LMH0031VS/NOPB - Texas Instruments

LMH0031

www.ti.com

SNLS218A –JANUARY 2006–REVISED APRIL 2013

LMH0031 SMPTE 292M/259M Digital Video Deserializer / Descrambler with Video

and Ancillary Data FIFOs

Check for Samples: LMH0031

1FEATURES APPLICATIONS

2• SDTV/HDTV Serial Digital Video Standard • SDTV/HDTV Serial-to-Parallel Digital Video

Compliant Interfaces for:

• Supports 270 Mbps, 360 Mbps, 540 Mbps, – Video Editing Equipment

1.483 Gbps and 1.485 Gbps Serial Video Data – VTRs

Rates with Auto-Detection – Standards Converters

• LSB De-Dithering Option – Digital Video Routers and Switchers

• Uses Low-Cost 27MHz Crystal or Clock – Digital Video Processing and Editing

Oscillator Reference Equipment

• Fast VCO Lock Time: < 500 µs at 1.485 Gbps – Video Test Pattern Generators and Digital

• Built-in Self-Test (BIST) and Video Test Pattern Video Test Equipment

Generator (TPG) – Video Signal Generators

(1) Patent Applications Made or Pending DESCRIPTION

• Automatic EDH/CRC Word and Flag

Processing The LMH0031 SMPTE 292M / 259M Digital Video

Deserializer/Descrambler with Video and Ancillary

• Ancillary Data FIFO with Extensive Packet Data FIFOs is a monolithic integrated circuit that

Handling Options deserializes and decodes SMPTE 292M, 1.485Gbps

• Adjustable, 4-Deep Parallel Output Video Data (or 1.483Gbps) serial component video data, to 20-bit

FIFO parallel data with a synchronized parallel word-rate

clock. It also deserializes and decodes SMPTE 259M,

• Flexible Control and Configuration I/O Port 270Mbps, 360Mbps and SMPTE 344M (proposed)

• LVCMOS Compatible Control Inputs and Clock 540Mbps serial component video data, to 10-bit

and Data Outputs parallel data. Functions performed by the LMH0031

• LVDS and ECL-Compatible, Differential, Serial include: clock/data recovery from the serial data,

Inputs serial-to-parallel data conversion, SMPTE standard

data decoding, NRZI-to-NRZ conversion, parallel data

• 3.3V I/O Power Supply and 2.5V Logic Power clock generation, word framing, CRC and EDH data

Supply Operation checking and handling, Ancillary Data extraction and

• Low Power: Typically 850mW automatic video format determination. The parallel

• 64-Pin TQFP Package video output features a variable-depth FIFO which

can be adjusted to delay the output data up to 4

• Commercial Temperature Range 0°C to +70°C parallel data clock periods. Ancillary Data may be

selectively extracted from the parallel data through

the use of masking and control bits in the

configuration and control registers and stored in the

on-chip FIFO. Reverse LSB dithering is also

implemented.

1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2All trademarks are the property of their respective owners.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

LMH0030

SD/HD Encoder/ Serializer/

Cable Driver

LMH0034

Adaptive Cable

Equalizer

75: Coaxial Cable

1 PF

75:

SMPTE Video

Data Input

SMPTE 292M

or 259M

Serial Data

VDD

LMH0031

SD/HD Decoder/

Deserializer

Parallel Ancilliary

Data Input

SMPTE Video

Data Output

Parallel Ancilliary

Data Output

75:

1 PF

LMH0031

SNLS218A –JANUARY 2006–REVISED APRIL 2013

www.ti.com

DESCRIPTION (CONTINUED)

The unique multi-functional I/O port of the LMH0031 provides external access to functions and data stored in the

configuration and control registers. This feature allows the designer greater flexibility in tailoring the LMH0031 to

the desired application. The LMH0031 is auto-configured to a default operating condition at power-on or after a

reset command. Separate power pins for the PLL, deserializer and other functional circuits improve power supply

rejection and noise performance.

The LMH0031 has a unique Built-In Self-Test (BIST) and video Test Pattern Generator (TPG). The BIST enables

comprehensive testing of the device by the user. The BIST uses the TPG as input data and includes SD and HD

component video test patterns, reference black, PLL and EQ pathologicals and a 75% saturation, 8 vertical

colour bar pattern, for all implemented rasters. The colour bar pattern has optional transition coding at changes in

the chroma and luma bar data. The TPG data is output via the parallel data port.

The LMH0030, SMPTE 292M / 259M Digital Video Serializer with Ancillary Data FIFO and Integrated Cable

Driver, is the ideal complement to the LMH0031.

The LMH0031's internal circuitry is powered from +2.5 Volts and the I/O circuitry from a +3.3 Volt supply. Power

dissipation is typically 850mW. The device is packaged in a 64-pin TQFP.

TYPICAL APPLICATION

Product Folder Links: LMH0031

TRS &

FORMAT

DETECTOR

CONFIGURATION

& CONTROL

REGISTERS

SMPTE NRZI-NRZ CONVERTER

DESCRAMBLER/

DESERIALIZER

EDH / CRC

GENERATORS/CHECKERS

PLL/CLOCK SYSTEM

BIST & TPG

RESET

CONTROL

FRAMING

CONTROL

DV[9:0]

RESET

SDI

ANCILLIARY

DATA FIFO

MULTI-FUNCTION I/O PORT

DV[19:10]

AD[9:0]

ANC / CTRL

ACLK

RD / WR

I/O[7:0]

INT. RESET

SYSTEM

MASTER

CONTROLLER

MASTER BUS

DE-DITHERING

PCLK

VIDEO DATA

FIFO & OUTPUT

VCLK

PCLK

VIDEO DATA BUS

SDI

BIAS

RBB

RREF

INPUT DATA SAMPLERS

CLOCK/DATA RECOVERY

REFERENCE CLOCK/OSCILLATOR

XTALi/Ext

Clk

XTALo

PCLK

LMH0031

www.ti.com

SNLS218A –JANUARY 2006–REVISED APRIL 2013

Block Diagram

Product Folder Links: LMH0031

4443424140393837363534

1213141516

11 10 9 8 7 6 5 4 3 2 1

LMH0031

48474645

VDDD

AD0

AD1

AD2

AD3

AD4

AD5

AD6

AD7

AD8

AD9

ACLK

VSSD

IO5

IO6

IO7

VDDIO

VSSD

DV10

DV11

DV12

DV13

DV14

DV15

DV16

DV17

DV18

DV19

IO2

IO3

IO4

DV0

DV1

DV2

DV3

DV4

DV5

DV6

DV7

DV8

DV9

IO1

IO0

VSSIO

VDDIO

VDDPLL

RESET

RD/WR

SSPLL

ANC/CTRL

DDSI

DDD

SSIO

SSSI

SDI

XTALo

REF

XTALi/Ext Clk

VCLK

SDI

VSSD

VDDD

VSSIO

LMH0031

SNLS218A –JANUARY 2006–REVISED APRIL 2013

www.ti.com

Connection Diagram

Figure 1. 64-Pin TQFP

See Package Number PAG0064A

Product Folder Links: LMH0031

LMH0031

www.ti.com

SNLS218A –JANUARY 2006–REVISED APRIL 2013

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

Absolute Maximum Ratings(1)(2)

CMOS I/O Supply Voltage (VDDIO–VSSIO): 4.0V

SDI Supply Voltage (VDDSI–VSSSI): 4.0V

Digital Logic Supply Voltage (VDDD–VSSD): 3.0V

PLL Supply Voltage (VDDPLL–VSSPLL): 3.0V

CMOS Input Voltage (Vi): VSSIO −0.15V to VDDIO

+0.15V

CMOS Output Voltage (Vo): VSSIO −0.15V to VDDIO

+0.15V

CMOS Input Current (single input): Vi = VSSIO −0.15V: −5 mA

Vi = VDDIO +0.15V: +5 mA

CMOS Output Source/Sink Current:CMOS Output Source/Sink Current: ±6 mA±6 mA

IBB Output Current: +300 μA

IREF Output Current: +300 μA

SDI Input Voltage (Vi): VSSSI −0.15V to VDDSI

+0.15V

Package Thermal Resistance θJA @ 0 LFM Airflow 40.1°C/W

θJA @ 500 LFM Airflow 24.5°C/W

θJC 5.23°C/W

Storage Temp. Range: −65°C to +150°C

Junction Temperature: +150°C

Lead Temperature (Soldering 4 Sec): +260°C

ESD Rating (HBM): 6.0 kV

ESD Rating (MM): 400 V

(1) Absolute Maximum Ratings are those parameter values beyond which the life and operation of the device cannot be ensured. The

stating herein of these maximums shall not be construed to imply that the device can or should be operated at or beyond these values.

The table of “Electrical Characteristics” specifies acceptable device operating conditions.

(2) It is anticipated that this device will not be offered in a military qualified version. If Military/Aerospace specified devices are required,

please contact the Texas Instruments Sales Office / Distributors for availability and specifications.

Recommended Operating Conditions

Symbol Parameter Conditions Reference Min Typ Max Units

VDDIO CMOS I/O Supply Voltage VDDIO−VSSIO 3.150 3.300 3.450 V

VDDSD SDI Supply Voltage VDDSI−VSSSI

VDDD Digital Logic Supply Voltage VDDD–VSSD 2.375 2.500 2.625 V

VDDPLL PLL Supply Voltage VDDPLL–VSSPLL

Operating Free Air

TA0 +70 °C

Temperature

Product Folder Links: LMH0031

LMH0031

SNLS218A –JANUARY 2006–REVISED APRIL 2013

www.ti.com

Required Input Conditions(1)(2)

Symbol Parameter Conditions Reference Min Typ Max Units

VIN Input Voltage Range VSSIO VDDIO V

All LVCMOS

Inputs

tr, tfRise Time, Fall Time 10%–90% 1.0 1.5 3.0 ns

SMPTE 259M, Level C 270

SMPTE 259M, Level D 360

BRSDI Serial Input Data Rate SMPTE 344M SDI, SDI 540 MBPS

SMPTE 292M 1,483

SMPTE 292M 1,485

VSSSI VDDSI

VCM(SDI) Common Mode Voltage VIN = 125 mVP-P V

+1.0V −0.05V

VIN(SDI) SDI Serial Input Voltage, 125 800 880 mVP-P

Single-ended

VIN(SDI) SDI Serial Input Voltage, SDI, SDI 125 800 880 mVP-P

Differential 20%–80%, SMPTE 259M 0.4 1.0 1.5 ns

Data Rates

tr, tfRise Time, Fall Time 20%–80%, SMPTE 292M 270 ps

Data Rates

Ancillary / Control Data Clock

fACLK VCLK MHz

Frequency

DCACLK Duty Cycle, Ancillary Clock ACLK 45 50 55 %

Ancillary / Control Clock and

tr, tf10%–90% 1.0 1.5 3.0 ns

Data Rise Time, Fall Time

Setup Time, ADNto ACLK or

tS3.0 1.5 ns

IONto ACLK Rising Edge Control Data Input or ION, ADN, ACLK

I/O Bus Input Timing Diagram

Hold Time, Rising Edge ACLK

tH3.0 1.5 ns

to ADNor ACLK to ION

Bias Supply Reference

RREF Tolerance 1% 4.75k Ω

Resistor

fEXT CLK External Clock Frequency Ext Clk −100 +100

27.0 MHz

ppm ppm

fXTAL Crystal Frequency See Figure 7 XTALo, XTALi

(1) Required Input Conditions are the electrical signal conditions or component values which shall be supplied by the circuit in which this

device is used in order for it to produce the specified DC and AC electrical output characteristics.

(2) Functional and certain other parametric tests utilize a LMH0030 as the input source to the SDI inputs of the LMH0031. The LMH0030 is

DC coupled to the inputs of the LMH0031. Typical VIN = 800 mV, VCM = 2.9 V.

Product Folder Links: LMH0031

LMH0031

www.ti.com

SNLS218A –JANUARY 2006–REVISED APRIL 2013

DC Electrical Characteristics

Over Supply Voltage and Operating Temperature ranges, unless otherwise specified(1)(2).

