Product Folder Sample & Buy Technical Documents Support & Community Tools & Software LM2940-N, LM2940C SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 LM2940x 1-A Low Dropout Regulator 1 Features 3 Description * * * * * * * * The LM2940-N and LM2940C positive voltage regulators feature the ability to source 1 A of output current with a dropout voltage of typically 0.5 V and a maximum of 1 V over the entire temperature range. Furthermore, a quiescent current reduction circuit has been included which reduces the ground current when the differential between the input voltage and the output voltage exceeds approximately 3 V. The quiescent current with 1 A of output current and an input-output differential of 5 V is therefore only 30 mA. Higher quiescent currents only exist when the regulator is in the dropout mode (VIN - VOUT 3 V). 1 Input Voltage Range = 6 V to 26 V Dropout Voltage Typically 0.5 V at IOUT = 1 A Output Current in Excess of 1 A Output Voltage Trimmed Before Assembly Reverse Battery Protection Internal Short Circuit Current Limit Mirror Image Insertion Protection P+ Product Enhancement Tested 2 Applications * * * Post Regulator for Switching Supplies Logic Power Supplies Industrial Instrumentation space space space Designed also for vehicular applications, the LM2940N and LM2940C and all regulated circuitry are protected from reverse battery installations or 2battery jumps. During line transients, such as load dump when the input voltage can momentarily exceed the specified maximum operating voltage, the regulator will automatically shut down to protect both the internal circuits and the load. The LM2940-N and LM2940C cannot be harmed by temporary mirrorimage insertion. Familiar regulator features such as short circuit and thermal overload protection are also provided. Device Information(1) PART NUMBER LM2940-N LM2940C PACKAGE BODY SIZE (NOM) SOT-223 (4) 6.50 mm x 3.50 mm WSON (8) 4.00 mm x 4.00 mm TO-263 (3) 10.18 mm x 8.41 mm TO-220 (3) 14.986 mm x 10.16 mm TO-263 (3) 10.18 mm x 8.41 mm TO-220 (3) 14.986 mm x 10.16 mm (1) For all available packages, see the orderable addendum at the end of the datasheet. Simplified Schematic VIN Unregulated Input C1* 0.47 F IN LM2940 OUT VOUT Regulated Output + COUT** 22 F IQ *Required if regulator is located far from power supply filter. **COUT must be at least 22 F to maintain stability. May be increased without bound to maintain regulation during transients. Locate as close as possible to the regulator. This capacitor must be rated over the same operating temperature range as the regulator and the ESR is critical; see curve. 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LM2940-N, LM2940C SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 www.ti.com Table of Contents 1 2 3 4 5 6 7 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 4 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 4 4 4 5 5 6 7 8 Absolute Maximum Ratings ...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics (5 V and 8 V) .................... Electrical Characteristics (9 V and 10 V) .................. Electrical Characteristics (12 V and 15 V) ................ Typical Characteristics .............................................. Detailed Description ............................................ 13 7.1 Overview ................................................................. 13 7.2 Functional Block Diagram ....................................... 13 7.3 Feature Description................................................. 13 7.4 Device Functional Modes........................................ 14 8 Application and Implementation ........................ 15 8.1 Application Information............................................ 15 8.2 Typical Application .................................................. 15 9 Power Supply Recommendations...................... 17 10 Layout................................................................... 17 10.1 Layout Guidelines ................................................. 17 10.2 Layout Examples................................................... 17 10.3 Heatsinking ........................................................... 18 11 Device and Documentation Support ................. 20 11.1 11.2 11.3 11.4 11.5 Documentation Support ........................................ Related Links ........................................................ Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 20 20 20 20 20 12 Mechanical, Packaging, and Orderable Information ........................................................... 20 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision I (April 2013) to Revision J Page * Added Pin Configuration and Functions section, ESD Rating table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1 * Deleted information re: obsolete CDIP and CLGA package options ; Change pin names from Vin, Vout to IN, OUT; delete Heatsinking sections re: packages apart from TO-220 ............................................................................................... 1 * Changed symbols for Thermal Information ......................................................................................................................... 