RL= 10kΩAV= 0dB, RL= 10kΩ
Figure 53. Figure 54.
Crosstalk vs Frequency Crosstalk vs Frequency
VCC = 12V, VEE = –12V, VOUT = 10VRMS VCC = 17V, VEE = –17V, VOUT = 3VRMS
AV= 0dB, RL= 10kΩAV= 0dB, RL= 10kΩ
Figure 55. Figure 56.
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM4562
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
-140
+0
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
20 20k50 100 200 500 1k 2k 5k 10k
FREQUENCY (Hz)
CROSSTALK (dB)
-140
+0
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
20 20k50 100 200 500 1k 2k 5k 10k
FREQUENCY (Hz)
CROSSTALK (dB)
LM4562
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Crosstalk vs Frequency Crosstalk vs Frequency
VCC = 17V, VEE = –17V, VOUT = 10VRMS VCC = 2.5V, VEE = –2.5V, VOUT = 1VRMS
AV= 0dB, RL= 10kΩAV= 0dB, RL= 10kΩ
Figure 57. Figure 58.
PSRR+ vs Frequency PSRR- vs Frequency
VCC = 15V, VEE = –15V VCC = 15V, VEE = –15V
RL= 10kΩ, f = 200kHz, VRIPPLE = 200mVpp RL= 10kΩ, f = 200kHz, VRIPPLE = 200mVpp
Figure 59. Figure 60.
PSRR+ vs Frequency PSRR- vs Frequency
VCC = 15V, VEE = –15V VCC = 15V, VEE = –15V
RL= 2kΩ, f = 200kHz, VRIPPLE = 200mVpp RL= 2kΩ, f = 200kHz, VRIPPLE = 200mVpp
Figure 61. Figure 62.
14 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
LM4562
www.ti.com
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
PSRR+ vs Frequency PSRR- vs Frequency
VCC = 15V, VEE = –15V VCC = 15V, VEE = –15V
RL= 600Ω, f = 200kHz, VRIPPLE = 200mVpp RL= 600Ω, f = 200kHz, VRIPPLE = 200mVpp
Figure 63. Figure 64.
PSRR+ vs Frequency PSRR– vs Frequency
VCC = 12V, VEE = –12V VCC = 12V, VEE = –12V
RL= 10kΩ, f = 200kHz, VRIPPLE = 200mVpp RL= 10kΩ, f = 200kHz, VRIPPLE = 200mVpp
Figure 65. Figure 66.
PSRR+ vs Frequency PSRR– vs Frequency
VCC = 12V, VEE = –12V VCC = 12V, VEE = –12V
RL= 2kΩ, f = 200kHz, VRIPPLE = 200mVpp RL= 2kΩ, f = 200kHz, VRIPPLE = 200mVpp
Figure 67. Figure 68.
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM4562
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
LM4562
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
PSRR+ vs Frequency PSRR– vs Frequency
VCC = 12V, VEE = –12V VCC = 12V, VEE = –12V
RL= 600Ω, f = 200kHz, VRIPPLE = 200mVpp RL= 600Ω, f = 200kHz, VRIPPLE = 200mVpp
Figure 69. Figure 70.
PSRR+ vs Frequency PSRR– vs Frequency
VCC = 17V, VEE = –17V VCC = 17V, VEE = –17V
RL= 10kΩ, f = 200kHz, VRIPPLE = 200mVpp RL= 10kΩ, f = 200kHz, VRIPPLE = 200mVpp
Figure 71. Figure 72.
PSRR+ vs Frequency PSRR– vs Frequency
VCC = 17V, VEE = –17V VCC = 17V, VEE = –17V
RL= 2kΩ, f = 200kHz, VRIPPLE = 200mVpp RL= 2kΩ, f = 200kHz, VRIPPLE = 200mVpp
Figure 73. Figure 74.
