Freescale
Data Sheet: Technical Data
Document Number: MCF52259
Rev. 5, 5/2012
© Freescale, Inc., 2011, 2012. All rights reserved.
Freescale reserves the right to change the detail specifications as may be required to permit
improvements in the design of its products.
MCF52259
144 LQFP
20 mm x 20 mm
144 MAPBGA
13 mm x 13 mm
100 LQFP
14 mm x 14 mm
The MCF52259 microcontroller family (MCF52252,
MCF52254, MCF52255, MCF52256, MCF52258, and
MCF52259 devices) is a member of the ColdFire family of
reduced instruction set computing (RISC) microprocessors.
This document provides an overview of the 32-bit MCF52259
microcontroller, focusing on its highly integrated and diverse
feature set.
This 32-bit device is based on the Version 2 ColdFire core
operating at a frequency up to 80 MHz, offering high
performance and low power consumption. On-chip memories
connected tightly to the processor core include up to 512 KB
of flash memory and 64 KB of static random access memory
(SRAM). On-chip modules include:
V2 ColdFire core delivering 76 MIPS (Dhrystone 2.1) at
80 MHz running from internal flash memory with
Enhanced Multiply Accumulate (MAC) Unit and hardware
divider
Cryptography Acceleration Unit (CAU).
Fast Ethernet controller (FEC)
Mini-FlexBus external bus interface available on 144 pin
packages
Universal Serial Bus On-The-Go (USBOTG)
USB Transceiver
FlexCAN controller area network (CAN) module
Three universal asynchronous/synchronous
receiver/transmitters (UARTs)
Two inter-integrated circuit (I2C) bus interface modules
Queued serial peripheral interface (QSPI) module
Eight-channel 12-bit fast analog-to-digital converter
(ADC) with simultaneous sampling
Four-channel direct memory access (DMA) controller
Four 32-bit input capture/output compare timers with
DMA support (DTIM)
Four-channel general-purpose timer (GPT) capable of
input capture/output compare, pulse width modulation
(PWM), pulse-code modulation (PCM), and pulse
accumulation
Eight-channel/Four-channel, 8-bit/16-bit pulse width
modulation timer
Two 16-bit periodic interrupt timers (PITs)
Real-time clock (RTC) module with 32 kHz crystal
Programmable software watchdog timer
Secondary watchdog timer with independent clock
Interrupt controller capable of handling 57 sources
Clock module with 8 MHz on-chip relaxation oscillator
and integrated phase-locked loop (PLL)
Test access/debug port (JTAG, BDM)
MCF52259 ColdFire
Microcontroller
Supports MCF52252, MCF52254,
MCF52255, MCF52256, MCF52258,
MCF52259
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale2
Table of Contents
1 Family Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1.1 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
2.1 Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
2.2 Current Consumption . . . . . . . . . . . . . . . . . . . . . . . . . .25
2.3 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . .26
2.4 Flash Memory Characteristics . . . . . . . . . . . . . . . . . . .28
2.5 EzPort Electrical Specifications . . . . . . . . . . . . . . . . . .29
2.6 ESD Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
2.7 DC Electrical Specifications . . . . . . . . . . . . . . . . . . . . .30
2.8 Clock Source Electrical Specifications . . . . . . . . . . . . .31
2.9 USB Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
2.10 Mini-FlexBus External Interface Specifications . . . . . . 32
2.11 Fast Ethernet Timing Specifications . . . . . . . . . . . . . . 33
2.12 General Purpose I/O Timing . . . . . . . . . . . . . . . . . . . . 35
2.13 Reset Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2.14 I2C Input/Output Timing Specifications . . . . . . . . . . . . 37
2.15 Analog-to-Digital Converter (ADC) Parameters. . . . . . 38
2.16 Equivalent Circuit for ADC Inputs . . . . . . . . . . . . . . . . 39
2.17 DMA Timers Timing Specifications . . . . . . . . . . . . . . . 40
2.18 QSPI Electrical Specifications . . . . . . . . . . . . . . . . . . . 40
2.19 JTAG and Boundary Scan Timing . . . . . . . . . . . . . . . . 40
2.20 Debug AC Timing Specifications . . . . . . . . . . . . . . . . . 43
3 Package Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
MCF52259 ColdFire Microcontroller, Rev. 5
Family Configurations
Freescale3
1 Family Configurations
Table 1. MCF52259 Family Configurations
Module 52252 52254 52255 52256 52258 52259
Version 2 ColdFire Core with eMAC
(Enhanced multiply-accumulate unit) and CAU
(Cryptographic acceleration unit)

System Clock up to 66 or 80 MHz1
166 MHz = 63 MIPS; 80 MHz = 76 MIPS
up to
80 MHz1up to 66 or 80 MHz1up to
80 MHz1
Performance (Dhrystone 2.1 MIPS) up to 63 or 76
Flash 256 KB 512 KB 512 KB 256 KB 512 KB 512 KB
Static RAM (SRAM) 32 KB 64 KB 64 KB 32 / 64 KB 64 KB 64 KB
Two Interrupt Controllers (INTC) 
Fast Analog-to-Digital Converter (ADC) 
USB On-The-Go (USB OTG) 
Mini-FlexBus external bus interface 
Fast Ethernet Controller (FEC) 
Random Number Generator and
Cryptographic Acceleration Unit (CAU) —— ——
FlexCAN 2.0B Module Varies Varies Varies Varies
Four-channel Direct-Memory Access (DMA) 
Software Watchdog Timer (WDT) 
Secondary Watchdog Timer 
Two-channel Periodic Interrupt Timer (PIT)222222
Four-Channel General Purpose Timer (GPT) 
32-bit DMA Timers 444444
QSPI 
UART(s) 333333
I2C 222222
Eight/Four-channel 8/16-bit PWM Timer 
General Purpose I/O Module (GPIO) 
Chip Configuration and Reset Controller Module 
Background Debug Mode (BDM) 
JTAG - IEEE 1149.1 Test Access Port 
Package 100 LQFP 144 LQFP or 144 MAPBGA
Family Configurations
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 4
1.1 Block Diagram
Figure 1 shows a top-level block diagram of the device. Package options for this family are described later in this document.
Figure 1. MCF52259 Block Diagram
1.2 Features
1.2.1 Feature Overview
The MCF52259 family includes the following features:
Version 2 ColdFire variable-length RISC processor core
Static operation
32-bit address and data paths on-chip
Mini-FlexBus
Arbiter Interrupt
Controllers
QSPI
UARTs
0–2
I2C
DTIMs
0–3
V2 ColdFire CPU
IFP OEP EMAC
4 ch DMA
MUX
JTAG
TA P
up to 64 KB
SRAM
(4K16)4
up to 512 KB
Flash
(64K16)4
PORTS
(GPIO)
CCM, RSTIN
RSTOUT
I2Cs
UARTs
DTINn/DTOUTn
CANRX
JTAG_EN
ADC
AN[7:0]
VRH VRL
PLL
CLKGEN
EXTAL XTAL CLKOUT
GPT PWM
CANTX
PMM
PADI – Pin Muxing
EzPort EzPCS
PWMn
USB
FEC
EzPQ
EzPD EzPCK
RTC
CAU
To / Fr o m
Reset
Mini-FlexBus
PA D I
USB
PITs
0–1
FlexCAN Edge
Port
0–1
RNGA
Watchdog
Timer
GPTn
QSPI
IRQn
FEC
EzPort
To/From PADI
To/From PADI
To / Fr o m
PA D I
JTAG/BDM
MCF52259 ColdFire Microcontroller, Rev. 5
Family Configurations
Freescale5
Up to 80 MHz processor core frequency
40 MHz or 33 MHz peripheral bus frequency
Sixteen general-purpose, 32-bit data and address registers
Implements ColdFire ISA_A with extensions to support the user stack pointer register and four new instructions
for improved bit processing (ISA_A+)
Enhanced Multiply-Accumulate (EMAC) unit with four 32-bit accumulators to support 1616 32 or
3232 48 operations
Cryptographic Acceleration Unit (CAU)
Tightly-coupled coprocessor to accelerate software-based encryption and message digest functions
Support for DES, 3DES, AES, MD5, and SHA-1 algorithms
System debug support
Real-time trace for determining dynamic execution path
Background debug mode (BDM) for in-circuit debugging (DEBUG_B+)
Real-time debug support, with six hardware breakpoints (4 PC, 1 address and 1 data) configurable into a 1- or
2-level trigger
On-chip memories
Up to 64 KB dual-ported SRAM on CPU internal bus, supporting core, DMA, and USB access with standby
power supply support for the first 16 KB
Up to 512 KB of interleaved flash memory supporting 2-1-1-1 accesses
Power management
Fully static operation with processor sleep and whole chip stop modes
Rapid response to interrupts from the low-power sleep mode (wake-up feature)
Clock enable/disable for each peripheral when not used (except backup watchdog timer)
Software controlled disable of external clock output for low-power consumption
FlexCAN 2.0B module
Based on and includes all existing features of the Freescale TouCAN module
Full implementation of the CAN protocol specification version 2.0B
Standard data and remote frames (up to 109 bits long)
Extended data and remote frames (up to 127 bits long)
Zero to eight bytes data length
Programmable bit rate up to 1 Mbit/s
Flexible message buffers (MBs), totalling up to 16 message buffers of 0–8 byte data length each, configurable as
Rx or Tx, all supporting standard and extended messages
Unused MB space can be used as general purpose RAM space
Listen-only mode capability
Content-related addressing
No read/write semaphores
Three programmable mask registers: global for MBs 0–13, special for MB14, and special for MB15
Programmable transmit-first scheme: lowest ID or lowest buffer number
Time stamp based on 16-bit free-running timer
Global network time, synchronized by a specific message
Maskable interrupts
Universal Serial Bus On-The-Go (USB OTG) dual-mode host and device controller
Full-speed / low-speed host controller
USB 1.1 and 2.0 compliant full-speed / low speed device controller
16 bidirectional end points
Family Configurations
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 6
DMA or FIFO data stream interfaces
Low power consumption
OTG protocol logic
Fast Ethernet controller (FEC)
10/100 BaseT/TX capability, half duplex or full duplex
On-chip transmit and receive FIFOs
Built-in dedicated DMA controller
Memory-based flexible descriptor rings
Mini-FlexBus
External bus interface available on 144 pin packages
Supports glueless interface with 8-bit ROM/flash/SRAM/simple slave peripherals. Can address up to 2 MB of
addresses
2 chip selects (FB_CS[1:0])
Non-multiplexed mode: 8-bit dedicated data bus, 20-bit address bus
Multiplexed mode: 16-bit data and 20-bit address bus
FB_CLK output to support synchronous memories
Programmable base address, size, and wait states to support slow peripherals
Operates at up to 40 MHz (bus clock) in 1:2 mode or up to 80 MHz (core clock) in 1:1 mode
Three universal asynchronous/synchronous receiver transmitters (UARTs)
16-bit divider for clock generation
Interrupt control logic with maskable interrupts
DMA support
Data formats can be 5, 6, 7, or 8 bits with even, odd, or no parity
Up to two stop bits in 1/16 increments
Error-detection capabilities
Modem support includes request-to-send (RTS) and clear-to-send (CTS) lines for two UARTs
Transmit and receive FIFO buffers
Two I2C modules
Interchip bus interface for EEPROMs, LCD controllers, A/D converters, and keypads
Fully compatible with industry-standard I2C bus
Master and slave modes support multiple masters
Automatic interrupt generation with programmable level
Queued serial peripheral interface (QSPI)
Full-duplex, three-wire synchronous transfers
Up to three chip selects available
Master mode operation only
Programmable bit rates up to half the CPU clock frequency
Up to 16 pre-programmed transfers
Fast analog-to-digital converter (ADC)
Eight analog input channels
12-bit resolution
Minimum 1.125 s conversion time
Simultaneous sampling of two channels for motor control applications
Single-scan or continuous operation
Optional interrupts on conversion complete, zero crossing (sign change), or under/over low/high limit
MCF52259 ColdFire Microcontroller, Rev. 5
Family Configurations
Freescale7
Unused analog channels can be used as digital I/O
Four 32-bit timers with DMA support
12.5 ns resolution at 80 MHz
Programmable sources for clock input, including an external clock option
Programmable prescaler
Input capture capability with programmable trigger edge on input pin
Output compare with programmable mode for the output pin
Free run and restart modes
Maskable interrupts on input capture or output compare
DMA trigger capability on input capture or output compare
Four-channel general purpose timer
16-bit architecture
Programmable prescaler
Output pulse-widths variable from microseconds to seconds
Single 16-bit input pulse accumulator
Toggle-on-overflow feature for pulse-width modulator (PWM) generation
One dual-mode pulse accumulation channel
Pulse-width modulation timer
Support for PCM mode (resulting in superior signal quality compared to conventional PWM)
Operates as eight channels with 8-bit resolution or four channels with 16-bit resolution
Programmable period and duty cycle
Programmable enable/disable for each channel
Software selectable polarity for each channel
Period and duty cycle are double buffered. Change takes effect when the end of the current period is reached
(PWM counter reaches zero) or when the channel is disabled.
