TPS62110, TPS62111 TPS62112, TPS62113 www.ti.com .................................................................................................................................................... SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 17-V, 1.5-A, SYNCHRONOUS STEP-DOWN CONVERTER FEATURES DESCRIPTION 1 * * * * * * * * * * * High-Efficiency Synchronous Step-Down Converter With up to 95% Efficiency 3.1-V to 17-V Operating Input Voltage Range Adjustable Output Voltage Range From 1.2 V to 16 V Fixed Output Voltage Options Available in 3.3 V and 5 V Synchronizable to External Clock Signal up to 1.4 MHz Up to 1.5-A Output Current High Efficiency Over a Wide Load-Current Range Due to PFM/PWM Operation Mode 100% Maximum Duty Cycle for Lowest Dropout 20-A Quiescent Current (Typical) Overtemperature and Overcurrent Protected Available in 16-Pin QFN Package The TPS6211x devices are a family of low-noise synchronous step-down dc-dc converters that are ideally suited for systems powered from a 2-cell Li-ion battery or from a 12-V or 15-V rail. The TPS6211x is a synchronous PWM converter with integrated N- and P-channel power MOSFET switches. Synchronous rectification is used to increase efficiency and to reduce external component count. To achieve highest efficiency over a wide load-current range, the converter enters a power-saving, pulse-frequency modulation (PFM) mode at light load currents. Operating frequency is typically 1 MHz, allowing the use of small inductor and capacitor values. The device can be synchronized to an external clock signal in the range of 0.8 MHz to 1.4 MHz. For low-noise operation, the converter can be operated in PWM-only mode. In the shutdown mode, the current consumption is reduced to less than 2 A. The TPS6211x is available in the 16-pin (RSA) QFN package, and operates over a free-air temperature range of -40C to 85C. APPLICATIONS * * * TPS62111 Efficiency vs Output Current Point-of-Load Regulation From 12-V Bus Organizers, PDAs, and Handheld PCs Handheld Scanners 100 4.2 V 90 TYPICAL APPLICATION VI = 3.8 V to 17 V TPS62111 VIN VIN EN SW SW VINA PG VO = 3.3 V 1 MW 1 mF LBO AGND LBI FB CO = 22 mF 6.3 V Efficiency - % CI = 10 mF 25 V 80 6.8 mH 5V 70 60 8.4 V 50 12 V 40 SYNC GND GND PwPD PGND PGND 30 VO = 3.3 V TA = 25oC PFM Mode 20 10 0 0.0001 0.001 0.01 0.1 1 10 IO - Output Current- A 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2005-2009, Texas Instruments Incorporated TPS62110, TPS62111 TPS62112, TPS62113 SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 .................................................................................................................................................... www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION PLASTIC QFN 16 PIN (RSA) (1) (1) OUTPUT VOLTAGE LBI/LBO FUNCTIONALITY MARKING TPS62110 Adjustable 1.2 V to 16 V Standard TPS62110 TPS62111 3.3 V Standard TPS62111 TPS62112 5V Standard TPS62112 TPS62113 Adjustable 1.2 V to 16 V Enhanced TPS62113 The RSA package is available in tape and reel. Add R suffix (TPS62110RSAR) to order quantities of 3000 parts per reel. Add T suffix (TPS62110RSAT) to order quantities of 250 parts per reel. ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range (unless otherwise noted) VALUE VCC Supply voltage at VIN, VINA -0.3 V to 20 V Voltage at SW VI -1 V to 20 V Voltage at EN, SYNC, LBO, PG -0.3 V to 20 V Voltage at LBI, FB -0.3 V to 7 V IO Output current at SW TJ Maximum junction temperature TA Operating free-air temperature -40C to 85C Tstg Storage temperature -65C to 150C (1) 2400 mA 150C Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. DISSIPATION RATINGS (1) (1) PACKAGE TA 25C POWER RATING DERATING FACTOR ABOVE TA = 25C TA = 70C POWER RATING TA = 85C POWER RATING RSA 2.5 W 25 mW/C 1.375 W 1W Based on a thermal resistance of 40 K/W soldered onto a high-K board. RECOMMENDED OPERATING CONDITIONS MIN VCC Supply voltage at VIN, VINA 3.1 Maximum voltage at power-good, LBO, EN, SYNC TJ 2 Operating junction temperature Submit Documentation Feedback -40 NOM MAX UNIT 17 V 17 V 125 C Copyright (c) 2005-2009, Texas Instruments Incorporated Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 TPS62110, TPS62111 TPS62112, TPS62113 www.ti.com .................................................................................................................................................... SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 ELECTRICAL CHARACTERISTICS VI = 12 V, VO = 3.3 V, IO = 600 mA, EN = VI, TA = -40C to 85C (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT SUPPLY CURRENT VI Input voltage range 3.1 I(Q) Operating quiescent current IO = 0 mA, SYNC = GND, VI = 7.2 V, TA = 25C (1) IO = 0 mA, SYNC = GND, VI = 17 V IQ(LBI) Quiescent current with enhanced LBI comparator version (TPS62113 only). I(SD) Shutdown current 17 V 20 A (1) 23 26 EN = VI , LBI = GND 10 A EN = GND 1.5 5 EN = GND, TA = 25C, VI = 7.2 V 1.5 3 A ENABLE VIH EN high-level input voltage VIL EN low-level input voltage 1.3 V 0.3 EN trip-point hysteresis 170 Ilkg EN input leakage current EN = GND or VI, VI = 12 V I(EN) EN input current 0.6 V V(EN) 4 V V(UVLO) Undervoltage lockout threshold Input voltage falling 2.8 V mV 0.01 0.2 A 10 20 A 3 3.1 V 250 300 mV VI 5.4 V; IO = 350 mA 165 250 VI = 3.5 V; IO = 200 mA 340 VI = 3 V; IO = 100 mA 490 P-channel MOSFET leakage current VDS = 17 V 0.1 1 A P-channel MOSFET current limit VI = 7.2 V, VO = 3.3 V mA Undervoltage lockout hysteresis POWER SWITCH