Kinetis KV31F 256 KB Flash
120 MHz ARM® Cortex®-M4-Based Microcontroller with FPU
The KV31 MCU family is a highly scalable member of the Kinetis
V Series and provides a high-performance, cost-competitive
motor control solution. Built on the ARM®Cortex®-M4 core
running at 120 MHz, combined with floating point and DSP
capability, it delivers a highly capable platform enabling
customers to build a highly scalable solution portfolio.
Additional features include:
Dual 16-bit ADCs sampling at up to 1.2 MS/s in 12-bit
mode
12 channels of highly flexible motor control timers (PWMs)
across 3 independent time bases
Large RAM block enabling local execution of fast control
loops at full clock speed
Enabled to support Kinetis Motor Suite (KMS), a bundled
hardware and software solution that enables rapid configuration of BLDC and PMSM motor drive
systems
Performance
120 MHz ARM Cortex-M4 core with DSP instructions
delivering 1.25 Dhrystone MIPS per MHz
Memories and memory interfaces
256 KB of embedded flash and 48 KB of RAM
Preprogrammed Kinetis flashloader for one-time, in-
system factory programming
System peripherals
16-channel DMA controller
Independent external and software watchdog monitor
Clocks
One crystal oscillator, two ranges: 32-40 kHz or 3-32
MHz
Three internal oscillators: 32 kHz, 4 MHz, and 48 MHz
Multi-purpose clock generator with PLL and FLL
Security and integrity modules
Hardware CRC module
128-bit unique identification (ID) number per chip
Hardware random-number generator
Flash access control to protect proprietary software
Human-machine interface
Analog modules
Two 16-bit SAR ADCs (1.2 MS/s in 12bit mode)
One 12-bit DAC
Two analog comparators (CMP) with 6- bit DAC
Accurate internal voltage reference
Communication interfaces
Two SPI modules
Three UART modules and one low-power UART
Two I2C modules: Support for up to 1 Mbps
operation
Timers
One 8-channel motor control/general purpose/ PWM
timer
Two 2-channel motor control/general purpose timers
with quadrature decoder functionality
Operating Characteristics
Voltage range (including flash writes): 1.71 to 3.6 V
Temperature range (ambient): -40 to 105°C
Kinetis Motor Suite
Supports Velocity and Position control of BLDC &
PMSM motors
MKV31F256VLL12
MKV31F256VLH12
MKV31F256VLH12P
100 LQFP (LL)
14 x 14 x 1.4 Pitch 0.5
mm
64 LQFP (LH)
10 x 10 x 1.4 Pitch 0.5
mm
Freescale Semiconductor, Inc. KV31P100M120SF8
Data Sheet: Technical Data Rev. 7, 02/2016
© 2014–2016 Freescale Semiconductor, Inc. All rights reserved.
Up to 70 general-purpose I/O (GPIO) Implements Field Orient Control (FOC) using Back
EMF to improve motor efficiency
Utilizes SpinTAC control theory that improves
overall system performance and reliability
Ordering Information
Part Number Memory Number of GPIOs
Flash (KB) SRAM (KB)
MKV31F256VLL12 256 48 70
MKV31F256VLH12 256 48 46
MKV31F256VLH12P 248 48 46
Related Resources
Type Description Resource
Selector
Guide
The Freescale Solution Advisor is a web-based tool that features
interactive application wizards and a dynamic product selector
Product Selector
Product Brief The Product Brief contains concise overview/summary information to
enable quick evaluation of a device for design suitability.
KV30FKV31FPB
Reference
Manual
The Reference Manual contains a comprehensive description of the
structure and function (operation) of a device.
KV31P100M120SF8RM
Data Sheet The Data Sheet is this document. It includes electrical characteristics
and signal connections.
KV31P100M120SF8
Chip Errata The chip mask set Errata provides additional or corrective information for
a particular device mask set.
KINETIS_xN51M 1
KMS User
Guide
The KMS User Guide provides a comprehensive description of the
features and functions of the Kinetis Motor Suite solution.
Kinetis Motor Suite User’s Guide
(KMS100UG)2
KMS API
Reference
Manual
The KMS API reference manual provides a comprehensive description of
the API of the Kinetis Motor Suite function blocks.
Kinetis Motor Suite API
Reference Manual
(KMS100RM)2
Package
drawing
Package dimensions are provided by part number:
MKV31F256VLL12
MKV31F256VLH12
MKV31F256VLH12P
Package drawing:
98ASS23308W
98ASS23234W
98ASS23234W
1. To find the associated resource, go to freescale.com and perform a search using this term with the x replaced by the
revision of the device you are using.
2. To find the associated resource, go to freescale.com and perform a search using Document ID
Figure 1 shows the functional modules in the chip.
2Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
Memories and Memory Interfaces
Program
(256 KB)
RAM
CRC
Programmable
Analog Timers Communication InterfacesSecurity
and Integrity
Clocks
Frequency-
Core
Debug
interfaces DSP
Interrupt
controller
Comparator
x2
16-bit
timer
Human-Machine
Interface (HMI)
Up to
System
DMA (16ch)
Low-leakage
wakeup locked loop
Serial
programming
interface
(EzPort)
reference
Internal
clocks
delay block
timers
interrupt
Periodic
oscillators
Low/high
frequency
UART
x3
®
Cortex™-M4ARM
FPU
voltage ref
Phase-
locked loop
x2
IC
2
Timers
x1 (8ch)
ADC x2
SPI
x2 x1
LPUART
High
performance low-power
70 GPIOs
(48 KB)
flash
Internal
watchdogs
and external
with 6-bit DAC
12-bit DAC
x2 (2ch)
16-bit
Random-
number
generator
Flash access
control
Figure 1. Functional block diagram
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 3
Freescale Semiconductor, Inc.
Table of Contents
1 Ratings....................................................................................5
1.1 Thermal handling ratings................................................. 5
1.2 Moisture handling ratings................................................ 5
1.3 ESD handling ratings.......................................................5
1.4 Voltage and current operating ratings............................. 5
2 General................................................................................... 6
2.1 AC electrical characteristics.............................................6
2.2 Nonswitching electrical specifications..............................6
2.2.1 Voltage and current operating requirements....... 6
2.2.2 LVD and POR operating requirements................7
2.2.3 Voltage and current operating behaviors.............8
2.2.4 Power mode transition operating behaviors........ 9
2.2.5 Power consumption operating behaviors............ 10
2.2.6 EMC radiated emissions operating behaviors.....16
2.2.7 Designing with radiated emissions in mind..........17
2.2.8 Capacitance attributes.........................................17
2.3 Switching specifications...................................................17
2.3.1 Device clock specifications..................................17
2.3.2 General switching specifications......................... 18
2.4 Thermal specifications.....................................................18
2.4.1 Thermal operating requirements......................... 19
2.4.2 Thermal attributes................................................19
3 Peripheral operating requirements and behaviors.................. 20
3.1 Core modules.................................................................. 20
3.1.1 SWD electricals .................................................. 20
3.1.2 JTAG electricals.................................................. 21
3.2 System modules.............................................................. 24
3.3 Clock modules................................................................. 24
3.3.1 MCG specifications..............................................24
3.3.2 IRC48M specifications.........................................27
3.3.3 Oscillator electrical specifications........................27
3.4 Memories and memory interfaces................................... 29
3.4.1 Flash electrical specifications..............................29
3.4.2 EzPort switching specifications........................... 31
3.5 Security and integrity modules........................................ 32
3.6 Analog............................................................................. 32
3.6.1 ADC electrical specifications............................... 32
3.6.2 CMP and 6-bit DAC electrical specifications....... 36
3.6.3 12-bit DAC electrical characteristics....................39
3.6.4 Voltage reference electrical specifications.......... 42
3.7 Timers..............................................................................43
3.8 Communication interfaces............................................... 43
3.8.1 DSPI switching specifications (limited voltage
range).................................................................. 44
3.8.2 DSPI switching specifications (full voltage
range).................................................................. 45
3.8.3 Inter-Integrated Circuit Interface (I2C) timing...... 47
3.8.4 UART switching specifications............................ 49
3.9 Kinetis Motor Suite.......................................................... 49
4 Dimensions............................................................................. 49
4.1 Obtaining package dimensions....................................... 49
5 Pinout......................................................................................50
5.1 KV31F Signal Multiplexing and Pin Assignments............50
5.2 Recommended connection for unused analog and
digital pins........................................................................54
5.3 KV31F Pinouts.................................................................55
6 Part identification.....................................................................57
6.1 Description.......................................................................57
6.2 Format............................................................................. 58
6.3 Fields............................................................................... 58
6.4 Example...........................................................................59
7 Terminology and guidelines.................................................... 59
7.1 Definitions........................................................................59
7.2 Examples.........................................................................59
7.3 Typical-value conditions.................................................. 60
7.4 Relationship between ratings and operating
requirements....................................................................60
7.5 Guidelines for ratings and operating requirements..........61
8 Revision History...................................................................... 61
4Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
1 Ratings
1.1 Thermal handling ratings
Symbol Description Min. Max. Unit Notes
TSTG Storage temperature –55 150 °C 1
TSDR Solder temperature, lead-free 260 °C 2
1. Determined according to JEDEC Standard JESD22-A103, High Temperature Storage Life.
2. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices.
1.2 Moisture handling ratings
Symbol Description Min. Max. Unit Notes
MSL Moisture sensitivity level 3 1
1. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices.
1.3 ESD handling ratings
Symbol Description Min. Max. Unit Notes
VHBM Electrostatic discharge voltage, human body model -2000 +2000 V 1
VCDM Electrostatic discharge voltage, charged-device
model
-500 +500 V 2
ILAT Latch-up current at ambient temperature of 105°C -100 +100 mA 3
1. Determined according to JEDEC Standard JESD22-A114, Electrostatic Discharge (ESD) Sensitivity Testing Human
Body Model (HBM).
2. Determined according to JEDEC Standard JESD22-C101, Field-Induced Charged-Device Model Test Method for
Electrostatic-Discharge-Withstand Thresholds of Microelectronic Components.
3. Determined according to JEDEC Standard JESD78, IC Latch-Up Test.
1.4 Voltage and current operating ratings
Ratings
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 5
Freescale Semiconductor, Inc.
Symbol Description Min. Max. Unit
VDD Digital supply voltage –0.3 3.8 V
IDD Digital supply current 158 mA
VDIO Digital input voltage –0.3 VDD + 0.3 V
VAIO Analog1–0.3 VDD + 0.3 V
IDMaximum current single pin limit (applies to all digital pins) –25 25 mA
VDDA Analog supply voltage VDD – 0.3 VDD + 0.3 V
1. Analog pins are defined as pins that do not have an associated general purpose I/O port function.
2 General
2.1 AC electrical characteristics
Unless otherwise specified, propagation delays are measured from the 50% to the 50%
point, and rise and fall times are measured at the 20% and 80% points, as shown in the
following figure.
80%
20%
50%
VIL
Input Signal
VIH
Fall Time
High
Low
Rise Time
Midpoint1
The midpoint is VIL + (VIH - VIL) / 2
Figure 2. Input signal measurement reference
2.2 Nonswitching electrical specifications
2.2.1 Voltage and current operating requirements
Table 1. Voltage and current operating requirements
Symbol Description Min. Max. Unit Notes
VDD Supply voltage 1.71 3.6 V
Table continues on the next page...
General
6Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
Table 1. Voltage and current operating requirements (continued)
Symbol Description Min. Max. Unit Notes
VDDA Analog supply voltage 1.71 3.6 V
VDD – VDDA VDD-to-VDDA differential voltage –0.1 0.1 V
VSS – VSSA VSS-to-VSSA differential voltage –0.1 0.1 V
VIH Input high voltage
2.7 V ≤ VDD ≤ 3.6 V
1.7 V ≤ VDD ≤ 2.7 V
0.7 × VDD
0.75 × VDD
V
V
VIL Input low voltage
2.7 V ≤ VDD ≤ 3.6 V
1.7 V ≤ VDD ≤ 2.7 V
0.35 × VDD
0.3 × VDD
V
V
VHYS Input hysteresis 0.06 × VDD V
IICIO Analog and I/O pin DC injection current — single pin
VIN < VSS-0.3V (Negative current injection) -3 mA
1
IICcont Contiguous pin DC injection current —regional limit,
includes sum of negative injection currents or sum of
positive injection currents of 16 contiguous pins
Negative current injection -25 mA
VODPU Open drain pullup voltage level VDD VDD V2
VRAM VDD voltage required to retain RAM 1.2 V
1. All analog and I/O pins are internally clamped to VSS through ESD protection diodes. If VIN is less than VIO_MIN or
greater than VIO_MAX, a current limiting resistor is required. The negative DC injection current limiting resistor is
calculated as R=(VIO_MIN-VIN)/|IICIO|.
2. Open drain outputs must be pulled to VDD.
2.2.2 LVD and POR operating requirements
Table 2. VDD supply LVD and POR operating requirements
Symbol Description Min. Typ. Max. Unit Notes
VPOR Falling VDD POR detect voltage 0.8 1.1 1.5 V
VLVDH Falling low-voltage detect threshold — high
range (LVDV=01)
2.48 2.56 2.64 V
VLVW1H
VLVW2H
VLVW3H
VLVW4H
Low-voltage warning thresholds — high range
Level 1 falling (LVWV=00)
Level 2 falling (LVWV=01)
Level 3 falling (LVWV=10)
Level 4 falling (LVWV=11)
2.62
2.72
2.82
2.92
2.70
2.80
2.90
3.00
2.78
2.88
2.98
3.08
V
V
V
V
1
Table continues on the next page...
General
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 7
Freescale Semiconductor, Inc.
