2009 Microchip Technology Inc. DS21711J-page 1
24AA01/24LC01B
Device Selection Table
Features:
• Single Supply with Operation down to 1.7V for
24AAXX Devices, 2.5V for 24LCXX Devices
• Low-Power CMOS Technology:
- Read current 1 mA, max.
- Standby current 1 A, max. (I-temp)
• 2-Wire Serial Inte rfac e, I2C™ Compatible
• Schmitt Trigger inputs for Noise Suppression
• Output Slope Control to eliminate Ground Bounce
• 100 kHz and 400 kHz Compatibility
• Page Write Time 3 ms, typical
• Hardware Write-Protect
• ESD Protection >4,000V
• More than 1 Million Erase/Write Cycles
• Data Retention >200 Years
• Factory Programmable Available
• Packages include 8-lead PDIP, SOIC, TSSOP,
DFN, TDFN, MSOP, 5-lead SOT-23 and SC-70
• Pb-free and RoHS Compliant
• Temperature Ranges:
- Industrial (I): -40°C to +85°C
- Automotive (E): -40°C to +125°C
Description:
The Microchip Technology Inc. 24AA01/24LC01B
(24XX01* ) is a 1 Kb it El ect ric all y Era sable PROM. Th e
devi ce is orga nized as o ne block o f 128 x 8 -bit mem ory
with a 2-wire serial interface. Low-voltage design
permit s operation down to 1.7V with st andby and ac tive
currents of only 1 A and 1 mA, respectively. The
24XX01 also has a page write capability for up to 8
bytes of data. The 24XX01 is available in the standard
8-pin PDIP, surface mount SOIC, TSSOP, 2x3 DFN,
2x3 TDFN and MSOP packages, and is also available
in the 5-lead SOT-23 and SC-70 packages.
Package Types
Block Diagram
Part
Number VCC
Range Max. Clock
Frequency Temp.
Ranges
24AA01 1.7-5.5 400 kHz(1) I
24LC01B 2.5-5.5 400 kHz I, E
Note 1: 100 kHz for VCC <2.5V.
A0
A1
A2
VSS
VCC
WP
SCL
SDA
1
2
3
4
8
7
6
5
PDIP, MSOP SOIC, TSSOP
A0
A1
A2
VSS
1
2
3
4
8
7
6
5
VCC
WP
SCL
SDA
DFN/TDFN
A0
A1
A2
VSS
WP
SCL
SDA
VCC
SOT-23/SC-70
15
4
3
SCL
Vss
SDA
WP
Vcc
2
Note: Pins A0, A1 and A2 are not used by the 24XX01 (no
intern al connect ions).
8
7
6
5
1
2
3
4
HV Ge n erato r
EEPROM
Array
Page Latches
YDEC
XDEC
Sense Amp.
Memory
Control
Logic
I/O
Control
Logic
I/O
WP
SDA
SCL
VCC
VSS R/W Control
1K I2C™ Serial EEPROM
24AA01/24LC01B
DS21711J-page 2 2009 Microchip Technology Inc.
1.0 ELECTRICAL CHARAC TERISTICS
Absolute Maximum Ratings (†)
VCC.............................................................................................................................................................................6.5V
All inputs and outputs w.r.t. VSS ......................................................................................................... -0.3V to VCC +1.0V
Storage temperature ...............................................................................................................................-65°C to +150°C
Ambient temperature with power applied................................................................................................-40°C to +125°C
ESD protection on all pins 4kV
TABLE 1-1: DC CHARACTERISTICS
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to
the device. This is a stress rating only and functional operation of the device at those or any other conditions
above th ose indi cated in the opera tional li stings of this sp ecificati on is no t implie d. Exposu re to max imum rating
conditions for extended periods may affect device reliability.
DC CHARACTERISTICS Industrial (I): TA = -40°C to +85°C, VCC = +1.7V to +5.5V
Automotive (E): TA = -40°C to +125°C, VCC = +2.5V to +5.5V
Param.
No. Sym. Characteristic Min. Typ. Max. Units Conditions
D1 VIH WP, SCL and SDA pins —————
D2 — High-level input voltage 0.7 VCC ——V—
D3 VIL Low-level input voltage — — 0.3 VCC V—
D4 VHYS Hysteresis of Schmitt
Trigger inputs 0.05 VCC ——V(Note)
D5 VOL Low-level output voltage — — 0.40 V IOL = 3.0 mA, VCC = 2.5V
D6 ILI Input leakage current ——±1AVIN = VSS or VCC
D7 ILO Output le akage curren t ——±1AVOUT = VSS or VCC
D8 CIN,
COUT Pin capacitance
(all inputs/ou tpu t s) ——10pFVCC = 5. 0V (Note)
TA = 25°C, FCLK = 1 MHz
D9 ICC write Operating current —0.13mAVCC = 5.5V, SCL = 400 kHz
D10 ICC read — 0.05 1 mA —
D11 ICCS Standby current —
—0.01
—1
5
Industrial
Automotive
SDA = SCL = VCC
WP = VSS
Note: This parameter is periodically sampled and not 100% tested.
