TECHNICAL DATA IN74HC253 Dual 4-Input Data Selector/Multiplexer with 3-State Otputs High-Performance Silicon-Gate CMOS The IN74HC253 is identical in pinout to the LS/ALS253. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LS/ALSTTL outputs. The Address Inputs select one of four Data Inputs from each multiplexer. Each multiplexer has an active-low Output Enable control and a three-state noninverting output. * Outputs Directly Interface to CMOS, NMOS, and TTL * Operating Voltage Range: 2.0 to 6.0 V * Low Input Current: 1.0 A * High Noise Immunity Characteristic of CMOS Devices ORDERING INFORMATION IN74HC253N Plastic IN74HC253D SOIC TA = -55 to 125 C for all packages LOGIC DIAGRAM PIN ASSIGNMENT FUNCTION TABLE Inputs PIN 16 =VCC PIN 8 = GND Output A1 A0 OE Y X X H Z L L L D0 L H L D1 H L L D2 H H L D3 D0,D1...D3=the level of the respective Data Input Z = high impedance X = don't care 316 IN74HC253 MAXIMUM RATINGS* Symbol Parameter Value Unit -0.5 to +7.0 V VCC DC Supply Voltage (Referenced to GND) VIN DC Input Voltage (Referenced to GND) -1.5 to VCC +1.5 V DC Output Voltage (Referenced to GND) -0.5 to VCC +0.5 V DC Input Current, per Pin 20 mA IOUT DC Output Current, per Pin 25 mA ICC DC Supply Current, VCC and GND Pins 50 mA PD Power Dissipation in Still Air, Plastic DIP+ SOIC Package+ 750 500 mW -65 to +150 C 260 C VOUT IIN Tstg TL Storage Temperature Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package) * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. +Derating - Plastic DIP: - 10 mW/C from 65 to 125C SOIC Package: : - 7 mW/C from 65 to 125C RECOMMENDED OPERATING CONDITIONS Symbol VCC VIN, VOUT Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage, Output Voltage (Referenced to GND) TA Operating Temperature, All Package Types tr, tf Input Rise and Fall Time (Figure 1) VCC =2.0 V VCC =4.5 V VCC =6.0 V Min Max Unit 2.0 6.0 V 0 VCC V -55 +125 C 0 0 0 1000 500 400 ns This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND(VIN or VOUT)VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. 317 IN74HC253 DC ELECTRICAL CHARACTERISTICS(Voltages Referenced to GND) VCC V 25 C to -55C 85 C 125 C Unit VOUT=0.1 V or VCC-0.1 V IOUT 20 A 2.0 4.5 6.0 1.5 3.15 4.2 1.5 3.15 4.2 1.5 3.15 4.2 V Maximum Low Level Input Voltage VOUT=0.1 V or VCC-0.1 V IOUT 20 A 2.0 4.5 6.0 0.3 0.9 1.2 0.3 0.9 1.2 0.3 0.9 1.2 V Minimum High-Level Output Voltage VIN=VIH or VIL IOUT 20 A 2.0 4.5 6.0 1.9 4.4 5.9 1.9 4.4 5.9 1.9 4.4 5.9 V 4.5 6.0 3.98 5.48 3.84 5.34 3.7 5.2 2.0 4.5 6.0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 VIN=VIH or VIL IOUT 4.0 mA IOUT 5.2 mA 4.5 6.0 0.26 0.26 0.33 0.33 0.4 0.4 Symbol Parameter VIH Minimum High-Level Input Voltage VIL VOH Test Conditions VIN=VIH or VIL IOUT 4.0 mA IOUT 5.2 mA VOL 318 Guaranteed Limit Maximum Low-Level Output Voltage VIN=VIH or VIL IOUT 20 A V IIN Maximum Input Leakage Current VIN=VCC or GND 6.0 0.1 1.0 1.0 A IOZ Maximum ThreeState Leakage Current Output in High-Impedance State VIN= VIL or VIH VOUT=VCC or GND 6.0 0.5 5.0 10 A ICC Maximum Quiescent Supply Current (per Package) VIN=VCC or GND IOUT=0A 6.0 8.0 80 160 A IN74HC253 AC ELECTRICAL CHARACTERISTICS(CL=50pF,Input tr=tf=6.0 ns) Guaranteed Limit VCC Symbol Parameter V 25 C to -55C 85C 125C Unit tPLH, tPHL Maximum Propagation Delay, Data to Output Y (Figures 1 and 3) 2.0 4.5 6.0 140 28 24 175 35 30 210 42 36 ns tPLH, tPHL Maximum Propagation Delay , Address to Output Y (Figures 1 and 3) 2.0 4.5 6.0 175 35 30 220 44 37 265 53 45 ns tPLZ, tPHZ Maximum Propagation Delay ,Output Enable to Output Y (Figures 2 and 4) 2.0 4.5 6.0 150 30 26 190 38 33 225 45 38 ns tPZL, tPZH Maximum Propagation Delay ,Output Enable to Output Y (Figures 2 and 4) 2.0 4.5 6.0 100 20 17 125 25 21 150 30 26 ns tTLH, tTHL Maximum Output Transition Time, Any Output (Figures 1 and 3) 2.0 4.5 6.0 75 15 13 95 19 16 110 22 19 ns Maximum Input Capacitance - 10 10 10 pF Maximum Three-State Output Capacitance (Output in High-Impedance State) - 15 15 15 pF CIN COUT Power Dissipation Capacitance (Per Muliplexer) CPD Used to determine the no-load dynamic power consumption: PD=CPDVCC2f+ICCVCC Figure 1. Switching Waveforms Typical @25C,VCC=5.0 V 31 pF Figure 2. Switching Waveforms 319 IN74HC253 IN74HC253 Figure 3. Test Circuit Figure 4. Test Circuit EXPANDED LOGIC DIAGRAM 320