Table 2. VDD supply LVD and POR operating requirements (continued)
Symbol Description Min. Typ. Max. Unit Notes
VHYSH Low-voltage inhibit reset/recover hysteresis —
high range
80 mV
VLVDL Falling low-voltage detect threshold — low
range (LVDV=00)
1.54 1.60 1.66 V
VLVW1L
VLVW2L
VLVW3L
VLVW4L
Low-voltage warning thresholds — low range
Level 1 falling (LVWV=00)
Level 2 falling (LVWV=01)
Level 3 falling (LVWV=10)
Level 4 falling (LVWV=11)
1.74
1.84
1.94
2.04
1.80
1.90
2.00
2.10
1.86
1.96
2.06
2.16
V
V
V
V
1
VHYSL Low-voltage inhibit reset/recover hysteresis —
low range
60 mV
VBG Bandgap voltage reference 0.97 1.00 1.03 V
tLPO Internal low power oscillator period — factory
trimmed
900 1000 1100 μs
1. Rising threshold is the sum of falling threshold and hysteresis voltage
2.2.3 Voltage and current operating behaviors
Table 3. Voltage and current operating behaviors
Symbol Description Min. Typ. Max. Unit Notes
VOH Output high voltage — Normal drive pad except
RESET_B
2.7 V ≤ VDD ≤ 3.6 V, IOH = -5 mA VDD – 0.5 V 1
1.71 V ≤ VDD ≤ 2.7 V, IOH = -2.5 mA VDD – 0.5 V
VOH Output high voltage — High drive pad except
RESET_B
2.7 V ≤ VDD ≤ 3.6 V, IOH = -20 mA VDD – 0.5 V 1
1.71 V ≤ VDD ≤ 2.7 V, IOH = -10 mA VDD – 0.5 V
IOHT Output high current total for all ports 100 mA
VOL Output low voltage — Normal drive pad except
RESET_B
2.7 V ≤ VDD ≤ 3.6 V, IOL = 5 mA 0.5 V 1
1.71 V ≤ VDD ≤ 2.7 V, IOL = 2.5 mA 0.5 V
VOL Output low voltage — High drive pad except
RESET_B
2.7 V ≤ VDD ≤ 3.6 V, IOL = 20 mA 0.5 V 1
1.71 V ≤ VDD ≤ 2.7 V, IOL = 10 mA 0.5 V
VOL Output low voltage — RESET_B
Table continues on the next page...
General
8Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
Table 3. Voltage and current operating behaviors (continued)
Symbol Description Min. Typ. Max. Unit Notes
2.7 V ≤ VDD ≤ 3.6 V, IOL = 3 mA 0.5 V
1.71 V ≤ VDD ≤ 2.7 V, IOL = 1.5 mA 0.5 V
IOLT Output low current total for all ports 100 mA
IIN Input leakage current (per pin) for full
temperature range
All pins other than high drive port pins 0.002 0.5 μA 1, 2
High drive port pins 0.004 0.5 μA
IIN Input leakage current (total all pins) for full
temperature range
1.0 μA 2
RPU Internal pullup resistors 20 50 3
RPD Internal pulldown resistors 20 50 4
1. PTB0, PTB1, PTC3, PTC4, PTD4, PTD5, PTD6, and PTD7 I/O have both high drive and normal drive capability
selected by the associated PTx_PCRn[DSE] control bit. All other GPIOs are normal drive only.
2. Measured at VDD=3.6V
3. Measured at VDD supply voltage = VDD min and Vinput = VSS
4. Measured at VDD supply voltage = VDD min and Vinput = VDD
2.2.4 Power mode transition operating behaviors
All specifications except tPOR, and VLLSxRUN recovery times in the following
table assume this clock configuration:
CPU and system clocks = 80 MHz
Bus clock = 40 MHz
Flash clock = 20 MHz
MCG mode: FEI
Table 4. Power mode transition operating behaviors
Symbol Description Min. Typ. Max. Unit Notes
tPOR After a POR event, amount of time from the
point VDD reaches 1.71 V to execution of the
first instruction across the operating
temperature range of the chip.
300 μs 1
VLLS0 RUN
140
μs
VLLS1 RUN
140
μs
VLLS2 RUN
80
μs
Table continues on the next page...
General
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 9
Freescale Semiconductor, Inc.
Table 4. Power mode transition operating behaviors (continued)
Symbol Description Min. Typ. Max. Unit Notes
VLLS3 RUN
80
μs
LLS2 RUN
6
μs
LLS3 RUN
6
μs
VLPS RUN
5.7
μs
STOP RUN
5.7
μs
1. Normal boot (FTFA_OPT[LPBOOT]=1)
2.2.5 Power consumption operating behaviors
The current parameters in the table below are derived from code executing a while(1)
loop from flash, unless otherwise noted.
The IDD typical values represent the statistical mean at 25°C, and the IDD maximum
values for RUN, WAIT, VLPR, and VLPW represent data collected at 125°C junction
temperature unless otherwise noted. The maximum values represent characterized
results equivalent to the mean plus three times the standard deviation (mean + 3 sigma).
Table 5. Power consumption operating behaviors
Symbol Description Min. Typ. Max. Unit Notes
IDDA Analog supply current See note mA 1
IDD_HSRUN High Speed Run mode current - all peripheral
clocks disabled, CoreMark benchmark code
executing from flash
@ 1.8V 25.66 26.35 mA 2, 3, 4
@ 3.0V 25.75 26.44 mA
IDD_HSRUN High Speed Run mode current - all peripheral
clocks disabled, code executing from flash
@ 1.8V 23.6 24.29 mA 2
@ 3.0V 23.7 24.39 mA
IDD_HSRUN High Speed Run mode current — all peripheral
clocks enabled, code executing from flash
@ 1.8V 31.9 32.59 mA 5
@ 3.0V 32.0 32.69 mA
Table continues on the next page...
General
10 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
Table 5. Power consumption operating behaviors (continued)
Symbol Description Min. Typ. Max. Unit Notes
IDD_RUN Run mode current in Compute operation —
CoreMark benchmark code executing from flash
@ 1.8V 15.8 16.49 mA 3, 4, 6
@ 3.0V 15.8 16.49 mA
IDD_RUN Run mode current in Compute operation —
code executing from flash
@ 1.8V 14.00 15.50 mA 6
@ 3.0V 14.00 15.69 mA
IDD_RUN Run mode current — all peripheral clocks
disabled, code executing from flash
@ 1.8V 15.3 15.99 mA 7
@ 3.0V 15.4 16.09 mA
IDD_RUN Run mode current — all peripheral clocks
enabled, code executing from flash
@ 1.8V 20.4 21.09 mA 8
@ 3.0V
@ 25°C 20.5 21.19 mA
@ 70°C 20.5 21.19 mA
@ 85°C 20.5 21.19 mA
@ 105°C 21.4 22.09 mA
IDD_RUN Run mode current — Compute operation, code
executing from flash
@ 1.8V 14.0 14.69 mA 9
@ 3.0V
@ 25°C 14.0 14.69 mA
@ 70°C 14.0 14.69 mA
@ 85°C 14.0 14.69 mA
@ 105°C 15.0 15.69 mA
IDD_WAIT Wait mode high frequency current at 3.0 V — all
peripheral clocks disabled
8.1 8.79 mA 7
IDD_WAIT Wait mode reduced frequency current at 3.0 V
— all peripheral clocks disabled
4.4 5.09 mA 10
IDD_VLPR Very-low-power run mode current in Compute
operation — CoreMark benchmark code
executing from flash
@ 1.8V 0.70 0.88 mA 3, 4, 11
@ 3.0V 0.70 0.88 mA
IDD_VLPR Very-low-power run mode current in Compute
operation, code executing from flash
0.61 0.79
Table continues on the next page...
General
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 11
Freescale Semiconductor, Inc.
Table 5. Power consumption operating behaviors (continued)
Symbol Description Min. Typ. Max. Unit Notes
@ 1.8V mA 11
@ 3.0V 0.61 0.79 mA
IDD_VLPR Very-low-power run mode current at 3.0 V — all
peripheral clocks disabled
0.68 0.87 mA 12
IDD_VLPR Very-low-power run mode current at 3.0 V — all
peripheral clocks enabled
1.10 1.28 mA 13
IDD_VLPW Very-low-power wait mode current at 3.0 V — all
peripheral clocks disabled
0.38 0.57 mA 14
IDD_STOP Stop mode current at 3.0 V
@ -40°C to 25°C 0.27 0.35 mA
@ 70°C 0.32 0.47 mA
@ 85°C 0.32 0.51 mA
@ 105°C 0.45 0.77 mA
IDD_VLPS Very-low-power stop mode current at 3.0 V
@ -40°C to 25°C 4.5 12.00 µA
@ 70°C 16.8 42.40 µA
@ 85°C 28.9 73.45 µA
@ 105°C 60.8 141.90 µA
IDD_LLS3 Low leakage stop mode 3 current at 3.0 V
@ -40°C to 25°C 2.6 3.75 µA
@ 70°C 6.6 12.00 µA
@ 85°C 10.5 17.25 µA
@ 105°C 21.0 40.70 µA
IDD_LLS2 Low leakage stop mode 2 current at 3.0 V
@ -40°C to 25°C 2.4 3.40 µA
@ 70°C 5.3 8.90 µA
@ 85°C 5.1 10.05 µA
@ 105°C 15.9 28.85 µA
IDD_VLLS3 Very low-leakage stop mode 3 current at 3.0 V
@ -40°C to 25°C 1.9 2.30 µA
@ 70°C 4.8 8.10 µA
@ 85°C 7.6 11.30 µA
@ 105°C 15.3 27.65 µA
IDD_VLLS2 Very low-leakage stop mode 2 current at 3.0 V
@ -40°C to 25°C 1.7 2.10 µA
@ 70°C 3.4 4.85 µA
@ 85°C 5.1 8.80 µA
@ 105°C 9.8 15.70 µA
IDD_VLLS1 Very low-leakage stop mode 1 current at 3.0 V
@ -40°C to 25°C 0.71 0.96 µA
Table continues on the next page...
General
12 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
Table 5. Power consumption operating behaviors (continued)
Symbol Description Min. Typ. Max. Unit Notes
@ 70°C 1.79 2.10 µA
@ 85°C 2.9 4.70 µA
@ 105°C 5.7 8.10 µA
IDD_VLLS0 Very low-leakage stop mode 0 current at 3.0 V
with POR detect circuit enabled
@ -40°C to 25°C 0.40 0.56 µA
@ 70°C 1.39 1.70 µA
@ 85°C 2.5 4.25 µA
@ 105°C 5.3 7.50 µA
IDD_VLLS0 Very low-leakage stop mode 0 current at 3.0 V
with POR detect circuit disabled
@ -40°C to 25°C 0.12 0.38 µA
@ 70°C 1.05 1.38 µA
@ 85°C 2.20 3.95 µA
@ 105°C 4.9 7.10 µA
1. The analog supply current is the sum of the active or disabled current for each of the analog modules on the device.
See each module's specification for its supply current.
2. 120MHz core and system clock, 60MHz bus clock, and 24MHz flash clock. MCG configured for PEE mode. All
peripheral clocks disabled.
3. Cache on and prefetch on, low compiler optimization.
4. Coremark benchmark compiled using IAR 7.2 with optimization level low.
5. 120MHz core and system clock, 60MHz bus clock, and 24MHz flash clock. MCG configured for PEE mode. All
peripheral clocks enabled.
6. 80 MHz core and system clock, 40 MHz bus clock, and 26.67 MHz flash clock. MCG configured for PEE mode.
Compute operation.
7. 80MHz core and system clock, 40MHz bus clock, and 26.67MHz flash clock. MCG configured for FEI mode. All
peripheral clocks disabled.
8. 80MHz core and system clock, 40MHz bus clock, and 26.67MHz flash clock. MCG configured for FEI mode. All
peripheral clocks enabled.
9. 80MHz core and system clock, 40MHz bus clock, and 26.67MHz flash clock. MCG configured for FEI mode. Compute
operation.
10. 25MHz core and system clock, 25MHz bus clock, and 25MHz flash clock. MCG configured for FEI mode.
11. 4 MHz core, system, and bus clock and 1MHz flash clock. MCG configured for BLPE mode. Compute operation.
Code executing from flash.
12. 4 MHz core, system, and bus clock and 1MHz flash clock. MCG configured for BLPE mode. All peripheral clocks
disabled. Code executing from flash.
13. 4 MHz core, system, and bus clock and 1MHz flash clock. MCG configured for BLPE mode. All peripheral clocks
enabled but peripherals are not in active operation. Code executing from flash.
14. 4 MHz core, system, and bus clock and 1MHz flash clock. MCG configured for BLPE mode. All peripheral clocks
disabled.
General
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 13
Freescale Semiconductor, Inc.
Table 6. Low power mode peripheral adders—typical value
Symbol Description Temperature (°C) Unit
-40 25 50 70 85 105
IIREFSTEN4MHz 4 MHz internal reference clock (IRC)
adder. Measured by entering STOP or
VLPS mode with 4 MHz IRC enabled.
56 56 56 56 56 56 µA
IIREFSTEN32KHz 32 kHz internal reference clock (IRC)
adder. Measured by entering STOP
mode with the 32 kHz IRC enabled.
52 52 52 52 52 52 µA
IEREFSTEN4MHz External 4 MHz crystal clock adder.
Measured by entering STOP or VLPS
mode with the crystal enabled.
206 228 237 245 251 258 uA
IEREFSTEN32KHz External 32 kHz crystal clock adder by
means of the OSC0_CR[EREFSTEN
and EREFSTEN] bits. Measured by
entering all modes with the crystal
enabled.
VLLS1
VLLS3
LLS
VLPS
STOP
440
440
490
510
510
490
490
490
560
560
540
540
540
560
560
560
560
560
560
560
570
570
570
610
610
580
580
680
680
680
nA
I48MIRC 48 Mhz internal reference clock 350 350 350 350 350 350 µA
ICMP CMP peripheral adder measured by
placing the device in VLLS1 mode with
CMP enabled using the 6-bit DAC and a
single external input for compare.
Includes 6-bit DAC power consumption.