rDS(ON) rDS(ON) P-channel MOSFET on-resistance N-channel MOSFET on-resistance N-channel MOSFET leakage current 2100 m 2400 2600 VI 5.4 V; IO = 350 mA 145 200 VI = 3.5 V; IO = 200 mA 170 VI = 3 V; IO = 100 mA 200 VDS = 17 V 0.1 m 2 A POWER-GOOD OUTPUT, LBI, LBO V(PG) Power-good trip voltage VO - 1.6% Power-good delay time VOL PG, LBO output-low voltage IOL PG, LBO sink current VO ramping positive 50 VO ramping negative 200 V(FB) = 0.8 x VO nominal, IOL = 1 mA s 0.3 1 PG, LBO output leakage current V(FB) = VO nominal, V(LBI) = VI 0.01 Minimum supply voltage for valid power good, LBI, LBO signal VLBI Low-battery input trip voltage ILBI LBI input leakage current Input voltage falling V mA 0.25 A 3 V 1.256 V 10 Low-battery input trip-point accuracy 100 nA 1.5% VLBI,HYS Low-battery input hysteresis (1) V 25 mV Device is not switching. Copyright (c) 2005-2009, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 3 TPS62110, TPS62111 TPS62112, TPS62113 SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 .................................................................................................................................................... www.ti.com ELECTRICAL CHARACTERISTICS (continued) VI = 12 V, VO = 3.3 V, IO = 600 mA, EN = VI, TA = -40C to 85C (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 900 1000 1100 kHz 1400 kHz OSCILLATOR fS Oscillator frequency f(SYNC) Synchronization range VIH SYNC high-level input voltage VIL SYNC low-level input voltage Ilkg SYNC input leakage current CMOS-logic clock signal on SYNC pin 800 1.5 SYNC = GND or VIN 0.01 SYNC trip-point hysteresis 0.2 170 0.6 V V(SYNC) 4 V SYNC input current V 0.3 Duty cycle of external clock signal 10 30% V A mV 20 A 90% OUTPUT VO Adjustable output voltage range TPS62110 VFB Feedback voltage TPS62110 1.153 FB leakage current TPS62110 10 Feedback voltage tolerance VI = 3.1 V to 17 V; TPS62110 0 mA < IO < 1500 mA (2) -2% 2% TPS62111 VI = 3.8 V to 17 V; 0 mA < IO < 1500 mA (2) -3% 3% TPS62112 VI = 5.5 V to 17 V; 0 mA < IO < 1500 mA (2) -3% 3% Fixed output-voltage tolerance (3) IO Maximum output current 1.153 VI 3 V (once undervoltage lockout voltage exceeded) 100 VI 3.5 V 500 VI 4.3 V 1200 VI 6 V 1500 Current into internal voltage divider for fixed voltage versions at 1 MHz Minimum ton time for main switch 10% (2) (3) 4 nA mA A 100% 100 Shutdown temperature Start-up time 100 92% VI = 12 V, Vo = 5 V, Io = 600 mA Duty-cycle range for main switches V V 5 VI = 7.2 V; VO = 3.3 V; IO = 600 mA Efficiency 16 IO = 800 mA, VI = 12 V, Vo = 3.3 V ns 145 C 1 ms The maximum output current depends on the input voltage. See the maximum output current for further restrictions on the minimum input voltage. The output voltage accuracy includes line and load regulation over the full temperature range TA = -40C to 85C. See the No-Load Operation section in this data sheet. Submit Documentation Feedback Copyright (c) 2005-2009, Texas Instruments Incorporated Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 TPS62110, TPS62111 TPS62112, TPS62113 www.ti.com .................................................................................................................................................... SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 DEVICE INFORMATION PGND SW SW PG PIN ASSIGNMENT TOP VIEW 2 3 4 16 15 14 13 12 Exposed Thermal Pad 11 10 5 6 7 8 9 GND GND FB AGND VINA 1 SYNC LBO LBI PGND VIN VIN EN TERMINAL FUNCTIONS TERMINAL NAME NO. I/O DESCRIPTION AGND 9 I Analog ground, connect to GND and PGND EN 4 I Enable. A logic high enables the converter; logic low forces the device into shutdown mode reducing the supply current to less than 2 A. FB 10 I Feedback pin for the fixed output voltage option. For the adjustable version, an external resistive divider is connected to this pin. The internal voltage divider is disabled for the adjustable version. GND 11, 12 I Ground LBI 7 I Low-battery input LBO 6 O Open-drain, low-battery output. This pin is pulled low if LBI is below its threshold. PG 13 O Power good comparator output. This is an open-drain output. A pullup resistor should be connected between PG and VOUT. The output goes active high when the output voltage is greater than 98.4% of the nominal value. PGND 1, 16 I Power ground. Connect all power grounds to this pin. SW 14, 15 O Connect the inductor to this pin. This pin is the switch pin and connected to the drain of the internal power MOSFETS. Input for synchronization to external clock signal. Synchronizes the converter switching frequency to an external clock signal with CMOS level: SYNC 5 I SYNC = HIGH: Low-noise mode enabled, fixed frequency PWM operation is forced SYNC = LOW (GND): Power save mode enabled, PFM/PWM Mode enabled VIN VINA Thermal pad 2, 3 I Supply voltage input (power stage) 8 I Supply voltage input (support circuits) Connect to AGND Copyright (c) 2005-2009, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 5 TPS62110, TPS62111 TPS62112, TPS62113 SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 .................................................................................................................................................... www.ti.com FUNCTIONAL BLOCK DIAGRAM VI Current Limit Comparator + _ Undervoltage Lockout Bias Supply Vina REF Thermal Shutdown + _ Soft Start V I V(COMP) IAVG Comparator REF 1-MHz Oscillator P-Channel Power MOSFET Sawtooth Generator Comparator S + _ R Driver Shoot-Through Logic Control Logic SW N-Channel Power MOSFET Comparator High