2009 Microchip Technology Inc. DS21711J-page 3
24AA01/24LC01B
TABLE 1-2: AC CHARACTERISTICS
AC CHARACTERISTICS Industrial (I): TA = -40°C to +85°C, VCC = +1.7V to +5.5V
Automotive (E): TA = -40°C to +125°C, VCC = +2.5V to +5.5V
Param.
No. Sym. Characteristic Min. Typ. Max. Units Conditions
1F
CLK Clock frequency —
——
—400
100 kHz 2.5V VCC 5.5V
1.7V VCC 2.5V (24AA01)
2T
HIGH Clock high time 600
4000 —
——
—ns 2.5V VCC 5.5V
1.7V VCC 2.5V (24AA01)
3TLOW Clock low time 1300
4700 —
——
—ns 2.5V VCC 5.5V
1.7V VCC 2.5V (24AA01)
4TRSDA and SCL rise time
(Note 1) —
——
—300
1000 ns 2.5V VCC 5.5V
1.7V VCC 2.5V (24AA01)
5T
FSDA and SCL fall time — —
—300 ns (Note 1)
6T
HD:STA Start condition hold time 600
4000 —
——
—ns 2.5V VCC 5.5V
1.7V VCC 2.5V (24AA01)
7TSU:STA Start condition setup
time 600
4700 —
——
—ns 2.5V VCC 5.5V
1.7V VCC 2.5V (24AA01)
8T
HD:DAT Data input hold time 0 —
——ns(Note 2)
9T
SU:DAT Data input setup time 100
250 —
——
—ns 2.5V VCC 5.5V
1.7V VCC 2.5V (24AA01)
10 TSU:STO Stop condition setup
time 600
4000 —
——
—ns 2.5V VCC 5.5V
1.7V VCC 2.5V (24AA01)
11 TAA Output valid from clock
(Note 2) —
——
—900
3500 ns 2.5V VCC 5.5V
1.7V VCC 2.5V (24AA01)
12 TBUF Bus free-time: Time the
bus mu st be free befo r e
a new transmission can
start
1300
4700 —
——
—ns 2.5V VCC 5.5V
1.7V VCC 2.5V (24AA01)
13 TOF Output fall time from VIH
minimum to VIL
maximum
20+0.1CB
——
—250
250 ns 2.5V VCC 5.5V
1.7V VCC 2.5V (24AA01)
14 TSP Input filter spike
suppression
(SDA and SCL pins)
— — 50 ns (N otes 1 and 3)
15 TWC Write cycl e time
(byte or page) ——5ms—
16 — Endurance 1M — — cycles 25°C, (Note 4)
Note 1: Not 100% tested. CB = total capacitance of one bus line in pF.
2: As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region
(minimum 300 ns) of the falling edge of SCL to avoid unintended generation of Start or Stop conditions.
3: The co mbine d TSP and VHYS s pec ifi ca tio ns are due to n ew Sc hm it t Trigger inp ut s w h ic h p rov id e i mp rov ed
noise spike suppression. This eliminates the need for a TI specification for standard operation.
4: This parameter is not tested but ensured by characterization. For endurance es timates in a specific
applic ation, pl ease co nsult the Total Enduran ce™ Mode l which ca n be obt ain ed from Mi crochi p’ s web site
at www.microchip.com.
24AA01/24LC01B
DS21711J-page 4 2009 Microchip Technology Inc.
FIGURE 1-1: BUS TIMING DATA
FIGURE 1-2: BUS T IMING START/STOP
7
524
8910
12
11
14 6
SCL
SDA
IN
SDA
OUT
3
76
D4
10
Start Stop
SCL
SDA
2009 Microchip Technology Inc. DS21711J-page 5
24AA01/24LC01B
2.0 PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 2-1.
TABLE 2-1: PIN FUNCTION TABLE
2.1 A0, A1, A2
The A0, A1 and A2 pins are not used by the 24XX01.
They may be left floating or tied to either VSS or VCC.
2.2 Serial Address/Data Input/Output
(SDA)
The SDA input is a bidirectional pin used to transfer
addresse s and data into an d out of the device . Since
it is an open-drain terminal, the SDA bus requires a
pull-up resistor to VCC (typical 10 k for 100 kHz,
2k for 40 0 k Hz ).
For normal data transfer, SDA is allowed to change
only during SCL low. Changes during SCL high are
reserved for indicating Start and Stop conditions.
2.3 Serial Clock (SCL)
The SCL in put is u sed to sy nc hro niz e th e da t a tra nsfer
to and from the device.
2.4 Wr it e-Protect (WP)
This pin must be connected to either VSS or VCC.
If tied to VSS, normal memory operation is enabled
(read/wri te the ent ire memory 00-7F).
If tied to VCC, write operations are inhibited. The entire
memory will be write-protected. Read operations are
not affected.
