L78LxxAB, L78LxxAC, L78LxxC Positive voltage regulators Datasheet -- production data Features Output current up to 100 mA Output voltages of 3.3; 5; 6; 8; 9; 10; 12; 15; 18; 24 V Thermal overload protection Short-circuit protection No external components are required Available in either 4% (AC) or 8% (C) selection TO-92 Description SO-8 The L78Lxx series of three-terminal positive regulators employ internal current limiting and thermal shutdown, making them essentially indestructible. If adequate heat-sink is provided, they can deliver up to 100 mA output current. They are intended as fixed voltage regulators in a wide range of applications including local or oncard regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, they can be used with power pass elements to make high-current voltage regulators. The L78Lxx series used as Zener diode/resistor combination replacement, offers an effective output impedance improvement Table 1. SOT-89 of typically two orders of magnitude, along with lower quiescent current and lower noise. Device summary Part numbers L78L33C L78L08AC L78L15C L78L33AC L78L08AB L78L15AC L78L33AB L78L09C L78L15AB L78L05C L78L09AC L78L18C L78L05AC L78L09AB L78L18AC L78L05AB L78L10AC L78L24C L78L06AC L78L12C L78L24AC L78L06AB L78L12AC L78L24AB L78L08C L78L12AB August 2012 This is information on a product in full production. Doc ID 2145 Rev 20 1/30 www.st.com 30 Contents L78LxxAB, L78LxxAC, L78LxxC Contents 1 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Typical performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 8 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 2/30 Doc ID 2145 Rev 20 L78LxxAB, L78LxxAC, L78LxxC 1 Diagram Figure 1. Schematic diagram Diagram Doc ID 2145 Rev 20 3/30 Pin configuration L78LxxAB, L78LxxAC, L78LxxC 2 Pin configuration Figure 2. Pin connection (top view, bottom view for TO-92) PIN 1 = VOUT PIN 2 = GND PIN 3 = VIN SO-8 Figure 3. 4/30 SOT-89 Test circuits Doc ID 2145 Rev 20 TO-92 L78LxxAB, L78LxxAC, L78LxxC Maximum ratings 3 Maximum ratings Table 2. Absolute maximum ratings Symbol VI IO PD Parameter DC Input voltage Value VO= 3.3 to 9 V 30 VO= 12 to 15 V 35 VO= 18 to 24 V 40 Output current Unit V 100 Power dissipation mA Internally limited TSTG Storage temperature range TOP Operating junction temperature range (1) -65 to 150 for L78L00AC 0 to 125 for L78L00AB -40 to 125 mW C C 1. Our SO-8 package used for voltage regulators is modified internally to have pins 2, 3, 6 and 7 electrically communed to the die attach flag. This particular frame decreases the total thermal resistance of the package and increases its ability to dissipate power when an appropriate area of copper on the printed circuit board is available for heat-sinking. The external dimensions are the same as for the standard SO-8. Table 3. Symbol RthJC RthJA 1. Thermal data Parameter SO-8 Thermal resistance junction-case. (max) Thermal resistance junction-ambient. (max) TO-92 20 55 (1) 200 SOT-89 Unit 15 C/W 55 (1) C/W Considering 6 cm of copper Board heat-sink. Doc ID 2145 Rev 20 5/30 Electrical characteristics 4 L78LxxAB, L78LxxAC, L78LxxC Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C, IO = 40 mA, CI = 0.33 F, CO = 0.1 F unless otherwise specified. Table 4. Symbol Electrical characteristics of L78L33C (VI = 8.3 V) Parameter VO Output voltage VO Output voltage VO Line regulation VO Load regulation Id Quiescent current Test conditions Min. Typ. Max. Unit TJ = 25 C 3.036 3.3 3.564 V IO = 1 to 40 mA, VI = 5.3 to 20 V 2.97 3.63 IO = 1 to 70 mA, VI = 8.3 V 2.97 3.63 VI = 5.3 to 20 V, TJ = 25 C 150 VI = 6.3 to 20 V, TJ = 25 C 100 IO = 1 to 100 mA, TJ = 25 C 60 IO = 1 to 40 mA, TJ = 25 C 30 TJ = 25 C 6 mA TJ = 125 C 5.5 mA IO = 1 to 40 mA 0.2 VI = 6.3 to 20 V 1.5 Id Quiescent current change eN Output noise voltage B =10 Hz to 100 kHz, TJ = 25 C Supply voltage rejection VI = 6.3 to 16.3 V, f = 120 Hz IO = 40 mA, TJ = 25 C SVR Vd Table 5. Symbol mV mA 41 40 V 49 dB 1.7 V Electrical characteristics of L78L05C (VI = 10 V) Parameter Output voltage VO Output voltage VO Line regulation VO Load regulation Quiescent current Id Quiescent current change eN Output noise voltage 6/30 mV Dropout voltage VO Id V Test conditions Min. Typ. Max. Unit TJ = 25 C 4.6 5 5.4 V IO = 1 to 40 mA, VI = 7 to 20 V 4.5 5.5 IO = 1 to 70 mA, VI = 10 V 4.5 5.5 V VI = 8.5 to 20 V, TJ = 25 C 200 VI = 9 to 20 V, TJ = 25 C 150 IO = 1 to 100 mA, TJ = 25 C 60 IO = 1 to 40 mA, TJ = 25 C 30 TJ = 25 C 6 mA TJ = 125 C 5.5 mA IO = 1 to 40 mA 0.2 VI = 8 to 20 V 1.5 B =10 Hz to 100 kHz, TJ = 25 C Doc ID 2145 Rev 20 mV mV mA 40 V L78LxxAB, L78LxxAC, L78LxxC Table 5. Symbol SVR Vd Table 6. Symbol Electrical characteristics of L78L05C (VI = 10 V) (continued) Parameter Supply voltage rejection Test conditions VI = 9 to 20 V, f = 120 Hz IO = 40 mA, TJ = 25 C Parameter VO Output voltage VO Line regulation VO Load regulation Quiescent current Test conditions dB 1.7 V TJ = 25 C 7.36 8 8.64 V IO = 1 to 40 mA, VI = 8.5 to 20 V 7.2 8.8 IO = 1 to 70 mA, VI = 12 V 7.2 8.8 V VI = 8.5 to 20 V, TJ = 25 C 200 VI = 9 to 20 V, TJ = 25 C 150 IO = 1 to 100 mA, TJ = 25 C 80 IO = 1 to 40 mA, TJ = 25 C 40 TJ = 25 C 6 mA TJ = 125 C 5.5 mA IO = 1 to 40 mA 0.2 VI = 8 to 20 V 1.5 B =10 Hz to 100 kHz, TJ = 25 C Supply voltage rejection VI = 9 to 20 V, f = 120 Hz IO = 40 mA, TJ = 25 C mV mV mA 36 Dropout voltage 60 V 45 dB 1.7 V Electrical characteristics of L78L09C (VI = 15 V) Parameter VO Output voltage VO Output voltage VO Line regulation VO Load regulation Id 49 Unit Output noise voltage Id 40 Max. eN Symbol Unit Typ. Quiescent current change Table 7. Max. Min. Id Vd Typ. Electrical characteristics of L78L08C (VI = 14 V) Output voltage SVR Min. Dropout voltage VO Id Electrical characteristics Quiescent current Quiescent current change Test conditions Min. Typ. Max. Unit TJ = 25 C 8.28 9 9.72 V IO = 1 to 40 mA, VI = 11.5 to 23 V 8.1 9.9 IO = 1 to 70 mA, VI = 15 V 8.1 9.9 V VI = 11.5 to 23 V, TJ = 25 C 250 VI = 12 to 23 V, TJ = 25 C 200 IO = 1 to 100 mA, TJ = 25 C 80 IO = 1 to 40 mA, TJ = 25 C 40 TJ = 25 C 6 mA TJ = 125 C 5.5 mA IO = 1 to 40 mA 0.2 VI = 12 to 23 V 1.5 Doc ID 2145 Rev 20 mV mV mA 7/30 Electrical characteristics Table 7. Symbol eN SVR Vd Table 8. Symbol Electrical characteristics of L78L09C (VI = 15 V) (continued) Parameter Test conditions