LT1083/LT1084/LT1085 Fixed 3A, 5A, 7.5A Low Dropout Positive Fixed Regulators U FEATURES DESCRIPTIO Three-Terminal 3.3V, 3.6V, 5V and 12V Output Current of 3A, 5A or 7.5A Operates Down to 1V Dropout Guaranteed Dropout Voltage at Multiple Current Levels Line Regulation: 0.015% Load Regulation: 0.1% 100% Thermal Limit Functional Test Adjustable Versions Available U APPLICATIO S High Efficiency Linear Regulators Post Regulators for Switching Supplies Constant Current Regulators Battery Chargers The LT(R)1083 series of positive adjustable regulators are designed to provide 3A, 5A and 7.5A with higher efficiency than currently available devices. All internal circuitry is designed to operate down to 1V input to output differential and the dropout voltage is fully specified as a function of load current. Dropout is guaranteed at a maximum of 1.5V at maximum output current, decreasing at lower load currents. On-chip trimming adjusts the output voltage to 1%. Current limit is also trimmed, minimizing the stress on both the regulator and power source circuitry under overload conditions. The LT1083 series devices are pin compatible with older three-terminal regulators. A 10F output capacitor is required on these new devices; however, this is usually included in most regulator designs. DEVICE OUTPUT CURRENT* LT1083 LT1084 LT1085 7.5 Amps 5.0 Amps 3.0 Amps *For a 1.5A low dropout regulator see the LT1086 data sheet. Unlike PNP regulators, where up to 10% of the output current is wasted as quiescent current, the LT1083 quiescent current flows into the load, increasing efficiency. , LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. U TYPICAL APPLICATIO 5V, 7.5A Regulator 5V AT 7.5A LT1083-5 + + 10F 22F* TANTALUM LT1083/4/5 TA01 *REQUIRED FOR STABILITY INPUT/OUTPUT VOLTAGE DIFFERENTIAL (V) VIN 6.5V Dropout Voltage vs Output Current 2 1 0 0 IFULLLOAD/2 OUTPUT CURRENT (A) IFULLLOAD 1083/4/5 TA02 1083ffd 1 LT1083/LT1084/LT1085 Fixed (Note 1) W Power Dissipation .............................. Internally Limited Input Voltage* ........................................................ 30V Operating Input Voltage 3.3V, 3.6V Devices ........................................... 20V 5V Devices ....................................................... 20V 12V Devices ..................................................... 25V Operating Junction Temperature Range "C" Grades Control Section .............................. 0C to 125C Power Transistor ............................ 0C to 150C "M" Grades Control Section .......................... -55C to 150C Power Transistor ........................ -55C to 200C Storage Temperature Range ................ - 65C to 150C Lead Temperature (Soldering, 10 sec)................. 300C *Although the devices maximum operating voltage is limited, (20V for a 3V, 5V device, and 25V for a 12V device) the devices are guaranteed to withstand transient input voltages up to 30V. For input voltages greater than the maximum operating input voltage some degradation of specifications will occur. For input/output voltage differentials greater than 15V, a minimum external load of 5mA is required to maintain regulation. U RATI GS UU W W AXI U U ABSOLUTE PRECO DITIO I G 100% Thermal Limit Functional Test. U U W PACKAGE/ORDER I FOR ATIO CASE IS OUTPUT VIN ORDER PART NUMBER LT1083CK-5 LT1083CK-12 LT1083MK-5 LT1083MK-12 LT1084CK-5 LT1084CK-12 