LM2941S - National Semiconductor - searchdatasheet.com

LM2941/LM2941C

March 9, 2012

1A Low Dropout Adjustable Regulator

General Description

The LM2941 positive voltage regulator features the ability to

source 1A of output current with a typical dropout voltage of

0.5V and a maximum of 1V over the entire temperature range.

Furthermore, a quiescent current reduction circuit has been

included which reduces the ground pin current when the dif-

ferential between the input voltage and the output voltage

exceeds approximately 3V. The quiescent current with 1A of

output current and an input-output differential of 5V is there-

fore only 30mA. Higher quiescent currents only exist when the

regulator is in the dropout mode (VIN − VOUT ≤ 3V).

Designed also for vehicular applications, the LM2941 and all

regulated circuitry are protected from reverse battery instal-

lations or two-battery jumps. During line transients, such as

load dump when the input voltage can momentarily exceed

the specified maximum operating voltage, the regulator will

automatically shut down to protect both the internal circuits

and the load. Familiar regulator features such as short circuit

and thermal overload protection are also provided.

Features

■LLP space saving package

■Output voltage adjustable from 5V to 20V

■Dropout voltage typically 0.5V @ IO = 1A

■Output current in excess of 1A

■Trimmed reference voltage

■Reverse battery protection

■Internal short circuit current limit

■Mirror image insertion protection

■P+ Product Enhancement tested

■TTL, CMOS compatible ON/OFF switch

Connection Diagram and Ordering Information

TO-220 Plastic Package

882302

Top View

Order Number LM2941T or LM2941CT

See NS Package Number TO5A

TO-263 Surface-Mount Package

882308

Order Number LM2941S, LM2941SX or LM2941CS,

LM2941CSX

See NS Package Number TS5B

8-Lead LLP Surface Mount Package

882333

Top View

Ordering Number LM2941LD, LM2941LDX

See NS Package Number LDC08A

LM2941/LM2941C 1A Low Dropout Adjustable Regulator

Absolute Maximum Ratings (Note 1)

If Military/Aerospace specified devices are required,

please contact the Texas Instruments Sales Office/

Distributors for availability and specifications.

Input Voltage (Survival Voltage, ≤ 100ms)

LM2941T, LM2941S, LM2941LD 60V

LM2941CT, LM2941CS 45V

Internal Power Dissipation (Note 4) Internally Limited

Maximum Junction Temperature 150°C

Storage Temperature Range −65°C ≤ TJ ≤ +150°C

Soldering Temperature (Note 9)

TO-220 (T), Wave 260°C, 10s

TO-263 (S) 235°C, 30s

LLP-8 (LD) 235°C, 30s

ESD Rating (Note 2) ±2 kV

Operating Ratings

Maximum Input Voltage 26V

Temperature Range

LM2941T −40°C ≤ TJ ≤ 125°C

LM2941CT 0°C ≤ TJ ≤ 125°C

LM2941S −40°C ≤ TJ ≤ 125°C

LM2941CS 0°C ≤ TJ ≤ 125°C

LM2941LD −40°C ≤ TJ ≤ 125°C

Electrical Characteristics—LM2941T, LM2941S, LM2941LD

5V ≤ VO ≤ 20V, VIN = VO + 5V, CO = 22μF, unless otherwise specified. Specifications in standard typeface apply for TJ = 25°C,

while those in boldface type apply over the full Operating Temperature Range.

Parameter Conditions Typ

LM2941T

LM2941S

LM2941LD

Limit

Units

(Limits)

Reference Voltage 5mA ≤ IO ≤ 1A (Note 7)1.275 1.237/1.211 V(min)

1.313/1.339 V(max)

Line Regulation VO + 2V ≤ VIN ≤ 26V, IO = 5mA 4 10/10 mV/V(max)

Load Regulation 50mA ≤ IO ≤ 1A 7 10/10 mV/V(max)

Output Impedance 100 mADC and 20 mArms

fO = 120Hz 7 mΩ/V

Quiescent Current VO + 2V ≤ VIN < 26V, IO = 5mA 10 15/20 mA(max)

VIN = VO + 5V, IO = 1A 30 45/60 mA(max)

RMS Output Noise,

% of VOUT

10Hz–100kHz

IO = 5mA 0.003 %

Ripple Rejection fO = 120Hz, 1 Vrms, IL = 100mA 0.005 0.02/0.04 %/V(max)

Long Term Stability 0.4 %/1000 Hr

Dropout Voltage IO = 1A 0.5 0.8/1.0 V(max)

IO = 100mA 110 200/200 mV(max)

Short Circuit Current VIN Max = 26V (Note 8)1.9 1.6 A(min)