16 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
LM4562
www.ti.com
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
PSRR+ vs Frequency PSRR– vs Frequency
VCC = 17V, VEE = –17V VCC = 17V, VEE = –17V
RL= 600Ω, f = 200kHz, VRIPPLE = 200mVpp RL= 600Ω, f = 200kHz, VRIPPLE = 200mVpp
Figure 75. Figure 76.
PSRR+ vs Frequency PSRR– vs Frequency
VCC = 2.5V, VEE = –2.5V VCC = 2.5V, VEE = –2.5V
RL= 10kΩ, f = 200kHz, VRIPPLE = 200mVpp RL= 10kΩ, f = 200kHz, VRIPPLE = 200mVpp
Figure 77. Figure 78.
PSRR+ vs Frequency PSRR– vs Frequency
VCC = 2.5V, VEE = –2.5V VCC = 2.5V, VEE = –2.5V
RL= 2kΩ, f = 200kHz, VRIPPLE = 200mVpp RL= 2kΩ, f = 200kHz, VRIPPLE = 200mVpp
Figure 79. Figure 80.
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM4562
-120
-60
-40
-20
0
-100
-80
10 200k
100 1k 10k 100k
FREQUENCY (Hz)
CMRR (dB)
-120
-60
-40
-20
0
-100
-80
10 200k100 1k 10k 100k
FREQUENCY (Hz)
CMRR (dB)
-120
-60
-40
-20
0
-100
-80
10 200k
100 1k 10k 100k
FREQUENCY (Hz)
CMRR (dB)
-120
-60
-40
-20
0
-100
-80
10 200k100 1k 10k 100k
FREQUENCY (Hz)
CMRR (dB)
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
FREQUENCY (Hz)
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
20 100 1k 10k 100k
PSRR (dB)
200k
LM4562
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
PSRR+ vs Frequency PSRR– vs Frequency
VCC = 2.5V, VEE = –2.5V VCC = 2.5V, VEE = –2.5V
RL= 600Ω, f = 200kHz, VRIPPLE = 200mVpp RL= 600Ω, f = 200kHz, VRIPPLE = 200mVpp
Figure 81. Figure 82.
CMRR vs Frequency CMRR vs Frequency
VCC = 15V, VEE = –15V VCC = 12V, VEE = –12V
RL= 2kΩRL= 2kΩ
Figure 83. Figure 84.
CMRR vs Frequency CMRR vs Frequency
VCC = 17V, VEE = –17V VCC = 2.5V, VEE = –2.5V
RL= 2kΩRL= 2kΩ
Figure 85. Figure 86.
18 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
-120
-60
-40
-20
0
-100
-80
10 200k100 1k 10k 100k
FREQUENCY (Hz)
CMRR (dB)
FREQUENCY (Hz)
CMRR (dB)
-120
0
-20
-40
-60
-80
-100
10 100 1k 10k 100k 200k
-120
-60
-40
-20
0
-100
-80
10 200k
100 1k 10k 100k
FREQUENCY (Hz)
CMRR (dB)
-120
-60
-40
-20
0
-100
-80
10 200k
100 1k 10k 100k
FREQUENCY (Hz)
CMRR (dB)
-120
-60
-40
-20
0
-100
-80
10 200k100 1k 10k 100k
FREQUENCY (Hz)
CMRR (dB)
FREQUENCY (Hz)
CMRR (dB)
-120
0
-20
-40
-60
-80
-100
10 100 1k 10k 100k 200k
LM4562
www.ti.com
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
CMRR vs Frequency CMRR vs Frequency
VCC = 15V, VEE = –15V VCC = 12V, VEE = –12V
RL= 600ΩRL= 600Ω
Figure 87. Figure 88.
CMRR vs Frequency CMRR vs Frequency
VCC = 17V, VEE = –17V VCC = 2.5V, VEE = –2.5V
RL= 600ΩRL= 600Ω
Figure 89. Figure 90.
CMRR vs Frequency CMRR vs Frequency
VCC = 15V, VEE = –15V VCC = 12V, VEE = –12V
RL= 10kΩRL= 10kΩ
Figure 91. Figure 92.