Comparator Low Comparator High 2 Load Comparator + _ SKIP Comparator + _ PG + _ Comparator High + Gm _ Comparator Low EN + R2 VREF = 1.153 V + _ + _ (See Note A) FB A. 6 LBO _ R1 Compensation 1.256 V LBI PGND GND For the adjustable version (TPS62110), the internal feedback divider is disabled and the FB pin is directly connected to the internal GM amplifier. Submit Documentation Feedback Copyright (c) 2005-2009, Texas Instruments Incorporated Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 TPS62110, TPS62111 TPS62112, TPS62113 www.ti.com .................................................................................................................................................... SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 TYPICAL CHARACTERISTICS Table of Graphs FIGURE Efficiency vs Output current (5 V) 1, 2 Efficiency vs Output current (3.3 V) Maximum output current vs Input voltage Efficiency vs Output current (1.8 V) 7, 8 Efficiency vs Output current (1.5 V) 9, 10 3, 4, 5 6 Line transient response 11 Load transient response 12 Output ripple 13 Start-up timing 14 Switching frequency vs Input voltage 15 Quiescent current vs Input voltage 16 Graphs with VO = 1.8 V were taken using the circuit according to Figure 20. TPS62112 EFFICIENCY vs OUTPUT CURRENT TPS62112 EFFICIENCY vs OUTPUT CURRENT 100 100 90 90 80 80 8.4 V 70 Efficiency - % Efficiency - % 8.4 V 60 12 V 50 15 V 40 30 12 V 60 50 15 V 40 30 VO = 5 V TA = 25oC PWM Mode 20 10 0 0.0001 70 0.001 0.01 0.1 IO - Output Current- A Figure 1. Copyright (c) 2005-2009, Texas Instruments Incorporated 1 20 10 10 VO = 5 V TA = 25oC PFM Mode 0 0.0001 0.001 0.01 0.1 1 10 IO - Output Current- A Figure 2. Submit Documentation Feedback Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 7 TPS62110, TPS62111 TPS62112, TPS62113 SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 .................................................................................................................................................... www.ti.com TPS62111 EFFICIENCY vs OUTPUT CURRENT TPS62111 EFFICIENCY vs OUTPUT CURRENT 100 100 90 90 4.2 V 80 80 70 Efficiency - % Efficiency - % 4.2 V 8.4 V 60 5V 50 12 V 40 30 5V 70 60 8.4 V 50 12 V 40 30 VO = 3.3 V o TA = 25 C PWM Mode 20 10 0 0.0001 0.001 0.01 0.1 1 VO = 3.3 V o TA = 25 C PFM Mode 20 10 0 0.0001 10 0.001 0.01 IO - Output Current- A Figure 3. Figure 4. TPS62111 EFFICIENCY vs OUTPUT CURRENT TPS62111 MAXIMUM OUTPUT CURRENT vs INPUT VOLTAGE VO = 3.3 V SYNC = 1.4 MHz TA = 25oC PFM Mode IO - Output Current - mA Efficiency - % 80 70 8.4 V 60 5V 50 12 V 40 30 20 10 0 0.0001 8 0.001 0.01 0.1 1 10 2000 1900 1800 1700 1600 1500 1400 1300 1200 1100 1000 900 800 700 600 500 400 300 200 100 0 3.2 3.6 4 4.4 4.8 IO - Output Current- A VI - Input Voltage- V Figure 5. Figure 6. Submit Documentation Feedback 10 1 IO - Output Current- A 100 90 0.1 5.2 5.6 6 Copyright (c) 2005-2009, Texas Instruments Incorporated Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 TPS62110, TPS62111 TPS62112, TPS62113 www.ti.com .................................................................................................................................................... SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 TPS62110 EFFICIENCY vs OUTPUT CURRENT TPS62110 EFFICIENCY vs OUTPUT CURRENT 100 100 90 90 80 4.2 V 80 5V 70 60 Efficiency - % Efficiency - % 4.2 V 8.4 V 5V 50 12 V 40 30 8.4 V 60 50 40 12 V 30 VO = 1.8 V o TA = 25 C PWM Mode 20 10 0 0.0001 70 0.001 0.01 0.1 1 VO = 1.8 V o TA = 25 C PFM Mode 20 10 0 0.0001 10 0.001 IO - Output Current- A TPS62110 EFFICIENCY vs OUTPUT CURRENT TPS62110 EFFICIENCY vs OUTPUT CURRENT 90 90 4.2 V 70 5V 8.4 V 50 40 12 V 30 10 4.2 V 70 5V 60 8.4 V 50 40 12 V 30 VO = 1.5 V o TA = 25 C PWM Mode 20 10 0 0.0001 1 80 Efficiency - % Efficiency - % Figure 8. 100 60 0.1 Figure 7. 100 80 0.01 IO - Output Current- A 0.001 0.01 0.1 IO - Output Current- A Figure 9. Copyright (c) 2005-2009, Texas Instruments Incorporated 1 VO = 1.5 V o TA = 25 C PFM Mode 20 10 10 0 0.0001 0.001 0.01 0.1 1 10 IO - Output Current- A Figure 10. Submit Documentation Feedback Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 9 TPS62110, TPS62111 TPS62112, TPS62113 SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 .................................................................................................................................................... www.ti.com TPS62111 LINE TRANSIENT C1 = 5 V/div TPS62111 LOAD TRANSIENT VI = 8.4 V VO = 3.3 V ILOAD = 150 mA to 1350 mA TA = 25C VO = 50 mV/div C2 = 50 mV/div IO = 500 mA/div VI = 7.2 V to 12 V VO = 3.3 V ILOAD = 800 mA TA = 25C t - Time = 2 ms/div VI = 8.4 V, VO = 3.3 V t - Time = 20 s/div Figure 11. Figure 12. TPS62111 OUTPUT RIPPLE TPS62111 START-UP TIMING ILOAD = 100 mA, TA = 25C VI = 12 V, VO = 3.3 V ILOAD = 800 mA, TA = 25C CH1 = 20 mV/div CH1 = 10 V/div CH2 = 5 V/div CH2 = 1 V/div CH3 = 5 V/div CH4 = 500 mA/div CH4 = 200 mA/div t - Time = 5 s/div Figure 13. 