22 22 22 22 22 22 µA
IUART UART peripheral adder measured by
placing the device in STOP or VLPS
mode with selected clock source waiting
for RX data at 115200 baud rate.
Includes selected clock source power
consumption.
MCGIRCLK (4 MHz internal reference
clock)
>OSCERCLK (4 MHz external crystal)
66
214
66
237
66
246
66
254
66
260
66
268
µA
IBG Bandgap adder when BGEN bit is set
and device is placed in VLPx, LLS, or
VLLSx mode.
45 45 45 45 45 45 µA
IADC ADC peripheral adder combining the
measured values at VDD and VDDA by
placing the device in STOP or VLPS
mode. ADC is configured for low power
mode using the internal clock and
continuous conversions.
42 42 42 42 42 42 µA
General
14 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
2.2.5.1 Diagram: Typical IDD_RUN operating behavior
The following data was measured under these conditions:
MCG in FBE mode for 50 MHz and lower frequencies. MCG in FEE mode at
frequencies between 50 MHz and 100MHz. MCG in PEE mode at frequencies
greater than 100 MHz.
No GPIOs toggled
Code execution from flash with cache enabled
For the ALLOFF curve, all peripheral clocks are disabled except FTFA
Figure 3. Run mode supply current vs. core frequency
General
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 15
Freescale Semiconductor, Inc.
Figure 4. VLPR mode supply current vs. core frequency
2.2.6 EMC radiated emissions operating behaviors
Table 7. EMC radiated emissions operating behaviors for 64 LQFP package
Parame
ter
Conditions Clocks Frequency range Level
(Typ.)
Unit Notes
VEME Device configuration, test
conditions and EM
testing per standard IEC
61967-2.
Supply voltages:
VDD = 3.3 V
Temp = 25°C
FSYS = 120 MHz
FBUS = 60 MHz
External crystal = 8 MHz
150 kHz–50 MHz 14 dBuV 1, 2, 3
50 MHz–150 MHz 23
150 MHz–500 MHz 23
500 MHz–1000 MHz 9
IEC level L 4
1. Measurements were made per IEC 61967-2 while the device was running typical application code.
2. Measurements were performed on a similar 64LQFP device.
3. The reported emission level is the value of the maximum measured emission, rounded up to the next whole number,
from among the measured orientations in each frequency range.
General
16 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
4. IEC Level Maximums: M ≤ 18dBmV, L ≤ 24dBmV, K ≤ 30dBmV, I ≤ 36dBmV, H ≤ 42dBmV .
2.2.7 Designing with radiated emissions in mind
To find application notes that provide guidance on designing your system to minimize
interference from radiated emissions:
1. Go to www.freescale.com.
2. Perform a keyword search for “EMC design.”
2.2.8 Capacitance attributes
Table 8. Capacitance attributes
Symbol Description Min. Max. Unit
CIN_A Input capacitance: analog pins 7 pF
CIN_D Input capacitance: digital pins 7 pF
2.3 Switching specifications
2.3.1 Device clock specifications
Table 9. Device clock specifications
Symbol Description Min. Max. Unit Notes
High Speed run mode
fSYS System and core clock 120 MHz
fBUS Bus clock 60 MHz
Normal run mode (and High Speed run mode unless otherwise specified above)
fSYS System and core clock 80 MHz
fBUS Bus clock 50 MHz
fFLASH Flash clock 26.67 MHz
fLPTMR LPTMR clock 25 MHz
VLPR mode1
fSYS System and core clock 4 MHz
fBUS Bus clock 4 MHz
fFLASH Flash clock 1 MHz
fERCLK External reference clock 16 MHz
Table continues on the next page...
General
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 17
Freescale Semiconductor, Inc.
Table 9. Device clock specifications (continued)
Symbol Description Min. Max. Unit Notes
fLPTMR_pin LPTMR clock 25 MHz
fLPTMR_ERCLK LPTMR external reference clock 16 MHz
1. The frequency limitations in VLPR mode here override any frequency specification listed in the timing specification for
any other module.
2.3.2 General switching specifications
These general purpose specifications apply to all signals configured for GPIO, UART,
and timers.
Table 10. General switching specifications
Symbol Description Min. Max. Unit Notes
GPIO pin interrupt pulse width (digital glitch filter
disabled) — Synchronous path
1.5 Bus clock
cycles
1, 2
External RESET and NMI pin interrupt pulse width —
Asynchronous path
100 ns 3
GPIO pin interrupt pulse width (digital glitch filter
disabled, passive filter disabled) — Asynchronous
path
50 ns 4
Mode select (EZP_CS) hold time after reset
deassertion
2 Bus clock
cycles
Port rise and fall time
Slew disabled
1.71 ≤ VDD ≤ 2.7V
2.7 ≤ VDD ≤ 3.6V
Slew enabled
1.71 ≤ VDD ≤ 2.7V
2.7 ≤ VDD ≤ 3.6V
10
5
30
16
ns
ns
ns
ns
5
1. This is the minimum pulse width that is guaranteed to pass through the pin synchronization circuitry. Shorter pulses may
or may not be recognized. In Stop, VLPS, LLS, and VLLSx modes, the synchronizer is bypassed so shorter pulses can
be recognized in that case.
2. The greater of synchronous and asynchronous timing must be met.
3. These pins have a passive filter enabled on the inputs. This is the shortest pulse width that is guaranteed to be
recognized.
4. These pins do not have a passive filter on the inputs. This is the shortest pulse width that is guaranteed to be
recognized.
5. 25 pF load
General
18 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
2.4 Thermal specifications
2.4.1 Thermal operating requirements
Table 11. Thermal operating requirements
Symbol Description Min. Max. Unit Notes
TJDie junction temperature –40 125 °C
TAAmbient temperature –40 105 °C 1
1. Maximum TA can be exceeded only if the user ensures that TJ does not exceed maximum TJ. The simplest method to
determine TJ is: TJ = TA + RΘJA × chip power dissipation.
2.4.2 Thermal attributes
Board type Symbol Description 100 LQFP 64 LQFP Unit Notes
Single-layer
(1s)
RθJA Thermal
resistance,
junction to
ambient
(natural
convection)
61 67 °C/W 1
Four-layer
(2s2p)
RθJA Thermal
resistance,
junction to
ambient
(natural
convection)
48 48 °C/W 2
Single-layer
(1s)
RθJMA Thermal
resistance,
junction to
ambient (200
ft./min. air
speed)
51 55 °C/W 3
Four-layer
(2s2p)
RθJMA Thermal
resistance,
junction to
ambient (200
ft./min. air
speed)
42 42 °C/W 3
RθJB Thermal
resistance,
junction to
board
34 31 °C/W 4
RθJC Thermal
resistance,
junction to case
16 16 °C/W 5
Table continues on the next page...
General
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 19
Freescale Semiconductor, Inc.
Board type Symbol Description 100 LQFP 64 LQFP Unit Notes
ΨJT Thermal
characterizatio
n parameter,
junction to
package top
outside center
(natural
convection)
3 3 °C/W 6
1. Determined according to JEDEC Standard JESD51-2, Integrated Circuits Thermal Test Method Environmental
Conditions—Natural Convection (Still Air)with the single layer board horizontal. Board meets JESD51-9 specification.
2. Determined according to JEDEC Standard JESD51-2, Integrated Circuits Thermal Test Method Environmental
Conditions—Natural Convection (Still Air).
3. Determined according to JEDEC Standard JESD51-6, Integrated Circuits Thermal Test Method Environmental
Conditions—Forced Convection (Moving Air) with the board horizontal.
4. Determined according to JEDEC Standard JESD51-8, Integrated Circuit Thermal Test Method Environmental
Conditions—Junction-to-Board.
5. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883
Method 1012.1).
6. Thermal characterization parameter indicating the temperature difference between package top and the junction
temperature per JEDEC JESD51-2.
3 Peripheral operating requirements and behaviors
3.1 Core modules
3.1.1 SWD electricals
Table 12. SWD full voltage range electricals
Symbol Description Min. Max. Unit
Operating voltage 1.71 3.6 V
S1 SWD_CLK frequency of operation
Serial wire debug
0
33
MHz
S2 SWD_CLK cycle period 1/S1 ns
S3 SWD_CLK clock pulse width
Serial wire debug
15
ns
S4 SWD_CLK rise and fall times 3 ns
S9 SWD_DIO input data setup time to SWD_CLK rise 8 ns
S10 SWD_DIO input data hold time after SWD_CLK rise 1.4 ns
S11 SWD_CLK high to SWD_DIO data valid 25 ns
S12 SWD_CLK high to SWD_DIO high-Z 5 ns
Peripheral operating requirements and behaviors
20 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
S2
S3 S3
S4 S4
SWD_CLK (input)
Figure 5. Serial wire clock input timing
S11
S12
S11
S9 S10
Input data valid
Output data valid
Output data valid
SWD_CLK
SWD_DIO
SWD_DIO
SWD_DIO
SWD_DIO
Figure 6. Serial wire data timing
3.1.2 JTAG electricals
Table 13. JTAG limited voltage range electricals
Symbol Description Min. Max. Unit
Operating voltage 2.7 3.6 V
J1 TCLK frequency of operation
Boundary Scan
JTAG and CJTAG
0
0
10
20
MHz
J2 TCLK cycle period 1/J1 ns
J3 TCLK clock pulse width
50
ns
Table continues on the next page...
Peripheral operating requirements and behaviors
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 21
Freescale Semiconductor, Inc.
Table 13. JTAG limited voltage range electricals (continued)
Symbol Description Min. Max. Unit
Boundary Scan
JTAG and CJTAG
25 ns
J4 TCLK rise and fall times 3 ns
J5 Boundary scan input data setup time to TCLK rise 20 ns
J6 Boundary scan input data hold time after TCLK rise 1 ns
J7 TCLK low to boundary scan output data valid 25 ns
J8 TCLK low to boundary scan output high-Z 25 ns
J9 TMS, TDI input data setup time to TCLK rise 8 ns
J10 TMS, TDI input data hold time after TCLK rise 1 ns
J11 TCLK low to TDO data valid 19 ns
J12 TCLK low to TDO high-Z 19 ns
J13 TRST assert time 100 ns
J14 TRST setup time (negation) to TCLK high 8 ns
Table 14. JTAG full voltage range electricals
Symbol Description Min. Max. Unit
Operating voltage 1.71 3.6 V
J1 TCLK frequency of operation
Boundary Scan
JTAG and CJTAG
0
0
10
15
MHz
J2 TCLK cycle period 1/J1 ns
J3 TCLK clock pulse width
Boundary Scan
JTAG and CJTAG
50
33
ns
ns
J4 TCLK rise and fall times 3 ns
J5 Boundary scan input data setup time to TCLK rise 20 ns
J6 Boundary scan input data hold time after TCLK rise 1.4 ns
J7 TCLK low to boundary scan output data valid 27 ns
J8 TCLK low to boundary scan output high-Z 27 ns
J9 TMS, TDI input data setup time to TCLK rise 8 ns
J10 TMS, TDI input data hold time after TCLK rise 1.4 ns
J11 TCLK low to TDO data valid 26.2 ns
J12 TCLK low to TDO high-Z 26.2 ns
J13 TRST assert time 100 ns
J14 TRST setup time (negation) to TCLK high 8 ns
Peripheral operating requirements and behaviors
22 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
J2
J3 J3
J4 J4
TCLK (input)
Figure 7. Test clock input timing
J7
J8
J7
J5 J6
Input data valid
Output data valid
Output data valid
TCLK
Data inputs
Data outputs
Data outputs
Data outputs
Figure 8. Boundary scan (JTAG) timing
Peripheral operating requirements and behaviors
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 23
Freescale Semiconductor, Inc.
J11
J12
J11
J9 J10
Input data valid
Output data valid
Output data valid
TCLK
TDI/TMS
TDO
TDO
TDO
Figure 9. Test Access Port timing
J14
J13
TCLK
TRST
Figure 10. TRST timing
3.2 System modules
There are no specifications necessary for the device's system modules.
3.3 Clock modules
Peripheral operating requirements and behaviors
24 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
3.3.1 MCG specifications
Table 15. MCG specifications
Symbol Description Min. Typ. Max. Unit Notes
fints_ft Internal reference frequency (slow clock) —
factory trimmed at nominal VDD and 25 °C
32.768 kHz
Δfints_t Total deviation of internal reference frequency
(slow clock) over voltage and temperature
+0.5/-0.7 ± 2 %
fints_t Internal reference frequency (slow clock) —
user trimmed
31.25 39.0625 kHz
Δfdco_res_t Resolution of trimmed average DCO output
frequency at fixed voltage and temperature —
using SCTRIM and SCFTRIM
± 0.3 ± 0.6 %fdco 1
Δfdco_t Total deviation of trimmed average DCO output
frequency over voltage and temperature
+0.5/-0.7 ± 2 %fdco 1, 2
Δfdco_t Total deviation of trimmed average DCO output
frequency over fixed voltage and temperature
range of 0–70°C
± 0.3 ± 1.5 %fdco 1
fintf_ft Internal reference frequency (fast clock) —
factory trimmed at nominal VDD and 25°C
4 MHz
Δfintf_ft Frequency deviation of internal reference clock
(fast clock) over temperature and voltage —
factory trimmed at nominal VDD and 25 °C
+1/-2 ± 5 %fintf_ft
fintf_t Internal reference frequency (fast clock) —
user trimmed at nominal VDD and 25 °C
3 5 MHz
floc_low Loss of external clock minimum frequency —
RANGE = 00
(3/5) x
fints_t
kHz
floc_high Loss of external clock minimum frequency —
RANGE = 01, 10, or 11
(16/5) x
fints_t
kHz
FLL
ffll_ref FLL reference frequency range 31.25 39.0625 kHz
fdco DCO output
frequency range
Low range (DRS=00)
640 × ffll_ref
20 20.97 25 MHz 3, 4
Mid range (DRS=01)
1280 × ffll_ref
40 41.94 50 MHz
Mid-high range (DRS=10)
1920 × ffll_ref
60 62.91 75 MHz
High range (DRS=11)
2560 × ffll_ref
80 83.89 100 MHz
fdco_t_DMX3
2
DCO output
frequency
Low range (DRS=00)
732 × ffll_ref
23.99 MHz 5, 6
Mid range (DRS=01)
1464 × ffll_ref
47.97 MHz
Mid-high range (DRS=10) 71.99 MHz
Table continues on the next page...