19 Changes from Revision H (April 2013) to Revision I 2 Submit Documentation Feedback Page Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LM2940-N LM2940C LM2940-N, LM2940C www.ti.com SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 5 Pin Configuration and Functions DDPAK/TO-263 (KTT) Package 3 Pins Top View DDPAK/TO-263 ( KTT) Package Side View WSON (NGN) Package 8 Pins Top View TO-220 (NDE) Package 4 Pins Front View N/C 1 GND 2 8 N/C 7 GND GND SOT-223 (DCY) Package 3 Pins Front View IN 3 6 OUT N/C 4 5 OUT Pin 2 and pin 7 are fused to center DAP Pin 5 and 6 need to be tied together on PCB board Pin Functions PIN NAME I/O DESCRIPTION NDE KTT DCY NGN IN 1 1 1 3 I GND 2 2 2 2 -- Ground OUT 3 3 3 5, 6 O Regulated output voltage. This pin requires an output capacitor to maintain stability. See Detailed Design Procedure for output capacitor details. Unregulated input voltage. GND 4 4 4 7 -- Ground N/C -- -- -- 1, 4, 8 -- No connection Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LM2940-N LM2940C Submit Documentation Feedback 3 LM2940-N, LM2940C SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 www.ti.com 6 Specifications 6.1 Absolute Maximum Ratings (1) (2) MIN MAX LM2940-N KTT, NDE, DCY 100 ms 60 LM2940C KTT, NDE 1 ms 45 Internal power dissipation (3) Internally Limited Maximum junction temperature Soldering temperature (4) 260 DDPAK/TO-263 (KTT) (30 s) 235 SOT-223 (DCY) (30 s) 260 WSON-8 (NGN) (30 s) (2) (3) (4) V 150 TO-220 (NDE), Wave (10 s) C 235 -65 Storage temperature, Tstg (1) UNIT 150 Absolute Maximum Ratings are limits beyond which damage to the device may occur. Recommended Operating Conditions are conditions under which the device functions but the specifications might not be ensured. For ensured specifications and test conditions see the Electrical Characteristics (5 V and 8 V). If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. The maximum allowable power dissipation is a function of the maximum junction temperature, TJ, the junction-to-ambient thermal resistance, RJA, and the ambient temperature, TA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. The value of R JA (for devices in still air with no heatsink) is 23.3C/W for the TO-220 package, 40.9C/W for the DDPAK/TO-263 package, and 59.3C/W for the SOT-223 package. The effective value of RJA can be reduced by using a heatsink (see Heatsinking for specific information on heatsinking). The value of RJA for the WSON package is specifically dependent on PCB trace area, trace material, and the number of layers and thermal vias. For improved thermal resistance and power dissipation for the WSON package, refer to Application Note AN-1187 Leadless Leadframe Package (LLP) (SNOA401). It is recommended that 6 vias be placed under the center pad to improve thermal performance. Refer to JEDEC J-STD-020C for surface mount device (SMD) package reflow profiles and conditions. Unless otherwise stated, the temperature and time are for Sn-Pb (STD) only. 6.2 ESD Ratings V(ESD) (1) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) VALUE UNIT 2000 V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. 6.3 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) MIN Input voltage LM2940-N NDE, LM2940-N KTT Temperature 4 LM2940C NDE, LM2940C KTT MAX UNIT V 6 26 -40 125 0 125 LM2940-N DCY -40 85 LM2940-N NGN -40 125 Submit Documentation Feedback C Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LM2940-N LM2940C LM2940-N, LM2940C www.ti.com SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 6.4 Thermal Information LM2940-N, LM2940C THERMAL METRIC (1) LM2940-N TO-220 (NDE) DDPAK/TO-263 (KTT) SOT-223 (DCY) WSON (NGN) 3 PINS 3 PINS 4 PINS 8 PINS (2) 23.3 40.9 59.3 40.5 RJC(top) Junction-to-case (top) thermal resistance 16.1 43.5 38.9 26.2 RJB Junction-to-board thermal resistance 4.8 23.5 8.1 17.0 JT Junction-to-top characterization parameter 2.7 10.3 1.7 0.2 JB Junction-to-board characterization parameter 4.8 22.5 8.0 17.2 RJC(bot) Junction-to-case (bottom) thermal resistance 1.1 0.8 n/a 3.2 RJA (1) (2) Junction-to-ambient thermal resistance UNIT C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. Thermal information for the TO-220 package is for a package vertically mounted with a heat sink in the middle of a PCB which is compliant to the JEDEC HIGH-K 2s2p (JESD51-7). The heatsink-to-ambient thermal resistance, RSA, is 21.7C/W. See Heatsinking TO-220 Package Parts for more information. 6.5 Electrical Characteristics (5 V and 8 V) Unless otherwise specified: VIN = VOUT + 5 V, IOUT = 1 A and COUT = 22 F. MIN (minimum) and MAX (maximum) limits apply over the recommended operating temperature range, unless otherwise noted; typical limits apply for TA = TJ = 25C. PARAMETER Input voltage Output voltage Line regulation Load regulation Output impedance 5V TEST CONDITIONS MIN 8V TYP MAX MIN TYP MAX 5 mA IOUT 1 A 6.25 26 9.4 5 mA IOUT 1A 4.75 5 5.25 7.6 8 8.4 5 mA IOUT 1A, TJ = 25C 4.85 7.76 8 8.24 26 5 5.15 VOUT + 2 V VIN 26 V, IOUT = 5 mA TJ = 25C 20 50 20 80 50 mA IOUT 1 A LM2940-N 35 80 55 130 50 mA IOUT 1 A TJ = 25C LM2940-N 35 50 55 80 LM2940C 35 50 55 80 100 mADC, 20 mArms, OUT = 120 Hz 35 VOUT + 2 V VIN 26 V, IOUT = 5 mA LM2940-N 10 20 10 20 VOUT + 2 V VIN 26 V, IOUT = 5 mA Quiescent current TJ = 25C LM2940-N 10 15 10 15 LM2940C 10 15 VIN = VOUT + 5 V, IOUT = 1 A 30 60 30 60 VIN = VOUT + 5 V, IOUT = 1 A TJ = 25C 30 45 30 45 Output noise voltage Ripple rejection 10 Hz to 100 kHz, IOUT = 5 mA Dropout voltage mV m 240 LM2940-N 54 72 48 66 OUT = 120 Hz, 1 Vrms, IOUT = 100 mA TJ = 25C LM2940-N 60 72 54 66 LM2940C 60 72 54 66 20 