10 Submit Documentation Feedback t - Time = 200 s/div Figure 14. Copyright (c) 2005-2009, Texas Instruments Incorporated Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 TPS62110, TPS62111 TPS62112, TPS62113 www.ti.com .................................................................................................................................................... SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 SWITCHING FREQUENCY vs INPUT VOLTAGE QUIESCENT CURRENT vs INPUT VOLTAGE 1000 50 VO = 12 V IO = 100 mA 45 85oC 40 980 o 970 25 C 960 o -40 C 950 940 930 Quiescent Current - mA Switching Frequency - kHz 990 35 30 20 910 5 4 5 6 0 7 8 9 10 11 12 13 14 15 16 17 VI - Input Voltage - V -40oC 15 10 3 25oC 25 920 900 o 85 C 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 VI - Input Voltage - V Figure 15. Figure 16. The graphs were generated using the EVM with the setup according to Figure 17 unless otherwise noted. The output voltage divider was adjusted according to Table 4. Graphs for an output voltage of 5 V and 3.3 V were generated using TPS62111 and TPS62112 with R1 = 0 and R2 = open. TDK 6.8 mH SLF7032T-6R8M1R6 Vbat open CI 10 mF / 25 V TDK C3225X5R1E106K TPS62110 VIN VIN EN SW SW VO 1 MW 1 MW R1 Cff PG VINA CO 22 mF / 16 V TDK C3225X7R1C226M 1 mF AGND LBO FB LBI R2 261 kW SYNC VIN or GND GND GND PwPD PGND PGND Figure 17. Test Setup Copyright (c) 2005-2009, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 11 TPS62110, TPS62111 TPS62112, TPS62113 SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 .................................................................................................................................................... www.ti.com DETAILED DESCRIPTION OPERATION The TPS6211x is a synchronous step-down converter that operates with a 1-MHz fixed-frequency pulse-width modulation (PWM) at moderate-to-heavy load currents and enters the power-save mode at light load current. During PWM operation, the converter uses a unique fast-response voltage-mode control scheme with input-voltage feedforward. Good line and load regulation is achieved with the use of small input and output ceramic capacitors. At the beginning of each clock cycle initiated by the clock signal (S), the P-channel MOSFET switch is turned on, and the inductor current ramps up until the comparator trips and the control logic turns the switch off. The switch is turned off by the current-limit comparator if the current limit of the P-channel switch is exceeded. After the dead time prevents current shoot through, the N-channel MOSFET rectifier is turned on, and the inductor current ramps down. The next cycle is initiated by the clock signal turning off the N-channel rectifier, and turning on the P-channel switch. The error amplifier as well as the input voltage determines the rise time of the sawtooth generator. Therefore, any change in input voltage or output voltage directly controls the duty cycle of the converter, giving a very good line- and load-transient regulation. CONSTANT-FREQUENCY MODE OF OPERATION (SYNC = HIGH) In constant-frequency mode, the output voltage is regulated by varying the duty cycle of the PWM signal in the range of 100% to 10%. Connecting the SYNC pin to a voltage greater than 1.5 V forces the converter to operate permanently in the PWM mode even at light or no-load currents. The advantage is that the converter operates with a fixed switching frequency that allows simple filtering of the switching frequency for noise-sensitive applications. In this mode, the efficiency is lower compared to the power-save mode during light loads. The N-MOSFET of the devices stays on even when the current into the output drops to zero. This prevents the device from going into discontinuous mode, and the device transfers unused energy back to the input. Therefore, there is no ringing at the output, which usually occurs in discontinuous mode. The duty cycle range in constant-frequency mode is 100% to 10%. It is possible to switch from forced PWM mode to the power-save mode during operation by pulling the SYNC pin LOW. The flexible configuration of the SYNC pin during operation of the device allows efficient power management by adjusting the operation of the TPS6211x to the specific system requirements. POWER-SAVE MODE OF OPERATION (SYNC = LOW) As the load current decreases, the converter enters the power-save mode of operation. During power-save mode, the converter operates with reduced switching frequency in pulse-frequency modulation (PFM), and with a minimum quiescent current to maintain high efficiency. Whenever the average output current goes below the skip threshold, the converter enters the power-save mode. The average current depends on the input voltage. It is about 200 mA at low input voltages and up to 400 mA with maximum input voltage. The average output current must be below the threshold for at least 32 clock cycles to enter the power-save mode. During the power-save mode, the output voltage is monitored with a comparator, and the output voltage is regulated to a typical value between the nominal output voltage and 0.8% above the nominal output voltage. When the output voltage falls below the nominal output voltage, the P-channel switch turns on. The P-channel switch is turned off as the peak switch current is reached. The N-channel rectifier is turned on, and the inductor current ramps down. As the inductor current approaches zero, the N-channel rectifier is turned off and the switch is turned on starting the next pulse. When the output voltage cannot be reached with a single pulse, the device continues to switch with its normal operating frequency until the comparator detects the output voltage to be 0.8% above the nominal output voltage. This control method reduces the quiescent current to 20 A (typical), and reduces the switching frequency to a minimum that achieves the highest converter efficiency. 