Programmable center or left aligned outputs on individual channels
Four clock sources (A, B, SA, and SB) provide for a wide range of frequencies
Emergency shutdown
Two periodic interrupt timers (PITs)
16-bit counter
Selectable as free running or count down
Real-Time Clock (RTC)
Maintains system time-of-day clock
Provides stopwatch and alarm interrupt functions
Standby power supply (Vstby) keeps the RTC running when the system is shut down
Software watchdog timer
32-bit counter
Low-power mode support
Backup watchdog timer (BWT)
Independent timer that can be used to help software recover from runaway code
16-bit counter
Low-power mode support
Clock generation features
Crystal, on-chip trimmed relaxation oscillator, or external oscillator reference options
Trimmed relaxation oscillator
Family Configurations
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 8
Pre-divider capable of dividing the clock source frequency into the PLL reference frequency range
System can be clocked from PLL or directly from crystal oscillator or relaxation oscillator
Low power modes supported
—2
n (0 n15) low-power divider for extremely low frequency operation
Interrupt controller
Uniquely programmable vectors for all interrupt sources
Fully programmable level and priority for all peripheral interrupt sources
Seven external interrupt signals with fixed level and priority
Unique vector number for each interrupt source
Ability to mask any individual interrupt source or all interrupt sources (global mask-all)
Support for hardware and software interrupt acknowledge (IACK) cycles
Combinatorial path to provide wake-up from low-power modes
DMA controller
Four fully programmable channels
Dual-address transfer support with 8-, 16-, and 32-bit data capability, along with support for 16-byte (432-bit)
burst transfers
Source/destination address pointers that can increment or remain constant
24-bit byte transfer counter per channel
Auto-alignment transfers supported for efficient block movement
Bursting and cycle-steal support
Software-programmable DMA requests for the UARTs (3) and 32-bit timers (4)
Channel linking support
Reset
Separate reset in and reset out signals
Seven sources of reset:
Power-on reset (POR)
External
–Software
Watchdog
Loss of clock / loss of lock
Low-voltage detection (LVD)
–JTAG
Status flag indication of source of last reset
Chip configuration module (CCM)
System configuration during reset
Selects one of six clock modes
Configures output pad drive strength
Unique part identification number and part revision number
General purpose I/O interface
Up to 56 bits of general purpose I/O on 100-pin package
Up to 96 bits of general purpose I/O on 144-pin package
Bit manipulation supported via set/clear functions
Programmable drive strengths
Unused peripheral pins may be used as extra GPIO
JTAG support for system level board testing
MCF52259 ColdFire Microcontroller, Rev. 5
Family Configurations
Freescale9
1.2.2 V2 Core Overview
The version 2 ColdFire processor core is comprised of two separate pipelines decoupled by an instruction buffer. The two-stage
instruction fetch pipeline (IFP) is responsible for instruction-address generation and instruction fetch. The instruction buffer is
a first-in-first-out (FIFO) buffer that holds prefetched instructions awaiting execution in the operand execution pipeline (OEP).
The OEP includes two pipeline stages. The first stage decodes instructions and selects operands (DSOC); the second stage
(AGEX) performs instruction execution and calculates operand effective addresses, if needed.
The V2 core implements the ColdFire instruction set architecture revision A+ with support for a separate user stack pointer
register and four new instructions to assist in bit processing. Additionally, the core includes the enhanced multiply-accumulate
(EMAC) unit for improved signal processing capabilities. The EMAC implements a three-stage arithmetic pipeline, optimized
for 32x32 bit operations, with support for four 48-bit accumulators. Supported operands include 16- and 32-bit signed and
unsigned integers, signed fractional operands, and a complete set of instructions to process these data types. The EMAC
provides support for execution of DSP operations within the context of a single processor at a minimal hardware cost.
1.2.3 Integrated Debug Module
The ColdFire processor core debug interface is provided to support system debugging with low-cost debug and emulator
development tools. Through a standard debug interface, access to debug information and real-time tracing capability is provided
on 144-lead packages. This allows the processor and system to be debugged at full speed without the need for costly in-circuit
emulators.
The on-chip breakpoint resources include a total of nine programmable 32-bit registers: an address and an address mask register,
a data and a data mask register, four PC registers, and one PC mask register. These registers can be accessed through the
dedicated debug serial communication channel or from the processors supervisor mode programming model. The breakpoint
registers can be configured to generate triggers by combining the address, data, and PC conditions in a variety of single- or
dual-level definitions. The trigger event can be programmed to generate a processor halt or initiate a debug interrupt exception.
This device implements revision B+ of the ColdFire Debug Architecture.
The processors interrupt servicing options during emulator mode allow real-time critical interrupt service routines to be
serviced while processing a debug interrupt event. This ensures the system continues to operate even during debugging.
To support program trace, the V2 debug module provides processor status (PST[3:0]) and debug data (DDATA[3:0]) ports.
These buses and the PSTCLK output provide execution status, captured operand data, and branch target addresses defining
processor activity at the CPU’s clock rate. The device includes a new debug signal, ALLPST. This signal is the logical AND of
the processor status (PST[3:0]) signals and is useful for detecting when the processor is in a halted state (PST[3:0] = 1111).
The full debug/trace interface is available only on the 144-pin packages. However, every product features the dedicated debug
serial communication channel (DSI, DSO, DSCLK) and the ALLPST signal.
1.2.4 JTAG
The processor supports circuit board test strategies based on the Test Technology Committee of IEEE and the Joint Test Action
Group (JTAG). The test logic includes a test access port (TAP) consisting of a 16-state controller, an instruction register, and
three test registers (a 1-bit bypass register, a boundary-scan register, and a 32-bit ID register). The boundary scan register links
the device’s pins into one shift register. Test logic, implemented using static logic design, is independent of the device system
logic.
The device implementation can:
Perform boundary-scan operations to test circuit board electrical continuity
Sample system pins during operation and transparently shift out the result in the boundary scan register
Bypass the device for a given circuit board test by effectively reducing the boundary-scan register to a single bit
Disable the output drive to pins during circuit-board testing
Drive output pins to stable levels
Family Configurations
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 10
1.2.5 On-Chip Memories
1.2.5.1 SRAM
The dual-ported SRAM module provides a general-purpose 64 KB memory block that the ColdFire core can access in a single
cycle. The location of the memory block can be set to any 64 KB boundary within the 4 GB address space. This memory is ideal
for storing critical code or data structures and for use as the system stack. Because the SRAM module is physically connected
to the processor's high-speed local bus, it can quickly service core-initiated accesses or memory-referencing commands from
the debug module.
The SRAM module is also accessible by the DMA, FEC, and USB. The dual-ported nature of the SRAM makes it ideal for
implementing applications with double-buffer schemes, where the processor and a DMA device operate in alternate regions of
the SRAM to maximize system performance.
1.2.5.2 Flash Memory
The ColdFire flash module (CFM) is a non-volatile memory (NVM) module that connects to the processors high-speed local
bus. The CFM is constructed with four banks of 64 KB16-bit flash memory arrays to generate 512 KB of 32-bit flash memory.
These electrically erasable and programmable arrays serve as non-volatile program and data memory. The flash memory is ideal
for program and data storage for single-chip applications, allowing for field reprogramming without requiring an external high
voltage source. The CFM interfaces to the ColdFire core through an optimized read-only memory controller that supports
interleaved accesses from the 2-cycle flash memory arrays. A backdoor mapping of the flash memory is used for all program,
erase, and verify operations, as well as providing a read datapath for the DMA. Flash memory may also be programmed via the
EzPort, which is a serial flash memory programming interface that allows the flash memory to be read, erased and programmed
by an external controller in a format compatible with most SPI bus flash memory chips.
1.2.6 Cryptographic Acceleration Unit
The MCF52235 device incorporates two hardware accelerators for cryptographic functions. First, the CAU is a coprocessor
tightly-coupled to the V2 ColdFire core that implements a set of specialized operations to increase the throughput of
software-based encryption and message digest functions, specifically the DES, 3DES, AES, MD5 and SHA-1 algorithms.
Second, a random number generator provides FIPS-140 compliant 32-bit values to security processing routines. Both modules
supply critical acceleration to software-based cryptographic algorithms at a minimal hardware cost.
1.2.7 Power Management
The device incorporates several low-power modes of operation entered under program control and exited by several external
trigger events. An integrated power-on reset (POR) circuit monitors the input supply and forces an MCU reset as the supply
voltage rises. The low voltage detector (LVD) monitors the supply voltage and is configurable to force a reset or interrupt
condition if it falls below the LVD trip point. The RAM standby switch provides power to RAM when the supply voltage to the
chip falls below the standby battery voltage.
1.2.8 FlexCAN
The FlexCAN module is a communication controller implementing version 2.0 of the CAN protocol parts A and B. The CAN
protocol can be used as an industrial control serial data bus, meeting the specific requirements of reliable operation in a harsh
EMI environment with high bandwidth. This instantiation of FlexCAN has 16 message buffers.
MCF52259 ColdFire Microcontroller, Rev. 5
Family Configurations
Freescale11
1.2.9 Mini-FlexBus
A multi-function external bus interface called the Mini-FlexBus is provided on the device with basic functionality of interfacing
to slave-only devices with a maximum slave bus frequency up to 40 MHz in 1:2 mode and 80 MHz in 1:1 mode. It can be
directly connected to the following asynchronous or synchronous devices with little or no additional circuitry:
External ROMs
Flash memories
Programmable logic devices
Other simple target (slave) devices
The Mini-FlexBus is a subset of the FlexBus module found on higher-end ColdFire microprocessors. The Mini-FlexBus
minimizes package pin-outs while maintaining a high level of configurability and functionality.
1.2.10 USB On-The-Go Controller
The device includes a Universal Serial Bus On-The-Go (USB OTG) dual-mode controller. USB is a popular standard for
connecting peripherals and portable consumer electronic devices such as digital cameras and handheld computers to host PCs.