Output noise voltage B =10 Hz to 100 kHz, TJ = 25 C Supply voltage rejection VI = 12 to 23 V, f = 120 Hz IO = 40 mA, TJ = 25 C Parameter VO Output voltage VO Line regulation VO Load regulation Quiescent current Test conditions TJ = 25 C dB 1.7 V Min. Typ. Max. Unit 9.2 10 10.8 V 9 11 V VI = 12.5 to 23 V, TJ = 25 C 230 VI = 13 to 23 V, TJ = 25 C 170 IO = 1 to 100 mA, TJ = 25 C 80 IO = 1 to 40 mA, TJ = 25 C 40 TJ = 25 C 6 mA TJ = 125 C 5.5 mA IO = 1 to 40 mA 0.1 VI = 13 to 23 V 1.5 B =10Hz to 100kHz, TJ = 25 C Supply voltage rejection VI = 14 to 23 V, f = 120Hz IO = 40 mA, TJ = 25 C mV mV mA 37 Dropout voltage 60 V 45 dB 1.7 V Electrical characteristics of L78L12C (VI = 19 V) Parameter VO Output voltage VO Output voltage VO Line regulation VO Load regulation 8/30 44 IO = 1 to 70 mA, VI = 16 V Output noise voltage Id V 11 eN Symbol Unit 70 9 Quiescent current change Table 9. Max. IO = 1 to 40 mA, VI = 12.5 to 23 V Id Vd 36 Typ. Electrical characteristics of L78L10C (VI = 16 V) Output voltage SVR Min. Dropout voltage VO Id L78LxxAB, L78LxxAC, L78LxxC Quiescent current Test conditions Min. Typ. Max. Unit TJ = 25 C 11.1 12 12.9 V IO = 1 to 40 mA, VI = 14.5 to 27 V 10.8 13.2 IO = 1 to 70 mA, VI = 19 V 10.8 13.2 V VI = 14.5 to 27 V, TJ = 25 C 250 VI = 16 to 27 V, TJ = 25 C 200 IO = 1 to 100 mA, TJ = 25 C 100 IO = 1 to 40 mA, TJ = 25 C 50 TJ = 25 C 6.5 mA TJ = 125 C 6 mA Doc ID 2145 Rev 20 mV mV L78LxxAB, L78LxxAC, L78LxxC Table 9. Electrical characteristics Electrical characteristics of L78L12C (VI = 19 V) (continued) Symbol Parameter Id Quiescent current change eN Output noise voltage B =10 Hz to 100 kHz, TJ = 25 C Supply voltage rejection VI = 15 to 25 V, f = 120 Hz IO = 40 mA, TJ = 25 C SVR Vd Table 10. Symbol Output voltage VO Line regulation VO Load regulation 0.2 VI = 16 to 27 V 1.5 Quiescent current Test conditions mA 36 80 V 42 dB 1.7 V Typ. Max. Unit TJ = 25 C 13.8 15 16.2 V IO = 1 to 40 mA, VI = 17.5 to 30 V 13.5 16.5 IO = 1 to 70 mA, VI = 23 V 13.5 16.5 V VI = 17.5 to 30 V, TJ = 25 C 300 VI = 20 to 30 V, TJ = 25 C 250 IO = 1 to 100 mA, TJ = 25 C 150 IO = 1 to 40 mA, TJ = 25 C 75 TJ = 25 C 6.5 mA TJ = 125 C 6 mA mV mV IO = 1 to 40 mA 0.2 VI = 20 to 30 V 1.5 Quiescent current change eN Output noise voltage B =10 Hz to 100 kHz, TJ = 25 C Supply voltage rejection VI = 18.5 to 28.5 V, f = 120 Hz IO = 40 mA, TJ = 25 C Symbol Unit Min. Id Table 11. Max. IO = 1 to 40 mA Parameter VO Vd Typ. Electrical characteristics of L78L15C (VI = 23 V) Output voltage SVR Min. Dropout voltage VO Id Test conditions mA 33 Dropout voltage 90 V 39 dB 1.7 V Electrical characteristics of L78L18C (VI = 27 V) Parameter VO Output voltage VO Output voltage VO Line regulation VO Load regulation Test conditions Min. Typ. Max. Unit TJ = 25 C 16.6 18 19.4 V IO = 1 to 40 mA, VI = 22 to 33 V 16.2 19.8 IO = 1 to 70 mA, VI = 27 V 16.2 19.8 V VI = 22 to 33 V, TJ = 25 C 320 VI = 22 to 33 V, TJ = 25 C 270 IO = 1 to 100 mA, TJ = 25 C 170 IO = 1 to 40 mA, TJ = 25 C 85 Doc ID 2145 Rev 20 mV mV 9/30 Electrical characteristics Table 11. Symbol Id L78LxxAB, L78LxxAC, L78LxxC Electrical characteristics of L78L18C (VI = 27 V) (continued) Parameter