Name PDIP SOIC TSSOP DFN TDFN MSOP SOT23 SC-70 Description
A0 1 1 1 1 1 1 — — Not Connected
A1 2 2 2 2 2 2 — — Not Connected
A2 3 3 3 3 3 3 — — Not Connected
VSS 4 4 4 4 4 4 2 2 Ground
SDA 5 5 5 5 5 5 3 3 Serial Address/Data I/O
SCL 6 6 6 6 6 6 1 1 Serial Clock
WP 7 7 7 7 7 7 5 5 Write-Protect Input
VCC 8 8 8 8 8 8 4 4 +1.7V to 5.5V Power Supply
24AA01/24LC01B
DS21711J-page 6 2009 Microchip Technology Inc.
3.0 FUNCTIONAL DESCRIPTION
The 24XX01 supports a bidirectional, 2-wire bus and
data transmission protocol. A device that sends data
onto the bus is defined as transmitter, while defining a
device receiving data as a receiver. The bus has to be
controlled by a master device which generates the
Serial Clock (SCL), controls the bus access and
generates the Start and Stop conditions, while the
24XX01 works as slave. Both master and slave can
operate as transmitter or receiver, but the master
device determines which mode is activated.
4.0 BUS CHARACTERISTICS
The following bus protocol has been defined:
• Data transfer may be initiated only when the bus
is not busy.
• During data transfer, the data line must remain
stab le when ever th e clock lin e is high . Change s in
the data line while the clock line is high will be
interpreted as a Start or Stop condition.
Accordingly, the following bus conditions have been
defined (Figu re 4-1).
4.1 Bus Not Busy (A)
Both data and clock lines remain high.
4.2 Start Data Transfer (B)
A high-to-low transition of the SDA line while the clock
(SCL) is high determines a Start condition. All
commands must be preceded by a Start condition.
4.3 S top Data Transfer (C)
A low-to-high transition of the SDA line while the clock
(SCL) is high determines a Stop condition. All
operations must be ended with a Stop condition.
4.4 Data Valid (D)
The state of the data line represents valid data when,
after a Start condition, the data line is stable for the
duration of the high period of the clock signal.
The data on the line must be changed during the low
period of the clock signal. There is one clock pulse per
bit of data.
Each dat a transf er is initiated w ith a S tart condition an d
terminated with a Stop condition. The number of data
bytes transferred between the Start and Stop
conditions is determined by the master device and is,
theoretically, unlimited (although only the last sixteen
will be st ored wh en do ing a w ri te op era tio n). W hen an
overwrite does occur, it will replace data in a first-in
first- out (FIFO) fashion.
4.5 Acknowledge
Each receiving device, when addressed, is obliged to
generate an acknowledge after the reception of each
byte. Th e mast er device mus t ge nera te a n ex tra c lock
pulse which is associated with this Acknowledge bit.
The device that acknowledges has to pull down the
SDA line d uring th e ackn owledge clock pulse in such a
way that the SDA line is stable-low during the high
period of the acknowledge-related clock pulse. Of
course, setup and hold times must be taken into
account. During reads, a master must signal an end of
data to t he sla ve by not ge nerati ng an Ac knowl edge b it
on the las t by te that has be en c loc ke d ou t of th e sl av e.
In this c as e, the sl ave (24XX01) w ill le av e th e d at a line
high to enable the master to generate the Stop
condition.
FIGURE 4-1: DAT A TRANSFER SEQUENCE ON THE SERIAL BUS
Note: The 24XX01 does not generate any
Acknowledge bits if an internal
programming cycle is in progress.
SCL
SDA
(A) (B) (D) (D) (A)(C)
Start
Condition Address or
Acknowledge
Valid
Data
Allowed
to Change
Stop
Condition
2009 Microchip Technology Inc. DS21711J-page 7
24AA01/24LC01B
5.0 DEVICE ADDRESSING
A control byte is the first byte received following the
S tar t condition from the m aster device . The co ntrol byte
consis ts of a four -bit control c ode. For the 24XX01, thi s
is set as ‘1010’ binary for read and write operations.
The next three bits of the control byte are “don’t cares”
for the 24XX01.
The last bit of the control byte defines the operation to
be performed. When set to ‘1’, a read operation is
select ed. W hen set to ‘0’ , a write operati on is se lecte d.
Follow in g the Start condi tio n, the 24XX01 moni tors the
SDA bus, checking the device type identifier being
transmitted. Upon receiving a ‘1010’ code, the slave
device output s an Acknow ledge signal on the SDA lin e.
Depen din g on th e state of the R/W bit, the 24XX01 wil l
select a read or write operation.
FIGU RE 5-1 : CONTROL BYT E
ALLOCATION
FIGURE 5-2: ADDRESS SEQUENCE BIT ASSIGN MENTS
Operation Control
Code Block Select R/W
Read 1010 Block Addre ss 1
Write 1010 Block Address 0
1010xxx
R/W ACK
Start Bit
Read/Write Bit
x = “don’t care”
S
Slave Address
Acknowledge Bit
Control Code
Block
Select
Bits
1010xxR/W A
6A
0
•••••
Control Byte Address Low Byte
Control
Code Block
Select
bits
x = “don’t care”
xx
24AA01/24LC01B
DS21711J-page 8 2009 Microchip Technology Inc.