Symbol Parameter Conditions Reference Min Typ Max Units

VIH Input Voltage High Level 2.0 VDDIO V

VIL Input Voltage Low Level VSSIO 0.8

All LVCMOS

Inputs

IIH Input Current High Level VIH = VDDIO(3) +85 +150 µA

IIL Input Current Low Level VIL = VSSIO −1−20

VOH Output Voltage High Level IOH =−2 mA 2.4 2.7 VDDIO

VSSIO VSSIO

VOL Output Voltage Low Level IOL = +2 mA VSSIO +0.3 +0.5V

All LVCMOS V

VDDIO

Outputs

VOHV Minimum Dynamic VOH IOH =−2 mA (4) −0.5

VSSIO

VOLP Maximum Dynamic VOL IOL = +2 mA (4) +0.4

VSDI Serial Data Input Voltage 125 800 880 mVP-P

ISDI Serial Data Input Current SDI, SDI ±1 ±10 µA

VTH Input Thereshold Over VCM range <100 mV

IBB Bias Supply Output Current RBB = 8.66kΩ1% −220 −188 µA

IREF Reference Output Current RREF = 4.75kΩ1% −290 −262

270MBPS Data Rate 38.0 45.0

Power Supply Current, 3.3V

IDD (3.3V) VDDIO, VDDSI mA

Supply, Total 1,485MBPS Data Rate 47.0 50.0

270MBPS Data Rate 80 120

Power Supply Current, 2.5V

IDD (2.5V) VDDD, VDDPLL mA

Supply, Total 1,485MBPS Data Rate 220 340

(1) Current flow into device pins is defined as positive. Current flow out of device pins is defined as negative. All voltages are referenced to

VSSIO = VSSD = VSSSI = 0V.

(2) Typical values are stated for VDDIO = VDDSI = +3.3V, VDDD = VDDPLL = +2.5V and TA= +25°C.

(3) IIH includes static current required by input pull-down devices.

(4) VOHV and VOLP are measured with respect to reference ground. VOLP is the peak output LOW voltage or ground bounce that may occur

under dynamic simultaneous output switching conditions. VOHV is the lowest output HIGH voltage or output droop that may occur under

dynamic simultaneous output switching conditions.

Product Folder Links: LMH0031

LMH0031

SNLS218A –JANUARY 2006–REVISED APRIL 2013

www.ti.com

AC Electrical Characteristics

Over Supply Voltage and Operating Temperature ranges, unless otherwise specified(1).

Symbol Parameter Conditions Reference Min Typ Max Units

Serial Video Data Inputs

SMPTE 259M, Level C 270

SMPTE 259M, Level D 360

BRSDI Serial Input Data Rate SMPTE 344M 540 MBPS

SMPTE 292M 1,483

SDI, SDI

SMPTE 292M 1,485

20%–80%, SMPTE 259M 0.4 1.0 1.5 ns

Data Rates

tr, tfRise Time, Fall Time 20%–80%, SMPTE 292M 270 ps

Data Rates

Parallel Video Data Outputs

SMPTE 259M, 270MBPS 27.0

SMPTE 267M, 360MBPS 36.0

Video Output Clock

fVCLK SMPTE 344M, 540MBPS VCLK 54.0 MHz

Frequency SMPTE 292M, 1,483MBPS 74.176

SMPTE 292M, 1,485MBPS 74.25

Propagation Delay, Video VCLK to DVN

tpd 50%–50% 0.5 2.0 ns

Clock to Video Data Valid Timing Diagram

DCVDuty Cycle, Video Clock VCLK 50±5 %

27MHz 2.0

36MHz 1.4

Video Data Output Clock

tJIT VCLK nsP-P

Jitter 54MHz 1.0

74.25MHz 0.5

Parallel Ancillary / Control Data Inputs, Multi-function Parallel Bus Inputs

Ancillary / Control Data Clock

fACLK VCLK MHz

Frequency ACLK

Duty Cycle, Ancillary Data

DCAANC Data clock (2) 45 50 55 %

Clock

tr, tfOutput Rise Time, Fall Time 10%–90% 1.0 1.5 3.0

Setup Time, ADNto ACLK or

tSION, ADN, ACLK 3.0 1.5

IONto ACLK Rising Edge ns

Control Data Input or I/O Bus Timing Diagram

Input

Hold Time, Rising Edge ACLK

tH3.0 1.5

to ADNor ACLK to ION

Parallel Ancillary / Control Data Outputs

Propagation Delay, Clock to

tpd 8.5

Control Data ACLK to ADN

50%–50% ns

Timing Diagram

Propagation Delay, Clock to

tpd 11.5

Ancillary Data

Multi-function Parallel I/O Bus

IO0–IO7

tr, tfRise Time, Fall Time 10%–90% 1.0 1.5 3.0 ns

Timing Diagram

PLL/CDR, Format Detect

SD Rates(3) 0.32 1.0

tLOCK Lock Detect Time HD Rates(3) 0.26 1.0 ms

tFORMAT Format Detect Time All Rates 20

(1) Typical values are stated for VDDIO = VDDSI = +3.3V, VDDD = VDDPLL = +2.5V and TA= +25°C.

(2) When used to clock control data into or from the LMH0031, the duty cycle restriction does not apply.

(3) Measured from rising-edge of first SDI cycle until Lock Detect bit goes high (true). Lock time includes CDR phase acquisition time plus

PLL lock time.

Product Folder Links: LMH0031

Hi-Z test eqpt. t 5k:

(attenuation 0dB)

CMOS

outputs

VDDIO

IOL

IOH

CL including probe and jig

capacitance, 3pF max.

S1 - open, S2 - closed for VOH measurement

S1 - closed, S2 - open for VOL measurement

LMH0031

www.ti.com

SNLS218A –JANUARY 2006–REVISED APRIL 2013

Test Loads

Product Folder Links: LMH0031

1.0 PF

82.5:

+3.3 Vdc

+2.5 Vdc

0 Vdc

SDI

VDDSI

VDDIO

LMH0031

VSSIO

VSSD VDDD

RBB

SDI

VDDPLL

VSSSI

2.5V

Supply

3.3V

Supply

2.5V

Supply 3.3V

Supply

Output loads

omitted for clarity.

VSSPLL

12, 33,

20, 47,

6, 32,

DV0

DV1

DV2

DV3

DV4

DV5

DV6

DV7

DV8

DV9

VCLK

RESET

DV10

DV11

DV12

DV13

DV14

DV15

DV16

DV17

DV18

DV19

RD / WR

ANC / CTRL

HD Chroma,

SD Luma &

Chroma

HD Luma

4.7 PF

16V

0.1 PF

(x2)

4.7 PF

16V

0.1

(x4)

AD0

AD1

AD2

AD3

AD4

AD5

AD6

AD7

AD8

AD9

ACLK

IO1

IO0

IO2

IO3

IO4

IO5

IO6

IO7

XTALi/EXT CLK

XTALo

825:

8.66k

1 nF

SDI

26, 48

27 MHz

CLK. I/P

4.75k

RREF

Multi-

function

I/O Bus

Ancilliary/

Control Bus

LMH0031

SNLS218A –JANUARY 2006–REVISED APRIL 2013

www.ti.com

Test Circuit

Product Folder Links: LMH0031

VCLK

(ACLK)

AD[9:0]

INPUT DATA

50%

90%

10%

90%

10%

90%

10%

tr, tf

DV[19:0]

OUTPUT DATA

tPD

AD[9:0]

OUTPUT DATA

tPD

LMH0031

www.ti.com

SNLS218A –JANUARY 2006–REVISED APRIL 2013

Timing Diagram

Device Operation

INTRODUCTION

The LMH0031 SMPTE 292M/259M Digital Video Deserializer/Decoder is used in digital video signal origination

and destination equipment: cameras, video tape recorders, telecines, editors, standards converters, video test

and other equipment. It decodes and converts serial SDTV or HDTV component digital video signals into parallel

format. The LMH0031 decoder/deserializer processes serial digital video (SDV) signals conforming to SMPTE

259M, SMPTE 344M (proposed) or SMPTE 292M and operates at serial data rates of 270 Mbps, 360 Mbps, 540

Mbps, 1.483 Gbps and 1.485 Gbps. Corresponding parallel output data rates are 27.0 MHz, 36.0 MHz, 54.0

MHz, 74.176MHz and 74.25 MHz.

The LMH0031 accepts ECL or LVDS serial data input signals. Outputs signals are compatible with LVCMOS

logic devices.

NOTE

In the following explanations, these logical equivalences are observed: ON ≡Enabled ≡

Set ≡True ≡Logic_1 and OFF ≡Disabled ≡Reset ≡False ≡Logic_0.

VIDEO DATA PATH

The Serial Data Inputs (SDI) accept serial video data at SMPTE 259M standard definition, SMPTE 344M

(proposed) or SMPTE 292M high-definition data rates. These inputs accept standard ECL or LVDS signal levels

and may be used single-ended or differentially. Inputs may be DC or AC coupled, as required, to devices and

circuits supplying the data. Recommended operating conditions and all input DC and AC voltage and current

specifications shall be observed when designing the input coupling circuits.

For convenience, a reference bias source, pin name RREF, sets the reference current available from the input

bias source, pin name RBB. The recommended nominal value of RREF is 4.75kΩ, 1%. RBB is provided so that the

SDI inputs may be supplied DC bias voltage via external resistors when the inputs are AC-coupled. The bias

source should be loaded with a resistance to the VSS supply. The source current available at RBB is 200µA.

Figure 2 shows a typical input biasing scheme using RBB and RREF.

Product Folder Links: LMH0031

82.5:

1 PF

1 nF

4.75 k:

8.66 k:

SDI

RBB

RREF

SDI

LMH0031

825:

82.5:

1 PF

LMH0031

SNLS218A –JANUARY 2006–REVISED APRIL 2013

www.ti.com

Figure 2. Optional Input Biasing Scheme

The SMPTE descrambler receives NRZI serial data, converts it to NRZ, then decodes it to either 10-bit standard

definition or 20-bit high definition parallel video data using the reverse polynomial X9+ X4+ 1 as specified in the

respective standard: SMPTE 259M, SMPTE 344M (proposed) or SMPTE 292M. The data reception bit order is

LSB-first. All data processing is done at the parallel rate.

The LMH0031 incorporates circuitry that implements a method for handling data that has been subjected to LSB

dithering. When so enabled, data from the de-scrambler is routed for de-dithering. The De-Dither Enable bit in

the VIDEO INFO 0 control register enables this function. De-dithering of data present in the vertical blanking

interval can be selectively enabled by use of the V De-Dither Enable bit in the VIDEO INFO 0 control register.

The initial condition of De-Dither Enable and V De-Dither Enable is OFF.

The descrambler supplies signals to theTRS character detector which identifies the presence of the valid video

data. The TRS character detector processes the timing reference signals which control raster framing. TRS

(sync) characters are detected and the video is aligned on word boundaries. Data is re-synchronized with the

parallel word-rate clock. Interraction and operation of the character alignment control signals and indicators

Framing Mode,Framing Enable and NSP (New Sync Position) is described later in this datasheet.

The LMH0031 implements TRS character LSB-clipping as prescribed in ITU-R BT.601. LSB-clipping causes all

TRS characters with a value between 000h and 003h to be forced to 000h and all TRS characters with a value

between 3FCh and 3FFh to be forced to 3FFh. Clipping is done after descrambling and de-dithering.

Product Folder Links: LMH0031

LMH0031

www.ti.com

SNLS218A –JANUARY 2006–REVISED APRIL 2013

Once the PLL attains lock, the video format detector processes the received data to determine the raster

characteristics (video data format) and configure the LMH0031 to handle it. This assures that the parallel output

data will be properly formatted, that the correct data rate is selected and that Ancillary Data and CRC/EDH data

are correctly detected and checked. Supported parallel data formats or sub-formats may belong to any one of

several component standards: SMPTE 125M, SMPTE 267M, SMPTE 260M, 274M, 295M or 296M. Refer to

Table 4 for the supported formats. (See also the Application Information section for handling of other raster

formats or format extensions developed after this device was designed). The detected video standard information

is passed to the device control system and saved in the control registers from whence it may be read by the

user.

The LMH0031 may be configured to operate in a single video format by loading the appropriate FORMAT

SET[4:0] control data into the FORMAT 0 control register. Also, the LMH0031 may be configured to handle only

the standard-definition data formats by setting the SD ONLY bit or only the high-definition data formats by setting

the HD ONLY bit in the FORMAT 0 control register. When both bits are reset, the default condition, the part

automatically detects the data rate and range.