Quiescent current Test conditions Max. Unit TJ = 25 C 6.5 mA TJ = 125 C 6 mA 0.2 VI = 23 to 33 V 1.5 Quiescent current change eN Output noise voltage B =10 Hz to 100 kHz, TJ = 25 C Supply voltage rejection VI = 23 to 33 V, f = 120 Hz IO = 40 mA, TJ = 25 C Vd Table 12. Symbol Parameter VO Output voltage VO Line regulation VO Load regulation Quiescent current Test conditions V 38 dB 1.7 V Min. Typ. Max. Unit TJ = 25 C 22.1 24 25.9 V IO = 1 to 40 mA, VI = 27 to 38 V 21.6 26.4 IO = 1 to 70 mA, VI = 33 V 21.6 26.4 V VI = 27 to 38 V, TJ = 25 C 350 VI = 28 to 38 V, TJ = 25 C 300 IO = 1 to 100 mA, TJ = 25 C 200 IO = 1 to 40 mA, TJ = 25 C 100 TJ = 25 C 6.5 mA TJ = 125 C 6 mA mV mV IO = 1 to 40 mA 0.2 VI = 28 to 38 V 1.5 Id Quiescent current change eN Output noise voltage B =10 Hz to 100 kHz, TJ = 25 C Supply voltage rejection VI = 29 to 35 V, f = 120 Hz IO = 40 mA, TJ = 25 C Vd 32 120 Electrical characteristics of L78L24C (VI = 33 V) Output voltage SVR mA Dropout voltage VO Id Typ. IO = 1 to 40 mA Id SVR Min. mA 30 Dropout voltage 200 V 37 dB 1.7 V TJ = 0 to 125 C for L78L33AC, TJ = -40 to 125 C for L78L33AB. Table 13. Symbol Electrical characteristics of L78L33AB and L78L33AC (VI = 8.3 V) Parameter VO Output voltage VO Output voltage VO Line regulation 10/30 Test conditions Min. Typ. Max. Unit TJ = 25 C 3.168 3.3 3.432 V IO = 1 to 40 mA, VI = 5.3 to 20 V 3.135 3.465 IO = 1 to 70 mA, VI = 8.3 V 3.135 3.465 V VI = 5.3 to 20 V, TJ = 25 C 150 VI = 6.3 to 20 V, TJ = 25 C 100 Doc ID 2145 Rev 20 mV L78LxxAB, L78LxxAC, L78LxxC Table 13. Symbol VO Id Electrical characteristics Electrical characteristics of L78L33AB and L78L33AC (VI = 8.3 V) (continued) Parameter Load regulation Quiescent current Test conditions Max. Unit 60 IO = 1 to 40 mA, TJ = 25 C 30 TJ = 25 C 6 mA TJ = 125 C 5.5 mA IO = 1 to 40 mA 0.1 VI = 6.3 to 20 V 1.5 Quiescent current change eN Output noise voltage B =10 Hz to 100 kHz, TJ = 25 C Supply voltage rejection VI = 6.3 to 16.3 V, f = 120 Hz IO = 40 mA, TJ = 25 C Vd Typ. IO = 1 to 100 mA, TJ = 25 C Id SVR Min. mV mA 41 Dropout voltage 40 V 49 dB 1.7 V TJ = 0 to 125 C for L78L05AC, TJ = -40 to 125 C for L78L05AB. Table 14. Symbol Electrical characteristics of L78L05AB and L78L05AC (VI = 10 V) Parameter VO Output voltage VO Output voltage VO Line regulation VO Load regulation Id Quiescent current Test conditions Min. Typ. Max. Unit TJ = 25 C 4.8 5 5.2 V IO = 1 to 40 mA, VI = 7 to 20 V 4.75 5.25 IO = 1 to 70 mA, VI = 10 V 4.75 5.25 VI = 7 to 20 V, TJ = 25 C 150 VI = 8 to 20 V, TJ = 25 C 100 IO = 1 to 100 mA, TJ = 25 C 60 IO = 1 to 40 mA, TJ = 25 C 30 TJ = 25 C 6 mA TJ = 125 C 5.5 mA IO = 1 to 40 mA 0.1 VI = 8 to 20 V 1.5 Id Quiescent current change eN Output noise voltage B =10 Hz to 100 kHz, TJ = 25 C Supply voltage rejection VI = 8 to 18 V, f = 120 Hz IO = 40 mA, TJ = 25 C SVR Vd V mV mV mA 41 Dropout voltage 40 V 49 dB 1.7 V TJ = 0 to 125 C for L78L06AC, TJ = -40 to 125 C for L78L06AB. Doc ID 2145 Rev 20 11/30 Electrical characteristics Table 15. Symbol Electrical characteristics of L78L06AB and L78L06AC (VI = 12 V) Parameter VO Output voltage VO Output voltage VO Line regulation VO Load regulation Id