General-purpose Operational Amplifiers / Comparators TROPHY SERIES Operational Amplifiers LM358DR/PWR/DGKR,LM2904DR/PWR/DGKR/VQDR/VQPWR LM324DR/PWR/KDR,LM2902DR/PER/KDR/KPWR/KVQDR/KVQPWR Description The Universal Standard family LM358 / 324 and LM2904 / 2902 monolithic ICs integrate two independent op-amp circuits and phase compensation capacitors on a single chip, feature high gain and low power consumption, and possess an operating voltage range between 3[V]and 32[V] (single power supply.) No.11094EBT02 TROPHY SERIES Dual Quad LM358 family LM2904 family LM324 family LM2902 family LM358DR LM358PWR LM358DGKR LM2904DR LM2904PWR LM2904DGKR LM2904VQDR LM2904VQPWR LM324DR LM324PWR LM324KDR LM2902DR LM2902PWR LM2902KDR LM2902KPWR LM2902KVQDR LM2902KVQPWR Features 1) Operating temperature range 0[] to + 70[] Commercial Grade LM358/324 family : Extended Industrial Grade LM2904/2902 family : -40[] to +125[] 2) Wide operating voltage range +3[V] to +32[V] (single supply) 1.5[V] to 16[V] (dual supply) 3) Low supply current 4) Common-mode input voltage range, including ground 5) Differential input voltage range equal to maximum ratedsupply voltage 6) High large signal voltage gain 7) Wide output voltage range Pin Assignment 1OUT 1IN1IN+ GND 1 2 3 4 8 Vcc 7 2OUT 6 5 SOIC8 TSSOP8 LM358DR LM2904DR LM2904VQDR LM358PWR LM2904PWR LM2904VQPWR www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 2IN- 1OUT 1 14 4OUT 1IN- 2 13 4IN- 1IN+ 3 12 4IN+ Vcc 4 11 GND 2IN+ 5 10 3IN+ 2IN- 6 9 3IN- 2OUT 7 8 3OUT 2IN+ MSOP8/VSSOP8 LM358DGKR LM2904DGKR SOIC14 LM324DR LM324KDR LM2902DR LM2902KDR LM2902KVQDR 1/17 TSSOP14 LM324PWR LM2902PWR LM2902KPWR LM2902KVQPWR 2011.06 - Rev.B LM358DR/PWR/DGKR,LM2904DR/PWR/DGKR/VQDR/VQPWR LM324DR/PWR/KDR,LM2902DR/PER/KDR/KPWR/KVQDR/KVQPWR Technical Note Absolute Maximum Ratings (Ta=25[]) Parameter Symbol Supply Voltage LM358 family Vcc-GND Operating Temperature Range Topr Storage Temperature Range Tstg Input Common-mode Voltage VICM Maximum Junction Temperature Tjmax Ratings LM2904 LM2902 family family +26 LM324 family +32 0 to +70 LM2904V LM2902V family family +32 -40 to +125 V -65 to +150 -0.3 to +32 Unit -0.3 to +26 -0.3 to +32 V 150 Electric Characteristics LM358,LM324 family (Unless otherwise specified, Vcc=+5[V]) Limits Parameter Symbol Input Offset Voltage (*1) VIO Input Offset Voltage Drift VIO Input Offset Current (*1) IIO Input Offset Current Drift Input Bias Current (*1) IIO IIB Input Common-modeVoltage Range VICR High Level Output Voltage VOH Temperature range LM358 family LM324 family Unit Min. Typ. Max. Min. Typ. Max. 25 3 7 3 7 Full range 9 9 7 25 2 50 2 50 Full range 150 150 10 25 20 250 20 250 Full range 500 500 25 0 Vcc-1.5 Vcc-1.5 Full range 0 Vcc-2.0 Vcc-2.0 25 Vcc-1.5 Vcc-1.5 Full range 27 28 27 28 mV Conditions VO=1.4[V] VIC=VICR(min) Vcc=5[V] to 30[V] V/ nA VO=1.4[V] Fig. No 98 98 pA/ nA VO=1.4[V] 98 V Vcc=5[V] to 30[V] 98 V RL2[k] 99 Vcc=30[V],RL10[k] Low Level Output Voltage VOL Full range 5 20 5 20 Large Signal Voltage Gain AVD 25 25 100 25 100 Common-mode Rejection Ratio CMRR 25 65 80 65 80 dB Vcc=5[V] to 30[V], VIC=VICR(min) 98 Supply-Voltage rejection ratio KSVR 25 65 100 65 100 dB Vcc=5[V] to 30[V] 98 VO1/VO2 25 120 120 dB f=1[kHz] to 20[kHz] 101 25 20 30 20 30 Full range 10 10 mA Vcc=15[V],VO=0[V] VID=1[V] mA Vcc=15[V],VO=0[V] VID=-1[V] A VO=200[mV],VID=-1[V] Cross-talk Attenuation Source Output Current (*2) Sink 25 10 20 10 20 Full range 2 2 25 12 30 12 30 Full range 0.7 1.2 0.7 1.2 Full range 1 2 1.4 3 SR 25 0.3 0.5 Unity Gain Bandwidth B1 25 0.7 1.2 Equivalent Input Noise Voltage Vn 25 40 35 Supply Current (All Amps) ICC Slew Rate at Unity-Gain mV RL10[k] Vcc=15[V] V/mV VO=1[V] to 11[V] RL2[k] 98 98 99 VO=2.5[V],No Load mA Vcc=30[V],VO=0.5[V] No Load RL=1[M],CL=30[pF] VI=10[V] V/s Vcc=15[V],GND=-15[V] (reference to Fig100) RL=1[M],CL=20[pF] MHz Vcc=15[V],GND=-15[V] (reference to Fig99) Vcc=15[V],GND=-15[V] nV/ Hz RS=100[],VI=0[V] f=1[kHz](reference to Fig99) 99 99 99 99 (*1) Absolute value (*2) Under high temperature, consider the power dissipation of IC when selecting the output current. When the output terminal is continuously shorted, the output current reduces the temperature inside the IC by flushing. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 2/17 2011.06 - Rev.B LM358DR/PWR/DGKR,LM2904DR/PWR/DGKR/VQDR/VQPWR LM324DR/PWR/KDR,LM2902DR/PER/KDR/KPWR/KVQDR/KVQPWR Technical Note LM2904,LM2902 family (Unless otherwise specified, Vcc=+5[V]) Limits Parameter Symbol Temperature range LM2904 family Min. Input Offset Voltage (*3) VIO Input Offset Voltage Drift VIO LM2904 LM2902(*5) Input Offset Current (*3) IIO LM2904V LM2902V(*5) Input Offset Current Drift Input Bias Current (*3) IIB Input Common-mode Voltage Range High Level IIO VICR Output Voltage LM2904 LM2902(*5) LM2904V LM2902V(*5) VOH Typ. LM2902 family Max. Min. Typ. Unit 25 3 7 3 7 Full range 10 10 7 7 25 2 50 2 50 Full range 300 300 25 2 50 2 50 Full range 150 150 10 10 25 20 250 20 250 Full range 500 500 25 Vcc-1.5 Vcc-1.5 Full range Vcc-2.0 Vcc-2.0 25 Vcc-1.5 Vcc-1.5 Full range 23 24 23 24 Full range 27 28 27 mV nA 98 RL10[k] V mV Large Signal Voltage Gain AVD 25 25 100 25 100 V/mV 25 50 80 50 80 dB 25 65 80 60 80 dB 65 100 50 100 60 100 120 120 Output Current (*4) Sink LM2904 LM2902(*5) LM2904V LM2902V(*5) 20 30 20 30 60 10 10 ICC Slew Rate at Unity Gain 99 RL10[k] 99 Vcc=15[V],VO=1[V] to 11[V] RL2[k] 98 Vcc=5[V] to MAX(*5) VIC=VICR(min) 98 dB Vcc=5[V] to MAX(*5) 98 dB f=1[kHz] to 20[kHz] 101 mA Vcc=15[V],VO=0[V] VID=1[V] mA Vcc=15[V],VO=0[V] VID=-1[V] 25 10 20 10 20 Full range 2 2 25 30 30 A 25 12 40 12 40 A Full range 0.7 1.2 0.7 1.2 Io Supply Current (All Amps) Vcc=MAX(*5),RL10[k] Vcc=MAX(*5),RL10[k] 20 25 Vcc=5[V] to MAX(*5) 5 Full range V Source 98 98 20 25 VO=1.4[V] 5 VO1/VO2 VO=1.4[V] 98 nA Cross-talk Attenuation pA/ Full range LM2902V(*5) VO=1.4[V],VIC=VICR(min) Vcc=5[V] to MAX(*5) V/ VOL 25 Fig. No Max. Low Level Output Voltage LM2904 LM2902(*5) CommonCMRR mode Rejection Ratio LM2904V LM2902V(*5) LM2904 LM2904V Supply Voltage KSVR M2902(*5) Rejection Ratio Conditions 99 VO=200[mV],VID=-1[V] Full range 1 2 1.4 3 SR 25 0.3 0.5 Unity-Gain Bandwidth B1 25 0.7 1.2 Equivalent Input Noise Voltage Vn 25 40 35 VO=2.5[V],No Load mA Vcc=MAX(*5),VO=0.5[V] No Load RL=1[M],CL=30[pF], VI=10[V] V/s Vcc=15[V],GND=-15[V] (reference to Fig100) RL=1[M],CL=20[pF] MHz Vcc=15[V],GND=-15[V] (reference to Fig99) Vcc=15[V],GND=-15[V] RS=100[]VI=0[V] nV/ Hz f=1[kHz], ( reference to Fig99) 99 99 99 99 (*3) Absolute value (*4) Under high temperature, consider the power dissipation of the IC when selecting the output current. When the output terminal is continuously shorted the output current is reduced to lower the temperature inside the IC. (*5) The maximum supply voltage is 26V for the LM2904DR, LM2904PW, LM2904PWR, and LM2904DQKR The maximum supply voltage is 32V for the LM2904VQDR and LM2904VQPWR www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 3/17 2011.06 - Rev.B LM358DR/PWR/DGKR,LM2904DR/PWR/DGKR/VQDR/VQPWR LM324DR/PWR/KDR,LM2902DR/PER/KDR/KPWR/KVQDR/KVQPWR Technical Note Reference Data LM358 family POWER DISSIPATION Pd [mW] LM358 family LM358 family LM358 family 800 LM358PWR LM358DGKR 600 25 LM358DR 32V 0 400 200 5V 70 3V 0 70 0 25 50 75 100 AMBIENT TEMPERATURE : [] Ta [] Fig. 1 Derating Curve Fig. 2 Supply Current - Supply Voltage LM358 family Fig. 3 Supply Current - Ambient Temperature LM358 family LM358 family 0 0 25 70 25 70 Fig. 4 Maximum Output Voltage - Supply Voltage (RL=10[k]) Fig. 5 Fig. 6 Maximum Output Voltage - Ambient Temperature Output Source Current - Output Voltage (VCC=5[V],RL=2[k]) (VCC=5[V]) LM358 family LM358 family LM358 family 15V 70 3V 5V 0 3V 5V 15V 25 Fig. 7 Output Source Current - Ambient Temperature (VOUT=0[V]) Fig. 8 Output Sink Current - Output Voltage (VCC=5[V]) Fig. 9 Output Sink Current - Ambient Temperature (VOUT=VCC) LM358 family LM358 family LM358 family 32V 25 0 0 5V 25 3V 70 70 Fig. 10 Low Level Sink Current - Supply Voltage (VOUT=0.2[V]) Fig. 11 Low Level Sink Current - Ambient Temperature (VOUT=0.2[V]) Fig. 12 Input Offset Voltage - Supply Voltage (Vicm=0[V], VOUT=1.4[V]) (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 4/17 2011.06 - Rev.B LM358DR/PWR/DGKR,LM2904DR/PWR/DGKR/VQDR/VQPWR LM324DR/PWR/KDR,LM2902DR/PER/KDR/KPWR/KVQDR/KVQPWR Technical Note Reference Data LM358 family LM358 family LM358 family LM358 family 3V 5V 32V 25 0 32V 3V 5V 70 Fig. 13 Input Offset Voltage - Ambient Temperature (Vicm=0[V], VOUT=1.4[V]) Fig. 14 Input Bias Current - Supply Voltage (Vicm=0[V], VOUT=1.4[V]) Fig. 15 Input Bias Current - Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) LM358 family LM358 family LM358 family 70 0 25 0 25 70 [V] Fig. 16 Input Bias Current - Ambient Temperature (VCC=30[V],Vicm=28[V],VOUT=1.4[V]) Fig. 17 Input Offset Voltage - Common Mode Input Voltage (VCC=5[V]) Fig. 18 Input Offset Current - Supply Voltage (Vicm=0[V],VOUT=1.4[V]) LM358 family LM358 family LM358 family 0 15V 25 3V 5V 5V 32V 70 Fig. 19 Input Offset Current - Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) Fig. 20 Large Signal Voltage Gain - Supply Voltage (RL=2[k]) LM358 family LM358 family 36V 0 Fig. 21 Large Signal Voltage Gain - Ambient Temperature (RL=2[k]) LM358 family 32V 25 70 Fig. 22 Common Mode Rejection Ratio - Supply Voltage 5V 3V Fig. 23 Common Mode Rejection Ratio - Ambient Temperature Fig. 24 Power Supply Rejection Ratio - Ambient Temperature (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 5/17 2011.06 - Rev.B LM358DR/PWR/DGKR,LM2904DR/PWR/DGKR/VQDR/VQPWR LM324DR/PWR/KDR,LM2902DR/PER/KDR/KPWR/KVQDR/KVQPWR