6.0 WRITE OPERATION
6.1 Byte Write
Following the Start condition from the master, the
device code (4 bits), the block address (3 bits, “don’t
cares”) and the R/W bit, which is a logic-low, is placed
onto the bus by the master transmitter . This indicates to
the addressed slave receiver that a byte with a word
address will follow after it has generated an Acknowl-
edge bit during the ninth clock cycle. Therefore, the
next byte transmitted by the master is the word address
and will be written into the Address Pointer of the
24XX01. After receiving another Acknowledge signal
from the 24XX01, the master device will transmit the
data word to be written into the addressed memory
location. The 24XX01 acknowledges again and the
master generates a Stop condition. This initiates the
internal write cycle, and, during this time, the 24XX01
will not generate Acknowledge signals (Figure 6-1).
6.2 Page Write
The write control byte, word add ress and firs t data by te
are transmitted to the 24XX01 in the same way as in a
byte write. However, instead of generating a Stop
conditi on, the mas ter transmit s up to 8 d ata bytes to the
24XX01, which are temporarily stored in the on-chip
page buffer and will be written into the memory once
the master has transmitted a Stop condition. Upon
receipt of each word, the four lower-order Address
Pointer bits are internally incremented by ‘1’. The
higher-order 7 bits of the word address remain
constant. If the master should transmit more than 8
words prior to generating the Stop condition, the
address counter will roll over and the previously
receive d dat a will be overwri tten. As w ith the by te write
operation, once the Stop condition is received, an
internal write cycle will begin (Figure 6-2).
6.3 Write Protection
The W P pin a llows th e user t o writ e-prote ct the entire
array (00-7F ) when the pin is tied to VCC. If tied to VSS,
the write protection is disabled.
FIGURE 6-1: BYTE WRITE
Note: Page write opera tions are l imited to wri ting
bytes within a single physical page
regardless of the number of bytes
actually being written. Physical page
boundaries start at addresses that are
integer multiples of the page buffer size (or
‘page siz e’ ) an d end at ad dres s es that are
integer multiples of [page size – 1]. If a
page write command attempts to write
across a physical page boundary, the
result is that the data wraps around to the
beginning of the current page (overwriting
data previously stored there), instead of
being w ritten to the next page, as migh t be
expected. It is therefore necessary for the
application software to prevent page write
operations that would attempt to cross a
page boundary.
S P
Bus Acti vity
Master
SDA Line
Bus Activity
S
T
A
R
T
S
T
O
P
Control
Byte Word
Address Data
A
C
K
A
C
K
A
C
K
1010xxx0
x = “don’t care”
Block
Select
Bits
2009 Microchip Technology Inc. DS21711J-page 9
24AA01/24LC01B
FIGURE 6-2: PAGE WRITE
S P
Bus Acti vity
Master
SDA Line
Bus Acti vity
S
T
A
R
T
Control
Byte Word
Address (n) Data (n) Data (n + 7)
S
T
O
P
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
Data (n + 1)
x = “don’t care”
10 10xxx0
Block
Select
Bits
24AA01/24LC01B
DS21711J-page 10 2009 Microchip Technology Inc.
7.0 ACKNOWLEDGE POLLING
Since the device will not acknowledge during a write
cycle, this can be used to determine when the cycle is
complete (this feature can be used to maximize bus
throughput). Once the Stop condition for a write
comma nd has been is sued from the master , the device
initiates the internally-timed write cycle. ACK polling
can then be initiated immediately. This involves the
master sending a S tart c ondition fo llowed by t he contro l
byte for a write c ommand (R/W = 0). If the devic e is still
busy wi th the write cycle, no ACK will be returned. If the
cycle is complete, the device will return the ACK and
the mas ter can then pr oceed with the nex t read or wr ite
command. See Figure 7-1 for a flow diagram of this
operation.
FIGURE 7-1: ACKNOWLEDGE POLLING
FLOW
Send
Write Command
Send Stop
Condition to
Initiate Write Cycle
Send Start
Send Control Byte
with R/W = 0
Did Device
Acknowledge
(ACK = 0)?
Next
Operation
No
Yes
2009 Microchip Technology Inc. DS21711J-page 11
24AA01/24LC01B
8.0 READ OPERATION
Read operations are initiated in the same way as write
operations, with the exception that the R/W bit of the
slave address is set to ‘1’. There are three basic types
of read operat ions: current address read , rand om rea d
and sequential read.
8.1 Current Address Read
The 24XX01 contains an address counter that
maintains the address of the last word accessed,
inter nal ly i nc rem ente d by ‘ 1’. Th erefore, if the p reviou s
access (either a read or write operation) was to
address n, the next current address read operation
would access data f rom add ress n + 1 . Upon re ceipt of
the slave address with R/W bit set to ‘1’, the 24XX01
issues an acknowledge and transmits the 8-bit data
word. Th e master will not acknowle dge the transfe r , but
does generate a Stop condition and the 24XX01
discontinues transmission (Figure 8-1).