Peripheral operating requirements and behaviors
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 25
Freescale Semiconductor, Inc.
Table 15. MCG specifications (continued)
Symbol Description Min. Typ. Max. Unit Notes
2197 × ffll_ref
High range (DRS=11)
2929 × ffll_ref
95.98 MHz
Jcyc_fll FLL period jitter
fVCO = 48 MHz
fVCO = 98 MHz
180
150
ps
tfll_acquire FLL target frequency acquisition time 1 ms 7
PLL
fvco VCO operating frequency 48.0 120 MHz
Ipll PLL operating current
PLL @ 96 MHz (fosc_hi_1 = 8 MHz, fpll_ref
= 2 MHz, VDIV multiplier = 48)
1060 µA 8
Ipll PLL operating current
PLL @ 48 MHz (fosc_hi_1 = 8 MHz, fpll_ref
= 2 MHz, VDIV multiplier = 24)
600 µA 8
fpll_ref PLL reference frequency range 2.0 4.0 MHz
Jcyc_pll PLL period jitter (RMS)
fvco = 48 MHz
fvco = 100 MHz
120
75
ps
ps
9
Jacc_pll PLL accumulated jitter over 1µs (RMS)
fvco = 48 MHz
fvco = 100 MHz
1350
600
ps
ps
9
Dlock Lock entry frequency tolerance ± 1.49 ± 2.98 %
Dunl Lock exit frequency tolerance ± 4.47 ± 5.97 %
tpll_lock Lock detector detection time 150 × 10-6
+ 1075(1/
fpll_ref)
s10
1. This parameter is measured with the internal reference (slow clock) being used as a reference to the FLL (FEI clock
mode).
2. 2.0 V <= VDD <= 3.6 V.
3. These typical values listed are with the slow internal reference clock (FEI) using factory trim and DMX32=0.
4. The resulting system clock frequencies should not exceed their maximum specified values. The DCO frequency
deviation (Δfdco_t) over voltage and temperature should be considered.
5. These typical values listed are with the slow internal reference clock (FEI) using factory trim and DMX32=1.
6. The resulting clock frequency must not exceed the maximum specified clock frequency of the device.
7. This specification applies to any time the FLL reference source or reference divider is changed, trim value is changed,
DMX32 bit is changed, DRS bits are changed, or changing from FLL disabled (BLPE, BLPI) to FLL enabled (FEI, FEE,
FBE, FBI). If a crystal/resonator is being used as the reference, this specification assumes it is already running.
8. Excludes any oscillator currents that are also consuming power while PLL is in operation.
9. This specification was obtained using a Freescale developed PCB. PLL jitter is dependent on the noise characteristics of
each PCB and results will vary.
10. This specification applies to any time the PLL VCO divider or reference divider is changed, or changing from PLL
disabled (BLPE, BLPI) to PLL enabled (PBE, PEE). If a crystal/resonator is being used as the reference, this
specification assumes it is already running.
Peripheral operating requirements and behaviors
26 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
3.3.2 IRC48M specifications
Table 16. IRC48M specifications
Symbol Description Min. Typ. Max. Unit Notes
VDD Supply voltage 1.71 3.6 V
IDD48M Supply current 400 500 μA
firc48m Internal reference frequency 48 MHz
Δfirc48m_ol_hv Open loop total deviation of IRC48M frequency at
high voltage (VDD=1.89V-3.6V) over 0°C to 70°C
± 0.2 ± 0.5 %firc48m 1
Δfirc48m_ol_hv Open loop total deviation of IRC48M frequency at
high voltage (VDD=1.89V-3.6V) over full
temperature
± 0.4 ± 1.0 %firc48m 1
Δfirc48m_ol_lv Open loop total deviation of IRC48M frequency at
low voltage (VDD=1.71V-1.89V) over full
temperature
± 0.5 ± 1.5 %firc48m 1
Jcyc_irc48m Period Jitter (RMS) 35 150 ps
tirc48mst Startup time 2 3 μs 2
1. The maximum value represents characterized results equivalent to the mean plus or minus three times the standard
deviation (mean ± 3 sigma).
2. IRC48M startup time is defined as the time between clock enablement and clock availability for system use. Enable
the clock by one of the following settings:
MCG operating in an external clocking mode and MCG_C7[OSCSEL]=10 or MCG_C5[PLLCLKEN0]=1, or
SIM_SOPT2[PLLFLLSEL]=11
3.3.3 Oscillator electrical specifications
3.3.3.1 Oscillator DC electrical specifications
Table 17. Oscillator DC electrical specifications
Symbol Description Min. Typ. Max. Unit Notes
VDD Supply voltage 1.71 3.6 V
IDDOSC Supply current — low-power mode (HGO=0)
32 kHz
4 MHz
8 MHz (RANGE=01)
16 MHz
24 MHz
32 MHz
500
200
300
950
1.2
1.5
nA
μA
μA
μA
mA
mA
1
IDDOSC Supply current — high-gain mode (HGO=1) 1
Table continues on the next page...
Peripheral operating requirements and behaviors
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 27
Freescale Semiconductor, Inc.
Table 17. Oscillator DC electrical specifications (continued)
Symbol Description Min. Typ. Max. Unit Notes
32 kHz
4 MHz
8 MHz (RANGE=01)
16 MHz
24 MHz
32 MHz
25
400
500
2.5
3
4
μA
μA
μA
mA
mA
mA
CxEXTAL load capacitance 2, 3
CyXTAL load capacitance 2, 3
RFFeedback resistor — low-frequency, low-power
mode (HGO=0)
2, 4
Feedback resistor — low-frequency, high-gain
mode (HGO=1)
10
Feedback resistor — high-frequency, low-
power mode (HGO=0)
Feedback resistor — high-frequency, high-gain
mode (HGO=1)
1
RSSeries resistor — low-frequency, low-power
mode (HGO=0)
Series resistor — low-frequency, high-gain
mode (HGO=1)
200
Series resistor — high-frequency, low-power
mode (HGO=0)
Series resistor — high-frequency, high-gain
mode (HGO=1)
0
Vpp5Peak-to-peak amplitude of oscillation (oscillator
mode) — low-frequency, low-power mode
(HGO=0)
0.6 V
Peak-to-peak amplitude of oscillation (oscillator
mode) — low-frequency, high-gain mode
(HGO=1)
VDD V
Peak-to-peak amplitude of oscillation (oscillator
mode) — high-frequency, low-power mode
(HGO=0)
0.6 V
Peak-to-peak amplitude of oscillation (oscillator
mode) — high-frequency, high-gain mode
(HGO=1)
VDD V
1. VDD=3.3 V, Temperature =25 °C
2. See crystal or resonator manufacturer's recommendation
3. Cx and Cy can be provided by using either integrated capacitors or external components.
4. When low-power mode is selected, RF is integrated and must not be attached externally.
5. The EXTAL and XTAL pins should only be connected to required oscillator components and must not be connected to
any other device.
Peripheral operating requirements and behaviors
28 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
3.3.3.2 Oscillator frequency specifications
Table 18. Oscillator frequency specifications
Symbol Description Min. Typ. Max. Unit Notes
fosc_lo Oscillator crystal or resonator frequency — low-
frequency mode (MCG_C2[RANGE]=00)
32 40 kHz
fosc_hi_1 Oscillator crystal or resonator frequency —
high-frequency mode (low range)
(MCG_C2[RANGE]=01)
3 8 MHz
fosc_hi_2 Oscillator crystal or resonator frequency —
high frequency mode (high range)
(MCG_C2[RANGE]=1x)
8 32 MHz
fec_extal Input clock frequency (external clock mode) 50 MHz 1, 2
tdc_extal Input clock duty cycle (external clock mode) 40 50 60 %
tcst Crystal startup time — 32 kHz low-frequency,
low-power mode (HGO=0)
750 ms 3, 4
Crystal startup time — 32 kHz low-frequency,
high-gain mode (HGO=1)
250 ms
Crystal startup time — 8 MHz high-frequency
(MCG_C2[RANGE]=01), low-power mode
(HGO=0)
0.6 ms
Crystal startup time — 8 MHz high-frequency
(MCG_C2[RANGE]=01), high-gain mode
(HGO=1)
1 ms
1. Other frequency limits may apply when external clock is being used as a reference for the FLL or PLL.
2. When transitioning from FEI or FBI to FBE mode, restrict the frequency of the input clock so that, when it is divided by
FRDIV, it remains within the limits of the DCO input clock frequency.
3. Proper PC board layout procedures must be followed to achieve specifications.
4. Crystal startup time is defined as the time between the oscillator being enabled and the OSCINIT bit in the MCG_S
register being set.
3.4 Memories and memory interfaces
3.4.1 Flash electrical specifications
This section describes the electrical characteristics of the flash memory module.
3.4.1.1 Flash timing specifications — program and erase
The following specifications represent the amount of time the internal charge pumps
are active and do not include command overhead.
Peripheral operating requirements and behaviors
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 29
Freescale Semiconductor, Inc.
Table 19. NVM program/erase timing specifications
Symbol Description Min. Typ. Max. Unit Notes
thvpgm4 Longword Program high-voltage time 7.5 18 μs
thversscr Sector Erase high-voltage time 13 113 ms 1
thversall Erase All high-voltage time 104 904 ms 1
1. Maximum time based on expectations at cycling end-of-life.
3.4.1.2 Flash timing specifications — commands
Table 20. Flash command timing specifications
Symbol Description Min. Typ. Max. Unit Notes
trd1sec2k Read 1s Section execution time (flash sector) 60 μs 1
tpgmchk Program Check execution time 45 μs 1
trdrsrc Read Resource execution time 30 μs 1
tpgm4 Program Longword execution time 65 145 μs
tersscr Erase Flash Sector execution time 14 114 ms 2
trd1all Read 1s All Blocks execution time 1.8 ms 1
trdonce Read Once execution time 30 μs 1
tpgmonce Program Once execution time 100 μs
tersall Erase All Blocks execution time 175 1300 ms 2
tvfykey Verify Backdoor Access Key execution time 30 μs 1
1. Assumes 25 MHz flash clock frequency.
2. Maximum times for erase parameters based on expectations at cycling end-of-life.
3.4.1.3 Flash high voltage current behaviors
Table 21. Flash high voltage current behaviors
Symbol Description Min. Typ. Max. Unit
IDD_PGM Average current adder during high voltage
flash programming operation
2.5 6.0 mA
IDD_ERS Average current adder during high voltage
flash erase operation
1.5 4.0 mA
3.4.1.4 Reliability specifications
Table 22. NVM reliability specifications
Symbol Description Min. Typ.1Max. Unit Notes
Program Flash
Table continues on the next page...
Peripheral operating requirements and behaviors
30 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
Table 22. NVM reliability specifications (continued)
Symbol Description Min. Typ.1Max. Unit Notes
tnvmretp10k Data retention after up to 10 K cycles 5 50 years
tnvmretp1k Data retention after up to 1 K cycles 20 100 years
nnvmcycp Cycling endurance 10 K 50 K cycles 2
1. Typical data retention values are based on measured response accelerated at high temperature and derated to a
constant 25 °C use profile. Engineering Bulletin EB618 does not apply to this technology. Typical endurance defined in
Engineering Bulletin EB619.
2. Cycling endurance represents number of program/erase cycles at –40 °C ≤ Tj ≤ 125 °C.
3.4.2 EzPort switching specifications
Table 23. EzPort switching specifications
Num Description Min. Max. Unit
Operating voltage 1.71 3.6 V
EP1 EZP_CK frequency of operation (all commands except
READ)
fSYS/2 MHz
EP1a EZP_CK frequency of operation (READ command) fSYS/8 MHz
EP2 EZP_CS negation to next EZP_CS assertion 2 x tEZP_CK ns
EP3 EZP_CS input valid to EZP_CK high (setup) 5 ns
EP4 EZP_CK high to EZP_CS input invalid (hold) 5 ns
EP5 EZP_D input valid to EZP_CK high (setup) 2 ns
EP6 EZP_CK high to EZP_D input invalid (hold) 5 ns
EP7 EZP_CK low to EZP_Q output valid 25 ns
EP8 EZP_CK low to EZP_Q output invalid (hold) 0 ns
EP9 EZP_CS negation to EZP_Q tri-state 12 ns
Peripheral operating requirements and behaviors
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 31
Freescale Semiconductor, Inc.
EP2
EP3 EP4
EP5 EP6
EP7 EP8
EP9
EZP_CK
EZP_CS
EZP_Q (output)
EZP_D (input)
Figure 11. EzPort Timing Diagram
3.5 Security and integrity modules
There are no specifications necessary for the device's security and integrity modules.
3.6 Analog
3.6.1 ADC electrical specifications
The 16-bit accuracy specifications listed in Table 24 and Table 25 are achievable on the
differential pins ADCx_DPx, ADCx_DMx.
All other ADC channels meet the 13-bit differential/12-bit single-ended accuracy
specifications.
3.6.1.1 16-bit ADC operating conditions
Table 24. 16-bit ADC operating conditions
Symbol Description Conditions Min. Typ.1Max. Unit Notes
VDDA Supply voltage Absolute 1.71 3.6 V
ΔVDDA Supply voltage Delta to VDD (VDD – VDDA) -100 0 +100 mV 2
Table continues on the next page...