The OTG supplement to the USB specification extends USB to peer-to-peer application, enabling devices to connect directly
to each other without the need for a PC. The dual-mode controller on the device can act as a USB OTG host and as a USB
device. It also supports full-speed and low-speed modes.
1.2.11 Fast Ethernet Controller (FEC)
The Ethernet media access controller (MAC) supports 10 and 100 Mbps Ethernet/IEEE 802.3 networks. An external transceiver
interface and transceiver function are required to complete the interface to the media. The FEC supports three different standard
MAC-PHY (physical) interfaces for connection to an external Ethernet transceiver. The FECs supports the 10/100 Mbps MII,
and the 10 Mbps-only 7-wire interface.
1.2.12 UARTs
The device has three full-duplex UARTs that function independently. The three UARTs can be clocked by the system bus clock,
eliminating the need for an external clock source. On smaller packages, the third UART is multiplexed with other digital I/O
functions.
1.2.13 I2C Bus
The processor includes two I2C modules. The I2C bus is an industry-standard, two-wire, bidirectional serial bus that provides
a simple, efficient method of data exchange and minimizes the interconnection between devices. This bus is suitable for
applications requiring occasional communications over a short distance between many devices.
1.2.14 QSPI
The queued serial peripheral interface (QSPI) provides a synchronous serial peripheral interface with queued transfer capability.
It allows up to 16 transfers to be queued at once, minimizing the need for CPU intervention between transfers.
1.2.15 Fast ADC
The fast ADC consists of an eight-channel input select multiplexer and two independent sample and hold (S/H) circuits feeding
separate 12-bit ADCs. The two separate converters store their results in accessible buffers for further processing. Signals on the
SYNCA and SYNCB pins initiate an ADC conversion.
Family Configurations
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 12
The ADC can be configured to perform a single scan and halt, a scan when triggered, or a programmed scan sequence repeatedly
until manually stopped.
The ADC can be configured for sequential or simultaneous conversion. When configured for sequential conversions, up to eight
channels can be sampled and stored in any order specified by the channel list register. Both ADCs may be required during a
scan, depending on the inputs to be sampled.
During a simultaneous conversion, both S/H circuits are used to capture two different channels at the same time. This
configuration requires that a single channel may not be sampled by both S/H circuits simultaneously.
Optional interrupts can be generated at the end of the scan sequence if a channel is out of range (measures below the low
threshold limit or above the high threshold limit set in the limit registers) or at several different zero crossing conditions.
1.2.16 DMA Timers (DTIM0–DTIM3)
There are four independent, DMA transfer capable 32-bit timers (DTIM0, DTIM1, DTIM2, and DTIM3) on the device. Each
module incorporates a 32-bit timer with a separate register set for configuration and control. The timers can be configured to
operate from the system clock or from an external clock source using one of the DTINn signals. If the system clock is selected,
it can be divided by 16 or 1. The input clock is further divided by a user-programmable 8-bit prescaler that clocks the actual
timer counter register (TCRn). Each of these timers can be configured for input capture or reference (output) compare mode.
Timer events may optionally cause interrupt requests or DMA transfers.
1.2.17 General Purpose Timer (GPT)
The general purpose timer (GPT) is a four-channel timer module consisting of a 16-bit programmable counter driven by a
seven-stage programmable prescaler. Each of the four channels can be configured for input capture or output compare.
Additionally, channel three, can be configured as a pulse accumulator.
A timer overflow function allows software to extend the timing capability of the system beyond the 16-bit range of the counter.
The input capture and output compare functions allow simultaneous input waveform measurements and output waveform
generation. The input capture function can capture the time of a selected transition edge. The output compare function can
generate output waveforms and timer software delays. The 16-bit pulse accumulator can operate as a simple event counter or a
gated time accumulator.
1.2.18 Periodic Interrupt Timers (PIT0 and PIT1)
The two periodic interrupt timers (PIT0 and PIT1) are 16-bit timers that provide interrupts at regular intervals with minimal
processor intervention. Each timer can count down from the value written in its PIT modulus register or it can be a free-running
down-counter.
1.2.19 Real-Time Clock (RTC)
The Real-Time Clock (RTC) module maintains the system (time-of-day) clock and provides stopwatch, alarm, and interrupt
functions. It includes full clock features: seconds, minutes, hours, days and supports a host of time-of-day interrupt functions
along with an alarm interrupt.
1.2.20 Pulse-Width Modulation (PWM) Timers
The device has an 8-channel, 8-bit PWM timer. Each channel has a programmable period and duty cycle as well as a dedicated
counter. Each of the modulators can create independent continuous waveforms with software-selectable duty rates from 0% to
100%. The timer supports PCM mode, which results in superior signal quality when compared to that of a conventional PWM.
The PWM outputs have programmable polarity, and can be programmed as left aligned outputs or center aligned outputs. For
MCF52259 ColdFire Microcontroller, Rev. 5
Family Configurations
Freescale13
higher period and duty cycle resolution, each pair of adjacent channels ([7:6], [5:4], [3:2], and [1:0]) can be concatenated to
form a single 16-bit channel. The module can, therefore, be configured to support 8/0, 6/1, 4/2, 2/3, or 0/4 8-/16-bit channels.
1.2.21 Software Watchdog Timer
The watchdog timer is a 32-bit timer that facilitates recovery from runaway code. The watchdog counter is a free-running
down-counter that generates a reset on underflow. To prevent a reset, software must periodically restart the countdown.
1.2.22 Backup Watchdog Timer
The backup watchdog timer is an independent 16-bit timer that, like the software watchdog timer, facilitates recovery from
runaway code. This timer is a free-running down-counter that generates a reset on underflow. To prevent a reset, software must
periodically restart the countdown. The backup watchdog timer can be clocked by either the relaxation oscillator or the system
clock.
1.2.23 Phase-Locked Loop (PLL)
The clock module contains a crystal oscillator, 8 MHz on-chip relaxation oscillator (OCO), phase-locked loop (PLL), reduced
frequency divider (RFD), low-power divider status/control registers, and control logic. To improve noise immunity, the PLL,
crystal oscillator, and relaxation oscillator have their own power supply inputs: VDDPLL and VSSPLL. All other circuits are
powered by the normal supply pins, VDD and VSS.
1.2.24 Interrupt Controllers (INTCn)
The device has two interrupt controllers that supports up to 128 interrupt sources. There are 56 programmable sources, 49 of
which are assigned to unique peripheral interrupt requests. The remaining seven sources are unassigned and may be used for
software interrupt requests.
1.2.25 DMA Controller
The direct memory access (DMA) controller provides an efficient way to move blocks of data with minimal processor
intervention. It has four channels that allow byte, word, longword, or 16-byte burst line transfers. These transfers are triggered
by software explicitly setting a DCRn[START] bit or by the occurrence of certain UART or DMA timer events.
1.2.26 Reset
The reset controller determines the source of reset, asserts the appropriate reset signals to the system, and keeps track of what
caused the last reset. There are seven sources of reset:
External reset input
Power-on reset (POR)
Watchdog timer
Phase locked-loop (PLL) loss of lock / loss of clock
•Software
Low-voltage detector (LVD)
•JTAG
Control of the LVD and its associated reset and interrupt are managed by the reset controller. Other registers provide status flags
indicating the last source of reset and a control bit for software assertion of the RSTO pin.
Family Configurations
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 14
1.2.27 GPIO
Nearly all pins on the device have general purpose I/O capability and are grouped into 8-bit ports. Some ports do not use all
eight bits. Each port has registers that configure, monitor, and control the port pin.
1.2.28 Part Numbers and Packaging
This product is RoHS-compliant. Refer to the product page at freescale.com or contact your sales office for up-to-date RoHS
information.
Table 2. Orderable part number summary
Freescale Part
Number FlexCAN Encryption Speed
(MHz)
Flash
(KB)
SRAM
(KB) Package Temp range
(C)
MCF52252AF80 80 256 32 100 LQFP 0 to +70
MCF52252CAF66 66 -40 to +85
MCF52254AF80 80 512 64 100 LQFP 0 to +70
MCF52254CAF66 66 -40 to +85
MCF52255CAF80  80 512 64 100 LQFP -40 to +85
MCF52256AG80 80
256
32 144 LQFP 0 to +70
MCF52256CAG66 66 64 -40 to +85
MCF52256CVN66 —66 64
144 MAPBGA -40 to +85
MCF52256VN80 80 32 0 to +70
MCF52258AG80 80
512 64
144 LQFP 0 to +70
MCF52258CAG66 66 -40 to +85
MCF52258CVN66 —66 144 MAPBGA -40 to +85
MCF52258VN80 80 0 to +70
MCF52259CAG80  80 512 64 144 LQFP -40 to +85
MCF52259CVN80  144 MAPBGA -40 to +85
MCF52259 ColdFire Microcontroller, Rev. 5
Family Configurations
Freescale15
Figure 2 shows the pinout configuration for the 144 LQFP.
Figure 2. 144 LQFP Pin Assignment
CLKMOD1
CLKMOD0
RSTOUT
RSTIN
FB_D5
FB_D6
FB_D7
FB_OE
FB_A15
VDD
VSS
FB_A16
FB_A17
FB_A18
FB_A19
IRQ3
IRQ5
FEC_RXD3
FEC_RXD2
VDD
VSS
FEC_RXD1
FEC_RXD0
FEC_RXDV
FEC_RXCLK
FEC_RXER
FEC_TXER
FEC_TXCLK
FEC_TXEN
VDD
VSS
FEC_TXD0
FEC_TXD1
FEC_TXD2
FEC_TXD3
FEC_COL
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
FB_D4 1 108 FEC_CRS
FB_A14 2 107 VDDPLL
FB_A13 3 106 EXTAL
FB_A12 4 105 XTAL
FB_A11 5 104 VSSPLL
FB_A10 6 103 IRQ1
VDD 7 102 URXD2
VSS 8 101 UTXD2
TEST 9 100 VDD
RCON 10 99 VSS
TIN0 11 98 URTS2
TIN1 12 97 UCTS2
RTC_EXTAL 13 96 IRQ7
RTC_XTAL 14 95 ICOC2
UCTS0 15 94 ICOC1
UTXD0 16 93 ICOC0
URXD0 17 92 VDD
URTS0 18 91 VSS
TIN3 19 90 PST0
VDD 20 89 PST1
VSS 21 88 PST2
PCS3 22 87 PST3
PCS2 23 86 DDATA3
QSDI 24 85 DDATA2
QSD0 25 84 DDATA1
SCK 26 83 DDATA0
PCS0 27 82 VSSUSB
SCL 28 81 USB_DP
SDA 29 80 USB_DM
VDD 30 79 VDDUSB
VSS 31 78 VSTBY
FB_A9 32 77 AN4
FB_A8 33 76 AN5
FB_A7 34 75 AN6
FB_A6 35 74 AN7
FB_A5 36 73 VDDA
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
FB_ALE
TMS
TRST
TDI
TDO
ALLPST
TCLK
JTAG_EN
FB_RW
FB_D3
FB_D2
VDD
VSS
FB_D1
FB_D0
FB_CS0
FB_A4
FB_A3
FB_A2
FB_A1
FB_A0
ICOC3
VDD
VSS
UCTS1
UTXD1
URXD1
URTS1
TIN2
AN0
AN1
AN2
AN3
VSSA
VRL
VRH
Family Configurations
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 16
Figure 3 shows the pinout configuration for the 100 LQFP.