2 1 GND K PACKAGE 2-LEAD TO-3 METAL CAN LT1084MK-5 LT1084MK-12 LT1085CK-5 LT1085CK-12 LT1085MK-5 LT1085MK-12 ORDER PART NUMBER TAB IS OUTPUT JA = 35C/W 3 VIN 2 VOUT 1 GND LT1083CP-5 LT1083CP-12 LT1084CP-5 LT1084CP-12 P PACKAGE 3-LEAD TO-3P PLASTIC OBSOLETE NOT RECOMMENDED FOR NEW DESIGNS TAB IS OUTPUT FRONT VIEW FRONT VIEW 3 VIN 2 VOUT 1 GND LT1084CT-3.3 LT1084CT-5 LT1084CT-12 LT1085CT-3.3 LT1085CT-3.6 LT1085CT-5 LT1085CT-12 T PACKAGE 3-LEAD PLASTIC TO-220 JA = 50C/W JA = 45C/W FRONT VIEW TAB IS OUTPUT 3 VIN 2 VOUT 1 GND LT1085CM-3.3 LT1085CM-3.6 LT1085IM-3.6 M PACKAGE 3-LEAD PLASTIC DD JA = 30C/W* *WITH PACKAGE SOLDERED TO 0.52IN2 COPPER AREA OVER BACKSIDE GROUND PLANE OR INTERNAL POWER PLANE. JA CAN VARY FROM 20C/W TO > 40C/W DEPENDING ON MOUNTING TECHNIQUE. Consult factory for parts specified with wider operating temperature ranges. 1083ffd 2 LT1083/LT1084/LT1085 Fixed ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. PARAMETER CONDITIONS Output Voltage LT1084-3.3 LT1085-3.3 LT1085-3.6 3.300 3.300 3.330 3.365 V V VIN = 5V, IOUT = 0mA, TJ = 25C (K Package Only) 4.8V VIN 15V, 0 IOUT IFULLOAD (Notes 3, 4, 9) 3.270 3.235 3.300 3.300 3.330 3.365 V V 3.564 3.500 3.528 3.600 3.636 3.672 3.672 V V V 3.672 3.672 3.672 3.672 V V V V VIN = 5V, IOUT = 0mA, TJ = 25C (K Package Only) 5V VIN 15V, 0 IOUT IFULLOAD (Note 9) 5V VIN 15V, 0 IOUT IFULLOAD, TJ 0C (Notes 3, 4, 9) LT1083/4/5-5 IOUT = 0mA, TJ = 25C, VIN = 8V (K Package Only) 0 IOUT IFULLOAD, 6.5V VIN 20V (Notes 4, 6, 7, 9) LT1085-3.6 LT1083/4/5-5 IOUT = 0mA, TJ = 25C, 4.8V VIN 15V 4.8V VIN 15V, IOUT = 0mA, TJ= 25C 4.8V VIN 15V, IOUT = 0mA, TJ= 25C IOUT = 0mA, TJ = 25C, 6.5V VIN 20V (Notes 2, 3) LT1083/4/5-12 IOUT = 0mA, TJ = 25C, 13.5V VIN 25V (Notes 2, 3) Load Regulation LT1084-3.3 LT1085-3.3 LT1085-3.6 LT1083/4/5-5 VIN = 5V, 0 IOUT 5A, TJ = 25C VIN = 5V, 0 IOUT 3A, TJ = 25C VIN = 5.25V, 0 IOUT 3A, TJ = 25C VIN = 8V, 0 IOUT IFULLLOAD, TJ = 25C (Notes 2, 3, 4, 6) LT1083/4/5-12 VIN = 15V, 0 IOUT IFULLLOAD, TJ = 25C (Notes 2, 3, 4, 6) Dropout Voltage Current Limit UNITS 3.270 3.235 5V VIN 15V, 0 IOUT 2.5A (Notes 3, 4, 9) VIN = 4.75V, IOUT = 3A, TJ 0C VIN = 4.75V, IOUT = 2.5A, TJ 0C VIN = 4.75V, IOUT = 1.5A, TJ > 0C LT1085-3.3 MAX LT1085-3.6 LT1084-3.3 TYP IOUT = 0mA, TJ = 25C, VIN = 8V (K Package Only) 4.8V VIN 15V, 0 IOUT IFULLOAD (Notes 3, 4, 9) 3.528 3.350 3.450 3.528 4.950 4.900 5.000 5.000 5.050 5.100 V V 11.880 11.760 12.000 12.000 12.120 12.240 V V 0.5 1.0 6 6 mV mV 0.5 1.0 6 6 mV mV 0.5 1.0 6 6 mV mV 0.5 1.0 10 10 mV mV 1.0 2.0 25 25 mV mV 3 7 15 20 mV mV 3 7 15 20 mV mV 3 7 15 20 mV mV 5 10 20 35 mV mV 12 24 36 72 mV mV LT1083/4/5-12 IOUT = 0mA, TJ = 25C, VIN = 15V (K Package Only) 0 IOUT IFULLOAD, 13.5V VIN 25V (Notes 4, 6, 7, 9) Line Regulation MIN LT1084/5-3.3 VOUT = 33mV, IOUT = IFULL LOAD (Notes 5, 6) 1.3 1.5 V LT1085-3.6 VOUT = 36mV, IOUT = IFULL LOAD (Notes 5, 6) 1.3 1.5 V LT1083/4/5-5 VOUT = 50mV, IOUT = IFULL LOAD (Notes 5, 6) 1.3 1.5 V LT1083/4/5-12 VOUT = 120mV, IOUT = IFULL LOAD (Notes 5, 6) 1.3 1.5 V LT1083-5 VIN = 10V 8.0 9.5 A LT1083-12 VIN = 17V 8.0 9.5 A LT1084-3.3 VIN = 8V 5.5 6.5 A LT1084-5 VIN = 10V 5.5 6.5 A LT1084-12 VIN = 17V 5.5 6.5 A LT1085-3.3/3.6 VIN = 8V LT1085-5 VIN = 10V 3.2 4.0 A 3.2 4.0 A LT1085-12 3.2 4.0 A VIN = 17V 1083ffd 3 LT1083/LT1084/LT1085 Fixed ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. PARAMETER CONDITIONS TYP