SURFACE MOUNT VOIDLESS-
HERMETICALLY-SEALED ULTRA FAST
RE
CO
VERY
G
LA
SS
RE
C
TIFIER
S
WWW.Microsemi .COM
SCOTTSDALE DIVISION
1N5807CBUS thru 1N5811CBUS
1N5807CBUS–1N5811CBUS
DESCRIPTION APPEARANCE
This “Ultrafast Recovery” surface mount rectifier diode series is military qualified to MIL-
PRF-19500/742 and is ideal for high-reliability applications where a failure cannot be
tolerated. These industry-recognized 6.0 Amp rated rectifiers for working peak reverse
voltages from 50 to 150 volts are hermetica ll y se aled with voidless-glass constructio n using
an internal “Category III” metallurgical bond. These devices are also available in axial-
leaded package configurations (see separate data sheet for 1N5807CB thru 1N5811CB).
Microsemi also offers numerous other rectifier products to meet higher and lower current
ratings with various recovery time speed requirements including standard, fast, and
ultrafast device types in both throu gh-hole and surface mount packages.
Package “E”
or D-5B
IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com
FEATURES APPLIC ATIONS / BENE FITS
• Surface mount package series equivalent to the JEDEC
registered 1N5807 to 1N5811 series
• Voidless-hermetically-sealed glass package
• Extremely robust construction
• Triple-layer passivation
• Internal “Category III” Metallurgical bonds
• JAN, JANTX, & JANTXV available per MIL-PRF-19500/7 42
• Further screening options are available for JANS in
accordance with MIL-PRF-19500/742 by using a “SP” prefix
• Axial-leaded e quivalents also availabl e (see separate data
sheet for 1N5807CB thru 1N5811CB)
• Ultrafast recovery 6 Amp rectifier series 50 to 150V
• Military and other high-reliability applications
• Switching power supplies or other applications
requiring extremely fast switching & low forward
loss
• High forward surge current capability
• Low thermal resistance
• Controlled avalanche with peak reverse power
capability
• Inherently radiation hard as described in Microsemi
MicroNote 050
MAXIMUM RAT ING S MECHANICAL AND PACKAGING
• Operating Temperature: -65oC to +175oC.
• Storage Temperature: -65oC to +175oC.
• Average Rectified For ward Current (IO): 6 Amps @ TEC
= 75ºC End Cap temperature (see note 1)
• Thermal Resistance: 6.5 ºC/W junction to e nd cap
• Thermal Impedance: 1.5 ºC/W @ 10 ms heating time
• Forward Surge Current (8.3 ms half sine) 125 Amps
• Capacitance: 60 pF at 10 volts, f = 1 MHz
• Solder temperature: 260ºC for 10 s (maximum)
• CASE: Hermetically sealed voidless hard glass
with Tungsten slugs
• TERMINALS: End caps are Copper with Tin/Lead
(Sn/Pb) finish.
• MARKING & POLARITY: Cathode band only
• Tape & Reel option: Standard per EIA-481-B
• Weight: 539 mg
• See package dimensions and recommended pad
layout on last page
ELECTRICAL CHARACTERISTICS
TYPE
WORKING
PEAK
REVERSE
VOLTAGE
VRWM
BREAKDOWN
VOLTAGE
(MIN.)
@ 100μA
VBR
AVERAGE
RECTIFIED
CURRENT
IO1
@TEC=75ºC
(Note 1)
AVERAGE
RECTIFIED
CURRENT
IO2
@TA=55ºC
(Note 2)
MAXIMUM
FORWARD
VOLTAGE
@ 4 A
(8.3 ms pulse)
VF
REVERSE
CURRENT
(MAX)
@ VRWM
IR
SURGE
CURRENT
(MAX)
IFSM
(NOTE 3)
REVERSE
RECOVERY
TIME (MAX)
(NOTE 4)
trr
VOLTS VOLTS AMPS AMPS VOLTS μA AMPS ns
25
oC 100oC25
oC 125oC
1N5807CBUS
1N5809CBUS
1N5811CBUS
50
100
150
60
110
160
6.0
6.0
6.0
3.0
3.0
3.0
0.875
0.875
0.875
0.800
0.800
0.800
5
5
5
525
525
525
125
125
125
30
30
30
NOTE 1: Rated at TEC = 75ºC. Derate at 60 mA/ºC for TEC above 75ºC
NOTE 2: Derate linearly at 25 mA/ºC above TA = 55ºC. This rating is typical for PC boards where thermal resistance from mounting point to
ambient is sufficiently controlled where TJ(max) does not exceed 175ºC
NOTE 3: TA = 25oC @ IO = 3.0 A and VRWM for ten 8.3 ms surges at 1 minute intervals
Microsemi
Scottsdale Division Page 1
NOTE 4: IF = 1.0 A, IRM = 1.0 A, IR(REC) = 0.10 A and di/dt = 100 A/µs min
Copyright © 2007
7-26-2007 8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503
SURFACE MOUNT VOIDLESS-
HERMETICALLY-SEALED ULTRA FAST
RE
CO
VERY
G
LA
SS
RE
C
TIFIER
S
WWW.Microsemi .COM
SCOTTSDALE DIVISION
1N5807CBUS thru 1N5811CBUS
1N5807CBUS–1N5811CBUS
SYMBOLS & DEFINITI ONS
Symbol Definition
VBR Minimum Breakdown Voltage: The minimum voltage the device will exhibit at a specified current.
VRWM Working Peak Reverse Voltage: The maxi mum peak voltage that can be applied over the operating
temperature range.
VF Maximum Forward Voltage: The maximum forward voltage the device will exhibit at a specified current.
IR Maximum Leakage Current: The maximum leakage current that will flow at the specified voltage a nd
temperature.
C Capacitance: The capacitance in pF at a frequency of 1 MHz and specified volta ge
trr
Reverse Recovery Time: The time interval between the instant the current passes through zero when
changing from the forward direction to the reverse direction and a specified recovery dec ay point after a peak
reverse current is reached.
GRAPHS
FIGURE 1 FIGURE 2
TYPICAL FORWARD CURRENT TYPICAL REVERSE CURRENT vs. VOLTAGE
vs. FORWARD VOLTAGE
FIGURE 3
FORWARD PULSE CURRENT vs. DURATION
Microsemi
Scottsdale Division Page 2
Copyright © 2007
7-26-2007 8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503
SURFACE MOUNT VOIDLESS-
HERMETICALLY-SEALED ULTRA FAST
RE
CO
VERY
G
LA
SS
RE
C
TIFIER
S
WWW.Microsemi .COM
SCOTTSDALE DIVISION
1N5807CBUS thru 1N5811CBUS
1N5807CBUS–1N5811CBUS
FIGURE 4
MULTIPLE SURGE CURRENT vs. DURATION
PACKAGE DIMENSIONS AND PAD LAYOUT
NOTE: This Package Outline has also previously PAD LAYOUT
been identified as “D-5B”
INCHES mm
A 0.288 7.32
B 0.070 1.78
C 0.155 3.94
Note: If mounting requires adhesive
separate from the solder, an additional
0.080 inch diameter contact may be
placed in the center between the pads
as an optional spot for cement.
INCHES mm
MIN MAX MIN MAX
BL .205 .225 5.21 5.72
BD .137 .142 3.48 3.61
ECT .019 .028 0.48 0.711
S .003 --- 0.08 ---
Microsemi
Scottsdale Division Page 3
Copyright © 2007
7-26-2007 8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503
