M41T11 512 bit (64 bit x8) Serial Access TIMEKEEPER(R) SRAM FEATURES SUMMARY 2.0 TO 5.5V CLOCK OPERATING VOLTAGE COUNTERS FOR SECONDS, MINUTES, HOURS, DAY, DATE, MONTH, YEARS AND CENTURY YEAR 2000 COMPLIANT SOFTWARE CLOCK CALIBRATION AUTOMATIC SWITCH-OVER AND DESELECT CIRCUITRY I2C BUS COMPATIBLE 56 BYTES of GENERAL PURPOSE RAM ULTRA-LOW BATTERY SUPPLY CURRENT OF 1A LOW OPERATING CURRENT OF 300A BATTERY OR SUPER-CAP BACK-UP BATTERY BACK-UP NOT RECOMMENDED FOR 3.0V APPLICATIONS (CAPACITOR BACK-UP ONLY) OPERATING TEMPERATURE OF -40 TO 85C AUTOMATIC LEAP YEAR COMPENSATION SPECIAL SOFTWARE PROGRAMMABLE OUTPUT PACKAGING INCLUDES a 28-LEAD SOIC and SNAPHAT(R) TOP (to be ordered separately; 3.3V to 5.0V supply voltage only) December 2004 Figure 1. 8-pin SOIC Package 8 1 SO8 (M) Figure 2. 28-pin SOIC Package SNAPHAT (SH) Battery & Crystal 28 1 SOH28 (MH) 1/24 M41T11 TABLE OF CONTENTS FEATURES SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Figure 1. 8-pin SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Figure 2. 28-pin SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SUMMARY DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Figure 3. Table 1. Figure 4. Figure 5. Figure 6. Logic Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Signal Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-pin SOIC Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-pin SOIC Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... .....4 .....4 .....5 .....5 .....5 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2-Wire Bus Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Bus not busy.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Start data transfer.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Stop data transfer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Data valid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Acknowledge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Figure 7. Serial Bus Data Transfer Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Figure 8. Acknowledgement Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Figure 9. Bus Timing Requirements Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Table 2. AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 READ Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 10.Slave Address Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 11.READ Mode Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 12.Alternate READ Mode Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 WRITE Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Data Retention Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Figure 13.WRITE Mode Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 CLOCK OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Table 3. Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Clock Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Output Driver Pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Preferred Initial Power-on Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Figure 14.Crystal Accuracy Across Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Figure 15.Clock Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 MAXIMUM RATING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Table 4. Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 DC AND AC PARAMETERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Table 5. Operating and AC Measurement Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2/24 M41T11 Figure 16.AC Testing Input/Output Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Table 6. Capacitance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Table 7. DC Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Table 8. Crystal Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 17.Power Down/Up Mode AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Table 9. Power Down/Up AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Table 10. Power Down/Up Trip Points DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 PACKAGE MECHANICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 18.SO8 - 8-lead Plastic Small Outline Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Table 11. SO8 - 8-lead Plastic Small Outline Package Mechanical Data. . . . . . . . . . . . . . . . . . . . 