Vrms dB mV/1000 Hr 32 IOUT = 1A 0.5 1 0.5 1 IOUT = 1A, TJ = 25C 0.5 0.8 0.5 0.8 IOUT = 100 mA 110 200 110 200 IOUT = 100 mA, TJ = 25C 110 150 110 150 Product Folder Links: LM2940-N LM2940C mV mA 150 Copyright (c) 2000-2014, Texas Instruments Incorporated V 55 OUT = 120 Hz, 1 Vrms, IOUT = 100 mA Long-term stability UNIT Submit Documentation Feedback V mV 5 LM2940-N, LM2940C SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 www.ti.com Electrical Characteristics (5 V and 8 V) (continued) Unless otherwise specified: VIN = VOUT + 5 V, IOUT = 1 A and COUT = 22 F. MIN (minimum) and MAX (maximum) limits apply over the recommended operating temperature range, unless otherwise noted; typical limits apply for TA = TJ = 25C. PARAMETER Short-circuit current Maximum line transient Reverse polarity DC input voltage Reverse polarity Transient Input Voltage (1) 5V TEST CONDITIONS See (1), TJ = 25C 8V MIN TYP 1.6 MAX MIN TYP 1.9 1.6 1.9 ROUT = 100, T 100 ms LM2940-N 60 75 60 75 ROUT = 100, T 1 ms TJ = 25C LM2940C 45 55 45 555 ROUT = 100 LM2940-N -15 -30 -15 -30 ROUT = 100 TJ = 25C LM2940C -15 -30 -15 -30 ROUT = 100 , T 100 ms LM2940-N -50 -75 ROUT = 100 , T 1 ms LM2940C -45 -55 -50 MAX UNIT A V V -75 V Output current will decrease with increasing temperature but will not drop below 1 A at the maximum specified temperature. 6.6 Electrical Characteristics (9 V and 10 V) Unless otherwise specified: VIN = VOUT + 5 V, IOUT = 1 A and COUT = 22 F. MIN (minimum) and MAX (maximum) limits apply over the recommended operating temperature range, unless otherwise noted; typical limits apply for TA = TJ = 25C. PARAMETER Input voltage Output voltage Line regulation 9V TEST CONDITIONS MIN 10 V TYP MAX MIN TYP MAX 5 mA IOUT 1 A 10.5 26 11.5 5 mA IOUT 1A 8.55 9 9.45 9.5 10 10.5 5 mA IOUT 1A, TJ = 25C 8.73 9 9.27 9.7 10 10.3 VOUT + 2 V VIN 26 V, IOUT = 5 mA TJ = 25C 20 90 20 100 26 50 mA IOUT 1 A LM2940-N 60 150 65 165 Load regulation 50 mA IOUT 1 A TJ = 25C LM2940-N 60 90 65 100 LM2940C 60 90 Output impedance 100 mADC, 20 mArms, OUT = 120 Hz 60 VOUT + 2 V VIN 26 V, IOUT = 5 mA LM2940-N 10 20 VOUT + 2 V VIN 26 V, IOUT = 5 mA Quiescent current TJ = 25C LM2940-N 10 15 LM2940C 10 15 VIN = VOUT + 5 V, IOUT = 1 A 30 60 30 60 VIN = VOUT + 5 V, IOUT = 1 A TJ = 25C 30 45 30 45 Output noise voltage 10 Hz to 100 kHz, IOUT = 5 mA OUT = 120 Hz, 1 Vrms IOUT = 100 mA Ripple rejection OUT = 120 Hz, 1 Vrms IOUT = 100 mA TJ = 25C Long-term stability Dropout voltage 6 65 10 V mV mV m 20 15 mA 270 300 Vrms LM2940-N 46 64 45 63 LM2940-N 52 64 51 63 dB LM2940C 52 64 36 mV/1000 Hr 34 IOUT = 1A 0.5 1 0.5 1 IOUT = 1A, TJ = 25C 0.5 0.8 0.5 0.8 IOUT = 100 mA 110 200 110 200 IOUT = 100 mA, TJ = 25C 110 150 110 150 Submit Documentation Feedback UNIT V mV Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LM2940-N LM2940C LM2940-N, LM2940C www.ti.com SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 Electrical Characteristics (9 V and 10 V) (continued) Unless otherwise specified: VIN = VOUT + 5 V, IOUT = 1 A and COUT = 22 F. MIN (minimum) and MAX (maximum) limits apply over the recommended operating temperature range, unless otherwise noted; typical limits apply for TA = TJ = 25C. PARAMETER Short-circuit current Maximum line transient Reverse polarity DC input voltage Reverse polarity Transient Input Voltage (1) 9V TEST CONDITIONS See (1), TJ = 25C MIN TYP 1.6 MIN TYP 1.9 1.6 1.9 60 75 ROUT = 100, T 100 ms LM2940-N 60 75 ROUT = 100, T 100 ms TJ = 25C LM2940C 45 55 ROUT = 100 LM2940-N -15 -30 -15 -30 LM2940-N -50 -75 LM2940C -45 -55 ROUT = 100 TJ = 25C LM2940C ROUT = 100 , T 100 ms 10 V MAX MAX UNIT A V -15 -30 V -50 -75 V Output current will decrease with increasing temperature but will not drop below 1 A at the maximum specified temperature. 6.7 Electrical Characteristics (12 V and 15 V) Unless otherwise specified: VIN = VOUT + 5 V, IOUT = 1 A and COUT = 22 F. MIN (minimum) and MAX (maximum) limits apply over the recommended operating temperature range, unless otherwise noted; typical limits apply for TA = TJ = 25C. PARAMETER Input voltage Output voltage Line regulation 12 V TEST CONDITIONS MIN 15 V TYP MAX MIN TYP MAX 5 mA IOUT 1 A 13.6 26 16.75 5 mA IOUT 1A 11.40 12 12.6 14.25 15 15.75 5 mA IOUT 1A, TJ = 25C 11.64 12 12.36 14.55 15 15.45 VOUT + 2 V VIN 26 V, IOUT = 5 mA TJ = 25C 20 120 20 150 26 50 mA IOUT 1 A LM2940-N 55 200 Load regulation 50 mA IOUT 1 A TJ = 25C LM2940-N 55 120 LM2940C 55 120 Output impedance 100 mADC, 20 mArms, OUT = 120 Hz 80 VOUT + 2 V VIN 26 V, IOUT = 5 mA LM2940-N 10 20 VOUT + 2 V VIN 26 V, IOUT = 5 mA Quiescent current TJ = 25C LM2940-N 10 15 LM2940C 10 15 10 15 VIN = VOUT + 5 V, IOUT = 1 A 30 60 30 60 VIN = VOUT + 5 V, IOUT = 1 A TJ = 25C 30 45 30 45 Output noise voltage Ripple rejection 10 Hz to 100 kHz, IOUT = 5 mA LM2940-N 48 66 OUT = 120 Hz, 1 Vrms, IOUT = 100 mA TJ = 25C LM2940-N 54 66 LM2940C 54 66 Long-term stability Dropout voltage 70 150 m 450 mA Vrms dB 52 64 mV/1000 Hr 60 IOUT = 1A 0.5 1 0.5 1 IOUT = 1A, TJ = 25C 0.5 0.8 0.5 0.8 IOUT = 100 mA 110 200 110 200 IOUT = 100 mA, TJ = 25C 110 150 110 150 Product Folder Links: LM2940-N LM2940C mV 100 48 Copyright (c) 2000-2014, Texas Instruments Incorporated V mV 360 OUT = 120 Hz, 1 Vrms, IOUT = 100 mA UNIT Submit Documentation Feedback V mV 7 LM2940-N, LM2940C SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 www.ti.com Electrical Characteristics (12 V and 15 V) (continued) Unless