SCHOTTKY RECTIFIER 3 Amp
30BQ040
Bulletin PD-2.439 rev. F 03/03
1
www.irf.com
Major Ratings and Characteristics
IF(AV) Rectangular 3.0 A
waveform
VRRM 40 V
IFSM @ t p= 5 µs sine 2000 A
VF@ 3.0 Apk, TJ = 125°C 0.43 V
TJrange - 55 to 150 °C
Characteristics 30BQ040 Units The 30BQ040 surface-mount Schottky rectifier has been de-
signed for applications requiring low forward drop and small
foot prints on PC boards. Typical applications are in disk drives,
switching power supplies, converters, free-wheeling diodes,
battery charging, and reverse battery protection.
Small foot print, surface mountable
Very low forward voltage drop
High frequency operation
Guard ring for enhanced ruggedness and long term
reliability
Description/ Features
SMC
Outline SMC
Dimensions in millimeters and (inches)
For recommended footprint and soldering techniques refer to Application Note # AN-994
5.59 (.220)
6.22 (.245)
6.60 (.260)
7.11 (.280)
2.75 (.108)
3.15 (.124)
.152 (.006)
.305 (.012)
2.00 (.079)
2.62 (.103)
0.76 (.030)
1.52 (.060)
.102 (.004)
.203 (.008)
7.75 (.305)
8.13 (.320)
Device Marking: IR3F
CATHODE ANODE
1 2
12
POLARIT Y PART NUMBER
30BQ040
Bulletin PD-2.439 rev. F 03/03
2www.irf.com
Parameters 30BQ Units Conditions
VFM Max. Forward Voltage Drop (1) 0.53 V @ 3A
0.68 V @ 6A
0.43 V @ 3A
0.57 V @ 6A
IRM Max. Reverse Leakage Current (1) 0.5 mA TJ = 25 °C
30 mA TJ = 125 °C
CTMax. Junction Capacitance 230 pF VR = 5VDC (test signal range 100KHz to 1Mhz) 25°C
LSTypical Series Inductance 3.0 nH Measured lead to lead 5mm from package body
dv/dt Max. Voltage Rate of Change 10000 V/µs (Rated V R)
Part number 30BQ040
VRMax. DC Reverse Voltage (V) 40
VRWM Max. Working Peak Reverse Voltage (V)
Voltage Ratings
IF(AV) Max. Average Forward Current 3.0 A 50% duty cycle @ TL = 118 °C, rectangular wave form
4.0 50% duty cycle @ TL= 110 °C, rectangular wave form
IFSM Max. Peak One Cycle Non-Repetitive 2000 A 5µs Sine or 3µs Rect. pulse
Surge Current 110 10ms Sine or 6ms Rect. pulse
EAS Non Repetitive Avalanche Energy 6.0 mJ TJ = 25 °C, IAS = 1.0A, L = 12mH
IAR Repetitive Avalanche Current 1.0 A Current decaying linearly to zero in 1 µsec
Frequency limited by TJ max. Va = 1.5 x Vr typical
Parameters 30BQ Units Conditions
Absolute Maximum Ratings
Following any rated
load condition and
with rated VRRM applied
TJ = 25 °C
Electrical Specifications
(1) Pulse Width < 300µs, Duty Cycle < 2%
VR = rated VR
TJ = 125 °C
Thermal-Mechanical Specifications
TJMax. Junction Temperature Range (*) - 55 to 150 °C
Tstg Max. Storage Temperature Range - 55 to 150 °C
RthJL Max. Thermal Resistance 12 °C/W DC operation
Junction to Lead (**)
RthJA Max. Thermal Resistance 46 °C/W DC operation
Junction to Ambient
wt Approximate Weight 0.24 (0.008) g (oz.)
