©2010 Fairchild Semiconductor Corporation
www.fairchildsemi.com
Rev. 1.0.3
Features
Internall y Freq uency Compensated for Unit y Gai n
Large DC Voltage Gain: 100dB
Wide Power Suppl y Range:
LM258/LM258A, LM358/LM358A: 3V~32V (or ±1.5V
~ 16V)
LM2904 : 3V~26V (or ±1.5V ~ 13V)
Input Common Mode Voltage Range Includes Ground
Large Output Voltage Swing: 0V DC to Vcc -1.5V DC
Power Drain Suitable for Battery Operation.
Description
The LM2904,LM358/LM358A , LM258/LM258A consist of
two independent, hi gh gain, internally frequency
compensated operational amplifiers which were designed
specifically to operate from a single power supply over a
wide range of voltage. Operation from split power supplies
is also possible and the low power supply current drain is
independent of the magnitude of the power supply voltage.
Application areas include transducer amplifier, DC gain
blocks and all the conventional OP-AMP circuits which now
can be easily implemente d in single po wer supply systems.
8-DIP
8-SOP
1
1
Internal Block Diagram
-
+
+
-
1
2
3
45
6
7
8VCC
OUT2
IN2 (-)
IN2 (+)
OUT1
IN1 (-)
IN1 (+)
GND
LM2904,LM358/LM358A,LM258/
LM258A
Dual Operational Amplifier
LM2904,LM358/LM358A,LM258/LM258A
2
Schematic Diagram
(One section only)
Absolute Maximum Ratings
Parameter Symbol LM258/LM258A LM358/LM358A LM2904 Unit
Supply Voltage VCC ±16 or 32 ±16 or 32 ±13 or 26 V
Differential Input Voltage VI(DIFF) 32 32 26 V
Input Voltage VI-0.3 to +32 -0.3 to +32 -0.3 to +26 V
Output Short Circuit to GND
VCC15V, TA = 25°C(One Amp) - Continuous Continuous Continuous -
Operating Temperature Range TOPR -25 ~ +85 0 ~ +70 -40 ~ +85 °C
Maximun Junc tion Tem pe ra tu re TJ(MAX) +150 +150 +150 °C
Storage Temperature Range TSTG -65 ~ +150 -65 ~ +150 -65 ~ +150 °C
Q8
Q7
Q6
Q5
Q4
Q3
Q2
Q1
Q9
Q10
Q11
Q12
Q14
Q15
Q16
Q18
Q19
Q20
R2
Q21
C1 R1
GND
OUTPUT
IN(+)
IN(-)
VCC
Q13
Q17
LM2904,LM358/LM358A,LM258/LM258A
3
Electrical Characteristics
(VCC = 5.0V, VEE = GND, TA = 25°C, unless otherwise specified)
Note:
1. This parameter, altho ugh guaranteed, is not 100% tested in production.
Parameter Symbol Conditions LM258 LM358 LM2904 Unit
Min. Typ. Max. Min. Typ. Max. Min. Typ. Max.
Input Offset
Voltage VIO
VCM = 0V to VCC
-1.5V
VO(P) = 1.4V,
RS = 0Ω
- 2.9 5.0 - 2.9 7.0 - 2.9 7.0 mV
Input Offset
Current IIO - - 330- 550- 550nA
Input Bias
Current IBIAS - - 45 150 - 45 250 - 45 250 nA
Input Voltage
Range VI(R) VCC = 30V
(LM2904, VCC=26V) 0-
VCC
-1.5 0-
VCC
-1.5 0-
VCC
-1.5 V
Supply Current ICC
RL = , VCC = 30V
(LM2904, VCC=26V) - 0.8 2.0 - 0.8 2.0 - 0.8 2.0 mA
RL = , VCC = 5V - 0.5 1.2 - 0.5 1.2 - 0.5 1.2 mA
Large Signal
Voltage Gain GVVCC = 15V,
RL= 2kΩ
VO(P) = 1V to 11V 50 100 - 25 100 - 25 100 - V/mV
Output Voltage
Swing
VO(H) VCC=30V
(VCC
=26V for
LM2904)
RL = 2kΩ26 - - 26 - - 22 - - V
RL=
10kΩ27 28 - 27 28 - 23 24 - V
VO(L) VCC = 5V, RL= 10kΩ-520-520 520mV
Common-Mode
Rejection Ratio CMRR - 70 85 - 65 80 - 50 80 - dB
Power Supply
Rejection Ratio PSRR - 65 100 - 65 100 - 50 100 - dB
Channel
Separation CS f = 1kHz to 20kHz
(Note1) - 120 - - 120 - - 120 - dB
Short Circuit to
GND ISC - - 40 60 - 40 60 - 40 60 mA
Output Current
ISOURCE
VI(+) = 1V,
VI(-) = 0V,
VCC = 15V,
VO(P) = 2V
20 30 - 20 30 - 20 30 - mA
ISINK
VI(+) = 0V, VI(-) = 1V,
VCC = 15V,
VO(P) = 2V 10 15 - 10 15 - 10 15 - mA
VI(+) = 0V,VI(-) =1V ,
VCC = 15V,
VO(P) = 200mV 12 100 - 12 100 - - - - μA
Differential
Input Voltage VI(DIFF) ---V
CC --V
CC --V
CC V
LM2904,LM358/LM358A,LM258/LM258A
4
Electrical Characteristics (Continued)
(VCC= 5.0V, VEE = GND, unless otherwise specified)
The following specification apply over the range of -25°C TA +85°C for the LM258; and the 0°C TA +70°C
for the LM358; and the -40°C TA +85°C for the LM2904
Parameter Symbol Conditions LM258 LM358 LM2904 Unit
Min. Typ. Max. Min. Typ. Max. Min. Typ. Max.