otherwise specified: VIN = VOUT + 5 V, IOUT = 1 A and COUT = 22 F. MIN (minimum) and MAX (maximum) limits apply over the recommended operating temperature range, unless otherwise noted; typical limits apply for TA = TJ = 25C. PARAMETER Short-circuit current See (1), TJ = 25C Maximum line transient Reverse polarity DC input voltage Reverse polarity transient input voltage (1) 12 V TEST CONDITIONS 15 V MIN TYP 1.6 1.9 ROUT = 100, T 100 ms LM2940-N 60 75 ROUT = 100, T 100 ms TJ = 25C LM2940C 45 55 ROUT = 100 LM2940-N -15 -30 ROUT = 100 TJ = 25C LM2940C -15 -30 ROUT = 100 , T 100 ms LM2940-N -50 -75 LM2940C -45 -55 ROUT = 100 , T 1 ms MAX MIN TYP 1.6 1.9 45 55 -15 -30 -45 -55 MAX UNIT A V V V Output current will decrease with increasing temperature but will not drop below 1 A at the maximum specified temperature. 6.8 Typical Characteristics 8 Figure 1. Dropout Voltage Figure 2. Dropout Voltage vs. Temperature Figure 3. Output Voltage vs. Temperature Figure 4. Quiescent Current vs. Temperature Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LM2940-N LM2940C LM2940-N, LM2940C www.ti.com SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 Typical Characteristics (continued) Figure 5. Quiescent Current Figure 6. Quiescent Current Figure 7. Line Transient Response Figure 8. Load Transient Response Figure 9. Ripple Rejection Figure 10. Low Voltage Behavior Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LM2940-N LM2940C Submit Documentation Feedback 9 LM2940-N, LM2940C SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 www.ti.com Typical Characteristics (continued) 10 Figure 11. Low Voltage Behavior Figure 12. Low Voltage Behavior Figure 13. Low Voltage Behavior Figure 14. Low Voltage Behavior Figure 15. Output at Voltage Extremes Figure 16. Output at Voltage Extremes Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LM2940-N LM2940C LM2940-N, LM2940C www.ti.com SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 Typical Characteristics (continued) Figure 17. Output at Voltage Extremes Figure 18. Output at Voltage Extremes Figure 19. Output at Voltage Extremes Figure 20. Output Capacitor ESR Figure 21. Peak Output Current Figure 22. Output Impedance Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LM2940-N LM2940C Submit Documentation Feedback 11 LM2940-N, LM2940C SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 www.ti.com Typical Characteristics (continued) Figure 23. Maximum Power Dissipation (TO-220) Figure 24. Maximum Power Dissipation (SOT-223) Figure 25. Maximum Power Dissipation (DDPAK/TO-263) 12 Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LM2940-N LM2940C LM2940-N, LM2940C www.ti.com SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 7 Detailed Description 7.1 Overview The LM2940 positive voltage regulator features the ability to source 1 A of output current with a dropout voltage of typically 0.5 V and a maximum of 1 V over the entire temperature range. Furthermore, a quiescent current reduction circuit has been included which reduces the ground current when the differential between the input voltage and the output voltage exceeds approximately 3 V. The quiescent current with 1 A of output current and an input-output differential of 5 V is therefore only 30 mA. Higher quiescent currents only exist when the regulator is in the dropout mode (VIN - VOUT 3 V). 7.2 Functional Block Diagram IN OUT PNP OVSD (30 V) Current Limit Thermal Shutdown + Bandgap Reference GND 7.3 Feature Description 7.3.1 Short-Circuit Current Limit The internal current limit circuit is used to protect the LDO against high-load current faults or shorting events. The LDO is not designed to operate in a steady-state current limit. During a current-limit event, the LDO sources constant current. Therefore, the output voltage falls when load impedance decreases. Note, also, that if a current limit occurs and the resulting output voltage is low, excessive power may be dissipated across the LDO, resulting a thermal shutdown of the output. 7.3.2 Overvoltage Shutdown (OVSD) Input voltage greater than typically 30 V will cause the LM2940 output to be disabled. When operating with the input voltage greater than the maximum recommended input voltage of 26 V, the device performance is not ensured. Continuous operation with the input voltage greater than the maximum recommended input voltage is discouraged. 7.3.3 Thermal Shutdown (TSD) The LM2940 contains the thermal shutdown circuitry to turn off the output when excessive heat is dissipated in the LDO. The internal protection circuitry of the LM2940 is designed to protect against thermal overload conditions. The TSD circuitry is not intended to replace proper heat sinking. Continuously running the device into thermal shutdown degrades its reliability as the junction temperature will be exceeding the absolute maximum junction temperature rating. Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LM2940-N LM2940C Submit Documentation Feedback 13 LM2940-N, LM2940C SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 www.ti.com 7.4 Device Functional Modes 7.4.1 Operation with Enable Control The LM2940 design does not include any undervoltage lockout (UVLO), or enable functions. Generally, the output voltage will track the input voltage until the input voltage is greater than VOUT + 1V. When the input voltage is greater than VOUT + 1 V, the LM2940 will be in linear operation, and the output voltage will be regulated. However, the device will be sensitive to any small perturbation of the input voltage. Device dynamic performance is improved when the input voltage is at least 2 V greater than the output voltage. 