MAX UNITS Quiescient Current LT1084-3.3 VIN = 18V MIN 5.0 10.0 mA LT1085-3.3 VIN = 18V 5.0 10.0 mA LT1085-3.6 VIN = 18V 5.0 10.0 mA LT1083/4/5-5 VIN 20V 5.0 10.0 mA LT1083/4/5-12 VIN 25V 5.0 10.0 mA 0.002 0.003 0.004 0.010 0.015 0.020 %/W %/W %/W Thermal Regulation LT1083-5/12 TA = 25C, 30ms pulse LT1084-3.3/5/12 LT1085-3.3/3.6/5/12 Ripple Rejection f = 120Hz, COUT = 25F Tantalum, IOUT = IFULLLOAD (Note 4) LT1084-3.3 f = 120Hz, COUT = 25F Tantalum, IOUT = 5A, VIN = 6.3V LT1085-3.3 f = 120Hz, COUT = 25F Tantalum, VIN = 6.3V, IOUT = 3A LT1085-3.6 f = 120Hz, COUT = 25F Tantalum, VIN = 6.6V, IOUT = 3A LT1083/4/5-5 VIN = 8V (Note 6) LT1083/4/5-12 VIN = 15V (Note 6) Temperature Stability 60 60 60 60 54 72 72 72 68 60 dB dB dB dB dB 0.5 % Long Term Stability TA = 125C, 1000 Hrs. 0.03 RMS Output Noise (% of VOUT) TA = 25C, 10Hz = f 10kHz 0.003 Thermal Resistance Junctrion-to-Case Control Circuitry/Power Transistor (See Applications Information) LT1083 K Package P Package 1.0 % % 0.6/1.6 0.5/1.6 C/W C/W LT1084 K Package P Package T Package 0.75/2.3 0.65/2.3 0.65/2.7 C/W C/W C/W LT1085 K Package T Package DD Package 0.9/3.0 0.7/3.0 0.7/3.0 C/W C/W C/W Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: See thermal regulation specifications for changes in output voltage due to heating effects. Load and line regulation are measured at a constant junction temperature by low duty cycle pulse testing. Note 3: Line and load regulation are guaranteed up to the maximum power dissipation (60W for the LT1083, 45W for the LT1084 (K, P), 30W for the LT1084 (T) and 30W for the LT1085). Power dissipation is determined by the input/output differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range. Note 4: IFULL LOAD is defined in the current limit curves. The IFULLLOAD curve is defined as the minimum value of current limit as a function of input to output voltage. Note that the 60W power dissipation for the LT1083 (45W for the LT1084 (K, P), 30W for the LT1084 (T), 30W for the LT1085) is only achievable over a limited range of input to output voltage. Note 5: Dropout voltage is specified over the full output current range of the device. Test points and limits are shown on the Dropout Voltage curve. Note 6: For LT1083 IFULL LOAD is 5A for - 55C TJ - 40C and 7.5A for TJ - 40C. Note 7: 1.7V (VIN - VOUT) 25V for LT1084 at - 55C TJ - 40C. Note 8: Dropout voltage 1.7V maximum for LT1084 at - 55C TJ - 40C. Note 9: Full load current is not available at all input-output voltages. See Notes 3, 4, 6. 1083ffd 4 LT1083/LT1084/LT1085 Fixed U W TYPICAL PERFOR A CE CHARACTERISTICS LT1083 Short-Circuit Current -40C TJ 150C 0C TJ 125C 1 TJ = 150C TJ = 25C TJ = -55C 25C 10 150C 8 6 -55C 4 2 IFULL LOAD GUARANTEED 1 2 3 4 5 6 7 8 OUTPUT CURRENT (A) 9 10 0 20 30 15 25 5 10 INPUT/OUTPUT DIFFERENTIAL (V) LT1084 Dropout Voltage 35 TJ = -55C TJ = 25C 7 150C 25C 6 -55C 5 4 3 IFULL LOAD GUARANTEED 2 5 0 6 20 15 10 25 30 5 INPUT/OUTPUT DIFFERENTIAL (V) 0.05 0 -0.05 -0.10 -0.15 35 LT1085 Dropout Voltage SHORT-CIRCUIT CURRENT (A) TJ = 25C TJ = 150C 0 OUTPUT VOLTAGE DEVIATION (%) INDICATES GUARANTEED TEST POINT 3 2 1 OUTPUT CURRENT (A) LT1085 Load Regulation 0.10 6 TJ = -55C 5 25C 4 150C 3 -55C 2 IFULL LOAD GUARANTEED 1 0 4 LT1083/4/5 FIXED G07 25 50 75 100 125 150 TEMPERATURE (C) LT1083/4/5 FIXED G06 LT1085 Short-Circuit Current 2 0C TJ 125C 0 LT1083/4/5 FIXED G05 