18 Figure 19.SOH28 - 28-lead Plastic Small Outline, Battery SNAPHAT Package Outline . . . . . . . . 19 Table 12. SOH28 - 28-lead Plastic Small Outline, Battery SNAPHAT Package Mech. Data . . . . . 19 Figure 20.SH - 4-pin SNAPHAT Housing for 48mAh Battery & Crystal Package Outline . . . . . . . 20 Table 13. SH - 4-pin SNAPHAT Housing for 48mAh Battery & Crystal, Package Mech. Data. . . . 20 Figure 21.SH - 4-pin SNAPHAT Housing for 120mAh Battery & Crystal, Package Outline . . . . . . 21 Table 14. SH - 4-pin SNAPHAT Housing for 120mAh Battery & Crystal, Package Mech. Data. . . 21 PART NUMBERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Table 15. Ordering Information Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Table 16. SNAPHAT Battery Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 REVISION HISTORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Table 17. Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3/24 M41T11 SUMMARY DESCRIPTION The M41T11 TIMEKEEPER (R) RAM is a low power 512-bit, static CMOS RAM organized as 64 words by 8 bits. A built-in 32.768kHz oscillator (external crystal controlled) and the first 8 bytes of the RAM are used for the clock/calendar function and are configured in binary coded decimal (BCD) format. Addresses and data are transferred serially via a two-line bi-directional bus. The built-in address register is incremented automatically after each write or read data byte. The M41T11 clock has a built-in power sense circuit which detects power failures and automatically switches to the battery supply during power failures. The energy needed to sustain the RAM and clock operations can be supplied from a small lithium coin cell. Typical data retention time is in excess of 5 years with a 50mA/h 3V lithium cell. The M41T11 is supplied in 8 lead Plastic Small Outline package or 28 lead SNAPHAT(R) package. The 28-pin, 330mil SOIC provides sockets with gold plated contacts at both ends for direct connection to a separate SNAPHAT housing containing the battery and crystal. The unique design allows the SNAPHAT battery package to be mounted on top of the SOIC package after the completion of the surface mount process. Insertion of the SNAPHAT housing after reflow prevents potential battery and crystal damage due to the high temperatures required for device surfacemounting. The SNAPHAT housing is keyed to prevent reverse insertion. The SOIC and battery/crystal packages are shipped separately in plastic antistatic tubes or in Tape & Reel form. For the 28-lead SOIC, the battery/crystal package (i.e. SNAPHAT) part number is "M4Txx-BR12SH" (see Table 16., page 22). Caution: Do not place the SNAPHAT battery/crystal package "M4Txx-BR12SH" in conductive foam since this will drain the lithium button-cell battery. Figure 3. Logic Diagram Table 1. Signal Names VCC VBAT OSCO OSCI SCL M41T11 Oscillator Input OCSO Oscillator Output FT/OUT Frequency Test / Output Driver (Open drain) SDA SDA Serial Data Address Input / Output FT/OUT SCL Serial Clock VBAT Battery Supply Voltage VCC Supply Voltage VSS Ground VSS AI01000 4/24 OSCI M41T11 Figure 4. 8-pin SOIC Connections Figure 5. 28-pin SOIC Connections NC NC NC NC NC NC NC NC NC NC NC NC NC VSS M41T11 OSCI OSCO VBAT VSS 8 7 6 5 1 2 3 4 VCC FT/OUT SCL SDA AI01001 VCC NC FT/OUT NC NC NC NC NC SCL NC NC NC SDA NC 28 1 2 27 3 26 4 25 5 24 6 23 7 22 M41T11 8 21 9 20 10 19 11 18 12 17 13 16 14 15 AI03606 Figure 6. Block Diagram 1 Hz OSCI OSCILLATOR 32.768 kHz DIVIDER SECONDS MINUTES CENTURY/HOURS OSCO DAY FT/OUT VCC VSS VBAT SCL SDA DATE VOLTAGE SENSE and SWITCH CIRCUITRY SERIAL BUS INTERFACE MONTH CONTROL LOGIC YEAR CONTROL RAM (56 x 8) ADDRESS REGISTER AI02566 5/24 M41T11 OPERATION The M41T11 clock operates as a slave device on the serial bus. Access is obtained by implementing a start condition followed by the correct slave address (D0h). The 64 bytes contained in the device can then be accessed sequentially in the following order: 1. Seconds Register 2. Minutes Register 3. Century/Hours Register 4. Day Register 5. Date Register 6. Month Register 7. Years Register 8. Control Register 9 to 64.RAM The M41T11 clock continually monitors VCC for an out of tolerance condition. Should VCC fall below VSO, the device terminates an access in progress and resets the device address counter. Inputs to the device will not be recognized at this time to prevent erroneous data from being written to the device from an out of tolerance system. When VCC falls below VSO, the device automatically switches over to the battery and powers down into an ultra low current mode of operation to conserve battery life. Upon power-up, the device switches from battery to VCC at VSO and recognizes inputs. 