Peripheral operating requirements and behaviors
32 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
Table 24. 16-bit ADC operating conditions (continued)
Symbol Description Conditions Min. Typ.1Max. Unit Notes
ΔVSSA Ground voltage Delta to VSS (VSS – VSSA) -100 0 +100 mV 2
VREFH ADC reference
voltage high
1.13 VDDA VDDA V
VREFL ADC reference
voltage low
VSSA VSSA VSSA V
VADIN Input voltage 16-bit differential mode
All other modes
VREFL
VREFL
31/32 *
VREFH
VREFH
V
CADIN Input
capacitance
16-bit mode
8-bit / 10-bit / 12-bit
modes
8
4
10
5
pF
RADIN Input series
resistance
2 5
RAS Analog source
resistance
(external)
13-bit / 12-bit modes
fADCK < 4 MHz
5
3
fADCK ADC conversion
clock frequency
≤ 13-bit mode 1.0 24.0 MHz 4
fADCK ADC conversion
clock frequency
16-bit mode 2.0 12.0 MHz 4
Crate ADC conversion
rate
≤ 13-bit modes
No ADC hardware averaging
Continuous conversions
enabled, subsequent
conversion time
20
1200
Ksps
5
Crate ADC conversion
rate
16-bit mode
No ADC hardware averaging
Continuous conversions
enabled, subsequent
conversion time
37
461
Ksps
5
1. Typical values assume VDDA = 3.0 V, Temp = 25 °C, fADCK = 1.0 MHz, unless otherwise stated. Typical values are for
reference only, and are not tested in production.
2. DC potential difference.
3. This resistance is external to MCU. To achieve the best results, the analog source resistance must be kept as low as
possible. The results in this data sheet were derived from a system that had < 8 Ω analog source resistance. The
RAS/CAS time constant should be kept to < 1 ns.
4. To use the maximum ADC conversion clock frequency, CFG2[ADHSC] must be set and CFG1[ADLPC] must be clear.
5. For guidelines and examples of conversion rate calculation, download the ADC calculator tool.
Peripheral operating requirements and behaviors
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 33
Freescale Semiconductor, Inc.
RAS
VAS CAS
ZAS
VADIN
ZADIN
RADIN
RADIN
RADIN
RADIN
CADIN
Pad
leakage
due to
input
protection
INPUT PIN
INPUT PIN
INPUT PIN
SIMPLIFIED
INPUT PIN EQUIVALENT
CIRCUIT
SIMPLIFIED
CHANNEL SELECT
CIRCUIT
ADC SAR
ENGINE
Figure 12. ADC input impedance equivalency diagram
3.6.1.2 16-bit ADC electrical characteristics
Table 25. 16-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA)
Symbol Description Conditions1Min. Typ.2Max. Unit Notes
IDDA_ADC Supply current 0.215 1.7 mA 3
fADACK
ADC asynchronous
clock source
ADLPC = 1, ADHSC = 0
ADLPC = 1, ADHSC = 1
ADLPC = 0, ADHSC = 0
ADLPC = 0, ADHSC = 1
1.2
2.4
3.0
4.4
2.4
4.0
5.2
6.2
3.9
6.1
7.3
9.5
MHz
MHz
MHz
MHz
tADACK = 1/
fADACK
Sample Time See Reference Manual chapter for sample times
TUE Total unadjusted
error
12-bit modes
<12-bit modes
±4
±1.4
±6.8
±2.1
LSB45
DNL Differential non-
linearity
12-bit modes
<12-bit modes
±0.7
±0.2
–1.1 to
+1.9
–0.3 to
0.5
LSB45
INL Integral non-linearity 12-bit modes ±1.0 –2.7 to
+1.9
LSB45
Table continues on the next page...
Peripheral operating requirements and behaviors
34 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
Table 25. 16-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA) (continued)
Symbol Description Conditions1Min. Typ.2Max. Unit Notes
<12-bit modes ±0.5 –0.7 to
+0.5
EFS Full-scale error 12-bit modes
<12-bit modes
–4
–1.4
–5.4
–1.8
LSB4VADIN = VDDA5
EQQuantization error 16-bit modes
≤13-bit modes
–1 to 0
±0.5
LSB4
ENOB Effective number of
bits
16-bit differential mode
Avg = 32
Avg = 4
16-bit single-ended mode
Avg = 32
Avg = 4
12.8
11.9
12.2
11.4
14.5
13.8
13.9
13.1
bits
bits
bits
bits
6
SINAD Signal-to-noise plus
distortion
See ENOB 6.02 × ENOB + 1.76 dB
THD Total harmonic
distortion
16-bit differential mode
Avg = 32
16-bit single-ended mode
Avg = 32
-94
-85
dB
dB
7
SFDR Spurious free
dynamic range
16-bit differential mode
Avg = 32
16-bit single-ended mode
Avg = 32
82
78
95
90
dB
dB
7
EIL Input leakage error IIn × RAS mV IIn = leakage
current
(refer to the
MCU's voltage
and current
operating
ratings)
Temp sensor slope Across the full temperature
range of the device
1.55 1.62 1.69 mV/°C 8
VTEMP25 Temp sensor voltage 25 °C 706 716 726 mV 8
1. All accuracy numbers assume the ADC is calibrated with VREFH = VDDA
2. Typical values assume VDDA = 3.0 V, Temp = 25 °C, fADCK = 2.0 MHz unless otherwise stated. Typical values are for
reference only and are not tested in production.
3. The ADC supply current depends on the ADC conversion clock speed, conversion rate and ADC_CFG1[ADLPC] (low
power). For lowest power operation, ADC_CFG1[ADLPC] must be set, the ADC_CFG2[ADHSC] bit must be clear with
1 MHz ADC conversion clock speed.
Peripheral operating requirements and behaviors
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 35
Freescale Semiconductor, Inc.
4. 1 LSB = (VREFH - VREFL)/2N
5. ADC conversion clock < 16 MHz, Max hardware averaging (AVGE = %1, AVGS = %11)
6. Input data is 100 Hz sine wave. ADC conversion clock < 12 MHz.
7. Input data is 1 kHz sine wave. ADC conversion clock < 12 MHz.
8. ADC conversion clock < 3 MHz
Typical ADC 16-bit Differential ENOB vs ADC Clock
100Hz, 90% FS Sine Input
ENOB
ADC Clock Frequency (MHz)
15.00
14.70
14.40
14.10
13.80
13.50
13.20
12.90
12.60
12.30
12.00
1 2 3 4 5 6 7 8 9 10 1211
Hardware Averaging Disabled
Averaging of 4 samples
Averaging of 8 samples
Averaging of 32 samples
Figure 13. Typical ENOB vs. ADC_CLK for 16-bit differential mode
Typical ADC 16-bit Single-Ended ENOB vs ADC Clock
100Hz, 90% FS Sine Input
ENOB
ADC Clock Frequency (MHz)
14.00
13.75
13.25
13.00
12.75
12.50
12.00
11.75
11.50
11.25
11.00
1 2 3 4 5 6 7 8 9 10 1211
Averaging of 4 samples
Averaging of 32 samples
13.50
12.25
Figure 14. Typical ENOB vs. ADC_CLK for 16-bit single-ended mode
Peripheral operating requirements and behaviors
36 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
3.6.2 CMP and 6-bit DAC electrical specifications
Table 26. Comparator and 6-bit DAC electrical specifications
Symbol Description Min. Typ. Max. Unit
VDD Supply voltage 1.71 3.6 V
IDDHS Supply current, High-speed mode (EN=1, PMODE=1) 200 μA
IDDLS Supply current, low-speed mode (EN=1, PMODE=0) 20 μA
VAIN Analog input voltage VSS – 0.3 VDD V
VAIO Analog input offset voltage 20 mV
VHAnalog comparator hysteresis1
CR0[HYSTCTR] = 00
CR0[HYSTCTR] = 01
CR0[HYSTCTR] = 10
CR0[HYSTCTR] = 11
5
10
20
30
mV
mV
mV
mV
VCMPOh Output high VDD – 0.5 V
VCMPOl Output low 0.5 V
tDHS Propagation delay, high-speed mode (EN=1, PMODE=1) 20 50 200 ns
tDLS Propagation delay, low-speed mode (EN=1, PMODE=0) 80 250 600 ns
Analog comparator initialization delay2 40 μs
IDAC6b 6-bit DAC current adder (enabled) 7 μA
INL 6-bit DAC integral non-linearity –0.5 0.5 LSB3
DNL 6-bit DAC differential non-linearity –0.3 0.3 LSB
1. Typical hysteresis is measured with input voltage range limited to 0.6 to VDD–0.6 V.
2. Comparator initialization delay is defined as the time between software writes to change control inputs (Writes to
CMP_DACCR[DACEN], CMP_DACCR[VRSEL], CMP_DACCR[VOSEL], CMP_MUXCR[PSEL], and
CMP_MUXCR[MSEL]) and the comparator output settling to a stable level.
3. 1 LSB = Vreference/64
Peripheral operating requirements and behaviors
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 37
Freescale Semiconductor, Inc.
Figure 15. Typical hysteresis vs. Vin level (VDD = 3.3 V, PMODE = 0)
Peripheral operating requirements and behaviors
38 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
00
01
10
HYSTCTR
Setting
10
11
0.1 3.12.82.5
2.2
1.91.61.3
1
0.70.4
0.1
0
0.02
0.04
0.06
0.18
0.14
0.12
0.08
0.16
Vin level (V)
CMP Hysteresis (V)
Figure 16. Typical hysteresis vs. Vin level (VDD = 3.3 V, PMODE = 1)
3.6.3 12-bit DAC electrical characteristics
3.6.3.1 12-bit DAC operating requirements
Table 27. 12-bit DAC operating requirements
Symbol Desciption Min. Max. Unit Notes
VDDA Supply voltage 1.71 3.6 V
VDACR Reference voltage 1.13 3.6 V 1
CLOutput load capacitance 100 pF 2
ILOutput load current 1 mA
1. The DAC reference can be selected to be VDDA or VREFH.
2. A small load capacitance (47 pF) can improve the bandwidth performance of the DAC.
Peripheral operating requirements and behaviors
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 39
Freescale Semiconductor, Inc.
3.6.3.2 12-bit DAC operating behaviors
Table 28. 12-bit DAC operating behaviors
Symbol Description Min. Typ. Max. Unit Notes
IDDA_DACL
P
Supply current — low-power mode 330 μA
IDDA_DACH
P
Supply current — high-speed mode 1200 μA
tDACLP Full-scale settling time (0x080 to 0xF7F) —
low-power mode
100 200 μs 1
tDACHP Full-scale settling time (0x080 to 0xF7F) —
high-power mode
15 30 μs 1
tCCDACLP Code-to-code settling time (0xBF8 to
0xC08) — low-power mode and high-speed
mode
0.7 1 μs 1
Vdacoutl DAC output voltage range low — high-
speed mode, no load, DAC set to 0x000
100 mV
Vdacouth DAC output voltage range high — high-
speed mode, no load, DAC set to 0xFFF
VDACR
−100
VDACR mV
INL Integral non-linearity error — high speed
mode
±8 LSB 2
DNL Differential non-linearity error — VDACR > 2
V
±1 LSB 3
DNL Differential non-linearity error — VDACR =
VREF_OUT
±1 LSB 4
VOFFSET Offset error ±0.4 ±0.8 %FSR 5
EGGain error ±0.1 ±0.6 %FSR 5
PSRR Power supply rejection ratio, VDDA ≥ 2.4 V 60 90 dB
TCO Temperature coefficient offset voltage 3.7 μV/C 6
TGE Temperature coefficient gain error 0.000421 %FSR/C
Rop Output resistance (load = 3 kΩ) 250 Ω
SR Slew rate -80hF7Fh80h
High power (SPHP)
Low power (SPLP)
1.2
0.05
1.7
0.12
V/μs
BW 3dB bandwidth
High power (SPHP)
Low power (SPLP)
550
40
kHz
1. Settling within ±1 LSB
2. The INL is measured for 0 + 100 mV to VDACR −100 mV
3. The DNL is measured for 0 + 100 mV to VDACR −100 mV
4. The DNL is measured for 0 + 100 mV to VDACR −100 mV with VDDA > 2.4 V
5. Calculated by a best fit curve from VSS + 100 mV to VDACR − 100 mV
6. VDDA = 3.0 V, reference select set for VDDA (DACx_CO:DACRFS = 1), high power mode (DACx_C0:LPEN = 0), DAC set
to 0x800, temperature range is across the full range of the device
Peripheral operating requirements and behaviors
40 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
Digital Code
DAC12 INL (LSB)
0
500 1000 1500 2000 2500 3000 3500 4000
2
4
6
8
-2
-4
-6
-8
0
Figure 17. Typical INL error vs. digital code
Peripheral operating requirements and behaviors
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 41
Freescale Semiconductor, Inc.
Temperature °C
DAC12 Mid Level Code Voltage
25 55 85 105 125
1.499
-40
1.4985
1.498
1.4975
1.497
1.4965
1.496
Figure 18. Offset at half scale vs. temperature
3.6.4 Voltage reference electrical specifications
Table 29. VREF full-range operating requirements
Symbol Description Min. Max. Unit Notes
VDDA Supply voltage 1.71 3.6 V
TATemperature Operating temperature
range of the device
°C
CLOutput load capacitance 100 nF 1, 2
1. CL must be connected to VREF_OUT if the VREF_OUT functionality is being used for either an internal or external
reference.
2. The load capacitance should not exceed +/-25% of the nominal specified CL value over the operating temperature range
of the device.