14 Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LM2940-N LM2940C LM2940-N, LM2940C www.ti.com SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 8.1 Application Information The LM2940-N and LM2940C positive voltage regulators feature the ability to source 1 A of output current with a dropout voltage of typically 0.5 V and a maximum of 1 V over the entire temperature range. The output capacitor, COUT, must have a capacitance value of at least 22 F with an ESR of at least 100 m, but no more than 1 . The minimum capacitance value and the ESR requirements apply across the entire expected operating ambient temperature range. 8.2 Typical Application VIN Unregulated Input LM2940 IN VOUT Regulated Output OUT + COUT** C1* 0.47 F 22 F IQ *Required if regulator is located far from power supply filter. **COUT must be at least 22 F to maintain stability. May be increased without bound to maintain regulation during transients. Locate as close as possible to the regulator. This capacitor must be rated over the same operating temperature range as the regulator and the ESR is critical; see curve. Figure 26. Typical Application 8.2.1 Design Requirements Table 1. Design Parameters DESIGN PARAMETER EXAMPLE VALUE Input voltage range 6 V to 26 V Output voltage range 8V Output current range 5 mA to 1 A Input capacitor value 0.47 F Output capacitor value 22 F minimum Output capacitor ESR range 100 m to 1 8.2.2 Detailed Design Procedure 8.2.2.1 External Capacitors The output capacitor is critical to maintaining regulator stability, and must meet the required conditions for both equivalent series resistance (ESR) and minimum amount of capacitance. 8.2.2.1.1 Minimum Capacitance The minimum output capacitance required to maintain stability is 22 F (this value may be increased without limit). Larger values of output capacitance will give improved transient response. Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LM2940-N LM2940C Submit Documentation Feedback 15 LM2940-N, LM2940C SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 www.ti.com 8.2.2.1.2 ESR Limits The ESR of the output capacitor will cause loop instability if it is too high or too low. The acceptable range of ESR plotted versus load current is shown in the graph below. It is essential that the output capacitor meet these requirements, or oscillations can result. Figure 27. Output Capacitor ESR Limits It is important to note that for most capacitors, ESR is specified only at room temperature. However, the designer must ensure that the ESR will stay inside the limits shown over the entire operating temperature range for the design. For aluminum electrolytic capacitors, ESR will increase by about 30X as the temperature is reduced from 25C to -40C. This type of capacitor is not well-suited for low temperature operation. Solid tantalum capacitors have a more stable ESR over temperature, but are more expensive than aluminum electrolytics. A cost-effective approach sometimes used is to parallel an aluminum electrolytic with a solid tantalum, with the total capacitance split about 75/25% with the aluminum being the larger value. If two capacitors are paralleled, the effective ESR is the parallel of the two individual values. The flatter ESR of the tantalum will keep the effective ESR from rising as quickly at low temperatures. 8.2.3 Application Curves Figure 28. Low Voltage Behavior 16 Submit Documentation Feedback Figure 29. Output at Voltage Extremes Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LM2940-N LM2940C LM2940-N, LM2940C www.ti.com SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 9 Power Supply Recommendations The device is designed to operate from an input voltage supply range between VOUT + 1 V up to a maximum of 26 V. This input supply must be well regulated and free of spurious noise. To ensure that the LM2940 output voltage is well regulated, the input supply should be at least VOUT + 2 V. 10 Layout 10.1 Layout Guidelines The dynamic performance of the LM2940 is dependent on the layout of the PCB. PCB layout practices that are adequate for typical LDOs may degrade the PSRR, noise, or transient performance of the LM2940. Best performance is achieved by placing CIN and COUT on the same side of the PCB as the LM2940, and as close as is practical to the package. The ground connections for CIN and COUT should be back to the LM2940 ground pin using as wide and short of a copper trace as is practical. 