8.2 Random Read
Random read operations allow the master to access
any memory location in a random manner. To perform
this typ e of re ad ope ratio n, the word add res s mus t firs t
be set. This is accomplished by sending the word
address to the 24XX01 as part of a write operation.
Once th e word address is s ent, the master ge nerates a
Start condition following the acknowledge. This
terminates the write operation, but not before the inter-
nal Address Pointer is set. The master then issues the
control byt e agai n, but wi th the R /W bit se t to a ‘ 1’. The
24XX01 will then issue an acknowledge and transmits
the 8-bit data word. The master will not acknowledge
the transfer , but do es generate a S top condition and the
24XX01 discontinues transmission (Figure 8-2).
8.3 Sequentia l Read
Sequential reads are initiated in the same way as a
random read, except that once the 24XX01 transmits
the first data byte, the master issues an acknowledge
(as opposed to a S top condition in a random read). This
directs the 24XX01 to transmit the next sequentially
addressed 8-bit word (Figure 8-3).
To provide sequential reads the 24XX01 contains an
internal Address Pointer which is incremented by one
at the completion of each operation. This Address
Pointer allows the entire memory contents to be serially
read during one operation.
8.4 Noise Protection
The 24XX01 employs a VCC threshold detector circuit
which disables the internal erase/write logic if the VCC
is below 1.5V at nominal conditions.
The SCL and SDA inputs have Schmitt Trigger and
filter circuits which suppress noise spikes to assure
proper device operation even on a noisy bus.
FIGURE 8-1: CURRENT ADDRESS READ
SP
Bus Activity
Master
SDA Line
Bus Activity
S
T
O
P
Control
Byte Data (n)
A
C
KN
o
A
C
K
S
T
A
R
T
Block
Select
Bits
x = “don’t care”
1010xxx1
24AA01/24LC01B
DS21711J-page 12 2009 Microchip Technology Inc.
FIGURE 8-2: RANDOM READ
FIGU RE 8-3 : SEQUE NT I AL RE A D
S P
S
Bus Activity
Master
SDA Line
Bus Activity
S
T
A
R
T
S
T
O
P
Control
Byte
A
C
K
Word
Address (n) Control
Byte
S
T
A
R
TData (n)
A
C
KA
C
KN
o
A
C
K
x = “don’t care”
1010 xxx01010xxx 1
Block
Select
Bits
Block
Select
Bits
P
Bus Activity
Master
SDA Line
Bus Activity
S
T
O
P
Control
Byte
A
C
KN
o
A
C
K
Data (n) Data (n + 1) Data (n + 2) Data (n + x)
A
C
KA
C
KA
C
K
1
2009 Microchip Technology Inc. DS21711J-page 13
24AA01/24LC01B
9.0 PACKAGING INFORMATION
9.1 Package Marking Information
XXXXXXXX
T/XXXNNN
YYWW
8-Lead PDIP (300 mil) Example:
8-Lead SOIC (3.90 mm) Example:
XXXXXXXT
XXXXYYWW
NNN
8-Lead TSSOP Example:
24LC01B
I/P 13F
0527
24LC01BI
SN 0527
13F
8-Lead MSOP Example:
XXXX
TYWW
NNN
XXXXT
YWWNNN
4L1B
I527
13F
4L1BI
52713F
5-Lead SOT-23 Example:
XXNN M13F
3
e
3
e
24AA01/24LC01B
DS21711J-page 14 2009 Microchip Technology Inc.
Part Numbe r
1st Line Marking Codes
TSSOP MSOP SOT-23 DFN TDFN SC-70
I Temp. E Temp. I Temp. E Temp. I Temp. E Temp. I Temp. E Temp.
24AA01 4A01 4A01T B1NN — 211 — A11 — B2NN —
24LC01B 4L1B 4L1BT M1NN N1NN 214 215 A14 A15 B1NN B3NN
Note: T = Temperature grade (I, E)
NN = Alphanumeric traceability code
Legend: XX...X Part number or part number code
T Temperature (I, E)
Y Year code (last digit of calendar year)
YY Year code (last 2 digits of calendar year)
WW Week c ode (w eek of January 1 is week ‘01’)
NNN Alphanumeric traceability code (2 characters for small packages)
Pb-free JEDEC designator for Matte Tin (Sn)
Note: For very small packages with no room for the Pb-free JEDEC designator
, the marking will only appear on the outer carton or reel label.
Note: In the event the full Mi croch ip pa rt numbe r can not be ma rked on one line , it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
3
e
3
e
8-Lead 2x3 TDFN
XXX
YWW
NN
A14
527
13
Example:
8-Lead 2x3 DFN
XXX
YWW
NN
214
527
13
Example:
5-Lead SC-70 Example:
XXNN B13F
Note: Please visit www.microchip.com/Pbfree for the latest information on Pb-free conversion.
*Standard OTP marking consists of Microchip part number, year code, week code, and traceability code.
2009 Microchip Technology Inc. DS21711J-page 15
24AA01/24LC01B
!"#$%&"' ()"&'"!&)&#*&&&#
+%&,&!&
- '!!#.#&"#'#%!&"!!#%!&"!!!&$#/!#
'!#&.0
1,21!'!&$& "!**&"&&!