2-Wire Bus Characteristics This bus is intended for communication between different ICs. It consists of two lines: one bi-directional for data signals (SDA) and one for clock signals (SCL). Both the SDA and the SCL lines must be connected to a positive supply voltage via a pull-up resistor. The following protocol has been defined: - Data transfer may be initiated only when the bus is not busy. - During data transfer, the data line must remain stable whenever the clock line is High. - Changes in the data line while the clock line is High will be interpreted as control signals. Accordingly, the following bus conditions have been defined: 6/24 Bus not busy. Both data and clock lines remain High. Start data transfer. A change in the state of the data line, from High to Low, while the clock is High, defines the START condition. Stop data transfer. A change in the state of the data line, from Low to High, while the clock is High, defines the STOP condition. Data valid. The state of the data line represents valid data when after a start condition, the data line is stable for the duration of the High period of the clock signal. The data on the line may be changed during the Low period of the clock signal. There is one clock pulse per bit of data. Each data transfer is initiated with a start condition and terminated with a stop condition. The number of data bytes transferred between the start and stop conditions is not limited. The information is transmitted byte-wide and each receiver acknowledges with a ninth bit. By definition, a device that gives out a message is called "transmitter", the receiving device that gets the message is called "receiver". The device that controls the message is called "master". The devices that are controlled by the master are called "slaves". Acknowledge. Each byte of eight bits is followed by one Acknowledge Bit. This Acknowledge Bit is a low level put on the bus by the receiver, whereas the master generates an extra acknowledge related clock pulse. A slave receiver which is addressed is obliged to generate an acknowledge after the reception of each byte. Also, a master receiver must generate an acknowledge after the reception of each byte that has been clocked out of the slave transmitter. The device that acknowledges has to pull down the SDA line during the acknowledge clock pulse in such a way that the SDA line is a stable Low during the High period of the acknowledge related clock pulse. Of course, setup and hold times must be taken into account. A master receiver must signal an end-of-data to the slave transmitter by not generating an acknowledge on the last byte that has been clocked out of the slave. In this case, the transmitter must leave the data line High to enable the master to generate the STOP condition. M41T11 Figure 7. Serial Bus Data Transfer Sequence DATA LINE STABLE DATA VALID CLOCK DATA START CONDITION CHANGE OF DATA ALLOWED STOP CONDITION AI00587 Figure 8. Acknowledgement Sequence CLOCK PULSE FOR ACKNOWLEDGEMENT START SCLK FROM MASTER DATA OUTPUT BY TRANSMITTER 1 MSB 2 8 9 LSB DATA OUTPUT BY RECEIVER AI00601 7/24 M41T11 Figure 9. Bus Timing Requirements Sequence SDA tBUF tHD:STA tHD:STA tF tR SCL tHIGH P S tLOW tSU:DAT tHD:DAT tSU:STA tSU:STO SR P AI00589 Note: P = STOP and S = START Table 2. AC Characteristics Parameter(1) Symbol Min Max Unit 0 100 kHz fSCL SCL Clock Frequency tLOW Clock Low Period 4.7 s tHIGH Clock High Period 4 s tR SDA and SCL Rise Time 1 s tF SDA and SCL Fall Time 300 ns tHD:STA START Condition Hold Time (after this period the first clock pulse is generated) tSU:STA 4 s START Condition Setup Time (only relevant for a repeated start condition) 4.7 s tSU:DAT Data Setup Time 250 ns tHD:DAT(1) Data Hold Time 0 s STOP Condition Setup Time 4.7 s Time the bus must be free before a new transmission can start 4.7 s tSU:STO tBUF Note: 1. Valid for Ambient Operating Temperature: TA = -40 to 85C; VCC = 2.0 to 5.5V (except where noted). 