Aligned and de-processed parallel data passes into a variable-depth video FIFO prior to output. Video FIFO

depth from 0 to 4 registers is set by a 3-bit word written into the VIDEO FIFO Depth[2:0] bits in the ANC 0

control register. The video FIFO permits adjustment of the parallel video data output timing or delay at a parallel

word rate. The occurence of corresponding TRS indicator bits, EAV, SAV and NSP, in the control register

corresponds to the input register position of the FIFO. This positioning permits a look-ahead function in which the

alignment status of the video data can be determined up to four parallel clock periods prior to the appearance of

that data at the parallel data output.

The parallel video data is output on DV[19:0]. The 20-bit parallel video data is organized so that for HDTV data,

the upper-order 10 bits DV[19:10] are luminance (luma) information and the lower 10 bits DV[9:0] are colour

difference (chroma) information. SDTV data use the lower-order 10-bits DV[9:0] for both luma and chroma

information. (The SDTV parallel data is also duplicated on DV[19:10]). VCLK is the parallel output word rate clock

signal. The frequency of VCLK is appropriate to either the HD or SD data being processed. Data is valid between

the falling edges of a VCLK cycle. Data may be clocked into external devices on the rising-edge of VCLK. The

DV[19:0] and VCLK signals are LVCMOS-compatible.

ANCILLARY/CONTROL DATA PATH

The 10-bit ancillary and Control Data PortAD[9:0] serves two functions in the LMH0031. Ancillary Data from

the Ancillary Data FIFO is output from this port after its recovery from the video data stream. The utilization and

flow of Ancillary Data from the device is managed by a system of control bits, masks and IDs stored in the

control data registers. This port also provides read/write access to contents of the configuration and control

registers. The signals RD/WR,ANC/CTRL and ACLK control data flow through the port.

CONTROL DATA FUNCTIONS

Control data is input to and output from the LMH0031 using the lower-order 8 bits AD[7:0] of the

ancillary/Control Data Port. This control data initializes, monitors and controls operation of the LMH0031. The

upper two bits AD[9:8] of the port function as handshaking signals with the device accessing the port. When

either a control register read or write address is being written to the port, AD[9:8] must be driven as 00b (0XXh,

where XX are AD[7:0]). When control data is being written to the port, AD[9:8] must be driven as 11b (3XXh,

where XX are AD[7:0]). When control data is being read from the port, the LMH0031 will output AD[9:8] as 10b

(2XXh, where XX are output data AD[7:0]) and may be ignored by the monitoring system.

NOTE

After either a manual or power-on reset, ACLK must be toggled three (3) times to complete

initiallization of the Ancillary and Control Data Port.

The sequence of clock and control signals for reading control data from the ancillary/control data port is shown in

Figure 3.Control data read mode is invoked by making the ANC/CTRL input low and the RD/WR input high.

The 8-bit address of the control register set to be accessed is input to the port on bits AD[7:0]. To identify the

data as an address, AD[9:8] must be driven as 00b. The complete address word will be 0XXh, where 0 is

AD[9:8] and XX are AD[7:0]. The address is captured on the rising edge of ACLK. When control data is being

read from the port, the LMH0031 will output AD[9:8] as 10b (2XXh, where XX are output data AD[7:0]) and may

be ignored by the monitoring system. Data being output from the selected register is driven by the port

Product Folder Links: LMH0031

RD / WR

ANC / CTRL

ADDR DATA DATAADDR ADDR DATAAD[7:0]

WRITE

EXTERNAL BUS MUST

RELEASE

INTERNAL BUS WILL

RELEASE

ACLK

READ READ

AD[9:8]

AD[9]

AD[8]

DRIVEN REC'D DRIVEN REC'D DRIVEN DRIVEN

AD[9]

AD[8]AD[8]

AD[9]

AD[8]

AD[9:8]

LMH0031

SNLS218A –JANUARY 2006–REVISED APRIL 2013

www.ti.com

immediately following the rising edge of ACLK or when the address signal is removed. For optimum system

timing, the signals driving the address to the port should be removed immediately after the address is clocked

into the port and before or simultaneously with the falling edge of ACLK at the end of that address cycle. Output

data remains stable until the next rising edge of ACLK and may be written into external devices at any time after

the removal of the address signal. This second clock resets the port from drive to receive and readies the port for

another access cycle.

Example: Read the Full-field Flags via the AD port.

1. Set ANC/CTRL to a logic-low.

2. Set RD/WR to a logic-high.

3. Present 001h to AD[9:0] as the register address.

4. Toggle ACLK.

5. Release the bus driving the AD port.

6. Read the data present on the AD port. The Full-field Flags are bits AD[4:0].

7. Toggle ACLK to release the AD port.

Figure 4 shows the sequence of clock and control signals for writing control data to the ancillary/control data port.

The control data write mode is similar to the read mode. Control data write mode is invoked by making the

ANC/CTRL input low and the RD/WR input low. The 8-bit address of the control register set to be accessed is

input to the port on bits AD[7:0]. When a control register write address is being written to the port, AD[9:8] must

be driven as 00b (0XXh, where XX are AD[7:0]). The address is captured on the rising edge of ACLK. The

address data is removed on the falling edge of ACLK. Next, the control data is presented to the port bits AD[7:0]

and written into the selected register on the next rising edge of ACLK. When control data is being written to the

port, AD[9:8] must be driven as 11b (3XXh, where XX are AD[7:0]). Control data written into the registers may

be read out non-destructively in most cases.

Example: Setup (without enabling) the TPG Mode via the AD port using the 1125 line, 30 frame, 74.25MHz,

interlaced component (SMPTE 274M) colour bars as test pattern. The TPG may be enabled after setup using the

Multi-function I/O port or by the control registers.

1. Set ANC/CTRL to a logic-low.

2. Set RD/WR to a logic-low.

3. Present 00Dh to AD[9:0] as the Test 0 register address.

4. Toggle ACLK.

5. Present 327h to AD[9:0] as the register data.

6. Toggle ACLK.

Figure 3. Control Data Read Timing (2 read and 1 write cycle shown)

Product Folder Links: LMH0031

LMH0031

www.ti.com

SNLS218A –JANUARY 2006–REVISED APRIL 2013

Figure 4. Control Data Write Timing

Ancillary Data Functions

The LMH0031 can recover Ancillary Data from the serial data stream. This Ancillary Data and related control

characters are defined in the relevant SMPTE standards and may reside in the horizontal and vertical blanking

intervals. The data can consist of different types of message packets including audio data. The serial Ancillary

Data space must be formatted according to SMPTE 291M. The LMH0031 supports Ancillary Data in the

chrominance channel (C’r/C’b) only for high-definition operation. Ancillary Data for standard definition

follows the requirements of SMPTE 125M.

The Ancillary Data FIFO is sized to handle a maximum length ANC data Type 1 or Type 2 packet without the

ANC Flag, 259 words. Defined in SMPTE 291M, the packet consists of the Ancillary Data Flag, a 3-word Data ID

and Data Count, 255 8- or 10-bit User Data Words and a Checksum. The design of the LMH0031 Ancillary Data

FIFO also allows storage of up to 8 shorter length messages with total length not exceeding 259 words including

all ID information. Ancillary Data is copied from the data stream into the Ancillary Data FIFO. The parallel

Ancillary Data will still be present in the parallel chroma output DV[9:0]. ancillary flag information is not extracted

into the FIFO.

Copying of ANC data from the video data into the FIFO is controlled by the ANC Mask and ANC ID bits in the

control registers. A system of flags, ANC FIFO Empty,ANC FIFO 90% Full,ANC FIFO Full and ANC FIFO

Overrun are used to monitor FIFO status. The details and functions of these and other control words are

explained later in this datasheet.

Figure 5 shows the relationship of clock, data and control signals for reading Ancillary Data from the port

AD[9:0]. In Ancillary Data read mode, 10-bit Ancillary Data is routed from the Ancillary Data FIFO and read

from the port AD[9:0] at a rate determined by ACLK.

Ancillary Data read (output) mode is invoked by making the ANC/CTRL input high and the RD/WR input high.

Ancillary Data is clocked from the FIFO on the L-H transition of ACLK. Data may be read from the port on rising

edges of ACLK, after the specified propagation delay, until the FIFO is emptied. Data may only be read from the

port when in the Ancillary Data mode. Ancillary Data cannot be written to the port.

To conserve power when the Ancillary Data function is not being used, the internal Ancillary Data FIFO clock is

disabled. This clock must be enabled before Ancillary Data may be replicated into the FIFO for output. This

internal FIFO clock is controlled by FIFO CLOCK ENABLE, bit-6 of the ANC 5 register (address 17h). The

default condition of FIFO CLOCK ENABLE is OFF. After enabling the internal FIFO clock by turning this bit ON,

ACLK must be toggled three (3) times to propagate the enable to the clock tree.

Product Folder Links: LMH0031

ACLK

MULTIFUNCTION

I/O PORT BIT

ACLK

RD/WR

ANC/CTRL

AD[9:0]

READ

DATA DATA DATADATADATA DATA DATA

LMH0031

SNLS218A –JANUARY 2006–REVISED APRIL 2013

www.ti.com

Figure 5. Ancillary Data Read Timing

MULTI-FUNCTION I/O PORT

The multi-function I/O port can be configured to provide immediate access to many control and indicator

functions that are stored within the LMH0031’s configuration and control registers. The individual pins comprising

this port are assigned as input or output for selected functions stored in the control data registers.

The multi-function I/O port is configured by way of an 8x6-bit register bank consisting of registers I/O pin 0

CONFIG through I/O pin 7 CONFIG. The contents of these registers determine whether the port bits function as

inputs or outputs and to which control function or indicator each port bit is assigned. Port bits may be assigned to

access different functions and indicators or any or all port bits may be assigned to access the same function or

indicator (output mode only). The same indicator or function should not be assigned to more than one port bit as

an input. Controls and indicators that are accessible by the port and their corresponding selection addresses are

given in the I/O Pin Configuration Register Addresses, Table 6.Table 2 gives the control register bit

assignments.

Data resulting from device operation will be sent to the selected I/O port bit. This same data is also stored in the

configuration and control registers. Mapping the control and indicator functions in this manner means that device

operation will be immediately reflected at the I/O port pins thereby ensuring more reliable real-time operation of

the device within and by the host system.

When a multifunction I/O port bit is used as input to a control register bit, data must be presented to the I/O port

bit and clocked into the register bit using ACLK as shown in Figure 6. Port timing for bit write operations is the

same as for the ANC/CTRL port operation.

Figure 6. I/O Port Data Write Timing

Example: Program multi-function I/O port bit-0 as the CRC Luma Error bit output.

1. Set ANC/CTRL to a logic-low.

2. Set RD/WR to a logic-low.

3. Present 00Fh to AD[9:0] as the I/O PIN 0 CONFIG register address.

4. Toggle ACLK.

5. Present 310h to AD[9:0] as the register data.

6. Toggle ACLK.

Product Folder Links: LMH0031

27MHz

33pF 33pF

pin 60 pin 61

LMH0031

www.ti.com

SNLS218A –JANUARY 2006–REVISED APRIL 2013

EDH/CRC SYSTEM

The LMH0031 has EDH and CRC character generation and checking circuitry. The EDH system functions as

described in SMPTE Recommended Practice RP-165. The CRC system functions as specified in SMPTE 292M.

The EDH/CRC polynomial generators/checkers accept parallel data from the de-serializing system and

generate the EDH and CRC check words for comparison with those received in the data.

The EDH Enable bit in the control register enables the EDH generation and checking system. Incoming SDTV

data is checked for errors and the EDH flags are updated automatically. EDH errors are reported in the EDH0,

EDH1, and EDH2 register sets of the configuration and control registers.

Updated or new EDH check words and flags may be generated and inserted in the data. EDH check words are

generated using the polynomial X16 + X12 + X6+ 1 per SMPTE RP165. Generation and automatic insertion of

new or corrected EDH check words is controlled by EDH Force and EDH Enable bits in the control registers.

EDH check words and status flags are inserted in the parallel data at the correct positions in the Ancillary Data

space and formatted per SMPTE 291M. After a reset, the initial state of all EDH and CRC check characters is

00h.