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LM4562
500 10k600 800 2k 5k
LOAD RESISTANCE (:)
OUTPUT (Vrms)
11.0
12.0
11.5
12.5
13.0
13.5
10.0
10.5
500 10k600 800 2k 5k
LOAD RESISTANCE (:)
OUTPUT (Vrms)
0.00
0.25
0.50
0.75
1.00
1.25
500 10k600 800 2k 5k
LOAD RESISTANCE (:)
OUTPUT (Vrms)
9.0
10.0
9.5
10.5
11.0
11.5
500 10k600 800 2k 5k
LOAD RESISTANCE (:)
OUTPUT (Vrms)
7.0
8.0
7.5
8.5
9.0
9.5
-120
-60
-40
-20
0
-100
-80
10 200k
100 1k 10k 100k
FREQUENCY (Hz)
CMRR (dB)
-120
-60
-40
-20
0
-100
-80
10 200k100 1k 10k 100k
FREQUENCY (Hz)
CMRR (dB)
LM4562
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
CMRR vs Frequency CMRR vs Frequency
VCC = 17V, VEE = –17V VCC = 2.5V, VEE = –2.5V
RL= 10kΩRL= 10kΩ
Figure 93. Figure 94.
Output Voltage vs Load Resistance Output Voltage vs Load Resistance
VDD = 15V, VEE = –15V VDD = 12V, VEE = –12V
THD+N = 1% THD+N = 1%
Figure 95. Figure 96.
Output Voltage vs Load Resistance Output Voltage vs Load Resistance
VDD = 17V, VEE = –17V VDD = 2.5V, VEE = –2.5V
THD+N = 1% THD+N = 1%
Figure 97. Figure 98.
20 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
8.0
8.5
9.0
9.5
10.0
10.5
2.5 4.5 6.5 8.5 10.5 12.5 14.5 16.5 18.5
SUPPLY VOLTAGE (V)
SUPPLY CURRENT (mA)
8.0
8.5
9.0
9.5
10.0
10.5
2.5 4.5 6.5 8.5 10.5 12.5 14.5 16.5 18.5
SUPPLY VOLTAGE (V)
SUPPLY CURRENT (mA)
4
6
8
10
12
14
2.5 4.5 6.5 8.5 10.5 12.5 14.5 16.5 18.5
SUPPLY VOLTAGE (V)
OUTPUT VOLTAGE (V)
2
0
8.0
8.5
9.0
9.5
10.0
10.5
2.5 4.5 6.5 8.5 10.5 12.5 14.5 16.5 18.5
SUPPLY VOLTAGE (V)
SUPPLY CURRENT (mA)
4
6
8
10
12
14
2.5 4.5 6.5 8.5 10.5 12.5 14.5 16.5 18.5
SUPPLY VOLTAGE (V)
OUTPUT VOLTAGE (V)
2
0
2
4
6
8
10
12
2.5 4.5 6.5 8.5 10.5 12.5 14.5 16.5 18.5
SUPPLY VOLTAGE (V)
OUTPUT VOLTAGE (V)
0
LM4562
www.ti.com
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Output Voltage vs Supply Voltage Output Voltage vs Supply Voltage
RL= 2kΩ, THD+N = 1% RL= 600Ω, THD+N = 1%
Figure 99. Figure 100.
Output Voltage vs Supply Voltage Supply Current vs Supply Voltage
RL= 10kΩ, THD+N = 1% RL= 2kΩ
Figure 101. Figure 102.
Supply Current vs Supply Voltage Supply Current vs Supply Voltage
RL= 600ΩRL= 10kΩ
Figure 103. Figure 104.
