Type HB Series
Tyco Electronics is a leading
European supplier of standard and
custom designed high value/high
voltage resistors for high voltage,
industrial, control, medical and
general-purpose use.
The HB is a tough epoxy coated
high voltage resistor, with axial or
radial leads, values up to 1G Ohm
and an operational voltage to 20kV
as standard and 30kV to order.
The resistors are made from quality
materials for optimum reliability and
stability. Tyco Electronics can test
resistors to conform to relevant
international, MIL or customer
specifications.
Tyco Electronics is happy to advise
on the use of resistors for high
frequency applications and to
supply information for high voltage
use.
Key Features
I
Up to 15kV Element
Voltage
•Unique specification
for the most deman-
ding applications
I
High Ratio of Size
to Power
•The solution to your
PCB population
problems
I
1kW to 1GW
•Coupled with 1%
tolerance gives
ultimate design
flexibility
I
Established Product
with Proven Reliability
I
Low Inductance
•For the fastest
switching speeds
Applications
I
High Voltage
I
Voltage Divider
I
Surge
I
Filter
I
Balancing
I
Inrush Limiting
Characteristics -
Electrical
HBA HB1 HB3
Power Dissipation - Power @ 20°C (W): 0.8 2.0 4.0
@ 70°C: 0.4 1.0 2.0
Ohmic Value - Min (Ohms): 1K 10K 10K
Max: 120M 1G 1G
Resistance Tolerance (%) (Tighter By Request): 1%, 2%, 5% 1%, 2%, 5% 1%, 2%, 5%
Maximum Working Voltage - DC or ACrms (Volts): 1kV 7.5kV 15kV
Insulation Resistance - Epoxy Coated, @500V dc (Ohms): >106MΩ >106MΩ >106MΩ
Load Stability - 1000hr’s @ 70°C (%): ±0.5% ±0.5% ±0.5%
Temp. Rapid Change - -55°C to 125°C for 5 cycles (ΔR): ±0.1% ±0.1% ±0.1%
Endurance - 1000 Hours @ 200°C (ΔR): <=2% <=2% <=2%
Resistance to Soldering Heat - 350°C for 3.5seconds (ΔR): 0.05% 0.05% 0.05%
Temperature Coefficient (ppm/°C): ±100ppm/°C ±100ppm/°C ±100ppm/°C
(±20ppm/°C available to special order)
Voltage Coefficient:
Negligible up to 100K Negligible up to 200K
Increasing to 0.02ppm/Volt at 800K Increasing to
0.01ppm/Volt at 1M0
Increasing to 1.0ppm/Volt at 5M0 Increasing to
1.0ppm/Volt at 10M
Increasing to 2.0ppm/Volt at 50M Increasing to
2.0ppm/Volt at 100M
Increasing to 8.0ppm/Volt at 1000M Increasing to
8.0ppm/Volt at 1000M
Ambient Temperature Range (°C): -55 to 125 -55 to 125 -55 to 125
Long Term Damp Heat (%): 0.25% 0.25% 0.25%
(Steady state 56 Days 95% RH at 40°C)
Noise (Quantech) Dependent -20dB (0.1μ V/V) at lower values
on Resistor Type and Value: +10dB (3.3μ V/V) at higher values
Encapsulation: Epoxy coating (Optional)
Solvent Resistance: Print will withstand the action of all
commonly used industrial solvents.
Lead Material: Tinned copper wire
Lead Length: Minimum 20mm
Lead Diameter: Nominal 0.6 ± 0.05mm
Dimensions -
Type HBA, HB1 & HB3 (Radial) Type HB1 & HB3 (Axial)
Type A B C D E F G H I
HBA Uncoated 10.2 7 1.75 60.2 5.0 – – – –
Epoxy Coated 12.5 8 2.6 60.5 5.0 – – – –
HB1 Uncoated 8.4 26 1.5 33.8 22.9 26 66 1.5 8.4
Epoxy Coated 10.4 26.5 3.0 35.8 22.9 26.3 66 3 9.2
HB3 Uncoated 8.4 51.1 1.5 33.8 48.3 51.1 91.1 1.5 8.4
Epoxy Coated 10.4 52 3.0 35.8 48.3 53.5 91.1 3 9.6
F
G
I
D
B
E
C
A
High Value / High Voltage Resistors
Type HB Series
Literature No. 1773310
Issued: 01-10
Dimensions are shown for
reference purposes only.
Dimensions are in
millimetres unless
otherwise specified.
Specifications subject to
change.
tycoelectronics.com
passives.tycoelectronics.com