SPEC NO: DSAI9664 REV NO: V.5A DATE: MAR/30/2013 PAGE: 1 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101024772
T-1 3/4 (5mm) SOLID STATE LAMP
Part Number: WP7113SEC/J3 Hyper Red
Features
zLow power consumption.
zPopular T-1 3/4 diameter package.
zGeneral purpose leads.
zReliable and rugged.
zLong life - solid state reliability.
zAvailable on tape and reel.
zRoHS compliant.
Description
The Hyper Red device is based on light emitting diode chip
made from AlGaInP.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
SPEC NO: DSAI9664 REV NO: V.5A DATE: MAR/30/2013 PAGE: 2 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101024772
Selection Guide
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
* Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Absolute Maximum Ratings at TA=25°C
Electrical / Optical Characteristics at TA=25°C
Notes:
1.Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
Notes:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
2. 2mm below package base.
3. 5mm below package base.
Part No. Dice Lens Type
Iv (mcd) [2]
@ 20mA
V
iewing
Angle [1]
Min. Typ. 2θ1/2
WP7113SEC/J3 Hyper Red (AlGaInP) Water Clear
7000 11000
*5000 *8000
20°
Symbol Parameter Device Typ. Max. Units Test Conditions
λpeak Peak Wavelength Hyper Red 640 nm IF=20mA
λD [1] Dominant Wavelength Hyper Red 625 nm IF=20mA
Δλ1/2 Spectral Line Half-width Hyper Red 25 nm IF=20mA
C Capacitance Hyper Red 27 pF VF=0V;f=1MHz
VF [2] Forward Voltage Hyper Red 2.2 2.8 V IF=20mA
IR Reverse Current Hyper Red 10 uA VR = 5V
Parameter Hyper Red Units
Power dissipation 84 mW
DC Forward Current 30 mA
Peak Forward Current [1] 150 mA
Reverse Voltage 5 V
Operating/Storage Temperature -40°C To +85°C
Lead Solder Temperature [2] 260°C For 3 Seconds
Lead Solder Temperature [3] 260°C For 5 Seconds
SPEC NO: DSAI9664 REV NO: V.5A DATE: MAR/30/2013 PAGE: 3 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101024772
Hyper Red WP7113SEC/J3
SPEC NO: DSAI9664 REV NO: V.5A DATE: MAR/30/2013 PAGE: 4 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101024772
PACKING & LABEL SPECIFICATIONS WP7113SEC/J3
SPEC NO: DSAI9664 REV NO: V.5A DATE: MAR/30/2013 PAGE: 5 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101024772
SPEC NO: DSAI9664 REV NO: V.5A DATE: MAR/30/2013 PAGE: 6 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101024772
All design applications should refer to Kingbright application notes available at
http://www.KingbrightUSA.com/ApplicationNotes