L78LxxAB, L78LxxAC, L78LxxC Quiescent current Test conditions Min. Typ. Max. Unit TJ = 25 C 5.76 6 6.24 V IO = 1 to 40 mA, VI = 8.5 to 20 V 5.7 6.3 IO = 1 to 70 mA, VI = 12 V 5.7 6.3 VI = 8.5 to 20 V, TJ = 25 C 150 VI = 9 to 20 V, TJ = 25 C 100 IO = 1 to 100 mA, TJ = 25 C 60 IO = 1 to 40 mA, TJ = 25 C 30 TJ = 25 C 6 mA TJ = 125 C 5.5 mA IO = 1 to 40 mA 0.1 VI = 9 to 20 V 1.5 Id Quiescent current change eN Output noise voltage B =10 Hz to 100 kHz, TJ = 25 C Supply voltage rejection VI = 9 to 20 V, f = 120 Hz IO = 40 mA, TJ = 25 C SVR Vd V mV mV mA 39 Dropout voltage 50 V 46 dB 1.7 V TJ = 0 to 125 C for L78L08AC, TJ = -40 to 125 C for L78L08AB. Table 16. Symbol Electrical characteristics of L78L08AB and L78L08AC (VI = 14 V) Parameter VO Output voltage VO Output voltage VO Line regulation VO Load regulation Id Quiescent current Test conditions Min. Typ. Max. Unit TJ = 25 C 7.68 8 8.32 V IO = 1 to 40 mA, VI = 10.5 to 23 V 7.6 8.4 IO = 1 to 70 mA, VI = 14 V 7.6 8.4 VI = 10.5 to 23 V, TJ = 25 C 175 VI = 11 to 23 V, TJ = 25 C 125 IO = 1 to 100 mA, TJ = 25 C 80 IO = 1 to 40 mA, TJ = 25 C 40 TJ = 25 C 6 mA TJ = 125 C 5.5 mA IO = 1 to 40 mA 0.1 VI = 11 to 23 V 1.5 Id Quiescent current change eN Output noise voltage B =10 Hz to 100 kHz, TJ = 25 C Supply voltage rejection VI = 12 to 23 V, f = 120 Hz IO = 40 mA, TJ = 25 C SVR Vd 12/30 V Dropout voltage Doc ID 2145 Rev 20 mV mV mA 37 60 V 45 dB 1.7 V L78LxxAB, L78LxxAC, L78LxxC Electrical characteristics TJ = 0 to 125 C for L78L09AC, TJ = -40 to 125 C for L78L09AB. Table 17. Symbol Electrical characteristics of L78L09AB and L78L09AC (VI = 15 V) Parameter VO Output voltage VO Output voltage VO Line regulation VO Load regulation Id Quiescent current Test conditions Min. Typ. Max. Unit TJ = 25 C 8.64 9 9.36 V IO = 1 to 40 mA, VI = 11.5 to 23 V 8.55 9.45 IO = 1 to 70 mA, VI = 15 V 8.55 9.45 VI = 11.5 to 23 V, TJ = 25 C 225 VI = 12 to 23 V, TJ = 25 C 150 IO = 1 to 100 mA, TJ = 25 C 80 IO = 1 to 40 mA, TJ = 25 C 40 TJ = 25 C 6 mA TJ = 125 C 5.5 mA IO = 1 to 40 mA 0.1 VI = 12 to 23 V 1.5 Id Quiescent current change eN Output noise voltage B =10 Hz to 100 kHz, TJ = 25 C Supply voltage rejection VI = 12 to 23 V, f = 120 Hz IO = 40 mA, TJ = 25 C SVR Vd V mV mV mA 37 Dropout voltage 70 V 44 dB 1.7 V TJ = 0 to 125 C for L78L10AC, TJ = -40 to 125 C for L78L10AB. Table 18. Symbol Electrical characteristics of L78L10AC (VI = 16 V) Parameter VO Output voltage VO Output voltage VO Line regulation VO Load regulation Id Quiescent current Test conditions Min. Typ. Max. Unit TJ = 25 C 9.6 10 10.4 V IO = 1 to 40 mA, VI = 12.5 to 23 V 9.5 10.5 IO = 1 to 70 mA, VI = 16 V 9.5 10.5 VI = 12.5 to 23 V, TJ = 25 C 230 VI = 13 to 23 V, TJ = 25 C 170 IO = 1 to 100 mA, TJ = 25 C 80 IO = 1 to 40 mA, TJ = 25 C 40 TJ = 25 C 6 mA TJ = 125 C 5.5 mA IO = 1 to 40 mA 0.1 VI = 13 to 23 V 1.5 Id Quiescent current change eN Output noise voltage B =10 Hz to 100 kHz, TJ = 25 C Supply voltage rejection VI = 14 to 23 V, f = 120 Hz IO = 40 mA, TJ = 25 C SVR Vd V Dropout voltage Doc ID 2145 Rev 20 mV mV mA 37 60 V 45 dB 1.7 V 13/30 Electrical characteristics L78LxxAB, L78LxxAC, L78LxxC TJ = 0 to 125 C for L78L12AC, TJ = -40 to 125 C for L78L12AB. Table 19. Symbol Electrical characteristics of L78L12AB and L78L12AC (VI = 19 V) Parameter VO Output voltage VO Output voltage VO Line regulation VO Load regulation Id Quiescent current Test conditions Min. Typ. Max. Unit TJ = 25 C 11.5 12 12.5 V IO = 1 to 40 mA, VI = 14.5 to 27 V 11.4 12.6 IO = 1 to 70 mA, VI = 19 V 11.4 12.6 VI = 14.5 to 27 V, TJ = 25 C 250 VI = 16 to 27 V, TJ = 25 C 200 IO = 1 to 100 mA, TJ = 25 C 100 IO = 1 to 40 mA, TJ = 25 C 50 TJ = 25 C 6.5 mA TJ = 125 C 6 mA mV 0.1 VI = 16 to 27 V 1.5 Quiescent current change eN Output noise voltage B =10 Hz to 100 kHz, TJ = 25 C Supply voltage rejection VI = 15 to 25 V, f = 120 Hz IO = 40 mA, TJ = 25 C Vd mV IO = 1 to 40 mA Id SVR V mA 37 Dropout voltage 80 V 42 dB 1.7 V TJ = 0 to 125 C for L78L15AC, TJ = -40 to 125 C for L78L15AB. Table 20. Symbol Electrical characteristics of L78L15AB and L78L15AC (VI = 23 V) Parameter VO Output voltage VO Output voltage VO Line regulation VO Load regulation Id Quiescent current Test conditions Min. Typ. Max. Unit TJ = 25 C 14.4 15 15.6 V IO = 1 to 40 mA, VI = 17.5 to 30 V 14.25 15.75 IO = 1 to 70 mA, VI = 23 V 14.25 15.75 VI = 17.5 to 30 V, TJ = 25 C 300 VI = 20 to 30 V, TJ = 25 C 250 IO = 1 to 100 mA, TJ = 25 C 150 IO = 1 to 40 mA, TJ = 25 C 75 TJ = 25 C 6.5 mA TJ = 125 C 6 mA VI = 20 to 30 V 1.5 eN Output noise voltage B =10 Hz to 100 kHz, TJ = 25 C Supply voltage rejection VI = 18.5 to 28.5 V, f = 120 Hz IO = 40 mA, TJ = 25 C 14/30 mV 0.1 Quiescent current change Vd mV IO = 1 to 40 mA Id SVR V Dropout voltage Doc ID 2145 Rev 20 mA 34 90 V 39 dB 1.7 V L78LxxAB, L78LxxAC, L78LxxC Electrical characteristics TJ = 0 to 125 C for L78L18AC, TJ = -40 to 125 C for L78L18AB. Table 21. Symbol Electrical characteristics of L78L18AC (VI = 27 V) Parameter VO Output voltage VO Output voltage VO Line regulation VO Load regulation Id Quiescent current Test conditions Min. Typ. Max. Unit TJ = 25 C 17.3 18 18.7 V IO = 1 to 40 mA, VI = 22 to 33 V 17.1 18.9 IO = 1 to 70 mA, VI = 27 V 17.1 18.9 VI = 22 to 33 V, TJ = 25 C 320 VI = 22 to 33 V, TJ = 25 C 270 IO = 1 to 100 mA, TJ = 25 C 170 IO = 1 to 40 mA, TJ = 25 C 85 TJ = 25 C 6.5 mA TJ = 125 C 6 mA mV 0.1 VI = 23 to 33 V 1.5 Quiescent current change eN Output noise voltage B =10 Hz to 100 kHz, TJ = 25 C Supply voltage rejection VI = 23 to 33 V, f = 120 Hz IO = 40 mA, TJ = 25 C Vd mV IO = 1 to 40 mA Id SVR V mA 33 Dropout voltage 120 V 38 dB 1.7 V TJ = 0 to 125 C for L78L24AC, TJ = -40 to 125 C for L78L24AB. Table 22. Symbol Electrical characteristics of L78L24AB and L78L24AC (VI = 33 V) Parameter VO Output voltage VO Output voltage VO Line regulation VO Load regulation Id Quiescent current Test conditions TJ = 25 C Max. Unit 23 24 25 V 22.8 25.2 IO = 1 to 70 mA, VI = 33 V 22.8 25.2 V VI = 27 to 38 V, TJ = 25 C 350 VI = 28 to 38 V, TJ = 25 C 300 IO = 1 to 100 mA, TJ = 25 C 200 IO = 1 to 40 mA, TJ = 25 C 100 TJ = 25 C 6.5 mA TJ = 125 C 6 mA mV mV IO = 1 to 40 mA 0.1 VI = 28 to 38 V 1.5 Quiescent current change eN Output noise voltage B =10 Hz to 100 kHz, TJ = 25 C Supply voltage rejection VI = 29 to 33 V, f = 120 Hz IO = 40 mA, TJ = 25 C Vd Typ. IO = 