Figure 3. 100 LQFP Pin Assignments
AN5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
VDD
VSS
TEST
RCON
TIN0
TIN1
RTC_XTAL
UCTS0
UTXD0
URXD0
URTS0
TIN3
VDD
VSS
PCS3
PCS2
QSDI
QSDO
SCK
PCS0
SCL
SDA
VDD
100 LQFP
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
FEC_CRS
VDDPLL
EXTAL
XTAL
VSSPLL
IRQ1
URXD2
UTXD2
VDD
VSS
URTS2
UCTS2
IRQ7
ICOC2
ICOC1
ICOC0
VSSUSB
USB_DP
USB_DM
VDDUSB
VSTBY
AN6
AN7
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
CLKMOD1
CLKMOD0
RSTOUT
RSTIN
IRQ3
IRQ5
FEC_RXD3
FEC_RXD2
VDD
VSS
FEC_RXD1
FEC_RXD0
FEC_RXDV
FEC_RXCLK
FEC_RXER
FEC_TXCLK
FEC_TXEN
VDD
VSS
FEC_TXD0
FEC_TXD1
FEC_TXD2
FEC_TXD3
FEC_COL
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
TMS
TRST
TDI
TDO
ALLPST
TCLK
JTAG_EN
VDD
VSS
ICOC3
VDD
VSS
UCTS1
UTXD1
URXD1
URTS1
TIN2
AN0
AN1
AN2
AN3
VSSA
VRL
VRH
VDDA
VSS
RTC_EXTAL
AN4
FEC_TXER
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale17
Family Configurations
Figure 4 shows the pinout configuration for the 144 MAPBGA.
123456789101112
AVSS RSTOUT RSTIN FB_D6 FB_D7 IRQ3 IRQ5 FEC_
RXD0
FEC_
RXER
FEC_
TXEN
FEC_
TXD3 VSS A
BTEST FB_A14 FB_D4 FB_D5 FB_OE FB_A19 FEC_
RXD1
FEC_
RXCLK
FEC_
TXCLK
FEC_
TXD2 FEC_COL FEC_CRS B
C TIN1 FB_A12 FB_A13 FB_A15 FB_A16 FB_A18 FEC_
RXD2
FEC_
RXDV
FEC_
TXD1 URXD2 VDDPLL EXTAL C
DRTC_
EXTAL TIN0 FB_A11 CLKMOD1 CLKMOD0 FB_A17 FEC_
RXD3
FEC_
TXER
FEC_
TXD0 UTXD2 VSSPLL XTAL D
ERTC_
XTAL UCTS0 FB_A10 RCON VDD VDD VDD VDD IRQ1 URTS2 UCTS2 IRQ7 E
F UTXD0 URXD0 URTS0 TIN3 VDD VSS VSS VSS PST3 DDATA0 DDATA1 ICOC0 F
G QSDO QSDI PCS2 PCS3 VDD VSS VSS VSS DDATA3 PST2 PST1 PST0 G
H SCL SDA SCK PCS0 VDD VDD VDD VSS VSSUSB DDATA2 USB_DM USB_DP H
J FB_A6 FB_A7 FB_A9 FB_A8 FB_D0 FB_A3 VDD TIN2 VDDUSB ICOC2 ICOC1 VSTBY J
KTMS TRST
FB_ALE FB_A5 FB_D2 FB_A4 UCTS1 UTXD1 AN3 AN6 AN4 AN5 K
L TDI TDO ALLPST FB_D3 FB_D1 FB_A1 FB_A0 URXD1 AN2 VRH VDDA AN7 L
MVSS JTAG_
EN TCLK FB_RW FB_CS0 FB_A2 ICOC3 URTS1 AN0 AN1 VRL VSSA M
123456789101112
Figure 4. Pinout Top View (144 MAPBGA)
Family Configurations
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 18
Table 3 shows the pin functions by primary and alternate purpose, and illustrates which packages contain each pin.
Table 3. Pin Functions by Primary and Alternate Purpose
Pin Group Primary
Function
Secondary
Function
(Alt 1)
Tertiary
Function
(Alt 2)
Quaternary
Function
(GPIO)
Slew
Rate
Drive
Strength/Co
ntrol1
Pull-up/
Pull-down2
Pin on
144 MAPBGA
Pin on
144 LQFP
Pin on
100 LQFP
ADC AN[7:0] PAN[7:0] Low Low L12, K10, K12,
K11, K9, L9,
M10, M9
74–77; 69,
68, 67 ,66
51–54, 46,
45, 44, 43
VDDA N/A N/A L11 73 50
VSSA N/A N/A M12 70 47
VRH N/A N/A L10 72 49
VRL N/A N/A M11 71 48
Clock
Generation
EXTAL N/A N/A C12 106 73
XTAL N/A N/A D12 105 72
VDDPLL N/A N/A C11 107 74
VSSPLL N/A N/A D11 104 71
RTC RTC_EXTAL N/A N/A D1 13 7
RTC_XTAL N/A N/A E1 14 8
Debug
Data
ALLPST Low High L3 42 30
DDATA[3:0] PDD[7:4] Low High G9, H10, F11,
F10
86, 85, 84,
83
PST[3:0] PDD[3:0] Low High F9, G10, G11,
G12
87–90
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale19
Family Configurations
FEC FEC_COL PTI0 PSRRH[0] PDSRH[0] B11 109 76
FEC_CRS PTI1 PSRRH[1] PDSRH[1] B12 108 75
FEC_RXCLK PTI2 PSRRH[2] PDSRH[2] B8 120 87
FEC_RXD[3:0] PTI[6:3] PSRRH[6:3] PDSRH[6:3] D7, C7, B7, A8 127, 126,
123, 122
94, 93, 90,
89
FEC_RXDV PTI7 PSRRH[7] PDSRH[7] C8 121 88
FEC_RXER PTJ0 PSRRH[8] PDSRH[8] A9 119 86
FEC_TXCLK PTJ1 PSRRH[9] PDSRH[9] B9 117 84
FEC_TXD[3:0] PTJ[5:2] PSRRH[13:10] PDSRH[13:1
0]
A11, B10, C9,
D9
110–113 77, 78, 79,
80
FEC FEC_TXEN PTJ6 PSRRH[14] PDSRH[14] A10 116 83
FEC_TXER PTJ7 PSRRH[15] PDSRH[15] D8 118 85
I2C03I2C_SCL0 UTXD2 PAS0 PSRR[0] PDSR[0] Pull-Up4H1 28 22
I2C_SDA0 URXD2 PAS1 PSRR[0] PDSR[0] Pull-Up4H2 29 23
Interrupts IRQ7 PNQ7 Low Low Pull-Up4E12 96 63
IRQ5 FEC_MDC PNQ5 Low Low Pull-Up4A7 128 95
IRQ3 FEC_MDIO PNQ3 Low Low Pull-Up4A6 129 96
IRQ1 USB_ALT
CLK
PNQ1 Low High Pull-Up4E9 103 70
JTAG/BDM JTAG_EN N/A N/A Pull-Down M2 44 32
TCLK/
PSTCLK/
CLKOUT
—FB_CLK Low Low Pull-Up
5M3 43 31
TDI/DSI N/A N/A Pull-Up5L1 40 28
TDO/DSO Low Low L2 41 29
TMS/BKPT N/A N/A Pull-Up5K1 38 26
TRST/DSCLK N/A N/A Pull-Up5K2 39 27
Table 3. Pin Functions by Primary and Alternate Purpose (continued)
Pin Group Primary
Function
Secondary
Function
(Alt 1)
Tertiary
Function
(Alt 2)
Quaternary
Function
(GPIO)
Slew
Rate
Drive
Strength/Co
ntrol1
Pull-up/
Pull-down2
Pin on
144 MAPBGA
Pin on
144 LQFP
Pin on
100 LQFP
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale20
Family Configurations
Mode
Selection
RCON/EZPCS N/A N/A Pull-Up E4 10 4
CLKMOD[1:0] N/A N/A Pull-Down D4, D5 144, 143 100, 99
QSPI QSPI_CS3 SYNCA USB_DP_
PDOWN
PQS6 PSRR[7] PDSR[7] G4 22 16
QSPI_CS2 SYNCB USB_DM
_
PDOWN
PQS5 PSRR[6] PDSR[6] G3 23 17
QSPI_CS0 I2C_SDA0 UCTS1 PQS3 PSRR[4] PDSR[4] Pull-Up6H4 27 21
QSPI_CLK/
EZPCK
I2C_SCL0 URTS1 PQS2 PSRR[3] PDSR[3] Pull-Up6H3 26 20
QSPI QSPI_DIN/
EZPD
I2C_SDA1 URXD1 PQS1 PSRR[2] PDSR[2] Pull-Up6G2 24 18
QSPI_DOUT/E
ZPQ
I2C_SCL1 UTXD1 PQS0 PSRR[1] PDSR[1] Pull-Up6G1 25 19
Reset7RSTI N/A N/A Pull-Up7A3 141 97
RSTO Low High A2 142 98
Test TEST N/A N/A Pull-Down B1 9 3
Timer 3,
16-bit
GPT3 PWM7 PTA3 PSRR[23] PDSR[23] Pull-Up8M7 58 35
Timer 2,
16-bit
GPT2 PWM5 PTA2 PSRR[22] PDSR[22] Pull-Up8J10 95 62
Timer 1,
16-bit
GPT1 PWM3 PTA1 PSRR[21] PDSR[21] Pull-Up8J11 94 61
Timer 0,
16-bit
GPT0 PWM1 PTA0 PSRR[20] PDSR[20] Pull-Up8F12 93 60
Timer 3,
32-bit
DTIN3 DTOUT3 PWM6 PTC3 PSRR[19] PDSR[19] F4 19 13
Timer 2,
32-bit
DTIN2 DTOUT2 PWM4 PTC2 PSRR[18] PDSR[18] J8 65 42
Table 3. Pin Functions by Primary and Alternate Purpose (continued)
Pin Group Primary
Function
Secondary
Function
(Alt 1)
Tertiary
Function
(Alt 2)
Quaternary
Function
(GPIO)
Slew
Rate
Drive
Strength/Co
ntrol1
Pull-up/
Pull-down2
Pin on
144 MAPBGA
Pin on
144 LQFP
Pin on
100 LQFP
Family Configurations
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 21
Timer 1,
32-bit
DTIN1 DTOUT1 PWM2 PTC1 PSRR[17] PDSR[17] C1 12 6
Timer 0,
32-bit
DTIN0 DTOUT0 PWM0 PTC0 PSRR[16] PDSR[16] D2 11 5
UART 0 UCTS0 USB_VBU
SE
PUA3 PSRR[11] PDSR[11] E2 15 9
URTS0 USB_VBU
SD
PUA2 PSRR[10] PDSR[10] F3 18 12
URXD0 PUA1 PSRR[9] PDSR[9] F2 17 11
UTXD0 PUA0 PSRR[8] PDSR[8] F1 16 10
UART 1 UCTS1 SYNCA URXD2 PUB3 PSRR[15] PDSR[15] K7 61 38
URTS1 SYNCB UTXD2 PUB2 PSRR[14] PDSR[14] M8 64 41
URXD1 I2C_SDA1 PUB1 PSRR[13] PDSR[13] Pull-Up6L8 63 40
UTXD1 I2C_SCL1 PUB0 PSRR[12] PDSR[12] Pull-Up6K8 62 39
UART 2 UCTS2 I2C_SCL1 USB_
VBUSCH
G
PUC3 PSRR[27] PDSR[27] Pull-Up6E11 97 64
URTS2 I2C_SDA1 USB_
VBUSDIS
PUC2 PSRR[26] PDSR[26] Pull-Up6E10 98 65
URXD2 CANRX PUC1 PSRR[25] PDSR[25] C10 102 69
UTXD2 CANTX PUC0 PSRR[24] PDSR[24] D10 101 68
USB OTG USB_DM N/A N/A H11 80 57
USB_DP N/A N/A H12 81 58
USB_VDD N/A N/A J9 79 56
USB_VSS N/A N/A H9 82 59
Table 3. Pin Functions by Primary and Alternate Purpose (continued)
Pin Group Primary
Function
Secondary
Function
(Alt 1)
Tertiary
Function
(Alt 2)
Quaternary
Function
(GPIO)
Slew
Rate
Drive
Strength/Co
ntrol1
Pull-up/
Pull-down2
Pin on
144 MAPBGA
Pin on
144 LQFP
Pin on
100 LQFP
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale22
Family Configurations
Mini-
FlexBus9
FB_ALE FB_CS1 PAS2 PSRRL[20] PDSRL[20] K3 37
FB_AD[7:0] PTE[7:0] PSRRL[7:0] PDSRL[7:0] J2, J1, K4, K6,
J6, M6, L6, L7
34–36;
53–57
FB_AD[15:8] PTF[7:0] PSRRL[15:8] PDSRL[15:8] C4, B2, C3,
C2, D3, E3, J3,
J4
136, 2–6,
32–33
FB_AD[19:16] PTG[3:0] PSRRL[19:16] PDSRL[19:16
]
B6, C6, D6, C5 130–133
FB_CS0 PTG5 PSRRL[21] PDSRL[21] M5 52
FB_R/W PTG7 PSRRL[31] PDSRL[31] M4 45
FB_OE PTG6 PSRRL[30] PDSRL[30] B5 137
FB_D7 CANRX PTH5 PSRRL[29] PDSRL[29] A5 138
FB_D6 CANTX PTH4 PSRRL[28] PDSRL[28] A4 139
FB_D5 I2C_SCL1 PTH3 PSRRL[27] PDSRL[27] Pull-Up6B4 140
FB_D4 I2C_SDA1 PTH2 PSRRL[26] PDSRL[26] Pull-Up6B3 1
FB_D3 USB_
VBUSD
PTH1 PSRRL[25] PDSRL[25] L4 46
FB_D2 USB_
VBUSE
PTH0 PSRRL[24] PDSRL[24] K5 47
FB_D1 SYNCA PTH7 PSRRL[23] PDSRL[23] L5 50
FB_D0 SYNCB PTH6 PSRRL[22] PDSRL[22] J5 51
Standby
Voltage
VSTBY N/A N/A J12 78 55
VDD10 VDD N/A N/A E5–E8; F5;
G5; H5–7; J7
7; 20; 30;
48; 59; 92;
100; 115;
125; 135
1; 14; 24;
33; 36; 67;
82; 92
Table 3. Pin Functions by Primary and Alternate Purpose (continued)
Pin Group Primary
Function
Secondary
Function
(Alt 1)
Tertiary
Function
(Alt 2)
Quaternary
Function
(GPIO)
Slew
Rate
Drive
Strength/Co
ntrol1
Pull-up/
Pull-down2
Pin on
144 MAPBGA
Pin on
144 LQFP
Pin on
100 LQFP
Family Configurations
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 23
VSS VSS N/A N/A A1; A12; F6–8;
G6–8; H8; M1
8; 21; 31;
49; 60; 91;
99; 114;
124; 134
2; 15; 25;
34; 37; 66;
81; 91
1The PDSR and PSSR registers are part of the GPIO module. All programmable signals default to 2mA drive in normal (single-chip) mode.