3&'!&"&4#*!(!!&4%&&#&
&&255***''54
6&! 7,8.
'!9'&! 7 7: ;
7"')%! 7 <
& 1,
&& = =
##44!! -
1!&& = =
"#&"#>#& . - -
##4>#& . <
: 9& -< -?
&& 9 -
9#4!! <
69#>#& ) ?
9*9#>#& ) <
: *+ 1 = = -
N
E1
NOTE 1
D
12
3
A
A1
A2
L
b1
b
e
E
eB
c
* ,<1
24AA01/24LC01B
DS21711J-page 16 2009 Microchip Technology Inc.
! ""#$%& !'
!"#$%&"' ()"&'"!&)&#*&&&#
+%&,&!&
- '!!#.#&"#'#%!&"!!#%!&"!!!&$#''!#
'!#&.0
1,2 1!'!&$& "!**&"&&!
.32 %'!("!"*&"&&(%%'&"!!
3&'!&"&4#*!(!!&4%&&#&
&&255***''54
6&! 99..
'!9'&! 7 7: ;
7"')%! 7 <
& 1,
: 8& = =
##44!! = =
&#%%+ =
: >#& . ?1,
##4>#& . -1,
: 9& 1,
,'%@&A =
3&9& 9 =
3&& 9 .3
3& IB = <B
9#4!! =
9#>#& ) - =
#%& DB = B
#%&1&&' EB = B
D
N
e
E
E1
NOTE 1
12 3
b
A
A1
A2
L
L1
c
h
h
φ
β
α
* ,1
2009 Microchip Technology Inc. DS21711J-page 17
24AA01/24LC01B
! ""#$%& !'
3&'!&"&4#*!(!!&4%&&#&
&&255***''54
24AA01/24LC01B
DS21711J-page 18 2009 Microchip Technology Inc.
() )"* ! (+%+( !
!"#$%&"' ()"&'"!&)&#*&&&#
'!!#.#&"#'#%!&"!!#%!&"!!!&$#''!#
- '!#&.0
1,2 1!'!&$& "!**&"&&!
.32 %'!("!"*&"&&(%%'&"!!
3&'!&"&4#*!(!!&4%&&#&
&&255***''54
6&! 99..
'!9'&! 7 7: ;
7"')%! 7 <
& ?1,
: 8& = =
##44!! <
&#%% =
: >#& . ?1,
##4>#& . -
##49& - -
3&9& 9 ?
3&& 9 .3
3& IB = <B
9#4!! =
9#>#& ) = -
D
N
E
E1
NOTE 1
12
b
e
c
A
A1
A2
L1 L
φ
* ,<?1
2009 Microchip Technology Inc. DS21711J-page 19
24AA01/24LC01B
," !*-, , !
!"#$%&"' ()"&'"!&)&#*&&&#
'!!#.#&"#'#%!&"!!#%!&"!!!&$#''!#
- '!#&.0
1,2 1!'!&$& "!**&"&&!
.32 %'!("!"*&"&&(%%'&"!!
3&'!&"&4#*!(!!&4%&&#&
&&255***''54
6&! 99..
'!9'&! 7 7: ;
7"')%! 7 <
& ?1,
: 8& = =
##44!! <
&#%% =
: >#& . 1,
##4>#& . -1,
: 9& -1,
3&9& 9 ? <
3&& 9 .3
3& B = <B
9#4!! < = -
9#>#& ) =
D
N
E
E1
NOTE 1
12
e
b
A
A1
A2
c
L1 L
φ
* ,1
24AA01/24LC01B
DS21711J-page 20 2009 Microchip Technology Inc.
. !(""!( !(/
'!!#.#&"#'#%!&"!!#%!&"!!!&$#''!#
'!#&.0
1,2 1!'!&$& "!**&"&&!
3&'!&"&4#*!(!!&4%&&#&
&&255***''54
6&! 99..
'!9'&! 7 7: ;
7"')%! 7
9#& 1,
:"&!#9#& 1,
: 8& =
##44!! < = -
&#%% =
: >#& . = -
##4>#& . - = <
: 9& = -
3&9& 9 = ?
3&& 9 - = <
3& B = -B
9#4!! < = ?
9#>#& ) =
φ
N
b
E
E1
D
123
e
e1
A
A1
A2 c
L
L1
* ,1
2009 Microchip Technology Inc. DS21711J-page 21
24AA01/24LC01B
. !(""( '0
'!!#.#&"#'#%!&"!!#%!&"!!!&$#''!#
'!#&.0
1,2 1!'!&$& "!**&"&&!
3&'!&"&4#*!(!!&4%&&#&
&&255***''54
6&! 99..
'!9'&! 7 7: ;
7"')%! 7
& ?1,
: 8& < =
##44!! < =
&#%% =
: >#& . <
##4>#& . -
: 9& <
3&9& 9 ?
9#4!! < = ?
9#>#& ) =
D
b
1
23
E1
E
45
ee
c
L
A1
AA2
* ,?1
24AA01/24LC01B
DS21711J-page 22 2009 Microchip Technology Inc.