LT1083/4/5 FIXEDG04 -55C TJ 150C 25 50 75 100 125 150 TEMPERATURE (C) I = 5A -0.20 -50 -25 0 0 3 4 2 OUTPUT CURRENT (A) 0 LT1084 Load Regulation 8 1 0 -0.15 0.10 OUTPUT VOLTAGE DEVIATION (%) SHORT-CIRCUIT CURRENT (A) 1 1 -0.10 9 0C TJ 125C 1 -0.05 LT1084 Short Circuit Current INDICATES GUARANTEED TEST POINT 0 0 LT1083/4/5 FIXED G03 10 TJ = 150C 0.05 LT1083/4/5 FIXED G02 2 -55C TJ 150C I = 7.5A -0.20 -50 -25 0 0 LT1083/4/5 FIXED G01 MINIMUN INPUT/OUTPUT DIFFERENTIAL (V) OUTPUT VOLTAGE DEVIATION (%) INDICATES GUARANTEED TEST POINT 0 MINIMUM INPUT/OUTPUT DIFFERENTIAL (V) LT1083 Load Regulation 0.10 12 SHORT-CIRCUIT CURRENT (A) MINIMUM INPUT/OUTPUT DIFFERENTIAL (V) LT1083 Dropout Voltage 2 0 20 30 15 25 5 10 INPUT/OUTPUT DIFFERENTIAL (V) 35 LT1083/4/5 FIXED G08 I = 3A 0.05 0 -0.05 -0.10 -0.15 -0.20 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) LT1083/4/5 FIXED G09 1083ffd 5 LT1083/LT1084/LT1085 Fixed U W TYPICAL PERFOR A CE CHARACTERISTICS LT1083/4/5-5 Ripple Rejection vs Current LT1083/4/5-5 Ripple Rejection 70 VRIPPLE 0.5VP-P 60 (VIN - VOUT) 3V 50 2.0 90 80 (VIN - VOUT) VDROPOUT 40 30 20 OUTPUT VOLTAGE CHANGE (%) VRIPPLE 3VP-P Temperature Stability 100 RIPPLE REJECTION (dB) RIPPLE REJECTION (dB) 80 fR = 120Hz VRIPPLE 3VP-P 70 fR = 20kHz VRIPPLE 0.5VP-P 60 50 40 30 20 10 0 100k 0 0.8 0.2 0.6 0.4 OUTPUT CURRENT (0 TO IFULLLOAD) 1083/4/5 FIXED G10 -2.0 -50 -25 1.0 100 100 90 90 30 (VIN - VOUT) VDROPOUT 20 10 IOUT = IFULLLOAD 0 10 100 1k 10k FREQUENCY (Hz) 100k 80 fR = 120Hz VRIPPLE 3VP-P 70 70 POWER (W) 40 RIPPLE REJECTION (dB) RIPPLE REJECTION (dB) (VIN - VOUT) 3V 50 25 50 75 100 125 150 TEMPERATURE (C) LT1083 Maximum Power Dissipation* 80 60 0 LT1183/4/5 FIXED G12 LT1083/4/5-12 Ripple Rejection vs Current VRIPPLE 0.5VP-P 70 -1.0 1083/4/5 FIXED G11 LT1083/4/5-12 Ripple Rejection VRIPPLE 3VP-P 0 10 IOUT = IFULLLOAD 0 10 100 1k 10k FREQUENCY (Hz) 80 1.0 60 fR = 20kHz VRIPPLE 0.5VP-P 50 40 50 40 30 30 20 20 10 10 0 0 0 0.8 0.2 0.6 0.4 OUTPUT CURRENT (0 TO IFULLLOAD) 1083/4/5 FIXED G13 1.0 1083/4/5 FIXED G14 LT1083MK 60 LT1083CP LT1083CK 50 60 70 80 90 100 110 120 130 140 150 CASE TEMPERATURE (C) * AS LIMITED BY MAXIMUM JUNCTION TEMPERATURE LT1083/4/5 FIXED G15 LT1085 Maximum Power Dissipation* LT1084 Maximum Power Dissipation* 60 50 50 40 LT1084MK 30 LT1084CT LT1084CP 20 10 POWER (W) POWER (W) 40 30 LT1085MK 20 LT1085CT 10 LT1084CK LT1085CK 0 0 50 60 70 80 90 100 110 120 130 140 150 CASE TEMPERATURE (C) * AS LIMITED BY MAXIMUM JUNCTION TEMPERATURE 50 60 70 80 90 100 110 120 130 140 150 CASE TEMPERATURE (C) * AS LIMITED BY MAXIMUM JUNCTION TEMPERATURE LT1083/4/5 FIXED G16 LT1083/4/5 FIXED G17 1083ffd 6 LT1083/LT1084/LT1085 Fixed W BLOCK DIAGRA VIN + - THERMAL LIMIT VOUT GND LT1083/4/5 BD U W U U APPLICATIO S I FOR ATIO The LT1083 family of three-terminal regulators are easy to use and have all the protection features that are expected in high performance voltage regulators. They are short circuit protected, have safe area protection as well as thermal shutdown to turn off the regulator should the temperature exceed about 165C. These regulators offer lower dropout voltage and more precise reference tolerance. Further, the reference stability with temperature is improved over older types of regulators. The only circuit difference between using the LT1083 family and older regulators is that they require an output capacitor for