2All signals have a pull-up in GPIO mode.
3I2C1 is multiplexed with specific pins of the QSPI, UART1, UART2, and Mini-FlexBus pin groups.
4For primary and GPIO functions only.
5Only when JTAG mode is enabled.
6For secondary and GPIO functions only.
7RSTI has an internal pull-up resistor; however, the use of an external resistor is strongly recommended.
8For GPIO functions, the Primary Function has pull-up control within the GPT module.
9Available on 144-pin packages only.
10 This list for power and ground does not include those dedicated power/ground pins included elsewhere, such as in the ADC, USB, and PLL.
Table 3. Pin Functions by Primary and Alternate Purpose (continued)
Pin Group Primary
Function
Secondary
Function
(Alt 1)
Tertiary
Function
(Alt 2)
Quaternary
Function
(GPIO)
Slew
Rate
Drive
Strength/Co
ntrol1
Pull-up/
Pull-down2
Pin on
144 MAPBGA
Pin on
144 LQFP
Pin on
100 LQFP
Electrical Characteristics
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 24
2 Electrical Characteristics
This section contains electrical specification tables and reference timing diagrams for the microcontroller unit, including
detailed information on power considerations, DC/AC electrical characteristics, and AC timing specifications.
NOTE
The parameters specified in this data sheet supersede any values found in the module
specifications.
2.1 Maximum Ratings
Table 4. Absolute Maximum Ratings1, 2
1Functional operating conditions are given in DC Electrical Specifications. Absolute Maximum Ratings
are stress ratings only, and functional operation at the maxima is not guaranteed. Stress beyond
those listed may affect device reliability or cause permanent damage to the device.
2This device contains circuitry protecting against damage due to high static voltage or electrical fields;
however, it is advised that normal precautions be taken to avoid application of any voltages higher
than maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if
unused inputs are tied to an appropriate logic voltage level (VSS or VDD).
Rating Symbol Value Unit
Supply voltage VDD –0.3 to 4.0 V
Clock synthesizer supply voltage VDDPLL –0.3 to 4.0 V
RAM standby supply voltage VSTBY +1.8 to 3.5 V
USB standby supply voltage VDDUSB –0.3 to 4.0 V
Digital input voltage 3
3Input must be current limited to the IDD value specified. To determine the value of the required
current-limiting resistor, calculate resistance values for positive and negative clamp voltages, then
use the larger of the two values.
VIN –0.3 to 4.0 V
EXTAL pin voltage VEXTAL 0 to 3.3 V
XTAL pin voltage VXTAL 0 to 3.3 V
Instantaneous maximum current
Single pin limit (applies to all pins)4, 5
4All functional non-supply pins are internally clamped to VSS and VDD.
5The power supply must maintain regulation within operating VDD range during instantaneous and
operating maximum current conditions. If positive injection current (Vin > VDD) is greater than IDD, the
injection current may flow out of VDD and could result in the external power supply going out of
regulation. Ensure that the external VDD load shunts current greater than maximum injection current.
This is the greatest risk when the MCU is not consuming power (e.g., no clock).
IDD 25 mA
Operating temperature range (packaged) TA
(TL - TH)
–40 to 85 or
0 to 706
6Depending on the packaging; see orderable part number summary (Ta b l e 2 )
C
Storage temperature range Tstg –65 to 150 C
MCF52259 ColdFire Microcontroller, Rev. 5
Electrical Characteristics
Freescale25
2.2 Current Consumption
Table 5. Typical Active Current Consumption Specifications
Characteristic Symbol
Typical1
Active
(SRAM)
1Tested at room temperature with CPU polling a status register. All clocks were off except the UART and CFM (when
running from flash memory).
Typical1
Active
(Flash)
Peak2
(Flash)
2Peak current measured with all modules active, CPU polling a status register, and default drive strength with matching
load.
Unit
PLL @ 8 MHz IDD 22 30 36 mA
PLL @ 16 MHz 31 45 60
PLL @ 64 MHz 84 100 155
PLL @ 80 MHz 102 118 185
RAM standby supply current
Normal operation: VDD > VSTBY - 0.3 V
Standby operation: VDD < VSS + 0.5 V
ISTBY
5
20
A
A
Analog supply current
Normal operation IDDA 2 3
3Tested using Auto Power Down (APD), which powers down the ADC between conversions; ADC running at 4 MHz in
Once Parallel mode with a sample rate of 3 kHz.
15 mA
USB supply current IDDUSB —2mA
PLL supply current IDDPLL —6
4
4Tested with the PLL MFD set to 7 (max value). Setting the MFD to a lower value results in lower current consumption.
mA
Table 6. Current Consumption in Low-Power Mode, Code From Flash Memory1,2,3
1All values are measured with a 3.30 V power supply. Tests performed at room temperature.
2Refer to the Power Management chapter in the MCF52259 Reference Manual for more information on low-power
modes.
3CLKOUT, PST/DDATA signals, and all peripheral clocks except UART0 and CFM off before entering low-power
mode. CLKOUT is disabled.
Mode 8 MHz (Typ) 16 MHz (Typ) 64 MHz (Typ) 80 MHz (Typ) Unit Symbol
Stop mode 3 (Stop 11)4
4See the description of the Low-Power Control Register (LPCR) in the MCF52259 Reference Manual for more
information on stop modes 0–3.
0.150
mA IDD
Stop mode 2 (Stop 10)47.0
Stop mode 1 (Stop 01)4,5
5Results are identical to STOP 00 for typical values because they only differ by CLKOUT power consumption.
CLKOUT is already disabled in this instance prior to entering low-power mode.
9 101517
Stop mode 0 (Stop 00)59 101517
Wait / Doze 21 32 56 65
Run 23367081
Electrical Characteristics
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 26
2.3 Thermal Characteristics
Table 8 lists thermal resistance values.
Table 7. Current Consumption in Low-Power Mode, Code From SRAM1,2,3
1All values are measured with a 3.3 V power supply. Tests performed at room temperature.
2Refer to the Power Management chapter in the MCF52259 Reference Manual for more information on low-power
modes.
3CLKOUT, PST/DDATA signals, and all peripheral clocks except UART0 off before entering low-power mode.
CLKOUT is disabled. Code executed from SRAM with flash memory shut off by writing 0x0 to the FLASHBAR
register.
Mode 8 MHz (Typ) 16 MHz (Typ) 64 MHz (Typ) 80 MHz (Typ) Unit Symbol
Stop mode 3 (Stop 11)4
4See the description of the Low-Power Control Register (LPCR) in the MCF52259 Reference Manual for more
information on stop modes 0–3.
0.090
mA IDD
Stop mode 2 (Stop 10)47
Stop mode 1 (Stop 01)4,5
5Results are identical to STOP 00 for typical values because they only differ by CLKOUT power consumption.
CLKOUT is already disabled in this instance prior to entering low-power mode.
9 101517
Stop mode 0 (Stop 00)59 101517
Wait / Doze 13 18 42 50
Run 16215565
Table 8. Thermal Characteristics
Characteristic Symbol Value Unit
144 MAPBGA Junction to ambient, natural convection Single layer board (1s) JA 531,2 C / W
Junction to ambient, natural convection Four layer board (2s2p) JA 301,3 C / W
Junction to ambient, (@200 ft/min) Single layer board (1s) JMA 431,3 C / W
Junction to ambient, (@200 ft/min) Four layer board (2s2p) JMA 261,3 C / W
Junction to board JB 164C / W
Junction to case JC 95C / W
Junction to top of package Natural convection jt 26C / W
Maximum operating junction temperature Tj105 oC
144 LQFP Junction to ambient, natural convection Single layer board (1s) JA 447,8 C / W
Junction to ambient, natural convection Four layer board (2s2p) JA 351,9 C / W
Junction to ambient, (@200 ft/min) Single layer board (1s) JMA 351,3 C / W
Junction to ambient, (@200 ft/min) Four layer board (2s2p) JMA 291,3 C / W
Junction to board JB 2310 C / W
Junction to case JC 711 C / W
Junction to top of package Natural convection jt 212 C / W
Maximum operating junction temperature Tj105 oC
MCF52259 ColdFire Microcontroller, Rev. 5
Electrical Characteristics
Freescale27
100 LQFP Junction to ambient, natural convection Single layer board (1s) JA 5313,14 C / W
Junction to ambient, natural convection Four layer board (2s2p) JA 391,15 C / W
Junction to ambient, (@200 ft/min) Single layer board (1s) JMA 421,3 C / W
Junction to ambient, (@200 ft/min) Four layer board (2s2p) JMA 331,3 C / W
Junction to board JB 2516 C / W
Junction to case JC 917 C / W
Junction to top of package Natural convection jt 218 C / W
Maximum operating junction temperature Tj105 oC
1JA and jt parameters are simulated in conformance with EIA/JESD Standard 51-2 for natural convection. Freescale
recommends the use of JA and power dissipation specifications in the system design to prevent device junction
temperatures from exceeding the rated specification. System designers should be aware that device junction temperatures
can be significantly influenced by board layout and surrounding devices. Conformance to the device junction temperature
specification can be verified by physical measurement in the customer’s system using the jt parameter, the device power
dissipation, and the method described in EIA/JESD Standard 51-2.