1 to 40 mA, VI = 27 to 38 V Id SVR Min. Dropout voltage Doc ID 2145 Rev 20 mA 31 200 V 37 dB 1.7 V 15/30 Typical performance L78LxxAB, L78LxxAC, L78LxxC 5 Typical performance Figure 4. L78L05/12 output voltage vs. ambient temperature Figure 5. L78L05/12/24 load characteristics Figure 6. L78L05/12/24 thermal shutdown Figure 7. L78L05/12 quiescent current vs. output current 16/30 Doc ID 2145 Rev 20 L78LxxAB, L78LxxAC, L78LxxC Figure 8. Typical performance L78L05 quiescent current vs. input Figure 9. voltage Figure 10. L78L05/12/24 ripple rejection L78L05/12/24 output characteristics Figure 11. L78L05 dropout characteristics Figure 12. L78Lxx short-circuit output current Doc ID 2145 Rev 20 17/30 Typical application 6 L78LxxAB, L78LxxAC, L78LxxC Typical application Figure 13. High output current short-circuit protected Figure 14. Edit boost circuit Figure 15. Current regulator 18/30 Doc ID 2145 Rev 20 L78LxxAB, L78LxxAC, L78LxxC Typical application Figure 16. Adjustable output regulator Doc ID 2145 Rev 20 19/30 Package mechanical data 7 L78LxxAB, L78LxxAC, L78LxxC Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. 20/30 Doc ID 2145 Rev 20 L78LxxAB, L78LxxAC, L78LxxC Package mechanical data SO-8 mechanical data Dim. mm. Min. Typ. inch. Max. Min. Typ. Max. A 1.35 1.75 0.053 0.069 A1 0.10 0.25 0.04 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 4.80 5.00 0.189 0.197 E 3.80 4.00 0.150 0.157 e 1.27 0.050 H 5.80 6.20 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 k ddd 8 (max.) 0.1 0.04 0016023/C Doc ID 2145 Rev 20 21/30 Package mechanical data L78LxxAB, L78LxxAC, L78LxxC SOT-89 mechanical data mm. mils. Dim. Min. Typ. Max. Min. Typ. Max. A 1.4 1.6 55.1 63.0 B 0.44 0.56 17.3 22.0 B1 0.36 0.48 14.2 18.9 C 0.35 0.44 13.8 17.3 C1 0.35 0.44 13.8 17.3 D 4.4 4.6 173.2 181.1 D1 1.62 1.83 63.8 72.0 E 2.29 2.6 90.2 102.4 e 1.42 1.57 55.9 61.8 e1 2.92 3.07 115.0 120.9 H 3.94 4.25 155.1 167.3 L 0.89 1.2 35.0 47.2 P025H 22/30 Doc ID 2145 Rev 20 L78LxxAB, L78LxxAC, L78LxxC Package mechanical data TO-92 mechanical data mm. mils. Dim. Min. Typ. Max. Min. Typ. Max. A 4.32 4.95 170.1 194.9 b 0.36 0.51 14.2 20.1 D 4.45 4.95 175.2 194.9 E 3.30 3.94 129.9 155.1 e 2.41 2.67 94.9 105.1 e1 1.14 1.40 44.9 55.1 L 12.7 15.49 500.0 609.8 R 2.16 2.41 85.0 94.9 S1 0.92 1.52 36.2 59.8 W 0.41 0.56 16.1 22.0 5 5 0102782/D Doc ID 2145 Rev 20 23/30 Package mechanical data L78LxxAB, L78LxxAC, L78LxxC Tape & reel SO-8 mechanical data mm. inch. Dim. Min. A Max. Min. 330 13.2 Typ. Max. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 24/30 Typ. 0.504 22.4 0.519 0.882 Ao 8.1 8.5 0.319 0.335 Bo 5.5 5.9 0.216 0.232 Ko 2.1 2.3 0.082 0.090 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 Doc ID 2145 Rev 20 L78LxxAB, L78LxxAC, L78LxxC Package mechanical data Tape & reel SOT-89 mechanical data mm. inch. Dim. Min. Typ. A Max. Min. Typ. 180 13.0 7.086 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 Max. 0.504 0.512 14.4 0.519 0.567 Ao 4.70 4.80 4.90 0.185 0.189 0.193 Bo 4.30 4.40 4.50 0.169 0.173 0.177 Ko 1.70 1.80 1.90 0.067 0.071 0.075 Po 3.9 4.0 4.1 0.153 0.157 0.161 P 7.9 8.0 8.1 0.311 0.315 0.319 Doc ID 2145 Rev 20 25/30 