3&'!&"&4#*!(!!&4%&&#&
&&255***''54
2009 Microchip Technology Inc. DS21711J-page 23
24AA01/24LC01B
1$*-,'/22%&1
!"#$%&"' ()"&'"!&)&#*&&&#
4' '$!#&)!&#!
- 4!!*!"&#
'!#&.0
1,2 1!'!&$& "!**&"&&!
.32 %'!("!"*&"&&(%%'&"!!
3&'!&"&4#*!(!!&4%&&#&
&&255***''54
6&! 99..
'!9'&! 7 7: ;
7"')%! 7 <
& 1,
: 8& <
&#%%
,&&4!! - .3
: 9& 1,
: >#& . -1,
.$!##9& - =
.$!##>#& . =
,&&>#& ) -
,&&9& 9 -
,&&&.$!## C = =
D
N
E
NOTE 1
12
EXPOSED PAD
NOTE 1
21
D2
K
L
E2
N
e
b
A3 A1
A
NOTE 2
BOTTOM VIEW
TOP VIEW
* ,-,
24AA01/24LC01B
DS21711J-page 24 2009 Microchip Technology Inc.
1$*-,'/22%&1
3&'!&"&4#*!(!!&4%&&#&
&&255***''54
2009 Microchip Technology Inc. DS21711J-page 25
24AA01/24LC01B
1$*-,/22%0.(1
3&'!&"&4#*!(!!&4%&&#&
&&255***''54
24AA01/24LC01B
DS21711J-page 26 2009 Microchip Technology Inc.
1$*-,/22%0.(1
3&'!&"&4#*!(!!&4%&&#&
&&255***''54
2009 Microchip Technology Inc. DS21711J-page 27
24AA01/24LC01B
APPENDIX A: REVISION HISTORY
Revision C
Corrections to Section 1.0, Electrical Characteristics.
Section 9.1, 24LC01B standard marking code.
Revision D
Added DFN package.
Revision E
Revi se d F ig ur e 3 -2 C o ntr o l By te Al l oc ati o n; Fi g ure 4- 1
Byte Write; Figure 4-2 Page Write; Section 6.0 Write
Protectio n; Figure 7-1 Curre nt Address Read ; Figure 7-
2 Random Read; Figure 7-3 Sequential Read.
Revision F (01/2007)
Revised Device Selection Table; Revised Features
Section; Changed 1.8V to 1.7V; Revised Ta ble 1-1,
1-2, 8-1; Replaced Package Drawings; Revised
Product ID System.
Revision G (03/2007)
Replaced Package Drawings (Rev. AM).
Revision H (08/2008)
Added SC-70 Package; Updated Package Drawings.
Revision J (01/2009)
Added TDFN Package; Updated Package Drawings.
24AA01/24LC01B
DS21711J-page 28 2009 Microchip Technology Inc.
NOTES:
2009 Microchip Technology Inc. DS21711J-page 29
24AA01/24LC01B
THE MICROCHIP WEB SITE
Microc hip pro vides onl ine s upport v ia our W WW site at
www.microchi p.c om . Thi s web si te i s us ed as a m ean s
to make files and information easily available to
customers. Accessible by using your favorite Internet
browser, the web site contains the following
information:
•Product Support – Data sheets and errata,
application notes and sample programs, design
resources, user’s guides and hardware support
documents, latest software releases and archived
software
•General Technical Support – Frequently Asked
Questions (FAQ), technical support requests,
online dis cu ss io n gr oups, Microchip con sultant
program member listing
•Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of
Microchip sales offices, distributors and factory
representatives
CUSTOMER CHANGE NOTIFICATION
SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a
specif ied produ ct family or develo pment tool of interes t.
To register, access the Microchip web site at
www.microchip.com, click on Customer Change
Notification and follow the registration instructions.
CUSTOMER SUPP ORT
Users of Microchip products can receive assistance
through several channels:
• Distributor or Representative
• Local Sales Office
• Field Application Engineer (FAE)
• Technical Support
• Development Systems Information Line
Customers should contact their distributor,
representative or field application engineer (FAE) for
support. Local sales offices are also available to help
customers. A listing of sales offices and locations is
included in the back of this document.
Technical s upport is a vailable through the web si te
at: http://support.microchip.com
24AA01/24LC01B
DS21711J-page 30 2009 Microchip Technology Inc.
READER RESP ONSE
It is ou r intentio n to provide you w it h th e b es t do cument ation po ss ib le to ensure suc c es sfu l u se of y ou r M ic roc hip prod-
uct. If you wi sh to prov ide you r comment s on org aniza tion, clar ity, subj ect matte r , and ways i n which o ur docum entatio n
can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150.
Please list the following information, and use this outline to provide us with your comments about this document.