Maximum Line

Transient

VO Max 1V Above Nominal VO

RO = 100, t ≤ 100ms 75 60/60 V(min)

Maximum Operational

Input Voltage 31 26/26 VDC

Reverse Polarity

DC Input Voltage RO = 100, VO ≥ −0.6V −30 −15/−15 V(min)

Reverse Polarity

Transient Input Voltage t ≤ 100ms, RO = 100Ω −75 −50/−50 V(min)

ON/OFF Threshold

Voltage ON IO ≤ 1A 1.30 0.80/0.80 V(max)

ON/OFF Threshold

Voltage OFF IO ≤ 1A 1.30 2.00/2.00 V(min)

ON/OFF Threshold

Current VON/OFF = 2.0V, IO ≤ 1A 50 100/300 μA(max)

www.ti.com 2

LM2941/LM2941C

Electrical Characteristics—LM2941CT, LM2941CS

5V ≤ VO ≤ 20V, VIN = VO + 5V, CO = 22μF, unless otherwise specified. Specifications in standard typeface apply for TJ = 25°C,

while those in boldface type apply over the full Operating Temperature Range.

Parameter Conditions Typ Limit Units

(Note 6)(Limits)

Reference Voltage 5mA ≤ IO ≤ 1A (Note 7)1.275 1.237/1.211 V(min)

1.313/1.339 V(max)

Line Regulation VO + 2V ≤ VIN ≤ 26V, IO = 5mA 4 10 mV/V(max)

Load Regulation 50mA ≤ IO ≤ 1A 7 10 mV/V(max)

Output Impedance 100 mADC and 20 mArms

fO = 120Hz 7 mΩ/V

Quiescent Current VO + 2V ≤ VIN < 26V, IO = 5mA 10 15 mA(max)

VIN = VO + 5V, IO = 1A 30 45/60 mA(max)

RMS Output Noise,

% of VOUT

10Hz–100kHz

IO = 5mA 0.003 %

Ripple Rejection fO = 120Hz, 1 Vrms, IL = 100mA 0.005 0.02 %/V(max)

Long Term Stability 0.4 %/1000 Hr

Dropout Voltage IO = 1A 0.5 0.8/1.0 V(max)

IO = 100mA 110 200/200 mV(max)

Short Circuit Current VIN Max = 26V (Note 8)1.9 1.6 A(min)

Maximum Line

Transient

VO Max 1V Above Nominal VO

RO = 100Ω, T ≤ 100ms 55 45 V(min)

Maximum Operational

Input Voltage 31 26 VDC

Reverse Polarity

DC Input Voltage RO = 100Ω, VO ≥ −0.6V −30 −15 V(min)

Reverse Polarity

Transient Input Voltage T ≤ 100ms, RO = 100Ω −55 −45 V(min)

ON/OFF Threshold

Voltage ON IO ≤ 1A 1.30 0.80 V(max)

ON/OFF Threshold

Voltage OFF IO ≤ 1A 1.30 2.00 V(min)

ON/OFF Threshold

Current VON/OFF = 2.0V, IO ≤ 1A 50 100 μA(max)

Thermal Performance

Thermal Resistance

Junction-to-Case, θJC

5-Lead TO-220 1 °C/W

5-Lead TO-263 1 °C/W

8–Lead LLP 5.3 °C/W

Thermal Resistance

Junction-to-Ambient, θJA

(Note 4)

5-Lead TO-220 53 °C/W

5-Lead TO-263 (See TO-263 MOUNTING) 73 °C/W

8-Lead LLP (See LLP MOUNTING) 35 °C/W

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions for which the device is

intended to be functional, but device parameter specifications may not be guaranteed under these conditions. For guaranteed specifications and test conditions,

see the Electrical Characteristics.

Note 2: The Human Body Model (HBM) is a 100 pF capacitor discharged through a 1.5kΩ resistor into each pin. Test method is per JESD22–A114.

Note 3: A military RETS specification available upon request. For more information about military-aerospace products, see the Mil-Aero web page at http://

www.national.com/appinfo/milaero/index.html.

Note 4: The maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any ambient temperature is PD =

(TJ(max) − TA)/θJA. If this dissipation is exceeded, the die temperature will rise above 150°C and the LM2941 will go into thermal shutdown. If the TO-263 package

is used, the thermal resistance can be reduced by increasing the P.C. board copper area thermally connected to the package: Using 0.5 square inches of copper

area, θJA is 50°C/W; with 1 square inch of copper area, θJA is 37°C/W; and with 1.6 or more square inches of copper area, θJA is 32°C/W. Thermal performance

for the LLP package was obtained using a JESD51-7 board with six vias, using no airflow and an ambient temperature of 22°C. The value θJA for the LLP package

3 www.ti.com

LM2941/LM2941C

is specifically dependent on PCB trace area, trace material, and the number of layers and thermal vias. For improved thermal resistance and power dissipation

for the LLP package, refer to Application Note AN-1187. It is recommended that 6 vias be placed under the center pad to improve thermal performance.