Package mechanical data Table 23. L78LxxAB, L78LxxAC, L78LxxC Tape and reel TO-92 mechanical data mm. inch. Dim. Min. Typ. Max. Min. Typ. A1 (1) 4.80 0.189 T (1) 3.80 0.150 T1 1.60 0.063 T2 2.30 0.091 d 0.48 0.019 Max. P0 12.5 12.9 0.492 0.508 P2 5.65 7.05 0.222 0.278 F1, F2 2.44 2.94 0.096 delta H 2.54 2 W 17.5 W0 W1 18.00 0.079 0.689 5.7 6.3 0.224 0.248 8.5 9.25 0.335 0.364 0.50 H 18.50 15.50 H1 D0 0.748 0.20 18.70 16.50 0.728 0.610 25.00 3.8 0.709 0.726 0.650 0.984 4.2 0.150 0.165 t 0.90 0.035 L1 3 0.118 delta P 1 0.039 u 50 1.968 1 360 14.173 2 30 1.181 1. For the MAX and MIN values refer to the TO-92 mechanical data on page 23. 26/30 0.116 19.0 W2 H0 0.100 Doc ID 2145 Rev 20 L78LxxAB, L78LxxAC, L78LxxC Package mechanical data Figure 17. Tape and reel TO-92 drawing dimension delta P T A1 T2 H1 T1 delta H H H0 d L W2 l1 W0 W W1 F1 F2 P2 D0 t P0 DRAWING NOT IN SCALE Doc ID 2145 Rev 20 27/30 Order codes L78LxxAB, L78LxxAC, L78LxxC 8 Order codes Table 24. Order codes Packages Part numbers SO-8 TO92 (BAG) (1) L78L33C L78L33CD-TR 3.3 V L78L33AC L78L33ACD13TR L78L33ACZ L78L33ACUTR 3.3 V L78L33AB L78L33ABD-TR L78L33ABZ L78L33ABUTR 3.3 V L78L05C L78L05CD13TR L78L05CZ L78L05AC L78L05ACD13TR L78L05ACZ L78L05ACUTR 5V L78L05AB L78L05ABD13TR L78L05ABZ L78L05ABUTR 5V L78L06AC L78L06ACD13TR L78L06ACZ L78L06ACUTR 6V L78L06AB L78L06ABD13TR L78L06ABZ L78L06ABUTR 6V L78L08C L78L08CD13TR L78L08AC L78L08ACD13TR L78L08ACZ L78L08ACUTR 8V L78L08AB L78L08ABD13TR L78L08ABZ L78L08ABUTR 8V L78L09C L78L09CD13TR L78L09AC L78L09ACD13TR L78L09ACZ L78L09ACUTR 9V L78L09AB L78L09ABD13TR L78L09ABZ L78L09ABUTR 9V L78L10ACUTR 10 V 5V 8V 9V L78L10AC L78L12C L78L12CD13TR L78L12AC L78L12ACD13TR L78L12ACZ L78L12ACUTR 12 V L78L12AB L78L12ABD-TR L78L12ABZ L78L12ABUTR 12 V L78L15C L78L15CD-TR L78L15AC L78L15ACD13TR L78L15AB L78L18C 12 V 15 V L78L15ACZ L78L15ACUTR 15 V L78L15ABZ L78L15ABUTR 15 V L78L18CD13TR 18 V L78L18AC L78L24C 1. Output voltages SOT-89 L78L18ACUTR L78L24CD-TR 18 V 24 V L78L24AC L78L24ACZ L78L24AB L78L24ABZ L78L24ACUTR 24 V 24 V Available in Ammopak with the suffix "-AP" or in tape and reel with the suffix "TR". Please note that in these cases pins are shaped according to tape and reel specifications. 28/30 Doc ID 2145 Rev 20 L78LxxAB, L78LxxAC, L78LxxC 9 Revision history Table 25. Document revision history Revision history Date Revision Changes 14-Mar-2005 9 Add tape and reel for TO-92. 15-Mar-2005 10 Add note on Table 3. 23-Dec-2005 11 Mistake on ordering Table in header. 12-Sep-2006 12 Order codes updated. 07-Jun-2007 13 Order codes updated. 18-Sep-2007 14 Added Table 1 in cover page. 15-Jul-2008 15 Modified: Table 1 on page 1 and Table 24 on page 28. 18-Aug-2008 16 Modified Figure 12 on page 17. 03-Apr-2009 17 Added: RthJA value for SOT-89 Table 3 on page 5. 08-Feb-2011 18 Added note Table 23 on page 26 21-Feb-2012 19 Modified: SOT-89 Figure 2 on page 4. 14-Aug-2012 20 Updated TOP value for L78L00AC in Table 2 on page 5. Minor text changes. Doc ID 2145 Rev 20 29/30 L78LxxAB, L78LxxAC, L78LxxC Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2012 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 30/30 Doc ID 2145 Rev 20