AUIRF4905
HEXFET® Power MOSFET
AUTOMOTIVE GRADE
www.irf.com 1
11/10/10
Features
lAdvanced Planar Technology
lLow On-Resistance
lDynamic dV/dT Rating
l175°C Operating Temperature
lFast Switching
lFully Avalanche Rated
lRepetitive Avalanche Allowed up to Tjmax
lLead-Free, RoHS Compliant
lAutomotive Qualified *
Specifically designed for Automotive applications, this cellular
design of HEXFET® Power MOSFETs utilizes the latest
processing techniques to achieve low on-resistance per silicon
area. This benefit combined with the fast switching speed and
ruggedized device design that HEXFET power MOSFETs are
well known for, provides the designer with an extremely
efficient and reliable device for use in Automotive and a wide
variety of other applications.
Description
GDS
Gate Drain Source
Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress
ratings only; and functional operation of the device at these or any other condition beyond those indicated in the specifications
is not implied.Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The thermal
resistance and power dissipation ratings are measured under board mounted and still air conditions. Ambient temperature (TA)
is 25°C, unless otherwise specified.
HEXFET® is a registered trademark of International Rectifier.
*Qualification standards can be found at http://www.irf.com/
V
(BR)DSS
- 55V
R
DS(on)
max. 0.02Ω
I
D
-74A
Parameter Units
I
D
@ T
C
= 25°C Continuous Drain Current, V
GS
@ -10V
I
D
@ T
C
= 100°C Continuous Drain Current, V
GS
@ -10V
I
DM
Pulsed Drain Current
c
P
D
@T
C
= 25°C Power Dissipation W
Linear Derating Factor W/°C
V
GS
Gate-to-Source Voltage V
E
AS
Single Pulse Avalanche Energy(Thermally limited)
d
I
AR
Avalanche Current
c
A
E
AR
Repetitive Avalanche Energy
c
mJ
dv/dt Peak Diode Recovery dv/dt
e
V/ns
T
J
Operating Junction and
T
STG
Storage Temperature Range
Soldering Temperature, for 10 seconds(1.6mm from case )
Mounting Torque, 6-32 or M3 screw
Thermal Resistance
Parameter Typ. Max. Units
R
θJC
Junction-to-Case
i
––– 0.75
R
θCS
Case-to-Sink, Flat, Greased Surface 0.50 ––– °C/W
R
θJA
Junction-to-Ambient ––– 62
-5.0
-55 to + 175
300
10 lbf
y
in (1.1N
y
m)
Max.
-74
-52
-260
mJ
°C
A
20
930
-38
200
1.3
± 20
TO-220AB
AUIRF4905
D
S
D
G
S
D
G
PD - 96338
AUIRF4905
www.irf.com 2
S
D
G
S
D
G
Repetitive rating; pulse width limited by max. junction temperature. ( See fig. 11 )
Starting TJ = 25°C, L = 1.3mH RG = 25Ω, IAS = -38A. (See Figure 12)
ISD ≤ -38A, di/dt ≤ -270A/µs, VDD ≤ V(BR)DSS, TJ ≤ 175°C
Pulse width ≤ 300µs; duty cycle ≤ 2%.
Notes:
Static Electrical Characteristics @ T
J
= 25°C (unless otherwise specified)
Parameter Min. T
y
p. Max. Units
V
(BR)DSS
Drain-to-Source Breakdown Volta
g
e -55 ––– ––– V
∆V
(BR)DSS
/
∆T
J
Breakdown Volta
g
e Temp. Coefficient ––– -0.05 ––– V/°C
R
DS(on)
Static Drain-to-Source On-Resistance ––– ––– 0.02 Ω
V
GS(th)
Gate Threshold Volta
g
e -2.0 ––– -4.0 V
g
fs Forward Transconductance 21 ––– ––– S
I
DSS
Drain-to-Source Leaka
g
e Current ––– ––– -25
µ
A
––– ––– -250
I
GSS
Gate-to-Source Forward Leaka
e ––– ––– 100 nA
Gate-to-Source Reverse Leaka
g
e––––––-100
Dynamic Electrical Characteristics @ T
J
= 25°C (unless otherwise specified)
Q
g
Total Gate Char
g
e––––––180
Q
gs
Gate-to-Source Char
g
e––––––32nC
Q
gd
Gate-to-Drain ("Miller") Char
g
e––––––86
t
d(on)
Turn-On Dela
y
Time ––– 18 –––
t
r
Rise Time ––– 99 –––
t
d(off)
Turn-Off Dela
y
Time ––– 61 ––– ns
t
f
Fall Time ––– 96 –––
L
D
Internal Drain Inductance Between lead,
nH 6mm (0.25in.)
L
S
Internal Source Inductance from packa
g
e
and center of die contact
C
iss
Input Capacitance ––– 3400 –––
C
oss
Output Capacitance ––– 1400 –––
C
rss
Reverse Transfer Capacitance ––– 640 ––– pF
Diode Characteristics
Parameter Min. T
y
p. Max. Units
I
S
Continuous Source Current
(Body Diode) A
I
SM
Pulsed Source Current
(Body Diode)
c
V
SD
Diode Forward Volta
g
e ––– ––– -1.6 V
t
rr
Reverse Recover
y
Time ––– 89 130 ns
Q
rr
Reverse Recover
y
Char
g
e ––– 230 350 nC
t
on
Forward Turn-On Time
Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
––– ––– -74
––– ––– -260
–––
–––
–––
–––
4.5
7.5
V
GS
= -10V , See Fig.6 and 13
f
V
DD
= -28V
ID = -38A
R
G
= 2.5 Ω
T
J
= 25°C, I
S
=-38A , V
GS
= 0V
f
T
J
= 25°C, I
F
=-38A
di/dt = -100A/
µ
s
f
Conditions
V
GS
= 0V, I
D
= -250µA
Reference to 25°C, I
D
= -1mA
V
GS
= -10V, I
D
= -38A
f
V
DS
= V
GS
, I
D
= -250µA
V
DS
= -55V, V
GS
= 0V
V
DS
= -44V, V
GS
= 0V, T
J
= 150°C
MOSFET symbol
showing the
integral reverse
p-n junction diode.
V
DS
= -25V, I
D
= -38A
I
D
= -38A
V
DS
= -44V
Conditions
R
D
=0.72 Ω See Fig. 10
f
V
GS
= 0V
V
DS
= -25V
ƒ = 1.0MHz, See Fig.5
V
GS
= 20V
V
GS
= -20V
AUIRF4905
www.irf.com 3
Qualification standards can be found at International Rectifiers web site: http//www.irf.com/
 Exceptions to AEC-Q101 requirements are noted in the qualification report.
Qualification Information
†
Moisture Sensitivity Level 3L-TO-220 N/A
Qualification Level
Automotive
(per AEC-Q101)
††
Comments: This part number(s) passed Automotive qualification.
IR’s Industrial and Consumer qualification level is granted by
extension of the higher Automotive level.
Charged Device Model
Class C5 (1125V)
(per AEC-Q101-005)
RoHS Compliant Yes
ESD
Machine Model
Class M4 (425V)
(per AEC-Q101-002)
Human Body Model
Class H2 (4000V)
(per AEC-Q101-001)
AUIRF4905
www.irf.com 4
Fig 4. Normalized On-Resistance
Vs. Temperature
Fig 1. Typical Output Characteristics
Fig 3. Typical Transfer Characteristics
1
10
100
1000
0.1 1 10 100
D
DS
20µs PULSE WIDTH
T = 25°C
c
A
-I , Drain-to-Source Current (A)
-V , Drain-to-Source Voltage (V)
VGS
TOP - 15V
- 10V
- 8.0V
- 7.0V
- 6.0V
- 5.5V
- 5.0V
BOTTOM - 4. 5V
-4.5V
1
10
100
1000
0.1 1 10 100
D
DS
A
-I , Drain-to-Source Current (A)
-V , Drain-to-Source Voltage (V)
VGS
TOP - 15V
- 10V
- 8.0V
- 7.0V
- 6.0V
- 5.5V
- 5.0V
BOTTOM - 4.5V
-4.5V
20µs PULSE WIDTH
T = 175°C
C
1
10
100
1000
45678910
T = 25°C
J
GS
D
A
-I , Drain-to-Source Current (A)
-V , Gate-to-Source Voltage (V)
V = -25V
20µs PULSE WIDTH
DS
T = 175°C
J
0.0
0.5
1.0
1.5
2.0
-60 -40 -20 0 20 40 60 80 100 120 140 160 180
J
T , Junction Temperature (°C)
R , Drain-to-Source On Resistance
DS(on)
(Normalized)
A
V = -10V
GS
I = -64A
D
Fig 2. Typical Output Characteristics
AUIRF4905
www.irf.com 5
Fig 8. Maximum Safe Operating Area
Fig 6. Typical Gate Charge Vs.