stability. Stability The circuit design used in the LT1083 family requires the use of an output capacitor as part of the device frequency compensation. For all operating conditions, the addition of 150F aluminum electrolytic or a 22F solid tantalum on the output will ensure stability. Normally capacitors much smaller than this can be used with the LT1083. Many different types of capacitors with widely varying charac- teristics are available. These capacitors differ in capacitor tolerance (sometimes ranging up to 100%), equivalent series resistance, and capacitance temperature coefficient. The 150F or 22F values given will ensure stability. Normally, capacitor values on the order of 100F are used in the output of many regulators to ensure good transient response with heavy load current changes. Output capacitance can be increased without limit and larger values of output capacitance further improve stability and transient response of the LT1083 regulators. Another possible stability problem that can occur in monolithic IC regulators is current limit oscillations. These can occur because in current limit the safe area protection exhibits a negative impedance. The safe area protection decreases the current limit as the input-tooutput voltage increases.That is the equivalent of having a negitive resistance since increasing voltage causes current to decrease. Negitive resistance during current limit is not unique to the LT1083 series and has been present on all power IC regulators. The value of negative resistance is a function of how fast the current limit is 1083ffd 7 LT1083/LT1084/LT1085 Fixed U W U U APPLICATIO S I FOR ATIO folded back as input-to-output voltage increases. This negative resistance can react with capacitors or inductors on the input to cause oscillations during current limiting. Depending on the value of series resistance, the overall circuitry may end up unstable. Since this is a system problem, it is not necessarily easy to solve; however it does not cause any problems with the IC regulator and can usually be ignored. up into very heavy loads. During the start-up, as the input voltage is rising, the input-to-output voltage differential remains small allowing the regulator to supply large output currents. With high input voltage a problem can occur wherein removal of an output short will not allow the output voltage to recover. Older regulators such as the 7800 series, also exhibited this phenomenon so it is not unique to the LT1083. Protection Diodes The problem occurs with a heavy output load when the input voltage is high and the output voltage is low, such as immediately after a removal of a short. The load line for such a load may intersect the output current curve at two points. If this happens there are two stable output operating points for the regulator. With this double intersection the power supply may need to be cycled down to zero and brought up again to make the output recover. In normal operation the LT1083 family does not need any protection diodes, The internal diode between the input and the output pins of the LT1083 family can handle microsecond surge currents of 50A to 100A. Even with large output capacitances it is very difficult to get those values of surge current in normal operation. Only with high value output capacitors, such as 1000F to 5000F and with the input pin instantaneously shorted