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: LM4562
1
': 0.00s
@: -1.01 Ps': 0.00V
@: -80.0 mV
M 200 ns A Ch1 2.00 mV
50.40%
Ch1 50.0 mV
1
': 0.00s
@: -1.01 Ps': 0.00V
@: -80.0 mV
M 200 ns A Ch1 2.00 mV
50.40%
Ch1 50.0 mV
100 10000 10000000
100000000
100000
1000
10
FREQUENCY (Hz)
1000000
180
-20
20
80
GAIN (dB), PHASE LAG (o)
140
120
60
40
0
100
160
100 10k 10M 100M100k
1k
10
FREQUENCY (Hz)
1M
2
-18
-14
-8
MAGNITUDE (dB)
-2
-4
-10
-12
-16
-6
0
1
0 dB = 1 VP-P
LM4562
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Full Power Bandwidth vs Frequency Gain Phase vs Frequency
Figure 105. Figure 106.
Small-Signal Transient Response Small-Signal Transient Response
AV= 1, CL= 10pF AV= 1, CL= 100pF
Figure 107. Figure 108.
22 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
Distortion Signal Gain = 1+(R2/R1)
+
-
LM4562
1000:
R1
10:
R2
Analyzer Input
Audio Precision
System Two
Cascade
Generator Output
Actual Distortion = AP Value/100
LM4562
www.ti.com
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
APPLICATION INFORMATION
DISTORTION MEASUREMENTS
The vanishingly low residual distortion produced by LM4562 is below the capabilities of all commercially available
equipment. This makes distortion measurements just slightly more difficult than simply connecting a distortion
meter to the amplifier’s inputs and outputs. The solution, however, is quite simple: an additional resistor. Adding
this resistor extends the resolution of the distortion measurement equipment.
The LM4562’s low residual distortion is an input referred internal error. As shown in Figure 109, adding the 10Ω
resistor connected between the amplifier’s inverting and non-inverting inputs changes the amplifier’s noise gain.
The result is that the error signal (distortion) is amplified by a factor of 101. Although the amplifier’s closed-loop
gain is unaltered, the feedback available to correct distortion errors is reduced by 101, which means that
measurement resolution increases by 101. To ensure minimum effects on distortion measurements, keep the
value of R1 low as shown in Figure 109.
This technique is verified by duplicating the measurements with high closed loop gain and/or making the
measurements at high frequencies. Doing so produces distortion components that are within the measurement
equipment’s capabilities. This datasheet’s THD+N and IMD values were generated using the above described
circuit connected to an Audio Precision System Two Cascade.
Figure 109. THD+N and IMD Distortion Test Circuit
The LM4562 is a high-speed op amp with excellent phase margin and stability. Capacitive loads up to 100pF will
cause little change in the phase characteristics of the amplifiers and are therefore allowable.
Capacitive loads greater than 100pF must be isolated from the output. The most straightforward way to do this is
to put a resistor in series with the output. This resistor will also prevent excess power dissipation if the output is
accidentally shorted.
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 23
Product Folder Links: LM4562
LM4562
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
www.ti.com
A. Complete shielding is required to prevent induced pick up from external sources. Always check with oscilloscope for
power line noise.
Figure 110. Noise Measurement Circuit
Total Gain: 115 dB @f = 1 kHz
Input Referred Noise Voltage: en= V0/560,000 (V)
Figure 111. RIAA Preamp Voltage Gain, RIAA Figure 112. Flat Amp Voltage Gain vs Frequency
Deviation vs Frequency
24 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
10 Fm0.1 Fm
C1C3
C4C2
10 kW
R7
R8
R2
R3
10 kW
10 kW
–VEE
+VCC JP3, pin 1
JP4, pin 1
JP1, pin 1
1 2 3 4
8 7 6 5
10 Fm
0.1 Fm
10 kW
–VEE
JP2, pin 1
+
–
+
–
+
–
+
–
LM4562
www.ti.com
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
Evaluation Module Schematic
Figure 113. Inverting Amplifiers
Typical Applications
AV= 34.5
F = 1 kHz
En= 0.38 μV
A Weighted
Figure 114. NAB Preamp
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 25
Product Folder Links: LM4562
LM4562
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
www.ti.com
Figure 115. NAB Preamp Voltage Gain vs Frequency
VO= V1–V2
Figure 116. Balanced to Single-Ended Converter
VO= V1 + V2 −V3 −V4
Figure 117. Adder/Subtracter
Figure 118. Sine Wave Oscillator
26 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
Illustration is f0= 1 kHz
Figure 119. Second-Order High-Pass Filter (Butterworth)
Illustration is f0= 1 kHz
Figure 120. Second-Order Low-Pass Filter (Butterworth)
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 27
Product Folder Links: LM4562
LM4562
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
www.ti.com
Illustration is f0= 1 kHz, Q = 10, ABP = 1
Figure 121. State Variable Filter
Figure 122. AC/DC Converter
Figure 123. 2-Channel Panning Circuit (Pan Pot)
28 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
,
fLB|
R
2S
1
C25 ,
1
R
2SC11
fHB| 1
2S
(+
R1 R5+2R3)C2
1
R
2S
C12
fL|
fH|
LM4562
www.ti.com
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
Figure 124. Line Driver
The equations started above are simplifications, providing guidance of general –3dB point values, when the
potentiometers are at their null position.
