SN75LVDS83B www.ti.com SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 FLATLINKTM TRANSMITTER Check for Samples: SN75LVDS83B FEATURES 1 * 2 * * * * * * * * LVDS Display Serdes Interfaces Directly to LCD Display Panels with Integrated LVDS Package Options: 4.5mm x 7mm BGA, and 8.1mm x 14mm TSSOP 1.8V up to 3.3V Tolerant Data Inputs to Connect Directly to Low-Power, Low-Voltage Application and Graphic Processors Transfer Rate up to 135Mpps (Mega Pixel Per Second); Pixel Clock Frequency Range 10MHz to 135MHz Suited for Display Resolutions Ranging From HVGA up to HD With Low EMI Operates From a Single 3.3V Supply and 170mW (typ.) at 75MHz 28 Data Channels Plus Clock In Low-Voltage TTL to 4 Data Channels Plus Clock Out Low- * * * Voltage Differential Consumes Less Than 1mW When Disabled Selectable Rising or Falling Clock Edge Triggered Inputs ESD: 5kV HBM Support Spread Spectrum Clocking (SSC) Compatible with all OMAPTM2x, OMAPTM3x, and DaVinciTM Application Processors APPLICATIONS * * * LCD Display Panel Driver UMPC and Netbook PC Digital Picture Frame DESCRIPTION The SN75LVDS83B FlatLinkTM transmitter contains four 7-bit parallel-load serial-out shift registers, a 7X clock synthesizer, and five Low-Voltage Differential Signaling (LVDS) line drivers in a single integrated circuit. These functions allow 28 bits of single-ended LVTTL data to be synchronously transmitted over five balanced-pair conductors for receipt by a compatible receiver, such as the SN75LVDS82 and LCD panels with integrated LVDS receiver. When transmitting, data bits D0 through D27 are each loaded into registers upon the edge of the input clock signal (CLKIN). The rising or falling edge of the clock can be selected via the clock select (CLKSEL) pin. The frequency of CLKIN is multiplied seven times, and then used to unload the data registers in 7-bit slices and serially. The four serial streams and a phase-locked clock (CLKOUT) are then output to LVDS output drivers. The frequency of CLKOUT is the same as the input clock, CLKIN. swiv Application processor TM (e.g. OMAP ) el SN75LVDS83B TM FlatLink Transmitter Package Options TSSOP: 8 x 14mm DGG BGA: 4.5 x 7mm 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. OMAP, DaVinci, FlatLink are trademarks of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2009-2011, Texas Instruments Incorporated SN75LVDS83B SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. DESCRIPTION (CONTINUED) The SN75LVDS83B requires no external components and little or no control. The data bus appears the same at the input to the transmitter and output of the receiver with the data transmission transparent to the user(s). The only user intervention is selecting a clock rising edge by inputting a high level to CLKSEL or a falling edge with a low-level input, and the possible use of the Shutdown/Clear (SHTDN). SHTDN is an active-low input to inhibit the clock, and shut off the LVDS output drivers for lower power consumption. A low-level on this signal clears all internal registers to a low-level. The SN75LVDS83B is characterized for operation over ambient air temperatures of -10C to 70C. Alternative device option: The SN75LVDS83A (SLLS980) is an alternative to the SN75LVDS83B for clock frequency range of 10MHz-100MHz only. The SN75LVDS83A is available in the TSSOP package option only. ORDERING INFORMATION (1) (1) PART NUMBER PART MARKING PACKAGE SN75LVDS83BZQLR LVDS83B in BGA package 56-pin ZQL LARGE T&R SN75LVDS83BDGG LVDS83B in TSSOP package 56-pin DGG TUBE SN75LVDS83BDGGR LVDS83B in TSSOP package 56-pin DGG LARGE T&R For the most current package and ordering information, see the Package Option Addendum located at the end of this data sheet, or refer to our web site at www.ti.com. ABSOLUTE MAXIMUM RATINGS (1) Supply voltage range, VCC, IOVCC, LVDSVCC, PLLVCC (2) Voltage range at any output terminal Voltage range at any input terminal Continuous power dissipation Storage temperature, Ts (1) (2) (3) (4) (5) 2 UNIT V -0.5 to VCC + 0.5 V -0.5 to IOVCC + 0.5 V See the dissipation rating table -65 to 150 C 5 kV Charged Device Model (CDM) (4) all pins 500 V Machine Model (MM) (5) all pins 150 V Human Body Model (HBM) (3) all pins ESD rating VALUE -0.5 to 4 Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. All voltages are with respect to the GND terminals. In accordance with JEDEC Standard 22, Test Method A114-A. In accordance