Kinetis KL25 Sub-Family
48 MHz Cortex-M0+ Based Microcontroller with USB
Designed with efficiency in mind. Compatible with all other
Kinetis L families as well as Kinetis K2x family. General purpose
MCU with USB 2.0, featuring market leading ultra low-power to
provide developers an appropriate entry-level 32-bit solution.
This product offers:
Run power consumption down to 47 μA/MHz in very low
power run mode
Static power consumption down to 2 μA with full state
retention and 4 μs wakeup
Ultra-efficient Cortex-M0+ processor running up to 48 MHz
with industry leading throughput
Memory option is up to 128 KB flash and 16 KB RAM
Energy-saving architecture is optimized for low power with
90 nm TFS technology, clock and power gating techniques,
and zero wait state flash memory controller
Performance
48 MHz ARM® Cortex®-M0+ core
Memories and memory interfaces
Up to 128 KB program flash memory
Up to 16 KB SRAM
System peripherals
Nine low-power modes to provide power optimization
based on application requirements
COP Software watchdog
4-channel DMA controller, supporting up to 63 request
sources
Low-leakage wakeup unit
SWD debug interface and Micro Trace Buffer
Bit Manipulation Engine
Clocks
32 kHz to 40 kHz or 3 MHz to 32 MHz crystal oscillator
Multi-purpose clock source
1 kHz LPO clock
Operating Characteristics
Voltage range: 1.71 to 3.6 V
Human-machine interface
Low-power hardware touch sensor interface (TSI)
Up to 66 general-purpose input/output (GPIO)
Communication interfaces
USB full-/low-speed On-the-Go controller with on-
chip transceiver and 5 V to 3.3 V regulator
Two 8-bit SPI modules
One low power UART module
Two UART modules
Two I2C module
Analog Modules
16-bit SAR ADC
12-bit DAC
Analog comparator (CMP) containing a 6-bit DAC
and programmable reference input
Timers
Six channel Timer/PWM (TPM)
Two 2-channel Timer/PWM modules
Periodic interrupt timers
16-bit low-power timer (LPTMR)
Real time clock
MKL25ZxxVFM4
MKL25ZxxVFT4
MKL25ZxxVLH4
MKL25ZxxVLK4
32-pin QFN (FM)
5 x 5 x 1 Pitch 0.5 mm
48-pin QFN (FT)
7 x 7 x 1 Pitch 0.5 mm
64-pin LQFP (LH)
10 x 10 x 1.4 Pitch 0.5
mm
80-pin LQFP (LK)
12 x 12 x 1.4 Pitch 0.5
mm
Freescale Semiconductor, Inc. Document Number: KL25P80M48SF0
Data Sheet: Technical Data Rev 5 08/2014
Freescale reserves the right to change the detail specifications as may be required to
permit improvements in the design of its products. © 2012–2014 Freescale
Semiconductor, Inc. All rights reserved.
Flash write voltage range: 1.71 to 3.6 V
Temperature range (ambient): -40 to 105°C
Security and integrity modules
80-bit unique identification number per chip
Ordering Information 1
Part Number Memory Maximum number of I\O's
Flash (KB) SRAM (KB)
MKL25Z32VFM4 32 4 23
MKL25Z64VFM4 64 8 23
MKL25Z128VFM4 128 16 23
MKL25Z32VFT4 32 4 36
MKL25Z64VFT4 64 8 36
MKL25Z128VFT4 128 16 36
MKL25Z32VLH4 32 4 50
MKL25Z64VLH4 64 8 50
MKL25Z128VLH4 128 16 50
MKL25Z32VLK4 32 4 66
MKL25Z64VLK4 64 8 66
MKL25Z128VLK4 128 16 66
1. To confirm current availability of ordererable part numbers, go to http://www.freescale.com and perform a part number
search.
Related Resources
Type Description Resource
Selector Guide The Freescale Solution Advisor is a web-based tool that features
interactive application wizards and a dynamic product selector.
Solution Advisor
Product Brief The Product Brief contains concise overview/summary information to
enable quick evaluation of a device for design suitability.
KL2 Family Product Brief1
Reference
Manual
The Reference Manual contains a comprehensive description of the
structure and function (operation) of a device.
KL25P80M48SF0RM1
Data Sheet The Data Sheet includes electrical characteristics and signal
connections.
KL25P80M48SF01
Chip Errata The chip mask set Errata provides additional or corrective
information for a particular device mask set.
KINETIS_L_xN97F2
Package
drawing
Package dimensions are provided in package drawings. QFN 32-pin: 98ASA00473D1
QFN 48-pin: 98ASA00466D1
LQFP 64-pin: 98ASS23234W1
LQFP 80-pin: 98ASS23174W1
1. To find the associated resource, go to http://www.freescale.com and perform a search using this term.
2. To find the associated resource, go to http://www.freescale.com and perform a search using this term with the “x
replaced by the revision of the device you are using.
Figure 1 shows the functional modules in the chip.
2Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Memories and
Memory Interfaces
Program
flash
RAM
6-bit DAC
Analog Timers Communication
Interfaces
Security
and Integrity
SPI
x2
Low
power timer
Clocks
Frequency-
Core
Debug
interfaces
Interrupt
controller
comparator
x1
Analog
Human-Machine
Interface (HMI)
System
DMA
Internal
watchdog
locked loop
Phase-
locked loop
reference
Internal
clocks
timers
interrupt
Periodic
oscillator
Low/high
frequency
Low power
UART
x1
®
Cortex™-M0+
ARM
with
GPIOs
interrupt
Kinetis KL25 Family
LEGEND
x2
IC
2
x1
Timers
1x6ch+2x2ch
16-bit ADC
x1
TSI
12-bit DAC
UART
x2
Migration difference from KL15 family
USB LS/FS
x1
BME
MTB
RTC
watchdog
Internal
Figure 1. Functional block diagram
Kinetis KL25 Sub-Family, Rev5 08/2014. 3
Freescale Semiconductor, Inc.
Table of Contents
1 Ratings....................................................................................5
1.1 Thermal handling ratings................................................. 5
1.2 Moisture handling ratings................................................ 5
1.3 ESD handling ratings.......................................................5
1.4 Voltage and current operating ratings............................. 5
2 General................................................................................... 6
2.1 AC electrical characteristics.............................................6
2.2 Nonswitching electrical specifications..............................7
2.2.1 Voltage and current operating requirements....... 7
2.2.2 LVD and POR operating requirements................7
2.2.3 Voltage and current operating behaviors.............8
2.2.4 Power mode transition operating behaviors........ 9
2.2.5 Power consumption operating behaviors............ 10
2.2.6 EMC radiated emissions operating behaviors.....16
2.2.7 Designing with radiated emissions in mind..........17
2.2.8 Capacitance attributes.........................................17
2.3 Switching specifications...................................................17
2.3.1 Device clock specifications..................................17
2.3.2 General switching specifications......................... 18
2.4 Thermal specifications.....................................................18
2.4.1 Thermal operating requirements......................... 18
2.4.2 Thermal attributes................................................19
3 Peripheral operating requirements and behaviors.................. 19
3.1 Core modules.................................................................. 19
3.1.1 SWD electricals .................................................. 19
3.2 System modules.............................................................. 21
3.3 Clock modules................................................................. 21
3.3.1 MCG specifications..............................................21
3.3.2 Oscillator electrical specifications........................23
3.4 Memories and memory interfaces................................... 25
3.4.1 Flash electrical specifications..............................25
3.5 Security and integrity modules........................................ 27
3.6 Analog............................................................................. 27
3.6.1 ADC electrical specifications............................... 27
3.6.2 CMP and 6-bit DAC electrical specifications....... 32
3.6.3 12-bit DAC electrical characteristics....................33
3.7 Timers..............................................................................36
3.8 Communication interfaces............................................... 36
3.8.1 USB electrical specifications............................... 36
3.8.2 USB VREG electrical specifications.................... 37
3.8.3 SPI switching specifications................................ 37
3.8.4 Inter-Integrated Circuit Interface (I2C) timing...... 42
3.8.5 UART...................................................................43
3.9 Human-machine interfaces (HMI)....................................43
3.9.1 TSI electrical specifications................................. 43
4 Dimensions............................................................................. 44
4.1 Obtaining package dimensions....................................... 44
5 Pinout......................................................................................44
5.1 KL25 Signal Multiplexing and Pin Assignments...............44
5.2 KL25 pinouts....................................................................47
6 Ordering parts......................................................................... 51
6.1 Determining valid orderable parts....................................51
7 Part identification.....................................................................51
7.1 Description.......................................................................52
7.2 Format............................................................................. 52
7.3 Fields............................................................................... 52
7.4 Example...........................................................................52
8 Terminology and guidelines.................................................... 53
8.1 Definition: Operating requirement....................................53
8.2 Definition: Operating behavior......................................... 53
8.3 Definition: Attribute.......................................................... 54
8.4 Definition: Rating............................................................. 54
8.5 Result of exceeding a rating............................................ 54
8.6 Relationship between ratings and operating
requirements....................................................................55
8.7 Guidelines for ratings and operating requirements..........55
8.8 Definition: Typical value...................................................56
8.9 Typical value conditions.................................................. 57
9 Revision history.......................................................................57
4Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
1 Ratings
1.1 Thermal handling ratings
Table 1. Thermal handling ratings
Symbol Description Min. Max. Unit Notes
TSTG Storage temperature –55 150 °C 1
TSDR Solder temperature, lead-free 260 °C 2
1. Determined according to JEDEC Standard JESD22-A103, High Temperature Storage Life.
2. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices.
1.2 Moisture handling ratings
Table 2. Moisture handling ratings
Symbol Description Min. Max. Unit Notes
MSL Moisture sensitivity level 3 1
1. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices.
1.3 ESD handling ratings
Table 3. ESD handling ratings
Symbol Description Min. Max. Unit Notes
VHBM Electrostatic discharge voltage, human body model –2000 +2000 V 1
VCDM Electrostatic discharge voltage, charged-device
model
–500 +500 V 2
ILAT Latch-up current at ambient temperature of 105 °C –100 +100 mA 3
1. Determined according to JEDEC Standard JESD22-A114, Electrostatic Discharge (ESD) Sensitivity Testing Human
Body Model (HBM).
2. Determined according to JEDEC Standard JESD22-C101, Field-Induced Charged-Device Model Test Method for
Electrostatic-Discharge-Withstand Thresholds of Microelectronic Components.
3. Determined according to JEDEC Standard JESD78, IC Latch-Up Test.
Ratings
Kinetis KL25 Sub-Family, Rev5 08/2014. 5
Freescale Semiconductor, Inc.
1.4 Voltage and current operating ratings
Table 4. Voltage and current operating ratings
Symbol Description Min. Max. Unit
VDD Digital supply voltage –0.3 3.8 V
IDD Digital supply current 120 mA
VIO IO pin input voltage –0.3 VDD + 0.3 V
IDInstantaneous maximum current single pin limit (applies to
all port pins)
–25 25 mA
VDDA Analog supply voltage VDD – 0.3 VDD + 0.3 V
VUSB_DP USB_DP input voltage –0.3 3.63 V
VUSB_DM USB_DM input voltage –0.3 3.63 V
VREGIN USB regulator input –0.3 6.0 V
2 General
2.1 AC electrical characteristics
Unless otherwise specified, propagation delays are measured from the 50% to the 50%
point, and rise and fall times are measured at the 20% and 80% points, as shown in the
following figure.
80%
20%
50%
VIL
Input Signal
VIH
Fall Time
High
Low
Rise Time
Midpoint1
The midpoint is VIL + (VIH - VIL) / 2
Figure 2. Input signal measurement reference
All digital I/O switching characteristics, unless otherwise specified, assume the output
pins have the following characteristics.
CL=30 pF loads
Slew rate disabled
Normal drive strength
General
6Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
2.2 Nonswitching electrical specifications
2.2.1 Voltage and current operating requirements
Table 5. Voltage and current operating requirements
Symbol Description Min. Max. Unit Notes
VDD Supply voltage 1.71 3.6 V
VDDA Analog supply voltage 1.71 3.6 V
VDD – VDDA VDD-to-VDDA differential voltage –0.1 0.1 V
VSS – VSSA VSS-to-VSSA differential voltage –0.1 0.1 V
VIH Input high voltage
2.7 V ≤ VDD ≤ 3.6 V
1.7 V ≤ VDD ≤ 2.7 V
0.7 × VDD
0.75 × VDD
V
V
VIL Input low voltage
2.7 V ≤ VDD ≤ 3.6 V
1.7 V ≤ VDD ≤ 2.7 V
0.35 × VDD
0.3 × VDD
V
V
VHYS Input hysteresis 0.06 × VDD V
IICIO IO pin negative DC injection current—single pin
VIN < VSS–0.3V –3 mA
1
IICcont Contiguous pin DC injection current —regional limit,
includes sum of negative injection currents of 16
contiguous pins
Negative current injection –25 mA
VODPU Open drain pullup voltage level VDD VDD V2
VRAM VDD voltage required to retain RAM 1.2 V
1. All I/O pins are internally clamped to VSS through a ESD protection diode. There is no diode connection to VDD. If VIN
greater than VIO_MIN (= VSS-0.3 V) is observed, then there is no need to provide current limiting resistors at the pads. If
this limit cannot be observed then a current limiting resistor is required. The negative DC injection current limiting
resistor is calculated as R = (VIO_MIN - VIN)/|IICIO|.
2. Open drain outputs must be pulled to VDD.
2.2.2 LVD and POR operating requirements
Table 6. VDD supply LVD and POR operating requirements
Symbol Description Min. Typ. Max. Unit Notes
VPOR Falling VDD POR detect voltage 0.8 1.1 1.5 V
Table continues on the next page...
General
Kinetis KL25 Sub-Family, Rev5 08/2014. 7
Freescale Semiconductor, Inc.
Table 6. VDD supply LVD and POR operating requirements (continued)
Symbol Description Min. Typ. Max. Unit Notes
VLVDH Falling low-voltage detect threshold — high
range (LVDV = 01)
2.48 2.56 2.64 V
VLVW1H
VLVW2H
VLVW3H
VLVW4H
Low-voltage warning thresholds — high range
Level 1 falling (LVWV = 00)
Level 2 falling (LVWV = 01)
Level 3 falling (LVWV = 10)
Level 4 falling (LVWV = 11)
2.62
2.72
2.82
2.92
2.70
2.80
2.90
3.00
2.78
2.88
2.98
3.08
V
V
V
V
1
VHYSH Low-voltage inhibit reset/recover hysteresis —
high range
±60 mV
VLVDL Falling low-voltage detect threshold — low
range (LVDV=00)
1.54 1.60 1.66 V
VLVW1L
VLVW2L
VLVW3L
VLVW4L
Low-voltage warning thresholds — low range
Level 1 falling (LVWV = 00)
Level 2 falling (LVWV = 01)
Level 3 falling (LVWV = 10)
Level 4 falling (LVWV = 11)
1.74
1.84
1.94
2.04
1.80
1.90
2.00
2.10
1.86
1.96
2.06
2.16
V
V
V
V
1
VHYSL Low-voltage inhibit reset/recover hysteresis —
low range
±40 mV
VBG Bandgap voltage reference 0.97 1.00 1.03 V
tLPO Internal low power oscillator period — factory
trimmed
900 1000 1100 μs
1. Rising thresholds are falling threshold + hysteresis voltage
2.2.3 Voltage and current operating behaviors
Table 7. Voltage and current operating behaviors
Symbol Description Min. Max. Unit Notes
VOH Output high voltage — Normal drive pad (except
RESET)
2.7 V ≤ VDD ≤ 3.6 V, IOH = –5 mA
1.71 V ≤ VDD ≤ 2.7 V, IOH = –1.5 mA
VDD – 0.5
VDD – 0.5
V
V
1, 2
VOH Output high voltage — High drive pad (except
RESET)
2.7 V ≤ VDD ≤ 3.6 V, IOH = –18 mA
1.71 V ≤ VDD ≤ 2.7 V, IOH = –6 mA
VDD – 0.5
VDD – 0.5
V
V
1, 2
IOHT Output high current total for all ports 100 mA
Table continues on the next page...
General
8Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Table 7. Voltage and current operating behaviors (continued)
Symbol Description Min. Max. Unit Notes
VOL Output low voltage — Normal drive pad
2.7 V ≤ VDD ≤ 3.6 V, IOL = 5 mA
1.71 V ≤ VDD ≤ 2.7 V, IOL = 1.5 mA
0.5
0.5
V
V
1
VOL Output low voltage — High drive pad
2.7 V ≤ VDD ≤ 3.6 V, IOL = 18 mA
1.71 V ≤ VDD ≤ 2.7 V, IOL = 6 mA
0.5
0.5
V
V
1
IOLT Output low current total for all ports 100 mA
IIN Input leakage current (per pin) for full temperature
range
1 μA 3
IIN Input leakage current (per pin) at 25 °C 0.025 μA 3
IIN Input leakage current (total all pins) for full
temperature range
65 μA 3
IOZ Hi-Z (off-state) leakage current (per pin) 1 μA
RPU Internal pullup resistors 20 50 4
RPD Internal pulldown resistors 20 50 5
1. PTB0, PTB1, PTD6, and PTD7 I/O have both high drive and normal drive capability selected by the associated
PTx_PCRn[DSE] control bit. All other GPIOs are normal drive only.
2. The reset pin only contains an active pull down device when configured as the RESET signal or as a GPIO. When
configured as a GPIO output, it acts as a pseudo open drain output.
3. Measured at VDD = 3.6 V
4. Measured at VDD supply voltage = VDD min and Vinput = VSS
5. Measured at VDD supply voltage = VDD min and Vinput = VDD
2.2.4 Power mode transition operating behaviors
All specifications except tPOR and VLLSxRUN recovery times in the following
table assume this clock configuration:
CPU and system clocks = 48 MHz
Bus and flash clock = 24 MHz
FEI clock mode
POR and VLLSxRUN recovery use FEI clock mode at the default CPU and system
frequency of 21 MHz, and a bus and flash clock frequency of 10.5 MHz.
Table 8. Power mode transition operating behaviors
Symbol Description Min. Typ. Max. Unit
tPOR After a POR event, amount of time from the
point VDD reaches 1.8 V to execution of the first
300 μs 1
Table continues on the next page...
General
Kinetis KL25 Sub-Family, Rev5 08/2014. 9
Freescale Semiconductor, Inc.
Table 8. Power mode transition operating behaviors (continued)
Symbol Description Min. Typ. Max. Unit
instruction across the operating temperature
range of the chip.
VLLS0 RUN
95
115
μs
VLLS1 RUN
93
115
μs
VLLS3 RUN
42
53
μs
LLS RUN
4
4.6
μs
VLPS RUN
4
4.4
μs
STOP RUN
4
4.4
μs
1. Normal boot (FTFA_FOPT[LPBOOT]=11).
2.2.5 Power consumption operating behaviors
The maximum values stated in the following table represent characterized results
equivalent to the mean plus three times the standard deviation (mean + 3 sigma).
Table 9. Power consumption operating behaviors
Symbol Description Temp. Typ. Max Unit Note
IDDA Analog supply current See note mA 1
IDD_RUNCO_ CM Run mode current in compute operation
- 48 MHz core / 24 MHz flash/ bus
disabled, LPTMR running using 4 MHz
internal reference clock, CoreMark®
benchmark code executing from flash,
at 3.0 V
6.4 mA 2
IDD_RUNCO Run mode current in compute operation
- 48 MHz core / 24 MHz flash / bus
clock disabled, code of while(1) loop
executing from flash, at 3.0 V
3.9 4.8 mA 3
IDD_RUN Run mode current - 48 MHz core / 24
MHz bus and flash, all peripheral clocks
disabled, code executing from flash, at
3.0 V
5 5.9 mA 3
Table continues on the next page...
General
10 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Table 9. Power consumption operating behaviors (continued)
Symbol Description Temp. Typ. Max Unit Note
IDD_RUN Run mode current - 48 MHz core / 24
MHz bus and flash, all peripheral clocks
enabled, code executing from flash, at
3.0 V
at 25 °C 6.2 6.5 mA 3, 4
at 125 °C 6.8 7.1 mA
IDD_WAIT Wait mode current - core disabled / 48
MHz system / 24 MHz bus / flash
disabled (flash doze enabled), all
peripheral clocks disabled, at 3.0 V
3.1 3.8 mA 3
IDD_WAIT Wait mode current - core disabled / 24
MHz system / 24 MHz bus / flash
disabled (flash doze enabled), all
peripheral clocks disabled • at 3.0 V
2.4 3.2 mA 3
IDD_PSTOP2 Stop mode current with partial stop 2
clocking option - core and system
disabled / 10.5 MHz bus, at 3.0 V
1.6 2 mA 3
IDD_VLPRCO _CM Very-low-power run mode current in
compute operation - 4 MHz core / 0.8
MHz flash / bus clock disabled, LPTMR
running with 4 MHz internal reference
clock, CoreMark benchmark code
executing from flash, at 3.0 V
777 µA 5
IDD_VLPRCO Very low power run mode current in
compute operation - 4 MHz core / 0.8
MHz flash / bus clock disabled, code
executing from flash, at 3.0 V
171 420 µA 6
IDD_VLPR Very low power run mode current - 4
MHz core / 0.8 MHz bus and flash, all
peripheral clocks disabled, code
executing from flash, at 3.0 V
204 449 µA 6
IDD_VLPR Very low power run mode current - 4
MHz core / 0.8 MHz bus and flash, all
peripheral clocks enabled, code
executing from flash, at 3.0 V
262 509 µA 4, 6
IDD_VLPW Very low power wait mode current -
core disabled / 4 MHz system / 0.8
MHz bus / flash disabled (flash doze
enabled), all peripheral clocks disabled,
at 3.0 V
123 366 µA 6
IDD_STOP Stop mode current at 3.0 V at 25 °C 319 343 µA
at 50 °C 333 365 µA
at 70 °C 353 400 µA
at 85 °C 380 450 µA
at 105 °C 444 572 µA
IDD_VLPS Very-low-power stop mode current at
3.0 V
at 25 °C 3.75 8.46 µA
at 50 °C 6.66 13.41 µA
at 70 °C 12.9 25.71 µA
Table continues on the next page...
General
Kinetis KL25 Sub-Family, Rev5 08/2014. 11
Freescale Semiconductor, Inc.
Table 9. Power consumption operating behaviors (continued)
Symbol Description Temp. Typ. Max Unit Note
at 85 °C 22.7 44.06 µA
at 105 °C 48.4 90.1 µA
IDD_LLS Low leakage stop mode current at 3.0
V
at 25 °C 1.68 2.09 µA
at 50 °C 3.05 4.04 µA
at 70 °C 5.71 7.75 µA
at 85 °C 10 13.54 µA
at 105 °C 22.4 30.41 µA
IDD_VLLS3 Very low-leakage stop mode 3 current
at 3.0 V
at 25 °C 1.22 1.6 µA
at 50 °C 2.25 2.31 µA
at 70 °C 4.21 5.44 µA
at 85 °C 7.37 9.44 µA
at 105 °C 16.6 21.76 µA
IDD_VLLS1 Very low-leakage stop mode 1 current
at 3.0 V
at 25 °C 0.58 0.94 µA
at 50 °C 1.26 1.31 µA
at 70 °C 2.53 3.33 µA
at 85 °C 4.74 6.1 µA
at 105 °C 11.4 15.27 µA
IDD_VLLS0 Very low-leakage stop mode 0 current
(SMC_STOPCTRL[PORPO] = 0) at 3.0
V
at 25 °C 0.31 0.65 µA
at 50 °C 0.99 1.43 µA
at 70 °C 2.25 3.01 µA
at 85 °C 4.46 5.83 µA
at 105 °C 11.13 14.99 µA
IDD_VLLS0 Very low-leakage stop mode 0 current
(SMC_STOPCTRL[PORPO] = 1) at 3.0
V
at 25 °C 0.12 0.47 µA 7
at 50 °C 0.8 1.24 µA
at 70 °C 2.06 2.81 µA
at 85 °C 4.27 5.62 µA
at 105 °C 10.93 14.78 µA
1. The analog supply current is the sum of the active or disabled current for each of the analog modules on the device. See
each module's specification for its supply current.
2. MCG configured for PEE mode. CoreMark benchmark compiled using Keil 4.54 with optimization level 3, optimized for
time.
3. MCG configured for FEI mode.
4. Incremental current consumption from peripheral activity is not included.
5. MCG configured for BLPI mode. CoreMark benchmark compiled using IAR 6.40 with optimization level high, optimized
for balanced.
6. MCG configured for BLPI mode.
7. No brownout.
General
12 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Table 10. Low power mode peripheral adders — typical value
Symbol Description Temperature (°C) Unit
-40 25 50 70 85 105
IIREFSTEN4MHz 4 MHz internal reference clock (IRC) adder.
Measured by entering STOP or VLPS mode
with 4 MHz IRC enabled.
56 56 56 56 56 56 µA
IIREFSTEN32KHz 32 kHz internal reference clock (IRC) adder.
Measured by entering STOP mode with the
32 kHz IRC enabled.
52 52 52 52 52 52 µA
IEREFSTEN4MHz External 4 MHz crystal clock adder.
Measured by entering STOP or VLPS mode
with the crystal enabled.
206 228 237 245 251 258 µA
IEREFSTEN32KHz External 32 kHz crystal clock
adder by means of the
OSC0_CR[EREFSTEN and
EREFSTEN] bits. Measured
by entering all modes with
the crystal enabled.
VLLS1 440 490 540 560 570 580 nA
VLLS3 440 490 540 560 570 580
LLS 490 490 540 560 570 680
VLPS 510 560 560 560 610 680
STOP 510 560 560 560 610 680
ICMP CMP peripheral adder measured by placing
the device in VLLS1 mode with CMP
enabled using the 6-bit DAC and a single
external input for compare. Includes 6-bit
DAC power consumption.
22 22 22 22 22 22 µA
IRTC RTC peripheral adder measured by placing
the device in VLLS1 mode with external 32
kHz crystal enabled by means of the
RTC_CR[OSCE] bit and the RTC ALARM
set for 1 minute. Includes ERCLK32K (32
kHz external crystal) power consumption.
432 357 388 475 532 810 nA
IUART UART peripheral adder
measured by placing the
device in STOP or VLPS
mode with selected clock
source waiting for RX data at
115200 baud rate. Includes
selected clock source power
consumption.
MCGIRCLK
(4 MHz
internal
reference
clock)
66 66 66 66 66 66 µA
OSCERCLK
(4 MHz
external
crystal)
214 237 246 254 260 268
ITPM TPM peripheral adder
measured by placing the
device in STOP or VLPS
mode with selected clock
source configured for output
compare generating 100 Hz
clock signal. No load is
placed on the I/O generating
the clock signal. Includes
selected clock source and
I/O switching currents.
MCGIRCLK
(4 MHz
internal
reference
clock)
86 86 86 86 86 86 µA
OSCERCLK
(4 MHz
external
crystal)
235 256 265 274 280 287
Table continues on the next page...
General
Kinetis KL25 Sub-Family, Rev5 08/2014. 13
Freescale Semiconductor, Inc.
Table 10. Low power mode peripheral adders — typical value (continued)
Symbol Description Temperature (°C) Unit
-40 25 50 70 85 105
IBG Bandgap adder when BGEN bit is set and
device is placed in VLPx, LLS, or VLLSx
mode.
45 45 45 45 45 45 µA
IADC ADC peripheral adder combining the
measured values at VDD and VDDA by
placing the device in STOP or VLPS mode.
ADC is configured for low power mode using
the internal clock and continuous
conversions.
366 366 366 366 366 366 µA
2.2.5.1 Diagram: Typical IDD_RUN operating behavior
The following data was measured under these conditions:
MCG in FBE for run mode, and BLPE for VLPR mode
USB regulator disabled
No GPIOs toggled
Code execution from flash with cache enabled
For the ALLOFF curve, all peripheral clocks are disabled except FTFA
General
14 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
All Off
Temperature = 25, V = 3, CACHE = Enable, Code Residence = Flash, Clocking Mode = FBE
DD
All Peripheral CLK Gates
All On
CLK Ratio
Flash-Core
Core Freq (MHz)
Current Consumption on VDD(A)
Run Mode Current Vs Core Frequency
8.00E-03
7.00E-03
6.00E-03
5.00E-03
4.00E-03
3.00E-03
2.00E-03
1.00E-03
000.00E+00
'1-1
1 2 34612 24 48
'1-1 '1-1 '1-1 '1-1 '1-1 '1-1 '1-2
Figure 3. Run mode supply current vs. core frequency
General
Kinetis KL25 Sub-Family, Rev5 08/2014. 15
Freescale Semiconductor, Inc.
VLPR Mode Current Vs Core Frequency
Temperature = 25, V = 3, CACHE = Enable, Code Residence = Flash, Clocking Mode = BLPE
DD
All Peripheral CLK Gates
'1
-
1
'1
-
2
'1
-
2
'1
-
4
All Off
All On
CLK Ratio
Flash-Core
Core Freq (MHz)
Current Consumption on VDD (A)
400.00E-06
350.00E-06
300.00E-06
250.00E-06
200.00E-06
150.00E-06
100.00E-06
50.00E-06
000.00E+00
1 2 4
Figure 4. VLPR mode current vs. core frequency
2.2.6 EMC radiated emissions operating behaviors
Table 11. EMC radiated emissions operating behaviors for 64-pin LQFP
package
Symbol Description Frequency
band
(MHz)
Typ. Unit Notes
VRE1 Radiated emissions voltage, band 1 0.15–50 13 dBμV 1, 2
VRE2 Radiated emissions voltage, band 2 50–150 15 dBμV
VRE3 Radiated emissions voltage, band 3 150–500 12 dBμV
VRE4 Radiated emissions voltage, band 4 500–1000 7 dBμV
VRE_IEC IEC level 0.15–1000 M 2, 3
1. Determined according to IEC Standard 61967-1, Integrated Circuits - Measurement of Electromagnetic Emissions, 150
kHz to 1 GHz Part 1: General Conditions and Definitions and IEC Standard 61967-2, Integrated Circuits - Measurement
of Electromagnetic Emissions, 150 kHz to 1 GHz Part 2: Measurement of Radiated Emissions—TEM Cell and
General
16 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Wideband TEM Cell Method. Measurements were made while the microcontroller was running basic application code.
The reported emission level is the value of the maximum measured emission, rounded up to the next whole number,
from among the measured orientations in each frequency range.
2. VDD = 3.3 V, TA = 25 °C, fOSC = 8 MHz (crystal), fSYS = 48 MHz, fBUS = 48 MHz
3. Specified according to Annex D of IEC Standard 61967-2, Measurement of Radiated Emissions—TEM Cell and
Wideband TEM Cell Method
2.2.7 Designing with radiated emissions in mind
To find application notes that provide guidance on designing your system to minimize
interference from radiated emissions:
1. Go to www.freescale.com.
2. Perform a keyword search for “EMC design.”
2.2.8 Capacitance attributes
Table 12. Capacitance attributes
Symbol Description Min. Max. Unit
CIN Input capacitance 7 pF
2.3 Switching specifications
2.3.1 Device clock specifications
Table 13. Device clock specifications
Symbol Description Min. Max. Unit
Normal run mode
fSYS System and core clock 48 MHz
fBUS Bus clock 24 MHz
fFLASH Flash clock 24 MHz
fSYS_USB System and core clock when Full Speed USB in operation 20 MHz
fLPTMR LPTMR clock 24 MHz
VLPR and VLPS modes1
fSYS System and core clock 4 MHz
fBUS Bus clock 1 MHz
fFLASH Flash clock 1 MHz
fLPTMR LPTMR clock2 24 MHz
Table continues on the next page...
General
Kinetis KL25 Sub-Family, Rev5 08/2014. 17
Freescale Semiconductor, Inc.
Table 13. Device clock specifications (continued)
Symbol Description Min. Max. Unit
fERCLK External reference clock 16 MHz
fLPTMR_ERCLK LPTMR external reference clock 16 MHz
fosc_hi_2 Oscillator crystal or resonator frequency — high frequency
mode (high range) (MCG_C2[RANGE]=1x)
16 MHz
fTPM TPM asynchronous clock 8 MHz
fUART0 UART0 asynchronous clock 8 MHz
1. The frequency limitations in VLPR and VLPS modes here override any frequency specification listed in the timing
specification for any other module. These same frequency limits apply to VLPS, whether VLPS was entered from RUN
or from VLPR.
2. The LPTMR can be clocked at this speed in VLPR or VLPS only when the source is an external pin.
2.3.2 General switching specifications
These general-purpose specifications apply to all signals configured for GPIO and
UART signals.
Table 14. General switching specifications
Description Min. Max. Unit Notes
GPIO pin interrupt pulse width (digital glitch filter disabled) —
Synchronous path
1.5 Bus clock
cycles
1
External RESET and NMI pin interrupt pulse width —
Asynchronous path
100 ns 2
GPIO pin interrupt pulse width — Asynchronous path 16 ns 2
Port rise and fall time 36 ns 3
1. The greater synchronous and asynchronous timing must be met.
2. This is the shortest pulse that is guaranteed to be recognized.
3. 75 pF load
2.4 Thermal specifications
2.4.1 Thermal operating requirements
Table 15. Thermal operating requirements
Symbol Description Min. Max. Unit
TJDie junction temperature –40 125 °C
TAAmbient temperature –40 105 °C
General
18 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
2.4.2 Thermal attributes
Table 16. Thermal attributes
Board type Symbol Description 80
LQFP
64
LQFP
48 QFN 32 QFN Unit Notes
Single-layer (1S) RθJA Thermal resistance, junction
to ambient (natural
convection)
70 71 84 92 °C/W 1
Four-layer (2s2p) RθJA Thermal resistance, junction
to ambient (natural
convection)
53 52 28 33 °C/W
Single-layer (1S) RθJMA Thermal resistance, junction
to ambient (200 ft./min. air
speed)
59 69 75 °C/W
Four-layer (2s2p) RθJMA Thermal resistance, junction
to ambient (200 ft./min. air
speed)
46 22 27 °C/W
RθJB Thermal resistance, junction
to board
34 34 10 12 °C/W 2
RθJC Thermal resistance, junction
to case
15 20 2.0 1.8 °C/W 3
ΨJT Thermal characterization
parameter, junction to
package top outside center
(natural convection)
0.6 5 5.0 8 °C/W 4
1. Determined according to JEDEC Standard JESD51-2, Integrated Circuits Thermal Test Method Environmental
Conditions—Natural Convection (Still Air), or EIA/JEDEC Standard JESD51-6, Integrated Circuit Thermal Test
Method Environmental Conditions—Forced Convection (Moving Air).
2. Determined according to JEDEC Standard JESD51-8, Integrated Circuit Thermal Test Method Environmental
Conditions—Junction-to-Board.
3. Determined according to Method 1012.1 of MIL-STD 883, Test Method Standard, Microcircuits, with the cold plate
temperature used for the case temperature. The value includes the thermal resistance of the interface material
between the top of the package and the cold plate.
4. Determined according to JEDEC Standard JESD51-2, Integrated Circuits Thermal Test Method Environmental
Conditions—Natural Convection (Still Air).
3 Peripheral operating requirements and behaviors
3.1 Core modules
Peripheral operating requirements and behaviors
Kinetis KL25 Sub-Family, Rev5 08/2014. 19
Freescale Semiconductor, Inc.
3.1.1 SWD electricals
Table 17. SWD full voltage range electricals
Symbol Description Min. Max. Unit
Operating voltage 1.71 3.6 V
J1 SWD_CLK frequency of operation
Serial wire debug
0
25
MHz
J2 SWD_CLK cycle period 1/J1 ns
J3 SWD_CLK clock pulse width
Serial wire debug
20
ns
J4 SWD_CLK rise and fall times 3 ns
J9 SWD_DIO input data setup time to SWD_CLK rise 10 ns
J10 SWD_DIO input data hold time after SWD_CLK rise 0 ns
J11 SWD_CLK high to SWD_DIO data valid 32 ns
J12 SWD_CLK high to SWD_DIO high-Z 5 ns
J2
J3 J3
J4 J4
SWD_CLK (input)
Figure 5. Serial wire clock input timing
Peripheral operating requirements and behaviors
20 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Figure 6. Serial wire data timing
3.2 System modules
There are no specifications necessary for the device's system modules.
3.3 Clock modules
3.3.1 MCG specifications
Table 18. MCG specifications
Symbol Description Min. Typ. Max. Unit Notes
fints_ft Internal reference frequency (slow clock) —
factory trimmed at nominal VDD and 25 °C
32.768 kHz
fints_t Internal reference frequency (slow clock) —
user trimmed
31.25 39.0625 kHz
Δfdco_res_t Resolution of trimmed average DCO output
frequency at fixed voltage and temperature —
using C3[SCTRIM] and C4[SCFTRIM]
± 0.3 ± 0.6 %fdco 1
Table continues on the next page...
Peripheral operating requirements and behaviors
Kinetis KL25 Sub-Family, Rev5 08/2014. 21
Freescale Semiconductor, Inc.
Table 18. MCG specifications (continued)
Symbol Description Min. Typ. Max. Unit Notes
Δfdco_t Total deviation of trimmed average DCO output
frequency over voltage and temperature
+0.5/-0.7 ± 3 %fdco 1, 2
Δfdco_t Total deviation of trimmed average DCO output
frequency over fixed voltage and temperature
range of 0–70 °C
± 0.4 ± 1.5 %fdco 1, 2
fintf_ft Internal reference frequency (fast clock) —
factory trimmed at nominal VDD and 25 °C
4 MHz
Δfintf_ft Frequency deviation of internal reference clock
(fast clock) over temperature and voltage —
factory trimmed at nominal VDD and 25 °C
+1/-2 ± 3 %fintf_ft 2
fintf_t Internal reference frequency (fast clock) —
user trimmed at nominal VDD and 25 °C
3 5 MHz
floc_low Loss of external clock minimum frequency —
RANGE = 00
(3/5) x
fints_t
kHz
floc_high Loss of external clock minimum frequency —
RANGE = 01, 10, or 11
(16/5) x
fints_t
kHz
FLL
ffll_ref FLL reference frequency range 31.25 39.0625 kHz
fdco DCO output
frequency range
Low range (DRS = 00)
640 × ffll_ref
20 20.97 25 MHz 3, 4
Mid range (DRS = 01)
1280 × ffll_ref
40 41.94 48 MHz
fdco_t_DMX3
2
DCO output
frequency
Low range (DRS = 00)
732 × ffll_ref
23.99 MHz 5, 6
Mid range (DRS = 01)
1464 × ffll_ref
47.97 MHz
Jcyc_fll FLL period jitter
fVCO = 48 MHz
180 ps 7
tfll_acquire FLL target frequency acquisition time 1 ms 8
PLL
fvco VCO operating frequency 48.0 100 MHz
Ipll PLL operating current
PLL at 96 MHz (fosc_hi_1 = 8 MHz, fpll_ref =
2 MHz, VDIV multiplier = 48)
1060 µA 9
Ipll PLL operating current
PLL at 48 MHz (fosc_hi_1 = 8 MHz, fpll_ref =
2 MHz, VDIV multiplier = 24)
600 µA 9
fpll_ref PLL reference frequency range 2.0 4.0 MHz
Jcyc_pll PLL period jitter (RMS)
fvco = 48 MHz
fvco = 100 MHz
120
50
ps
ps
10
Table continues on the next page...
Peripheral operating requirements and behaviors
22 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Table 18. MCG specifications (continued)
Symbol Description Min. Typ. Max. Unit Notes
Jacc_pll PLL accumulated jitter over 1µs (RMS)
fvco = 48 MHz
fvco = 100 MHz
1350
600
ps
ps
10
Dlock Lock entry frequency tolerance ± 1.49 ± 2.98 %
Dunl Lock exit frequency tolerance ± 4.47 ± 5.97 %
tpll_lock Lock detector detection time 150 × 10-6
+ 1075(1/
fpll_ref)
s11
1. This parameter is measured with the internal reference (slow clock) being used as a reference to the FLL (FEI clock
mode).
2. The deviation is relative to the factory trimmed frequency at nominal VDD and 25 °C, fints_ft.
3. These typical values listed are with the slow internal reference clock (FEI) using factory trim and DMX32 = 0.
4. The resulting system clock frequencies must not exceed their maximum specified values. The DCO frequency
deviation (Δfdco_t) over voltage and temperature must be considered.
5. These typical values listed are with the slow internal reference clock (FEI) using factory trim and DMX32 = 1.
6. The resulting clock frequency must not exceed the maximum specified clock frequency of the device.
7. This specification is based on standard deviation (RMS) of period or frequency.
8. This specification applies to any time the FLL reference source or reference divider is changed, trim value is changed,
DMX32 bit is changed, DRS bits are changed, or changing from FLL disabled (BLPE, BLPI) to FLL enabled (FEI, FEE,
FBE, FBI). If a crystal/resonator is being used as the reference, this specification assumes it is already running.
9. Excludes any oscillator currents that are also consuming power while PLL is in operation.
10. This specification was obtained using a Freescale developed PCB. PLL jitter is dependent on the noise
characteristics of each PCB and results will vary.
11. This specification applies to any time the PLL VCO divider or reference divider is changed, or changing from PLL
disabled (BLPE, BLPI) to PLL enabled (PBE, PEE). If a crystal/resonator is being used as the reference, this
specification assumes it is already running.
3.3.2 Oscillator electrical specifications
3.3.2.1 Oscillator DC electrical specifications
Table 19. Oscillator DC electrical specifications
Symbol Description Min. Typ. Max. Unit Notes
VDD Supply voltage 1.71 3.6 V
IDDOSC Supply current — low-power mode (HGO=0)
32 kHz
4 MHz
8 MHz (RANGE=01)
16 MHz
500
200
300
950
1.2
nA
μA
μA
μA
mA
1
Table continues on the next page...
Peripheral operating requirements and behaviors
Kinetis KL25 Sub-Family, Rev5 08/2014. 23
Freescale Semiconductor, Inc.
Table 19. Oscillator DC electrical specifications (continued)
Symbol Description Min. Typ. Max. Unit Notes
24 MHz
32 MHz
1.5 mA
IDDOSC Supply current — high gain mode (HGO=1)
32 kHz
4 MHz
8 MHz (RANGE=01)
16 MHz
24 MHz
32 MHz
25
400
500
2.5
3
4
μA
μA
μA
mA
mA
mA
1
CxEXTAL load capacitance 2, 3
CyXTAL load capacitance 2, 3
RFFeedback resistor — low-frequency, low-power
mode (HGO=0)
2, 4
Feedback resistor — low-frequency, high-gain
mode (HGO=1)
10
Feedback resistor — high-frequency, low-
power mode (HGO=0)
Feedback resistor — high-frequency, high-gain
mode (HGO=1)
1
RSSeries resistor — low-frequency, low-power
mode (HGO=0)
Series resistor — low-frequency, high-gain
mode (HGO=1)
200
Series resistor — high-frequency, low-power
mode (HGO=0)
Series resistor — high-frequency, high-gain
mode (HGO=1)
0
Vpp5Peak-to-peak amplitude of oscillation (oscillator
mode) — low-frequency, low-power mode
(HGO=0)
0.6 V
Peak-to-peak amplitude of oscillation (oscillator
mode) — low-frequency, high-gain mode
(HGO=1)
VDD V
Peak-to-peak amplitude of oscillation (oscillator
mode) — high-frequency, low-power mode
(HGO=0)
0.6 V
Peak-to-peak amplitude of oscillation (oscillator
mode) — high-frequency, high-gain mode
(HGO=1)
VDD V
1. VDD=3.3 V, Temperature =25 °C
2. See crystal or resonator manufacturer's recommendation
Peripheral operating requirements and behaviors
24 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
3. Cx,Cy can be provided by using the integrated capacitors when the low frequency oscillator (RANGE = 00) is used. For
all other cases external capacitors must be used.
4. When low power mode is selected, RF is integrated and must not be attached externally.
5. The EXTAL and XTAL pins should only be connected to required oscillator components and must not be connected to
any other devices.
3.3.2.2 Oscillator frequency specifications
Table 20. Oscillator frequency specifications
Symbol Description Min. Typ. Max. Unit Notes
fosc_lo Oscillator crystal or resonator frequency — low-
frequency mode (MCG_C2[RANGE]=00)
32 40 kHz
fosc_hi_1 Oscillator crystal or resonator frequency —
high-frequency mode (low range)
(MCG_C2[RANGE]=01)
3 8 MHz
fosc_hi_2 Oscillator crystal or resonator frequency —
high frequency mode (high range)
(MCG_C2[RANGE]=1x)
8 32 MHz
fec_extal Input clock frequency (external clock mode) 48 MHz 1, 2
tdc_extal Input clock duty cycle (external clock mode) 40 50 60 %
tcst Crystal startup time — 32 kHz low-frequency,
low-power mode (HGO=0)
750 ms 3, 4
Crystal startup time — 32 kHz low-frequency,
high-gain mode (HGO=1)
250 ms
Crystal startup time — 8 MHz high-frequency
(MCG_C2[RANGE]=01), low-power mode
(HGO=0)
0.6 ms
Crystal startup time — 8 MHz high-frequency
(MCG_C2[RANGE]=01), high-gain mode
(HGO=1)
1 ms
1. Other frequency limits may apply when external clock is being used as a reference for the FLL or PLL.
2. When transitioning from FEI or FBI to FBE mode, restrict the frequency of the input clock so that, when it is divided by
FRDIV, it remains within the limits of the DCO input clock frequency.
3. Proper PC board layout procedures must be followed to achieve specifications.
4. Crystal startup time is defined as the time between the oscillator being enabled and the OSCINIT bit in the MCG_S
register being set.
3.4 Memories and memory interfaces
3.4.1 Flash electrical specifications
This section describes the electrical characteristics of the flash memory module.
Peripheral operating requirements and behaviors
Kinetis KL25 Sub-Family, Rev5 08/2014. 25
Freescale Semiconductor, Inc.
3.4.1.1 Flash timing specifications — program and erase
The following specifications represent the amount of time the internal charge pumps are
active and do not include command overhead.
Table 21. NVM program/erase timing specifications
Symbol Description Min. Typ. Max. Unit Notes
thvpgm4 Longword Program high-voltage time 7.5 18 μs
thversscr Sector Erase high-voltage time 13 113 ms 1
thversall Erase All high-voltage time 52 452 ms 1
1. Maximum time based on expectations at cycling end-of-life.
3.4.1.2 Flash timing specifications — commands
Table 22. Flash command timing specifications
Symbol Description Min. Typ. Max. Unit Notes
trd1sec1k Read 1s Section execution time (flash sector) 60 μs 1
tpgmchk Program Check execution time 45 μs 1
trdrsrc Read Resource execution time 30 μs 1
tpgm4 Program Longword execution time 65 145 μs
tersscr Erase Flash Sector execution time 14 114 ms 2
trd1all Read 1s All Blocks execution time 1.8 ms
trdonce Read Once execution time 25 μs 1
tpgmonce Program Once execution time 65 μs
tersall Erase All Blocks execution time 88 650 ms 2
tvfykey Verify Backdoor Access Key execution time 30 μs 1
1. Assumes 25 MHz flash clock frequency.
2. Maximum times for erase parameters based on expectations at cycling end-of-life.
3.4.1.3 Flash high voltage current behaviors
Table 23. Flash high voltage current behaviors
Symbol Description Min. Typ. Max. Unit
IDD_PGM Average current adder during high voltage
flash programming operation
2.5 6.0 mA
IDD_ERS Average current adder during high voltage
flash erase operation
1.5 4.0 mA
Peripheral operating requirements and behaviors
26 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
3.4.1.4 Reliability specifications
Table 24. NVM reliability specifications
Symbol Description Min. Typ.1Max. Unit Notes
Program Flash
tnvmretp10k Data retention after up to 10 K cycles 5 50 years
tnvmretp1k Data retention after up to 1 K cycles 20 100 years
nnvmcycp Cycling endurance 10 K 50 K cycles 2
1. Typical data retention values are based on measured response accelerated at high temperature and derated to a
constant 25 °C use profile. Engineering Bulletin EB618 does not apply to this technology. Typical endurance defined in
Engineering Bulletin EB619.
2. Cycling endurance represents number of program/erase cycles at -40 °C ≤ Tj ≤ 125 °C.
3.5 Security and integrity modules
There are no specifications necessary for the device's security and integrity modules.
3.6 Analog
3.6.1 ADC electrical specifications
The 16-bit accuracy specifications listed in Table 25 and Table 26 are achievable on
the differential pins ADCx_DP0, ADCx_DM0.
All other ADC channels meet the 13-bit differential/12-bit single-ended accuracy
specifications.
3.6.1.1 16-bit ADC operating conditions
Table 25. 16-bit ADC operating conditions
Symbol Description Conditions Min. Typ.1Max. Unit Notes
VDDA Supply voltage Absolute 1.71 3.6 V
ΔVDDA Supply voltage Delta to VDD (VDD – VDDA) -100 0 +100 mV 2
ΔVSSA Ground voltage Delta to VSS (VSS – VSSA) -100 0 +100 mV 2
VREFH ADC reference
voltage high
1.13 VDDA VDDA V3
VREFL ADC reference
voltage low
VSSA VSSA VSSA V3
Table continues on the next page...
Peripheral operating requirements and behaviors
Kinetis KL25 Sub-Family, Rev5 08/2014. 27
Freescale Semiconductor, Inc.
Table 25. 16-bit ADC operating conditions (continued)
Symbol Description Conditions Min. Typ.1Max. Unit Notes
VADIN Input voltage 16-bit differential mode
All other modes
VREFL
VREFL
31/32 *
VREFH
VREFH
V
CADIN Input
capacitance
16-bit mode
8-bit / 10-bit / 12-bit
modes
8
4
10
5
pF
RADIN Input series
resistance
2 5
RAS Analog source
resistance
(external)
13-bit / 12-bit modes
fADCK < 4 MHz
5
4
fADCK ADC conversion
clock frequency
≤ 13-bit mode 1.0 18.0 MHz 5
fADCK ADC conversion
clock frequency
16-bit mode 2.0 12.0 MHz 5
Crate ADC conversion
rate
≤ 13-bit modes
No ADC hardware averaging
Continuous conversions
enabled, subsequent
conversion time
20.000
818.330
Ksps
6
Crate ADC conversion
rate
16-bit mode
No ADC hardware averaging
Continuous conversions
enabled, subsequent
conversion time
37.037
461.467
Ksps
6
1. Typical values assume VDDA = 3.0 V, Temp = 25 °C, fADCK = 1.0 MHz, unless otherwise stated. Typical values are for
reference only, and are not tested in production.
2. DC potential difference.
3. For packages without dedicated VREFH and VREFL pins, VREFH is internally tied to VDDA, and VREFL is internally tied to
VSSA.
4. This resistance is external to MCU. To achieve the best results, the analog source resistance must be kept as low as
possible. The results in this data sheet were derived from a system that had < 8 Ω analog source resistance. The
RAS/CAS time constant should be kept to < 1 ns.
5. To use the maximum ADC conversion clock frequency, CFG2[ADHSC] must be set and CFG1[ADLPC] must be clear.
6. For guidelines and examples of conversion rate calculation, download the ADC calculator tool.
Peripheral operating requirements and behaviors
28 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
RAS
VAS CAS
ZAS
VADIN
ZADIN
RADIN
RADIN
RADIN
RADIN
CADIN
Pad
leakage
due to
input
protection
INPUT PIN
INPUT PIN
INPUT PIN
SIMPLIFIED
INPUT PIN EQUIVALENT
CIRCUIT
SIMPLIFIED
CHANNEL SELECT
CIRCUIT
ADC SAR
ENGINE
Figure 7. ADC input impedance equivalency diagram
3.6.1.2 16-bit ADC electrical characteristics
Table 26. 16-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA)
Symbol Description Conditions1Min. Typ.2Max. Unit Notes
IDDA_ADC Supply current 0.215 1.7 mA 3
fADACK
ADC
asynchronous
clock source
ADLPC = 1, ADHSC =
0
ADLPC = 1, ADHSC =
1
ADLPC = 0, ADHSC =
0
ADLPC = 0, ADHSC =
1
1.2
2.4
3.0
4.4
2.4
4.0
5.2
6.2
3.9
6.1
7.3
9.5
MHz
MHz
MHz
MHz
tADACK =
1/fADACK
Sample Time See Reference Manual chapter for sample times
TUE Total unadjusted
error
12-bit modes
<12-bit modes
±4
±1.4
±6.8
±2.1
LSB45
DNL Differential non-
linearity
12-bit modes
<12-bit modes
±0.7
±0.2
–1.1 to
+1.9
–0.3 to 0.5
LSB45
Table continues on the next page...
Peripheral operating requirements and behaviors
Kinetis KL25 Sub-Family, Rev5 08/2014. 29
Freescale Semiconductor, Inc.
Table 26. 16-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA) (continued)
Symbol Description Conditions1Min. Typ.2Max. Unit Notes
INL Integral non-
linearity
12-bit modes
<12-bit modes
±1.0
±0.5
–2.7 to
+1.9
–0.7 to
+0.5
LSB45
EFS Full-scale error 12-bit modes
<12-bit modes
–4
–1.4
–5.4
–1.8
LSB4VADIN =
VDDA5
EQQuantization
error
16-bit modes
≤13-bit modes
–1 to 0
±0.5
LSB4
ENOB Effective number
of bits
16-bit differential mode
Avg = 32
Avg = 4
16-bit single-ended mode
Avg = 32
Avg = 4
12.8
11.9
12.2
11.4
14.5
13.8
13.9
13.1
bits
bits
bits
bits
6
SINAD Signal-to-noise
plus distortion
See ENOB 6.02 × ENOB + 1.76 dB
THD Total harmonic
distortion
16-bit differential mode
Avg = 32
16-bit single-ended mode
Avg = 32
-94
-85
dB
dB
7
SFDR Spurious free
dynamic range
16-bit differential mode
Avg = 32
16-bit single-ended mode
Avg = 32
82
78
95
90
dB
dB
7
EIL Input leakage
error
IIn × RAS mV IIn =
leakage
current
(refer to
the MCU's
voltage
and
current
operating
ratings)
Temp sensor
slope
Across the full temperature
range of the device
1.55 1.62 1.69 mV/°C 8
VTEMP25 Temp sensor
voltage
25 °C 706 716 726 mV 8
Peripheral operating requirements and behaviors
30 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
1. All accuracy numbers assume the ADC is calibrated with VREFH = VDDA
2. Typical values assume VDDA = 3.0 V, Temp = 25 °C, fADCK = 2.0 MHz unless otherwise stated. Typical values are for
reference only and are not tested in production.
3. The ADC supply current depends on the ADC conversion clock speed, conversion rate and ADC_CFG1[ADLPC] (low
power). For lowest power operation, ADC_CFG1[ADLPC] must be set, the ADC_CFG2[ADHSC] bit must be clear with
1 MHz ADC conversion clock speed.
4. 1 LSB = (VREFH - VREFL)/2N
5. ADC conversion clock < 16 MHz, Max hardware averaging (AVGE = %1, AVGS = %11)
6. Input data is 100 Hz sine wave. ADC conversion clock < 12 MHz.
7. Input data is 1 kHz sine wave. ADC conversion clock < 12 MHz.
8. ADC conversion clock < 3 MHz
Typical ADC 16-bit Differential ENOB vs ADC Clock
100Hz, 90% FS Sine Input
ENOB
ADC Clock Frequency (MHz)
15.00
14.70
14.40
14.10
13.80
13.50
13.20
12.90
12.60
12.30
12.00
1 2 3 4 5 6 7 8 9 10 1211
Hardware Averaging Disabled
Averaging of 4 samples
Averaging of 8 samples
Averaging of 32 samples
Figure 8. Typical ENOB vs. ADC_CLK for 16-bit differential mode
Typical ADC 16-bit Single-Ended ENOB vs ADC Clock
100Hz, 90% FS Sine Input
ENOB
ADC Clock Frequency (MHz)
14.00
13.75
13.25
13.00
12.75
12.50
12.00
11.75
11.50
11.25
11.00
1 2 3 4 5 6 7 8 9 10 1211
Averaging of 4 samples
Averaging of 32 samples
13.50
12.25
Figure 9. Typical ENOB vs. ADC_CLK for 16-bit single-ended mode
Peripheral operating requirements and behaviors
Kinetis KL25 Sub-Family, Rev5 08/2014. 31
Freescale Semiconductor, Inc.
3.6.2 CMP and 6-bit DAC electrical specifications
Table 27. Comparator and 6-bit DAC electrical specifications
Symbol Description Min. Typ. Max. Unit
VDD Supply voltage 1.71 3.6 V
IDDHS Supply current, high-speed mode (EN = 1, PMODE =
1)
200 μA
IDDLS Supply current, low-speed mode (EN = 1, PMODE =
0)
20 μA
VAIN Analog input voltage VSS VDD V
VAIO Analog input offset voltage 20 mV
VHAnalog comparator hysteresis1
CR0[HYSTCTR] = 00
CR0[HYSTCTR] = 01
CR0[HYSTCTR] = 10
CR0[HYSTCTR] = 11
5
10
20
30
mV
mV
mV
mV
VCMPOh Output high VDD – 0.5 V
VCMPOl Output low 0.5 V
tDHS Propagation delay, high-speed mode (EN = 1,
PMODE = 1)
20 50 200 ns
tDLS Propagation delay, low-speed mode (EN = 1, PMODE
= 0)
80 250 600 ns
Analog comparator initialization delay2 40 μs
IDAC6b 6-bit DAC current adder (enabled) 7 μA
INL 6-bit DAC integral non-linearity –0.5 0.5 LSB3
DNL 6-bit DAC differential non-linearity –0.3 0.3 LSB
1. Typical hysteresis is measured with input voltage range limited to 0.7 to VDD – 0.7 V.
2. Comparator initialization delay is defined as the time between software writes to change control inputs (writes to
DACEN, VRSEL, PSEL, MSEL, VOSEL) and the comparator output settling to a stable level.
3. 1 LSB = Vreference/64
Peripheral operating requirements and behaviors
32 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
CMP Hysteresis vs Vinn
0
1
2
HYSTCTR
Setting
000.00E+00
0.1 0.4 0.7 1 1.3 1.6 1.9 2.2 2.5 2.8 3.1
Vinn (V)
3
30.00E-03
20.00E-03
10.00E-03
40.00E-03
50.00E-03
60.00E-03
70.00E-03
80.00E-03
90.00E-03
CMP Hysteresis (V)
Figure 10. Typical hysteresis vs. Vin level (VDD = 3.3 V, PMODE = 0)
180.00E-03
CMP Hysteresis vs Vinn
0
1
2
HYSTCTR
Setting
60.00E-03
0.1 0.4 0.7 1 1.3 1.6 1.9 2.2 2.5 2.8 3.1
CMP Hysteresis (V)
Vinn (V)
3
-20.00E-03
000.00E+00
20.00E-03
40.00E-03
80.00E-03
100.00E-03
120.00E-03
140.00E-03
160.00E-03
Figure 11. Typical hysteresis vs. Vin level (VDD = 3.3 V, PMODE = 1)
3.6.3 12-bit DAC electrical characteristics
Peripheral operating requirements and behaviors
Kinetis KL25 Sub-Family, Rev5 08/2014. 33
Freescale Semiconductor, Inc.
3.6.3.1 12-bit DAC operating requirements
Table 28. 12-bit DAC operating requirements
Symbol Desciption Min. Max. Unit Notes
VDDA Supply voltage 1.71 3.6 V
VDACR Reference voltage 1.13 3.6 V 1
CLOutput load capacitance 100 pF 2
ILOutput load current 1 mA
1. The DAC reference can be selected to be VDDA or VREFH.
2. A small load capacitance (47 pF) can improve the bandwidth performance of the DAC.
3.6.3.2 12-bit DAC operating behaviors
Table 29. 12-bit DAC operating behaviors
Symbol Description Min. Typ. Max. Unit Notes
IDDA_DACL
P
Supply current — low-power mode 250 μA
IDDA_DACH
P
Supply current — high-speed mode 900 μA
tDACLP Full-scale settling time (0x080 to 0xF7F) —
low-power mode
100 200 μs 1
tDACHP Full-scale settling time (0x080 to 0xF7F) —
high-power mode
15 30 μs 1
tCCDACLP Code-to-code settling time (0xBF8 to
0xC08) — low-power mode and high-speed
mode
0.7 1 μs 1
Vdacoutl DAC output voltage range low — high-
speed mode, no load, DAC set to 0x000
100 mV
Vdacouth DAC output voltage range high — high-
speed mode, no load, DAC set to 0xFFF
VDACR
−100
VDACR mV
INL Integral non-linearity error — high speed
mode
±8 LSB 2
DNL Differential non-linearity error — VDACR > 2
V
±1 LSB 3
DNL Differential non-linearity error — VDACR =
VREF_OUT
±1 LSB 4
VOFFSET Offset error ±0.4 ±0.8 %FSR 5
EGGain error ±0.1 ±0.6 %FSR 5
PSRR Power supply rejection ratio, VDDA ≥ 2.4 V 60 90 dB
TCO Temperature coefficient offset voltage 3.7 μV/C 6
TGE Temperature coefficient gain error 0.000421 %FSR/C
Rop Output resistance (load = 3 kΩ) 250 Ω
SR Slew rate -80hF7Fh80h
1.2
1.7
V/μs
Table continues on the next page...
Peripheral operating requirements and behaviors
34 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Table 29. 12-bit DAC operating behaviors (continued)
Symbol Description Min. Typ. Max. Unit Notes
High power (SPHP)
Low power (SPLP)
0.05 0.12
BW 3dB bandwidth
High power (SPHP)
Low power (SPLP)
550
40
kHz
1. Settling within ±1 LSB
2. The INL is measured for 0 + 100 mV to VDACR −100 mV
3. The DNL is measured for 0 + 100 mV to VDACR −100 mV
4. The DNL is measured for 0 + 100 mV to VDACR −100 mV with VDDA > 2.4 V
5. Calculated by a best fit curve from VSS + 100 mV to VDACR − 100 mV
6. VDDA = 3.0 V, reference select set for VDDA (DACx_CO:DACRFS = 1), high power mode (DACx_C0:LPEN = 0), DAC
set to 0x800, temperature range is across the full range of the device
Digital Code
DAC12 INL (LSB)
0
500 1000 1500 2000 2500 3000 3500 4000
2
4
6
8
-2
-4
-6
-8
0
Figure 12. Typical INL error vs. digital code
Peripheral operating requirements and behaviors
Kinetis KL25 Sub-Family, Rev5 08/2014. 35
Freescale Semiconductor, Inc.
Temperature °C
DAC12 Mid Level Code Voltage
25 55 85 105 125
1.499
-40
1.4985
1.498
1.4975
1.497
1.4965
1.496
Figure 13. Offset at half scale vs. temperature
3.7 Timers
See General switching specifications.
3.8 Communication interfaces
3.8.1 USB electrical specifications
The USB electricals for the USB On-the-Go module conform to the standards
documented by the Universal Serial Bus Implementers Forum. For the most up-to-date
standards, visit usb.org.
Peripheral operating requirements and behaviors
36 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
NOTE
The MCGPLLCLK meets the USB jitter specifications for
certification with the use of an external clock/crystal for
both Device and Host modes.
The MCGFLLCLK does not meet the USB jitter
specifications for certification.
3.8.2 USB VREG electrical specifications
Table 30. USB VREG electrical specifications
Symbol Description Min. Typ.1Max. Unit Notes
VREGIN Input supply voltage 2.7 5.5 V
IDDon Quiescent current — Run mode, load current
equal zero, input supply (VREGIN) > 3.6 V
125 186 μA
IDDstby Quiescent current — Standby mode, load
current equal zero
1.1 10 μA
IDDoff Quiescent current — Shutdown mode
VREGIN = 5.0 V and temperature=25 °C
Across operating voltage and
temperature
650
4
nA
μA
ILOADrun Maximum load current — Run mode 120 mA
ILOADstby Maximum load current — Standby mode 1 mA
VReg33out Regulator output voltage — Input supply
(VREGIN) > 3.6 V
Run mode
Standby mode
3
2.1
3.3
2.8
3.6
3.6
V
V
VReg33out Regulator output voltage — Input supply
(VREGIN) < 3.6 V, pass-through mode
2.1 3.6 V 2
COUT External output capacitor 1.76 2.2 8.16 μF
ESR External output capacitor equivalent series
resistance
1 100
ILIM Short circuit current 290 mA
1. Typical values assume VREGIN = 5.0 V, Temp = 25 °C unless otherwise stated.
2. Operating in pass-through mode: regulator output voltage equal to the input voltage minus a drop proportional to ILoad.
Peripheral operating requirements and behaviors
Kinetis KL25 Sub-Family, Rev5 08/2014. 37
Freescale Semiconductor, Inc.
3.8.3 SPI switching specifications
The Serial Peripheral Interface (SPI) provides a synchronous serial bus with master and
slave operations. Many of the transfer attributes are programmable. The following
tables provide timing characteristics for classic SPI timing modes. See the SPI chapter
of the chip's Reference Manual for information about the modified transfer formats used
for communicating with slower peripheral devices.
All timing is shown with respect to 20% VDD and 80% VDD thresholds, unless noted, as
well as input signal transitions of 3 ns and a 30 pF maximum load on all SPI pins.
Table 31. SPI master mode timing on slew rate disabled pads
Num. Symbol Description Min. Max. Unit Note
1 fop Frequency of operation fperiph/2048 fperiph/2 Hz 1
2 tSPSCK SPSCK period 2 x tperiph 2048 x
tperiph
ns 2
3 tLead Enable lead time 1/2 tSPSCK
4 tLag Enable lag time 1/2 tSPSCK
5 tWSPSCK Clock (SPSCK) high or low time tperiph – 30 1024 x
tperiph
ns
6 tSU Data setup time (inputs) 16 ns
7 tHI Data hold time (inputs) 0 ns
8 tvData valid (after SPSCK edge) 10 ns
9 tHO Data hold time (outputs) 0 ns
10 tRI Rise time input tperiph – 25 ns
tFI Fall time input
11 tRO Rise time output 25 ns
tFO Fall time output
1. For SPI0, fperiph is the bus clock (fBUS). For SPI1 fperiph is the system clock (fSYS).
2. tperiph = 1/fperiph
Table 32. SPI master mode timing on slew rate enabled pads
Num. Symbol Description Min. Max. Unit Note
1 fop Frequency of operation fperiph/2048 fperiph/2 Hz 1
2 tSPSCK SPSCK period 2 x tperiph 2048 x
tperiph
ns 2
3 tLead Enable lead time 1/2 tSPSCK
4 tLag Enable lag time 1/2 tSPSCK
5 tWSPSCK Clock (SPSCK) high or low time tperiph – 30 1024 x
tperiph
ns
6 tSU Data setup time (inputs) 96 ns
Table continues on the next page...
Peripheral operating requirements and behaviors
38 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Table 32. SPI master mode timing on slew rate enabled pads (continued)
Num. Symbol Description Min. Max. Unit Note
7 tHI Data hold time (inputs) 0 ns
8 tvData valid (after SPSCK edge) 52 ns
9 tHO Data hold time (outputs) 0 ns
10 tRI Rise time input tperiph – 25 ns
tFI Fall time input
11 tRO Rise time output 36 ns
tFO Fall time output
1. For SPI0, fperiph is the bus clock (fBUS). For SPI1 fperiph is the system clock (fSYS).
2. tperiph = 1/fperiph
(OUTPUT)
2
8
6 7
MSB IN2
LSB IN
MSB OUT2 LSB OUT
9
5
5
3
(CPOL=0)
4
11
11
10
10
SPSCK
SPSCK
(CPOL=1)
2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB.
1. If configured as an output.
SS1
(OUTPUT)
(OUTPUT)
MOSI
(OUTPUT)
MISO
(INPUT) BIT 6 . . . 1
BIT 6 . . . 1
Figure 14. SPI master mode timing (CPHA = 0)
Peripheral operating requirements and behaviors
Kinetis KL25 Sub-Family, Rev5 08/2014. 39
Freescale Semiconductor, Inc.
<<CLASSIFICATION>>
<<NDA MESSAGE>>
38
2
6 7
MSB IN2
BIT 6 . . . 1
MASTER MSB OUT2 MASTER LSB OUT
5
5
8
10 11
PORT DATA PORT DATA
310 11 4
1.If configured as output
2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB.
9
(OUTPUT)
(CPOL=0)
SPSCK
SPSCK
(CPOL=1)
SS1
(OUTPUT)
(OUTPUT)
MOSI
(OUTPUT)
MISO
(INPUT) LSB IN
BIT 6 . . . 1
Figure 15. SPI master mode timing (CPHA = 1)
Table 33. SPI slave mode timing on slew rate disabled pads
Num. Symbol Description Min. Max. Unit Note
1 fop Frequency of operation 0 fperiph/4 Hz 1
2 tSPSCK SPSCK period 4 x tperiph ns 2
3 tLead Enable lead time 1 tperiph
4 tLag Enable lag time 1 tperiph
5 tWSPSCK Clock (SPSCK) high or low time tperiph – 30 ns
6 tSU Data setup time (inputs) 2 ns
7 tHI Data hold time (inputs) 7 ns
8 taSlave access time tperiph ns 3
9 tdis Slave MISO disable time tperiph ns 4
10 tvData valid (after SPSCK edge) 22 ns
11 tHO Data hold time (outputs) 0 ns
12 tRI Rise time input tperiph – 25 ns
tFI Fall time input
13 tRO Rise time output 25 ns
tFO Fall time output
1. For SPI0, fperiph is the bus clock (fBUS). For SPI1 fperiph is the system clock (fSYS).
2. tperiph = 1/fperiph
3. Time to data active from high-impedance state
4. Hold time to high-impedance state
Peripheral operating requirements and behaviors
40 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Table 34. SPI slave mode timing on slew rate enabled pads
Num. Symbol Description Min. Max. Unit Note
1 fop Frequency of operation 0 fperiph/4 Hz 1
2 tSPSCK SPSCK period 4 x tperiph ns 2
3 tLead Enable lead time 1 tperiph
4 tLag Enable lag time 1 tperiph
5 tWSPSCK Clock (SPSCK) high or low time tperiph – 30 ns
6 tSU Data setup time (inputs) 2 ns
7 tHI Data hold time (inputs) 7 ns
8 taSlave access time tperiph ns 3
9 tdis Slave MISO disable time tperiph ns 4
10 tvData valid (after SPSCK edge) 122 ns
11 tHO Data hold time (outputs) 0 ns
12 tRI Rise time input tperiph – 25 ns
tFI Fall time input
13 tRO Rise time output 36 ns
tFO Fall time output
1. For SPI0, fperiph is the bus clock (fBUS). For SPI1 fperiph is the system clock (fSYS).
2. tperiph = 1/fperiph
3. Time to data active from high-impedance state
4. Hold time to high-impedance state
2
10
6 7
MSB IN
BIT 6 . . . 1
SLAVE MSB SLAVE LSB OUT
11
5
5
3
8
4
13
NOTE: Not defined
12
12
11
SEE
NOTE
13
9
see
note
(INPUT)
(CPOL=0)
SPSCK
SPSCK
(CPOL=1)
SS
(INPUT)
(INPUT)
MOSI
(INPUT)
MISO
(OUTPUT)
LSB IN
BIT 6 . . . 1
Figure 16. SPI slave mode timing (CPHA = 0)
Peripheral operating requirements and behaviors
Kinetis KL25 Sub-Family, Rev5 08/2014. 41
Freescale Semiconductor, Inc.
2
6 7
MSB IN
BIT 6 . . . 1
MSB OUT SLAVE LSB OUT
5
5
10
12 13
312 13
4
SLAVE
8
9
see
note
(INPUT)
(CPOL=0)
SPSCK
SPSCK
(CPOL=1)
SS
(INPUT)
(INPUT)
MOSI
(INPUT)
MISO
(OUTPUT)
NOTE: Not defined
11
LSB IN
BIT 6 . . . 1
Figure 17. SPI slave mode timing (CPHA = 1)
3.8.4 Inter-Integrated Circuit Interface (I2C) timing
Table 35. I2C timing
Characteristic Symbol Standard Mode Fast Mode Unit
Minimum Maximum Minimum Maximum
SCL Clock Frequency fSCL 0 100 0 4001kHz
Hold time (repeated) START condition.
After this period, the first clock pulse is
generated.
tHD; STA 4 0.6 µs
LOW period of the SCL clock tLOW 4.7 1.3 µs
HIGH period of the SCL clock tHIGH 4 0.6 µs
Set-up time for a repeated START
condition
tSU; STA 4.7 0.6 µs
Data hold time for I2C bus devices tHD; DAT 023.453040.92µs
Data set-up time tSU; DAT 2505 1003, 6 ns
Rise time of SDA and SCL signals tr 1000 20 +0.1Cb7300 ns
Fall time of SDA and SCL signals tf 300 20 +0.1Cb6300 ns
Set-up time for STOP condition tSU; STO 4 0.6 µs
Bus free time between STOP and
START condition
tBUF 4.7 1.3 µs
Pulse width of spikes that must be
suppressed by the input filter
tSP N/A N/A 0 50 ns
1. The maximum SCL Clock Frequency in Fast mode with maximum bus loading can only achieved when using the High
drive pins (see Voltage and current operating behaviors) or when using the Normal drive pins and VDD ≥ 2.7 V
Peripheral operating requirements and behaviors
42 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
2. The master mode I2C deasserts ACK of an address byte simultaneously with the falling edge of SCL. If no slaves
acknowledge this address byte, then a negative hold time can result, depending on the edge rates of the SDA and
SCL lines.
3. The maximum tHD; DAT must be met only if the device does not stretch the LOW period (tLOW) of the SCL signal.
4. Input signal Slew = 10 ns and Output Load = 50 pF
5. Set-up time in slave-transmitter mode is 1 IPBus clock period, if the TX FIFO is empty.
6. A Fast mode I2C bus device can be used in a Standard mode I2C bus system, but the requirement tSU; DAT ≥ 250 ns
must then be met. This is automatically the case if the device does not stretch the LOW period of the SCL signal. If
such a device does stretch the LOW period of the SCL signal, then it must output the next data bit to the SDA line trmax
+ tSU; DAT = 1000 + 250 = 1250 ns (according to the Standard mode I2C bus specification) before the SCL line is
released.
7. Cb = total capacitance of the one bus line in pF.
SDA
HD; STA tHD; DAT
tLOW
tSU; DAT
tHIGH
tSU; STA SR PS
S
tHD; STA tSP
tSU; STO
tBUF
tftr
tftr
SCL
Figure 18. Timing definition for fast and standard mode devices on the I2C bus
3.8.5 UART
See General switching specifications.
3.9 Human-machine interfaces (HMI)
3.9.1 TSI electrical specifications
Table 36. TSI electrical specifications
Symbol Description Min. Typ. Max. Unit
TSI_RUNF Fixed power consumption in run mode 100 µA
TSI_RUNV Variable power consumption in run mode
(depends on oscillator's current selection)
1.0 128 µA
TSI_EN Power consumption in enable mode 100 µA
TSI_DIS Power consumption in disable mode 1.2 µA
TSI_TEN TSI analog enable time 66 µs
TSI_CREF TSI reference capacitor 1.0 pF
TSI_DVOLT Voltage variation of VP & VM around nominal
values
0.19 1.03 V
Peripheral operating requirements and behaviors
Kinetis KL25 Sub-Family, Rev5 08/2014. 43
Freescale Semiconductor, Inc.
4 Dimensions
4.1 Obtaining package dimensions
Package dimensions are provided in package drawings.
To find a package drawing, go to freescale.com and perform a keyword search for the
drawing’s document number:
If you want the drawing for this package Then use this document number
32-pin QFN 98ASA00473D
48-pin QFN 98ASA00466D
64-pin LQFP 98ASS23234W
80-pin LQFP 98ASS23174W
5 Pinout
5.1 KL25 Signal Multiplexing and Pin Assignments
The following table shows the signals available on each pin and the locations of these
pins on the devices supported by this document. The Port Control Module is responsible
for selecting which ALT functionality is available on each pin.
80
LQFP
64
LQFP
48
QFN
32
QFN
Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 ALT7
1 1 1 PTE0 DISABLED PTE0 UART1_TX RTC_
CLKOUT
CMP0_OUT I2C1_SDA
2 2 PTE1 DISABLED PTE1 SPI1_MOSI UART1_RX SPI1_MISO I2C1_SCL
3 PTE2 DISABLED PTE2 SPI1_SCK
4 PTE3 DISABLED PTE3 SPI1_MISO SPI1_MOSI
5 PTE4 DISABLED PTE4 SPI1_PCS0
6 PTE5 DISABLED PTE5
7 3 1 VDD VDD VDD
8 4 2 2 VSS VSS VSS
9 5 3 3 USB0_DP USB0_DP USB0_DP
10 6 4 4 USB0_DM USB0_DM USB0_DM
Dimensions
44 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
80
LQFP
64
LQFP
48
QFN
32
QFN
Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 ALT7
11 7 5 5 VOUT33 VOUT33 VOUT33
12 8 6 6 VREGIN VREGIN VREGIN
13 9 7 PTE20 ADC0_DP0/
ADC0_SE0
ADC0_DP0/
ADC0_SE0
PTE20 TPM1_CH0 UART0_TX
14 10 8 PTE21 ADC0_DM0/
ADC0_SE4a
ADC0_DM0/
ADC0_SE4a
PTE21 TPM1_CH1 UART0_RX
15 11 PTE22 ADC0_DP3/
ADC0_SE3
ADC0_DP3/
ADC0_SE3
PTE22 TPM2_CH0 UART2_TX
16 12 PTE23 ADC0_DM3/
ADC0_SE7a
ADC0_DM3/
ADC0_SE7a
PTE23 TPM2_CH1 UART2_RX
17 13 9 7 VDDA VDDA VDDA
18 14 10 VREFH VREFH VREFH
19 15 11 VREFL VREFL VREFL
20 16 12 8 VSSA VSSA VSSA
21 17 13 PTE29 CMP0_IN5/
ADC0_SE4b
CMP0_IN5/
ADC0_SE4b
PTE29 TPM0_CH2 TPM_
CLKIN0
22 18 14 9 PTE30 DAC0_OUT/
ADC0_SE23/
CMP0_IN4
DAC0_OUT/
ADC0_SE23/
CMP0_IN4
PTE30 TPM0_CH3 TPM_
CLKIN1
23 19 PTE31 DISABLED PTE31 TPM0_CH4
24 20 15 PTE24 DISABLED PTE24 TPM0_CH0 I2C0_SCL
25 21 16 PTE25 DISABLED PTE25 TPM0_CH1 I2C0_SDA
26 22 17 10 PTA0 SWD_CLK TSI0_CH1 PTA0 TPM0_CH5 SWD_CLK
27 23 18 11 PTA1 DISABLED TSI0_CH2 PTA1 UART0_RX TPM2_CH0
28 24 19 12 PTA2 DISABLED TSI0_CH3 PTA2 UART0_TX TPM2_CH1
29 25 20 13 PTA3 SWD_DIO TSI0_CH4 PTA3 I2C1_SCL TPM0_CH0 SWD_DIO
30 26 21 14 PTA4 NMI_b TSI0_CH5 PTA4 I2C1_SDA TPM0_CH1 NMI_b
31 27 PTA5 DISABLED PTA5 USB_CLKIN TPM0_CH2
32 28 PTA12 DISABLED PTA12 TPM1_CH0
33 29 PTA13 DISABLED PTA13 TPM1_CH1
34 PTA14 DISABLED PTA14 SPI0_PCS0 UART0_TX
35 PTA15 DISABLED PTA15 SPI0_SCK UART0_RX
36 PTA16 DISABLED PTA16 SPI0_MOSI SPI0_MISO
37 PTA17 DISABLED PTA17 SPI0_MISO SPI0_MOSI
38 30 22 15 VDD VDD VDD
39 31 23 16 VSS VSS VSS
40 32 24 17 PTA18 EXTAL0 EXTAL0 PTA18 UART1_RX TPM_
CLKIN0
41 33 25 18 PTA19 XTAL0 XTAL0 PTA19 UART1_TX TPM_
CLKIN1
LPTMR0_
ALT1
42 34 26 19 PTA20 RESET_b PTA20 RESET_b
43 35 27 20 PTB0/
LLWU_P5
ADC0_SE8/
TSI0_CH0
ADC0_SE8/
TSI0_CH0
PTB0/
LLWU_P5
I2C0_SCL TPM1_CH0
Pinout
Kinetis KL25 Sub-Family, Rev5 08/2014. 45
Freescale Semiconductor, Inc.
80
LQFP
64
LQFP
48
QFN
32
QFN
Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 ALT7
44 36 28 21 PTB1 ADC0_SE9/
TSI0_CH6
ADC0_SE9/
TSI0_CH6
PTB1 I2C0_SDA TPM1_CH1
45 37 29 PTB2 ADC0_SE12/
TSI0_CH7
ADC0_SE12/
TSI0_CH7
PTB2 I2C0_SCL TPM2_CH0
46 38 30 PTB3 ADC0_SE13/
TSI0_CH8
ADC0_SE13/
TSI0_CH8
PTB3 I2C0_SDA TPM2_CH1
47 PTB8 DISABLED PTB8 EXTRG_IN
48 PTB9 DISABLED PTB9
49 PTB10 DISABLED PTB10 SPI1_PCS0
50 PTB11 DISABLED PTB11 SPI1_SCK
51 39 31 PTB16 TSI0_CH9 TSI0_CH9 PTB16 SPI1_MOSI UART0_RX TPM_
CLKIN0
SPI1_MISO
52 40 32 PTB17 TSI0_CH10 TSI0_CH10 PTB17 SPI1_MISO UART0_TX TPM_
CLKIN1
SPI1_MOSI
53 41 PTB18 TSI0_CH11 TSI0_CH11 PTB18 TPM2_CH0
54 42 PTB19 TSI0_CH12 TSI0_CH12 PTB19 TPM2_CH1
55 43 33 PTC0 ADC0_SE14/
TSI0_CH13
ADC0_SE14/
TSI0_CH13
PTC0 EXTRG_IN CMP0_OUT
56 44 34 22 PTC1/
LLWU_P6/
RTC_CLKIN
ADC0_SE15/
TSI0_CH14
ADC0_SE15/
TSI0_CH14
PTC1/
LLWU_P6/
RTC_CLKIN
I2C1_SCL TPM0_CH0
57 45 35 23 PTC2 ADC0_SE11/
TSI0_CH15
ADC0_SE11/
TSI0_CH15
PTC2 I2C1_SDA TPM0_CH1
58 46 36 24 PTC3/
LLWU_P7
DISABLED PTC3/
LLWU_P7
UART1_RX TPM0_CH2 CLKOUT
59 47 VSS VSS VSS
60 48 VDD VDD VDD
61 49 37 25 PTC4/
LLWU_P8
DISABLED PTC4/
LLWU_P8
SPI0_PCS0 UART1_TX TPM0_CH3
62 50 38 26 PTC5/
LLWU_P9
DISABLED PTC5/
LLWU_P9
SPI0_SCK LPTMR0_
ALT2
CMP0_OUT
63 51 39 27 PTC6/
LLWU_P10
CMP0_IN0 CMP0_IN0 PTC6/
LLWU_P10
SPI0_MOSI EXTRG_IN SPI0_MISO
64 52 40 28 PTC7 CMP0_IN1 CMP0_IN1 PTC7 SPI0_MISO SPI0_MOSI
65 53 PTC8 CMP0_IN2 CMP0_IN2 PTC8 I2C0_SCL TPM0_CH4
66 54 PTC9 CMP0_IN3 CMP0_IN3 PTC9 I2C0_SDA TPM0_CH5
67 55 PTC10 DISABLED PTC10 I2C1_SCL
68 56 PTC11 DISABLED PTC11 I2C1_SDA
69 PTC12 DISABLED PTC12 TPM_
CLKIN0
70 PTC13 DISABLED PTC13 TPM_
CLKIN1
71 PTC16 DISABLED PTC16
72 PTC17 DISABLED PTC17
Pinout
46 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
80
LQFP
64
LQFP
48
QFN
32
QFN
Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 ALT7
73 57 41 PTD0 DISABLED PTD0 SPI0_PCS0 TPM0_CH0
74 58 42 PTD1 ADC0_SE5b ADC0_SE5b PTD1 SPI0_SCK TPM0_CH1
75 59 43 PTD2 DISABLED PTD2 SPI0_MOSI UART2_RX TPM0_CH2 SPI0_MISO
76 60 44 PTD3 DISABLED PTD3 SPI0_MISO UART2_TX TPM0_CH3 SPI0_MOSI
77 61 45 29 PTD4/
LLWU_P14
DISABLED PTD4/
LLWU_P14
SPI1_PCS0 UART2_RX TPM0_CH4
78 62 46 30 PTD5 ADC0_SE6b ADC0_SE6b PTD5 SPI1_SCK UART2_TX TPM0_CH5
79 63 47 31 PTD6/
LLWU_P15
ADC0_SE7b ADC0_SE7b PTD6/
LLWU_P15
SPI1_MOSI UART0_RX SPI1_MISO
80 64 48 32 PTD7 DISABLED PTD7 SPI1_MISO UART0_TX SPI1_MOSI
5.2 KL25 pinouts
The following figures show the pinout diagrams for the devices supported by this
document. Many signals may be multiplexed onto a single pin. To determine what
signals can be used on which pin, see KL25 Signal Multiplexing and Pin
Assignments.
Pinout
Kinetis KL25 Sub-Family, Rev5 08/2014. 47
Freescale Semiconductor, Inc.
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
VSSA
VREFL
VREFH
VDDA
PTE23
PTE22
PTE21
PTE20
VREGIN
VOUT33
USB0_DM
USB0_DP
VSS
VDD
PTE5
PTE4
PTE3
PTE2
PTE1
PTE0
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
PTD7
PTD6/LLWU_P15
PTD5
PTD4/LLWU_P14
PTD3
PTD2
PTD1
PTD0
PTC17
PTC16
PTC13
PTC12
PTC11
PTC10
PTC9
PTC8
PTC7
PTC6/LLWU_P10
PTC5/LLWU_P9
PTC4/LLWU_P8
VDD
VSS
PTC3/LLWU_P7
PTC2
PTC1/LLWU_P6/RTC_CLKIN
PTC0
PTB19
PTB18
PTB17
PTB16
PTB11
PTB10
PTB9
PTB8
PTB3
PTB2
PTB1
PTB0/LLWU_P5
PTA20
PTA19
PTA18
VSS
VDD
PTA17
PTA16
PTA15
PTA14
PTA13
PTA12
PTA5
PTA4
PTA3
PTA2
PTA1
PTA0
PTE25
PTE24
PTE31
PTE30
PTE29
Figure 19. KL25 80-pin LQFP pinout diagram
Pinout
48 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
PTE24
PTE31
PTE30
PTE29
VSSA
VREFL
VREFH
VDDA
PTE23
PTE22
PTE21
PTE20
VREGIN
VOUT33
USB0_DM
USB0_DP
VSS
VDD
PTE1
PTE0
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
64
63
62
61
PTD7
PTD6/LLWU_P15
PTD5
PTD4/LLWU_P14
PTD3
PTD2
PTD1
PTD0
PTC11
PTC10
PTC9
PTC8
PTC7
PTC6/LLWU_P10
PTC5/LLWU_P9
PTC4/LLWU_P8
VDD
VSS
PTC3/LLWU_P7
PTC2
PTC1/LLWU_P6/RTC_CLKIN
PTC0
PTB19
PTB18
PTB17
PTB16
PTB3
PTB2
PTB1
PTB0/LLWU_P5
PTA20
PTA19
PTA18
VSS
VDD
PTA13
PTA12
PTA5
PTA4
PTA3
PTA2
PTA1
PTA0
PTE25
Figure 20. KL25 64-pin LQFP pinout diagram
Pinout
Kinetis KL25 Sub-Family, Rev5 08/2014. 49
Freescale Semiconductor, Inc.
VSSA
VREFL
VREFH
VDDA
PTE21
PTE20
VREGIN
VOUT33
USB0_DM
USB0_DP
VSS
VDD
12
11
10
9
8
7
6
5
4
3
2
1
48
47
46
45
44
43
42
41
40
39
38
37
PTD7
PTD6/LLWU_P15
PTD5
PTD4/LLWU_P14
PTD3
PTD2
PTD1
PTD0
PTC7
PTC6/LLWU_P10
PTC5/LLWU_P9
PTC4/LLWU_P8
36
35
34
33
PTC3/LLWU_P7
PTC2
PTC1/LLWU_P6/RTC_CLKIN
PTC0
32
31
30
29
28
27
26
25
PTB17
PTB16
PTB3
PTB2
PTB1
PTB0/LLWU_P5
PTA20
PTA19
PTA3
PTA2
PTA1
PTA0
24
23
22
21
20
19
18
17
PTE25
PTE24
PTE30
PTE29
16
15
14
13
PTA18
VSS
VDD
PTA4
Figure 21. KL25 48-pin QFN pinout diagram
Pinout
50 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
32
31
30
29
28
27
26
25
PTD7
PTD6/LLWU_P15
PTD5
PTD4/LLWU_P14
PTC7
PTC6/LLWU_P10
PTC5/LLWU_P9
PTC4/LLWU_P8
PTA2
PTA1
PTA0
PTE30
12
11
10
9
VSS
VDD
PTA4
PTA3
16
15
14
13
PTB0/LLWU_P5
PTA20
PTA19
PTA18
24
23
22
21
20
19
18
17
PTC3/LLWU_P7
PTC2
PTC1/LLWU_P6/RTC_CLKIN
PTB1
VSSA
VDDA
VREGIN
VOUT33
USB0_DM
USB0_DP
VSS
PTE0
8
7
6
5
4
3
2
1
Figure 22. KL25 32-pin QFN pinout diagram
6Ordering parts
6.1 Determining valid orderable parts
Valid orderable part numbers are provided on the web. To determine the orderable
part numbers for this device, go to freescale.com and perform a part number search
for the following device numbers: PKL25 and MKL25
7Part identification
Ordering parts
Kinetis KL25 Sub-Family, Rev5 08/2014. 51
Freescale Semiconductor, Inc.
7.1 Description
Part numbers for the chip have fields that identify the specific part. You can use the
values of these fields to determine the specific part you have received.
7.2 Format
Part numbers for this device have the following format:
Q KL## A FFF R T PP CC N
7.3 Fields
This table lists the possible values for each field in the part number (not all
combinations are valid):
Table 37. Part number fields descriptions
Field Description Values
Q Qualification status M = Fully qualified, general market flow
P = Prequalification
KL## Kinetis family KL25
A Key attribute Z = Cortex-M0+
FFF Program flash memory size 32 = 32 KB
64 = 64 KB
128 = 128 KB
R Silicon revision (Blank) = Main
A = Revision after main
T Temperature range (°C) V = –40 to 105
PP Package identifier FM = 32 QFN (5 mm x 5 mm)
FT = 48 QFN (7 mm x 7 mm)
LH = 64 LQFP (10 mm x 10 mm)
LK = 80 LQFP (12 mm x 12 mm)
CC Maximum CPU frequency (MHz) 4 = 48 MHz
N Packaging type R = Tape and reel
(Blank) = Trays
Part identification
52 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
7.4 Example
This is an example part number:
MKL25Z64VLK4
8 Terminology and guidelines
8.1 Definition: Operating requirement
An operating requirement is a specified value or range of values for a technical
characteristic that you must guarantee during operation to avoid incorrect operation
and possibly decreasing the useful life of the chip.
8.1.1 Example
This is an example of an operating requirement:
Symbol Description Min. Max. Unit
VDD 1.0 V core supply
voltage
0.9 1.1 V
8.2 Definition: Operating behavior
Unless otherwise specified, an operating behavior is a specified value or range of
values for a technical characteristic that are guaranteed during operation if you meet
the operating requirements and any other specified conditions.
8.2.1 Example
This is an example of an operating behavior:
Symbol Description Min. Max. Unit
IWP Digital I/O weak pullup/
pulldown current
10 130 µA
Terminology and guidelines
Kinetis KL25 Sub-Family, Rev5 08/2014. 53
Freescale Semiconductor, Inc.
8.3 Definition: Attribute
An attribute is a specified value or range of values for a technical characteristic that are
guaranteed, regardless of whether you meet the operating requirements.
8.3.1 Example
This is an example of an attribute:
Symbol Description Min. Max. Unit
CIN_D Input capacitance:
digital pins
7 pF
8.4 Definition: Rating
A rating is a minimum or maximum value of a technical characteristic that, if exceeded,
may cause permanent chip failure:
Operating ratings apply during operation of the chip.
Handling ratings apply when the chip is not powered.
8.4.1 Example
This is an example of an operating rating:
Symbol Description Min. Max. Unit
VDD 1.0 V core supply
voltage
–0.3 1.2 V
Terminology and guidelines
54 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
8.5 Result of exceeding a rating
40
30
20
10
0
Measured characteristic
Operating rating
Failures in time (ppm)
The likelihood of permanent chip failure increases rapidly as
soon as a characteristic begins to exceed one of its operating ratings.
8.6 Relationship between ratings and operating requirements
- No permanent failure
- Correct operation
Normal operating range
Fatal range
Expected permanent failure
Fatal range
Expected permanent failure
Operating rating (max.)
Operating requirement (max.)
Operating requirement (min.)
Operating rating (min.)
Operating (power on)
Degraded operating range Degraded operating range
No permanent failure
Handling range
Fatal range
Expected permanent failure
Fatal range
Expected permanent failure
Handling rating (max.)
Handling rating (min.)
Handling (power off)
- No permanent failure
- Possible decreased life
- Possible incorrect operation
- No permanent failure
- Possible decreased life
- Possible incorrect operation
8.7 Guidelines for ratings and operating requirements
Follow these guidelines for ratings and operating requirements:
Never exceed any of the chip’s ratings.
During normal operation, don’t exceed any of the chip’s operating requirements.
If you must exceed an operating requirement at times other than during normal
operation (for example, during power sequencing), limit the duration as much as
possible.
Terminology and guidelines
Kinetis KL25 Sub-Family, Rev5 08/2014. 55
Freescale Semiconductor, Inc.
8.8 Definition: Typical value
A typical value is a specified value for a technical characteristic that:
Lies within the range of values specified by the operating behavior
Given the typical manufacturing process, is representative of that characteristic
during operation when you meet the typical-value conditions or other specified
conditions
Typical values are provided as design guidelines and are neither tested nor guaranteed.
8.8.1 Example 1
This is an example of an operating behavior that includes a typical value:
Symbol Description Min. Typ. Max. Unit
IWP Digital I/O weak
pullup/pulldown
current
10 70 130 µA
8.8.2 Example 2
This is an example of a chart that shows typical values for various voltage and
temperature conditions:
Terminology and guidelines
56 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
0.90 0.95 1.00 1.05 1.10
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
150 °C
105 °C
25 °C
–40 °C
VDD (V)
I(μA)
DD_STOP
TJ
8.9 Typical value conditions
Typical values assume you meet the following conditions (or other conditions as
specified):
Table 38. Typical value conditions
Symbol Description Value Unit
TAAmbient temperature 25 °C
VDD 3.3 V supply voltage 3.3 V
9 Revision history
The following table provides a revision history for this document.
Table 39. Revision history
Rev. No. Date Substantial Changes
2 9/2012 Completed all the TBDs, initial public release.
3 9/2012 Updated Signal Multiplexing and Pin Assignments table to add UART2
signals.
4 3/2014 Updated the front page and restructured the chapters
Table continues on the next page...
Revision history
Kinetis KL25 Sub-Family, Rev5 08/2014. 57
Freescale Semiconductor, Inc.
Table 39. Revision history (continued)
Rev. No. Date Substantial Changes
Added a note to the ILAT in the ESD handling ratings
Updated Voltage and current operating ratings
Updated Voltage and current operating requirements
Updated the Voltage and current operating behaviors
Updated Power mode transition operating behaviors
Updated Capacitance attributes
Updated footnote in the Device clock specifications
Updated tersall in the Flash timing specifications — commands
Updated VADIN in the 16-bit ADC operating conditions
Updated Temp sensor slope and voltage and added a note to
them in the 16-bit ADC electrical characteristics
Removed TA in the 12-bit DAC operating requirements
Added Inter-Integrated Circuit Interface (I2C) timing
508/2014 Updated related source and added block diagram in the front
page
Updated Power consumption operating behaviors
Updated the note in USB electrical specifications
Revision history
58 Kinetis KL25 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
How to Reach Us:
Home Page:
freescale.com
Web Support:
freescale.com/support
Document Number KL25P80M48SF0
Revision 5 08/2014
© 2012-2014 Freescale Semiconductor, Inc.
Information in this document is provided solely to enable system and
software implementers to use Freescale products. There are no express
or implied copyright licenses granted hereunder to design or fabricate
any integrated circuits based on the information in this document.
Freescale reserves the right to make changes without further notice to
any products herein.
Freescale makes no warranty, representation, or guarantee regarding
the suitability of its products for any particular purpose, nor does
Freescale assume any liability arising out of the application or use of
any product or circuit, and specifically disclaims any and all liability,
including without limitation consequential or incidental damages.
“Typical” parameters that may be provided in Freescale data sheets
and/or specifications can and do vary in different applications, and
actual performance may vary over time. All operating parameters,
including “typicals,” must be validated for each customer application by
customer's technical experts. Freescale does not convey any license
under its patent rights nor the rights of others. Freescale sells products
pursuant to standard terms and conditions of sale, which can be found
at the following address: freescale.com/SalesTermsandConditions.
Freescale, Freescale logo, Energy Efficient Solutions logo, and Kinetis
are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm.
Off. All other product or service names are the property of their
respective owners. ARM and Cortex are registered trademarks of ARM
Limited (or its subsidiaries) in the EU and/or elsewhere. All rights
reserved.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Freescale Semiconductor:
MKL25Z128VFM4 MKL25Z128VFT4 MKL25Z128VLH4 MKL25Z128VLK4 MKL25Z32VFM4 MKL25Z32VFT4
MKL25Z32VLH4 MKL25Z32VLK4 MKL25Z64VFM4 MKL25Z64VFT4 MKL25Z64VLH4 MKL25Z64VLK4