Peripheral operating requirements and behaviors
42 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
Table 30. VREF full-range operating behaviors
Symbol Description Min. Typ. Max. Unit Notes
Vout Voltage reference output with factory trim at
nominal VDDA and temperature=25°C
1.1920 1.1950 1.1980 V 1
Vout Voltage reference output with user trim at
nominal VDDA and temperature=25°C
1.1945 1.1950 1.1955 V 1
Vstep Voltage reference trim step 0.5 mV 1
Vtdrift Temperature drift (Vmax -Vmin across the full
temperature range)
15 mV 1
Ibg Bandgap only current 80 µA
Ilp Low-power buffer current 360 uA 1
Ihp High-power buffer current 1 mA 1
ΔVLOAD Load regulation
current = ± 1.0 mA
200
µV 1, 2
Tstup Buffer startup time 100 µs
Tchop_osc_st
up
Internal bandgap start-up delay with chop
oscillator enabled
35 ms
Vvdrift Voltage drift (Vmax -Vmin across the full
voltage range)
2 mV 1
1. See the chip's Reference Manual for the appropriate settings of the VREF Status and Control register.
2. Load regulation voltage is the difference between the VREF_OUT voltage with no load vs. voltage with defined load
Table 31. VREF limited-range operating requirements
Symbol Description Min. Max. Unit Notes
TATemperature 0 70 °C
Table 32. VREF limited-range operating behaviors
Symbol Description Min. Max. Unit Notes
Vtdrift Temperature drift (Vmax -Vmin across the limited
temperature range)
10 mV
3.7 Timers
See General switching specifications.
3.8 Communication interfaces
Peripheral operating requirements and behaviors
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 43
Freescale Semiconductor, Inc.
3.8.1 DSPI switching specifications (limited voltage range)
The Deserial Serial Peripheral Interface (DSPI) provides a synchronous serial bus with
master and slave operations. Many of the transfer attributes are programmable. The
tables below provide DSPI timing characteristics for classic SPI timing modes. Refer to
the SPI chapter of the Reference Manual for information on the modified transfer
formats used for communicating with slower peripheral devices.
Table 33. Master mode DSPI timing (limited voltage range)
Num Description Min. Max. Unit Notes
Operating voltage 2.7 3.6 V
Frequency of operation 30 MHz
DS1 DSPI_SCK output cycle time 2 x tBUS ns
DS2 DSPI_SCK output high/low time (tSCK/2) − 2 (tSCK/2) + 2 ns
DS3 DSPI_PCSn valid to DSPI_SCK delay (tBUS x 2) −
2
ns 1
DS4 DSPI_SCK to DSPI_PCSn invalid delay (tBUS x 2) −
2
ns 2
DS5 DSPI_SCK to DSPI_SOUT valid 8.5 ns
DS6 DSPI_SCK to DSPI_SOUT invalid -2 ns
DS7 DSPI_SIN to DSPI_SCK input setup 16.2 ns
DS8 DSPI_SCK to DSPI_SIN input hold 0 ns
1. The delay is programmable in SPIx_CTARn[PSSCK] and SPIx_CTARn[CSSCK].
2. The delay is programmable in SPIx_CTARn[PASC] and SPIx_CTARn[ASC].
DS3 DS4
DS1
DS2
DS7 DS8
First data Last data
DS5
First data Data Last data
DS6
Data
DSPI_PCSn
DSPI_SCK
(CPOL=0)
DSPI_SIN
DSPI_SOUT
Figure 19. DSPI classic SPI timing — master mode
Peripheral operating requirements and behaviors
44 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
Table 34. Slave mode DSPI timing (limited voltage range)
Num Description Min. Max. Unit Notes
Operating voltage 2.7 3.6 V
Frequency of operation 15 MHz 1
DS9 DSPI_SCK input cycle time 4 x tBUS ns
DS10 DSPI_SCK input high/low time (tSCK/2) − 2 (tSCK/2) + 2 ns
DS11 DSPI_SCK to DSPI_SOUT valid 21.4 ns
DS12 DSPI_SCK to DSPI_SOUT invalid 0 ns
DS13 DSPI_SIN to DSPI_SCK input setup 2.6 ns
DS14 DSPI_SCK to DSPI_SIN input hold 7 ns
DS15 DSPI_SS active to DSPI_SOUT driven 17 ns
DS16 DSPI_SS inactive to DSPI_SOUT not driven 17 ns
1. The maximum operating frequency is measured with noncontinuous CS and SCK. When DSPI is configured with
continuous CS and SCK, the SPI clock must not be greater than 1/6 of the bus clock. For example, when the bus
clock is 60 MHz, the SPI clock must not be greater than 10 MHz.
First data Last data
First data Data Last data
Data
DS15
DS10 DS9
DS16
DS11
DS12
DS14
DS13
DSPI_SS
DSPI_SCK
(CPOL=0)
DSPI_SOUT
DSPI_SIN
Figure 20. DSPI classic SPI timing — slave mode
Peripheral operating requirements and behaviors
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 45
Freescale Semiconductor, Inc.
3.8.2 DSPI switching specifications (full voltage range)
The Deserial Serial Peripheral Interface (DSPI) provides a synchronous serial bus with
master and slave operations. Many of the transfer attributes are programmable. The
tables below provides DSPI timing characteristics for classic SPI timing modes. Refer
to the SPI chapter of the Reference Manual for information on the modified transfer
formats used for communicating with slower peripheral devices.
Table 35. Master mode DSPI timing (full voltage range)
Num Description Min. Max. Unit Notes
Operating voltage 1.71 3.6 V 1
Frequency of operation 15 MHz
DS1 DSPI_SCK output cycle time 4 x tBUS ns
DS2 DSPI_SCK output high/low time (tSCK/2) - 4 (tSCK/2) + 4 ns
DS3 DSPI_PCSn valid to DSPI_SCK delay (tBUS x 2) −
4
ns 2
DS4 DSPI_SCK to DSPI_PCSn invalid delay (tBUS x 2) −
4
ns 3
DS5 DSPI_SCK to DSPI_SOUT valid 10 ns
DS6 DSPI_SCK to DSPI_SOUT invalid -4.5 ns
DS7 DSPI_SIN to DSPI_SCK input setup 24.6 ns
DS8 DSPI_SCK to DSPI_SIN input hold 0 ns
1. The DSPI module can operate across the entire operating voltage for the processor, but to run across the full voltage
range the maximum frequency of operation is reduced.
2. The delay is programmable in SPIx_CTARn[PSSCK] and SPIx_CTARn[CSSCK].
3. The delay is programmable in SPIx_CTARn[PASC] and SPIx_CTARn[ASC].
DS3 DS4
DS1
DS2
DS7 DS8
First data Last data
DS5
First data Data Last data
DS6
Data
DSPI_PCSn
DSPI_SCK
(CPOL=0)
DSPI_SIN
DSPI_SOUT
Figure 21. DSPI classic SPI timing — master mode
Peripheral operating requirements and behaviors
46 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
Table 36. Slave mode DSPI timing (full voltage range)
Num Description Min. Max. Unit
Operating voltage 1.71 3.6 V
Frequency of operation 7.5 MHz
DS9 DSPI_SCK input cycle time 8 x tBUS ns
DS10 DSPI_SCK input high/low time (tSCK/2) - 4 (tSCK/2) + 4 ns
DS11 DSPI_SCK to DSPI_SOUT valid 29.5 ns
DS12 DSPI_SCK to DSPI_SOUT invalid 0 ns
DS13 DSPI_SIN to DSPI_SCK input setup 3.2 ns
DS14 DSPI_SCK to DSPI_SIN input hold 7 ns
DS15 DSPI_SS active to DSPI_SOUT driven 25 ns
DS16 DSPI_SS inactive to DSPI_SOUT not driven 25 ns
First data Last data
First data Data Last data
Data
DS15
DS10 DS9
DS16
DS11
DS12
DS14
DS13
DSPI_SS
DSPI_SCK
(CPOL=0)
DSPI_SOUT
DSPI_SIN
Figure 22. DSPI classic SPI timing — slave mode
3.8.3 Inter-Integrated Circuit Interface (I2C) timing
Table 37. I 2C timing
Characteristic Symbol Standard Mode Fast Mode Unit
Minimum Maximum Minimum Maximum
SCL Clock Frequency fSCL 0 100 0 4001kHz
Hold time (repeated) START condition.
After this period, the first clock pulse is
generated.
tHD; STA 4 0.6 µs
LOW period of the SCL clock tLOW 4.7 1.25 µs
HIGH period of the SCL clock tHIGH 4 0.6 µs
Set-up time for a repeated START
condition
tSU; STA 4.7 0.6 µs
Table continues on the next page...
Peripheral operating requirements and behaviors
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 47
Freescale Semiconductor, Inc.
Table 37. I 2C timing (continued)
Characteristic Symbol Standard Mode Fast Mode Unit
Minimum Maximum Minimum Maximum
Data hold time for I2C bus devices tHD; DAT 023.453040.92µs
Data set-up time tSU; DAT 2505 1003, 6 ns
Rise time of SDA and SCL signals tr 1000 20 +0.1Cb7300 ns
Fall time of SDA and SCL signals tf 300 20 +0.1Cb6300 ns
Set-up time for STOP condition tSU; STO 4 0.6 µs
Bus free time between STOP and
START condition
tBUF 4.7 1.3 µs
Pulse width of spikes that must be
suppressed by the input filter
tSP N/A N/A 0 50 ns
1. The maximum SCL Clock Frequency in Fast mode with maximum bus loading can only be achieved when using the
High drive pins across the full voltage range and when using the Normal drive pins and VDD ≥ 2.7 V.
2. The master mode I2C deasserts ACK of an address byte simultaneously with the falling edge of SCL. If no slaves
acknowledge this address byte, then a negative hold time can result, depending on the edge rates of the SDA and SCL
lines.
3. The maximum tHD; DAT must be met only if the device does not stretch the LOW period (tLOW) of the SCL signal.
4. Input signal Slew = 10 ns and Output Load = 50 pF
5. Set-up time in slave-transmitter mode is 1 IPBus clock period, if the TX FIFO is empty.
6. A Fast mode I2C bus device can be used in a Standard mode I2C bus system, but the requirement tSU; DAT ≥ 250 ns
must then be met. This is automatically the case if the device does not stretch the LOW period of the SCL signal. If such
a device does stretch the LOW period of the SCL signal, then it must output the next data bit to the SDA line trmax + tSU;
DAT = 1000 + 250 = 1250 ns (according to the Standard mode I2C bus specification) before the SCL line is released.
7. Cb = total capacitance of the one bus line in pF.
Table 38. I 2C 1 Mbps timing
Characteristic Symbol Minimum Maximum Unit
SCL Clock Frequency fSCL 0 11MHz
Hold time (repeated) START condition. After this
period, the first clock pulse is generated.
tHD; STA 0.26 µs
LOW period of the SCL clock tLOW 0.5 µs
HIGH period of the SCL clock tHIGH 0.26 µs
Set-up time for a repeated START condition tSU; STA 0.26 µs
Data hold time for I2C bus devices tHD; DAT 0 µs
Data set-up time tSU; DAT 50 ns
Rise time of SDA and SCL signals tr20 +0.1Cb, 2120 ns
Fall time of SDA and SCL signals tf20 +0.1Cb2120 ns
Set-up time for STOP condition tSU; STO 0.26 µs
Bus free time between STOP and START condition tBUF 0.5 µs
Pulse width of spikes that must be suppressed by
the input filter
tSP 0 50 ns
1. The maximum SCL clock frequency of 1 Mbps can support maximum bus loading when using the High drive pins across
the full voltage range.
2. Cb = total capacitance of the one bus line in pF.
Peripheral operating requirements and behaviors
48 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
SDA
HD; STA tHD; DAT
tLOW
tSU; DAT
tHIGH
tSU; STA SR PS
S
tHD; STA tSP
tSU; STO
tBUF
tftr
tftr
SCL
Figure 23. Timing definition for devices on the I2C bus
3.8.4 UART switching specifications
See General switching specifications.
3.9 Kinetis Motor Suite
Kinetis Motor Suite is a bundled software solution that enables the rapid configuration
of motor drive systems, and accelerates development of the final motor drive
application.
Several members of the KV3x family are enabled with Kinetis motor suite. The
enabled devices can be identified within the orderable part numbers in this table. For
more information refer to Kinetis Motor Suite User's Guide (KMS100UG) and Kinetis
Motor Suite API Reference Manual (KMS100RM).
NOTE
To find the associated resource, go to freescale.com and
perform a search using Document ID.
4Dimensions
4.1 Obtaining package dimensions
Package dimensions are provided in package drawings.
To find a package drawing, go to freescale.com and perform a keyword search for the
drawing’s document number:
Dimensions
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 49
Freescale Semiconductor, Inc.
If you want the drawing for this package Then use this document number
64-pin LQFP 98ASS23234W
100-pin LQFP 98ASS23308W
5 Pinout
5.1 KV31F Signal Multiplexing and Pin Assignments
The following table shows the signals available on each pin and the locations of these
pins on the devices supported by this document. The Port Control Module is responsible
for selecting which ALT functionality is available on each pin.