2Per JEDEC JESD51-2 with the single-layer board (JESD51-3) horizontal.
3Per JEDEC JESD51-6 with the board JESD51-7) horizontal.
4Thermal resistance between the die and the printed circuit board in conformance with JEDEC JESD51-8. Board
temperature is measured on the top surface of the board near the package.
5Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883
Method 1012.1).
6Thermal characterization parameter indicating the temperature difference between package top and the junction
temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written
in conformance with Psi-JT.
7JA and jt parameters are simulated in conformance with EIA/JESD Standard 51-2 for natural convection. Freescale
recommends the use of JA and power dissipation specifications in the system design to prevent device junction
temperatures from exceeding the rated specification. System designers should be aware that device junction temperatures
can be significantly influenced by board layout and surrounding devices. Conformance to the device junction temperature
specification can be verified by physical measurement in the customer’s system using the jt parameter, the device power
dissipation, and the method described in EIA/JESD Standard 51-2.
8Per JEDEC JESD51-2 with the single-layer board (JESD51-3) horizontal.
9Per JEDEC JESD51-6 with the board JESD51-7) horizontal.
10 Thermal resistance between the die and the printed circuit board in conformance with JEDEC JESD51-8. Board
temperature is measured on the top surface of the board near the package.
11 Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883
Method 1012.1).
12 Thermal characterization parameter indicating the temperature difference between package top and the junction
temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written
in conformance with Psi-JT.
13 JA and jt parameters are simulated in conformance with EIA/JESD Standard 51-2 for natural convection. Freescale
recommends the use of JA and power dissipation specifications in the system design to prevent device junction
temperatures from exceeding the rated specification. System designers should be aware that device junction temperatures
can be significantly influenced by board layout and surrounding devices. Conformance to the device junction temperature
specification can be verified by physical measurement in the customer’s system using the jt parameter, the device power
dissipation, and the method described in EIA/JESD Standard 51-2.
14 Per JEDEC JESD51-2 with the single-layer board (JESD51-3) horizontal.
15 Per JEDEC JESD51-6 with the board JESD51-7) horizontal.
Table 8. Thermal Characteristics (continued)
Characteristic Symbol Value Unit
Electrical Characteristics
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 28
2.4 Flash Memory Characteristics
The flash memory characteristics are shown in Table 9 and Table 10.
16 Thermal resistance between the die and the printed circuit board in conformance with JEDEC JESD51-8. Board
temperature is measured on the top surface of the board near the package.
17 Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883
Method 1012.1).
18 Thermal characterization parameter indicating the temperature difference between package top and the junction
temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written
in conformance with Psi-JT.
The average chip-junction temperature (TJ) in C can be obtained from:
(1)
Where:
TA= ambient temperature, C
JA = package thermal resistance, junction-to-ambient, C/W
PD= PINT PI/O
PINT = chip internal power, IDD VDD, W
PI/O = power dissipation on input and output pins — user determined, W
For most applications PI/O PINT and can be ignored. An approximate relationship between PD and TJ (if PI/O is neglected) is:
(2)
Solving equations 1 and 2 for K gives:
K = PD (TA + 273 C) + JMA PD 2 (3)
where K is a constant pertaining to the particular part. K can be determined from equation (3) by measuring PD (at equilibrium)
for a known TA. Using this value of K, the values of PD and TJ can be obtained by solving equations (1) and (2) iteratively for
any value of TA.
Table 9. SGFM Flash Program and Erase Characteristics
(VDD = 3.0 to 3.6 V)
Parameter Symbol Min Typ Max Unit
System clock (read only) fsys(R) 0—66.67 or 801
1Depending on packaging; see the orderable part number summary (Ta b l e 2 ).
MHz
System clock (program/erase)2
2Refer to the flash memory section for more information (Section 2.4, “Flash Memory Characteristics”)
fsys(P/E) 0.15 66.67 or 801MHz
Table 10. SGFM Flash Module Life Characteristics
(VDD = 3.0 to 3.6 V)
Parameter Symbol Value Unit
Maximum number of guaranteed program/erase cycles1 before failure
1A program/erase cycle is defined as switching the bits from 1 0 1.
P/E 10,0002Cycles
Data retention at average operating temperature of 85C Retention 10 Years
TJTAPDJMA
+=
PDKT
J273C+=
MCF52259 ColdFire Microcontroller, Rev. 5
Electrical Characteristics
Freescale29
2.5 EzPort Electrical Specifications
2.6 ESD Protection
2Reprogramming of a flash memory array block prior to erase is not required.
Table 11. EzPort Electrical Specifications
Name Characteristic Min Max Unit
EP1 EPCK frequency of operation (all commands except READ) fsys / 2 MHz
EP1a EPCK frequency of operation (READ command) fsys / 8 MHz
EP2 EPCS_b negation to next EPCS_b assertion 2 × Tcyc —ns
EP3 EPCS_B input valid to EPCK high (setup) 5 ns
EP4 EPCK high to EPCS_B input invalid (hold) 5 ns
EP5 EPD input valid to EPCK high (setup) 2 ns
EP6 EPCK high to EPD input invalid (hold) 5 ns
EP7 EPCK low to EPQ output valid (out setup) 12 ns
EP8 EPCK low to EPQ output invalid (out hold) 0 ns
EP9 EPCS_B negation to EPQ tri-state 12 ns
Table 12. ESD Protection Characteristics1, 2
1All ESD testing is in conformity with CDF-AEC-Q100 Stress Test Qualification for
Automotive Grade Integrated Circuits.
2A device is defined as a failure if after exposure to ESD pulses the device no longer
meets the device specification requirements. Complete DC parametric and functional
testing is performed per applicable device specification at room temperature followed by
hot temperature, unless specified otherwise in the device specification.
Characteristics Symbol Value Units
ESD target for Human Body Model HBM 2000 V
ESD target for Machine Model MM 200 V
HBM circuit description Rseries 1500
C 100 pF
MM circuit description Rseries 0
C 200 pF
Number of pulses per pin (HBM)
Positive pulses
Negative pulses
1
1
Number of pulses per pin (MM)
Positive pulses
Negative pulses
3
3
Interval of pulses 1 sec
Electrical Characteristics
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 30
2.7 DC Electrical Specifications
Table 13. DC Electrical Specifications 1
1Refer to Ta bl e 1 4 for additional PLL specifications.
Characteristic Symbol Min Max Unit
Supply voltage VDD 3.0 3.6 V
Standby voltage VSTBY 1.8 3.5 V
Input high voltage VIH 0.7 VDD 4.0 V
Input low voltage VIL VSS – 0.3 0.35 VDD V
Input hysteresis2
2Only for pins: IRQ1, IRQ3. IRQ5, IRQ7, RSTIN_B, TEST, RCON_B, PCS0, SCK, I2C_SDA, I2C_SCL, TCLK, TRST_B
VHYS 0.06 VDD —mV
Low-voltage detect trip voltage (VDD falling) VLVD 2.15 2.3 V
Low-voltage detect hysteresis (VDD rising) VLVD H YS 60 120 mV
Input leakage current
Vin = VDD or VSS, digital pins
Iin –1.0 1.0 A
Output high voltage (all input/output and all output pins)
IOH = –2.0 mA
VOH VDD – 0.5 V
Output low voltage (all input/output and all output pins)
IOL = 2.0 mA
VOL —0.5V
Output high voltage (high drive)
IOH = -5 mA
VOH VDD – 0.5 V
Output low voltage (high drive)
IOL = 5 mA
VOL —0.5V
Output high voltage (low drive)
IOH = -2 mA
VOH VDD - 0.5 V
Output low voltage (low drive)
IOL = 2 mA
VOL —0.5V
Weak internal pull Up device current, tested at VIL Max.3
3Refer to Ta bl e 3 for pins having internal pull-up devices.
IAPU –10 –130 A
Input Capacitance 4
All input-only pins
All input/output (three-state) pins
4This parameter is characterized before qualification rather than 100% tested.
Cin
7
7
pF
MCF52259 ColdFire Microcontroller, Rev. 5
Electrical Characteristics
Freescale31
2.8 Clock Source Electrical Specifications
Table 14. Oscillator and PLL Specifications
(VDD and VDDPLL = 3.0 to 3.6 V, VSS = VSSPLL = 0 V)
Characteristic Symbol Min Max Unit
Clock Source Frequency Range of EXTAL Frequency Range
Crystal
External1
1In external clock mode, it is possible to run the chip directly from an external clock source without enabling the PLL.
fcrystal
fext
12
0
25.02
66.67 or 80
2This value has been updated.
MHz
PLL reference frequency range fref_pll 210.0MHz
System frequency 3
External clock mode
On-chip PLL frequency
3All internal registers retain data at 0 Hz.
fsys
0
fref / 32
66.67 or 804
66.67 or 804
4Depending on packaging; see the orderable part number summary (Ta b l e 2 ).
MHz
Loss of reference frequency 5, 7
5Loss of Reference Frequency is the reference frequency detected internally, which transitions the PLL into self clocked mode.
fLOR 100 1000 kHz
Self clocked mode frequency 6
6Self clocked mode frequency is the frequency at which the PLL operates when the reference frequency falls below fLOR with
default MFD/RFD settings.
fSCM 15MHz
Crystal start-up time 7, 8
7This parameter is characterized before qualification rather than 100% tested.
8Proper PC board layout procedures must be followed to achieve specifications.
tcst —0.1ms
EXTAL input high voltage
External reference
VIHEXT
2.0 3.02
V
EXTAL input low voltage
External reference
VILEXT
VSS 0.8
V
PLL lock time4,9
9This specification applies to the period required for the PLL to relock after changing the MFD frequency control bits in the
synthesizer control register (SYNCR).
tlpll —500s
Duty cycle of reference 4 tdc 40 60 % fref
Frequency un-LOCK range fUL –1.5 1.5 % fref
Frequency LOCK range fLCK –0.75 0.75 % fref
CLKOUT period jitter 4, 5, 10 ,11, measured at fSYS Max
Peak-to-peak (clock edge to clock edge)
Long term (averaged over 2 ms interval)
10 Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum fsys.
Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise
injected into the PLL circuitry via VDDPLL and VSSPLL and variation in crystal oscillator frequency increase the Cjitter percentage
for a given interval.