12 Submit Documentation Feedback Copyright (c) 2005-2009, Texas Instruments Incorporated Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 TPS62110, TPS62111 TPS62112, TPS62113 www.ti.com .................................................................................................................................................... SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 DETAILED DESCRIPTION (continued) 1.6% 0.8% VO (nominal) -1.6% t Figure 18. Power-Save Mode Output-Voltage Thresholds The typical PFM (SKIP) current threshold for the TPS6211x is given by: VI ISKIP 25 W (1) Equation 1 is valid for input voltages up to 7 V. For higher voltages, the skip current threshold is not increased further. The converter enters the fixed-frequency PWM mode as soon as the output voltage falls below VO - 1.6% (nominal). SOFT START The TPS6211x has an internal soft-start circuit that limits the inrush current during start-up. This prevents possible voltage drops of the input voltage when a battery or a high-impedance power source is connected to the input of the TPS6211x. The soft start is implemented as a digital circuit increasing the switch current in steps of 300 mA, 600 mA, 1200 mA. The typical switch current limit is 2.4 A. Therefore, the start-up time depends on the output capacitor and load current. Typical start-up time with a 22-F output capacitor and 800-mA load current is 1 ms. 100% DUTY-CYCLE, LOW-DROPOUT OPERATION The TPS6211x offers the lowest possible input-to-output voltage difference while still maintaining operation with the use of the 100% duty-cycle mode. In this mode, the P-channel switch is constantly turned on. This is particularly useful in battery-powered applications to achieve the longest operation time, taking full advantage of the whole battery voltage range. The minimum input voltage to maintain regulation depends on the load current and output voltage, and is calculated as: VI min = VO max + IO max g (rDS(on) max + R(L) ) (2) with: IOmax = maximum output current plus inductor ripple current rDS(on)max = maximum P-channel switch rDS(on) R(L) = dc resistance of the inductor VOmax = nominal output voltage plus maximum output-voltage tolerance Copyright (c) 2005-2009, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 13 TPS62110, TPS62111 TPS62112, TPS62113 SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 .................................................................................................................................................... www.ti.com DETAILED DESCRIPTION (continued) ENABLE Logic low on EN forces the TPS6211x into shutdown. In shutdown, the power switch, drivers, voltage reference, oscillator, and all other functions are turned off. The supply current is reduced to less than 2 A in the shutdown mode. When the device is in thermal shutdown, the band gap is forced to be switched on even if the device is set into shutdown by pulling EN to GND. If an output voltage is present when the device is disabled, which could be due to an external voltage source or a super capacitor, the reverse leakage current is specified under electrical characteristics. Pulling the enable pin high starts up the TPS6211x with the soft start. If the EN pin is connected to any voltage other than VI or GND, an increased leakage current of typically 10 A and up to 20 A can occur. UNDERVOLTAGE LOCKOUT The undervoltage lockout circuit prevents the device from misoperation at low-input voltages. It prevents the converter from turning on the switch or rectifier MOSFET under undefined conditions. The minimum input voltage to start up the TPS6211x is 3.4 V (worst case). The device shuts down at 2.8 V minimum. SYNCHRONIZATION If no clock signal is applied, the converter operates with a typical switching frequency of 1 MHz. It is possible to synchronize the converter to an external clock within a frequency range from 0.8 MHz to 1.4 MHz. The device automatically detects the rising edge of the first clock and synchronizes immediately to the external clock. If the clock signal is stopped, the converter automatically switches back to the internal clock and continues operation. The switchover is initiated if no rising edge on the SYNC pin is detected for a duration of four clock cycles. Therefore, the maximum delay time can be 6.25 s if the internal clock has its minimum frequency of 800 kHz. If the device is synchronized to an external clock, the power-save mode is disabled, and the devices stay in forced PWM mode. Connecting the SYNC pin to the GND pin enables the power-save mode. The converter operates in the PWM mode at moderate-to-heavy loads, and in the PFM mode during light loads, which maintains high efficiency over a wide load-current range. POWER-GOOD COMPARATOR The power-good (PG) comparator has an open-drain output capable of sinking 1 mA (typical). The PG is only active when the device is enabled (EN = high). When the device is disabled (EN = low), the PG pin is pulled to GND. The PG output is only valid after a 250-s delay when the device is enabled and the supply voltage is greater than the undervoltage lockout V(UVLO). PG is low during the first 250 s after shutdown and in shutdown. The PG pin becomes active-high when the output voltage exceeds 98.4% (typical) of its nominal value. Leave the PG pin unconnected when not used. LOW-BATTERY DETECTOR (Standard Version) The low-battery output (LBO) is an open-drain type which goes low when the voltage at the low-battery input (LBI) falls below the trip point of 1.256 V 1.5%. The voltage at which the low-battery warning is