To: Technical Publications Manager
RE: Reader Response Total Pages Sent ________
From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
Application (optional):
Would you like a reply? Y N
Device: Literature Number:
Questions:
FAX: (______) _________ - _________
DS21711J24AA01/24LC01B
1. What are the best featu res of this document ?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
2009 Microchip Technology Inc. DS21711J-page31
24AA01/24LC01B
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO. X/XX
PackageTemperature
Range
Device
Device: 24AA01: = 1.7V, 1 Kbit I2C™ Serial EEPROM
24AA01T: = 1. 7V, 1 Kbit I2C Se rial EEPROM
(Tape and Reel)
24LC01B: = 2.5V, 1 Kbit I2C Seria l EEPROM
24LC01BT: = 2.5V, 1 Kbit I2C Ser ial EE PR OM
(Tape and Reel)
Temperature
Range: I = -40°C to +85°C
E = -40°C to +125°C
Package: MC = 2x3 DFN, 8-lead
P = Plastic DIP (300 mil body), 8-lead
SN = Plastic SOIC (3.90 mm body), 8-lead
ST = Pla st ic TSSOP (4.4 mm), 8-lead
MS = Plastic Micro Small Outline (MSOP), 8-lead
OT = SOT-23, 5-lead (Tape and Reel only)
LT = SC-70, 5-lead (Tape and Reel only)
MNY(1)=TDFN, (2x3x0.75 mm body), 8-lead
Examples:
a) 24AA01-I/P: Industrial Temperature,1.7V
PDIP package
b) 24AA01-I/SN: Industrial Temperature,
1.7V, SOIC package
c) 24AA01T-I/OT: Industrial Temperature,
1.7V, SOT-23 package, tape and reel
d) 24LC01B-I/P: Industrial Temperature,
2.5V, PDIP package
e) 24LC01B-E/SN: Extended Temperature,
2.5V, SOIC package
f) 24LC01BT- I/LT: Industrial Temperature,
1.7V, SC-70 package, tape and reel
Note 1: "Y" indicates a Nickel Palladium Gold (NiPdAu) finish.
24AA01/24LC01B
DS21711J-page 32 2009 Microchip Technology Inc.
NOTES:
2009 Microchip Technology Inc. DS21711J-page 33
Information contained in this publication regarding device
applications and the like is provided only for your con ve nience
and may be superseded by u pdates. It is y our respo ns ibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, Accuron,
dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro,
PICSTA RT, rfPI C, SmartShunt and UNI/O are registered
trademarks of Microchip Technology Inc orporated in the
U.S.A. and other countries.
FilterLab, Linear Active Thermistor, MXDEV, MXLAB,
SEEV AL, SmartSensor and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, In-Circuit Serial
Prog ra m ming, IC S P, ICE PI C , M i n di , MiWi, MPASM , MPLAB
Certified logo, MPLIB, MPLINK, mTouch, PICkit, PICDEM,
PICDEM.net, PICtail , PIC32 logo, PowerCal, PowerInfo,
PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total
Endurance, WiperLock and ZENA are trademarks of
Microchip Technology Incorporat ed in the U.S.A. and other
countries.
SQTP is a service mark of Microchip T echnology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2009, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Note the following details of the code protection feature on Microchip devices:
• Microchip products meet the specification contained in their particular Microchip Data Sheet.
• Microchip believes that i ts family of products is one of the most secure families of its kind on t he market today, when used in the
intended manner and under normal conditions.
• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contai ned in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
• Microchip is willing to work with the customer who is concerned about the integrity of their code.
• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is c onstantly evolving. We a t Microc hip are co m mitted to continuously improving the code prot ect ion featur es of our
products. Attempts to break Microchip’ s code protection feature may be a violation of the Digital Millennium Copyright Act. If such act s
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code ho pping
devices, Serial EEPROMs, microperiph erals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
DS21711J-page 34 2009 Microchip Technology Inc.
AMERICAS
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technica l Support:
http://support.microchip.com
Web Address:
www.microchip.com
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasc a , IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
Los A n ge les
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
ASIA/PACIFIC
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
Australia - Sydney
Tel: 61-2-9868-67 33
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8528-2 100
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5 511
Fax: 86-28-8665-7889
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
China - Nanjing
Tel: 86-25-8473-2 460
Fax: 86-25-8473-2470
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
China - Shanghai
Tel: 86-21-5407-5 533
Fax: 86-21-5407-5066
China - Shenyang
Tel: 86-24-2334-2 829
Fax: 86-24-2334-2393
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
China - Wuhan
Tel: 86-27-5980-5 300
Fax: 86-27-5980-5118
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
China - Xian
Tel: 86-29-8833-7 252
Fax: 86-29-8833-7256
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
ASIA/PACIFIC
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4080
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Taiwan - Hsin Chu
Tel: 886-3-572-9526
Fax: 886-3-572-6459
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
Thailand - Bangko k
Tel: 66-2-694-1351
Fax: 66-2-694-1350
EUROPE
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Cop e nha gen
Tel: 45-4450-2828
Fax: 45-4485-2829
France - Paris
Tel: 33-1-69-53 -63-20
Fax: 33-1-69-30-90-79
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-14 4-44
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08 -91
UK - Wokingham
Tel: 44-118-921- 5869
Fax: 44-118-921-5820
WORLDWIDE SALES AND SERVICE
02/04/09
