- 140 -
SF1004G-Q1
10.0 AMPS. Glass Passivated Super Fast Rectifiers
Voltage Range
200 Volts
Current
10.0 Amperes
Features
a Low forward voltage drop
a High current capability
a High reliability
a High surge current capability
Mechanical Data
a Case: Molded plastic
a Epoxy: UL 94V-O rate flame retardant
a Terminals: Leads solderable per MIL-STD-
Terminals: 202, Method 208 guaranteed
a Polarity: As marked
a High temperature soldering guaranteed:
250°C/10 seconds .16”,(4.06mm) from
case.
a Weight: 2.24 grams
TO-220
Dimensions in inches and (millimeters)
Maximum Ratings and Electrical Characteristics
Rating at 25°C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Type Number SF1004G-Q1 Units
Maximum Recurrent Peak Reverse Voltage 200 V
Maximum RMS Voltage 140 V
Maximum DC Blocking Voltage 200 V
Maximum Average Forward Rectified Current
.375 (9.5mm) Lead Length @TC = 100°C 10.0 A
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated Load
(JEDEC method ) 125 A
Maximum Instantaneous Forward Voltage
@ 5.0A
@10.0A 1.1
1.25
V
Maximum DC Reverse Current @ TA=25°C
at Rated DC Blocking Voltage @ TA=100°C 10.0
500 uA
uA
Reverse Recovery Charge(Per Diode) QS
@IF=2A, VR?30V,-dIF/dt=20A/uS 9NC
Thermal resistance Junction to Case RthJ-C
(Note 3) 3.0 °C/W
Rating for Fusing (t < 8.3mS) I2t65 A2S
Maximum Reverse Recovery Time (Note 1) 25 nS
Typical Junction Capacitance (Note 2) 10 pF
Operating Temperature Range TJ-50 to +150 °C
Storage Temperature Range TSTG -50 to +150 °C
Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A
Notes: 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C.
Notes: 3. Thermal Resistance from Junction to Case Mounted on Heatsink.
Preliminary
- 141 -
RATINGS AND CHARACTERISTIC CURVES (SF1004G-Q1)
FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50W
NONINDUCTIVE
1W
NON
INDUCTIVE
OSCILLOSCOPE
(NOTE 1)
PULSE
GENERATOR
(NOTE 2)
DUT
(+)
50Vdc
(approx)
(-)
NOTES: 1. Rise Time=7ns max. Input Impedance=
1 megohm 22pf
2. Rise Time=10ns max. Sourse Impedance=
50 ohms
(-)
(+)
10W
NONINDUCTIVE
-1.0A
-0.25A
0
+0.5A
trr
1cm SET TIME BASE FOR
5/ 10ns/ cm
FIG.2- MAXIMUM FORWARD CURRENT DERATING
CURVE
AVERAGE FORWARD CURRENT. (A)
050 100 150
0
2
4
6
8
10
CASE TEMPERATURE. ( C)
o
FIG.3- TYPICAL REVERSE CHARACTERISTICS
INSTANTANEOUS REVERSE CURRENT.( A)
020 40 60 80 100 120 140
1000
0.1
1.0
10
100
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
TC=25 C
0
TC=100 C
0
FIG.4- MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT
PEAK FORWARD SURGE CURRENT. (A)
12 5 10 20 10050
30
120
90
60
NUMBER OF CYCLES AT 60Hz
TC=125 C
0
8.3ms Single Half Sine Wave
JEDEC Method
FIG.5- TYPICAL JUNCTION CAPACITANCE
CAPACITANCE.(pF)
152 10 20 50 100 200 500
50
60
70
80
90
100
REVERSE VOLTAGE. (V)
Tj=25 C
0
FIG.6- TYPICAL FORWARD CHARACTERISTICS
INSTANTANEOUS FORWARD CURRENT. (A)
.4 .6 .8 1.0 1.2 1.4 1.6 1.8
.01
0.1
.03
1.0
0.3
10
3.0
30
100
FORWARD VOLTAGE. (V)
Tj=25 C
Pulse Width=300 s
1% Duty Cycle
o