Note 5: All limits guaranteed at room temperature (standard typeface) and at temperature extremes (boldface type). All limits are used to calculate Outgoing

Quality Level, and are 100% production tested.

Note 6: All limits guaranteed at room temperature (standard typeface) and at temperature extremes (boldface type). All room temperature limits are 100%

production tested. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods.

Note 7: The output voltage range is 5V to 20V and is determined by the two external resistors, R1 and R2. See Typical Application Circuit.

Note 8: Output current capability will decrease with increasing temperature, but will not go below 1A at the maximum specified temperatures.

Note 9: Refer to JEDEC J-STD-020C for surface mount device (SMD) package reflow profiles and conditions. Unless otherwise stated, the temperature and time

are for Sn-Pb (STD) only.

Typical Performance Characteristics

Dropout Voltage

882311

Dropout Voltage vs. Temperature

882312

Output Voltage

882313

Quiescent Current vs. Temperature

882314

www.ti.com 4

LM2941/LM2941C

Quiescent Current

882315

Quiescent Current

882316

Line Transient Response

882317

Load Transient Response

882318

Ripple Rejection

882319

Output Impedance

882320

5 www.ti.com

LM2941/LM2941C

Low Voltage Behavior

882321

Low Voltage Behavior

882322

Output Capacitor ESR

882323

Output at Voltage Extremes

882324

Output at Voltage Extremes

882325

Peak Output Current

882326

www.ti.com 6

LM2941/LM2941C

Maximum Power Dissipation (TO-220)

882327

Maximum Power Dissipation (TO-263)

882329

Definition of Terms

Dropout Voltage: The input-voltage differential at which the

circuit ceases to regulate against further reduction in input

voltage. Measured when the output voltage has dropped

100mV from the nominal value obtained at (VOUT + 5V) input,

dropout voltage is dependent upon load current and junction

temperature.

Input Voltage: The DC voltage applied to the input terminals

with respect to ground.

Input-Output Differential: The voltage difference between

the unregulated input voltage and the regulated output volt-

age for which the regulator will operate.

Line Regulation: The change in output voltage for a change

in the input voltage. The measurement is made under condi-

tions of low dissipation or by using pulse techniques such that

the average chip temperature is not significantly affected.

Load Regulation: The change in output voltage for a change

in load current at constant chip temperature.

Long Term Stability: Output voltage stability under accel-

erated life-test conditions after 1000 hours with maximum

rated voltage and junction temperature.

Output Noise Voltage: The rms AC voltage at the output,

with constant load and no input ripple, measured over a spec-

ified frequency range.

Quiescent Current: That part of the positive input current

that does not contribute to the positive load current. The reg-

ulator ground lead current.

Ripple Rejection: The ratio of the peak-to-peak input ripple

voltage to the peak-to-peak output ripple voltage.

Temperature Stability of VO: The percentage change in

output voltage for a thermal variation from room temperature

to either temperature extreme.

7 www.ti.com

LM2941/LM2941C

Application Hints

OUTPUT CAPACITOR

A Tantalum capacitor with a minimum capacitance value of

22 μF, and ESR in the range of 0.01Ω to 5Ω, is required at

the output pin for loop stability. It must be located less than 1

cm from the device. There is no limitation on any additional

capacitance.

Alternately, a high quality X5R/X7R 22 μF ceramic capacitor

may be used for the output capacitor only if an appropriate

value of series resistance is added to simulate the ESR re-

quirement. The ceramic capacitor selection must include an

appropriate voltage de-rating of the capacitance value due to

the applied output voltage. The series resistor (for ESR sim-

ulation) should be in the range of 0.1Ω to 1.0Ω.

SETTING THE OUTPUT VOLTAGE

The output voltage range is 5V to 20V and is set by the two

external resistors, R1 and R2. See the Typical Applications.

The output voltage is given by the formula:

VOUT = VREF x ((R1+R2) / R1)

where VREF is typically 1.275V.

Using 1.00 kΩ for R1 will ensure that the bias current error of

the adjust pin will be negligible. Using a R1 value higher than

10 kΩ may cause the output voltage to shift across tempera-

ture due to variations in the adjust pin bias current.