100
LQFP
64
LQFP
Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 ALT7 EzPort
1 1 PTE0/
CLKOUT32K
ADC1_SE4a ADC1_SE4a PTE0/
CLKOUT32K
SPI1_PCS1 UART1_TX I2C1_SDA
2 2 PTE1/
LLWU_P0
ADC1_SE5a ADC1_SE5a PTE1/
LLWU_P0
SPI1_SOUT UART1_RX I2C1_SCL SPI1_SIN
3 PTE2/
LLWU_P1
ADC1_SE6a ADC1_SE6a PTE2/
LLWU_P1
SPI1_SCK UART1_
CTS_b
4 PTE3 ADC1_SE7a ADC1_SE7a PTE3 SPI1_SIN UART1_
RTS_b
SPI1_SOUT
5 PTE4/
LLWU_P2
DISABLED PTE4/
LLWU_P2
SPI1_PCS0 LPUART0_
TX
6 PTE5 DISABLED PTE5 SPI1_PCS2 LPUART0_
RX
7 PTE6 DISABLED PTE6 SPI1_PCS3 LPUART0_
CTS_b
8 3 VDD VDD VDD
9 4 VSS VSS VSS
10 5 PTE16 ADC0_SE4a ADC0_SE4a PTE16 SPI0_PCS0 UART2_TX FTM_CLKIN0 FTM0_FLT3
11 6 PTE17 ADC0_SE5a ADC0_SE5a PTE17 SPI0_SCK UART2_RX FTM_CLKIN1 LPTMR0_
ALT3
12 7 PTE18 ADC0_SE6a ADC0_SE6a PTE18 SPI0_SOUT UART2_
CTS_b
I2C0_SDA
13 8 PTE19 ADC0_SE7a ADC0_SE7a PTE19 SPI0_SIN UART2_
RTS_b
I2C0_SCL
14 ADC0_DP1 ADC0_DP1 ADC0_DP1
15 ADC0_DM1 ADC0_DM1 ADC0_DM1
16 ADC1_DP1/
ADC0_DP2
ADC1_DP1/
ADC0_DP2
ADC1_DP1/
ADC0_DP2
Pinout
50 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
100
LQFP
64
LQFP
Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 ALT7 EzPort
17 ADC1_DM1/
ADC0_DM2
ADC1_DM1/
ADC0_DM2
ADC1_DM1/
ADC0_DM2
18 9 ADC0_DP0/
ADC1_DP3
ADC0_DP0/
ADC1_DP3
ADC0_DP0/
ADC1_DP3
19 10 ADC0_DM0/
ADC1_DM3
ADC0_DM0/
ADC1_DM3
ADC0_DM0/
ADC1_DM3
20 11 ADC1_DP0/
ADC0_DP3
ADC1_DP0/
ADC0_DP3
ADC1_DP0/
ADC0_DP3
21 12 ADC1_DM0/
ADC0_DM3
ADC1_DM0/
ADC0_DM3
ADC1_DM0/
ADC0_DM3
22 13 VDDA VDDA VDDA
23 14 VREFH VREFH VREFH
24 15 VREFL VREFL VREFL
25 16 VSSA VSSA VSSA
26 17 VREF_OUT/
CMP1_IN5/
CMP0_IN5/
ADC1_SE18
VREF_OUT/
CMP1_IN5/
CMP0_IN5/
ADC1_SE18
VREF_OUT/
CMP1_IN5/
CMP0_IN5/
ADC1_SE18
27 18 DAC0_OUT/
CMP1_IN3/
ADC0_SE23
DAC0_OUT/
CMP1_IN3/
ADC0_SE23
DAC0_OUT/
CMP1_IN3/
ADC0_SE23
28 19 CMP0_IN4/
ADC1_SE23
CMP0_IN4/
ADC1_SE23
CMP0_IN4/
ADC1_SE23
29 VSS VSS VSS
30 VDD VDD VDD
31 20 PTE24 ADC0_SE17 ADC0_SE17 PTE24 FTM0_CH0 I2C0_SCL EWM_OUT_
b
32 21 PTE25 ADC0_SE18 ADC0_SE18 PTE25 FTM0_CH1 I2C0_SDA EWM_IN
33 PTE26/
CLKOUT32K
DISABLED PTE26/
CLKOUT32K
34 22 PTA0 JTAG_TCLK/
SWD_CLK/
EZP_CLK
PTA0 UART0_
CTS_b
FTM0_CH5 EWM_IN JTAG_TCLK/
SWD_CLK
EZP_CLK
35 23 PTA1 JTAG_TDI/
EZP_DI
PTA1 UART0_RX FTM0_CH6 CMP0_OUT FTM2_QD_
PHA
FTM1_CH1 JTAG_TDI EZP_DI
36 24 PTA2 JTAG_TDO/
TRACE_
SWO/
EZP_DO
PTA2 UART0_TX FTM0_CH7 CMP1_OUT FTM2_QD_
PHB
FTM1_CH0 JTAG_TDO/
TRACE_
SWO
EZP_DO
37 25 PTA3 JTAG_TMS/
SWD_DIO
PTA3 UART0_
RTS_b
FTM0_CH0 FTM2_FLT0 EWM_OUT_
b
JTAG_TMS/
SWD_DIO
38 26 PTA4/
LLWU_P3
NMI_b/
EZP_CS_b
PTA4/
LLWU_P3
FTM0_CH1 FTM0_FLT3 NMI_b EZP_CS_b
39 27 PTA5 DISABLED PTA5 FTM0_CH2 JTAG_
TRST_b
40 VDD VDD VDD
Pinout
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 51
Freescale Semiconductor, Inc.
100
LQFP
64
LQFP
Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 ALT7 EzPort
41 VSS VSS VSS
42 28 PTA12 DISABLED PTA12 FTM1_CH0 FTM1_QD_
PHA
43 29 PTA13/
LLWU_P4
DISABLED PTA13/
LLWU_P4
FTM1_CH1 FTM1_QD_
PHB
44 PTA14 DISABLED PTA14 SPI0_PCS0 UART0_TX
45 PTA15 DISABLED PTA15 SPI0_SCK UART0_RX
46 PTA16 DISABLED PTA16 SPI0_SOUT UART0_
CTS_b
47 PTA17 ADC1_SE17 ADC1_SE17 PTA17 SPI0_SIN UART0_
RTS_b
48 30 VDD VDD VDD
49 31 VSS VSS VSS
50 32 PTA18 EXTAL0 EXTAL0 PTA18 FTM0_FLT2 FTM_CLKIN0
51 33 PTA19 XTAL0 XTAL0 PTA19 FTM0_FLT0 FTM1_FLT0 FTM_CLKIN1 LPTMR0_
ALT1
52 34 RESET_b RESET_b RESET_b
53 35 PTB0/
LLWU_P5
ADC0_SE8/
ADC1_SE8
ADC0_SE8/
ADC1_SE8
PTB0/
LLWU_P5
I2C0_SCL FTM1_CH0 FTM1_QD_
PHA
UART0_RX
54 36 PTB1 ADC0_SE9/
ADC1_SE9
ADC0_SE9/
ADC1_SE9
PTB1 I2C0_SDA FTM1_CH1 FTM0_FLT2 EWM_IN FTM1_QD_
PHB
UART0_TX
55 37 PTB2 ADC0_SE12 ADC0_SE12 PTB2 I2C0_SCL UART0_
RTS_b
FTM0_FLT1 FTM0_FLT3
56 38 PTB3 ADC0_SE13 ADC0_SE13 PTB3 I2C0_SDA UART0_
CTS_b
FTM0_FLT0
57 PTB9 DISABLED PTB9 SPI1_PCS1 LPUART0_
CTS_b
58 PTB10 ADC1_SE14 ADC1_SE14 PTB10 SPI1_PCS0 LPUART0_
RX
FTM0_FLT1
59 PTB11 ADC1_SE15 ADC1_SE15 PTB11 SPI1_SCK LPUART0_
TX
FTM0_FLT2
60 VSS VSS VSS
61 VDD VDD VDD
62 39 PTB16 DISABLED PTB16 SPI1_SOUT UART0_RX FTM_CLKIN0 EWM_IN
63 40 PTB17 DISABLED PTB17 SPI1_SIN UART0_TX FTM_CLKIN1 EWM_OUT_
b
64 41 PTB18 DISABLED PTB18 FTM2_CH0 FTM2_QD_
PHA
65 42 PTB19 DISABLED PTB19 FTM2_CH1 FTM2_QD_
PHB
66 PTB20 DISABLED PTB20 CMP0_OUT
67 PTB21 DISABLED PTB21 CMP1_OUT
68 PTB22 DISABLED PTB22
69 PTB23 DISABLED PTB23 SPI0_PCS5
Pinout
52 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
100
LQFP
64
LQFP
Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 ALT7 EzPort
70 43 PTC0 ADC0_SE14 ADC0_SE14 PTC0 SPI0_PCS4 PDB0_
EXTRG
FTM0_FLT1 SPI0_PCS0
71 44 PTC1/
LLWU_P6
ADC0_SE15 ADC0_SE15 PTC1/
LLWU_P6
SPI0_PCS3 UART1_
RTS_b
FTM0_CH0 LPUART0_
RTS_b
72 45 PTC2 ADC0_SE4b/
CMP1_IN0
ADC0_SE4b/
CMP1_IN0
PTC2 SPI0_PCS2 UART1_
CTS_b
FTM0_CH1 LPUART0_
CTS_b
73 46 PTC3/
LLWU_P7
CMP1_IN1 CMP1_IN1 PTC3/
LLWU_P7
SPI0_PCS1 UART1_RX FTM0_CH2 CLKOUT LPUART0_
RX
74 47 VSS VSS VSS
75 48 VDD VDD VDD
76 49 PTC4/
LLWU_P8
DISABLED PTC4/
LLWU_P8
SPI0_PCS0 UART1_TX FTM0_CH3 CMP1_OUT LPUART0_
TX
77 50 PTC5/
LLWU_P9
DISABLED PTC5/
LLWU_P9
SPI0_SCK LPTMR0_
ALT2
CMP0_OUT FTM0_CH2
78 51 PTC6/
LLWU_P10
CMP0_IN0 CMP0_IN0 PTC6/
LLWU_P10
SPI0_SOUT PDB0_
EXTRG
I2C0_SCL
79 52 PTC7 CMP0_IN1 CMP0_IN1 PTC7 SPI0_SIN I2C0_SDA
80 53 PTC8 ADC1_SE4b/
CMP0_IN2
ADC1_SE4b/
CMP0_IN2
PTC8
81 54 PTC9 ADC1_SE5b/
CMP0_IN3
ADC1_SE5b/
CMP0_IN3
PTC9 FTM2_FLT0
82 55 PTC10 ADC1_SE6b ADC1_SE6b PTC10 I2C1_SCL
83 56 PTC11/
LLWU_P11
ADC1_SE7b ADC1_SE7b PTC11/
LLWU_P11
I2C1_SDA
84 PTC12 DISABLED PTC12
85 PTC13 DISABLED PTC13
86 PTC14 DISABLED PTC14
87 PTC15 DISABLED PTC15
88 VSS VSS VSS
89 VDD VDD VDD
90 PTC16 DISABLED PTC16 LPUART0_
RX
91 PTC17 DISABLED PTC17 LPUART0_
TX
92 PTC18 DISABLED PTC18 LPUART0_
RTS_b
93 57 PTD0/
LLWU_P12
DISABLED PTD0/
LLWU_P12
SPI0_PCS0 UART2_
RTS_b
FTM0_CH0 LPUART0_
RTS_b
94 58 PTD1 ADC0_SE5b ADC0_SE5b PTD1 SPI0_SCK UART2_
CTS_b
FTM0_CH1 LPUART0_
CTS_b
95 59 PTD2/
LLWU_P13
DISABLED PTD2/
LLWU_P13
SPI0_SOUT UART2_RX FTM0_CH2 LPUART0_
RX
I2C0_SCL
96 60 PTD3 DISABLED PTD3 SPI0_SIN UART2_TX FTM0_CH3 LPUART0_
TX
I2C0_SDA
Pinout
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 53
Freescale Semiconductor, Inc.
100
LQFP
64
LQFP
Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 ALT7 EzPort
97 61 PTD4/
LLWU_P14
DISABLED PTD4/
LLWU_P14
SPI0_PCS1 UART0_
RTS_b
FTM0_CH4 EWM_IN SPI1_PCS0
98 62 PTD5 ADC0_SE6b ADC0_SE6b PTD5 SPI0_PCS2 UART0_
CTS_b
FTM0_CH5 EWM_OUT_
b
SPI1_SCK
99 63 PTD6/
LLWU_P15
ADC0_SE7b ADC0_SE7b PTD6/
LLWU_P15
SPI0_PCS3 UART0_RX FTM0_CH6 FTM0_FLT0 SPI1_SOUT
100 64 PTD7 DISABLED PTD7 UART0_TX FTM0_CH7 FTM0_FLT1 SPI1_SIN
5.2 Recommended connection for unused analog and digital
pins
The following table shows the recommended connections for analog interface pins if
those analog interfaces are not used in the customer's application.
Table 39. Recommended connection for unused analog interfaces
Pin Type Short recommendation Detailed recommendation
Analog/non GPIO PGAx/ADCx Float Analog input - Float
Analog/non GPIO ADCx/CMPx Float Analog input - Float
Analog/non GPIO VREF_OUT Float Analog output - Float
Analog/non GPIO DACx_OUT Float Analog output - Float
Analog/non GPIO RTC_WAKEUP_B Float Analog output - Float
Analog/non GPIO XTAL32 Float Analog output - Float
Analog/non GPIO EXTAL32 Float Analog input - Float
GPIO/Analog PTA18/EXTAL0 Float Analog input - Float
GPIO/Analog PTA19/XTAL0 Float Analog output - Float
GPIO/Analog PTx/ADCx Float Float (default is analog input)
GPIO/Analog PTx/CMPx Float Float (default is analog input)
GPIO/Digital PTA0/JTAG_TCLK Float Float (default is JTAG with
pulldown)
GPIO/Digital PTA1/JTAG_TDI Float Float (default is JTAG with
pullup)
GPIO/Digital PTA2/JTAG_TDO Float Float (default is JTAG with
pullup)
GPIO/Digital PTA3/JTAG_TMS Float Float (default is JTAG with
pullup)
GPIO/Digital PTA4/NMI_b 10kΩ pullup or disable and
float
Pull high or disable in PCR &
FOPT and float
GPIO/Digital PTx Float Float (default is disabled)
VDDA VDDA Always connect to VDD
potential
Always connect to VDD
potential
Table continues on the next page...
Pinout
54 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
Table 39. Recommended connection for unused analog interfaces (continued)
Pin Type Short recommendation Detailed recommendation
VREFH VREFH Always connect to VDD
potential
Always connect to VDD
potential
VREFL VREFL Always connect to VSS
potential
Always connect to VSS
potential
VSSA VSSA Always connect to VSS
potential
Always connect to VSS
potential
5.3 KV31F Pinouts
The following figure shows the pinout diagram for the devices supported by this
document. Many signals may be multiplexed onto a single pin. To determine what
signals can be used on which pin, see the previous section.
