MC74VHC1G125 Noninverting 3-State Buffer Features * * * * * * * High Speed: tPD = 3.5 ns (Typ) at VCC = 5 V Low Power Dissipation: ICC = 1 mA (Max) at TA = 25C Power Down Protection Provided on Inputs Balanced Propagation Delays Pin and Function Compatible with Other Standard Logic Families Chip Complexity: FETs = 58; Equivalent Gates = 15 These Devices are Pb-Free and are RoHS Compliant OE 1 IN A 2 GND 3 5 VCC 4 OUT Y OE EN MARKING DIAGRAMS 5 5 1 SC-88A / SOT-353 / SC-70 DF SUFFIX CASE 419A W0 M G G 1 5 5 1 TSOP-5 / SOT-23 / SC-59 DT SUFFIX CASE 483 W0 M G G 1 W0 = Device Code M = Date Code* G = Pb-Free Package (Note: Microdot may be in either location) *Date Code orientation and/or position may vary depending upon manufacturing location. PIN ASSIGNMENT Figure 1. Pinout (Top View) IN A http://onsemi.com M The MC74VHC1G125 is an advanced high speed CMOS noninverting 3-state buffer fabricated with silicon gate CMOS technology. It achieves high speed operation similar to equivalent Bipolar Schottky TTL while maintaining CMOS low power dissipation. The internal circuit is composed of three stages, including a buffered 3-state output which provides high noise immunity and stable output. The MC74VHC1G125 input structure provides protection when voltages up to 7 V are applied, regardless of the supply voltage. This allows the MC74VHC1G125 to be used to interface 5 V circuits to 3 V circuits. 1 OE 2 IN A 3 GND 4 OUT Y 5 VCC FUNCTION TABLE OUT Y Figure 2. Logic Symbol A Input OE Input Y Output L H X L L H L H Z ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. (c) Semiconductor Components Industries, LLC, 2011 May, 2011 - Rev. 16 1 Publication Order Number: MC74VHC1G125/D MC74VHC1G125 MAXIMUM RATINGS Symbol Value Unit VCC DC Supply Voltage Characteristics -0.5 to +7.0 V VIN DC Input Voltage -0.5 to +7.0 V -0.5 to 7.0 -0.5 to VCC + 0.5 V -20 mA +20 mA +25 mA VOUT DC Output Voltage VCC = 0 High or Low State IIK Input Diode Current IOK Output Diode Current IOUT DC Output Current, per Pin ICC DC Supply Current, VCC and GND PD Power Dissipation in Still Air qJA Thermal Resistance TL VOUT < GND; VOUT > VCC +50 mA SC-88A, TSOP-5 200 mW SC-88A, TSOP-5 333 C/W Lead Temperature, 1 mm from Case for 10 secs 260 C TJ Junction Temperature Under Bias +150 C Tstg Storage Temperature -65 to +150 C Human Body Model (Note 1) Machine Model (Note 2) Charged Device Model (Note 3) > 2000 > 200 N/A V Above VCC and Below GND at 125C (Note 4) $500 mA VESD ESD Withstand Voltage ILatchup Latchup Performance Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Tested to EIA/JESD22-A114-A. 2. Tested to EIA/JESD22-A115-A. 3. Tested to JESD22-C101-A. 4. Tested to EIA/JESD78. RECOMMENDED OPERATING CONDITIONS Symbol Characteristics Min Max Unit VCC DC Supply Voltage 2.0 5.5 V VIN DC Input Voltage 0.0 5.5 V VOUT TA tr , tf DC Output Voltage 0.0 VCC V Operating Temperature Range -55 +125 C 0 0 100 20 ns/V Input Rise and Fall Time VCC = 3.3 V $ 0.3 V VCC = 5.0 V $ 0.5 V 90 419,300 47.9 100 178,700 20.4 110 79,600 9.4 120 37,000 4.2 130 17,800 2.0 140 8,900 1.0 TJ = 80 C 117.8 TJ = 90 C 1,032,200 TJ = 100 C 80 FAILURE RATE OF PLASTIC = CERAMIC UNTIL INTERMETALLICS OCCUR TJ = 110 C Time, Years TJ = 120 C Time, Hours TJ = 130 C Junction Temperature C NORMALIZED FAILURE RATE Device Junction Temperature versus Time to 0.1% Bond Failures 1 1 10 100 1000 TIME, YEARS Figure 3. Failure Rate vs. Time Junction Temperature http://onsemi.com 2 MC74VHC1G125 DC ELECTRICAL CHARACTERISTICS Symbol Parameter Test Conditions Min 1.5 2.1 3.15 3.85 VIH Minimum High-Level Input Voltage 2.0 3.0 4.5 5.5 VIL Maximum Low-Level Input Voltage 2.0 3.0 4.5 5.5 VOH Minimum High-Level Output Voltage VIN = VIH or VIL VOL Maximum Low-Level Output Voltage VIN = VIH or VIL TA = 25C VCC (V) Typ TA 85C Max Min 1.5 2.1 3.15 3.85 0.5 0.9 1.35 1.65 VIN = VIH or VIL IOH = -50 mA 2.0 3.0 4.5 1.9 2.9 4.4 VIN = VIH or VIL IOH = -4 mA IOH = -8 mA 3.0 4.5 2.58 3.94 VIN = VIH or VIL IOL = 50 mA 2.0 3.0 4.5 VIN = VIH or VIL IOL = 4 mA IOL = 8 mA Max 2.0 3.0 4.5 0.0 0.0 0.0 -55 TA 125C Min Max 1.5 2.1 