Calculating the upper resistor (R2) value of the pair when the

lower resistor (R1) value is known is accomplished with the

following formula:

R2 = R1 x ((VOUT / VREF) - 1)

The resistors used for R1 and R2 should be high quality, tight

tolerance, and with matching temperature coefficients. It is

important to remember that, although the value of VREF is

guaranteed, the final value of VOUT is not. The use of low

quality resistors for R1 and R2 can easily produce a VOUT

value that is unacceptable.

ON/OFF

The ON/OFF pin has no internal pull-up or pull-down to es-

tablish a default condition and, as a result, this pin must be

terminated externally, either actively or passively.

The ON/OFF pin requires a low level to enable the output, and

a high level to disable the output. To ensure reliable operation,

the ON/OFF pin voltage must rise above the maximum ON/

OFF(OFF) voltage threshold (2.00V) to disable the output, and

must fall below the minimum ON/OFF(ON) voltage threshold

(0.80V) to enable the output. If the ON/OFF function is not

needed this pin can be connected directly to Ground.

If the ON/OFF pin is being pulled to a high state through a

series resistor, an allowance must be made for the ON/OFF

pin current that will cause a voltage drop across the pull-up

resistor.

THERMAL OVERLOAD PROTECTION

The LM2941 incorporates a linear form of thermal protection

that limits the junction temperature (TJ) to typically 155°C.

Should the LM2941 see a fault condition that results in ex-

cessive power dissipation and the junction temperature ap-

proaches 155°C, the device will respond by reducing the

output current (which reduces the power dissipation) to hold

the junction temperature at 155°C.

Thermal Overload protection is not a guaranteed operating

condition. Operating at, or near to, the Thermal Overload

condition for any extended period of time is not encouraged,

or recommended, as this may shorten the lifetime of the de-

vice.

POWER DISSIPATION

Consideration should be given to the maximum power dissi-

pation (PD(MAX)) which is limited by the maximum operating

junction temperature (TJ(MAX)) of 125°C, the maximum oper-

ating ambient temperature (TA(MAX)) of the application, and

the thermal resistance (θJA) of the package. Under all possible

conditions, the junction temperature (TJ) must be within the

range specified in the Operating Ratings. The total power dis-

sipation of the device is given by:

PD = ( (VIN − VOUT) x IOUT) + (VIN x IGND)

where IGND is the operating ground pin current of the device

(specified under Electrical Characteristics).

The maximum allowable junction temperature rise (ΔTJ) de-

pends on the maximum expected ambient temperature

(TA(MAX)) of the application, and the maximum allowable junc-

tion temperature (TJ(MAX)):

ΔTJ = TJ(MAX) − TA(MAX)

The maximum allowable value for junction to ambient Ther-

mal Resistance, θJA, required to keep the junction tempera-

ture, TJ, from exceeding maximum allowed can be calculated

using the formula:

θJA = ΔTJ / PD(MAX)

The maximum allowable power dissipation, PD(MAX), required

allowed for a specific ambient temperature can be calculated

using the formula:

PD(MAX) = ΔTJ / θJA

Additional information for thermal performance of surface

mount packages can be found in AN-1520: A Guide to Board

Layout for Best Thermal Resistance for Exposed Packages,

AN-1187: Leadless Leadframe Package (LLP), and AN-2020:

Thermal Design By Insight, Not Hindsight .

TO-263 MOUNTING

The thermal dissipation of the TO-263 package is directly re-

lated to the printed circuit board construction and the amount

of additional copper area connected to the TAB.

The TAB on the bottom of the TO-263 package is connected

to the die substrate via a conductive die attach adhesive, and

to device pin 3. As such, it is strongly recommend that the

TAB area be connected to copper area directly under the TAB

that is extended into the ground plane via multiple thermal

vias. Alternately, but not recommended, the TAB may be left

floating (i.e. no direct electrical connection). The TAB must

not be connected to any potential other than ground.

For the LM2941S in the TS5B TO-263 package, the junction-

to-case thermal rating, θJC, is 1°C/W, where the CASE is

defined as the bottom of the package at the center of the TAB

area. The junction-to-ambient thermal performance for the

LM2941S in the TO-263 package, using the JEDEC JESD51

standards is summarized in the following table:

www.ti.com 8

LM2941/LM2941C

Board

Type

Thermal

Vias θJC θJA

JEDEC

2-Layer

JESD 51-3

None 1°C/W 73°C/W

JEDEC

4-Layer

JESD 51-7

1 1°C/W 35°C/W

2 1°C/W 30°C/W

4 1°C/W 26°C/W

8 1°C/W 24°C/W

0 20 40 60 80 100

POWER DISSIPATION (W)

AMBIENT TEMPERATURE (°C)

LM2941S (TO-263)

θJA = 35°C/W

θJA = 30°C/W

θJA = 26°C/W

θJA = 24°C/W

882334

FIGURE 1. PD(MAX) vs TA for LM2941S (TO-263)

LLP MOUNTING

The LDC08A (Pullback) 8-Lead LLP package requires spe-

cific mounting techniques which are detailed in Application

Note # 1187. Referring to the section PCB Design Recom-

mendations in AN-1187 (Page 5), it should be noted that the

pad style which should be used with the LLP package is the

NSMD (non-solder mask defined) type.