Input Offset
Voltage VIO
VCM = 0V to
VCC -1.5V
VO(P) = 1.4V,
RS = 0Ω
- - 7.0 - - 9.0 - - 10.0 mV
Input Offset
Voltage Drift ΔVIO/ΔTRS = 0Ω-7.0 - -7.0 - -7.0-μV/°C
Input Offset
Current IIO - - - 100 - - 150 - 45 200 nA
Input Offset
Current Drift ΔIIO/ΔT- -10--10--10-pA/°C
Input Bias
Current IBIAS - - 40 300 - 40 500 - 40 500 nA
Input Voltage
Range VI(R) VCC = 30V
(LM2904 , VCC = 26V) 0-
VCC
-2.0 0-
VCC
-2.0 0-
VCC
-2.0 V
Large Signal
Voltage Gain GVVCC = 15V,
RL =2.0kΩ
VO(P) = 1V to 11V 25 - - 15 - - 15 - - V/mV
Output Voltage
Swing VO(H)
VCC=30V
(VCC =
26V for
LM2904)
RL = 2kΩ26 - - 26 - - 22 - - V
RL=10kΩ27 28 - 27 28 - 23 24 - V
VO(L) VCC = 5V, RL=10kΩ- 5 20 - 5 20 - 5 20 mV
Output Current
ISOURCE
VI(+) = 1V,
VI(-) = 0V,
VCC = 15V,
VO(P) = 2V
10 30 - 10 30 - 10 30 - mA
ISINK
VI(+) = 0V,
VI(-) = 1V,
VCC = 15V,
VO(P) = 2V
58 - 59 - 59 -mA
Differential
Input Voltage VI(DIFF) ---V
CC --V
CC --V
CC V
LM2904,LM358/LM358A,LM258/LM258A
5
Electrical Characteristics (Continued)
(VCC = 5.0V, VEE = GND, TA = 25°C, unless otherwise specified)
Note:
1. This parameter, altho ugh guaranteed, is not 100% tested in production.
Parameter Symbol Conditions LM258A LM358A Unit
Min. Typ. Max. Min. Typ. Max.
Input Offset Voltage VIO VCM = 0V to VCC -1.5V
VO(P) = 1.4V, RS = 0Ω- 1.0 3.0 - 2.0 3.0 mV
Input Offset Current IIO --215-530nA
Input Bias Curren t IBIAS - - 40 80 - 45 100 nA
Input Voltage Ra ng e VI(R) VCC = 30V 0 - VCC
-1.5 0-
VCC
-1.5 V
Supply Current ICC RL = ,VCC = 30V - 0.8 2.0 - 0.8 2.0 mA
RL = , VCC = 5V - 0.5 1.2 - 0.5 1.2 mA
Large Signal Voltage
Gain GVVCC = 15V, RL= 2kΩ
VO = 1V to 11V 50 100 - 25 100 - V/mV
Output Voltage Swing VOH VCC = 30V RL = 2kΩ26 - - 26 - V
RL =10kΩ27 28 - 27 28 - V
VO(L) VCC = 5V, RL=10kΩ-520-520mV
Common-Mode
Rejection Ratio CMRR - 70 85 - 65 85 - dB
Power Supply
Rejection Ratio PSRR - 65 100 - 65 100 - dB
Channel Separation CS f = 1kHz to 20kHz (Note1) - 120 - - 120 - dB
Short Circuit to GND ISC --4060-4060mA
Output Current
ISOURCE VI(+) = 1V, VI(-) = 0V
VCC = 15V, VO(P) = 2V 20 30 - 20 30 - mA
ISINK
VI(+) = 1V, VI(-) = 0V
VCC = 15V, VO(P) = 2V 10 15 - 10 15 - mA
Vin + = 0V, Vin (-) = 1V
VO(P) = 200mV 12 100 - 12 100 - μA
Differential Input
Voltage VI(DIFF) ---V
CC --V
CC V
LM2904,LM358/LM358A,LM258/LM258A
6
Electrical Characteristics (Continued)
(VCC = 5.0V, VEE = GND, unless otherwise specified)
The following specification apply over th e rang e of -25°C TA +85°C for the LM258A; and the 0°C TA +70°C
for the LM358A
Parameter Symbol Conditions LM258A LM358A Unit
Min. Typ. Max. Min. Typ. Max.