The SMPTE 292M high definition video standard employs CRC (cyclic redundancy check codes) error checking

instead of EDH. The CRC consists of two 18-bit words generated using the polynomial X18 + X5+ X4+ 1 per

SMPTE 292M. One CRC is used for luminance and one for chrominance data. The CRCs appear in the data

stream following the EAV and line number characters. The CRCs are checked and errors are reported in the

EDH0, EDH1, and EDH2 register sets of the configuration and control registers.

PHASE-LOCKED LOOP / CLOCK-DATA RECOVERY SYSTEM

The phase-locked loop and clock-data recovery (PLL/CDR) system generates all internal timing and data rate

clocks for the LMH0031. The PLL/CDR system consists of five main functional blocks: 1) the input buffer which

receives the incoming data, 2) input data samplers which oversample the data coming from the input buffer, 3) a

PLL (VCO, divider chain, phase-frequency detector and internal loop filter) which generates sampling and other

system clocks, 4) a digital CDR system to recover the oversampled serial input data from the samplers and the

digital system control and 5) a rate detect controller which sequences the PLL to find the data rate.

Using an oversampling technique, the timing information encoded in the serial data is extracted and used to

synchronize the recovered clock and data. The parallel data rate and other clock signals are derived from the

regenerated serial clock. The parallel data rate clock is 1/10th of the serial data rate clock for standard definition

or 1/20th of the serial data clock frequency for high definition. The data interface between the CDR and the

digital processing block uses 10-bit data plus the required clocks.

The PLL is held in coarse frequency lock by an external 27MHz clock signal, EXT CLK, or by an external 27MHz

crystal and internal oscillator. Upon power-on, EXT CLK is the default reference. The internal oscillator and an

external crystal may be used as the reference by setting the OSCEN bit in the CDR register. The reference

clock reduces lock latency and enhances format and auto-rate detection robustness. PLL acquisition, data phase

alignment and format detection time is 20ms or less at 1.485Mbps. The VCO has separate VDDPLL and VSSPLL

power supply feeds, pins 51 and 52, which may be supplied power via an external low-pass filter, if desired.

Figure 7. Crystal and Load Circuit

A 27MHz crystal and load circuit may be used to provide the reference clock. A fundamental mode crystal with

the following parameters is used: frequency 27MHz, frequency tolerance ±30ppm, load capacitance 18pF,

maximum drive level 100µW, equivalent series resistance <50Ω, operating temperature range 0°C to 70°C. Refer

to Figure 7 for a typical load circuit and connection information.

Product Folder Links: LMH0031

LMH0031

SNLS218A –JANUARY 2006–REVISED APRIL 2013

www.ti.com

The LMH0031 indicates that the PLL is locked to the incoming data rate and that the CDR has acquired a phase

of the serial data by setting the Lock Detect bit in the Video Info 0 control register. Indication of the standard

being processed is retained in the FORMAT[4:0] bits in the FORMAT 1 control data register. Format data from

this register can be programmed for output on the multi-function I/O port. The power-on default assigns Lock

Detect as I/O Port bit 4.

POWER SUPPLIES, POWER-ON-RESET AND RESET INPUT

The LMH0031 requires two power supplies, 2.5V for the core logic functions and 3.3V for the I/O functions. The

supplies must be applied to the device in proper sequence. The 3.3V supply must be applied prior to or

coincident with the 2.5V supply. Application of the 2.5V supply must not precede the 3.3V supply. It is

recommended that the 3.3V supply be configured or designed so as to control application of the 2.5V supply in

order to satisfy this sequencing requirement.

The LMH0031 has an automatic, power-on-reset circuit. Reset initializes the device and clears TRS detection

circuitry, all latches, registers, counters and polynomial generators/checkers and resets the EDH/CRC characters

to 00h. An active-HIGH-true, manual reset input is available at pin 49. The reset input has an internal pull-down

device and may be considered inactive when unconnected.

Important: When power is first applied to the device or following a reset, the ancillary and Control Data Port

must be initialized to receive data. This is done by toggling ACLK three times.

TEST PATTERN GENERATOR (TPG) AND BUILT-IN SELF-TEST (BIST)

The LMH0031 includes an on-board, parallel video test pattern generator (TPG). Four test pattern types are

available in both HD and SD formats, NTSC and PAL standards, and 4x3 and 16x9 raster sizes. The test

patterns are: flat-field black, PLL pathological, equalizer (EQ) pathological and a 75%, 8-colour vertical bar

pattern. The pathologicals follow recommendations contained in SMPTE RP 178-1996 regarding the test data

used. The colour bar pattern has optional bandwidth limiting coding in the chroma and luma data transitions

between bars. The VPG FILTER ENABLE bit in the VIDEO INFO 0 control register enables the colour bar filter

function. The test pattern data is available at the video data outputs, DV[19:0] with a corresponding parallel rate

clock, VCLK, appropriate to the particular standard and format selected.

The TPG also functions as a built-in self-test (BIST) which can be used to verify device functionality. The BIST

function performs a comprehensive go/no-go test of the device. The test may be run using any of the HD colour

bar patterns or one of two SD patterns, either the 270 Mb/s NTSC colour bar or the PAL PLL pathological, as the

test data pattern. Data is input from the digital processing block, processed through the device and tested for

errors using either the EDH system for SD or the CRC system for HD. Clock signals from the CDR block supply

timing for the test data. The CDR must be supplied a 27MHz reference clock via the XTALi/Ext Clk input (or

using the internal oscillator and crystal) during the TPG or BIST function. A go/no-go indication is logged in the

Pass/Fail bit of the TEST 0 control register set. This bit may be assigned as an output on the multifunction I/O

port.

TPG and BIST operation is initiated by loading the code for the desired test pattern into the Test Pattern

Select[5:0] bits and by setting the TPG Enable bit of the TEST 0 register. Note that when attempting to use the

TPG or BIST immediately after the device has been reset or powered on, the TPG defaults to the 270Mbps SD

rate. The device must be configured for the desired test pattern by loading the appropriate code in to the TEST 0

configure itself to run at the correct rate and generate valid data. Table 5 gives the available test patterns and

codes.

The Pass/Fail bit in the control register gives the device test status indication. If no errors have been detected,

this bit will be set to logic-1 approximately 2 field intervals after TPG Enable is set. If errors have been detected

in the internal circuitry of the LMH0031, Pass/Fail will remain reset to a logic-0. TPG or BIST operation is

stopped by resetting the TPG Enable bit. Parallel output data is present at the DV[19:0] outputs during TPG or

BIST operation.

Example: Enable the TPG Mode to use the NTSC 270Mbps colour bars as the BIST and TPG pattern. Enable

TPG operation using the I/O port.

1. Set ANC/CTRL to a logic-low.

2. Set RD/WR to a logic-low.

3. Present 00Dh to AD[9:0] as the TEST 0 register address.

Product Folder Links: LMH0031

LMH0031

www.ti.com

SNLS218A –JANUARY 2006–REVISED APRIL 2013

4. Toggle ACLK.

5. Present 343h to AD[9:0] as the register data (525 line, 30 frame, 27MHz, NTSC 4x3, colour bars (SMPTE

125M)).

6. Toggle ACLK.

7. The PASS/FAIL indicator, TEST 0 register, Bit 7, should be read for the result of the test. Alternatively, this

bit may be mapped to a convenient bit of the Multi-function I/O bus. The test pattern data and clock is

available at the DV[19:0] and VCLK outputs.

CONFIGURATION AND CONTROL REGISTERS

The configuration and control registers store data which determines the operational modes of the LMH0031 or

which result from its operation. Many of these registers may be assigned as external I/O functions which are then

available on the multi-function I/O bus. These functions are summarized in Table 1 and detailed in Table 2. The

power-on default condition for the multi-function I/O port is indicated in Table 1 and detailed in Table 6.

Table 1. Configuration and Control Data Register Summary(1)

Available on

I/O Bus

EDH and CRC Operations

CRC Error (SD/HD) 1 R Reset Output See (2) I/O 5

CRC Error Luma 1 R Reset Output

CRC Error Chroma 1 R Reset Output

CRC Replace 1 R/W OFF No See (3)

Full-Field Flags 5 R Reset No

Active Picture Flags 5 R Reset No

ANC Flags 5 R Reset No

EDH Force 1 R/W OFF Input

EDH Enable 1 R/W ON Input

F/F Flag Error 1 R Reset Output

A/P Flag Error 1 R Reset Output

ANC Flag Error 1 R Reset Output

Ancillary Data Operations

ANC Checksum Force 1 R/W OFF Input

ANC Checksum Error 1 R Reset Output

ANC FIFO Empty 1 R Set Output See (2) I/O 6

ANC FIFO 90% Full 1 R Reset Output

ANC FIFO Full 1 R Reset Output

ANC FIFO Overrun 1 R Reset Output

ANC ID 16 R/W 0000h No

ANC Mask 16 R/W FFFFh No

MSG Track 1 R/W OFF No

MSG Flush Static 1 R/W OFF No

FIFO Flush Static 1 R/W OFF No

Full MSG Available 1 R OFF Output

Short MSG Detect 1 R OFF Output

FIFO Clock Enable 1 R/W OFF No

FIFO Extract Enable 1 R/W OFF Input

Video FIFO Operation

Video FIFO Depth 3 R/W 000b No

(1) ON = SET = logic-1, OFF = RESET = logic-0 (positive logic).

(2) Connected to multifunction I/O port at power-on.

(3) Special or restricted functionality. Refer to text for details.

Product Folder Links: LMH0031

LMH0031

SNLS218A –JANUARY 2006–REVISED APRIL 2013

www.ti.com

Table 1. Configuration and Control Data Register Summary(1) (continued)

Available on

I/O Bus

Video Format Operations

Format Set 5 R/W 00000B No

SD Only 1 R/W OFF No

HD Only 1 R/W OFF No

Format 5 R Output Format [4] (2) I/O 3

H 1 R Output See (2) I/O 2

V 1 R Output See (2) I/O 1

F 1 R Output See (2) I/O 0

Framing Mode 1 R/W ON No

Framing Enable 1 R/W ON Input

New Sync Position (NSP) 1 R Output

SAV 1 R Output

EAV 1 R Output See (2) I/O 7

De-scramble Enable 1 R/W ON No

NRZI Enable 1 R/W ON No

LSB Clipping Enable 1 R/W ON No

Sync Detect Enable 1 R/W ON No

De-Dither Enable 1 R/W OFF Input

Vert. De-Dither Enable 1 R/W OFF Input

Lock Detect 1 R Output See (4) I/O 4

Unscrambled 1 R/W OFF No See (5)

Video Data Out

TPG and BIST Operations

Test Pattern Select 6 R/W 000000b Input 525/27 MHz/Black

TPG Enable 1 R/W OFF Input

Pass/Fail 1 R Output

VPG Filter Enable 1 R/W OFF Input

Reference Clock Operations

Reference Clock 2 R/W 00b No EXT CLK Enabled

External Vclk 1 R/W OFF No See (5)

Multifunction I/O Bus Operations

I/O Bus Pin Config. 48 R/W See Table 6 No

(4) Connected to multifunction I/O port at power-on.

(5) Special or restricted functionality. Refer to text for details.