Technical Note Reference Data LM324 family BA2904 family LM324 family LM324 family family BA2904 LM324 family 1000 POWER DISSIPATION Pd [mW] LM324PWR LM324DR LM324KDR 800 32V 25 600 0 400 5V 200 70 3V 0 0 25 70 50 75 100 AMBIENT TEMPERATURE :[] Ta [] Fig. 25 Derating Curve Fig. 26 Supply Current - Supply Voltage LM324 family Fig. 27 Supply Current - Ambient Temperature LM324 family LM324 family 0 0 25 70 25 70 Fig. 28 Maximum Output Voltage - Supply Voltage (RL=10[k]) Fig. 29 Fig. 30 Maximum Output Voltage - Ambient Temperature Output Source Current - Output Voltage (VCC=5[V],RL=2[k]) (VCC=5[V]) LM324 family LM324 family LM324 family 15V 70 3V 5V 0 5V 15V 3V 25 Fig. 31 Output Source Current - Ambient Temperature (VOUT=0[V]) Fig. 32 Output Sink Current - Output Voltage (VCC=5[V]) Fig. 33 Output Sink Current - Ambient Temperature (VOUT=VCC) LM324 family LM324 family LM324 family 32V 0 25 0 25 5V 3V 70 70 Fig. 34 Low Level Sink Current - Supply Voltage (VOUT=0.2[V]) Fig. 35 Low Level Sink Current - Ambient Temperature (VOUT=0.2[V]) Fig. 36 Input Offset Voltage - Supply Voltage (Vicm=0[V], VOUT=1.4[V]) (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 6/17 2011.06 - Rev.B LM358DR/PWR/DGKR,LM2904DR/PWR/DGKR/VQDR/VQPWR LM324DR/PWR/KDR,LM2902DR/PER/KDR/KPWR/KVQDR/KVQPWR Technical Note Reference Data LM324 family LM324 family 3V 25 0 5V LM324 family LM324 family 32V 32V 3V 5V 70 Fig. 37 Input Offset Voltage - Ambient Temperature (Vicm=0[V], VOUT=1.4[V]) Fig. 38 Input Bias Current - Supply Voltage (Vicm=0[V], VOUT=1.4[V]) Fig. 39 Input Bias Current - Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) LM324 family LM324 family LM324 family 0 70 25 0 25 70 [V] Fig. 40 Input Bias Current - Ambient Temperature (VCC=30[V],Vicm=28[V],VOUT=1.4[V]) Fig. 41 Input Offset Voltage - Common Mode Input Voltage (VCC=5[V]) Fig. 42 Input Offset Current - Supply Voltage (Vicm=0[V],VOUT=1.4[V]) LM324 family LM324 family LM324 family 25 0 15V 3V 5V 5V 32V 70 Fig. 43 Input Offset Current - Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) Fig. 44 Large Signal Voltage Gain - Supply Voltage (RL=2[k]) LM324 family LM324 family 36V 0 Fig. 45 Large Signal Voltage Gain - Ambient Temperature (RL=2[k]) LM324 family 32V 25 5V 70 Fig. 46 Common Mode Rejection Ratio - Supply Voltage 3V Fig. 47 Common Mode Rejection Ratio - Ambient Temperature Fig. 48 Power Supply Rejection Ratio - Ambient Temperature (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 7/17 2011.06 - Rev.B LM358DR/PWR/DGKR,LM2904DR/PWR/DGKR/VQDR/VQPWR LM324DR/PWR/KDR,LM2902DR/PER/KDR/KPWR/KVQDR/KVQPWR Technical Note Reference Data LM2904 family LM2904 family family BA2904 BA2904 LM2904 family family LM2904 family 800 1.0 1.0 0.8 0.8 LM2904DR LM2904VQDR 400 200 SUPPLY CURRENT [mA] LM2904DGKR 600 SUPPLY CURRENT [mA] POWER DISSIPATION Pd [mW] LM2904PWR LM2904VQPWR 25 40 0.6 0.4 0 125 105 0.2 25 50 75 100 125 5V 3V 0.0 0 150 0.4 0.2 0.0 0 32V 0.6 10 AMBIENT TEMPERATURE : [] Ta [] Fig. 49 Derating Curve 20 30 SUPPLY VOLTAGE [V] -50 40 Fig. 50 Supply Current - Supply Voltage LM2904 family 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 51 Supply Current - Ambient Temperature LM2904 family LM2904 family 40 -25 50 5 -40 30 125 20 25 105 10 0 4 3 2 1 10 20 30 40 25 30 105 20 10 Fig. 52 Maximum Output Voltage - Supply Voltage (RL=10[k]) 125 0 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] SUPPLY VOLTAGE [V] 0 1 LM2904 family LM2904 family 30 15V 5V 30 15V 20 10 0 OUTPUT SINK CURRENT [mA] OUTPUT SINK CURRENT [mA] 3V 10 125 1 -40 0.1 25 0.01 0 25 50 75 100 125 150 0 0.4 AMBIENT TEMPERATURE [] Fig. 55 Output Source Current - Ambient Temperature (VOUT=0[V]) 0.8 1.2 1.6 OUTPUT VOLTAGE [V] 50 40 125 105 20 10 50 75 100 125 150 Fig. 57 Output Sink Current - Ambient Temperature (VOUT=VCC) LM2904 family 8 70 60 5V 50 40 3V 30 20 10 0 0 5 25 LM2904 family LOW LEVEL SINK CURRENT [A] 60 0 0 32V 25 30 -25 AMBIENT TEMPERATURE [] 80 -40 70 3V 10 -50 Fig. 56 Output Sink Current - Output Voltage (VCC=5[V]) LM2904 family 80 5V 2 INPUT OFFSET VOLTAGE [mV] -25 20 0 0.001 -50 5 LM2904 family 100 105 40 2 3 4 OUTPUT VOLTAGE [V] Fig. 53 Fig. 54 Maximum Output Voltage - Ambient Temperature Output Source Current - Output Voltage (VCC=5[V],RL=2[k]) (VCC=5[V]) 50 LOW LEVEL SINK CURRENT [A] 40 0 0 OUTPUT SOURCE CURRENT [mA] OUTPUT SOURCE CURRENT [mA] MAXIMUM OUTPUT VOLTAGE [V] MAXIMUM OUTPUT VOLTAGE [V] -40 10 15 20 25 SUPPLY VOLTAGE [V] 30 35 Fig. 58 Low Level Sink Current - Supply Voltage (VOUT=0.2[V]) 6 -40 25 4 2 0 -2 105 125 -4 -6 -8 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 59 Low Level Sink Current - Ambient Temperature (VOUT=0.2[V]) 0 5 10 15 20 25 SUPPLY VOLTAGE [V] 30 35 Fig. 60 Input Offset Voltage - Supply Voltage (Vicm=0[V], VOUT=1.4[V]) (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 