Input Offset Voltage VIO VCM = 0V to VCC -1.5V
VO(P) = 1.4V, RS = 0Ω--4.0--5.0mV
Input Offset Voltage Drift ΔVIO/ΔT- -7.015-7.020μV/°C
Input Offset Current IIO ---30--75nA
Input Offset Current Drift ΔIIO/ΔT - -10200-10300pA/°C
Input Bias Curren t IBIAS - - 40 100 - 40 200 nA
Input Common-Mode
Voltage Range VI(R) VCC = 30V 0 - Vcc
-2.0 0-
Vcc
-2.0 V
Output Voltage Swing VO(H) VCC = 30V RL = 2kΩ26 - - 26 - - V
RL = 10kΩ27 28 - 27 28 - V
VO(L) VCC = 5V, RL=10kΩ-520-520mV
Large Signal Voltage Gain GVVCC = 15V, RL=2.0kΩ
VO(P) = 1V to 11V 25 - - 15 - - V/mV
Output Current ISOURCE VI(+) = 1V, VI(-) = 0V
VCC = 15V, VO(P) = 2V 10 30 - 10 30 - mA
ISINK VI(+) = 1V, VI(-) = 0V
VCC = 15V, VO(P) = 2V 59 - 59 - mA
Differential Input Voltage VI(DIFF) ---V
CC --V
CC V
LM2904,LM358/LM358A,LM258/LM258A
7
Typical Performance Characteristics
Figure 1. Supply Current vs Supply Voltage Figure 2. Voltage Gain vs Supply Voltage
Figure 3. Open Loop Fr equency Response Figure 4. Large Signal Output Swing vs Frequency
Figure 5. Output Characteristics vs Current Sourcing Figure 6. Output Characteristics vs Current Sinking
LM2904,LM358/LM358A,LM258/LM258A
8
Typical Performance Characteristics (Continued)
Figure 7. Input Voltage Range vs Supply Voltage Figure 8. Common-Mode Rejection Ratio
Figure 9. Output Current vs Temperature (Current Limiting) Figure 10. Input Current vs Temperature
Figure 11. Voltage Follower Pulse Response Figure 12. Voltage Follower Pulse Response
(Small Signal)
LM2904,LM358/LM358A,LM258/LM258A
9
Mechanical Dimensions
Package Dimensions in millimeters
6.40
±0.20
3.30
±0.30
0.130
±0.012
3.40
±0.20
0.134
±0.008
#
1
#
4#5
#8
0.252
±0.008
9.20
±0.20
0.79
2.54
0.100
0.031
(
)
0.46
±0.10
0.018
±0.004
0.060
±0.004
1.524
±0.10
0.362
±0.008
9.60
0.378 MAX
5.08
0.200
0.33
0.013
7.62
0~15°
0.300
MAX
MIN
0.25
+0.10
–0.05
0.010
+0.004
–0.002
8-DIP
LM2904,LM358/LM358A,LM258/LM258A
10
Mechanical Dimensions (Continued)
Package Dimensions in millimeters
4.92 ±0.20
0.194 ±0.008
0.41 ±0.10
0.016 ±0.004
1.27
0.050
5.72
0.225
1.55 ±0.20
0.061 ±0.008
0.1~0.25
0.004~0.001
6.00 ±0.30
0.236 ±0.012
3.95 ±0.20
0.156 ±0.008
0.50 ±0.20
0.020 ±0.008
5.13
0.202 MAX
#1
#4 #5
0~8°
#8
0.56
0.022
()
1.80
0.071
MAX0.10
MAX0.004
MAX
MIN
+0.10
-0.05
0.15+0.004
-0.002
0.006
8-SOP
LM2904,LM358/LM358A,LM258/LM258A
11
Ordering Information
Product Number Package Operating Temperature
LM358N 8-DIP 0 ~ +70 °C
LM358AN
LM358M 8-SOP
LM358AM
LM2904N 8-DIP -40 ~ +85°C
LM2904M 8-SOP
LM258N 8-DIP -2 5 ~ +85 °C
LM258AN
LM258M 8-SOP
LM258AM
LM2904,LM358/LM358A,LM258/LM258A
4/6/10 0.0m 001
Stock#DS400005
© 2010 Fairchild Semiconductor Corporation
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES
OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body,
or (b) support or sustain life, and (c) whose failure to
perform when properly used in accordance with
instructions for use provided in the labeling, can be
reasonably expected to result in a significant injury of the
user.
2. A critical co mponent in any component of a life support
device or system whose failure to perform can be
reasonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
www.fairchildsemi.com
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY
PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY
LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER
DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.