Gate-to-Source Voltage
Fig 5. Typical Capacitance Vs.
Drain-to-Source Voltage
Fig 7. Typical Source-Drain Diode
Forward Voltage
0
1000
2000
3000
4000
5000
6000
7000
1 10 100
C, Capacitance (pF)
A
DS
-V , Drain-to-Source Voltage (V)
V = 0V, f = 1MHz
C = C + C , C SHORTED
C = C
C = C + C
GS
iss gs gd ds
rss gd
oss ds gd
C
iss
C
oss
C
rss
0
4
8
12
16
20
0 40 80 120 160 200
G
GS
A
-V , Gate-to-Source Voltage (V)
Q , Total Gate Charge (nC)
FOR TEST CIRCUIT
SEE FIGURE 13
I = -38A
V = -44V
V = -28V
D
DS
DS
1
10
100
1000
0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8
T = 25°C
J
V = 0V
GS
SD
SD
A
-I , Reverse Drain Current (A)
-V , Source-to-Drain Voltage (V)
T = 175°C
J
1
10
100
1000
1 10 100
OPERATION IN THIS AREA LIMITED
BY R
DS(on)
10ms
A
-I , Drain Current (A)
-V , Drain-to-Source Voltage (V)
DS
D
100µs
1ms
T = 25°C
T = 175°C
Single Pulse
C
J
AUIRF4905
www.irf.com 6
Fig 10a. Switching Time Test Circuit
Fig 10b. Switching Time Waveforms
Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case
Fig 9. Maximum Drain Current Vs.
Case Temperature
V
DS
90%
10%
V
GS
t
d(on)
t
r
t
d(off)
t
f
25 50 75 100 125 150 175
0
20
40
60
80
T , Case Temperature ( C)
I , Drain Current (A)
°
C
D
0.01
0.1
1
0.00001 0.0001 0.001 0.01 0.1 1
Notes:
1. Duty factor D = t / t
2. Peak T = P x Z + T
1 2
JDM thJC C
P
t
t
DM
1
2
t , Rectangular Pulse Duration (sec)
Thermal Response (Z )
1
thJC
0.01
0.02
0.05
0.10
0.20
D = 0.50
SINGLE PULSE
(THERMAL RESPONSE)
VDS
-10V
Pulse Width ≤ 1 µs
Duty Factor ≤ 0.1 %
RD
VGS
VDD
RG
D.U.T.
+
-
AUIRF4905
www.irf.com 7
Fig 13b. Gate Charge Test Circuit
Fig 13a. Basic Gate Charge Waveform
Fig 12c. Maximum Avalanche Energy
Vs. Drain Current
D.U.T. VDS
ID
IG
-3mA
VGS
.3µF
50KΩ
.2µF
12V
Current Regulator
Same Type as D.U.T.