issued can be adjusted with a resistive divider as shown in Figure 19. The sum of resistors (R1 + R2) as well as the sum of (R5 + R6) is recommended to be in the 100-k to 1-M range for high efficiency at low output current. An external pullup resistor can be connected to OUT, or any other voltage rail in the voltage range of 0 V to 16 V. During start-up, the LBO output signal is invalid for the first 500 s. LBO is high-impedance when the device is disabled. If the low-battery comparator function is not used, connect LBI to ground. The low-battery detector is disabled when the device is disabled. The logic level of the LBO pin is not defined for the first 500 s after EN is pulled high. When the LBI is used to supervise the battery voltage and shut down the TPS62113 at low-input voltages, the battery voltage rises when the current drops to zero. The implemented hysteresis on the LBI pin may not be sufficient for all types of batteries. Figure 19 shows how an additional external hysteresis can be implemented. 14 Submit Documentation Feedback Copyright (c) 2005-2009, Texas Instruments Incorporated Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 TPS62110, TPS62111 TPS62112, TPS62113 www.ti.com .................................................................................................................................................... SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 DETAILED DESCRIPTION (continued) 6.8 mH VI = 4.3 V to 17 V 2 3 4 TPS62110 VIN VIN EN SW SW 15 R3 R5 8 CI = 10 mF 25 V PG VINA 1 mF 9 7 5 R6 VO = 3.3 V 14 AGND 13 LBO 6 FB 10 LBI SYNC R4 R1 560 kW Cff 10 pF CO = 22 mF 6.3 V R2 300 kW R7 GND GND PwPD PGND PGND 11 12 16 1 Figure 19. LBI With Increased Hysteresis ENABLE/Low-Battery Detector (Enhanced Version) TPS62113 Only The TPS62113 offers an enhanced LBI functionality to provide a precise, user-programmable undervoltage shutdown. No additional supply voltage supervisor (SVS) is needed to provide this function. When the enable (EN) pin is pulled high, only the internal bandgap voltage reference is switched on to provide a reference source for the LBI comparator. As long as the voltage at LBI is less than the LBI trip point, all other internal circuits are shut down, reducing the supply current to 10 A. As soon as input voltage at LBI rises above the LBI trip point of 1.256 V, the device is completely enabled and starts switching. NO-LOAD OPERATION When the converter operates in the forced PWM mode and there is no load connected to the output, the converter regulates the output voltage by allowing the inductor current to reverse for a short time. THEORY OF OPERATION / DESIGN PROCEDURE Table 1. List of Inductors MANUFACTURER Coilcraft PART NO. INDUCTANCE DC RESISTANCE SATURATION CURRENT MSS6132-682 6.8 H 65 m (max) HA3808-AL 6.8 H 99 m (typ) 4.4A Epcos B82462G4682M 6.8 H 50 m (max) 1.5 A Sumida CDRH5D28-6R2 6.2 H 33 m (typ) 1.8 A SLF6028T-6R8M1R5 6.8 H 35 m (typ) 1.5 A SLF7032T-6R8M1R6 6.8 H 41 m (typ) 1.6 A 7447789006 6.8 H 44 m (typ) 2.75 A 7447779006 6.8 H 33 m (typ) 3.3 A 744053006 6.2 H 45 m (typ) 1.8 A TDK Wurth 1.5 A Inductor Selection The control loop of the TPS6211x family requires a certain value for the output inductor and the output capacitor for stable operation. As long as the nominal value of L x C 6.2 H x 22 F, the control loop has enough phase margin and the device is stable. Reducing the inductor value without increasing the output capacitor (or vice versa) may cause stability problems. There are applications where it may be useful to increase the value of the Copyright (c) 2005-2009, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 15 TPS62110, TPS62111 TPS62112, TPS62113 SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 .................................................................................................................................................... www.ti.com output capacitor, e.g., for a low-transient output-voltage change. From a stability point of view, the inductor value could be decreased to keep the L x C product constant. However, there are drawbacks if the inductor value is decreased. A low inductor value causes a high inductor ripple current, and therefore reduces the maximum dc output current. Table 2 gives the advantages and disadvantages when designing the inductor and output capacitor. Table 2. Advantages and Disadvantages When Designing the Inductor and Output Capacitor INFLUENCE ON STABILITY ADVANTAGE DISADVANTAGE Less output voltage ripple Increase Cout (>22 F) Uncritical Decrease Cout (<22 F) Critical Increase inductor value > 6.8 H also Less output voltage overshoot / undershoot during load transient None Higher output voltage ripple High output voltage overshoot / undershoot during load transient None Less gain and phase margin Increase L (>6.8 H) Uncritical Critical Decrease L (<6.8 H) Increase output capacitor value > 22 F also Less inductor current ripple More energy stored in the inductor higher voltage overshoot during load transient Higher dc output current possible if operated close to the current limit Smaller current rise higher voltage undershoot during load transient do not decrease the value of Cout due to these effects Small voltage overshoot / undershoot during load transient High inductor-current ripple especially at high input voltage and low output voltage As shown in Table 2, the inductor value can be increased to higher values. For good performance, the peak-to-peak inductor-current ripple should