8/17 2011.06 - Rev.B LM358DR/PWR/DGKR,LM2904DR/PWR/DGKR/VQDR/VQPWR LM324DR/PWR/KDR,LM2902DR/PER/KDR/KPWR/KVQDR/KVQPWR Technical Note Reference Data LM2904 family LM2904 family 8 LM2904 family 50 3V 2 0 5V -2 32V -4 40 30 20 10 105 -6 20 3V 10 5V 0 0 0 25 50 75 0 100 125 150 Fig. 61 Input Offset Voltage - Ambient Temperature (Vicm=0[V], VOUT=1.4[V]) 30 20 10 0 30 -50 35 -10 6 -40 4 105 25 125 2 0 -2 -4 -6 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 64 Input Bias Current - Ambient Temperature (VCC=30[V],Vicm=28[V],VOUT=1.4[V]) 3V 0 5V 32V -5 0 1 2 3 [V] INPUT VOLTAGE [Vin] -10 4 0 0 25 50 75 130 -40 25 120 110 100 90 105 125 80 70 100 125 150 AMBIENT TEMPERATURE [] Fig. 67 Input Offset Current - Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) -40 25 100 80 125 105 60 40 0 10 20 30 SUPPLY VOLTAGE [V] Fig. 70 Common Mode Rejection Ratio - Supply Voltage 40 15 20 25 30 35 Fig. 66 Input Offset Current - Supply Voltage (Vicm=0[V],VOUT=1.4[V]) LM2904 family 130 15V 120 110 100 5V 90 80 70 6 8 10 12 SUPPLY VOLTAGE [V] 14 -50 16 Fig. 68 Large Signal Voltage Gain - Supply Voltage (RL=2[k]) COMMON MODE REJECTION RATIO [dB] 120 10 SUPPLY VOLTAGE [V] 60 4 LM2904 family 140 5 140 LM2904 family 140 36V 32V 120 100 80 5V 3V 60 40 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 71 Common Mode Rejection Ratio - Ambient Temperature -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 69 Large Signal Voltage Gain - Ambient Temperature (RL=2[k]) LM2904 family 140 POWER SUPPLY REJECTION RATIO [dB] -25 125 105 -5 5 60 -50 0 LM2904 family 140 LARGE SIGNAL VOLTAGE GAIN [dB] 5 25 -40 Fig. 65 Input Offset Voltage - Common Mode Input Voltage (VCC=5[V]) LM2904 family 10 5 -10 -1 LARGE SIGNAL VOLTAGE GAIN [dB] -25 LM2904 family 10 -8 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 63 Input Bias Current - Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) LM2904 family 8 INPUT OFFSET VOLTAGE [mV] 40 10 15 20 25 SUPPLY VOLTAGE [V] Fig. 62 Input Bias Current - Supply Voltage (Vicm=0[V], VOUT=1.4[V]) LM2904 family 50 5 INPUT OFFSET CURRENT [nA] -25 AMBIENT TEMPERATURE [] INPUT BIAS CURRENT[nA] 32V 30 125 -50 INPUT OFFSET CURRENT [nA] 25 -40 40 INPUT BIAS CURRENT [nA] 4 INPUT BIAS CURRENT [nA] INPUT OFFSET VOLTAGE [mV] 6 -8 COMMON MODE REJECTION RATIO [dB] LM2904 family 50 130 120 110 100 90 80 70 60 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 72 Power Supply Rejection Ratio - Ambient Temperature (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 9/17 2011.06 - Rev.B LM358DR/PWR/DGKR,LM2904DR/PWR/DGKR/VQDR/VQPWR LM324DR/PWR/KDR,LM2902DR/PER/KDR/KPWR/KVQDR/KVQPWR Technical Note Reference Data LM2902 family 600 400 LM2902DR LM2902KDR LM2902KVQDR 200 1.0 1.0 0.8 0.8 SUPPLY CURRENT [mA] LM2902PWR LM2902KPWR LM2902KVQPWR 800 SUPPLY CURRENT [mA] POWER DISSIPATION Pd [mW] LM2902 family LM2902 family 1000 25 40 0.6 0.4 0.2 0 125 105 25 50 75 100 125 0.4 5V 3V 0.0 0 150 32V 0.6 0.2 0.0 0 LM2902 family 10 AMBIENT TEMPERATURE : [] Ta [] Fig. 73 Derating Curve 20 30 SUPPLY VOLTAGE [V] -50 40 Fig. 74 Supply Current - Supply Voltage LM2902 family 40 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 75 Supply Current - Ambient Temperature LM2902 family 5 -25 LM2902 family 50 -40 30 125 25 20 105 10 0 4 3 2 1 10 20 30 40 25 30 105 20 Fig. 76 Maximum Output Voltage - Supply Voltage (RL=10[k]) 125 10 0 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] SUPPLY VOLTAGE [V] 0 1 LM2902 family LM2902 family 30 15V 5V 30 15V 20 10 0 OUTPUT SINK CURRENT [mA] OUTPUT SINK CURRENT [mA] 3V 10 125 1 -40 0.1 25 0.01 0 25 50 75 100 125 150 0 0.4 AMBIENT TEMPERATURE [] Fig. 79 Output Source Current - Ambient Temperature (VOUT=0[V]) 0.8 1.2 1.6 OUTPUT VOLTAGE [V] 50 40 125 20 10 5 50 75 100 125 150 Fig. 81 Output Sink Current - Ambient Temperature (VOUT=VCC) LM2902 family 8 70 60 5V 50 40 3V 30 20 10 0 0 0 25 LM2902 family LOW LEVEL SINK CURRENT [A] 60 30 0 32V 25 105 -25 AMBIENT TEMPERATURE [] 80 -40 70 3V 10 -50 Fig. 80 Output Sink Current - Output Voltage (VCC=5[V]) LM2902 family 80 5V 2 INPUT OFFSET VOLTAGE [mV] -25 20 0 0.001 -50 5 LM2902 family 100 105 40 2 3 4 OUTPUT VOLTAGE [V] Fig. 77 Fig. 78 Maximum Output Voltage - Ambient Temperature Output Source Current - Output Voltage (VCC=5[V],RL=2[k]) (VCC=5[V]) 50 LOW LEVEL SINK CURRENT [A] 40 0 0 OUTPUT SOURCE CURRENT [mA] OUTPUT SOURCE CURRENT [mA] MAXIMUM OUTPUT VOLTAGE [V] MAXIMUM OUTPUT VOLTAGE [V] -40 10 15 20 25 SUPPLY VOLTAGE [V] 30 35 Fig. 82 Low Level Sink Current - Supply Voltage (VOUT=0.2[V]) 6 -40 25 4 2 0 -2 105 125 -4 -6 -8 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 83 Low Level Sink Current - Ambient Temperature (VOUT=0.2[V]) 0 5 10 15 20 25 SUPPLY VOLTAGE [V] 30 35 Fig. 84 Input Offset Voltage - Supply Voltage (Vicm=0[V], VOUT=1.4[V]) (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 