ALUMINUM ELECTROLYTIC CAPACITORS CW Chip Type, Low Impedance, Long Life Assurance series Chip type with load life of 7000 hours at +105C. Low impedance temperature range up to +105C. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2002/95/EC). CW Low Impedance CB Specifications Item Performance Characteristics Category Temperature Range - 25 to +105C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 10 to 470F Capacitance Tolerance 20% at 120Hz, 20C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (A) , whichever is greater. Measurement frequency : 120Hz, Temperature : 20C Tangent of loss angle (tan ) Rated voltage (V) tan (MAX.) 6.3 0.32 10 0.28 16 0.26 25 0.16 35 0.14 50 0.14 Measurement frequency : 120Hz Rated voltage (V) Stability at Low Temperature Impedance ratio ZT / Z20 (MAX.) 6.3 10 16 25 35 50 4 3 2 2 2 2 Z- 25C / Z+20C The specifications listed at right shall be met when the capacitors are restored to 20C after the rated voltage is applied for 7000 hours at 105C. Endurance Capacitance change tan Leakage current Within 30% of the initial capacitance value 300% or less than the initial specified value Less than or equal to the initial specified value After storing the capacitors under no load at 105C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within 10% of the initial capacitance value maintained at 250C. The capacitors shall meet the Less than or equal to the initial specified value tan characteristic requirements listed at right when they are Less than or equal to the initial specified value Leakage current removed from the plate and restored to 20C. Shelf Life Resistance to soldering heat Black print on the case top. Marking Type numbering system (Example : 10V 150F) Chip Type (5 to 6.3 ) 2 3 4 5 6 7 8 9 10 11 12 13 14 Taping code E B 0.2 D 0.5 A2 150C CW L 0.3 Capacitance Lot No. 1 U CW 1 A 1 5 1 MC L 1 G S A 0.2 A 0.2 C 0.2 0.3MAX. Series 0.5MAX. Positive Plastic platform Voltage ( C : 16V ) Configuration Capacitance tolerance (20%) Rated capacitance (150F) Rated voltage (10V) Negative H D 5 * 6.3 8 * 10 Code CL NL Series name Type (8 to 10 ) Positive L 0.5 Lot No. Voltage V 6.3 Code j Capacitance 10 A 16 C Negative Pressure relief vent 25 E 35 V (mm) D A 0.2 A 0.2 B 0.2 A2 220V CW D 0.5 Series Trade mark C 0.2 0.3MAX. E Voltage ( V : 35V ) 0.5MAX. Plastic platform H xL 10 x 10 5x7 6.3 x 7 6.3 x 8.7 8 x 10 A 2.1 2.4 2.4 2.9 3.2 B 5.3 6.6 6.6 8.3 10.3 C 5.3 6.6 6.6 8.3 10.3 E 1.3 2.2 2.2 3.1 4.5 L 7.0 7.0 8.7 10 10 H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 50 H Dimension table in next page. CAT.8100Y ALUMINUM ELECTROLYTIC CAPACITORS CW series Dimensions Cap. (F) V 6.3 10 16 25 35 50 Code 0J 1A 1C 1E 1V 1H 10 100 22 220 33 330 5x7 5x7 2.2 2.2 95 95 5x7 2.2 5x7 2.2 95 5x7 2.2 95 6.3 x 7 1.1 140 6.3 x 8.7 1.0 230 6.3 x 8.7 1.0 230 95 47 470 5x7 2.2 95 6.3 x 7 1.1 140 6.3 x 7 1.1 140 100 101 6.3 x 7 1.1 140 6.3 x 7 1.1 140 6.3 x 8.7 1.0 230 150 151 6.3 x 8.7 1.0 230 220 221 6.3 x 8.7 1.0 230 6.3 x 8.7 1.0 230 8 x 10 0.22 600 8 x 10 0.22 600 330 331 6.3 x 8.7 1.0 230 8 x 10 0.22 600 8 x 10 0.22 600 10 x 10 0.16 850 470 471 8 x 10 0.22 600 8 x 10 0.22 600 10 x 10 0.16 850 6.3 x 7 1.1 140 8 x 10 0.53 350 8 x 10 0.53 350 10 x 10 0.35 670 Impedance Rated ripple Case size D x L (mm) Max. impedance () at 20C 100kHz, Rated ripple current (mArms) at 105C 100kHz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.35 120 Hz 0.50 300 Hz 0.64 1 kHz 0.83 10 kHz or more 1.00 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100Y