10.2 Layout Examples Ground 5 1 6 2 CIN COUT GND VIN 3 7 4 8 VOUT Figure 30. LM2940 WSON Layout 4 3 2 COUT 1 CIN VIN VOUT Ground Figure 31. LM2940 SOT-223 Layout 4 CIN VIN COUT 1 2 3 VOUT Ground Figure 32. TO-263 Layout Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LM2940-N LM2940C Submit Documentation Feedback 17 LM2940-N, LM2940C SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 www.ti.com 10.3 Heatsinking A heatsink may be required depending on the maximum power dissipation and maximum ambient temperature of the application. Under all possible operating conditions, the junction temperature must be within the range specified under Absolute Maximum Ratings (1) (2). To determine if a heatsink is required, the power dissipated by the regulator, PD, must be calculated. Figure 33 shows the voltages and currents which are present in the circuit, as well as the formula for calculating the power dissipated in the regulator: IIN = IL + IG PD = (VIN - VOUT) IL + (VIN) IG Figure 33. Power Dissipation Diagram The next parameter which must be calculated is the maximum allowable temperature rise, TR(MAX). This is calculated by using the formula: TR(MAX) = TJ(MAX) - TA(MAX) where * * TJ(MAX) is the maximum allowable junction temperature, which is 125C for commercial grade parts. TA(MAX)is the maximum ambient temperature which will be encountered in the application. (1) Using the calculated values for TR(MAX) and PD, the maximum allowable value for the junction-to-ambient thermal resistance, RJA, can now be found: RJA = TR(MAX) / PD (2) NOTE If the maximum allowable value for RJA is found to be 23.3C/W for the TO-220 package (with a heatsink of 21.7C/W RSA), 40.9C/W for the DDPAK/TO-263 package, or 59.3C/W for the SOT-223 package, no heatsink is needed since the package alone will dissipate enough heat to satisfy these requirements. If the calculated value for RJA falls below these limits, a heatsink is required. (1) (2) 18 Absolute Maximum Ratings are limits beyond which damage to the device may occur. Recommended Operating Conditions are conditions under which the device functions but the specifications might not be ensured. For ensured specifications and test conditions see the Electrical Characteristics (5 V and 8 V). If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LM2940-N LM2940C LM2940-N, LM2940C www.ti.com SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 Heatsinking (continued) 10.3.1 Heatsinking TO-220 Package Parts The TO-220 can be attached to a typical heatsink, or secured to a copper plane on a PC board. If a manufactured heatsink is to be selected, the value of heatsink-to-ambient thermal resistance, RSA, must first be calculated: RSA = RJA - RCS - RJC where * * RJC is defined as the thermal resistance from the junction to the surface of the case. A value of 3C/W can be assumed for RJC for this calculation. RCS is defined as the thermal resistance between the case and the surface of the heatsink. The value of RCS will vary from about 0.5C/W to about 2.5C/W (depending on method of attachment, insulator, etc.). If the exact value is unknown, 2C/W should be assumed for RCS. (3) When a value for RSA is found using Equation 3, a heatsink must be selected that has a value that is less than or equal to this number. RSA is specified numerically by the heatsink manufacturer in the catalog, or shown in a curve that plots temperature rise vs power dissipation for the heatsink. Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LM2940-N LM2940C Submit Documentation Feedback 19 LM2940-N, LM2940C SNVS769J - MARCH 2000 - REVISED DECEMBER 2014 www.ti.com 11 Device and Documentation Support 11.1 Documentation Support 11.1.1 Related Documentation For related documentation see the following: * Application Note AN-1028 Maximum Power Enhancement Techniques for Power Packages (SNVA036). * Application Note AN-1187 Leadless Leadframe Package (LLP) (SNOA401). 11.2 Related Links The table below lists quick access links. Categories include technical documents, support and community resources, tools and software, and quick access to sample or buy. Table 2. Related Links PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL DOCUMENTS TOOLS & SOFTWARE SUPPORT & COMMUNITY LM2940-N Click here Click here Click here Click here Click here LM2940C Click here Click here Click here Click here Click here 11.3 Trademarks All trademarks are the property of their respective owners. 11.4 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 11.5 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 12 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. 20 Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LM2940-N LM2940C PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2017 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM2940C-12 MWC ACTIVE WAFERSALE YS 0 1 Green (RoHS & no Sb/Br) Call TI Level-1-NA-UNLIM -40 to 85 LM2940CS-12 NRND DDPAK/ TO-263 KTT 3 45 TBD Call TI Call TI 0 to 125 LM2940CS -12 P+ LM2940CS-12/NOPB ACTIVE DDPAK/ TO-263 KTT 3 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM2940CS -12 P+ LM2940CS-15 NRND DDPAK/ TO-263 KTT 3 45 TBD Call TI Call TI 0 to 125 LM2940CS -15 P+ LM2940CS-15/NOPB ACTIVE DDPAK/ TO-263 KTT 3 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM2940CS -15 P+ LM2940CS-5.0 NRND DDPAK/ TO-263 KTT 3 45 TBD Call TI Call TI 0 to 125 LM2940CS -5.0 P+ LM2940CS-5.0/NOPB ACTIVE DDPAK/ TO-263 KTT 3 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM2940CS -5.0 P+ LM2940CS-9.0/NOPB ACTIVE DDPAK/ TO-263 KTT 3 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM2940CS -9.0 P+ LM2940CSX-12 NRND DDPAK/ TO-263 KTT 3 500 TBD Call TI Call TI 0 to 125 LM2940CS -12 P+ LM2940CSX-12/NOPB ACTIVE DDPAK/ TO-263 KTT 3 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM2940CS -12 P+ LM2940CSX-15/NOPB ACTIVE DDPAK/ TO-263 KTT 3 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM2940CS -15 P+ LM2940CSX-5.0 NRND DDPAK/ TO-263 KTT 3 500 TBD Call TI Call TI 0 to 125 LM2940CS -5.0 P+ LM2940CSX-5.0/NOPB ACTIVE DDPAK/ TO-263 KTT 3 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM2940CS -5.0 P+ LM2940CSX-9.0/NOPB