with JEDEC Standard 22, Test Method C101. In accordance with JEDEC Standard 22, Test Method A115-A. Copyright (c) 2009-2011, Texas Instruments Incorporated SN75LVDS83B www.ti.com SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 RECOMMENDED OPERATING CONDITIONS over operating free-air temperature range (unless otherwise noted) PARAMETER MIN NOM MAX Supply voltage, VCC 3 3.3 3.6 LVDS output Supply voltage, LVDSVCC 3 3.3 3.6 PLL analog supply voltage, PLLVCC 3 3.3 3.6 1.62 1.8 / 2.5 / 3.3 3.6 IO input reference supply voltage, IOVCC Power supply noise on any VCC terminal UNIT V 0.1 High-level input voltage, VIH Low-level input voltage, VIL IOVCC = 1.8V IOVCC/2 + 0.3V IOVCC = 2.5V IOVCC/2 + 0.4V IOVCC = 3.3V IOVCC/2 + 0.5V V IOVCC = 1.8V IOVCC/2 - 0.3V IOVCC = 2.5V IOVCC/2 - 0.4V IOVCC = 3.3V Differential load impedance, ZL Operating free-air temperature, TA V IOVCC/2 - 0.5V 90 132 -10 70 C DISSIPATION RATINGS PACKAGE CIRCUIT BOARD MODEL (1) DGG ZQL DGG (3) ZQL (1) (2) (3) Low-K High-K TJA 25C DERATING FACTOR (2) ABOVE TJA = 25C TJA = 70C POWER RATING 1111mW 12.3mW/C 555mW 1034mW 11.5mW/C 517mW 1730mW 19mW/C 865mW 2000mW 22mW/C 1000mW In accordance with the High-K and Low-K thermal metric definitions of EIA/JESD51-2. This is the inverse of the junction-to-ambient thermal resistance when board-mounted and with no air flow. DGG junction to case thermal reistance (JC) is 15.4C/W. TIMING REQUIREMENTS PARAMETER Input clock period, tc Input clock modulation MIN MAX UNIT 7.4 100 ns with modulation frequency 30kHz 8% with modulation frequency 50kHz High-level input clock pulse width duration, tw 6% 0.4 tc Input signal transition time, tt Data set up time, D0 through D27 before CLKIN (See Figure 3) Data hold time, D0 through D27 after CLKIN Copyright (c) 2009-2011, Texas Instruments Incorporated 0.6 tc ns 3 ns 2 ns 0.8 ns 3 SN75LVDS83B SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 www.ti.com DGG PACKAGE (TOP VIEW) IOVCC 1 56 D5 2 3 55 54 D7 GND D8 4 53 5 52 GND D1 6 51 D0 D9 D10 7 50 8 49 D27 GND VCC D11 9 10 48 47 D12 11 46 D13 12 45 Y1P GND D14 13 44 14 15 43 42 LVDSVCC GND Y2M 16 41 17 18 40 39 19 38 D19 GND 20 37 CLKOUTP Y3M Y3P 21 36 GND D20 35 34 GND D21 22 23 D22 24 33 D23 25 32 IOVCC D24 D25 26 31 27 30 28 29 D6 D15 D16 CLKSEL D17 D18 D4 D3 D2 Y0M Y0P Y1M Y2P CLKOUTM PLLVCC GND SHTDN CLKIN D26 GND DGG PIN LIST 4 Pin # Signal Pin # Signal Pin # Signal Pin # 1 IOVCC 15 D15 29 GND 43 Signal GND 2 D5 16 D16 30 D26 44 LVDSVCC 3 D6 17 CLKSEL 31 CLKIN 45 Y1P 4 D7 18 D17 32 SHTDN 46 Y1M 5 GND 19 D18 33 GND 47 Y0P 6 D8 20 D19 34 PLLVCC 48 Y0M 7 D9 21 GND 35 GND 49 GND 8 D10 22 D20 36 GND 50 D27 9 VCC 23 D21 37 Y3P 51 D0 10 D11 24 D22 38 Y3M 52 D1 11 D12 25 D23 39 CLKOUTP 53 GND 12 D13 26 IOVCC 40 CLKOUTM 54 D2 13 GND 27 D24 41 Y2P 55 D3 14 D14 28 D25 42 Y2M 56 D4 Copyright (c) 2009-2011, Texas Instruments Incorporated SN75LVDS83B www.ti.com SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 ZQL PACKAGE (TOP VIEW) 6 5 4 3 2 1 D8 D7 D5 D4 D2 D1 D9 GND D6 D3 D0 D27 D11 VCC D10 GND Y0P Y0M D13 D12 IOVCC GND Y1P Y1M D14 GND GND D16 D15 Y2P Y2M D17 D18 CLKSEL GND CLKP CLKM D19 GND IOVCC GND Y3P Y3M D20 D21 D25 SHTDN PLLVCC GND D22 D23 D24 D26 CLKIN GND K J H G F LVDSVCC E D C B A ZQL PIN LIST Ball # Signal Ball # Signal Ball # Signal A1 GND A2 CLKIN A3 D26 A4 D24 A5 D23 A6 D22 B1 GND B2 PLLVCC B3 SHTDN B4 D25 B5 D21 B6 D20 C1 Y3M C2 Y3P C3 GND C4 IOVCC C5 GND C6 D19 D1 CLKM D2 CLKP D3 GND D4 CLKSEL D5 D18 D6 D17 E1 Y2M E2 Y2P E3 ball not populated E4 ball not populated E5 D15 E6 D16 F1 LVDSVCC F2 GND F3 ball not populated F4 ball not populated F5 GND F6 D14 G1 Y1M G2 Y1P G3 GND G4 IOVCC G5 D12 G6 D13 H1 Y0M H2 Y0P H3 GND H4 D10 H5 VCC H6 D11 J1 D27 J2 D0 J3 D3 J4 D6 J5 GND J6 D9 Copyright (c) 2009-2011, Texas Instruments Incorporated 5 SN75LVDS83B SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 www.ti.com ZQL PIN LIST (continued) K1 D1 K2 D2 K3 D4 K4 D5 K5 D7 K6 D8 PIN FUNCTIONS TERMINAL I/O Y0P, Y0M, Y1P, Y1M, Y2P, Y2M Y3P, Y3M DESCRIPTION Differential LVDS data outputs. Outputs are high-impedance when SHTDN is pulled low (de-asserted) LVDS Out Differential LVDS Data outputs. Output is high-impedance when SHTDN is pulled low (de-asserted). Note: if the application only requires 18-bit color, this output can be left open. CLKP, CLKM Differential LVDS pixel clock output. Output is high-impedance when SHTDN is