Current Sampling Resistors
+
-
Fig 12b. Unclamped Inductive Waveforms
Fig 12a. Unclamped Inductive Test Circuit
tp
V
(
BR
)
DSS
I
AS
R
G
I
AS
0.01
Ω
t
p
D.U.T
L
V
DS
V
DD
DRIVER
A
15V
-20V
0
500
1000
1500
2000
2500
25 50 75 100 125 150 175
J
E , Single Pulse Avalanche Energy (mJ)
AS
A
Starting T , Junction Temperature (°C)
I
TOP -16A
-27A
BOTTOM -38A
D
Q
G
Q
GS
Q
GD
V
G
Charge
-10V
AUIRF4905
www.irf.com 8
Fig 14. For P-Channel HEXFETS
Peak Diode Recovery dv/dt Test Circuit
P.W. Period
di/dt
Diode Recovery
dv/dt
Ripple ≤5%
Body Diode Forward Drop
Re-Applied
Voltage
Reverse
Recovery
Current
Body Diode Forward
Current
V
GS
=10V
V
DD
I
SD
Driver Gate Drive
D.U.T. I
SD
Waveform
D.U.T. V
DS
Waveform
Inductor Curent
D = P. W .
Period
[ ]
[ ]
*** VGS = 5.0V for Logic Level and 3V Drive Devices
[ ] ***
+
-
+
+
+
-
-
-
RG
VDD
• dv/dt controlled by RG
• ISD controlled by Duty Factor "D"
• D.U.T. - Device Under Test
D.U.T*Circuit Layout Considerations
• Low Stray Inductance
• Ground Plane
• Low Leakage Inductance
Current Transformer
* Reverse Polarity of D.U.T for P-Channel
VGS
AUIRF4905
www.irf.com 9
TO-220AB Package Outline
Dimensions are shown in millimeters (inches)
TO-220AB Part Marking Information
Note: For the most current drawing please refer to IR website at http://www.irf.com/package/
YWWA
XX or XX
Part Number
IR Logo
Lot Code
AUF4905
Date Code
Y= Year
WW= Work Week
A= Automotive, Lead Free
AUIRF4905
www.irf.com 10
Ordering Information
Base part Package Type Standard Pack Complete Part Number
Form Quantity
AUIRF4905 TO-220 Tube 50 AUIRF4905
AUIRF4905
www.irf.com 11
IMPORTANT NOTICE
Unless specifically designated for the automotive market, International Rectifier Corporation and its subsidiaries (IR) reserve the right
to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and
to discontinue any product or services without notice. Part numbers designated with the “AU” prefix follow automotive industry and
/ or customer specific requirements with regards to product discontinuance and process change notification. All products are sold
subject to IR’s terms and conditions of sale supplied at the time of order acknowledgment.
IR warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with IR’s standard
warranty. Testing and other quality control techniques are used to the extent IR deems necessary to support this warranty. Except
where mandated by government requirements, testing of all parameters of each product is not necessarily performed.
IR assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using IR components. To minimize the risks with customer products and applications, customers should provide
adequate design and operating safeguards.
Reproduction of IR information in IR data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alterations is
an unfair and deceptive business practice. IR is not responsible or liable for such altered documentation. Information of third parties
may be subject to additional restrictions.
Resale of IR products or serviced with statements different from or beyond the parameters stated by IR for that product or service
voids all express and any implied warranties for the associated IR product or service and is an unfair and deceptive business practice.
IR is not responsible or liable for any such statements.
IR products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body,
or in other applications intended to support or sustain life, or in any other application in which the failure of the IR product could create
a situation where personal injury or death may occur. Should Buyer purchase or use IR products for any such unintended or
unauthorized application, Buyer shall indemnify and hold International Rectifier and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly
or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges
that IR was negligent regarding the design or manufacture of the product.
IR products are neither designed nor intended for use in military/aerospace applications or environments unless the IR products are
specifically designated by IR as military-grade or “enhanced plastic.” Only products designated by IR as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of IR products which IR has not designated as military-grade is
solely at the Buyer’s risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection
with such use.
IR products are neither designed nor intended for use in automotive applications or environments unless the specific IR products are
designated by IR as compliant with ISO/TS 16949 requirements and bear a part number including the designation “AU”. Buyers
acknowledge and agree that, if they use any non-designated products in automotive applications, IR will not be responsible for any
failure to meet such requirements
For technical support, please contact IR’s Technical Assistance Center
http://www.irf.com/technical-info/
WORLD HEADQUARTERS:
233 Kansas St., El Segundo, California 90245
Tel: (310) 252-7105
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
International Rectifier:
AUIRF4905 AUIRF4905L