10/17 2011.06 - Rev.B LM358DR/PWR/DGKR,LM2904DR/PWR/DGKR/VQDR/VQPWR LM324DR/PWR/KDR,LM2902DR/PER/KDR/KPWR/KVQDR/KVQPWR Technical Note Reference Data LM2902 family LM2902 family 8 LM2902 family 50 3V 2 0 5V -2 32V -4 40 30 20 10 105 -6 20 3V 10 5V 0 0 0 25 50 75 0 100 125 150 Fig. 85 Input Offset Voltage - Ambient Temperature (Vicm=0[V], VOUT=1.4[V]) 30 20 10 0 30 -50 35 -10 6 -40 4 105 25 125 2 0 -2 -4 -6 0 25 50 75 100 125 150 0 AMBIENT TEMPERATURE [] Fig. 88 Input Bias Current - Ambient Temperature (VCC=30[V],Vicm=28[V],VOUT=1.4[V]) 3V 0 5V 32V -5 1 2 3 [V] INPUT VOLTAGE [Vin] 4 -10 130 -40 25 120 110 100 90 105 0 25 50 75 125 80 70 100 125 150 AMBIENT TEMPERATURE [] Fig. 91 Input Offset Current - Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) 25 100 80 105 125 60 40 0 10 20 30 SUPPLY VOLTAGE [V] Fig. 94 Common Mode Rejection Ratio - Supply Voltage 40 15 20 25 30 35 Fig. 90 Input Offset Current - Supply Voltage (Vicm=0[V],VOUT=1.4[V]) LM2902 family 140 130 15V 120 110 100 5V 90 80 70 6 8 10 12 SUPPLY VOLTAGE [V] 14 -50 16 Fig. 92 Large Signal Voltage Gain - Supply Voltage (RL=2[k]) -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 93 Large Signal Voltage Gain - Ambient Temperature (RL=2[k]) LM2902 family COMMON MODE REJECTION RATIO [dB] -40 120 10 60 4 LM2902 family 140 5 SUPPLY VOLTAGE [V] 140 36V 120 100 80 5V 3V 60 40 -50 -25 LM2902 family 140 32V 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 95 Common Mode Rejection Ratio - Ambient Temperature POWER SUPPLY REJECTION RATIO [dB] -25 125 105 -5 0 60 -50 0 5 LM2902 family 140 LARGE SIGNAL VOLTAGE GAIN [dB] 5 25 -40 Fig. 89 Input Offset Voltage - Common Mode Input Voltage (VCC=5[V]) LM2902 family 10 5 -10 -1 LARGE SIGNAL VOLTAGE GAIN [dB] -25 LM2902 family 10 -8 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 87 Input Bias Current - Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) LM2902 family 8 INPUT OFFSET VOLTAGE [mV] 40 10 15 20 25 SUPPLY VOLTAGE [V] Fig. 86 Input Bias Current - Supply Voltage (Vicm=0[V], VOUT=1.4[V]) LM2902 family 50 5 INPUT OFFSET CURRENT [nA] -25 AMBIENT TEMPERATURE [] INPUT BIAS CURRENT[nA] 32V 30 125 -50 INPUT OFFSET CURRENT [nA] 25 -40 40 INPUT BIAS CURRENT [nA] 4 INPUT BIAS CURRENT [nA] INPUT OFFSET VOLTAGE [mV] 6 -8 COMMON MODE REJECTION RATIO [dB] LM2902 family 50 130 120 110 100 90 80 70 60 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 96 Power Supply Rejection Ratio - Ambient Temperature (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 11/17 2011.06 - Rev.B LM358DR/PWR/DGKR,LM2904DR/PWR/DGKR/VQDR/VQPWR LM324DR/PWR/KDR,LM2902DR/PER/KDR/KPWR/KVQDR/KVQPWR Technical Note Circuit Diagram Vcc INOUT IN+ GND Fig.97 Circuit Diagram (each Op-Amp) Measurement Circuit 1 NULL Method Measurement Condition Measurement item VF S1 S2 S3 Vcc,GND,EK,VICR Unit:[V] LM2904/LM2902 family Calculation Vcc GND EK VICR LM358/LM324 family Vcc GND EK VICR 0 1.4 0 VF1 ON ON OFF 5 to 30 Input Offset Current VF2 OFF OFF OFF 5 0 1.4 0 5 0 VF3 OFF ON 5 0 1.4 0 5 0 5 0 1.4 0 5 0 1.4 0 15 0 1.4 0 15 0 1.4 0 15 0 -11.4 0 15 0 -11.4 0 5 0 1.4 0 5 0 1.4 0 5 0 1.4 3.5 5 0 1.4 3.5 5 0 1.4 0 5 0 1.4 0 30 0 1.4 0 30 0 1.4 0 Input Bias Current VF4 ON OFF VF5 Large Signal Voltage Gain VF6 VF7 Common-mode Rejection Ratio VF8 VF9 Supply Voltage Rejection Ratio VF10 OFF ON ON ON ON ON OFF ON ON OFF 5 to 30 0 1.4 Input Offset Voltage 0 1 1.4 0 2 1.4 0 3 4 5 6 Calculation 1.Input Offset Voltage (VIO) Vio VF1 1+ Rf /Rs 0.1[F] [V] 2. Input offset current (IIO) Iio VF2 - VF1 Rf 50[k] [A] 500[k] Ri (1+ Rf / Rs) S1 3.Input Bias Current (IIB) +15[V] Rs VF4 - VF3 [A] Ib 2x Ri (1+ Rf / Rs) VICR DUT S3 Ri 1000[pF] S2 Rf 5.Common-mode rejection ratio (CMRR) 3.5x (1+ Rf/ Rs) VF8-VF7 500[k] 50[] 10[k] Rs 10x (1+ Rf /Rs) [dB] VF6 - VF5 CMRR 20x Log Ri 50[] 10[k] 4.Large Signal Voltage Gain (AVD) AV 20x Log Vcc 0.1[F] VOUT EK GND RL -15[V] V VF 50[k] [dB] Fig.98 Measurement Circuit 1 (each Op-Amp) 6.Supply Voltage rejection ratio (KSVR) Vccx(1+Rf/Rs) PSRR = 20xLog VF10 - VF9 [dB] Vcc=25V www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 12/17 2011.06 - Rev.B LM358DR/PWR/DGKR,LM2904DR/PWR/DGKR/VQDR/VQPWR LM324DR/PWR/KDR,LM2902DR/PER/KDR/KPWR/KVQDR/KVQPWR Technical Note Measurement Circuit 2: Switch Condition SW 1 SW No. SW 2 SW 3 SW 4 SW 5 SW 6 SW 7 SW 8 SW 9 SW 10 SW 11 SW 12 SW 13 SW 14 SW 15 Supply Current OFF OFF OFF ON OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF High Level Output Voltage OFF OFF ON OFF OFF OFF ON OFF OFF ON OFF OFF OFF ON OFF Low Level Output Voltage OFF OFF ON OFF OFF OFF ON OFF OFF OFF OFF OFF OFF ON OFF Output Source Current OFF OFF ON OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF ON Output Sink Current OFF OFF ON OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF ON Slew Rate