Pinout
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 55
Freescale Semiconductor, Inc.
PTE24
CMP0_IN4/ADC1_SE23
DAC0_OUT/CMP1_IN3/ADC0_SE23
VREF_OUT/CMP1_IN5/CMP0_IN5/ADC1_SE18
VSSA
VREFL
VREFH
VDDA
ADC1_DM0/ADC0_DM3
ADC1_DP0/ADC0_DP3
ADC0_DM0/ADC1_DM3
ADC0_DP0/ADC1_DP3
PTE19
PTE18
PTE17
PTE16
VSS
VDD
PTE1/LLWU_P0
PTE0/CLKOUT32K
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
64
63
62
61
PTD7
PTD6/LLWU_P15
PTD5
PTD4/LLWU_P14
PTD3
PTD2/LLWU_P13
PTD1
PTD0/LLWU_P12
PTC11/LLWU_P11
PTC10
PTC9
PTC8
PTC7
PTC6/LLWU_P10
PTC5/LLWU_P9
PTC4/LLWU_P8
VDD
VSS
PTC3/LLWU_P7
PTC2
PTC1/LLWU_P6
PTC0
PTB19
PTB18
PTB17
PTB16
PTB3
PTB2
PTB1
PTB0/LLWU_P5
RESET_b
PTA19
PTA18
VSS
VDD
PTA13/LLWU_P4
PTA12
PTA5
PTA4/LLWU_P3
PTA3
PTA2
PTA1
PTA0
PTE25
Figure 24. KV31F 64 LQFP pinout diagram (top view)
Pinout
56 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
60
59
58
57
56
55
54
53
52
51
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
ADC1_DP0/ADC0_DP3
ADC0_DM0/ADC1_DM3
ADC0_DP0/ADC1_DP3
ADC1_DM1/ADC0_DM2
ADC1_DP1/ADC0_DP2
ADC0_DM1
ADC0_DP1
PTE19
PTE18
PTE17
PTE16
VSS
VDD
PTE6
PTE5
PTE4/LLWU_P2
PTE3
PTE2/LLWU_P1
PTE1/LLWU_P0
PTE0/CLKOUT32K 75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
VDD
VSS
PTC3/LLWU_P7
PTC2
PTC1/LLWU_P6
PTC0
PTB23
PTB22
PTB21
PTB20
PTB19
PTB18
PTB17
PTB16
VDD
VSS
PTB11
PTB10
PTB9
PTB3
PTB2
PTB1
PTB0/LLWU_P5
RESET_b
PTA19
25
24
23
22
21
VSSA
VREFL
VREFH
VDDA
ADC1_DM0/ADC0_DM3
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
99
79
78
77
76
PTD6/LLWU_P15
PTC7
PTC6/LLWU_P10
PTC5/LLWU_P9
PTC4/LLWU_P8
50
49
48
47
46
45
44
43
42
41
PTA18
VSS
VDD
PTA17
PTA16
PTA15
PTA14
PTA13/LLWU_P4
PTA12
VSS
VDD
PTA5
PTA4/LLWU_P3
PTA3
PTA2
PTA1
PTA0
PTE26/CLKOUT32K
PTE25
PTE24
VDD
VSS
CMP0_IN4/ADC1_SE23
DAC0_OUT/CMP1_IN3/ADC0_SE23
VREF_OUT/CMP1_IN5/CMP0_IN5/ADC1_SE18
98 PTD5
97 PTD4/LLWU_P14
96 PTD3
95 PTD2/LLWU_P13
94 PTD1
93 PTD0/LLWU_P12
92 PTC18
91 PTC17
90 PTC16
89 VDD
88 VSS
80 PTC8
PTC9
PTC10
81
82
83 PTC11/LLWU_P11
84 PTC12
85 PTC13
86 PTC14
87 PTC15
100 PTD7
Figure 25. KV31F 100 LQFP pinout diagram (top view)
6Part identification
Part identification
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 57
Freescale Semiconductor, Inc.
6.1 Description
Part numbers for the chip have fields that identify the specific part. You can use the
values of these fields to determine the specific part you have received.
6.2 Format
Part numbers for this device have the following format:
Q KV## A FFF R T PP CC S N
6.3 Fields
This table lists the possible values for each field in the part number (not all
combinations are valid):
Field Description Values
Q Qualification status M = Fully qualified, general market flow
P = Prequalification
KV## Kinetis V Series KV3x: Cortex-M4 based MCU
A Key attribute D = Cortex-M4 w/ DSP
F = Cortex-M4 w/ DSP and FPU
FFF Program flash memory size 64 = 64 KB
128 = 128 KB
256 = 256 KB
512 = 512 KB
R Silicon revision (Blank) = Main
A = Revision after main
T Temperature range (°C) V = –40 to 105
C = –40 to 85
PP Package identifier FM = 32 QFN (5 mm x 5 mm)
LF = 48 LQFP (7 mm x 7 mm)
LH = 64 LQFP (10 mm x 10 mm)
LL = 100 LQFP (14 mm x 14 mm)
MC = 121 XFBGA (8 mm x 8 mm)
DC = 121 XFBGA (8 mm x 8 mm x 0.5 mm)
CC Maximum CPU frequency (MHz) 10 = 100 MHz
12 = 120 MHz
S Software type P = KMS-PMSM and BLDC
(Blank) = Not software enabled
N Packaging type R = Tape and reel
(Blank) = Trays
Part identification
58 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
6.4 Example
This is an example part number:
MKV31F256VLL12P
7 Terminology and guidelines
7.1 Definitions
Key terms are defined in the following table:
Term Definition
Rating A minimum or maximum value of a technical characteristic that, if exceeded, may cause
permanent chip failure:
Operating ratings apply during operation of the chip.
Handling ratings apply when the chip is not powered.
NOTE: The likelihood of permanent chip failure increases rapidly as soon as a characteristic
begins to exceed one of its operating ratings.
Operating requirement A specified value or range of values for a technical characteristic that you must guarantee during
operation to avoid incorrect operation and possibly decreasing the useful life of the chip
Operating behavior A specified value or range of values for a technical characteristic that are guaranteed during
operation if you meet the operating requirements and any other specified conditions
Typical value A specified value for a technical characteristic that:
Lies within the range of values specified by the operating behavior
Is representative of that characteristic during operation when you meet the typical-value
conditions or other specified conditions
NOTE: Typical values are provided as design guidelines and are neither tested nor
guaranteed.
Terminology and guidelines
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 59
Freescale Semiconductor, Inc.
7.2 Examples
Operating rating:
Operating requirement:
Operating behavior that includes a typical value:
EXAMPLE
EXAMPLEEXAMPLE
EXAMPLE
7.3 Typical-value conditions
Typical values assume you meet the following conditions (or other conditions as
specified):
Symbol Description Value Unit
TAAmbient temperature 25 °C
VDD Supply voltage 3.3 V
Terminology and guidelines
60 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
7.4 Relationship between ratings and operating requirements
- No permanent failure
- Correct operation
Normal operating range
Fatal range
Expected permanent failure
Fatal range
Expected permanent failure
Operating rating (max.)
Operating requirement (max.)
Operating requirement (min.)
Operating rating (min.)
Operating (power on)
Degraded operating range Degraded operating range
No permanent failure
Handling range
Fatal range
Expected permanent failure
Fatal range
Expected permanent failure
Handling rating (max.)
Handling rating (min.)
Handling (power off)
- No permanent failure
- Possible decreased life
- Possible incorrect operation
- No permanent failure
- Possible decreased life
- Possible incorrect operation
7.5 Guidelines for ratings and operating requirements
Follow these guidelines for ratings and operating requirements:
Never exceed any of the chip’s ratings.
During normal operation, don’t exceed any of the chip’s operating requirements.
If you must exceed an operating requirement at times other than during normal
operation (for example, during power sequencing), limit the duration as much as
possible.
8Revision History
The following table provides a revision history for this document.
Table 40. Revision History
Rev. No. Date Substantial Changes
7 02/2016 Added Terminology and Guideline section
Updated Front matter section
Added KMS related information in front matter
Added Kinetis Motor Suite section
Added "S" in Format and Part Identification table
Table continues on the next page...
Revision History
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 61
Freescale Semiconductor, Inc.
Table 40. Revision History (continued)
Rev. No. Date Substantial Changes
Updated the Part Number Example
Updated IRC48M specifications table
6 10/2015 In "Power consumption operating behaviors" section, added "Low power mode
peripheral adders—typical value" table
In "Thermal operating requirements" table, in footnote, corrected "TJ = TA + ΘJA" to
"TJ = TA + RΘJA"
Updated "IRC48M specifications" table
Updated "NVM program/erase timing specifications" table; updated values for
thversall (Erase All high-voltage time)
In "Slave mode DSPI timing (limited voltage range)" table, added footnote regarding
maximum frequency of operation
Added new section, "Recommended connections for unused analog and digital
pins"
5 4/2015 Throughout: Removed notes stating that the 64-pin MAPBGA package for this
product is not yet available
On page 1:
Under "Security and integrity modules" added "Hardware random-number
generator"
Under "Communication interfaces," updated I2C bullet to indicate support for
up to 1 Mbps operation
Under "Operating characteristics," specified that voltage range includes flash
writes
In figure, "Functional block diagram," added "Random-number generator" and
"Flash access control"
In "Voltage and current operating requirements" table:
Removed content related to positive injection
Updated footnote 1 to say that all analog and I/O pins are internally clamped
to VSS only (not VSS and VDD)through ESD protection diodes.
In "Power consumption operating behaviors" table:
Added additional temperature data in power consumption table
Added Max IDD values based on characterization results equivalent to mean
+ 3 sigma
Updated "EMC radiated emissions operating behaviors" table
In "Thermal operating requirements" table, added the following footnote for ambient
temperature: "Maximum TA can be exceeded only if the user ensures that TJ does
not exceed maximum TJ. The simplest method to determine TJ is: TJ = TA + ΘJA x
chip power dissipation"
Updated "IRC48M Specifications":
Updated maximum values for Δfirc48m_lv and Δfirc48m_hv (full temperature)
Added specifications for Δfirc48m_hv (-40°C to 85°C)
In "I2C timing" table,
Added the following footnote on maximum Fast mode value for SCL Clock
Frequency: "The maximum SCL Clock Frequency in Fast mode with
maximum bus loading can only be achieved when using the High drive pins
across the full voltage range and when using the Normal drive pins and VDD
≥ 2.7 V."
Updated minimum Fast mode value for LOW period of the SCL clock to 1.25 µ
Added "I2C 1 Mbps timing" table
Specified that the figure, "KV31F 64 LQFP Pinout Diagram" is a top view
Specified that the figure, "KV31F 100 LQFP Pinout Diagram" is a top view
Removed Section 6, "Ordering parts."
47/2014 In "Power consumption operating behaviors table":
Table continues on the next page...
Revision History
62 Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016
Freescale Semiconductor, Inc.
Table 40. Revision History (continued)
Rev. No. Date Substantial Changes
Updated existing typical power measurements
Added new typical power measurements for the following:
IDD_HSRUN (High Speed Run mode current executing CoreMark code)
IDD_RUNCO (Run mode current in Compute operation, executing
CoreMark code)
IDD_RUN (Run mode current in Compute operation, executing while(1)
loop)
IDD_VLPR (Very Low Power mode current executing CoreMark code)
IDD_VLPR (Very Low Power Run mode current in Compute operation,
executing while(1) loop)
3 7/2014 On p. 1:
Updated introduction
Under "Memories and memory interfaces," added bullet, "Pre-programmed
Kinetis flashloader for one-time, in-system factory programming"
Under "Security and integrity modules," added bullet, "Hardware random-
number generator"
In "Voltage and current operating ratings" table, updated maximum digital supply
current
Updated "Voltage and current operating behaviors" table
Updated "Power mode transition operating behaviors" table
Updated "Power consumption operating behaviors" table
Updated figure, "Run Mode Current vs Core Frequency"
Updated figure, "Very Low Power Run (VLPR) Current vs Core Frequency"
Updated "EMC radiated emissions operating behaviors for 64 LQFP package" table
Updated "Thermal attributes" table
Updated "MCG specifications" table
Updated "IRC48M specifications" table
Updated "16-bit ADC operating conditions" table
Updated "Voltage reference electrical specifications" section
23/2014 Initial public release
Revision History
Kinetis KV31F 256 KB Flash, Rev. 7, 02/2016 63
Freescale Semiconductor, Inc.
How to Reach Us:
Home Page:
freescale.com
Web Support:
freescale.com/support
Information in this document is provided solely to enable system and
software implementers to use Freescale products. There are no express
or implied copyright licenses granted hereunder to design or fabricate
any integrated circuits based on the information in this document.
Freescale reserves the right to make changes without further notice to
any products herein.
Freescale makes no warranty, representation, or guarantee regarding
the suitability of its products for any particular purpose, nor does
Freescale assume any liability arising out of the application or use of
any product or circuit, and specifically disclaims any and all liability,
including without limitation consequential or incidental damages.
“Typical” parameters that may be provided in Freescale data sheets
and/or specifications can and do vary in different applications, and
actual performance may vary over time. All operating parameters,
including “typicals,” must be validated for each customer application by
customer's technical experts. Freescale does not convey any license
under its patent rights nor the rights of others. Freescale sells products
pursuant to standard terms and conditions of sale, which can be found
at the following address: freescale.com/SalesTermsandConditions.
Freescale, the Freescale logo, and Kinetis are trademarks of Freescale
Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. All other product or
service names are the property of their respective owners. ARM, ARM
Powered logo, and Cortex are registered trademarks of ARM Limited (or
its subsidiaries) in the EU and/or elsewhere. SpinTAC is a trademark of
LineStream Technologies, Inc. All rights reserved.
© 2014–2016 Freescale Semiconductor, Inc.
Document Number KV31P100M120SF8
Revision 7, 02/2016