2. Transmitter must internally provide a hold time to bridge the undefined region (300ns max.) of the falling edge of SCL. 8/24 M41T11 READ Mode In this mode, the master reads the M41T11 slave after setting the slave address (see Figure 10). Following the write Mode Control Bit (R/W = 0) and the Acknowledge Bit, the word address An is written to the on-chip address pointer. Next the START condition and slave address are repeated, followed by the READ Mode Control Bit (R/W = 1). At this point, the master transmitter becomes the master receiver. The data byte which was addressed will be transmitted and the master receiver will send an Acknowledge Bit to the slave transmitter. The address pointer is only incremented on reception of an Acknowledge Bit. The M41T11 slave transmitter will now place the data byte at address An + 1 on the bus. The master receiver reads and acknowledges the new byte and the address pointer is incremented to An + 2. This cycle of reading consecutive addresses will continue until the master receiver sends a STOP condition to the slave transmitter. An alternate READ mode may also be implemented, whereby the master reads the M41T11 slave without first writing to the (volatile) address pointer. The first address that is read is the last one stored in the pointer (see Figure 12., page 10). Figure 10. Slave Address Location R/W START A 1 LSB MSB SLAVE ADDRESS 1 0 1 0 0 0 AI00602 R/W START SLAVE ADDRESS ACK DATA n+1 ACK DATA n ACK BUS ACTIVITY: S ACK WORD ADDRESS (An) STOP SLAVE ADDRESS DATA n+X P NO ACK S R/W SDA LINE ACK BUS ACTIVITY: MASTER START Figure 11. READ Mode Sequence AI00899 9/24 M41T11 STOP SLAVE ADDRESS P NO ACK BUS ACTIVITY: DATA n+X ACK DATA n+1 ACK DATA n ACK S ACK SDA LINE R/W BUS ACTIVITY: MASTER START Figure 12. Alternate READ Mode Sequence AI00895 WRITE Mode In this mode the master transmitter transmits to the M41T11 slave receiver. Bus protocol is shown in Figure 10. Following the START condition and slave address, a logic '0' (R/W = 0) is placed on the bus and indicates to the addressed device that word address An will follow and is to be written to the on-chip address pointer. The data word to be written to the memory is strobed in next and the internal address pointer is incremented to the next memory location within the RAM on the reception of an acknowledge clock. The M41T11 slave receiver will send an acknowledge clock to the mas- ter transmitter after it has received the slave address and again after it has received the word address and each data byte (see Figure 9., page 8). Data Retention Mode With valid VCC applied, the M41T11 can be accessed as described above with read or write cycles. Should the supply voltage decay, the M41T11 will automatically deselect, write protecting itself when VCC falls (see Figure 17). SLAVE ADDRESS 10/24 STOP DATA n+X P ACK DATA n+1 ACK BUS ACTIVITY: DATA n ACK WORD ADDRESS (An) ACK S R/W SDA LINE ACK BUS ACTIVITY: MASTER START Figure 13. WRITE Mode Sequence AI00591 M41T11 CLOCK OPERATION The eight byte clock register (see Table 3) is used to both set the clock and to read the date and time from the clock, in a binary coded decimal format. Seconds, Minutes, and Hours are contained within the first three registers. Bits D6 and D7 of clock register 2 (Hours Register) contain the CENTURY ENABLE Bit (CEB) and the CENTURY Bit (CB). Setting CEB to a '1' will cause CB to toggle, either from '0' to '1' or from '1' to '0' at the turn of the century (depending upon its initial state). If CEB is set to a '0', CB will not toggle. Bits D0 through D2 of register 3 contain the Day (day of week). Registers 4, 5 and 6 contain the Date (day of month), Month and Years. The final register is the Control Register (this is described in the Clock Calibration section). Bit D7 of register 0 contains the STOP Bit (ST). Setting this bit to a '1' will cause the oscillator to stop. If the device is expected to spend a significant amount of time on the shelf, the oscillator may be stopped to reduce current drain. When reset to a '0' the