pulled low (de-asserted). D0 - D27 Data inputs; supports 1.8V to 3.3V input voltage selectable by VDD supply. To connect a graphic source successfully to a display, the bit assignment of D[27:0] is critical (and not necessarily intuitive). For input bit assignment see Figure 14 to Figure 17 for details. Note: if application only requires 18-bit color, connect unused inputs D5, D10, D11, D16, D17, D23, and D27 to GND. CLKIN CMOS IN with pulldn Input pixel clock; rising or falling clock polarity is selectable by Control input CLKSEL. SHTDN Device shut down; pull low (de-assert) to shut down the device (low power, resets all registers) and high (assert) for normal operation. CLKSEL Selects between rising edge input clock trigger (CLKSEL = VIH) and falling edge input clock trigger (CLKSEL = VIL). VCC 3.3V digital supply voltage IOVCC PLLVCC I/O supply reference voltage (1.8V up to 3.3V matching the GPU data output signal swing) Power Supply (1) 3.3V PLL analog supply LVDSVCC 3.3V LVDS output analog supply GND Supply ground for VCC, IOVCC, LVDSVCC, and PLLVCC. (1) 6 For a multilayer pcb, it is recommended to keep one common GND layer underneath the device and connect all ground terminals directly to this plane. Copyright (c) 2009-2011, Texas Instruments Incorporated SN75LVDS83B www.ti.com SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 FUNCTIONAL BLOCK DIAGRAM Parallel-Load 7-bit Shift Register D0, D1, D2, D3, D4, D6, D7 7 A,B,...G SHIFT/LOAD >CLK Y0P Y0M Parallel-Load 7-bit Shift Register D8, D9, D12, D13, D14, D15, D18 7 A,B,...G SHIFT/LOAD >CLK Y1P Y1M Parallel-Load 7-bit Shift Register D19, D20, D21, D22, D24, D25, D26 7 A,B,...G SHIFT/LOAD >CLK Y2P Y2M Parallel-Load 7-bit Shift Register D27, D5, D10, D11, D16, D17, D23 7 A,B,...G SHIFT/LOAD >CLK Y3P Y3M Control Logic SHTDN 7X Clock/PLL 7XCLK CLKIN >CLK CLKINH CLKSEL Copyright (c) 2009-2011, Texas Instruments Incorporated CLKOUTP CLKOUTM RISING/FALLING EDGE 7 SN75LVDS83B SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 www.ti.com Dn CLKIN or CLKIN CLKOUT Previous cycle Next Current cycle Y0 D0-1 D7 D6 D4 D3 D2 D1 D0 D7+1 Y1 D8-1 D18 D15 D14 D13 D12 D9 D8 D18+1 Y2 D19-1 D26 D25 D24 D22 D21 D20 D19 D26+1 Y3 D27-1 D23 D17 D16 D11 D10 D5 D27 D23+1 Figure 1. Typical SN75LVDS83B Load and Shift Sequences LVDSVCC IOVCC 5W D or SHTDN 50W 7V YnP or YnM 10kW 300kW 7V Figure 2. Equivalent Input and Output Schematic Diagrams 8 Copyright (c) 2009-2011, Texas Instruments Incorporated SN75LVDS83B www.ti.com SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 ELECTRICAL CHARACTERISTICS over operating free-air temperature range (unless otherwise noted) PARAMETER VT Input voltage threshold |VOD| Differential steady-state output voltage magnitude TEST CONDITIONS MIN TYP (1) MAX IOVCC/2 250 UNIT V 450 mV RL = 100, See Figure 4 |VOD| Change in the steady-state differential output voltage magnitude between opposite binary states VOC(SS) Steady-state common-mode output voltage VOC(PP) Peak-to-peak common-mode output voltage IIH High-level input current VIH = IOVCC IIL Low-level input current VIL = 0 V 10 A VOY = 0 V 24 mA 1 See Figure 4 tR/F (Dx, CLKin) = 1ns 1.125 35 1.375 mV V 35 mV 25 A IOS Short-circuit output current VOD = 0 V 12 mA IOZ High-impedance state output current VO = 0 V to VCC 20 A Rpdn Input pull-down integrated resistor on all inputs (Dx, CLKSEL, SHTDN, CLKIN) IOVCC = 1.8V 200 IOVCC = 3.3V 100 IQ Quiescent current (average) disabled, all inputs at GND; SHTDN = VIL 2 k 100 A SHTDN = VIH, RL = 100 (5 places), grayscale pattern (Figure 5) VCC = 3.3V, fCLK = 75MHz I(VCC) + I(PLLVCC) + I(LVDSVCC) 51.9 I(IOVCC) with IOVCC = 3.3V 0.4 I(IOVCC) with IOVCC = 1.8V 0.1 mA SHTDN = VIH, RL = 100 (5 places), 50% transition density pattern (Figure 5), VCC = 3.3V, fCLK = 75MHz I(VCC) + I(PLLVCC) + I(LVDSVCC) 53.3 I(IOVCC) with IOVCC = 3.3V 0.6 I(IOVCC) with IOVCC = 1.8V 0.2 mA SHTDN = VIH, RL = 100 (5 places), worstcase pattern (Figure 6), VCC = 3.6V, fCLK = 75MHz ICC Supply current (average) I(VCC) + I(PLLVCC) + I(LVDSVCC) 63.7 I(IOVCC) with IOVCC = 3.3V 1.3 I(IOVCC) with IOVCC = 1.8V 0.5 mA SHTDN = VIH, RL = 100 (5 places), worstcase pattern (Figure 6), fCLK = 100MHz I(VCC) + I(PLLVCC) + I(LVDSVCC) 81.6 I(IOVCC) with IOVCC = 3.6V 1.6 I(IOVCC) with IOVCC = 1.8V 0.6 mA SHTDN = VIH, RL = 100 (5 places), worstcase pattern (Figure 6), fCLK = 135MHz CI (1) Input capacitance