OFF OFF OFF ON OFF OFF OFF OFF ON Unity-gain Bandwidth Product OFF ON OFF OFF OFF ON Equivalent Input Noise Voltage ON OFF OFF OFF ON OFF ON OFF OFF OFF OFF ON OFF OFF OFF ON ON OFF OFF OFF OFF ON OFF OFF ON ON OFF OFF OFF OFF Input voltage 3[V] SW4 SW5 R2 SW6 R3 Vcc 0.5[V] A t Input waveform Output voltage SW1 SW2 SR V / t SW3 3[V] SW10 SW11 SW12 SW13 SW14 SW15 RS R1 SW7 SW8 SW9 GND V A VIN- VIN+ RL CL V V t VOUT 0.5[V] t Output waveform Fig.99 Measurement Circuit 2 (each Op-Amp) Fig.100 Slew Rate Input Waveform Measurement Circuit 3: Cross-talk Attenuation R2=100[k] R2=100[k] Vcc=+2.5[V] Vcc=+2.5[V] R1=1[k] R1=1[k] other CH CH1 VIN V R1//R2 GND=-2.5[V] VOUT1 =0.5 [Vrms] V R1//R2 GND=-2.5[V] VO1/VO2=20xlog VOUT2 100xVOUT1 VOUT2 Fig.101 Measurement Circuit 3 www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 13/17 2011.06 - Rev.B LM358DR/PWR/DGKR,LM2904DR/PWR/DGKR/VQDR/VQPWR LM324DR/PWR/KDR,LM2902DR/PER/KDR/KPWR/KVQDR/KVQPWR Technical Note Description of Electrical Characteristics Described below are descriptions of the relevant electrical terms Please note that item names, symbols and their meaning may differ form those on another manufacturer's documents. 1. Absolute maximum ratings The absolute maximum ratings are values that should never be exceeded, since doing so may result in deterioration of characteristics or damage to the part itself as well as peripheral components. 1.1 Power supply voltage (Vcc/GND) Expresses the maximum voltage that can be supplied between the positive and negative power supply terminals without causing deterioration of characteristics or destruction of the internal circuitry. 1.2 Differential input voltage (VID) Indicates the maximum voltage that can be supplied between the non-inverting and inverting terminals without damaging the IC. 1.3 Input common-mode voltage range (VICR) Signifies the maximum voltage that can be supplied to the non-inverting and inverting terminals without causing deterioration of the electrical characteristics or damage to the IC itself. Normal operation is not guaranteed within the input common-mode voltage range of the maximum ratings - use within the input common-mode voltage range of the electric characteristics instead. 1.4 Operating temperature range and storage temperature range (Topr, Tstg) The operating temperature range indicates the temperature range within which the IC can operate. The higher the ambient temperature, the lower the power consumption of the IC. The storage temperature range denotes the range of temperatures the IC can be stored under without causing excessive deterioration of the electrical characteristics. 1.5 Power dissipation (Pd) Indicates the power that can be consumed by a specific mounted board at ambient temperature (25). For packaged products, Pd is determined by the maximum junction temperature and the thermal resistance. 2. Electric characteristics 2.1 Input offset voltage (VIO) Signifies the voltage difference between the non-inverting and inverting terminals. It can be thought of as the input voltage difference required for setting the output voltage to 0V. 2.2 Input offset voltage drift (VIO) Denotes the ratio of the input offset voltage fluctuation to the ambient temperature fluctuation. 2.3 Input offset current (IIO) Indicates the difference of the input bias current between the non-inverting and inverting terminals. 2.4 Input offset current drift (IIO) Signifies the ratio of the input offset current fluctuation to the ambient temperature fluctuation. 2.5 Input bias current (IIB) Denotes the current that flows into or out of the input terminal, it is defined by the average of the input bias current at the non-inverting terminal and the input bias current at the inverting terminal. 2.6 Circuit current (ICC) Indicates the current of the IC itself that flows under specific conditions and during no-load steady state. 2.7 High level output voltage/low level output voltage (VOH/VOL) Signifying the voltage range that can be output by under specific load conditions, it is in general divided into high level output voltage and low level output voltage. High level output voltage indicates the upper limit of the output voltage, while low level output voltage the lower limit. 2.8 Differential voltage amplification (AVD) The amplifying rate (gain) of the output voltage against the voltage difference between non-inverting and inverting terminals, it is (normally) the amplifying rate (gain) with respect to DC voltage. AVD = (output voltage fluctuation) / (input offset fluctuation) 2.9 Input common-mode voltage range (VICR) Indicates the input voltage range under which the IC operates normally. 