oscillator restarts within one second. Note: In order to guarantee oscillator start-up after the initial power-up, set the ST Bit to a '1,' then reset this bit to a '0.' This sequence enables a "kick start" circuit which aids the oscillator start-up during worst case conditions of voltage and temperature. The seven Clock Registers may be read one byte at a time, or in a sequential block. The Control Register (Address location 7) may be accessed independently. Provision has been made to assure that a clock update does not occur while any of the seven clock addresses are being read. If a clock address is being read, an update of the clock registers will be delayed by 250ms to allow the read to be completed before the update occurs. This will prevent a transition of data during the read. Note: This 250ms delay affects only the clock register update and does not alter the actual clock time. Table 3. Register Map Data Address D7 D6 D5 D4 D3 D2 D1 D0 Function/Range BCD Format 0 ST 10 Seconds Seconds Seconds 00-59 1 X 10 Minutes Minutes Minutes 00-59 2 CEB (1) CB Hours Century/Hours 0-1/00-23 3 X X Day 01-07 4 X X Date Date 01-31 5 X X Month Month 01-12 Years Year 00-99 6 7 10 Hours X 10 Date X 10 Years OUT FT Keys: S = SIGN Bit FT = FREQUENCY TEST Bit ST = STOP Bit OUT = Output level X S 10 M. X Day Calibration Control X = Don't care CEB = Century Enable Bit CB = Century Bit Note: 1. When CEB is set to '1', CB will toggle from '0' to '1' or from '1' to '0' every 100 years (dependent upon the initial value set). When CEB is set to '0', CB will not toggle. 11/24 M41T11 Clock Calibration The M41T11 is driven by a quartz controlled oscillator with a nominal frequency of 32,768Hz. The devices are tested not to exceed 35 ppm (parts per million) oscillator frequency error at 25C, which equates to about 1.53 minutes per month. With the calibration bits properly set, the accuracy of each M41T11 improves to better than 2 ppm at 25C. The oscillation rate of any crystal changes with temperature (see Figure 14., page 13). Most clock chips compensate for crystal frequency and temperature shift error with cumbersome trim capacitors. The M41T11 design, however, employs periodic counter correction. The calibration circuit adds or subtracts counts from the oscillator divider circuit at the divide by 256 stage, as shown in Figure 15., page 13. The number of times pulses are blanked (subtracted, negative calibration) or split (added, positive calibration) depends upon the value loaded into the five-bit Calibration byte found in the Control Register. Adding counts speeds the clock up, subtracting counts slows the clock down. The Calibration byte occupies the five lower order bits (D4-D0) in the Control register (Addr 7). This byte can be set to represent any value between 0 and 31 in binary form. Bit D5 is a Sign Bit; '1' indicates positive calibration, '0' indicates negative calibration. Calibration occurs within a 64minute cycle. The first 62 minutes in the cycle may, once per minute, have one second either shortened by 128 or lengthened by 256 oscillator cycles. If a binary '1' is loaded into the register, only the first 2 minutes in the 64 minute cycle will be modified; if a binary 6 is loaded, the first 12 will be affected, and so on. Therefore, each calibration step has the effect of adding 512 or subtracting 256 oscillator cycles for every 125,829,120 actual oscillator cycles, that is +4.068 or -2.034 ppm of adjustment per calibration step in the calibration register. Assuming that the oscillator is in fact running at exactly 32,768Hz, each of the 31 increments in the Calibration byte would represent +10.7 or -5.35 seconds per 12/24 month which corresponds to a total range of +5.5 or -2.75 minutes per month. Two methods are available for ascertaining how much calibration a given M41T11 may require. The first involves simply setting the clock, letting it run for a month and comparing it to a known accurate reference (like WWV broadcasts). While that may seem crude, it allows the designer to give the end user the ability to calibrate his clock as his environment may require, even after the final product is packaged in a non-user serviceable enclosure. All the designer has to do is provide a simple utility