I(VCC) + I(PLLVCC) + I(LVDSVCC) 102.2 I(IOVCC) with IOVCC = 3.6V 2.1 I(IOVCC) with IOVCC = 1.8V 0.8 2 mA pF All typical values are at VCC = 3.3V, TA = 25C. Copyright (c) 2009-2011, Texas Instruments Incorporated 9 SN75LVDS83B SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 www.ti.com SWITCHING CHARACTERISTICS over operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP (1) MAX -0.1 0 0.1 ns UNIT t0 Delay time, CLKOUT after Yn valid (serial bit position 0, equal D1, D9, D20, D5) t1 Delay time, CLKOUT after Yn valid (serial bit position 1, equal D0, D8, D19, D27) 1 /7 tc - 0.1 1 /7 tc + 0.1 ns t2 Delay time, CLKOUT after Yn valid (serial bit position 2, equal D7, D18, D26. D23) 2 /7 tc - 0.1 2 /7 tc + 0.1 ns t3 Delay time, CLKOUT after Yn valid (serial bit position 3; equal D6, D15, D25, D17) 3 /7 tc - 0.1 3 /7 tc + 0.1 ns t4 Delay time, CLKOUT after Yn valid (serial bit position 4, equal D4, D14, D24, D16) 4 /7 tc - 0.1 4 /7 tc + 0.1 ns t5 Delay time, CLKOUT after Yn valid (serial bit position 5, equal D3, D13, D22, D11) 5 /7 tc - 0.1 5 /7 tc + 0.1 ns t6 Delay time, CLKOUT after Yn valid (serial bit position 6, equal D2, D12, D21, D10) 6 /7 tc - 0.1 6 /7 tc + 0.1 ns tc(o) Output clock period tc(o) Output clock cycle-to-cycle jitter See Figure 7, tC = 10ns, |Input clock jitter| < 25ps (2) tc (3) tC = 10ns; clean reference clock, see Figure 8 26 tC = 10ns with 0.05UI added noise modulated at 3MHz, see Figure 8 44 tC = 7.4ns; clean reference clock, see Figure 8 35 tC = 7.4ns with 0.05UI added noise modulated at 3MHz, see Figure 8 42 ns ps tw High-level output clock pulse duration tr/f Differential output voltage transition time (tr or tf) See Figure 4 ten Enable time, SHTDN to phase lock (Yn valid) f(clk) = 135MHz, See Figure 9 6 s tdis Disable time, SHTDN to off-state (CLKOUT high-impedance) f(clk) = 135MHz, See Figure 10 7 ns (1) (2) (3) 4 /7 tc 225 ns 500 ps All typical values are at VCC = 3.3 V, TA = 25C. |Input clock jitter| is the magnitude of the change in the input clock period. The output clock cycle-to-cycle jitter is the largest recorded change in the output clock period from one cycle to the next cycle observed over 15,000 cycles.Tektronix TDSJIT3 Jitter Analysis software was used to derive the maximum and minimum jitter value. THERMAL CHARACTERISTICS PARAMETER TEST CONDITIONS ZQL MIN TYP DGG MAX MIN TYP MAX UNIT Low-K JEDEC test board, 1s (single signal layer), no air flow 85 High-K JEDEC test board, 2s2p (double signal layer, double buried power plane), no air flow 67.1 63.4 Junction-to-case thermal resistance Cu cold plate measurement process 25.2 15.9 C/W JB Junction-to-board thermal resistance EIA/JESD 51-8 31.0 32.5 C/W JT Junction-to-top of package EIA/JESD 51-2 0.8 0.4 C/W JA Junction-to-free-air thermal resistance JC 10 C/W Copyright (c) 2009-2011, Texas Instruments Incorporated SN75LVDS83B www.ti.com SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 THERMAL CHARACTERISTICS (continued) PARAMETER ZQL TEST CONDITIONS JB Junction-to-board MIN EIA/JESD 51-6 TA Operating ambient temperature range TJ Virtual junction temperature TYP DGG MAX MIN 30.3 TYP MAX 32.2 UNIT C/W -10 70 -10 70 C 0 105 0 105 C PARAMETER MEASUREMENT INFORMATION tsu thold Dn CLKIN All input timing is defined at IOVDD / 2 on an input signal with a 10% to 90% rise or fall time of less than 3 ns. CLKSEL = 0V. Figure 3. Set Up and Hold Time Definition 49.9W 1% (2 PLCS) YP VOD VOC YM 100% 80% VOD(H) 0V VOD(L) 20% 0% tf tr VOC(PP) VOC(SS) VOC(SS) 0V Figure 4. Test Load and Voltage Definitions for LVDS Outputs. Copyright (c) 2009-2011, Texas Instruments Incorporated 11 SN75LVDS83B SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 www.ti.com PARAMETER MEASUREMENT INFORMATION (continued) CLKIN D0,8,16 D1,9,17 D2,10,18 D3,11,19 D4-7,12-15,20-23 D24-27 The 16 grayscale test pattern test device power consumption for a typical display pattern. Figure 5. 