to ground, can damage occur. A crowbar circuit at the input of the LT1083 can generate those kinds of currents and a diode from output-to-input is then recommended. Normal power supply cycling or even plugging and unplugging in the system will not generate currents large enough to do any damage. D1 1N4002 (OPTIONAL) Ripple Rejection In applications that require improved ripple rejection the LT1083 series adjustable regulators should be used. With LT1083 series adjustable regulators the addition of a bypass capacitor from the adjust pin to ground will reduce output ripple by the ratio of VOUT/1.25V. See LT1083 series adjustable regulator data sheet. Load Regulation VIN IN LT1083 ADJ OUT VOUT + COUT 150F 1083/4/5 AI01 Overload Recovery Like any of the IC power regulators, the LT1083 has safe area protection. The safe area protection decreases the current limit as input-to-output voltage increases and keeps the power transistor inside a safe operating region for all values of input-to-output voltage. The LT1083 protection is designed to provide some output current at all values of input-to-output voltage up to the device breakdown. When power is first turned on, as the input voltage rises, the output follows the input, allowing the regulator to start Because the LT1083 is a three-terminal device, it is not possible to provide true remote load sensing. Load regulation will not be limited by the resistance of the wire connecting the regulator to the load. The data sheet specification for the load regulation is measured at the bottom of the package. Negative side sensing is a true Kelvin connection, with the ground pin of the device returned to the negative side of the load. Thermal Considerations The LT1083 series of regulators have internal power and thermal limiting circuitry designed to protect the device under overload conditions. For continuous normal load conditions however, maximum junction temperature ratings must not be exceeded. It is important to give careful consideration to all sources of thermal resistance from junction to ambient. This includes junction-to-case, 1083ffd 8 LT1083/LT1084/LT1085 Fixed U W U U APPLICATIO S I FOR ATIO case- to-heat sink interface, and heat sink resistance itself. New thermal resistance specifications have been developed to more accurately reflect device temperature and ensure safe operating temperatures. The data section for these new regulators provides a separate thermal resistance and maximum junction temperature for both the Control Section and the Power Section. Previous regulators, with a single junction-to-case thermal resistance specification, used an average of the two values provided here and therefore could allow excessive junction temperatures under certain conditions of ambient temperature and heat sink resistance. To avoid this possibility, calculations should be made for both sections to ensure that both thermal limits are met. Junction-to-case thermal resistance is specified from the IC junction to the bottom of the case directly below the die. This is the lowest resistance path for heat flow. Proper mounting is required to ensure the best possible thermal flow from this area of the package to the heat sink. Thermal compound at the case-to-heat sink interface is strongly recommended. If the case of the device must be electronically isolated, a thermally conductive spacer