3.15 3.85 0.5 0.9 1.35 1.65 V 0.5 0.9 1.35 1.65 1.9 2.9 4.4 1.9 2.9 4.4 2.48 3.80 2.34 3.66 Unit V V V 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 0.36 0.36 0.44 0.44 0.52 0.52 V V IOZ Maximum 3-State Leakage Current VIN = VIH or VIL VOUT = VCC or GND 5.5 0.2 5 $2.5 $2.5 mA IIN Maximum Input Leakage Current VIN = 5.5 V or GND 0 to 5.5 0.1 1.0 $1.0 mA ICC Maximum Quiescent Supply Current VIN = VCC or GND 5.5 1.0 20 40 mA IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIII IIII IIIIII IIIIIIII IIIIII IIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIII IIIIIIII III III III II III III IIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIII IIIIIIII III III III II III III IIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII AC ELECTRICAL CHARACTERISTICS Cload = 50 pF, Input tr = tf = 3.0 ns TA = 25C Symbol tPLH, tPHL tPZL, tPZH tPLZ, tPHZ CIN COUT Typ Max Max Unit VCC = 3.3 0.3 V CL = 15 pF CL = 50 pF 4.5 6.4 8.0 11.5 9.5 13.0 12.0 16.0 ns VCC = 5.0 0.5 V CL = 15 pF CL = 50 pF 3.5 4.5 5.5 7.5 6.5 8.5 8.5 10.5 Maximum Output Enable Time, Input OE to Y (Figures 4 and 5) VCC = 3.3 0.3 V RL = 1000 W CL = 15 pF CL = 50 pF 4.5 6.4 8.0 11.5 9.5 13.0 11.5 15.0 VCC = 5.0 0.5 V RL = 1000 W CL = 15 pF CL = 50 pF 3.5 4.5 5.1 7.1 6.0 8.0 8.5 10.5 Maximum Output Disable Time, Input OE to Y (Figures 4 and 5) VCC = 3.3 0.3 V RL 1000 W CL = 15 pF CL = 50 pF 6.5 8.0 9.7 13.2 11.5 15.0 14.5 18.0 VCC = 5.0 0.5 V RL = 1000 W CL = 15 pF CL = 50 pF 4.8 7.0 6.8 8.8 8.0 10.0 10.0 12.0 Maximum Input Capacitance 4.0 10 10 10 Maximum 3-State Output Capacitance (Output in High Impedance State) 6.0 Test Conditions Min Max -55 TA 125C Maximum Propagation Delay, Input A to Y (Figures 3 and 4) Parameter Min TA 85C Min ns ns pF pF Typical @ 25C, VCC = 5.0 V CPD 8.0 Power Dissipation Capacitance (Note 5) pF 5. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no-load dynamic power consumption; PD = CPD VCC2 fin + ICC VCC. http://onsemi.com 3 MC74VHC1G125 SWITCHING WAVEFORMS VCC OE 50% GND tPZL VCC 50% GND tPZH tPHL tPLH HIGH IMPEDANCE 50% VCC Y A tPLZ VOL + 0.3V tPHZ VOH - 0.3V 50% VCC 50% VCC Y HIGH IMPEDANCE Y Figure 4. Switching Wave Forms Figure 5. TEST POINT TEST POINT OUTPUT DEVICE UNDER TEST DEVICE UNDER TEST CL* *Includes all probe and jig capacitance OUTPUT 1 kW CL * CONNECT TO VCC WHEN TESTING tPLZ AND tPZL. CONNECT TO GND WHEN TESTING tPHZ AND tPZH. *Includes all probe and jig capacitance Figure 6. Test Circuit Figure 7. Test Circuit INPUT Figure 8. Input Equivalent Circuit ORDERING INFORMATION Device Package M74VHC1G125DFT1G SC-88A/SOT-353/SC-70 (Pb-Free) M74VHC1G125DFT2G TSC-88A/SOT-353/SC-70 (Pb-Free) M74VHC1G125DTT1G TSOP-5/SOT-23/SC-59 (Pb-Free) Shipping 3000 Units / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 4 MC74VHC1G125 PACKAGE DIMENSIONS SC-88A (SC-70-5/SOT-353) CASE 419A-02 ISSUE K A NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419A-01 OBSOLETE. NEW STANDARD 419A-02. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. G 5 4 -B- S 1 2 DIM A B C D G H J K N S 3 D 5 PL 0.2 (0.008) M B M N J C H K http://onsemi.com 5 INCHES MIN MAX 0.071 0.087 0.045 0.053 0.031 0.043 0.004 0.012 0.026 BSC --0.004 0.004 0.010 0.004 0.012 0.008 REF 0.079 0.087 MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.10 0.10 0.30 0.65 BSC --0.10 0.10 0.25 0.10 0.30 0.20 REF 2.00 2.20 MC74VHC1G125 PACKAGE DIMENSIONS TSOP-5 CASE 483-02 ISSUE H D 5X NOTE 5 2X 0.10 T 2X 0.20 T NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. 5. OPTIONAL CONSTRUCTION: AN ADDITIONAL TRIMMED LEAD IS ALLOWED IN THIS LOCATION. TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2 FROM BODY. 0.20 C A B M 5 1 4 2 L 3 B S K DETAIL Z G A DIM A B C D G H J K L M S DETAIL Z J C 0.05 SEATING PLANE H T MILLIMETERS MIN MAX 3.00 BSC 1.50 BSC 0.90 1.10 0.25 0.50 0.95 BSC 0.01 0.10 0.10 0.26 0.20 0.60 1.25 1.55 0_ 10 _ 2.50 3.00 SOLDERING FOOTPRINT* 0.95 0.037 1.9 0.074 2.4 0.094 1.0 0.039 0.7 0.028 SCALE 10:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 6 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC74VHC1G125/D