Table 2. Control Register Bit Assignments

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

EDH 0 (register address 01h)

CRC ERROR EDH FORCE EDH ENABLE F/F UES F/F IDA F/F IDH F/F EDA F/F EDH

EDH 1 (register address 02h)

CRC CRC ERROR CRC ERROR A/P UES A/P IDA A/P IDH A/P EDA A/P EDH

REPLACE LUMA CHROMA

EDH 2 (register address 03h)

F/F FLAG A/P FLAG ANC FLAG ANC UES ANC IDA ANC IDH ANC EDA ANC EDH

ERROR ERROR ERROR

ANC 0 (register address 04h)

VIDEO VIDEO VIDEO ANC FIFO ANC FIFO ANC FIFO ANC CHECK- ANC CHECK-

FIFO-DEPTH(2) FIFO-DEPTH(1) FIFO-DEPTH(0) OVERRUN EMPTY FULL SUM ERROR SUM FORCE

Product Folder Links: LMH0031

LMH0031

www.ti.com

SNLS218A –JANUARY 2006–REVISED APRIL 2013

Table 2. Control Register Bit Assignments (continued)

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

ANC 1 (register address 05h)

ANC ID(7) ANC ID(6) ANC ID(5) ANC ID(4) ANC ID(3) ANC ID(2) ANC ID(1) ANC ID(0)

ANC 2 (register address 06h)

ANC ID(15) ANC ID(14) ANC ID(13) ANC ID(12) ANC ID(11) ANC ID(10) ANC ID(9) ANC ID(8)

ANC 3 (register address 07h)

ANC MASK(7) ANC MASK(6) ANC MASK(5) ANC MASK(4) ANC MASK(3) ANC MASK(2) ANC MASK(1) ANC MASK(0)

ANC 4 (register address 08h)

ANC ANC ANC

ANC MASK(15) ANC MASK(14) ANC MASK(13) ANC MASK(9) ANC MASK(8)

MASK(12) MASK(11) MASK(10)

ANC 5 (register address 17h)

FIFO EXTRACT FIFO CLOCK FULL MSG FIFO FLUSH MSG FLUSH

reserved reserved MSG TRACK

ENABLE ENABLE AVAILABLE STATIC STATIC

ANC 6 (register address 18h)

ANC FIFO SHORT MSG ANC PARITY reserved reserved reserved reserved VANC

90% FULL DETECT MASK

FORMAT 0 (register address 0Bh)

FRAMING FORMAT FORMAT FORMAT FORMAT FORMAT

SD ONLY HD ONLY

MODE SET(4) SET(3) SET(2) SET(1) SET(0)

FORMAT 1 (register address 0Ch)

F V H FORMAT(4) FORMAT(3) FORMAT(2) FORMAT(1) FORMAT(0)

TEST 0 (register address 0Dh)

TEST TEST TEST TEST TEST

TEST PATTERN

PASS/FAIL TPG ENABLE PATTERN PATTERN PATTERN PATTERN PATTERN

SELECT(5) SELECT(4) SELECT(3) SELECT(2) SELECT(1) SELECT(0)

VIDEO INFO 0 (register address 0Eh)

VERT. DE-

DE-DITHER VPG FILTER LOCK FRAMING

DITHER EAV SAV NSP

ENABLE ENABLE DETECT ENABLE

ENABLE

VIDEO CONTROL 0 (register address 55h)

EXTERNAL SYNC DETECT LSB CLIP DE-Scramble

reserved reserved NRZI ENABLE reserved

VCLK ENABLE ENABLE ENABLE

REFERENCE CLOCK (register address 67h)

reserved reserved reserved reserved reserved INT_OSC EN CLK EN reserved

MULTI-FUNCTION I/O BUS PIN CONFIGURATION

I/O PIN 0 CONFIG (register address 0Fh)

reserved reserved PIN 0 SEL[5] PIN 0 SEL[4] PIN 0 SEL[3] PIN 0 SEL[2] PIN 0 SEL[1] PIN 0 SEL[0]

I/O PIN 1 CONFIG (register address 10h)

reserved reserved PIN 1 SEL[5] PIN 1 SEL[4] PIN 1 SEL[3] PIN 1 SEL[2] PIN 1 SEL[1] PIN 1 SEL[0]

I/O PIN 2 CONFIG (register address 11h)

reserved reserved PIN 2 SEL[5] PIN 2 SEL[4] PIN 2 SEL[3] PIN 2 SEL[2] PIN 2 SEL[1] PIN 2 SEL[0]

I/O PIN 3 CONFIG (register address 12h)

reserved reserved PIN 3 SEL[5] PIN 3 SEL[4] PIN 3 SEL[3] PIN 3 SEL[2] PIN 3 SEL[1] PIN 3 SEL[0]

I/O PIN 4 CONFIG (register address 13h)

reserved reserved PIN 4 SEL[5] PIN 4 SEL[4] PIN 4 SEL[3] PIN 4 SEL[2] PIN 4 SEL[1] PIN 4 SEL[0]

I/P PIN 5 CONFIG (register address 14h)

reserved reserved PIN 5 SEL[5] PIN 5 SEL[4] PIN 5 SEL[3] PIN 5 SEL[2] PIN 5 SEL[1] PIN 5 SEL[0]

I/O PIN 6 CONFIG (register address 15h)

reserved reserved PIN 6 SEL[5] PIN 6 SEL[4] PIN 6 SEL[3] PIN 6 SEL[2] PIN 6 SEL[1] PIN 6 SEL[0]

I/O PIN 7 CONFIG (register address 16h)

reserved reserved PIN 7 SEL[5] PIN 7 SEL[4] PIN 7 SEL[3] PIN 7 SEL[2] PIN 7 SEL[1] PIN 7 SEL[0]

Product Folder Links: LMH0031

LMH0031

SNLS218A –JANUARY 2006–REVISED APRIL 2013

www.ti.com

Table 3. Control Register Addresses

Address

EDH 0 01

EDH 1 02

EDH 2 03

ANC 0 04

ANC 1 05

ANC 2 06

ANC 3 07

ANC 4 08

ANC 5 17

ANC 6 18

FORMAT 0 0B

FORMAT 1 0C

TEST 0 0D

VIDEO INFO 0 0E

I/O PIN 0 CONFIG 0F

I/O PIN 1 CONFIG 10

I/O PIN 2 CONFIG 11

I/O PIN 3 CONFIG 12

I/O PIN 4 CONFIG 13

I/O PIN 5 CONFIG 14

I/O PIN 6 CONFIG 15

I/O PIN 7 CONFIG 16

VIDEO CONTROL 0 55

VIDEO CONTROL 1 56

REFERENCE CLOCK 67

EDH 0 (register 01h)

The EDH Full-Field flags F/F UES,F/F IDA,F/F IDH,F/F EDA andF/F EDH are defined in SMPTE RP 165. The

flags are updated automatically when the EDH function is enabled and data is being received.

The EDH ENABLE bit, when set, enables operation of the EDH generator function during SD operation. The

default condition of this bit is set (ON).

The EDH FORCE bit, when set, causes updated EDH packets to be inserted in the parallel output data

regardless of the previous condition of EDH checkwords and flags in the input serial data. This function may be

used in situations where video content has been edited thus making the previous EDH information invalid. The

default condition of this bit is reset (OFF).

The CRC ERROR bit indicates that errors in either the EDH checksums (SD) or CRC checkwords (HD) were

detected in the serial input data. This bit is a combined function which indicates the presence of either EDH

errors during SD operation or CRC errors during HD operation.

EDH 1 (register 02h)

The EDH Active Picture flags A/P UES,A/P IDA,A/P IDH,A/P EDA andA/P EDH are defined in SMPTE RP

165. The flags are updated automatically when the EDH function is enabled and data is being received.

Specific types of CRC errors in incoming HD serial data are reported in the CRC ERROR LUMA and CRC

ERROR CHROMA bits.

The CRC REPLACE bit, when set, causes the CRCs in the incoming data to be replaced with CRCs calculated

by the LMH0031. The bit is normally reset (OFF).

Product Folder Links: LMH0031

LMH0031

www.ti.com

SNLS218A –JANUARY 2006–REVISED APRIL 2013

EDH 2 (register 03h)

The EDH Ancillary Data flags ANC UES,ANC IDA,ANC IDH,ANC EDA andANC EDH are defined in SMPTE

RP 165. The flags are updated automatically when the EDH function is enabled and data is being received.

The status of EDH flag errors in incoming SD serial data are reported in the ffFlagError,apFlagError and

ancFlagError bits. Each of these bits is the logical-OR of the corresponding EDH and EDA flags.

ANC 0 (Address 04h)

The V FIFO Depth[2:0] bits control the depth of the video FIFO which preceeds the parallel output data drivers.

The depth can be set from 0 to 4 stages by writing the corresponding binary code into these bits. For example: to

set the Video FIFO depth at two registers, load 11010XXXXXb into the ANC 0 control register (where X

represents the other functional bits of this register).

NOTE

When changing some but not all bits in a register and to retain unchanged other data

previously stored in the register, read the register’s contents and logically-OR this with the

new data. Then write the modified data back into the register.

Flags for ANC FIFO EMPTY,ANC FIFO 90% FULL,ANC FIFO FULL and ANC FIFO OVERRUN are available

in the configuration and control register set. These flags can also be assigned as outputs on the multi-function

I/O port. ANC FIFO EMPTY when set indicates that the FIFO contains no data. ANC FIFO 90% FULL indicates

when the FIFO is at 90% of capacity. Since it is virtually impossible for the host processor to begin extracting

data from the FIFO after it has been flagged as full without the possibility of an overrun condition occurring, ANC

FIFO 90% FULL is used as an advanced command to the host to begin extracting data from the FIFO. To be

used properly, ANC FIFO 90% FULL should be assigned as an output on the multi-function I/O port and

monitored by the host system. Otherwise, inadvertent loss of ancillary packet data could occur. ANC FIFO FULL

when set indicates that the FIFO registers are completely filled with data.

The ANC FIFO OVERRUN flag indicates that an attempt to write data into a full FIFO has occurred. ANC FIFO

OVERRUN can be reset by reading the bit's status via the ancillary/Control port. If an overrun occurrs, the status

of the FIFO message tracking will be invalidated. In this event, the FIFO should be flushed to reset the message

tracking pointers. Any messages then in the FIFO will be lost.

The ANC Checksum Force bit, under certain conditions, enables the overwriting of Ancillary Data checksums

received in the data. Calculation and insertion of new Ancillary Data checksums is controlled by the ANC

Checksum Force bit. If a checksum error is detected (calculated and received checksums do not match) and the

ANC Checksum Force bit is set, the ANC Checksum Error bit is set and a new checksum is inserted in the

Ancillary Data replacing the previous one. If a checksum error is detected and the ANC Checksum Force bit is

not set, the checksum mismatch is reported via the ANC Checksum Error bit. ANC Checksum Error is

available as an output on the multifunction I/O port.

ANC 1 AND 2 (Addresses 05h and 06h)

The extraction of Ancillary Data packets from video data into the FIFO is controlled by the ANC MASK[15:0] and

ANC ID[15:0] bits in the control registers. The ANC ID[7:0] register normally is set to a valid 8-bit code used for

component Ancillary Data packet DID identification as specified in SMPTE 291M-1998. Similarly, ANC ID[15:8]

normally is set to a valid 8-bit code used for component Ancillary Data packet SDID/DBN identification.

ANC 3 AND 4 (Addresses 07h and 08h)

The ANC MASK[7:0] is an 8-bit word that can be used to selectively control extraction of packets with specific

DIDs (or DID ranges) into the FIFO. When the ANC MASK[7:0] is set to FFh, packets with any DID can be

extracted into the FIFO. When any bit or bits of the ANC MASK[7:0] are set to a logic-1, the corresponding bit or

bits of the ANC ID[7:0] are a don't-care when matching DIDs of packets being extracted. When the ANC

MASK[7:0] is set to 00h, the ANC DID of incoming packets must match exactly, bit-for-bit the ANC ID[7:0] set in

the control register for the packets to be extracted into the FIFO. The initial value of the ANC MASK[7:0] is FFh

and the ANC ID[7:0] is 00h.

Similarly, ANC MASK[15:8] is an 8-bit word that can be used to selectively control extraction of packets with

specific SDID/DBN (or SDID/DBN ranges) into the FIFO. Operation and use of these bits is the same as for ANC

MASK[7:0] previously discussed.

Product Folder Links: LMH0031

LMH0031

SNLS218A –JANUARY 2006–REVISED APRIL 2013

www.ti.com

ANC 5 (Address 17h)

The FIFO EXTRACT ENABLE bit in the control registers enables the device to extract or copy Ancillary Data

from the video data stream and place it in the ANC FIFO. From there data may be output via the parallel ancillary

port. Data extraction is enabled when this bit is set to a logic-1. This bit can be used to delay automatic

extraction and therefore the output of parallel Ancillary Data. FIFO EXTRACT ENABLE should be asserted

during an SAV or EAV to avoid timing problems with Ancillary Data extraction. Access to data in the FIFO is

controlled by the RD/WR,ANC/CTRL and ACLK control signals.

To conserve power when the Ancillary Data function is not being used, the internal Ancillary Data FIFO clock is

disabled. This clock must be enabled before Ancillary Data may be replicated into the FIFO for output. FIFO

CLOCK ENABLE, bit-6 of the ANC 5 register (address 17h), when set, enables this clock to propagate to the

FIFO. The default condition of FIFO CLOCK ENABLE is OFF. After enabling the internal FIFO clock by turning

this bit ON, ACLK must be toggled three (3) times to propagate the enable to the clock tree. ACLK should remain

running at all times when the ANC FIFO is in use. Otherwise, message tracking and related functions will not

operate correctly.