can be used as long as its added contribution to thermal resistance is considered. Note that the case of all devices in this series is electronically connected to the ouput. For example, using a LT1083-5CP (TO-3P, Commercial) and assuming: VIN(max continuous) = 9V, VOUT = 5V, IOUT = 6A, TA = 75C, HEAT SINK = 1C/W, CASE-TO-HEAT SINK = 0.2C/W for P package with thermal compound. Power dissipation under these conditions is equal to: PD = (VIN - VOUT) (IOUT) = 24W Junction temperature will be equal to: TJ = TA + PD (HEAT SINK + CASE-TO-HEAT SINK + JC) For the Control Section: TJ = 75C + 24W (1C/W + 0.2C/W + 0.5C/W) = 118C 118C < 125C = TJMAX (Control Section Commercial Range) For the Power Transistor: TJ = 75C + 24W (1C/W + 0.2C/W + 1.6C/W) = 142C 142C < 150C = TJMAX (Power Transistor Commercial Range) In both cases the junction temperature is below the maximum rating for the respective sections, ensuring reliable operation. U TYPICAL APPLICATIO S High Efficiency Regulator Paralleling Regulators 1mH 28V INPUT IN + OUTPUT VIN IN GND 10,000F 10k LT1083-5 OUT GND VOUT = 5V IOUT = 0A TO 15A 470 MR1122 0.015 1N914 28V IN LT1083-5 OUT GND 1k 2 FEET #18 WIRE* LT1083-5 OUT 1M 4N28 LT1083/4/5 TA04 LT1083/4/5 TA03 10k + *THE #18 WIRE ACTS AS BALLAST RESISTANCE INSURING CURRENT SHARING BETWEEN BOTH DEVICES LT1011 10k - 28V 1N914 1083ffd 9 LT1083/LT1084/LT1085 Fixed U TYPICAL APPLICATIO S 7.5A Regulator T1 TRIAD F-269U L 1MH C30B IN 20 3 110VAC 20 T2 1 1N4003 4 12V 0A TO 7.5A LT1083-12 OUT + C1 GND + 50,000F 100F 2 LT1004-1.2 C30B 1N4003 1N4003 1N914 16k* 1F 82k 560 15k 8 2 -15V 4 + 3 - 7 0.1F 1 NC 1N4148 100pF 15V 8 -15V 4 7 * 1% FILM RESISTOR L-DALE TO-5 TYPE T2-STANCOR 11Z-2003 11k* 200k LT1011 10k 16k* 15V 2N3904 - 3 1 8 LT1011 + 10k 2 6 + 1 2 4 -15V 15V REGULATOR WITH SCR PREREGULATOR TO LOWER POWER DISSIPATION. ABOUT 1.7V DIFFERENTIAL IS MAINTAINED ACROSS THE LT1083 INDEPENDENT OF LOAD CURRENT. - 7 15k 3 LM301A 15V 11k* LT1083/4/5 TA05 1F U PACKAGE DESCRIPTIO K Package 2-Lead TO-3 Metal Can T Package 3-Lead Plastic TO-220 (LTC DWG # 05-08-1310) (LTC DWG # 05-08-1420) .760 - .775 (19.30 - 19.69) .320 - .350 (8.13 - 8.89) .060 - .135 (1.524 - 3.429) .147 - .155 (3.734 - 3.937) DIA .390 - .415 (9.906 - 10.541) .165 - .180 (4.191 - 4.572) .045 - .055 (1.143 - 1.397) .230 - .270 (5.842 - 6.858) .420 - .480 (10.67 - 12.19) .460 - .500 (11.684 - 12.700) .038 - .043 (0.965 - 1.09) .570 - .620 (14.478 - 15.748) .330 - .370 (8.382 - 9.398) .980 - 1.070 (24.892 - 27.178) 1.177 - 1.197 (29.90 - 30.40) .655 - .675 (16.64 - 17.15) .210 - .220 (5.33 - 5.59) .151 - .161 (3.86 - 4.09) DIA, 2PLCS .167 - .177 (4.24 - 4.49) R .425 - .435 (10.80 - 11.05) .067 - .077 (1.70 - 1.96) .490 - .510 (12.45 - 12.95) R .520 - .570 (13.208 - 14.478) .100 (2.540) BSC .218 - .252 (5.537 - 6.401) .013 - .023 (0.330 - 0.584) .028 - .038 (0.711 - 0.965) .050 (1.270) TYP .095 - .115 (2.413 - 2.921) T3 (TO-220) 0801 K2 (TO-3) 0801 OBSOLETE PACKAGE 1083ffd 10 LT1083/LT1084/LT1085 Fixed U PACKAGE DESCRIPTIO M Package 3-Lead Plastic DD Pak (LTC DWG # 05-08-1460) .256 (6.502) .060 (1.524) TYP .060 (1.524) .390 - .415 (9.906 - 10.541) .165 - .180 (4.191 - 4.572) .045 - .055 (1.143 - 1.397) 15 .060 (1.524) .183 (4.648) .330 - .370 (8.382 - 9.398) +.008 .004 -.004 +0.203 0.102 -0.102 ( .059 (1.499) ) .095 - .115 (2.413 - 2.921) .075 (1.905) .300 (7.620) +.012 .143 -.020 +0.305 