Illustration is:
fL≈32 Hz, fLB ≈320 Hz
fH≈11 kHz, fHB ≈1.1 kHz
Figure 125. Tone Control
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 29
Product Folder Links: LM4562
LM4562
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
www.ti.com
Av= 35 dB
En= 0.33 μV S/N = 90 dB
f = 1 kHz
A Weighted
A Weighted, VIN = 10 mV
@f = 1 kHz
Figure 126. RIAA Preamp
Illustration is:
V0 = 101(V2 −V1)
Figure 127. Balanced Input Mic Amp
30 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
A. See Table 1.
Figure 128. 10-Band Graphic Equalizer
Table 1. C1, C2, R1, and R2Values for Figure 128(1)
fo (Hz) C1C2R1R2
32 0.12μF 4.7μF 75kΩ500Ω
64 0.056μF 3.3μF 68kΩ510Ω
125 0.033μF 1.5μF 62kΩ510Ω
250 0.015μF 0.82μF 68kΩ470Ω
500 8200pF 0.39μF 62kΩ470Ω
1k 3900pF 0.22μF 68kΩ470Ω
2k 2000pF 0.1μF 68kΩ470Ω
4k 1100pF 0.056μF 62kΩ470Ω
8k 510pF 0.022μF 68kΩ510Ω
16k 330pF 0.012μF 51kΩ510Ω
(1) At volume of change = ±12 dB Q = 1.7
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 31
Product Folder Links: LM4562
LM4562
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
www.ti.com
REVISION HISTORY
Changes from Revision J (April 2013) to Revision K Page
• Added EVM schematic ....................................................................................................................................................... 25
32 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4562
LM4562
www.ti.com
SNAS326K –AUGUST 2006–REVISED DECEMBER 2013
REVISION HISTORY
Rev Date Description
1.0 08/16/06 Initial release.
1.1 08/22/06 Updated the Instantaneous Short Circuit Current specification.
1.2 09/12/06 Updated the three ±15V CMRR Typical Performance Curves.
1.3 09/26/06 Updated interstage filter capacitor values on page 1 Typical Application
schematic.
1.4 05/03/07 Added the “general note” under the EC table.
1.5 10/17/07 Replaced all the PSRR curves.
1.6 01/26/10 Edited the equations on page 28 (under Tone Control).
J 04/04/13 Changed layout of National Data Sheet to TI format
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 33
Product Folder Links: LM4562
PACKAGE OPTION ADDENDUM
www.ti.com 7-Nov-2017
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM4562MA/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 L4562
MA
LM4562MAX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 L4562
MA
LM4562NA/NOPB ACTIVE PDIP P 8 40 Green (RoHS
& no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 85 LM
4562NA
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
PACKAGE OPTION ADDENDUM
www.ti.com 7-Nov-2017
Addendum-Page 2
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM4562MAX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 11-Nov-2013
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM4562MAX/NOPB SOIC D 8 2500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 11-Nov-2013
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
LM4562HA/NOPB LM4562MA/NOPB LM4562MABD LM4562MAX/NOPB LM4562NA/NOPB