The LMH0031 can keep track of up to 8 ANC data packets in the ANC FIFO. Incoming packet length versus

available space in the FIFO is also tracked. The MSG TRACK bit in the control registers, when set, enables

tracking of packets in the FIFO. Other functions for control of packet traffic in the FIFO are FIFO FLUSH STAT

and MSG FLUSH STAT. If the user wishes to handle more than 8 messages, the MSG TRACK bit should be

turned off (reset). The operation FIFO FLUSH STAT will no longer work and the function FULL MSG

AVAILABLE will no longer be a reliable indicator that messages are available in the FIFO. The user may still

effectively use the FIFO by monitoring the states of ANC FIFO EMPTY,ANC FIFO FULL,ANC FIFO 90%FULL

and ANC FIFO OVERRUN.

Setting the FIFO FLUSH STAT bit to a logic-1 flushes the FIFO. FIFO FLUSH STAT may not be set while the

FIFO is being accessed (Read or Write). FIFO FLUSH STAT is automatically reset after this operation is

complete.

When MSG FLUSH STAT is set to a logic-1, the oldest message packet in the FIFO is flushed when data is not

being written to the FIFO. MSG FLUSH STAT is automatically reset after this operation is complete.

The FULL MSG AVAILABLE bit in the control registers, when set, notifies the host system that complete

packets reside in the Ancillary Data FIFO. When this bit is not set, the messages in the FIFO are incomplete or

partial. This function is not affected by MSG TRACK. The FULL MSG AVAILABLE function is most useful when

mapped to the multifunction I/O port as an output.

ANC 6 (Address 18h)

The ANC FIFO 90% FULL flag bit indicates when the ANC FIFO is 90% full. This bit may be mapped to the

multi-function I/O port. The purpose of this flag is to provide a signal which gives the host system time to begin

reading from the FIFO before it has the chance to overflow. This was done because it is virtually impossible to

monitor the FIFO FULL flag and begin extracting from the FIFO before an overrun condition occurs.

The SHORT MSG DETECT flag bit indicates when short ANC messages have been detected. i.e. An ANC

header was detected before the last full message was recovered. This bit may be mapped to the multi-function

I/O port.

The ANC PARITY MASK bit when set disables parity checking for DID and SDID words in the ANC data packet.

When reset, parity checking is enabled; and, if a parity error occurs, the packet will not be extracted.

The VANC bit, when set, enables extraction of ANC data present in the vertical blanking interval (both active

video and horizontal blanking portions of the line).

FORMAT 0 (Address 0Bh)

The LMH0031 may be set to process a single video format by writing the appropriate data into the FORMAT 0

specified type of SD or HD formats defined by a particular SMPTE specification. The Format Set[4:0] bits may

not be used to confine device operation to a range of standards. The available formats and codes are detailed in

Table 4. Generally speaking, the Format Set[4:0] codes indicate or group the formats as follows: Format Set[4]

is set for the HD data formats, reset for SD data formats. Format Set[3] is set for PAL data formats (with the

exception of the SMPTE 274M 24-frame progressive format), reset for NTSC data formats. Format Set[2:0]

further sub-divide the standards as given in the table.

Product Folder Links: LMH0031

LMH0031

www.ti.com

SNLS218A –JANUARY 2006–REVISED APRIL 2013

Table 4. Video Raster Format Parameters

Format Frame Active

Code Format Spec.(1) Lines Active Lines Samples

Rate Samples

[4,3,2,1,0]

00001 SDTV, 54 RP 174 60I 525 507/487* 3432 2880

00010 SDTV, 36 SMPTE 267 60I 525 507/487* 2288 1920

00011 SDTV, 27 SMPTE 125 60I 525 507/487* 1716 1440

01001 SDTV, 54 ITU-R BT 601.5 50I 625 577 3456 2880

01010 SDTV, 36 ITU-R BT 601.5 50I 625 577 2304 1920

01011 SDTV, 27 ITU-R BT 601.5 50I 625 577 1728 1440

10001 HDTV, 74.25 SMPTE 260 30I 1125 1035 2200 1920

10010 HDTV, 74.25 SMPTE 274 30I 1125 1080 2200 1920

10011 HDTV, 74.25 SMPTE 274 30P 1125 1080 2200 1920

11001 HDTV, 74.25 SMPTE 274 25I 1125 1080 2640 1920

11010 HDTV, 74.25 SMPTE 274 25P 1125 1080 2640 1920

11100 HDTV, 74.25 SMPTE 295 25I 1250 1080 2376 1920

11101 HDTV, 74.25 SMPTE 274 24P 1125 1080 2750 1920

10100 HDTV, 74.25 SMPTE 296 (1, 2) 60P 750 720 1650 1280

(1) Spec. is ensured by design.

The HD Only bit when set to a logic-1 locks the LMH0031 into the high definition data range and frequency. In

systems designed to handle only high definition signals, enabling HD Only reduces the time required for the

LMH0031 to establish frequency lock and determine the HD format being processed.

The SD Only bit when set to a logic-1 locks the LMH0031 into the standard definition data ranges and

frequencies. In systems designed to handle only standard definition signals, enabling SD Only reduces the time

required for the LMH0031 to establish frequency lock and determine the format being processed. When SD Only

and HD Only are set to logic-0, the device operates in SD/HD mode.

The Framing Mode bit in the Format 0 register and Framing Enable in the Video Info 0 register combine with

Framing Enable to control the manner in which the LMH0031 aligns framing. When Framing Mode and

Framing Enable are both reset, the LMH0031 aligns on the first valid TRS character. If another TRS occurs that

is not on a word boundary, the NSP bit is set until the next TRS that is on a word boundary occurs. When

Framing Mode is set to a logic-1, the LMH0031 operates similarly to the CLC011 when NSP is tied to FE. An

alternative configuration that operates identically can be achieved with the LMH0031 by mapping NSP as an

output and Framing Enable as an input on the Multifunction I/O bus and externally connecting them. In this case

Framing Mode should be reset to a logic-0. When Framing Mode is reset and Framing Enable is set, the

LMH0031 realigns on every valid TRS. The initial state of Framing Mode is set following a reset or at power-on.

FORMAT 1 (Address 0Ch)

The LMH0031 automatically determines the format of the incoming serial data. The result of this operation is

stored in the FORMAT 1 register. The Format[4:0] bits identify which of the many possible video data standards

that the LMH0031 can process is being received. These format codes follow the same arrangement as for the

Format Set[4:0] bits. These formats and codes are given in Table 4. Bit Format[4] when set indicates that HD

data is being processed. When reset, SD data is indicated. Format[3] when set indicates that PAL data is being

processed. When reset NTSC data is being processed. Format[2:0] correspond with one of the sub-standards

given in the table. Note that the LMH0031 does not distinguish or log the data rate differences between HD data

at 74.25Mhz and 74.25MHz/1.001.

The H, V, and F bits correspond to input TRS data bits 6, 7 and 8, respectively. The meaning and function of this

data is the same for both standard definition (SMPTE 125M) and high definition (SMPTE 292M luminance and

colour difference) video data. Polarity is logic-1 equals HIGH-true. These bits are registered for the duration of

the applicable field.

Product Folder Links: LMH0031

LMH0031

SNLS218A –JANUARY 2006–REVISED APRIL 2013

www.ti.com

TEST 0 REGISTER (Address 0Dh)

The Test Pattern Select bits determine which test pattern is output when the Test Pattern Generator (TPG)

mode or the Built-in Self-Test (BIST) mode is enabled. Table 5 gives the codes corresponding to the various test

patterns. All HD colour bar test patterns are inherently BIST data. BIST test patterns for SD are: NTSC, 27MHz,

4x3 Colour Bars and PAL, 27MHz, 4x3 PLL Pathological.

The TPG Enable bit when set to a logic-1 enables the Test Pattern Generator function and built-in self-test

(BIST).

The Pass/Fail bit indicates the result of the built-in self-test. This bit is a logic-1 for a pass condition.

Table 5. Test Pattern Selection Codes(1)

Test Pattern Select Word Bits > Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

1=HD 1=Progressive 00=Black

0=Interlaced 01=PLL Path.

Video Raster Standard 0=SD 1=PAL 10=EQ Path.

0=NTSC 11=Colour Bars

1125 Line, 74.25 MHz, 30 Frame Interlaced Component (SMPTE 260M)

Ref. Black 1 0 0 0 0 0

PLL Path. 1 0 0 0 0 1

EQ Path. 1 0 0 0 1 0

Colour Bars 1 0 0 0 1 1

1125 Line, 74.25 MHz, 30 Frame Interlaced Component (SMPTE 274M)

Ref. Black 1 0 0 1 0 0

PLL Path. 1 0 0 1 0 1

EQ Path. 1 0 0 1 1 0

Colour Bars 1 0 0 1 1 1

1125 Line, 74.25 MHz, 25 Frame Interlaced Component (SMPTE 274M)

Ref. Black 1 0 1 0 0 0

PLL Path. 1 0 1 0 0 1

EQ Path. 1 0 1 0 1 0

Colour Bars 1 0 1 0 1 1

1125 Line, 74.25 MHz, 25 Frame Interlaced Component (SMPTE 295M)

Ref. Black 1 0 1 1 0 0

PLL Path. 1 0 1 1 0 1

EQ Path. 1 0 1 1 1 0

Colour Bars 1 0 1 1 1 1

1125 Line, 74.25 MHz, 30 Frame Progressive Component (SMPTE 274M)

Ref. Black 1 1 0 0 0 0

PLL Path. 1 1 0 0 0 1

EQ Path. 1 1 0 0 1 0

Colour Bars 1 1 0 0 1 1

1125 Line, 74.25 MHz, 25 Frame Progressive Component (SMPTE 274M)

Ref. Black 1 1 0 1 0 0

PLL Path. 1 1 0 1 0 1

EQ Path. 1 1 0 1 1 0

Colour Bars 1 1 0 1 1 1

1125 Line, 74.25 MHz, 24 Frame Progressive Component (SMPTE 274M)

Ref. Black 1 1 1 0 0 0

PLL Path. 1 1 1 0 0 1

EQ Path. 1 1 1 0 1 0

(1) Note: BIST test patterns for SD are: NTSC 4x3 Colour Bars and PAL 4x3 PLL Pathological.

Product Folder Links: LMH0031

LMH0031

www.ti.com

SNLS218A –JANUARY 2006–REVISED APRIL 2013

Table 5. Test Pattern Selection Codes(1) (continued)

Test Pattern Select Word Bits > Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

Colour Bars 1 1 1 0 1 1

750 Line, 74.25 MHz, 60 Frame Progressive Component (SMPTE 296M)

Ref. Black 1 1 1 1 0 0

PLL Path. 1 1 1 1 0 1

EQ Path. 1 1 1 1 1 0

Colour Bars 1 1 1 1 1 1

525 Line, 30 Frame, 27 MHz, NTSC 4x3 (SMPTE 125M)

Ref. Black 0 0 0 0 0 0

PLL Path. 0 0 0 0 0 1

EQ Path. 0 0 0 0 1 0

Colour Bars (SD BIST) 0 0 0 0 1 1

625 Line, 25 Frame, 27 MHz, PAL 4x3 (ITU-T BT.601)

Ref. Black 0 1 0 0 0 0

PLL Path. (SD BIST) 0 1 0 0 0 1

EQ Path. 0 1 0 0 1 0

Colour Bars 0 1 0 0 1 1

525 Line, 30 Frame, 36 MHz, NTSC 16x9 (SMPTE 125M)

Ref. Black 0 0 0 1 0 0

PLL Path. 0 0 0 1 0 1

EQ Path. 0 0 0 1 1 0

Colour Bars 0 0 0 1 1 1

625 Line, 25 Frame, 36 MHz, PAL 16x9 (ITU-T BT.601)

Ref. Black 0 1 0 1 0 0

PLL Path. 0 1 0 1 0 1

EQ Path. 0 1 0 1 1 0

Colour Bars 0 1 0 1 1 1

525 Line, 30 Frame, 54 MHz (NTSC)

Ref. Black 0 0 1 0 0 0

PLL Path. 0 0 1 0 0 1

EQ Path. 0 0 1 0 1 0

Colour Bars 0 0 1 0 1 1

625 Line, 25 Frame, 54 MHz (PAL)

Ref. Black 0 1 1 0 0 0

PLL Path. 0 1 1 0 0 1

EQ Path. 0 1 1 0 1 0

Colour Bars 0 1 1 0 1 1

VIDEO INFO 0 REGISTER (Address 0Eh)

Re-synchronization of the parallel video output data with the parallel rate clock is controlled by the functions

Framing Enable,Framing Mode and NSP. For operating details about these control bits, refer to the

preceeding section about Format Registers 0 and 1 and the Format Mode bit. Framing Enable may be

assigned as an input on the multi-function I/O port.