that accessed the Calibration byte. The second approach is better suited to a manufacturing environment, and involves the use of some test equipment. When the Frequency Test (FT) Bit, the seventh-most significant bit in the Control Register, is set to a '1', and the oscillator is running at 32,768Hz, the FT/OUT pin of the device will toggle at 512Hz. Any deviation from 512Hz indicates the degree and direction of oscillator frequency shift at the test temperature. For example, a reading of 512.01024Hz would indicate a +20 ppm oscillator frequency error, requiring a -10(XX001010) to be loaded into the Calibration Byte for correction. Note that setting or changing the Calibration Byte does not affect the Frequency test output frequency. Output Driver Pin When the FT Bit is not set, the FT/OUT pin becomes an output driver that reflects the contents of D7 of the control register. In other words, when D6 of location 7 is a zero and D7 of location 7 is a zero and then the FT/OUT pin will be driven low. Note: The FT/OUT pin is open drain which requires an external pull-up resistor. Preferred Initial Power-on Defaults Upon initial application of power to the device, the FT Bit will be set to a '0' and the OUT Bit will be set to a '1'. All other Register bits will initially power-on in a random state. M41T11 Figure 14. Crystal Accuracy Across Temperature Frequency (ppm) 20 0 -20 -40 -60 -80 F = K x (T -T )2 O F -100 K = -0.036 ppm/C2 0.006 ppm/C2 -120 TO = 25C 5C -140 -160 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 Temperature C AI00999b Figure 15. Clock Calibration NORMAL POSITIVE CALIBRATION NEGATIVE CALIBRATION AI00594B 13/24 M41T11 MAXIMUM RATING Stressing the device above the rating listed in the "Absolute Maximum Ratings" table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. Table 4. Absolute Maximum Ratings Symbol TA TSTG TSLD (1) Parameter Ambient Operating Temperature Storage Temperature (VCC Off, Oscillator Off Lead Solder Temperature for 10 seconds Value Unit -40 to 85 C SNAPHAT(R) -40 to 85 SOIC -55 to 125 C 260 C VIO Input or Output Voltages -0.3 to 7 V VCC Supply Voltage -0.3 to 7 V IO Output Current 20 mA PD Power Dissipation 0.25 W Note: 1. For SO package, standard (SnPb) lead finish: Reflow at peak temperature of 225C (total thermal budget not to exceed 180C for between 90 to 150 seconds). 2. For SO package, Lead-free (Pb-free) lead finish: Reflow at peak temperature of 260C (total thermal budget not to exceed 245C for greater than 30 seconds). CAUTION: Negative undershoots below -0.3V are not allowed on any pin while in the Battery Back-up mode. CAUTION: Do NOT wave solder SOIC to avoid damaging SNAPHAT sockets. 14/24 M41T11 DC AND AC PARAMETERS This section summarizes the operating and measurement conditions, as well as the DC and AC characteristics of the device. The parameters in the following DC and AC Characteristic tables are derived from tests performed under the Measure- ment Conditions listed in the relevant tables. Designers should check that the operating conditions in their projects match the measurement conditions when using the quoted parameters. Table 5. Operating and AC Measurement Conditions Parameter M41T11 Unit 2.0 to 5.5(1) V -40 to 85 C Load Capacitance (CL) 100 pF Input Rise and Fall Times 50 ns Input Pulse Voltages 0.2VCC to 0.8VCC V Input and Output Timing Ref. Voltages 0.3VCC to 0.7VCC V Supply Voltage (VCC) Ambient Operating Temperature (TA) Note: Output Hi-Z is defined as the point where data is no longer driven. 1. Supply Voltage for SOH28 is 3.3V to 5.5V. Figure 16. AC Testing Input/Output Waveform 0.8VCC 0.7VCC 0.3VCC 0.2VCC AI02568 Table 6. Capacitance Symbol CIN COUT(3) tLP Parameter(1,2) Max Unit Input Capacitance (SCL) 7 pF Output Capacitance (SDA, FT/OUT) 10 pF 1000 ns Low-pass filter input time constant (SDA and SCL) Min 250 Note: 1. Effective capacitance measured with power supply at 5V; sampled only, not 100% tested. 2. At 25C, f = 1MHz. 3. Outputs deselected. 