16 Grayscale Test Pattern T CLKIN EVEN Dn ODD Dn The worst-case test pattern produces nearly the maximum switching frequency for all of the LVDS outputs. Figure 6. Worst-Case Power Test Pattern t7 CLKIN CLKOUT t6 t5 t4 t3 t2 t0 Yn t1 ~2.5V 1.40V CLKIN VOD(H) CLKOUT or Yn 0.00V ~0.5V t7 VOD(L) t0-6 CLKOUT is shown with CLKSEL at high-level. CLKIN polarity depends on CLKSEL input level. Figure 7. SN75LVDS83B Timing Definitions 12 Copyright (c) 2009-2011, Texas Instruments Incorporated SN75LVDS83B www.ti.com SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 PARAMETER MEASUREMENT INFORMATION (continued) + Reference Device Under Test VCO + Modulation v(t) = A sin(2 pfmodt) HP8656B Signal Generator, 0.1 MHz-990 MHz RF Output HP8665A Synthesized Signal Generator, 0.1 MHz-4200 MHz Device Under Test RF Output Modulation Input CLKIN CLKOUT DTS2070C Digital TimeScope Input Figure 8. Output Clock Jitter Test Set Up CLKIN Dn ten SHTDN Invalid Yn Valid Figure 9. Enable Time Waveforms CLKIN tdis SHTDN CLKOUT Figure 10. Disable Time Waveforms Copyright (c) 2009-2011, Texas Instruments Incorporated 13 SN75LVDS83B SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 www.ti.com TYPICAL CHARACTERISTICS AVERAGE GRAYSCALE ICC vs CLOCK FREQUENCY 100 OUTPUT CLOCK JITTER vs INPUT CLOCK JITTER 800 Total Device Current (Using Grayscale pattern) Over Pixel Clock Frequency Output Jitter 700 80 Period Clock Jitter - ps-pp ICC - Average Supply Current - mA 90 VCC = 3.6V 70 60 50 VCC = 3.3V 40 600 Input Jitter 500 400 300 200 VCC = 3V CLK Frequency During Test = 100MHz 30 100 20 10 30 50 70 90 110 130 0 0.01 fclk - Clock Frequency - MHz 0.10 1 10 f(mod) - Input Modular Frequency - MHz Figure 11. Figure 12. TYPICAL PRBS OUTPUT SIGNAL OVER ONE CLOCK PERIOD PRBS Data Signal V - Voltage - 80mV/div CLKL Signal Clock Signal: 135MHz tk - Time - 1ns/div Figure 13. 14 Copyright (c) 2009-2011, Texas Instruments Incorporated SN75LVDS83B www.ti.com SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 APPLICATION INFORMATION This section describes the power up sequence, provides information on device connectivity to various GPU and LCD display panels, and offers a pcb routing example. Power Up Sequence The SN75LVDS83B does not require a specific power up sequence. It is permitted to power up IOVCC while VCC, VCCPLL, and VCCLVDS remain powered down and connected to GND. The input level of the SHTDN during this time does not matter as only the input stage is powered up while all other device blocks are still powered down. It is also permitted to power up all 3.3V power domains while IOVCC is still powered down to GND. The device will not suffer damage. However, in this case, all the I/Os are detected as logic HIGH, regardless of their true input voltage level. Hence, connecting SHTDN to GND will still be interpreted as a logic HIGH; the LVDS output stage will turn on. The power consumption in this condition is significantly higher than standby mode, but still lower than normal mode. The user experience can be impacted by the way a system powers up and powers down an LCD screen. The following sequence is recommended: Power up sequence (SN75LVDS83B SHTDN input initially low): 1. Ramp up LCD power (maybe 0.5ms to 10ms) but keep backlight turned off. 2. Wait for additional 0-200ms to ensure display noise won't occur. 3. Enable video source output; start sending black video data. 4. Toggle LVDS83B shutdown to SHTDN = VIH. 5. Send >1ms of black video data; this allows the LVDS83B to be phase locked, and the display to show black data first. 6. Start sending true image data. 7. Enable backlight. Power Down sequence (SN75LVDS83B SHTDN input initially high): 1. Disable LCD backlight; wait for the minimum time specified in the LCD data sheet for the backlight to go low. 2. Video source output data switch from active video data to black image data (all visible pixel turn black); drive this for >2 frame times. 3. Set SN75LVDS83B input SHTDN = GND; wait for 250ns. 4. Disable the video output of the video source. 5. Remove power from the LCD panel for lowest system power. Signal Connectivity While there is no formal industry standardized specification for the input interface of LVDS LCD panels, the industry has aligned over the years on a certain data format (bit order). Figure 14 through Figure 17 show how each signal should be connected from the graphic source through the SN75LVDS83B input, output and LVDS LCD panel input. Detailed notes are provided with each figure. Copyright (c) 2009-2011, Texas Instruments Incorporated 15 SN75LVDS83B SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 www.ti.com SN75LVDS83B 4.8k 1.8V or 2.5V or 3.3V C1 Rpullup Rpulldown Y0M Y0P Y2M Y2P Y3M Y3P 100 to column driver 100 FPC Cable Panel connector Y1M Y1P LVDS timing Controller (8bpc, 24bpp) 100 100 to row driver CLKOUTM CLKOUTP 100 VCC PLLVCC LVDSVCC 24-bpp LCD Display GND