The NSP (New Sync Position) bit indicates that a new or out-of-place TRS character has been detected in the

input data. This bit is set to a logic-1 and remains set for at least one horizontal line period or unless re-activated

by a subsequent new or out-of-place TRS. It is reset by an EAV TRS character.

The EAV (end of active video) and SAV (start of active video) bits track the occurrence of the corresponding

TRS characters.

Product Folder Links: LMH0031

LMH0031

SNLS218A –JANUARY 2006–REVISED APRIL 2013

www.ti.com

The Lock Detect is a logic-1 when the loop is locked and the CDR has acquired a phase of the incoming serial

data. This bit may be programmed as an output on the multi-function I/O bus. This bit is mapped to I/O port bit 4

in the default condition.

The VPG Filter Enable bit when set enables operation of the Video Pattern Generator filter. Operation of this

filter causes the insertion of transition codes in the chroma and luma data of colour bar test patterns where these

patterns change from one bar to the next. This filter reduces the magnitude of out-of-band frequency products

which are produced by abrupt transitions in the chroma and luma data when fed to D-to-A converters and picture

monitors.

The LMH0031 incorporates circuitry that implements a method for handling data that has been subjected to LSB

dithering. Data from the de-scrambler is routed for de-dithering. Control of this circuitry is via the De-Dither

Enable bit in the VIDEO INFO 0 control register. Recovery of data that has been dithered during the vertical

blanking interval can be selectively enabled by use of the V De-Dither Enable bit in the VIDEO INFO 0 control

VIDEO CONTROL 0 (register address 55h)

The EXTERNAL VCLK bit is a special application function which enables use of an external VCXO as a substitute

for the internally generated VCLK. Additional circuitry is enabled within the LMH0031 which provides phase-

frequency detection and control voltage output for the VCXO. An external loop filter and voltage amplifier are

required to interface the control voltage output to the VCXO frequency control input. When this function is used,

the RBB output function is changed from the bias supply output to the control voltage output of the phase-

frequency detector. The VCLK output changes function, becoming the input for the VCXO signal. Use of this

function and required external support circuitry is explained in the Application Information section.

The SYNC DETECT ENABLE bit, when set, enables detection of TRS characters. This bit is normally set (ON).

The LSB CLIP ENABLE bit, when set, causes the two LSBs of TRS characters to be set to 00b as described in

ITU-R BT.601. This function is normally set (ON).

The NRZI ENABLE bit, when set, enables data to be converted from NRZI to NRZ. This bit is normally set (ON).

The DE-SCRAMBLE ENABLE bit, when set, enables de-scrambling of the incoming data according to

requirements of SMPTE 259M or SMPTE 292M. This bit is normally set (ON).

CAUTION

The default state of this register is 36h. If any of the normal operating features of the

descrambler are turned off, this register’s default data must be restored to resume

normal device operation.

REFERENCE CLOCK REGISTER (Address 67h)

The Reference Clock register controls operation of the CDR reference clock source. The CLKEN bit when reset

to a logic-0 enables the oscillator signal to be used by the LMH0031 as a reference. The default state of this bit

at power-on is enabled. In general, this function and bit should not be disabled. The INT_OSC EN bit enables the

internal crystal oscillator amplifier. By default this bit is a logic-0 and is therefore inactive at power-on. The device

expects an external 27MHz reference reference clock source to be connected to the XTALi/Ext Clk pin and

activated at power-on.

I/O PIN 0 THROUGH 7 CONFIGURATION REGISTERS (Addresses 0Fh through 16h)

The I/O Pin Configuration Registers are used to map individual bits of the multi-function I/O port to selected

bits of the Configuration and Control Registers. Table 6 gives the pin select codes for the Configuration and

Control register functions that may be mapped to the port. Pin[n] Select [5] controls whether the port pin is input

or output. The port pin will be an input when this bit is set and an output when reset. Input-only functions may not

be configured as outputs and vice versa. The remaining five Pin[n] Select [4:0] bits identify the particular Control

Product Folder Links: LMH0031

LMH0031

www.ti.com

SNLS218A –JANUARY 2006–REVISED APRIL 2013

Example: Program, via the AD port, I/O port bit 0 as output for the CRC Luma Error bit in the control registers.

1. Set ANC/CTRL to a logic-low.

2. Set RD/WR to a logic-low.

3. Present 00Fh to AD[9:0] as the I/O PIN 0 CONFIG register address.

4. Toggle ACLK.

5. Present 310h to AD[9:0] as the register data, the bit address of the CRC Luma Error bit in the control

registers.

6. Toggle ACLK.

Table 6. Control Register Bit, Pin[n] SEL[5:0] Codes for I/O Port Pin Mapping(1)

Pin[n] SEL[5:0] Codes I/P or

O/P

[5] [4] [3] [2] [1] [0] HEX

reserved 0 0 0 0 0 0 00 O/P

FF Flag Error 0 0 0 0 0 1 01 O/P

AP Flag Error 0 0 0 0 1 0 02 O/P

ANC Flag Error 0 0 0 0 1 1 03 O/P

CRC Error (SD/HD) 0 0 0 1 0 0 04 O/P I/O Port Bit 5

Addresses 05h and 06h are reserved

ANC FIFO 90% FULL 0 0 0 1 1 1 07 O/P

SHORT MSG DETECT 0 0 1 0 0 0 08 O/P

FULL MSG AVAIL 0 0 1 0 0 1 09 O/P

Addresses 0Ah through 0Ch are reserved

SAV 0 0 1 1 0 1 0D O/P

EAV 0 0 1 1 1 0 0E O/P I/O Port Bit 7

NSP 0 0 1 1 1 1 0F O/P

CRC Luma Error 0 1 0 0 0 0 10 O/P

CRC Chroma Error 0 1 0 0 0 1 11 O/P

F 0 1 0 0 1 0 12 O/P I/O Port Bit 0

V 0 1 0 0 1 1 13 O/P I/O Port Bit 1

H 0 1 0 1 0 0 14 O/P I/O Port Bit 2

Format[0] 0 1 0 1 0 1 15 O/P

Format[1] 0 1 0 1 1 0 16 O/P

Format[2] 0 1 0 1 1 1 17 O/P

Format[3] 0 1 1 0 0 0 18 O/P

Format[4] 0 1 1 0 0 1 19 O/P I/O Port Bit 3 (SD/HD)

FIFO Full 0 1 1 0 1 0 1A O/P

FIFO Empty 0 1 1 0 1 1 1B O/P I/O Port Bit 6

Lock Detect 0 1 1 1 0 0 1C O/P I/O Port Bit 4

Pass/Fail 0 1 1 1 0 1 1D O/P

FIFO Overrun 0 1 1 1 1 0 1E O/P

ANC Chksum Error 0 1 1 1 1 1 1F O/P

EDH Force 1 0 0 0 0 0 20 I/P

Test Pattern Select[0] 1 0 0 0 0 1 21 I/P

Test Pattern Select[1] 1 0 0 0 1 0 22 I/P

Test Pattern Select[2] 1 0 0 0 1 1 23 I/P

Test Pattern Select[3] 1 0 0 1 0 0 24 I/P

Test Pattern Select[4] 1 0 0 1 0 1 25 I/P

Test Pattern Select[5] 1 0 0 1 1 0 26 I/P

(1) Note: All LVCMOS inputs have internal pull-down devices except VCLK and ACLK.

Product Folder Links: LMH0031

LMH0031

SNLS218A –JANUARY 2006–REVISED APRIL 2013

www.ti.com

Table 6. Control Register Bit, Pin[n] SEL[5:0] Codes for I/O Port Pin Mapping(1) (continued)

Pin[n] SEL[5:0] Codes I/P or

O/P

[5] [4] [3] [2] [1] [0] HEX

EDH Enable 1 0 0 1 1 1 27 I/P

TPG Enable 1 0 1 0 0 0 28 I/P

Addresses 29h through 2Bh are reserved

VPG Filter Enable 1 0 1 1 0 0 2C I/P

De-Dither Enable 1 0 1 1 0 1 2D I/P

Framing Enable 1 0 1 1 1 0 2E I/P

FIFO Extract Enable 1 0 1 1 1 1 2F I/P

PIN DESCRIPTIONS

Pin Name Description

1 AD9 Ancillary Data Output, Control Data Input

2 AD8 Ancillary Data Output, Control Data Input

3 AD7 Ancillary Data Output, Control Data Input

4 AD6 Ancillary Data Output, Control Data Input

5 AD5 Ancillary Data Output, Control Data Input

6 VSSD Negative Power Supply Input (2.5V supply, Digital Logic)

7 AD4 Ancillary Data Output, Control Data Input

8 AD3 Ancillary Data Output, Control Data Input

9 AD2 Ancillary Data Output, Control Data Input

10 AD1 Ancillary Data Output, Control Data Input

11 AD0 Ancillary Data Output, Control Data Input

12 VDDD Positive Power Supply Input (2.5V supply, Digital Logic)

13 ACLK ancillary/Control Clock Input

14 IO7 Multi-Function I/O Port

15 IO6 Multi-Function I/O Port

16 IO5 Multi-Function I/O Port

17 IO4 Multi-Function I/O Port

18 IO3 Multi-Function I/O Port

19 IO2 Multi-Function I/O Port

20 VSSIO Negative Power Supply Input (3.3V supply, I/O)

21 DV19 Parallel Video Output (HD=Luma)

22 DV18 Parallel Video Output (HD=Luma)

23 DV17 Parallel Video Output (HD=Luma)

24 DV16 Parallel Video Output (HD=Luma)

25 DV15 Parallel Video Output (HD=Luma)

26 VDDIO Positive Power Supply Input (3.3V supply, I/O)

27 DV14 Parallel Video Output (HD=Luma)

28 DV13 Parallel Video Output (HD=Luma)

29 DV12 Parallel Video Output (HD=Luma)

30 DV11 Parallel Video Output (HD=Luma)

31 DV10 Parallel Video Output (HD=Luma)

32 VSSD Negative Power Supply Input (2.5V supply, Digital Logic)

33 VDDD Positive Power Supply Input (2.5V supply, Digital Logic)

34 DV9 Parallel Video Output (HD=Chroma, SD=Luma & Chroma)

35 DV8 Parallel Video Output (HD=Chroma, SD=Luma & Chroma)

36 DV7 Parallel Video Output (HD=Chroma, SD=Luma & Chroma)

Product Folder Links: LMH0031

LMH0031

www.ti.com

SNLS218A –JANUARY 2006–REVISED APRIL 2013

PIN DESCRIPTIONS (continued)

Pin Name Description

37 DV6 Parallel Video Output (HD=Chroma, SD=Luma & Chroma)

38 DV5 Parallel Video Output (HD=Chroma, SD=Luma & Chroma)

39 VSSD Negative Power Supply Input (2.5V supply, Digital Logic)

40 DV4 Parallel Video Output (HD=Chroma, SD=Luma & Chroma)

41 DV3 Parallel Video Output (HD=Chroma, SD=Luma & Chroma)

42 DV2 Parallel Video Output (HD=Chroma, SD=Luma & Chroma)

43 DV1 Parallel Video Output (HD=Chroma, SD=Luma & Chroma)

44 DV0 Parallel Video Output (HD=Chroma, SD=Luma & Chroma)

45 IO1 Multi-Function I/O Port

46 IO0 Multi-Function I/O Port

47 VSSIO Negative Power Supply Input (3.3V supply, I/O)

48 VDDIO Positive Power Supply Input (3.3V supply, I/O)

49 RESET Manual Reset Input (High True)

50 VCLK Parallel Video Data Clock Output

51 VDDPLL Positive Power Supply Input (2.5V supply, PLL)

52 VSSPLL Negative Power Supply Input (2.5V supply, PLL)

53 RREF Current Reference Resistor

54 RBB SDI Bias Supply Resistor

55 VSSSI Negative Power Supply Input (3.3V supply, Serial Input)

56 SDI Serial Data Complement Input

57 SDI Serial Data True Input

58 VDDSI Positive Power Supply Input (3.3V supply, Serial Input)

59 VSSIO Negative Power Supply Input (3.3V supply, I/O)

60 XTALi/EXT CLK Crystal or External 27MHz Clock Input

61 XTALo Crystal (Oscillator Output)

62 VDDD Positive Power Supply Input (2.5V supply, Digital Logic)

63 ANC/CTRL ancillary/Control Data Port Function Control Input

64 RD/WR ancillary/Control Data Port Read/Write Control Input

Product Folder Links: LMH0031

LMH0031

SNLS218A –JANUARY 2006–REVISED APRIL 2013

www.ti.com

Application Information

A typical application circuit for the LMH0031 is shown in the Application Circuit diagram. This circuit

demonstrates the capabilities of the LMH0031 and allows its evaluation in a native configuration. An assembled

demonstration board is available, part number SD131EVK. The board may be ordered through any of TI's sales

offices. Complete circuit board layouts and schematics for the SD131EVK are available on TI's WEB site. For

latest availability information, please see: www.ti.com/appinfo/interface.

PCB LAYOUT AND POWER SYSTEM BYPASS RECOMMENDATIONS

Circuit board layout and stack-up for the LMH0031 should be designed to provide noise-free power to the device.

Good layout practice also will separate high frequency or high-level inputs and outputs from low-level inputs to

minimize unwanted stray noise pickup, feedback and interference. Power system performance may be greatly

improved by using thin dielectrics (4 to 10 mils) for power/ground sandwiches. This increases the intrinsic

capacitance of the PCB power system which improves power supply filtering, especially at high frequencies, and

makes the value and placement of external bypass capacitors less critical. External bypass capacitors should

include both RF ceramic and tantalum electrolytic types. RF capacitors may use values in the range 0.01 µF to

0.1 µF. Tantalum capacitors may be in the range 2.2 µF to 10 µF. Voltage rating for tantalum capacitors should

be at least 5X the power supply voltage being used. It is recommended practice to use two vias at each power

pin of the LMH0031 as well as all RF bypass capacitor terminals. Dual vias reduce the interconnect inductance

by up to half, thereby extending the effective frequency range of the bypass components.

The outer layers of the PCB may be flooded with additional VSS (ground) plane. These planes will improve

shielding and isolation as well as increase the intrinsic capacitance of the power supply plane system. Naturally,

to be effective, these planes must be tied to the VSS power supply plane at frequent intervals with vias. Frequent

via placement also improves signal integrity on signal transmission lines by providing short paths for image

currents which reduces signal distortion. The planes should be pulled back from all transmission lines and

component mounting pads a distance equal to the width of the widest transmission line or the thickness of the

dielectric separating the transmission line from the internal power or ground plane(s) whichever is greater. Doing

so minimizes effects on transmission line impedances and reduces unwanted parasitic capacitances at

component mounting pads.

In especially noisy power supply environments, such as is often the case when using switching power supplies,

separate filtering may be used at the LMH0031's PLL and serial input power pins. The LMH0031 was designed

for this situation. The I/O, digital section, PLL and serial input power supply feeds are independent (see table and

Block Diagram for details). Supply filtering may take the form of L-section or pi-section, L-C filters in series with

these VDD inputs. Such filters are available in a single package from several manufacturers. Device power

supplies must be either sequenced as described in POWER SUPPLIES, POWER-ON-RESET AND RESET

INPUT and ideally should be applied simultaneously as from a common source.

MAINTAINING OUTPUT DATA INTEGRITY

The way in which the TRS and other video data characters are specified and are therefore output in parallel form

can result in the simultaneous switching of many of the LMH0031’s CMOS outputs. Such switching can lead to

the production of output high level droop or low level ground bounce. Given in the specifications, VOLP is the peak

output LOW voltage or ground bounce and VOHV is the lowest output HIGH voltage or output droop that may

occur under dynamic simultaneous output switching conditions. VOHV and VOLP are measured with respect to

reference ground. Careful attention to PCB layout, power pin connections to the power planes and timing of the

output data clocking can reduce these effects. Consideration must also be given to the timing allocated to

external circuits which sample the outputs.

The effects of simultaneous output switching on output levels may be minimized by adopting good PCB layout

and data output timing practices, especially critical at HD data rates. The power pins feeding the I/O should have

low inductance connections to the power and ground planes. It is recommended that these connections use at

least two vias per power or ground pin. Short interconnecting traces consistent with good layout practices and

soldering rules must be used. Sampling or clocking of data by external devices should be so timed as to take

maximum advantage of the steady-state portion of the parallel output data interval. The LMH0031 is designed so

that video data will be stable at the positive-going transition of VCLK. Data should not be sampled close to the

data transition intervals associated with the negative-going clock edge. The specified propagation delay and

clock to data timing parameters must be observed. When data is being sampled from the video data port

together with the ANC port and/or I/O port, it is recommended that the sampling clocks be synchronized with the

video clock, VCLK, to minimize possible effects from ground bounce or output droop on sampled signal levels.

Product Folder Links: LMH0031

LMH0031

www.ti.com

SNLS218A –JANUARY 2006–REVISED APRIL 2013

PROCESSING NON-SUPPORTED RASTER FORMATS

The number and type of HD raster formats has proliferated since the LMH0031 was designed. Though not

specifically capable of fully or automatically processing these new formats, the LMH0031 may still be capable of

deserializing them. The user is encouraged to experiment with processing these formats, keeping in mind that

the LMH0031 has not been tested to handle formats other than those detailed in Table 4. Therefore, the results

from attempts to process non-supported formats is not ensured. The following guidelines concerning device

setup are provided to aid the user in configuring the LMH0031 to attempt limited processing of these other raster

formats.

In general, the device is configured to defeat its automatic format detection function and to limit operation to a

general HD format. (The user should consult Table 4 for guidance on the format groups similar to the non-

supported one to be processed). Since most non-supported formats are in the HD group, the LMH0031 should

be configured to operate in HD-ONLY mode by setting bit-5 of the FORMAT 0 register (address 0Bh). Also, the

device should be further configured by loading the FORMAT SET[4:0] bits of this register with the general HD

sub-format code. In addition, since control data is being written to the port, AD[9:8] must be driven as 11b. The

complete data word for this general HD sub-format code with HD-ONLY bit set is 33Fh. Since this format differs

from those in the table, the EAV/SAV indicators are disabled. Without these indicators, line numbering and CRC

processing are disabled and ANC data extraction will not function. Output video chroma and luma data will be

word-aligned. Post-processing of the parallel data output from the LMH0031 will be needed to implement CRC

checking or line number tracking.

USING EXTERNAL VCXO FOR VCLK

The EXTERNAL VCLK bit of VIDEO CONTROL 0 (register address 55h) is a special application function which

enables use of an external VCXO as a substitute for the internally generated VCLK. Additional circuitry is enabled

within the LMH0031 which provides phase-frequency detection and control voltage output for the VCXO. An

external loop filter and voltage amplifier are required to interface the control voltage output to the VCXO

frequency control input. When this function is used, the RBB output function is changed from the bias supply

output to the control voltage output of the phase-frequency detector. The VCLK output changes function,

becoming the input for the VCXO signal.

Figure 8 shows an example using dual VCXOs for VCLK to handle both standard and high definition video.

Product Folder Links: LMH0031

100 k:

182 k:

VCTRL FOUT

LMC7101 +3.3V

VCTRL FOUT

+3.3V

NC7SZ126

74.25 MHz

VCXO

27.00 MHz

VCXO

LMH0031

RB B

RREF

VCLK

22.1 k:100 pF

10 nF 4.75 k:

DV[19:0]

To other

logic or

serializer

CAUTION! Read text

before using this

circuit.

NC7SZ125

NC7SZ08

CLC031 IO3 - SD/HD

CLC031 IO4 - Lock Detect

22.1:

LMH0031

SNLS218A –JANUARY 2006–REVISED APRIL 2013

www.ti.com

Figure 8. Using Dual VCXOs for VCLK Example

The control voltage output from RBB is externally filtered by the loop filter consisting of a 22.1kΩresistor in series

with a 10nF capacitor, combined in parallel with a 100pF capacitor. This gives a loop bandwidth of 1.5kHz. Since

the control voltage is limited to around 2.1V, it requires a level shifter to get the entire pull range on the VCXO.

TI's LMC7101 is recommended with 100kΩand 182kΩresistors as shown in Figure 8 to provide a gain of 1.55,

sufficient to drive a 3.3V VCXO.

Recommended VCXOs from SaRonix (141 Jefferson Drive, Menlo Park, CA 94025, USA) include the

ST1308AAB-74.25 for high definition and the ST1307BAB-27.00 for standard definition. Dual VCXOs require

some supporting logic to select the appropriate VCXO. This requires the use of Format[4] (SD/HD) and Lock

Detect, which are mapped at power-on to I/O Port Bit 3 and I/O Port Bit 4, respectively. These two signals pass

through an AND gate (Fairchild Semiconductor's NC7SZ08 or similar). Its output is high when both Lock Detect

and Format[4] are high, which indicates a valid high-definition signal is present. The VCXOs are buffered to

control the transition times and to allow easy selection. The output of the AND gate is used to control the Output

Enable (OE) function of the buffers. The 74.25MHz VCXO is buffered with the NC7SZ126 with the AND gate

output connected to the OE pin of the NC7SZ126, and the 27.00MHz VCXO is buffered with the NC7SZ125 with

the AND gate output connected to the OE pin of the NC7SZ125. This circuit uses the 27.00MHz VCXO as

default and enables the 74.25MHz VCXO when a valid high-definition signal is present. The outputs from the

buffers are daisy-chained together and sent to the LMH0031's VCLK in addition to other devices, such as the

LMH0030 serializer.

Product Folder Links: LMH0031

LMH0031

www.ti.com

SNLS218A –JANUARY 2006–REVISED APRIL 2013

REVISION HISTORY

Changes from Original (April 2013) to Revision A Page

• Changed layout of National Data Sheet to TI format .......................................................................................................... 34

Product Folder Links: LMH0031

PACKAGE OPTION ADDENDUM

www.ti.com 24-Nov-2013

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

LMH0031VS NRND TQFP PAG 64 160 TBD Call TI Call TI 0 to 70 L031

LMH0031VS/NOPB ACTIVE TQFP PAG 64 160 Green (RoHS

& no Sb/Br) CU SN Level-3-260C-168 HR 0 to 70 L031

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability

information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that

lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between

the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight

in homogeneous material)

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish

value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

PACKAGE OPTION ADDENDUM

www.ti.com 24-Nov-2013

Addendum-Page 2

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

MECHANICAL DATA

MTQF006A – JANUARY 1995 – REVISED DECEMBER 1996

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PAG (S-PQFP-G64) PLASTIC QUAD FLATPACK

0,13 NOM

0,25

0,45

0,75

Seating Plane

0,05 MIN

4040282/C 11/96

Gage Plane

0,17

0,27

7,50 TYP

9,80

1,05

0,95

11,80

12,20

1,20 MAX

10,20 SQ

0,08

0,50 M

0,08

0°–7°

NOTES: A. All linear dimensions are in millimeters.

B. This drawing is subject to change without notice.

C. Falls within JEDEC MS-026

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other

changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest

issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and

complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale

supplied at the time of order acknowledgment.

TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms

and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary

to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily

performed.

TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and

applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information

published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or

endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration

and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered

documentation. Information of third parties may be subject to additional restrictions.

Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service

voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.

TI is not responsible or liable for any such statements.

Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements

concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support

that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which

anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause

harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use

of any TI components in safety-critical applications.

In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to

help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and

requirements. Nonetheless, such components are subject to these terms.

No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties

have executed a special agreement specifically governing such use.

Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in

military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components

which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and

regulatory requirements in connection with such use.

TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of

non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products Applications

Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive

Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications

Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers

DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps

DSP dsp.ti.com Energy and Lighting www.ti.com/energy

Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial

Interface interface.ti.com Medical www.ti.com/medical

Logic logic.ti.com Security www.ti.com/security

Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com

Wireless Connectivity www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Texas Instruments:

LMH0031VS LMH0031VS/NOPB