2.10 Common-mode rejection ratio (CMRR) Signifies the ratio of fluctuation of the input offset voltage when the in-phase input voltage is changed (DC fluctuation). CMRR = (change in input common-mode voltage) / (input offset fluctuation) 2.11 Power supply rejection ratio (KSVR) Denotes the ratio of fluctuation of the input offset voltage when the supply voltage is changed (DC fluctuation). KSVR = (change in power supply voltage) / (input offset fluctuation) 2.12 Output source current/ output sink current (IOH/IOL) The maximum current that can be output under specific output conditions, it is divided into output source current and output sink current. The output source current indicates the current flowing out of IC, and the output sink current the current flowing into the IC. 2.13 Cross talk attenuation (VO1/VO2) Expresses the amount of fluctuation in the input offset voltage or output voltage with respect to the change in the output voltage of a driven channel. 2.14 Slew rate at unity gain (SR) Indicates the time fluctuation ratio of the output voltage when an input step signal is supplied. 2.15 Unity gain bandwidth (B1) The product of the specified signal frequency and the gain of the op-amp at such frequency, it gives the approximate value of the frequency where the gain of the op-amp is 1 (maximum frequency, unity gain frequency). www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 14/17 2011.06 - Rev.B LM358DR/PWR/DGKR,LM2904DR/PWR/DGKR/VQDR/VQPWR LM324DR/PWR/KDR,LM2902DR/PER/KDR/KPWR/KVQDR/KVQPWR Technical Note Derating Curves 1000 LM358DGKR LM358DR LM2904PWR LM2904VQPWR POWER DISSIPATION Pd [mW] POWER DISSIPATION Pd [mW] 800 600 LM358PWR LM2904DGKR LM2904DR LM2904VQDR 400 200 0 800 25 50 75 LM2902DR LM2902KDR LM2902KQVDR 600 LM324PWR 400 LM324DR LM324KDR 200 0 70 0 LM2902PWR LM2902KPWR LM2902KQVPWR 100 125 150 70 0 AMBIENT TEMPERATURE [] LM358DR/PWR/DGKR LM2904DR/PWR/DGKR/VQDR/VQPWR 50 75 100 125 150 LM324DR/PWR/KDR LM2902DR/PWR/KDR/KPWR/KQDR/KQPWR Power Dissipation Package 25 AMBIENT TEMPERATURE [] Power Dissipation Pd[W] ja [/W] Package Pd[W] ja [/W] SOIC8 (*8) 450 3.6 SOIC14 610 4.9 TSSOP8 (*6) 500 4.0 TSSOP14 870 7.0 MSOP8/VSSOP8 (*7) 470 3.76 ja = (Tj-Ta)/Pd[/W] Fig.102 Derating Curves Precautions 1) Unused circuits When there are unused circuits, it is recommended that they be connected as in Figure 103, setting the non-inverting input terminal to a potential within the in-phase input voltage range (VICR). 2) Input terminal voltage Applying GND + 32V to the input terminal is possible without causing deterioration of the electrical characteristics or destruction, irrespective of the supply voltage. However, this does not ensure normal circuit operation. Please note that the circuit operates normally only when the input voltage is within the common mode input voltage range of the electric characteristics. V cc connect to V icm GND 3) Power supply (single / dual) The op-amp operates when the voltage is applied between Vcc and GND. Therefore, the single supply op-amp can be used as a dual supply op-amp as well. Fig.103 Disable circuit example 4) Power dissipation (Pd) Using the unit in excess of the rated power dissipation may cause deterioration in electrical characteristics due to the rise of chip temperature, including reduced current capability. Therefore, please take into consideration the power dissipation (Pd) under the actual operating conditions and apply a sufficient margin in thermal design. Refer to the thermal derating curves for more information. 5) Short-circuits between pins and erroneous mounting Incorrect mounting may damage the IC. In addition, the presence of foreign substances between the outputs, the output and the power supply, or the output and GND may also result in IC destruction. 6) Operation in a strong electromagnetic field Operation in a strong electromagnetic field may cause malfunctions. 7) Radiation This IC is not designed to withstand radiation. 8) IC handing Applying mechanical stress to the IC by deflecting or bending the board may cause fluctuation of the electrical characteristics due to piezoelectric (piezo) effects. 9) IC operation The output stage of the IC is configured using Class C push-pull circuits. Therefore, when the load resistor is connected to the middle potential of Vcc and GND, crossover distortion occurs at the changeover between discharging and charging of the output current. Connecting a resistor between the output terminal and GND and increasing the bias current for Class A operation will suppress crossover distortion. 10) Board inspection Connecting a capacitor to a pin with low impedance may stress the IC. Therefore, discharging the capacitor after every process is recommended. In addition, when attaching and detaching the jig during the inspection phase, ensure that the power is turned OFF before inspection and removal. Furthermore, please take measures against ESD in the assembly process as well as during transportation and storage. 