SHTDN D27 D5 D0 D1 D2 D3 D4 D6 D10 D11 D7 D8 D9 D12 D13 D14 D16 D17 D15 D18 D19 D20 D21 D22 D24 D25 D26 D23 CLKIN CLKSEL FORMAT2 (See Note A) D0 D1 D2 D3 D4 D6 D27 D5 D7 D8 D9 D12 D13 D14 D10 D11 D15 D18 D19 D20 D21 D22 D16 D17 D24 D25 D26 D23 CLKIN IOVCC VDDGPUIO GND R0(LSB) R1 R2 R3 R4 R5 R6 R7(MSB) G0(LSB) G1 G2 G3 G4 G5 G6 G7(MSB) B0(LSB) B1 B2 B3 B4 B5 B6 B7(MSB) HSYNC VSYNC ENABLE RSVD (Note C) CLK FORMAT1 Main board connector 24-bpc GPU 3.3V C2 3.3V C3 (See Note B) Main Board Note A. FORMAT: The majority of 24-bit LCD display panels require the two most significant bits (2 MSB ) of each color to be transferred over the 4th serial data output Y3. A few 24-bit LCD display panels require the two LSBs of each color to be transmitted over the Y3 output. The system designer needs to verify which format is expected by checking the LCD display data sheet. * Format 1: use with displays expecting the 2 MSB to be transmitted over the 4th data channel Y3. This is the dominate data format for LCD panels. * Format 2: use with displays expecting the 2 LSB to be transmitted over the 4th data channel. Note B. Rpullup: install only to use rising edge triggered clocking. Rpulldown: install only to use falling edge triggered clocking. * C1: decoupling cap for the VDDIO supply; install at least 1x0.01F. * C2: decoupling cap for the VDD supply; install at least 1x0.1F and 1x0.01F. * C3: decoupling cap for the VDDPLL and VDDLVDS supply; install at least 1x0.1F and 1x0.01F. Note C. If RSVD is not driven to a valid logic level, then an external connection to GND is recommended. Note D. RSVD must be driven to a valid logic level. All unused SN75LVDS83B inputs must be tied to a valid logic level. Figure 14. 24-Bit Color Host to 24-bit LCD Panel Application 16 Copyright (c) 2009-2011, Texas Instruments Incorporated SN75LVDS83B www.ti.com SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 SN75LVDS83B B0(LSB) B1 B2 B3 B4 B5(MSB) C1 100 FPC Cable Panel connector to column driver CLKOUTM CLKOUTP LVDS timing Controller (6-bpc, 18-bpp) 100 100 to row driver 18-bpp LCD Display Y3M Y3P 4.8k 1.8V or 2.5V or 3.3V Y1M Y1P Y2M Y2P IOVCC VDDGPUIO GND HSYNC VSYNC ENABLE RSVD CLK 100 Rpullup (See Note A) VCC PLLVCC LVDSVCC G0(LSB) G1 G2 G3 G4 G5(MSB) Y0M Y0P Main board connector D0 D1 D2 D3 D4 D6 D27 D5 D7 D8 D9 D12 D13 D14 D10 D11 D15 D18 D19 D20 D21 D22 D16 D17 D24 D25 D26 D23 CLKIN GND R0(LSB) R1 R2 R3 R4 R5(MSB) SHTDN CLKSEL 18-bpp GPU 3.3V C2 3.3V C3 Rpulldown (See Note B) Main Board Note A. Leave output Y3 NC. Note B.Rpullup: install only to use rising edge triggered clocking. Rpulldown: install only to use falling edge triggered clocking. * C1: decoupling cap for the VDDIO supply; install at least 1x0.01F. * C2: decoupling cap for the VDD supply; install at least 1x0.1F and 1x0.01F. * C3: decoupling cap for the VDDPLL and VDDLVDS supply; install at least 1x0.1F and 1x0.01F. Figure 15. 18-Bit Color Host to 18-Bit Color LCD Panel Display Application Copyright (c) 2009-2011, Texas Instruments Incorporated 17 SN75LVDS83B SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 12-bpp GPU www.ti.com SN75LVDS83B (See Note B) D0 D1 D2 D3 D4 D6 D27 D5 D7 D8 D9 D12 D13 D14 D10 D11 D15 D18 D19 D20 D21 D22 D16 D17 D24 D25 D26 D23 CLKIN (See Note B) B2 or VCC B3 or GND B0 B1 B2 B3(MSB) C1 FPC Cable t Panell connector Main board connector CLKOUTM CLKOUTP LVDS timing Controller (6-bpc, 18-bpp) 100 100 to row driver 18-bpp LCD Display Y3M Y3P 4.8k 1.8V or 2.5V or 3.3V 100 Y2M Y2P IOVCC VDDGPUIO GND HSYNC VSYNC ENABLE RSVD CLK to column driver Rpullup (See Note A) VCC PLLVCC LVDSVCC G2 or VCC G3 or GND G0 G1 G2 G3(MSB) 100 Y1M Y1P SHTDN CLKSEL (See Note B) Y0M Y0P GND R2 or VCC R3 or GND R0 R1 R2 R3(MSB) 3.3V C2 3.3V C3 Rpulldown (See Note C) Main Board Note A. Leave output Y3 N.C. Note B. R3, G3, B3: this MSB of each color also connects to the 5th bit of each color for increased dynamic range of the entire color space at the expense of none-linear step sizes between each step. For linear steps with less dynamic range, connect D1, D8, and D18 to GND. R2, G2, B2: these outputs also connects to the LSB of each color for increased, dynamic range of the entire color space at the expense of none-linear step sizes between each step. For linear steps with less dynamic range, connect D0, D7, and D15 to VCC. Note C.Rpullup: install only to use rising edge triggered clocking. Rpulldown: install only to use falling edge triggered clocking. * C1: decoupling cap for the VDDIO supply; install at least 1x0.01F. * C2: decoupling cap for the VDD supply; install at least 1x0.1F and 1x0.01F. * C3: decoupling cap for the VDDPLL and VDDLVDS supply; install at least 1x0.1F and 1x0.01F. Figure 16. 