ACTIVE DDPAK/ TO-263 KTT 3 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM2940CS -9.0 P+ LM2940CT-12 NRND TO-220 NDE 3 45 TBD Call TI Call TI 0 to 125 LM2940CT -12 P+ LM2940CT-12/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM 0 to 125 LM2940CT -12 P+ LM2940CT-15 NRND TO-220 NDE 3 45 TBD Call TI Call TI 0 to 125 LM2940CT -15 P+ Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 14-Oct-2017 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM2940CT-15/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM 0 to 125 LM2940CT -15 P+ LM2940CT-5.0 NRND TO-220 NDE 3 45 TBD Call TI Call TI 0 to 125 LM2940CT -5.0 P+ LM2940CT-5.0/LF01 ACTIVE TO-220 NDG 3 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR LM2940CT-5.0/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM 0 to 125 LM2940CT -5.0 P+ LM2940CT-9.0/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM 0 to 125 LM2940CT -9.0 P+ LM2940IMP-10/NOPB ACTIVE SOT-223 DCY 4 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 L55B LM2940IMP-12/NOPB ACTIVE SOT-223 DCY 4 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 L56B LM2940IMP-15 NRND SOT-223 DCY 4 1000 TBD Call TI Call TI -40 to 85 L70B LM2940IMP-15/NOPB ACTIVE SOT-223 DCY 4 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 L70B LM2940CT -5.0 P+ LM2940IMP-5.0 NRND SOT-223 DCY 4 1000 TBD Call TI Call TI -40 to 85 L53B LM2940IMP-5.0/NOPB ACTIVE SOT-223 DCY 4 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 L53B LM2940IMP-9.0/NOPB ACTIVE SOT-223 DCY 4 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 L0EB LM2940IMPX-10/NOPB ACTIVE SOT-223 DCY 4 2000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 L55B LM2940IMPX-12/NOPB ACTIVE SOT-223 DCY 4 2000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 L56B LM2940IMPX-5.0/NOPB ACTIVE SOT-223 DCY 4 2000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 L53B LM2940IMPX-8.0/NOPB ACTIVE SOT-223 DCY 4 2000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 L54B LM2940LD-12 NRND WSON NGN 8 1000 TBD Call TI Call TI -40 to 125 L00018B LM2940LD-12/NOPB ACTIVE WSON NGN 8 1000 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 L00018B LM2940LD-5.0/NOPB ACTIVE WSON NGN 8 1000 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 L00014B Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2017 Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM2940S-10 NRND DDPAK/ TO-263 KTT 3 45 TBD Call TI Call TI -40 to 125 LM2940S -10 P+ LM2940S-10/NOPB ACTIVE DDPAK/ TO-263 KTT 3 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM2940S -10 P+ LM2940S-12 NRND DDPAK/ TO-263 KTT 3 45 TBD Call TI Call TI -40 to 125 LM2940S -12 P+ LM2940S-12/NOPB ACTIVE DDPAK/ TO-263 KTT 3 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM2940S -12 P+ LM2940S-5.0 NRND DDPAK/ TO-263 KTT 3 45 TBD Call TI Call TI -40 to 125 LM2940S -5.0 P+ LM2940S-5.0/NOPB ACTIVE DDPAK/ TO-263 KTT 3 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM2940S -5.0 P+ LM2940S-8.0/NOPB ACTIVE DDPAK/ TO-263 KTT 3 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM2940S -8.0 P+ LM2940S-9.0/NOPB ACTIVE DDPAK/ TO-263 KTT 3 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM2940S -9.0 P+ LM2940SX-10 NRND DDPAK/ TO-263 KTT 3 500 TBD Call TI Call TI -40 to 125 LM2940S -10 P+ LM2940SX-10/NOPB ACTIVE DDPAK/ TO-263 KTT 3 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM2940S -10 P+ LM2940SX-12 NRND DDPAK/ TO-263 KTT 3 500 TBD Call TI Call TI -40 to 125 LM2940S -12 P+ LM2940SX-12/NOPB ACTIVE DDPAK/ TO-263 KTT 3 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM2940S -12 P+ LM2940SX-5.0 NRND DDPAK/ TO-263 KTT 3 500 TBD Call TI Call TI -40 to 125 LM2940S -5.0 P+ LM2940SX-5.0/NOPB ACTIVE DDPAK/ TO-263 KTT 3 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM2940S -5.0 P+ LM2940SX-8.0/NOPB ACTIVE DDPAK/ TO-263 KTT 3 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM2940S -8.0 P+ LM2940SX-9.0/NOPB ACTIVE DDPAK/ TO-263 KTT 3 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM2940S -9.0 P+ LM2940T-10.0 NRND TO-220 NDE 3 45 TBD Call TI Call TI -40 to 125 LM2940T 10.0 P+ LM2940T-10.0/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 125 LM2940T 10.0 P+ Addendum-Page 3 Samples PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2017 Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM2940T-12.0 NRND TO-220 NDE 3 45 TBD Call TI Call TI -40 to 125 LM2940T 12.0 P+ LM2940T-12.0/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 125 LM2940T 12.0 P+ LM2940T-5.0 NRND TO-220 NDE 3 45 TBD Call TI Call TI -40 to 125 LM2940T -5.0 P+ LM2940T-5.0/LF08 ACTIVE TO-220 NEB 3 45 Green (RoHS & no Sb/Br) CU SN Level-3-245C-168 HR LM2940T-5.0/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 125 LM2940T -5.0 P+ LM2940T-8.0 NRND TO-220 NDE 3 45 TBD Call TI Call TI -40 to 125 LM2940T -8.0 P+ LM2940T-8.0/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 125 LM2940T -8.0 P+ LM2940T-9.0 NRND TO-220 NDE 3 45 TBD Call TI Call TI -40 to 125 LM2940T -9.0 P+ LM2940T-9.0/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 125 LM2940T -9.0 P+ LM2940T -5.0 P+ (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. Addendum-Page 4 Samples PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2017 (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 5 PACKAGE MATERIALS INFORMATION www.ti.com 24-Aug-2017 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM2940CSX-12 DDPAK/ TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LM2940CSX-12/NOPB DDPAK/ TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LM2940CSX-15/NOPB DDPAK/ TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LM2940CSX-5.0 DDPAK/ TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LM2940CSX-5.0/NOPB DDPAK/ TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LM2940CSX-9.0/NOPB DDPAK/ TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LM2940IMP-10/NOPB LM2940IMP-12/NOPB SOT-223 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 SOT-223 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LM2940IMP-15 SOT-223 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LM2940IMP-15/NOPB SOT-223 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LM2940IMP-5.0 SOT-223 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LM2940IMP-5.0/NOPB SOT-223 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LM2940IMP-9.0/NOPB SOT-223 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LM2940IMPX-10/NOPB SOT-223 DCY 4 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 24-Aug-2017 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM2940IMPX-12/NOPB SOT-223 DCY 4 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LM2940IMPX-5.0/NOPB SOT-223 DCY 4 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LM2940IMPX-8.0/NOPB SOT-223 DCY 4 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LM2940LD-12 WSON NGN 8 1000 178.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1 LM2940LD-12/NOPB WSON NGN 8 1000 178.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1 LM2940LD-5.0/NOPB WSON NGN 8 1000 178.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1 LM2940SX-10 DDPAK/ TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LM2940SX-10/NOPB DDPAK/ TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LM2940SX-12 DDPAK/ TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LM2940SX-12/NOPB DDPAK/ TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LM2940SX-5.0 DDPAK/ TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LM2940SX-5.0/NOPB DDPAK/ TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LM2940SX-8.0/NOPB DDPAK/ TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LM2940SX-9.0/NOPB DDPAK/ TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 24-Aug-2017 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM2940CSX-12 DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0 LM2940CSX-12/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0 LM2940CSX-15/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0 LM2940CSX-5.0 DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0 LM2940CSX-5.0/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0 LM2940CSX-9.0/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0 LM2940IMP-10/NOPB SOT-223 DCY 4 1000 367.0 367.0 35.0 LM2940IMP-12/NOPB SOT-223 DCY 4 1000 367.0 367.0 35.0 LM2940IMP-15 SOT-223 DCY 4 1000 367.0 367.0 35.0 LM2940IMP-15/NOPB SOT-223 DCY 4 1000 367.0 367.0 35.0 LM2940IMP-5.0 SOT-223 DCY 4 1000 367.0 367.0 35.0 LM2940IMP-5.0/NOPB SOT-223 DCY 4 1000 367.0 367.0 35.0 LM2940IMP-9.0/NOPB SOT-223 DCY 4 1000 367.0 367.0 35.0 LM2940IMPX-10/NOPB SOT-223 DCY 4 2000 367.0 367.0 35.0 LM2940IMPX-12/NOPB SOT-223 DCY 4 2000 367.0 367.0 35.0 LM2940IMPX-5.0/NOPB SOT-223 DCY 4 2000 367.0 367.0 35.0 LM2940IMPX-8.0/NOPB SOT-223 DCY 4 2000 367.0 367.0 35.0 LM2940LD-12 WSON NGN 8 1000 210.0 185.0 35.0 LM2940LD-12/NOPB WSON NGN 8 1000 210.0 185.0 35.0 LM2940LD-5.0/NOPB WSON NGN 8 1000 210.0 185.0 35.0 LM2940SX-10 DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0 LM2940SX-10/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0 LM2940SX-12 DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0 LM2940SX-12/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0 LM2940SX-5.0 DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0 LM2940SX-5.0/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0 LM2940SX-8.0/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0 LM2940SX-9.0/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0 Pack Materials-Page 3 MECHANICAL DATA NDE0003B www.ti.com MECHANICAL DATA KTT0003B TS3B (Rev F) BOTTOM SIDE OF PACKAGE www.ti.com MECHANICAL DATA NDG0003F T03F (Rev B) www.ti.com MECHANICAL DATA NGN0008A LDC08A (Rev B) www.ti.com MECHANICAL DATA MPDS094A - APRIL 2001 - REVISED JUNE 2002 DCY (R-PDSO-G4) PLASTIC SMALL-OUTLINE 6,70 (0.264) 6,30 (0.248) 3,10 (0.122) 2,90 (0.114) 4 0,10 (0.004) M 3,70 (0.146) 3,30 (0.130) 7,30 (0.287) 6,70 (0.264) Gauge Plane 1 2 0,84 (0.033) 0,66 (0.026) 2,30 (0.091) 4,60 (0.181) 1,80 (0.071) MAX 3 0-10 0,10 (0.004) M 0,25 (0.010) 0,75 (0.030) MIN 1,70 (0.067) 1,50 (0.059) 0,35 (0.014) 0,23 (0.009) Seating Plane 0,08 (0.003) 0,10 (0.0040) 0,02 (0.0008) 4202506/B 06/2002 NOTES: A. B. C. D. All linear dimensions are in millimeters (inches). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion. Falls within JEDEC TO-261 Variation AA. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2017, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM2940CS-12 LM2940CS-12/NOPB LM2940CS-15 LM2940CS-15/NOPB LM2940CS-5.0 LM2940CS-5.0/NOPB LM2940CS-9.0 LM2940CS-9.0/NOPB LM2940CSX-12 LM2940CSX-12/NOPB LM2940CSX-15 LM2940CSX15/NOPB LM2940CSX-5.0 LM2940CSX-5.0/NOPB LM2940CSX-9.0 LM2940CSX-9.0/NOPB LM2940CT-12 LM2940CT-12/NOPB LM2940CT-15 LM2940CT-15/NOPB LM2940CT-5.0 LM2940CT-5.0/LF01 LM2940CT5.0/NOPB LM2940CT-9.0 LM2940CT-9.0/NOPB LM2940C-12 MWC