15/24 M41T11 Table 7. DC Characteristics Symbol Test Condition(1) Parameter Min Typ Max Unit 0V VIN VCC 1 A 0V VOUT VCC 1 A Switch Frequency = 100kHz 300 A SCL, SDA = VCC - 0.3V 70 A ILI Input Leakage Current ILO Output Leakage Current ICC1 Supply Current ICC2 Supply Current (Standby) VIL Input Low Voltage -0.3 0.3VCC V VIH Input High Voltage 0.7VCC VCC + 0.5 V VOL Output Low Voltage IOL = 3mA 0.4 V FT/OUT 5.5 V 3 3.5(4) V 0.8 1 A Max Unit Pull-up Supply Voltage (Open Drain) VBAT(2) Battery Supply Voltage IBAT Battery Supply Current Note: 1. 2. 3. 4. 2.5(3) TA = 25C, VCC = 0V, Oscillator ON, VBAT = 3V Valid for Ambient Operating Temperature: TA = -40 to 85C; VCC = 2.0 to 5.5V (except where noted). STMicroelectronics recommends the RAYOVAC BR1225 or BR1632 (or equivalent) as the battery supply. After switchover (VSO), VBAT(min) can be 2.0V for crystal with RS = 40K. For rechargeable back-up, VBAT(max) may be considered VCC. Table 8. Crystal Electrical Characteristics Symbol Parameter(1,2,3) fO Resonant Frequency RS Series Resistance CL Load Capacitance Min Typ 32.768 kHz 60 12.5 k pF Note: 1. These values are externally supplied if using the SO8 package. STMicroelectronics recommends the KDS DT-38: 1TA/ 1TC252E127, Tuning Fork Type (thru-hole) or the DMX-26S: 1TJS125FH2A212, (SMD) quartz crystal for industrial temperature operations. KDS can be contacted at kouhou@kdsj.co.jp or http://www.kdsj.co.jp for further information on this crystal type. 2. Load capacitors are integrated within the M41T11. Circuit board layout considerations for the 32.768kHz crystal of minimum trace lengths and isolation from RF generating signals should be taken into account. 3. All SNAPHAT (R) battery/crystal tops meet these specifications. 16/24 M41T11 Figure 17. Power Down/Up Mode AC Waveforms VCC VSO tPD tREC SDA SCL DON'T CARE AI00596 Table 9. Power Down/Up AC Characteristics Symbol Parameter(1) Min Max Unit tPD(2) SCL and SDA at VIH before Power Down 0 ns tREC SCL and SDA at VIH after Power Up 10 s Note: 1. Valid for Ambient Operating Temperature: TA = -40 to 85C; VCC = 2.0 to 5.5V (except where noted). 2. VCC fall time should not exceed 5mV/s. Table 10. Power Down/Up Trip Points DC Characteristics Symbol VSO(4) Parameter(1,2) Battery Back-up Switchover Voltage Min Typ Max(3) Unit VBAT - 0.80 VBAT - 0.50 VBAT - 0.30 V Note: 1. Valid for Ambient Operating Temperature: TA = -40 to 85C; VCC = 2.0 to 5.5V (except where noted). 2. All voltages referenced to VSS. 3. In 3.3V application, if initial battery voltage is 3.4V, it may be necessary to reduce battery voltage (i.e., through wave soldering the battery) in order to avoid inadvertent switchover/deselection for VCC - 10% operation. 4. Switch-over and deselect point. 17/24 M41T11 PACKAGE MECHANICAL INFORMATION Figure 18. SO8 - 8-lead Plastic Small Outline Package Outline h x 45 A C B CP e D N E H 1 A1 L SO-a Note: Drawing is not to scale. Table 11. SO8 - 8-lead Plastic Small Outline Package Mechanical Data mm inches Symb Typ Min Max A 1.35 A1 Min Max 1.75 0.053 0.069 0.10 0.25 0.004 0.010 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 4.80 5.00 0.189 0.197 E 3.80 4.00 0.150 0.157 - - - - H 5.80 6.20 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.40 0.90 0.016 0.035 0 8 0 8 N 8 e CP 18/24 1.27 Typ 0.050 8 0.10 0.004 M41T11 Figure 19. SOH28 - 28-lead Plastic Small Outline, Battery SNAPHAT Package Outline A2 A C B eB e CP D N E H A1 L 1 SOH-A Note: Drawing is not to scale. Table 12. SOH28 - 28-lead Plastic Small Outline, Battery SNAPHAT Package Mech. Data mm inches Symb Typ Min A Max Typ Min 3.05 Max 0.120 A1 0.05 0.36 0.002 0.014 A2 2.34 2.69 0.092 0.106 B 0.36 0.51 0.014 0.020 C 0.15 0.32 0.006 0.012 D 17.71 18.49 0.697 0.728 E 8.23 8.89 0.324 0.350 - - - - eB 3.20 3.61 0.126 0.142 H 11.51 12.70 0.453 0.500 L 0.41 1.27 0.016 0.050 0 8 0 8 N 28 e CP 1.27 0.050 28 0.10 0.004 19/24 M41T11 Figure 20. SH - 4-pin SNAPHAT Housing for 48mAh Battery & Crystal Package Outline A1 eA A2 A3 A B L eB D E SHTK-A Note: Drawing is not to scale. Table 13. SH - 4-pin SNAPHAT Housing for 48mAh Battery & Crystal, Package Mech. Data mm inches Symb Typ Min A Typ Min 9.78 Max 0.385 A1 6.73 7.24 0.265 0.285 A2 6.48 6.99 0.255 0.275 A3 20/24 Max 0.38 0.015 B 0.46 0.56 0.018 0.022 D 21.21 21.84 0.835 0.860 E 14.22 14.99 0.560 0.590 eA 15.55 15.95 0.612 0.628 eB 3.20 3.61 0.126 0.142 L 2.03 2.29 0.080 0.090 M41T11 Figure 21. SH - 4-pin SNAPHAT Housing for 120mAh Battery & Crystal, Package Outline A1 eA A2 A3 A B L eB D E SHTK-B Note: Drawing is not to scale. Table 14. SH - 4-pin SNAPHAT Housing for 120mAh Battery & Crystal, Package Mech. Data mm inches Symb Typ Min A Max Typ Min 10.54 Max 0.415 A1 8.00 8.51 0.315 0.335 A2 7.24 8.00 0.285 0.315 A3 0.38 0.015 B 0.46 0.56 0.018 0.022 D 21.21 21.84 0.835 0.860 E 17.27 18.03 0.680 0.710 eA 15.55 15.95 0.612 0.628 eB 3.20 3.61 0.126 0.142 L 2.03 2.29 0.080 0.090 21/24 M41T11 PART NUMBERING Table 15. Ordering Information Scheme Example: M41T 11 M 6 E Device Type M41T Supply Voltage 11 = VCC = 2.0 to 5.5V(1) Package M = SO8 (150mil width) MH(2) = SOH28 Temperature Range 6 = -40 to 85C Shipping Method For SO8: blank = Tubes (Not for New Design - Use E) E = Lead-free Package (ECO PACK(R)), Tubes F = Lead-free Package (ECO PACK(R)), Tape & Reel TR = Tape & Reel (Not for New Design - Use F) For SOH28: blank = Tubes (Not for New Design - Use E) E = Lead-free Package (ECO PACK(R)), Tubes F = Lead-free Package (ECO PACK(R)), Tape & Reel TR = Tape & Reel (Not for New Design - Use F) Note: 1. SOH28 Supply Voltage is 3.3V to 5.5V. 2. The SOIC package (SOH28) requires the SNAPHAT(R) battery package which is ordered separately under the part number "M4TxxBR12SHx" in plastic tube or "M4Txx-BR12SHxTR" in Tape & Reel form (see Table 16). Caution: Do not place the SNAPHAT battery package "M4TXX-BR12SH" in conductive foam as it will drain the lithium button-cell battery. For other options, or for more information on any aspect of this device, please contact the ST Sales Office nearest you. Table 16. SNAPHAT Battery Table Part Number 22/24 Description Package M4T28-BR12SH Lithium Battery (48mAh) SNAPHAT SH M4T32-BR12SH Lithium Battery (120mAh) SNAPHAT SH M41T11 REVISION HISTORY Table 17. Document Revision History Date Version Revision Details March 1999 1.0 First Issue 12/23/99 1.1 SOH28 package added 07/25/00 1.2 Crystal Electrical Characteristics: RS Max changed (Table 8) 12/12/00 1.3 Edit VSO (Table 10) 01/24/01 2.0 Reformatted 2/27/01 3.0 Document Status changed 07/17/01 3.1 Change to DC and AC Characteristics (Tables 7, 2); added temp/voltage info. to tables (Table 6, 7, 8, 2, 9, 10); added SNAPHAT Battery table (Table 16). 11/27/01 3.2 Features, (page 1); DC Characteristics (Table 7); Crystal Electrical (Table 8); Power Down/ Up Trip Points (Table 10) changes; add table footnotes (Table 5, 10, 15) 01/21/02 3.3 Fix table footnotes (Table 7, 8) 05/01/02 3.4 Modify reflow time and temperature footnote (Table 4) 07/03/02 3.5 Modify "Clock Operation" text, Crystal Electrical Characteristics table footnote (Table 8) 11/07/02 3.6 Correct figure name (Figure 1) 15-Jun-04 4.0 Reformatted; added Lead-free information; updated characteristics (Figure 14; Table 4, 7, 15) 14-Dec-04 5.0 Correct footnote (Table 8) M41T11, 41T11, T11, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, NVRAM, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, TIMEKEEPER, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, Access, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, SRAM, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, Leap year, Leap year, Leap year, Leap year, Leap year, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, software, clock,clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, clock, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Industrial, Industrial, Industrial, Industrial, Industrial, Industrial, Industrial, Industrial, Industrial, Industrial, Industrial, Industrial, Industrial, Industrial, Industrial, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Temperature, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Write Protect, Power-fail, Power-fail, Power-fail, Power-fail, Powerfail, Power-fail, Power-fail, Power-fail, Power-fail, Power-fail, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Back-up, Back-up, Back-up, Back-up, Back-up, Back-up, Back-up, Back-up, Back-up, Back-up, Back-up, Back-up, Back-up, Back-up, Back-up, Back-up, Back-up, Back-up, Back-up, Back-up, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 2V, 2V, 2V, 2V, 2V, 2V, 2V, 2V, 2V, 2V, 2V, 2V, 2V, 2V, 2V, 2V, 2V, 2V, 2V, 2V, 2V, 2V, 2V, 2V, 2V 23/24 M41T11 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners (c) 2004 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 24/24