11 Based on slow system clock of 40 MHz measured at fsys max.
Cjitter
10
.01
% fsys
On-chip oscillator frequency foco 7.84 8.16 MHz
Electrical Characteristics
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 32
2.9 USB Operation
2.10 Mini-FlexBus External Interface Specifications
A multi-function external bus interface called Mini-FlexBus is provided with basic functionality to interface to slave-only
devices up to a maximum bus frequency of 80 MHz. It can be directly connected to asynchronous or synchronous devices such
as external boot ROMs, flash memories, gate-array logic, or other simple target (slave) devices with little or no additional
circuitry. For asynchronous devices a simple chip-select based interface can be used.
All processor bus timings are synchronous; that is, input setup/hold and output delay are given in respect to the rising edge of
a reference clock, MB_CLK. The MB_CLK frequency is half the internal system bus frequency.
The following timing numbers indicate when data is latched or driven onto the external bus, relative to the Mini-FlexBus output
clock (MB_CLK). All other timing relationships can be derived from these values.
Table 15. USB Operation Specifications
Characteristic Symbol Value Unit
Minimum core speed for USB operation fsys_USB_min 16 MHz
Table 16. Mini-FlexBus AC Timing Specifications
Num Characteristic Min Max Unit Notes
Frequency of Operation 80 MHz
MB1 Clock Period 12.5 ns
MB2 Output Valid 8 ns 1
1Specification is valid for all MB_A[19:0], MB_D[7:0], MB_CS[1:0], MB_OE, MB_R/W, and MB_ALE.
MB3 Output Hold 2 ns 1
MB4 Input Setup 6 ns 2
2Specification is valid for all MB_D[7:0].
MB5 Input Hold 0 ns 2
MCF52259 ColdFire Microcontroller, Rev. 5
Electrical Characteristics
Freescale33
Figure 5. Mini-FlexBus Read Timing
Figure 6. Mini-FlexBus Write Timing
2.11 Fast Ethernet Timing Specifications
The following timing specs are defined at the chip I/O pin and must be translated appropriately to arrive at timing
specs/constraints for the physical interface.
MB_CLK
MB_A[19:X]
MB_D[7:0] /
MB_R/W
MB_ALE
MB_CSn
MB_OE
MB1
A[19:X]
MB2
MB3
MB4
MB5
D[Y:0]ADDRESS
MB_A[15:0]
MB2
MB3
MB3
MB2
Electrical Characteristics
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 34
2.11.1 Receive Signal Timing Specifications
The following timing specs meet the requirements for MII and 7-Wire style interfaces for a range of transceiver devices.
Figure 7. MII Receive Signal Timing Diagram
2.11.2 Transmit Signal Timing Specifications
Figure 8. MII Transmit Signal Timing Diagram
Table 17. Receive Signal Timing
Num Characteristic
MII Mode
Unit
Min Max
RXCLK frequency 25 MHz
E1 RXD[n:0], RXDV, RXER to RXCLK setup1
1In MII mode, n = 3
5— ns
E2 RXCLK to RXD[n:0], RXDV, RXER hold15— ns
E3 RXCLK pulse width high 35% 65% RXCLK period
E4 RXCLK pulse width low 35% 65% RXCLK period
Table 18. Transmit Signal Timing
Num Characteristic
MII Mode
Unit
Min Max
TXCLK frequency 25 MHz
E5 TXCLK to TXD[n:0], TXEN, TXER invalid1
1In MII mode, n = 3
5— ns
E6 TXCLK to TXD[n:0], TXEN, TXER valid1—25 ns
E7 TXCLK pulse width high 35% 65% tTXCLK
E8 TXCLK pulse width low 35% 65% tTXCLK
Valid Data
RXCLK (Input)
RXD[n:0]
RXDV,
RXER
E3
E4
E1 E2
Valid Data
TXCLK (Input)
TXD[n:0]
TXEN,
TXER
E7
E8
E5
E6
MCF52259 ColdFire Microcontroller, Rev. 5
Electrical Characteristics
Freescale35
2.11.3 Asynchronous Input Signal Timing Specifications
Figure 9. MII Async Inputs Timing Diagram
2.11.4 MII Serial Management Timing Specifications
Figure 10. MII Serial Management Channel TIming Diagram
2.12 General Purpose I/O Timing
GPIO can be configured for certain pins of the QSPI, DDR Control, timer, UART, Interrupt and USB interfaces. When in GPIO
mode, the timing specification for these pins is given in Table 21 and Figure 11.
The GPIO timing is met under the following load test conditions:
•50pF/50 for high drive
Table 19. MII Transmit Signal Timing
Num Characteristic Min Max Unit
E9 CRS, COL minimum pulse width 1.5 TXCLK period
Table 20. MII Serial Management Channel Signal Timing
Num Characteristic Symbol Min Max Unit
E10 MDC cycle time tMDC 400 ns
E11 MDC pulse width 40 60 % tMDC
E12 MDC to MDIO output valid 375 ns
E13 MDC to MDIO output invalid 25 ns
E14 MDIO input to MDC setup 10 ns
E15 MDIO input to MDC hold 0 ns
CRS, COL
E9
MDC (Output)
E11
MDIO (Output)
MDIO (Input)
E11
E12 E13
Valid Data
E14 E15
Valid Data
E10
Electrical Characteristics
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 36
•25pF/25 for low drive
Figure 11. GPIO Timing
2.13 Reset Timing
Figure 12. RSTI and Configuration Override Timing
Table 21. GPIO Timing
NUM Characteristic Symbol Min Max Unit
G1 CLKOUT High to GPIO Output Valid tCHPOV —10ns
G2 CLKOUT High to GPIO Output Invalid tCHPOI 1.5 ns
G3 GPIO Input Valid to CLKOUT High tPVCH 9—ns
G4 CLKOUT High to GPIO Input Invalid tCHPI 1.5 ns
Table 22. Reset and Configuration Override Timing
(VDD = 3.0 to 3.6 V, VSS = 0 V, TA = TL to TH)1
1All AC timing is shown with respect to 50% VDD levels unless otherwise noted.
NUM Characteristic Symbol Min Max Unit
R1 RSTI input valid to CLKOUT High tRVCH 9—ns
R2 CLKOUT High to RSTI Input invalid tCHRI 1.5 ns
R3 RSTI input valid time 2
2During low power STOP, the synchronizers for the RSTI input are bypassed and RSTI is asserted asynchronously to the
system. Thus, RSTI must be held a minimum of 100 ns.
tRIVT 5—t
CYC
R4 CLKOUT High to RSTO Valid tCHROV —10ns
G1
CLKOUT
GPIO Outputs
G2
G3 G4
GPIO Inputs
1R1 R2
CLKOUT
RSTI
RSTO
R3
R4 R4
MCF52259 ColdFire Microcontroller, Rev. 5
Electrical Characteristics
Freescale37
2.14 I2C Input/Output Timing Specifications
Table 23 lists specifications for the I2C input timing parameters shown in Figure 13.
Table 24 lists specifications for the I2C output timing parameters shown in Figure 13.
Table 23. I2C Input Timing Specifications between I2C_SCL and I2C_SDA
Num Characteristic Min Max Units
I1 Start condition hold time 2 tCYC —ns
I2 Clock low period 8 tCYC —ns
I3 SCL/SDA rise time (VIL = 0.5 V to VIH = 2.4 V) 1 ms
I4 Data hold time 0 ns
I5 SCL/SDA fall time (VIH = 2.4 V to VIL = 0.5 V) 1 ms
I6 Clock high time 4 tCYC —ns
I7 Data setup time 0 ns
I8 Start condition setup time (for repeated start condition only) 2 tCYC —ns
I9 Stop condition setup time 2 tCYC —ns
Table 24. I2C Output Timing Specifications between I2C_SCL and I2C_SDA
Num Characteristic Min Max Units
I11
1Output numbers depend on the value programmed into the IFDR; an IFDR programmed with the
maximum frequency (IFDR = 0x20) results in minimum output timings as shown in Tab l e 24. The I2C
interface is designed to scale the actual data transition time to move it to the middle of the SCL low
period. The actual position is affected by the prescale and division values programmed into the IFDR;
however, the numbers given in Ta b l e 2 4 are minimum values.
Start condition hold time 6 tCYC —ns
I21Clock low period 10 tCYC —ns
I32
2Because SCL and SDA are open-collector-type outputs, which the processor can only actively drive
low, the time SCL or SDA take to reach a high level depends on external signal capacitance and pull-up
resistor values.
I2C_SCL/I2C_SDA rise time
(VIL = 0.5 V to VIH = 2.4 V)
——s
I41Data hold time 7 tCYC —ns
I53
3Specified at a nominal 50 pF load.
I2C_SCL/I2C_SDA fall time
(VIH = 2.4 V to VIL = 0.5 V)
—3ns
I61Clock high time 10 tCYC —ns
I71Data setup time 2 tCYC —ns
I81Start condition setup time (for repeated start
condition only)
20 tCYC —ns
I91Stop condition setup time 10 tCYC —ns
Electrical Characteristics
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 38
Figure 13 shows timing for the values in Table 23 and Table 24.
Figure 13. I2C Input/Output Timings
2.15 Analog-to-Digital Converter (ADC) Parameters
Table 25 lists specifications for the analog-to-digital converter.
Table 25. ADC Parameters1
Name Characteristic Min Typical Max Unit
VREFL Low reference voltage VSSA —V
SSA
+ 50 mV
V
VREFH High reference voltage VDDA
- 50 mV
—V
DDA V
VDDA ADC analog supply voltage 3.1 3.3 3.6 V
VADIN Input voltages VREFL —V
REFH V
RES Resolution 12 12 Bits
INL Integral non-linearity (full input signal range)22.5 3LSB
3
INL Integral non-linearity (10% to 90% input signal range)42.5 3LSB
DNL Differential non-linearity 1 < DNL < 1<1LSB
Monotonicity GUARANTEED
fADIC ADC internal clock 0.1 5.0 MHz
RAD Conversion range VREFL —V
REFH V
tADPU ADC power-up time5—613t
AIC cycles6
tREC Recovery from auto standby 0 1 tAIC cycles
tADC Conversion time 6 tAIC cycles
tADS Sample time 1 tAIC cycles
CADI Input capacitance See Figure 14 —pF
XIN Input impedance See Figure 14 —W
IADI Input injection current7, per pin 3 mA
IVREFH VREFH current 0 mA
VOFFSET Offset voltage internal reference 815 mV
EGAIN Gain error (transfer path) .99 1 1.01
VOFFSET Offset voltage external reference 39mV
I2 I6
I1 I4
I7
I8 I9
I5
I3
SCL
SDA
MCF52259 ColdFire Microcontroller, Rev. 5
Electrical Characteristics
Freescale39
2.16 Equivalent Circuit for ADC Inputs
Figure 14 shows the ADC input circuit during sample and hold. S1 and S2 are always open/closed at the same time that S3 is
closed/open. When S1/S2 are closed and S3 is open, one input of the sample and hold circuit moves to (VREFH-VREFL)/2, while
the other charges to the analog input voltage. When the switches are flipped, the charge on C1 and C2 are averaged via S3, with
the result that a single-ended analog input is switched to a differential voltage centered about (VREFH-VREFL)/2. The switches
switch on every cycle of the ADC clock (open one-half ADC clock, closed one-half ADC clock). There are additional
capacitances associated with the analog input pad, routing, etc., but these do not filter into the S/H output voltage, as S1 provides
isolation during the charge-sharing phase. One aspect of this circuit is that there is an on-going input current, which is a function
of the analog input voltage, VREF and the ADC clock frequency.