11) Output capacitor Discharge of the external output capacitor to Vcc is possible via internal parasitic elements when Vcc is shorted to GND, causing damage to the internal circuitry due to thermal stress. Therefore, when using this IC in circuits where oscillation due to output capacitive load does not occur, such as in voltage comparators, use an output capacitor with a capacitance less than 0.1F. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 15/17 2011.06 - Rev.B LM358DR/PWR/DGKR,LM2904DR/PWR/DGKR/VQDR/VQPWR LM324DR/PWR/KDR,LM2902DR/PER/KDR/KPWR/KVQDR/KVQPWR Technical Note Ordering part number L M 2 9 0 2 Family name LM358 LM324 LM2902 LM2904 K V ESD tolerance application K : 2kV None : Normal Q D R Operating Voltage Package type VQ : 32V None : 26V D : SOIC P W : TSSOP DGK : MSOP/VSSOP R : Real SOIC8 <Tape and Reel information> 4.90.2 (MAX 5.25 include BURR) 6 5 0.45Min. 7 3.90.2 6.00.3 8 4 +6 -4 1 2 3 Tape Embossed carrier tape Quantity 2500pcs Direction of feed ( reel on the left hand and you pull out the tape on the right hand The direction is the 1pin of product is at the upper left when you hold ) 4 0.545 0.20.1 0.175 1.3750.1 S 1.27 0.420.1 1pin 0.1 S Reel (Unit : mm) Direction of feed Order quantity needs to be multiple of the minimum quantity. SOIC14 <Tape and Reel information> 8.650.1 (Max 9.0 include BURR) 0.65 0.15 1 1PIN MARK Tape Embossed carrier tape Quantity 2500pcs Direction of feed ( reel on the left hand and you pull out the tape on the right hand The direction is the 1pin of product is at the upper left when you hold ) 7 0.175 0.075 S +0.05 0.22 -0.03 1.375 0.075 1.65MAX 0.515 1.050.2 8 6.0 0.2 3.9 0.1 14 4 +6 -4 +0.05 0.42 -0.04 1.27 0.08 S 0.08 M 1pin Reel (Unit : mm) Direction of feed Order quantity needs to be multiple of the minimum quantity. TSSOP8 <Tape and Reel information> 3.00.1 (MAX 3.35 include BURR) 7 6 0.5 0.15 3 2500pcs Direction of feed ( reel on the left hand and you pull out the tape on the right hand 4 1PIN MARK The direction is the 1pin of product is at the upper left when you hold ) 1.00.2 2 Embossed carrier tape Quantity +0.05 0.145 -0.03 1.0 0.05 S 0.1 0.05 1.2MAX 1 0.525 Tape 5 6.4 0.2 4.4 0.1 8 44 0.08 S +0.05 0.245 -0.04 0.08 M 1pin 0.65 (Unit : mm) www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. Reel 16/17 Direction of feed Order quantity needs to be multiple of the minimum quantity. 2011.06 - Rev.B LM358DR/PWR/DGKR,LM2904DR/PWR/DGKR/VQDR/VQPWR LM324DR/PWR/KDR,LM2902DR/PER/KDR/KPWR/KVQDR/KVQPWR Technical Note TSSOP14 <Tape and Reel information> 5.00.1 (Max 5.35 include BURR) 4 4 14 1 Tape Embossed carrier tape Quantity 2500pcs Direction of feed ( reel on the left hand and you pull out the tape on the right hand The direction is the 1pin of product is at the upper left when you hold ) 7 1PIN MARK +0.05 0.145 -0.03 0.10.05 S 1.00.05 1.2MAX 0.55 1.00.2 0.50.15 6.40.2 4.40.1 8 0.08 S +0.05 0.245 -0.04 0.65 0.08 1pin M Reel (Unit : mm) Direction of feed Order quantity needs to be multiple of the minimum quantity. MSOP / VSSOP8 <Tape and Reel information> 3.00.1 (MAX 3.35 include BURR) 6 5 0.45 0.15 2 3 4 1PIN MARK Tape Embossed carrier tape Quantity 2500pcs Direction of feed ( reel on the left hand and you pull out the tape on the right hand The direction is the 1pin of product is at the upper left when you hold ) 0.95 0.2 1 +0.05 0.145 -0.03 0.525 0.10.05 S 0.850.05 1.1MAX 7 3.0 0.1 4.9 0.2 8 44 0.08 S +0.05 0.32 -0.04 0.08 M 1pin 0.65 (Unit : mm) www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. Reel 17/17 Direction of feed Order quantity needs to be multiple of the minimum quantity. 2011.06 - Rev.B Datasheet Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you (Note 1) , transport intend to use our Products in devices requiring extremely high reliability (such as medical equipment equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property ("Specific Applications"), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM's Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASS CLASSb CLASS CLASS CLASS CLASS 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM's Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice - GE (c) 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM's internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: 2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice - GE (c) 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM's Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM's Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an "as is" basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice - WE (c) 2014 ROHM Co., Ltd. All rights reserved. Rev.001 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: ROHM Semiconductor: LM2902PWR LM2904DGKR LM2904PWR LM2904VQPWR LM358DGKR