3.632 -0.508 ( BOTTOM VIEW OF DD PAK HATCHED AREA IS SOLDER PLATED COPPER HEAT SINK ) .050 (1.270) .100 (2.54) BSC .050 .012 (1.270 0.305) .013 - .023 (0.330 - 0.584) .420 .080 .420 .276 .325 .350 .205 .565 .565 .320 .090 NOTE: 1. DIMENSIONS IN INCH/(MILLIMETER) 2. DRAWING NOT TO SCALE .090 .100 .070 .100 RECOMMENDED SOLDER PAD LAYOUT M (DD3) 0204 .070 RECOMMENDED SOLDER PAD LAYOUT FOR THICKER SOLDER PASTE APPLICATIONS P Package 3-Lead Plastic TO-3P (Similar to TO-247) (LTC DWG # 05-08-1450) .560 (14.224) .325 (8.255) .580 (14.732) .700 (17.780) .830 - .870 (21.08 - 22.10) .580 - .6OO (14.73 - 15.24) .098 (2.489) .124 (3.149) .187 - .207 (4.75 - 5.26) .620 - .64O (15.75 - 16.26) .275 (6.985) MOUNTING HOLE 18 - 22 .115 - .145 (2.92 - 3.68) DIA .060 - .080 (1.52 - 2.03) .170 - .2OO (4.32 - 5.08) EJECTOR PIN MARKS .105 - .125 (2.67 - 3.18) DIA 3 - 7 .170 (4.32) MAX .780 - .800 (19.81 - 20.32) BOTTOM VIEW OF TO-3P HATCHED AREA IS SOLDER PLATED COPPER HEAT SINK .042 - .052 (1.07 - 1.32) .074 - .084 (1.88 - 2.13) .215 (5.46) BSC .113 - .123 (2.87 - 3.12) Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. .087 - .102 (2.21 - 2.59) .020 - .040 (0.51 - 1.02) P3 0801 1083ffd 11 LT1083/LT1084/LT1085 Fixed U TYPICAL APPLICATIO S Adjusting Output Voltage VIN > 12V Regulator with Reference LT1085-5 VIN > 11.5V 5V to 10V + + + + 100F 10F 10V LT1085-5 100F 10F 5VOUT + 10F* LT1029 1k LT1083/4/5 TA07 LT1083/4/5 TA06 *OPTIONAL IMPROVES RIPPLE REJECTION Low Dropout Negative Supply Battery Backed Up Regulated Supply VIN IN VIN + LT1084-12 OUT 10F 50 GND + + 100F 10,000F LT1083/4/5 TA08 FLOATING INPUT 5.2V LINE 5.0V BATTERY LT1084-5 SELECT FOR CHARGE RATE VOUT = -12V LT1084-5 6.5V + + 10F 100F LT1083/4/5 TA09 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1129 700mA Micropower Low Dropout Regulator 50A Quiescent Current LT1175 500mA Negative Low Dropout Micropower Regulator 45A IQ, 0.26V Dropout Voltage, SOT-223 Package LT1374 4.5A, 500kHz Step-Down Converter 4.5A, 0.07 Internal Switch, SO-8 Package LT1529 3A Low Dropout Regulator with 50A IQ 500mV Dropout Voltage LT1573 UltraFastTM Transient Response Low Dropout Regulator Drives External PNP LT1575 UltraFast Transient Response Low Dropout Regulator Drives External N-Channel MOSFET LT1580 7A, Very Low Dropout Regulator 0.54V Dropout at 7A, Fixed 2.5VOUT and Adjustable LT1581 10A, Very Low Dropout Regulator 0.63V Dropout at 10A, Fixed 2.5VOUT and Adjustable LT1584/85/87 7A/4.6A/3A Fast Response LDOs Fast Transient Response for Microprocessor Applications LT1735 Synchronous Step-Down Converter High Efficiency, OPTI-LOOPTM Compensation LT1761 Series 100mA, Low Noise, Low Dropout Micropower Regulators in SOT-23 20A Quiescent Current, 20VRMS Noise, SOT-23 Package LT1762 Series 150mA, Low Noise, LDO Micropower Regulators 25A Quiescent Current, 20VRMS Noise, MSOP Package LT1763 Series 500mA, Low Noise LDO Micropower Regulators 30A Quiescent Current, 20VRMS Noise, SO-8 Package LT1764 3A Low Noise Fast Transient Response LDO 40VRMS Noise, 5-Lead DD Package LT1962 300mA, Low Noise LDO Micropower Regulator 20VRMS Noise, MSOP Package LT1963 1.5A, Low Noise, Fast Transient Response LDO 40VRMS Noise, SOT-223 Package UltraFast and OPTI-LOOP are trademarks of Linear Technology Corporation. 1083ffd 12 Linear Technology Corporation LT 1007 REV D * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 1994