be less than 30% of the maximum dc output current. Especially at input voltages above 12 V, it makes sense to increase the inductor value in order to keep the inductor-current ripple low. In such applications, the inductor value can be increased to 10 H or 22 H. Values above 22 H should be avoided in order to keep the voltage overshoot during load transient in an acceptable range. After choosing the inductor value, two additional inductor parameters should be considered: 1. current rating of the inductor 2. dc resistance The dc resistance of the inductance directly influences the efficiency of the converter. Therefore, an inductor with lowest dc resistance should be selected for highest efficiency. In order to avoid saturation of the inductor, the inductor should be rated at least for the maximum output current plus the inductor ripple current which is calculated as: V 1- O DI VI DIL = VO IL max = IO max + L Lf 2 (3) where: f = Switching frequency (1000 kHz typical) L = Inductor value IL = Peak-to-peak inductor ripple current IL(max) = Maximum inductor current The highest inductor current occurs at maximum VI. A more-conservative approach is to select the inductor current rating just for the maximum switch current of the TPS6211x, which is 2.4 A (typically). See Table 1 for recommended inductors. 16 Submit Documentation Feedback Copyright (c) 2005-2009, Texas Instruments Incorporated Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 TPS62110, TPS62111 TPS62112, TPS62113 www.ti.com .................................................................................................................................................... SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 OUTPUT-CAPACITOR SELECTION A 22-F (typical) output capacitor is needed with a 6.8-H inductor. For an output voltage greater than 5 V, a 33-F (minimum) output capacitor is required for stability. For best performance, a low-ESR ceramic output capacitor is needed. Just for completeness, the RMS ripple current is calculated as: V 1- O VI 1 IRMS (CO ) = VO Lf 2 3 (4) The overall output ripple voltage is the sum of the voltage spike caused by the output capacitor ESR plus the voltage ripple caused by charging and discharging the output capacitor: V 1- O o VI ae 1 DVO = VO c + RESR / Lf e 8 CO f o (5) where the highest output-voltage ripple occurs at the highest input voltage VI. INPUT-CAPACITOR SELECTION The nature of the buck converter is a pulsating input current; therefore, a low ESR input capacitor is required for best input voltage filtering and for minimizing the interference with other circuits caused by high input-voltage spikes. The input capacitor should have a minimum value of 10 F and can be increased without any limit for better input-voltage filtering. The input capacitor should be rated for the maximum input ripple current calculated as: IRMS = IO max VO ae V o c1 - O / VI e VI o (6) The worst-case RMS ripple current occurs at D = 0.5 and is calculated as: IRMS = IO/2. Ceramic capacitors show a good performance because of their low ESR value, and they are less sensitive against voltage transients compared to tantalum capacitors. Place the input capacitor as close as possible to the input pin of the IC for best performance. FEEDFORWARD-CAPACITOR SELECTION The feedforward capacitor (Cff) is needed to compensate for parasitic capacitance from the feedback pin to GND. Typically, a value of 4.7 pF to 22 pF is needed for an output voltage divider with a equivalent resistance (R1 in parallel with R2) in the 150-k range. The value can be chosen based on best transient performance and lowest output-voltage ripple in PFM mode. RECOMMENDED CAPACITORS It is recommended that only X5R or X7R ceramic capacitors be used as input/output capacitors. Ceramic capacitors show a dc-bias effect. This effect reduces the effective capacitance when a dc-bias voltage is applied across a ceramic capacitor, as on the output and input capacitor of a dc/dc converter. The effect may lead to a significant capacitance drop, especially for high input/output voltages and small capacitor packages. See the manufacturer's data sheet about the performance with a dc bias voltage applied. It may be necessary to choose a higher voltage rating or nominal capacitance value in order to get the required value at the operating point. The capacitors listed in Table 3 have been tested with the TPS62110 with good performance. Table 3. List of Capacitors MANUFACTURER Taiyo Yuden PART NUMBER SIZE VOLTAGE CAPACITANCE TMK316BJ106KL 1206 25 V 10 F EMK325BJ226KM 1210 16 V 22 F Copyright (c) 2005-2009, Texas Instruments Incorporated TYPE Ceramic Submit Documentation Feedback Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 17 TPS62110, TPS62111 TPS62112, TPS62113 SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 .................................................................................................................................................... www.ti.com Table 3. List of Capacitors (continued) MANUFACTURER PART NUMBER TDK C3225X7R1C226M C3225X5R1E106M C3216X5R1E106MT 18 Submit Documentation Feedback SIZE 1210 1206 VOLTAGE CAPACITANCE 25 V 10 F 16 V 22 F 25 V 10 F TYPE Ceramic Copyright (c) 2005-2009, Texas Instruments Incorporated Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 TPS62110, TPS62111 TPS62112, TPS62113 www.ti.com .................................................................................................................................................... SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 