Case Style SMC Similar to DO-214AB
Device Marking IR3F
Parameters 30BQ Units Conditions
(**) Mounted 1 inch square PCB
< thermal runaway condition for a diode on its own heatsink
(*) dPtot 1
dTj Rth( j-a)
30BQ040
Bulletin PD-2.439 rev. F 03/03
3
www.irf.com
Fig. 2 - Typical Values Of Reverse Current
Vs. Reverse Voltage (Per Leg)
Fig. 3 - Typical Junction Capacitance
Vs. Reverse Voltage (Per Leg)
Fig. 4 - Max. Thermal Impedance Z thJC Characteristics (Per Leg)
Fig. 1 - Max. Forward Voltage Drop
Characteristics (Per Leg)
Instantaneous Forward Current - I F (A)
Forward Voltage Drop - VFM (V)
Reverse Current - I R (µA)
Reverse Voltage - VR (V)
Reverse Voltage - VR (V)
Junction Capacitance - C T (p F)
Thermal Impedance Z thJC (°C/W)
t1 , Rectangular Pulse Duration (Seconds)
0.1
1
10
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
T = 150˚C
T = 125˚C
T = 25˚C
J
J
J
10
100
1000
0 5 10 15 20 25 30 35 40 45
T = 25˚C
J
0.1
1
10
100
0.00001 0.0001 0.001 0.01 0.1 1 10 100
Single Pulse
(Thermal Resistance)
D = 0.20
D = 0.25
D = 0.33
D = 0.50
D = 0.75
Notes:
1. Duty factor D = t1/ t 2
2. Peak Tj = Pdm x ZthJC+Tc
2
t
1
t
P
DM
1
10
100
1000
10000
100000
0 10203040
25˚C
50˚C
75˚C
100˚C
125˚C
T = 150˚C
J
30BQ040
Bulletin PD-2.439 rev. F 03/03
4www.irf.com
Fig. 4 - Maximum Average Forward Current
Vs. Allowable Lead Temperature Fig. 5 - Maximum Average Forward Dissipation
Vs. Average Forward Current
Fig. 6 - Maximum Peak Surge Forward Current Vs. Pulse Duration
(2) Formula used: TC = TJ - (Pd + PdREV) x RthJC ;
Pd = Forward Power Loss = IF(AV) x VFM @ (IF(AV) / D) (see Fig. 6);
PdREV = Inverse Power Loss = VR1 x IR (1 - D); IR @ VR1 = 80% rated VR
Average Forward Current - I F(AV) (A)
Allowable Lead Temperature (°C)
Average Forward Current - I F(AV) (A)
Average Power Loss (Watts)
Square Wave Pulse Duration - Tp
(Microsec)
Non-Repetitive Surge Current - I FSM (A)
10
100
1000
10000
10 100 1000 10000
At Any Rated Load Condition
And With Rated Vrrm Applied
Following Surge
70
80
90
100
110
120
130
140
150
160
012345
DC
D=0.20
D=0.25
D=0.33
D=0.50
D=0.75
Square wave (D = 0.50)
80% Rated Vr applied
see note (2)
0
0
.5
1
1
.5
2
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5
DC
RMS Limit
D = 0.75
D = 0.50
D = 0.33
D = 0.25
D = 0.20
30BQ040
Bulletin PD-2.439 rev. F 03/03
5
www.irf.com
Tape & Reel Information
Dimensions in millimetres and (inches)
Marking & Identification Ordering Information
30BQ SERIES - TAPE AND REEL
WHEN ORDERING, INDICATE THE PART
NUMBER AND THE QUANTITY ( IN MULTIPLES OF
3000 PIECES).
EXAMPLE: 30BQ040TR - 6000 PIECES
30BQ SERIES - BULK QUANTITIES
WHEN ORDERING, INDICATE THE PART NUMBER
AND THE QUANTITY ( IN MULTIPLES OF 1000
PIECES).
EXAMPLE: 30BQ040 - 2000 PIECES
16 (0.63)
FEED DIRECTION
8 (0.32)
16 (0.63)
330 (13)
IR LOGO
YEAR
CURRENT
IR3F VOLTAGE
YYWWX
WEEK
SITE ID
Each device has 2 rows for identification. The first row
designates the device as manufactured by International
Rectifier as indicated by the letters "IR", and the Part
Number (indicates the current and the voltage rating).
The second row indicates the year, the week of
manufacturing and the Site ID.
30BQ040
Bulletin PD-2.439 rev. F 03/03
6www.irf.com
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105
TAC Fax: (310) 252-7309
Visit us at www.irf.com for sales contact information. 03/03
Data and specifications subject to change without notice.
This product has been designed and qualified for Industrial Level.
Qualification Standards can be found on IR's Web site.