12-Bit Color Host to 18-Bit Color LCD Panel Display Application 18 Copyright (c) 2009-2011, Texas Instruments Incorporated SN75LVDS83B www.ti.com SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 SN75LVDS83B D0 D1 D2 D3 D4 D6 D27 D5 D7 D8 D9 D12 D13 D14 D10 D11 D15 D18 D19 D20 D21 D22 D16 D17 D24 D25 D26 D23 CLKIN G7(MSB) B0 and B1: NC (See Note B) B2 B3 B4 B5 B6 B7(MSB) B0 and B1: NC (See Note B) CLKOUTM CLKOUTP C1 FPC Cable LVDS timing Controller (6-bpc, 18-bpp) 100 100 to row driver 18-bpp LCD Display Y3M Y3P 4.8k 1.8V or 2.5V or 3.3V 100 Y2M Y2P IOVCC VDDGPUIO GND HSYNC VSYNC ENABLE RSVD CLK to column driver Y1M Y1P t Panell connector G2 G3 G4 G5 G6 100 Main board connector G0 and G1: NC (See Note B) Y0M Y0P SHTDN CLKSEL R7(MSB) Rpullup (See Note A) VCC PLLVCC LVDSVCC R2 R3 R4 R5 R6 GND 24-bpp GPU R0 and R1: NC (See Note B) 3.3V C2 3.3V C3 Rpulldown (See Note C) Main Board Note A. Leave output Y3 NC. Note B. R0, R1, G0, G1, B0, B1: For improved image quality, the GPU should dither the 24-bit output pixel down to18-bit per pixel. NoteC.Rpullup: install only to use rising edge triggered clocking. Rpulldown: install only to use falling edge triggered clocking. * C1: decoupling cap for the VDDIO supply; install at least 1x0.01F. * C2: decoupling cap for the VDD supply; install at least 1x0.1F and 1x0.01F. * C3: decoupling cap for the VDDPLL and VDDLVDS supply; install at least 1x0.1F and 1x0.01F. Figure 17. 24-Bit Color Host to 18-Bit Color LCD Panel Display Application Copyright (c) 2009-2011, Texas Instruments Incorporated 19 SN75LVDS83B SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 www.ti.com Typical Application Schematic Figure 18 represents the schematic drawing of the SN75LVDS83B evaluation module. J1 U1H GND1 GND2 GND3 GND4 GND5 GND6 GND7 PLLGND LVDSGND1 LVDSGND2 J3 CLKM CLKP Y0P Y0M Y1P Y1M Y2P Y2M IOVCC R4 4.7k R5 4.7k R6 4.7k R7 4.7k R8 4.7k R9 4.7k Y3P Y3M R10 4.7k JMP1 U1B J2 K1 K2 J3 K3 J4 K5 D0 D1 D2 D3 D4 D6 D7 D1 D2 G2 G1 J5 E1 E2 sma_surface J6 sma_surface C2 C1 J7 sma_surface SN65LVDS83BZQL J8 sma_surface J9 sma_surface 14 Header 7x2 J10 sma_surface IOVCC R11 4.7k R12 4.7k R13 4.7k R14 4.7k R15 4.7k R16 4.7k R17 4.7k sma_surface JMP2 U1C K6 J6 G5 G6 F6 E5 D5 J4 sma_surface H2 H1 1 2 SN65LVDS83BZQL D8 D9 D12 D13 D14 D15 D18 sma_surface U1A SN65LVDS83BZQL D0 D1 D2 D3 D4 D6 D7 J2 sma_surface C3 C5 D3 F5 G3 H3 J5 A1 B1 F2 D8 D9 D12 D13 D14 D15 D18 1 2 IOVCC IOVCC 14 SN65LVDS83BZQL R2 R1 4.7k Header 7x2 IOVCC R18 4.7k R19 4.7k R20 4.7k R21 4.7k R22 4.7k R23 4.7k R24 4.7k JMP6 U1G JMP3 U1D D19 D20 D21 D22 D24 D25 D 26 C6 B6 B5 A6 A4 B4 A3 D19 D20 D21 D22 D24 D25 D26 SHTDN CLKSEL 1 2 B3 D4 SHTDN CLKSEL 1 2 3 4 Header 2x2 SN65LVDS83BZQL 14 U1J IOVCC R25 4.7k R26 4.7k R27 4.7k R28 4.7k R29 4.7k R30 4.7k E3 E4 F3 F4 NC1 NC2 NC3 NC4 Header 7x2 SN65LVDS83BZQL SN65LVDS83BZQL R31 4.7k JMP4 U1E D5 D10 D11 D16 D17 D23 D27 K4 H4 H6 E6 D6 A5 J1 D5 D10 D11 D16 D17 D23 D27 VCC 1 2 IOVCC U1I VCC PLLVCC LVDSVCC 14 IOVCC1 IOVCC2 Header 7x2 SN65LVDS83BZQL G4 B2 F1 H5 C4 SN65LVDS83BZQL VCC VCC C31 1uF C32 0.1uF C33 0.01uF VCC C34 1uF C35 0.1uF C36 0.01uF IOVCC C40 1uF C41 0.1uF C42 0.01uF C37 1uF C38 0.1uF C39 0.01uF PLACE UNDER LVDS83B (bottom pcb side) Figure 18. Schematic Example (SN75LVDS83B Evaluation Board) 20 Copyright (c) 2009-2011, Texas Instruments Incorporated SN75LVDS83B www.ti.com SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 PCB Routing Figure 19 and Figure 20 show a possible breakout of the data input and output signals from the BGA package. R1 R2 R3 R4 R5 R6 R7 R8 G0 G1 D8 D7 D5 D4 D2 D1 D9 GND D6 D3 D0 D27 D11 VCC D10 GND Y0P Y0M D13 D12 IOVCC GND Y1P Y1M D14 GND D16 D15 D17 D18 CLKSEL D19 GND IOVCC D20 D21 D25 D22 D23 D24 G2 G3 G4 G5 G6 G7 B0 B1 LVDS GND LVDS VCC Y2P Y2M GND CLKP CLKM GND Y3P Y3M B2 B3 B4 B5 B6 SHTDN PLLVCC LVDS GND +PLL GND D26 CLKIN PLL GND B7 HS VS EN CLK Figure 19. 