1. Parasitic capacitance due to package, pin-to-pin and pin-to-package base coupling; 1.8 pF
2. Parasitic capacitance due to the chip bond pad, ESD protection devices and signal routing; 2.04 pF
3. Equivalent resistance for the channel select mux; 100
4. Sampling capacitor at the sample and hold circuit. Capacitor C1 is normally disconnected from the input and is only
connected to it at sampling time; 1.4 pF
5. Equivalent input impedance, when the input is selected =
Figure 14. Equivalent Circuit for A/D Loading
SNR Signal-to-noise ratio 62 to 66 dB
THD Total harmonic distortion 75 dB
SFDR Spurious free dynamic range 67 to 70.3 dB
SINAD Signal-to-noise plus distortion 61 to 63.9 dB
ENOB Effective number of bits 9.1 10.6 Bits
1All measurements are preliminary pending full characterization, and made at VDD = 3.3 V, VREFH = 3.3 V, and VREFL = ground
2INL measured from VIN = VREFL to VIN = VREFH
3LSB = Least Significant Bit
4INL measured from VIN = 0.1VREFH to VIN = 0.9VREFH
5Includes power-up of ADC and VREF
6ADC clock cycles
7Current that can be injected or sourced from an unselected ADC signal input without impacting the performance of the ADC
Table 25. ADC Parameters1 (continued)
Name Characteristic Min Typical Max Unit
12
3
Analog Input 4
S1
S2
S3
C1
C2
S/H
C1 = C2 = 1pF
(VREFH- VREFL)/ 2
125W ESD Resistor
8pF noise damping capacitor
1
(ADC Clock Rate) (1.410-12)
Electrical Characteristics
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 40
2.17 DMA Timers Timing Specifications
Table 26 lists timer module AC timings.
2.18 QSPI Electrical Specifications
Table 27 lists QSPI timings.
The values in Table 27 correspond to Figure 15.
Figure 15. QSPI Timing
2.19 JTAG and Boundary Scan Timing
Table 26. Timer Module AC Timing Specifications
Name Characteristic1
1All timing references to CLKOUT are given to its rising edge.
Min Max Unit
T1 DTIN0 / DTIN1 / DTIN2 / DTIN3 cycle time 3 tCYC —ns
T2 DTIN0 / DTIN1 / DTIN2 / DTIN3 pulse width 1 tCYC —ns
Table 27. QSPI Modules AC Timing Specifications
Name Characteristic Min Max Unit
QS1 QSPI_CS[3:0] to QSPI_CLK 1 510 tCYC
QS2 QSPI_CLK high to QSPI_DOUT valid 10 ns
QS3 QSPI_CLK high to QSPI_DOUT invalid (Output hold) 2 ns
QS4 QSPI_DIN to QSPI_CLK (Input setup) 9 ns
QS5 QSPI_DIN to QSPI_CLK (Input hold) 9 ns
QSPI_CS[3:0]
QSPI_CLK
QSPI_DOUT
QS5
QS1
QSPI_DIN
QS3 QS4
QS2
MCF52259 ColdFire Microcontroller, Rev. 5
Electrical Characteristics
Freescale41
Figure 16. Test Clock Input Timing
Table 28. JTAG and Boundary Scan Timing
Num Characteristics1
1JTAG_EN is expected to be a static signal. Hence, it is not associated with any timing.
Symbol Min Max Unit
J1 TCLK frequency of operation fJCYC DC 1/4 fsys/2
J2 TCLK cycle period tJCYC 4 tCYC —ns
J3 TCLK clock pulse width tJCW 26 ns
J4 TCLK rise and fall times tJCRF 03ns
J5 Boundary scan input data setup time to TCLK rise tBSDST 4—ns
J6 Boundary scan input data hold time after TCLK rise tBSDHT 26 ns
J7 TCLK low to boundary scan output data valid tBSDV 033ns
J8 TCLK low to boundary scan output high Z tBSDZ 033ns
J9 TMS, TDI input data setup time to TCLK rise tTAPBST 4—ns
J10 TMS, TDI Input data hold time after TCLK rise tTAPBHT 10 ns
J11 TCLK low to TDO data valid tTDODV 026ns
J12 TCLK low to TDO high Z tTDODZ 08ns
J13 TRST assert time tTRSTAT 100 ns
J14 TRST setup time (negation) to TCLK high tTRSTST 10 ns
TCLK
VIL
VIH
J3 J3
J4 J4
J2
(input)
Electrical Characteristics
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 42
Figure 17. Boundary Scan (JTAG) Timing
Figure 18. Test Access Port Timing
Figure 19. TRST Timing
Input Data Valid
Output Data Valid
Output Data Valid
TCLK
Data Inputs
Data Outputs
Data Outputs
Data Outputs
VIL VIH
J5 J6
J7
J8
J7
Input Data Valid
Output Data Valid
Output Data Valid
TCLK
TDI
TDO
TDO
TDO
TMS
VIL VIH
J9 J10
J11
J12
J11
TCLK
TRST
14
13
MCF52259 ColdFire Microcontroller, Rev. 5
Electrical Characteristics
Freescale43
2.20 Debug AC Timing Specifications
Table 29 lists specifications for the debug AC timing parameters shown in Figure 21.
Figure 20 shows real-time trace timing for the values in Table 29.
Figure 20. Real-Time Trace AC Timing
Table 29. Debug AC Timing Specification
Num Characteristic
66/80 MHz
Units
Min Max
D1 PST, DDATA to CLKOUT setup 4 ns
D2 CLKOUT to PST, DDATA hold 1.5 ns
D3 DSI-to-DSCLK setup 1 tCYC —ns
D41
1DSCLK and DSI are synchronized internally. D4 is measured from the synchronized DSCLK input relative to
the rising edge of CLKOUT.
DSCLK-to-DSO hold 4 tCYC —ns
D5 DSCLK cycle time 5 tCYC —ns
D6 BKPT input data setup time to CLKOUT rise 4 ns
D7 BKPT input data hold time to CLKOUT rise 1.5 ns
D8 CLKOUT high to BKPT high Z 0.0 10.0 ns
CLKOUT
PST[3:0]
D2D1
DDATA[3:0]
Package Information
MCF52259 ColdFire Microcontroller, Rev. 5
Freescale 44
Figure 21 shows BDM serial port AC timing for the values in Table 29.
Figure 21. BDM Serial Port AC Timing
3 Package Information
The latest package outline drawings are available on the product summary pages on http://www.freescale.com/coldfire.
Table 30 lists the case outline numbers per device. Use these numbers in the web page’s keyword search engine to find the latest
package outline drawings.
Table 30. Package Information
Device Package Type Case Outline Numbers
MCF52252
100 LQFP 98ASS23308WMCF52254
MCF52255
MCF52256 144 LQFP
or
144 MAPBGA
98ASS23177W
98ASH70694A
MCF52258
MCF52259
DSI
DSO
Current Next
CLKOUT
Past Current
DSCLK
D3
D4
D5
MCF52259 ColdFire Microcontroller, Rev. 5
Revision History
Freescale45
4 Revision History
Table 31. Revision History
Revision Description
0 Initial public release.
1 Added package dimensions to package diagrams
Added listing of devices for MCF52259 family
Changed “Four-channel general-purpose timer (GPT) capable of input capture/output compare, pulse
width modulation (PWM), and pulse accumulation” to “Four-channel general-purpose timer (GPT)
capable of input capture/output compare, pulse width modulation (PWM), pulse-code modulation
(PCM), and pulse accumulation”
Updated the figure Pinout Top View (144 MAPBGA)
Removed an extraneous instance of the table Pin Functions by Primary and Alternate Purpose
In the table Pin Functions by Primary and Alternate Purpose, changed a footnote from “This list for
power and ground does not include those dedicated power/ground pins included elsewhere, such as in
the ADC” to “This list for power and ground does not include those dedicated power/ground pins
included elsewhere, such as in the ADC, USB, and PLL
In the table SGFM Flash Program and Erase Characteristics, changed “(VDDF = 2.7 to 3.6 V)“ to
“(VDD = 3.0 to 3.6 V)“
In the table SGFM Flash Module Life Characteristics, changed “(VDDF = 2.7 to 3.6 V)“ to “(VDD = 3.0
to 3.6 V)“
In the table Oscillator and PLL Specifications, changed “VDD and VDDPLL = 2.7 to 3.6 V“ to “VDD and
VDDPLL = 3.0 to 3.6 V“
In the table Reset and Configuration Override Timing, changed “VDD = 2.7 to 3.6 V“ to “VDD = 3.0 to
3.6 V“
2 Added EzPort Electrical Specifications.
Updated Ta b l e 2 for part numbers.
•In Tabl e 1 3, added slew rate column, updated derive strength, pull-up/pull-down values,JTAG pin
alternate functions, removed Wired/OR control column, and reordered AN[7:0] list of pin numbers for
144 LQFP and 100 LQFP.
Updated Ta b l e 1 4 .
Updated Ta b l e 1 3 , to change MIN voltage spec for Standby Voltage (VSTBY) to 1.8V (from 3.0V).
Updated Figure 2 for RTC_EXTAL and RTC_XTAL pin positions.
3 Updated EzPort Electrical Specifications
Added hysteresis note in the DC electrical table
Clarified pin function table for VSS pins.
Clarified orderable part summary.
4 Updated EXTAL input high voltage (External reference) Maximum to "3.0V" (Instead of "VDD"). Also,
added a footnote saying, “This value has been update”
Updated crystal frequency value to 25 MHz
5 Updated TOC
Document Number: MCF52259
Rev. 5
5/2012
How to Reach Us:
Home Page:
www.freescale.com
Web Support:
http://www.freescale.com/support
USA/Europe or Locations Not Listed:
Freescale, Inc.
Technical Information Center, EL516
2100 East Elliot Road
Tempe, Arizona 85284
1-800-521-6274 or +1-480-768-2130
www.freescale.com/support
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
www.freescale.com/support
Japan:
Freescale Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
support.japan@freescale.com
Asia/Pacific:
Freescale China Ltd.
Exchange Building 23F
No. 118 Jianguo Road
Chaoyang District
Beijing 100022
China
+86 10 5879 8000
support.asia@freescale.com
Freescale Literature Distribution Center
1-800-441-2447 or +1-303-675-2140
Fax: +1-303-675-2150
LDCForFreescaleSemiconductor@hibbertgroup.com
Information in this document is provided solely to enable system and software
implementers to use Freescale products. There are no express or implied copyright
licenses granted hereunder to design or fabricate any integrated circuits or integrated
circuits based on the information in this document.
Freescale reserves the right to make changes without further notice to any products
herein. Freescale makes no warranty, representation or guarantee regarding the
suitability of its products for any particular purpose, nor does Freescale assume any
liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation consequential or incidental
damages. “Typical” parameters that may be provided in Freescale data sheets and/or
specifications can and do vary in different applications and actual performance may vary
over time. All operating parameters, including “Typicals”, must be validated for each
customer application by customer’s technical experts. Freescale does not convey any
license under its patent rights nor the rights of others. Freescale products are not
designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale product could create a
situation where personal injury or death may occur. Should Buyer purchase or use
Freescale products for any such unintended or unauthorized application, Buyer shall
indemnify and hold Freescale and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that
Freescale was negligent regarding the design or manufacture of the part.
RoHS-compliant and/or Pb-free versions of Freescale products have the functionality
and electrical characteristics as their non-RoHS-compliant and/or non-Pb-free
counterparts. For further information, see http://www.freescale.com or contact your
Freescale sales representative.
For information on Freescale’s Environmental Products program, go to
http://www.freescale.com/epp.
Freescale™ and the Freescale logo are trademarks of Freescale, Inc. All other product
or service names are the property of their respective owners.
© Freescale, Inc. 2011, 2012. All rights reserved.