The thermal dissipation of the LLP package is directly related

to the printed circuit board construction and the amount of

additional copper area connected to the DAP.

The DAP (exposed pad) on the bottom of the LLP package is

connected to the die substrate via a conductive die attach

adhesive, and to device pin 2 and pin 7. As such, it is strongly

recommend that the DAP area be connected copper area di-

rectly under the DAP that is extended into the ground plane

via multiple thermal vias. Alternately, but not recommended,

the DAP area may be left floating (i.e. no direct electrical con-

nection). The DAP area must not be connected to any poten-

tial other than ground.

For the LM2941LD in the LDC08A 8-Lead LLP package, the

junction-to-case thermal rating, θJC, is 5.3°C/W, where the

CASE is defined as the bottom of the package at the center

of the DAP area. The junction-to-ambient thermal perfor-

mance for the LM2941LD in the LDC08A 8-Lead LLP pack-

age, using the JEDEC JESD51 standards is summarized in

the following table:

Board

Type

Thermal

Vias θJC θJA

JEDEC

2-Layer

JESD 51-3

None 5.3°C/W 181°C/W

JEDEC

4-Layer

JESD 51-7

1 5.3°C/W 58°C/W

2 5.3°C/W 49°C/W

4 5.3°C/W 40°C/W

6 5.3°C/W 35°C/W

0 20 40 60 80 100

POWER DISSIPATION (W)

AMBIENT TEMPERATURE (°C)

LM2941LD (LLP)

θJA = 35°C/W

θJA = 40°C/W

θJA = 49°C/W

θJA = 58°C/W

882335

FIGURE 2. PD(MAX) vs TA for LM2941LD (LLP)

9 www.ti.com

LM2941/LM2941C

Typical Applications

5V to 20V Adjustable Regulator

882303

Note: Using 1k for R1 will ensure that the bias current error from the adjust pin will be negligible. Do not bypass R1 or R2. This will lead to instabilities.

* Required if regulator is located far from power supply filter.

** COUT must be at least 22μF to maintain stability. May be increased without bound to maintain regulation during transients. Locate as close as possible to the

regulator. This capacitor must be rated over the same operating temperature range as the regulator and the ESR is critical; see curve.

1A Switch

882306

*** To assure shutdown, select Resistor R3 to guarantee at least 300μA of pull-up current when S1 is open. (Assume 2V at the ON/OFF pin.)

www.ti.com 10

LM2941/LM2941C

Equivalent Schematic Diagram

882301

11 www.ti.com

LM2941/LM2941C

Physical Dimensions inches (millimeters) unless otherwise noted

Order Number LM2941T or LM2941CT

NS Package Number T05A

TO-263 5-Lead Plastic Surface Mount Package

Order Number LM2941S, LM2941SX, LM2941CS or LM2941CSX

NS Package Number TS5B

www.ti.com 12

LM2941/LM2941C

8-Lead LLP Surface Mount Package

Order Number LM2941LD, LM2941LDX

NS Package Number LDC08A

13 www.ti.com

LM2941/LM2941C

Notes

LM2941/LM2941C 1A Low Dropout Adjustable Regulator

www.ti.com

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,

and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should

obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are

sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard

warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where

mandated by government requirements, testing of all parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and

applications using TI components. To minimize the risks associated with customer products and applications, customers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,

or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a

warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual

property of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied

by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive

business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional

restrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all

express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not

responsible or liable for any such statements.

TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably

be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing

such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and

acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products

and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be

provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in

such safety-critical applications.

TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are

specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military

specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at

the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.

TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are

designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated

products in automotive applications, TI will not be responsible for any failure to meet such requirements.

Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products Applications

Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive

Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications

Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers

DLP®Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps

DSP dsp.ti.com Energy and Lighting www.ti.com/energy

Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial

Interface interface.ti.com Medical www.ti.com/medical

Logic logic.ti.com Security www.ti.com/security

Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Mobile Processors www.ti.com/omap

Wireless Connectivity www.ti.com/wirelessconnectivity

TI E2E Community Home Page e2e.ti.com

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265