24-Bit Color Routing (See Figure 14 for the Schematic) Copyright (c) 2009-2011, Texas Instruments Incorporated 21 SN75LVDS83B SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 www.ti.com G1 G0 D8 D7 R5 R4 R3 R2 D5 D4 D2 R1 R0 D1 To GND G2 G3 D9 GND D6 D3 D0 D27 D11 VCC D10 GND Y0P Y0M D13 D12 IOVCC GND Y1P Y1M D14 GND D16 D15 D17 D18 CLKSEL D19 GND IOVCC G4 G5 B0 LVDS GND LVDS VCC To GND B1 Y2P Y2M GND CLKP CLKM GND Y3P Y3M B2 remains unconnected B3 B4 D20 D21 D22 D23 D25 SHTDN PLLVCC LVDS GND +PLL GND CLKIN B5 D24 PLL GND D26 HS VS EN CLK Figure 20. 18-Bit Color Routing (See Figure 15, Figure 16, and Figure 17 for the Schematic) 22 Copyright (c) 2009-2011, Texas Instruments Incorporated SN75LVDS83B www.ti.com SLLS846B - MAY 2009 - REVISED SEPTEMBER 2011 REVISION HISTORY Changes from Original (May 2009) to Revision A Page * Changed text and replaced TBDs in Note A and Note B of Figure 14 ............................................................................... 16 * Changed Note B of Figure 15 - Replaced TBDs. ............................................................................................................... 17 * Changed Note B of Figure 16 - Replaced TBDs. ............................................................................................................... 18 * Changed Note C of Figure 17 - Replaced TBDs. ............................................................................................................... 19 * Changed Figure 19 - removed 3 GND pin locations. ......................................................................................................... 21 * Changed Figure 20 - removed 3 GND pin locations. ......................................................................................................... 22 Changes from Revision A (October 2009) to Revision B Page * Added Storage temperature, Ts to ABSOLUTE MAXIMUM RATINGS ................................................................................ 2 * Added Note 3 to DISSIPATION RATINGS ........................................................................................................................... 3 * Deleted max values for Supply current (average) ................................................................................................................ 9 * Changed Enable time units from ns to s .......................................................................................................................... 10 * Added Thermal Characteristics table .................................................................................................................................. 10 * Changed G7(LSB) to G7(MSB) in Figure 14 ...................................................................................................................... 16 * Added Note C to Figure 14 ................................................................................................................................................. 16 * Added Note D to Figure 14 ................................................................................................................................................. 16 * Added connection between GND and D23 to Figure 19 .................................................................................................... 21 Copyright (c) 2009-2011, Texas Instruments Incorporated 23 PACKAGE OPTION ADDENDUM www.ti.com 26-Mar-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) (Requires Login) SN75LVDS83BDGG ACTIVE TSSOP DGG 56 35 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN75LVDS83BDGGR ACTIVE TSSOP DGG 56 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN75LVDS83BZQLR ACTIVE BGA MICROSTAR JUNIOR ZQL 56 1000 Green (RoHS & no Sb/Br) SNAGCU Samples Level-2-260C-1 YEAR (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SN75LVDS83BDGGR TSSOP DGG 56 2000 330.0 24.4 8.6 15.6 1.8 12.0 24.0 Q1 SN75LVDS83BZQLR BGA MI CROSTA R JUNI OR ZQL 56 1000 330.0 16.4 4.8 7.3 1.5 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN75LVDS83BDGGR TSSOP DGG 56 2000 367.0 367.0 45.0 SN75LVDS83BZQLR BGA MICROSTAR JUNIOR ZQL 56 1000 336.6 336.6 28.6 Pack Materials-Page 2 MECHANICAL DATA MTSS003D - JANUARY 1995 - REVISED JANUARY 1998 DGG (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 48 PINS SHOWN 0,27 0,17 0,50 48 0,08 M 25 6,20 6,00 8,30 7,90 0,15 NOM Gage Plane 1 0,25 24 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 48 56 64 A MAX 12,60 14,10 17,10 A MIN 12,40 13,90 16,90 DIM 4040078 / F 12/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated