MC74HCT374A Octal 3-State Noninverting D Flip-Flop with LSTTL-Compatible Inputs High-Performance Silicon-Gate CMOS The MC74HCT374A may be used as a level converter for interfacing TTL or NMOS outputs to High-Speed CMOS inputs. The HCT374A is identical in pinout to the LS374. Data meeting the setup and hold time is clocked to the outputs with the rising edge of Clock. The Output Enable does not affect the state of the flip-flops, but when Output Enable is high, the outputs are forced to the high-impedance state. Thus, data may be stored even when the outputs are not enabled. The HCT374A is identical in function to the HCT574A, which has the input pins on the opposite side of the package from the output pins. This device is similar in function to the HCT534A, which has inverting outputs. http://onsemi.com MARKING DIAGRAMS PDIP-20 N SUFFIX CASE 738 20 1 * MC74HCT374AN AWLYYWWG 1 20 20 1 SOIC-20 DW SUFFIX CASE 751D Features * * * * * * * * 20 HCT374A AWLYYWWG 1 Output Drive Capability: 15 LSTTL Loads TTL/NMOS-Compatible Input Levels Outputs Directly Interface to CMOS, NMOS, and TTL Operating Voltage Range: 4.5 to 5.5 V Low Input Current: 1.0 mA In Compliance With the JEDEC Standard No. 7.0 A Requirements Chip Complexity: 276 FETs or 69 Equivalent Gates Improvements over HCT374 -- Improved Propagation Delays -- 50% Lower Quiescent Power -- Improved Input Noise and Latchup Immunity These Devices are Pb-Free and are RoHS Compliant 20 20 1 TSSOP-20 DT SUFFIX CASE 948E HCT 374A ALYWG G 1 20 SOEIAJ-20 F SUFFIX CASE 967 20 1 74HCT374A AWLYYWWG 1 A WL, L YY, Y WW, W G or G = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package (Note: Microdot may be in either location) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet. (c) Semiconductor Components Industries, LLC, 2011 May, 2011 - Rev. 11 1 Publication Order Number: MC74HCT374A/D MC74HCT374A PIN ASSIGNMENT OUTPUT ENABLE Q0 LOGIC DIAGRAM D0 D1 D2 DATA INPUTS D3 D4 D5 D6 D7 CLOCK OUTPUT ENABLE 3 2 4 5 7 6 8 9 13 12 14 15 17 16 18 19 20 VCC 2 19 Q7 D0 3 18 D7 D6 D1 4 17 Q0 Q1 5 16 Q6 Q1 Q2 6 15 Q5 Q2 D2 7 14 D5 D3 8 13 D4 Q3 9 12 Q4 10 11 CLOCK Q3 NONINVERTING OUTPUTS Q4 Q5 GND Q6 FUNCTION TABLE Q7 11 1 1 Inputs Output Enable PIN 20 = VCC PIN 10 = GND L L L H IIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIII Value Units Internal Gate Count* Design Criteria 69 ea. Internal Gate Propagation Delay 1.5 ns Internal Gate Power Dissipation 5.0 mW .0075 pJ Speed Power Product Output Clock D Q L,H, X H L X X H L No Change Z X = don't care Z = high impedance *Equivalent to a two-input NAND gate. ORDERING INFORMATION Package Shipping MC74HCT374ANG PDIP-20 (Pb-Free) 1440 Units / Box MC74HCT374ADWG SOIC-20 (Pb-Free) 38 Units / Rail MC74HCT374ADWR2G SOIC-20 (Pb-Free) 1000 Units / Reel MC74HCT374ADTR2G TSSOP-20* 2500 Units / Reel MC74HCT374AFELG SOEIAJ-20 (Pb-Free) 2000 Units / Reel Device For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *This package is inherently Pb-Free. http://onsemi.com 2 MC74HCT374A IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIII IIIII III IIIIIIIIIIIIIIIIIIIIIIIIII MAXIMUM RATINGS Symbol Parameter Value Unit - 0.5 to + 7.0 V V VCC DC Supply Voltage (Referenced to GND) Vin DC Input Voltage (Referenced to GND) - 0.5 to VCC + 0.5 Vout DC Output Voltage (Referenced to GND) - 0.5 to VCC + 0.5 V Iin DC Input Current, per Pin 20 mA Iout DC Output Current, per Pin 35 mA ICC DC Supply Current, VCC and GND Pins 75 mA PD Power Dissipation in Still Air, 750 500 450 mW Tstg Storage Temperature - 65 to + 150 _C TL Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP, SOIC, SSOP or TSSOP Package) Plastic DIP SOIC Package TSSOP Package This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, Vin and Vout should be constrained to the range GND v (Vin or Vout) v VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. _C 260 Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. Derating -- Plastic DIP: - 10 mW/_C from 65_ to 125_C SOIC Package: - 7 mW/_C from 65_ to 125_C TSSOP Package: - 6.1 mW/_C from 65_ to 125_C IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIII IIIIIIIII III IIIIIIIIII II IIII IIII IIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIII IIIIIIIII III IIII IIII IIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIII IIIIIIIII III IIII IIII IIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIII II IIIIIIII IIIIII IIII IIIIII IIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIIIIIIIIII IIIIIIII II IIIII IIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII RECOMMENDED OPERATING CONDITIONS Symbol VCC Vin, Vout Parameter Min DC Supply Voltage (Referenced to GND) Max Unit 4.5 5.5 V 0 VCC V - 55 + 125 _C 0 500 ns DC Input Voltage, Output Voltage (Referenced to GND) TA Operating Temperature, All Package Types tr, tf Input Rise and Fall Time (Figure 1) DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) Guaranteed Limit Symbol Parameter Test Conditions VCC V - 55 to 25_C v 85_C v 125_C Unit VIH Minimum High-Level Input Voltage Vout = 0.1 V or VCC - 0.1 V |Iout| v 20 mA 4.5 5.5 2.0 2.0 2.0 2.0 2.0 2.0 V VIL Maximum Low-Level Input Voltage Vout = 0.1 V or VCC - 0.1 V |Iout| v 20 mA 4.5 5.5 0.8 0.8 0.8 0.8 0.8 0.8 V VOH Minimum High-Level Output Voltage Vin = VIH or VIL |Iout| v 20 mA 4.5 5.5 4.4 5.4 4.4 5.4 4.4 5.4 V Vin = VIH or VIL |Iout| v 6.0 mA 4.5 3.98 3.84 3.7 Vin = VIH or VIL |Iout| v 20 mA 4.5 5.5 0.1 0.1 0.1 0.1 0.1 0.1 Vin = VIH or VIL |Iout| v 6.0 mA 4.5 0.26 0.33 0.4 VOL Maximum Low-Level Output Voltage V Iin Maximum Input Leakage Current Vin = VCC or GND 5.5 0.1 1.0 1.0 mA IOZ Maximum Three-State Leakage Current Output in High-Impedance State Vin = VIL or VIH Vout = VCC or GND 5.5 0.5 5.0 10 mA ICC Maximum Quiescent Supply Current (per Package) Vin = VCC or GND Iout = 0 mA 5.5 4.0 40 160 mA DICC Additional Quiescent Supply Current Vin = 2.4 V, Any One Input Vin = VCC or GND, Other Inputs lout = 0 mA 1. Total Supply Current = ICC + DICC. http://onsemi.com 3 5.5 -55_C 25_C to 125_C 2.9 2.4 mA MC74HCT374A IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIII IIIIIIIIIII IIII IIIIIIIIIIIIIIIIII IIIII IIII IIIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIIII IIIII IIII IIIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII AC ELECTRICAL CHARACTERISTICS (VCC = 5.0 V 10%, CL = 50 pF, Input tr = tf = 6.0 ns) Guaranteed Limit - 55 to 25_C v 85_C v 125_C Unit fmax Maximum Clock Frequency (50% Duty Cycle) (Figures 1 and 4) 30 24 20 MHz tPLH, tPHL Maximum Propagation Delay, Clock to Q (Figures 1 and 4) 31 39 47 ns tPLZ, tPHZ Maximum Propagation Delay, Output Enable to Q (Figures 2 and 5) 30 38 45 ns tPZL, tPZH Maximum Propagation Delay, Output Enable to Q (Figures 2 and 5) 30 38 45 ns tTLH, tTHL Maximum Output Transition Time, Any Output (Figures 1 and 4) 12 15 18 ns Cin Maximum Input Capacitance 10 10 10 pF Cout Maximum Three-State Output Capacitance (Output in High-Impedance State) 15 15 15 pF Symbol Parameter Typical @ 25C, VCC = 5.0 V CPD Power Dissipation Capacitance (Per Flip-Flop)* 65 pF * Used to determine the no-load dynamic power consumption: P D = CPD VCC 2 f + ICC VCC . IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIII IIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII TIMING REQUIREMENTS (VCC = 5.0 V 10%, Input tr = tf = 6.0 ns) Guaranteed Limit Symbol Parameter - 55 to 25_C v 85_C v 125_C Unit tsu Minimum Setup Time, Data to Clock (Figure 3) 12 15 18 ns th Minimum Hold Time, Clock to Data (Figure 3) 5.0 5.0 5.0 ns tw Minimum Pulse Width, Clock (Figure 1) 12 15 18 ns Maximum Input Rise and Fall Times (Figure 1) 500 500 500 ns tr, tf http://onsemi.com 4 MC74HCT374A SWITCHING WAVEFORMS tr CLOCK tf 3V OUTPUT ENABLE VCC 2.7 V 1.3 V 0.3 V tw GND GND Q 1/fmax tPZL tPLZ tPZH tPHZ 90% 1.3 V 10% HIGH IMPEDANCE 1.3 V tPHL tPLH Q 1.3 V Q 10% VOL 90% VOH 1.3 V HIGH IMPEDANCE tTHL tTLH Figure 1. Figure 2. VALID 3V DATA 1.3 V GND tsu th 3V CLOCK 1.3 V GND Figure 3. TEST CIRCUITS TEST POINT TEST POINT OUTPUT DEVICE UNDER TEST DEVICE UNDER TEST CL* CONNECT TO VCC WHEN TESTING tPLZ AND tPZL CONNECT TO GND WHEN TESTING tPHZ AND tPZH 1 kW OUTPUT CL* *Includes all probe and jig capacitance *Includes all probe and jig capacitance Figure 4. Figure 5. EXPANDED LOGIC DIAGRAM D0 3 D1 4 D D Q C CLOCK D2 7 Q D3 8 D C Q D4 13 D C Q D5 14 D C Q D6 17 D C Q D7 18 D C Q D C Q C 11 OUTPUT 1 ENABLE 2 Q0 5 Q1 6 Q2 9 Q3 http://onsemi.com 5 12 Q4 15 Q5 16 Q6 19 Q7 MC74HCT374A PACKAGE DIMENSIONS PDIP-20 N SUFFIX CASE 738-03 ISSUE E NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. -A- 20 11 1 10 B L C -T- K SEATING PLANE M N E G F J D 20 PL 20 PL 0.25 (0.010) 0.25 (0.010) M T A M T B M DIM A B C D E F G J K L M N INCHES MIN MAX 1.010 1.070 0.240 0.260 0.150 0.180 0.015 0.022 0.050 BSC 0.050 0.070 0.100 BSC 0.008 0.015 0.110 0.140 0.300 BSC 0_ 15 _ 0.020 0.040 MILLIMETERS MIN MAX 25.66 27.17 6.10 6.60 3.81 4.57 0.39 0.55 1.27 BSC 1.27 1.77 2.54 BSC 0.21 0.38 2.80 3.55 7.62 BSC 0_ 15_ 0.51 1.01 M SOIC-20 DW SUFFIX CASE 751D-05 ISSUE G A 20 11 X 45 _ E h 1 10 20X B B 0.25 M T A S B S A L H M 10X 0.25 NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF B DIMENSION AT MAXIMUM MATERIAL CONDITION. q B M D 18X e A1 SEATING PLANE C T http://onsemi.com 6 DIM A A1 B C D E e H h L q MILLIMETERS MIN MAX 2.35 2.65 0.10 0.25 0.35 0.49 0.23 0.32 12.65 12.95 7.40 7.60 1.27 BSC 10.05 10.55 0.25 0.75 0.50 0.90 0_ 7_ MC74HCT374A PACKAGE DIMENSIONS TSSOP-20 DT SUFFIX CASE 948E-02 ISSUE C 20X 0.15 (0.006) T U 2X L K REF 0.10 (0.004) S L/2 20 M T U S V IIII IIII IIII K K1 S J J1 11 B -U- PIN 1 IDENT 1 SECTION N-N 0.25 (0.010) N 10 M 0.15 (0.006) T U S N A -V- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. F DETAIL E -W- C G D H DETAIL E 0.100 (0.004) -T- SEATING PLANE DIM A B C D F G H J J1 K K1 L M SOLDERING FOOTPRINT 7.06 1 0.65 PITCH 16X 0.36 16X 1.26 DIMENSIONS: MILLIMETERS http://onsemi.com 7 MILLIMETERS MIN MAX 6.40 6.60 4.30 4.50 --1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.27 0.37 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.252 0.260 0.169 0.177 --0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.011 0.015 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ MC74HCT374A PACKAGE DIMENSIONS SOEIAJ-20 F SUFFIX CASE 967-01 ISSUE A 20 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). LE 11 Q1 E HE 1 M_ L 10 DETAIL P Z D e VIEW P A A1 b 0.13 (0.005) c M 0.10 (0.004) DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --2.05 0.05 0.20 0.35 0.50 0.15 0.25 12.35 12.80 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 _ 0_ 0.70 0.90 --0.81 INCHES MIN MAX --0.081 0.002 0.008 0.014 0.020 0.006 0.010 0.486 0.504 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 _ 0_ 0.028 0.035 --0.032 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 8 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC74HCT374A/D