APPLICATION INFORMATION 6.8 mH VI = 3.5 V to 17 V 2 TPS62110 VIN VIN EN 3 4 SW SW 15 R3 1 MW R5 8 CI = 10 mF 25 V PG VINA 1 mF 9 AGND 7 5 R6 13 LBO 6 FB 10 LBI VO = 1.8 V 14 R4 1 MW Cff 10 pF R1 220 kW CO = 2 x 22 mF 6.3 V (See Note A) R2 390 kW SYNC GND GND PwPD PGND PGND 11 A. 16 1 12 For an output voltage lower than 2.5 V, an output capacitor of 33 F or greater is recommended to improve load transient. Figure 20. Standard Connection for Adjustable Version VO = VFB ae V R1 = R2 c O e VFB R1 + R2 R2 o / - R2 o (7) VFB = 1.153 V Table 4. Recommended Resistors OUTPUT VOLTAGE R1 R2 NOMINAL VOLTAGE TYPICAL Cff 9V 680 k 100 k 8.993 V 22 pF 5V 510 k 150 k 5.073 V 10 pF 3.3 V 560 k 300 k 3.305 V 10 pF 2.5 V 390 k 330 k 2.515 V 10 pF 1.8 V 220 k 390 k 1.803 V 10 pF 1.5 V 100 k 330 k 1.502 V 10 pF 6.8 mH VI = 5.5 V to 17 V 2 3 4 8 CI = 10 mF 25 V TPS62112 15 VIN VIN EN SW SW VINA PG 1 MW 1 mF 9 7 5 VO = 5 V 14 13 LBO 6 FB 10 CO = 22 mF 10 V AGND LBI SYNC GND GND PwPD PGND PGND 11 12 1 16 Figure 21. Standard Connection for Fixed-Voltage Version Copyright (c) 2005-2009, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 19 TPS62110, TPS62111 TPS62112, TPS62113 SLVS585A - JULY 2005 - REVISED FEBRUARY 2009 .................................................................................................................................................... www.ti.com 6.8 mH VI = 9.3 V to 17 V 2 3 4 8 CI = 10 mF 25 V TPS62110 VIN VIN EN SW SW 7 5 VO = 9 V 14 1 MW PG VINA 1 mF 9 15 AGND 13 LBO 6 FB 10 LBI Cff 22 pF R1 680 kW CO = 33 mF 16 V (See Note A) R2 100 kW SYNC GND GND PwPD PGND PGND 11 A. 12 1 16 For an output voltage greater than 5 V, an output capacitor of 33 F minimum is required for stability. Figure 22. Application With 9-V Output 20 Submit Documentation Feedback Copyright (c) 2005-2009, Texas Instruments Incorporated Product Folder Link(s): TPS62110 TPS62111 TPS62112 TPS62113 PACKAGE OPTION ADDENDUM www.ti.com 4-Nov-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) TPS62110RSAR ACTIVE QFN RSA 16 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Request Free Samples TPS62110RSARG4 ACTIVE QFN RSA 16 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Request Free Samples TPS62110RSAT ACTIVE QFN RSA 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Contact TI Distributor or Sales Office TPS62110RSATG4 ACTIVE QFN RSA 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Contact TI Distributor or Sales Office TPS62111RSAR ACTIVE QFN RSA 16 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples TPS62111RSARG4 ACTIVE QFN RSA 16 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples TPS62111RSAT ACTIVE QFN RSA 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Request Free Samples TPS62111RSATG4 ACTIVE QFN RSA 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Request Free Samples TPS62112RSAR ACTIVE QFN RSA 16 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples TPS62112RSARG4 ACTIVE QFN RSA 16 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples TPS62112RSAT ACTIVE QFN RSA 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Request Free Samples TPS62112RSATG4 ACTIVE QFN RSA 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Request Free Samples TPS62113RSAR ACTIVE QFN RSA 16 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Request Free Samples TPS62113RSAT ACTIVE QFN RSA 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Contact TI Distributor or Sales Office (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 4-Nov-2010 (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TPS62110, TPS62111, TPS62112 : * Automotive: TPS62110-Q1 * Enhanced Product: TPS62110-EP, TPS62111-EP, TPS62112-EP NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects * Enhanced Product - Supports Defense, Aerospace and Medical Applications Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing TPS62110RSAR QFN RSA 16 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3000 330.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2 TPS62110RSAT QFN RSA 16 250 180.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2 TPS62111RSAR QFN RSA 16 3000 330.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2 TPS62111RSAT QFN RSA 16 250 180.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2 TPS62112RSAR QFN RSA 16 3000 330.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2 TPS62112RSAR QFN RSA 16 3000 330.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2 TPS62112RSAT QFN RSA 16 250 180.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2 TPS62113RSAR QFN RSA 16 3000 330.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2 TPS62113RSAR QFN RSA 16 3000 330.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2 TPS62113RSAT QFN RSA 16 250 180.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2 TPS62113RSAT QFN RSA 16 250 180.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS62110RSAR QFN RSA 16 3000 367.0 367.0 35.0 TPS62110RSAT QFN RSA 16 250 210.0 185.0 35.0 TPS62111RSAR QFN RSA 16 3000 367.0 367.0 35.0 TPS62111RSAT QFN RSA 16 250 210.0 185.0 35.0 TPS62112RSAR QFN RSA 16 3000 367.0 367.0 35.0 TPS62112RSAR QFN RSA 16 3000 367.0 367.0 35.0 TPS62112RSAT QFN RSA 16 250 210.0 185.0 35.0 TPS62113RSAR QFN RSA 16 3000 367.0 367.0 35.0 TPS62113RSAR QFN RSA 16 3000 367.0 367.0 35.0 TPS62113RSAT QFN RSA 16 250 210.0 185.0 35.0 TPS62113RSAT QFN RSA 16 250 210.0 185.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated