LM146 LM246 LM346 PROGRAMMABLE QUAD BIPOLAR OPERATIONAL AMPLIFIER PROGRAMMABLE ELECTRICAL CHARACTERISTICS LOW SUPPLY CURRENT (250A/amplifier) GAIN-BANDWITH PRODUCT : 1MHz LARGE DC VOLTAGE GAIN : 120dB LOW NOISE VOLTAGE : 28nV/Hz WIDE POWER SUPPLY RANGE / 1.5V to 22V CLASSE AB OUTPUT STAGE. NO CROSS-OVER DISTORTION OVERLOAD PROTECTION FOR INPUTS AND OUTPUTS DESCRIPTION The LM346 consists of four independent, high gain, internally compensated, low power programmable amplifiers. Two external resistors (R set) allow the user to program the gain-bandwith product, slew rate, supply current, input bias current, input offset current and input noise. For example the user can trade-off supply current for bandwith or optimize noise figure for a given source resistance. In a similar way other amplifier characteristics can be tailored to the application. Except for the two programming pins at the end of the package the LM346 pin out is the same as the LM324 and LM348. N DIP16 (Plastic Package) PIN CONNECTIONS (top view) PROGRAMMING EQUATIONS : Total supply current = 1mA (Iset = 10A) Gain bandwith product = 1MHz (Iset = 10A) Slew rate = 0.5V/s (Iset = 10) Input bias current 30nA (Iset = 10) Iset = current into pin 8 and pin 9 (see schematic diagram) I Vcc+ - Vcc - - 0.6 V se t = ---------------------------------------------------R set ORDER CODE Part Number Temperature Range LM146 -55C, +125C LM246 -40C, +105C LM346 0C, +70C Example : LM246N Package 16 O u tp u t 4 O u tp u t 1 1 In v e rtin g In p u t 1 2 - - 15 In v e rtin g In p u t 4 N o n -in v e rtin g in p u t 1 3 + + 14 N o n -in v e rtin g in p u t 4 V CC+ 4 13 V CC - N o n -in v e rtin g In p u t 2 5 12 N o n -in v e rtin g in p u t 3 In v e rtin g In p u t 2 6 11 In v e rtin g in p u t 3 O u tp u t 2 7 10 O u tp u t 3 Set 8 9 Set N * * * N = Dual in Line Package (DIP)) April 2003 1/4 LM146-LM246-LM346 SCHEMATIC DIAGRAM (1/4 LM146) ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Supply voltage 1) Vi l Input Voltage Vid Differential Input Voltage Output Short-circuit Duration 2) 1. 2. 2/4 Value Unit 22 V 15 V 30 V Infinite Ptot Power Dissipation Toper Opearting Free-air Temperature Range LM146 LM246 LM346 -55 to +125 40 to +105 0 to +70- Tstg Storage Temperature Range -65 to +150 500 mW C C For supply voltage less than 15V, the absolute maximum input voltage is equal to the supply voltage. Any of the amplifier outputs can be shorted to ground indefinitly; however more than one should not be simultaneously shorted as the maximum junction will be exceeded. LM146-LM246-LM346 ELECTRICAL CHARACTERISTICS VCC+ = 15V, I set = 10A, Tamb = +25C (unless otherwise specified) LM146 Symbol LM246 - LM346 Parameter Unit Min. Typ. Max. 0.5 Min. Typ. Max. 3 5 0.5 5 6 Vio Input Offset Voltage (Rs 10k) Tamb = 25C Tmin Tamb Tmax Iio Input Offset Current Tamb = 25C Tmin Tamb Tmax 2 20 25 2 100 100 Iib Input Bias Current Tamb = 25C Tmin Tamb Tmax 30 100 100 30 250 250 mV nA nA Avd Large Signal Voltage Gain (Vo = 10V, RL = 10k) Tamb = 25C Tmin Tamb Tmax 100 50 1000 50 25 1000 SVR Supply Voltage Rejection Ratio (Rs 10k) Tamb = 25C Tmin Tamb Tmax 80 80 110 80 80 110 Icc V/mV dB Supply Current, all Amp, no load Tamb = 25C Tmin Tamb Tmax mA 1 Vicm Input Common Mode Voltage Range Tamb = 25C Tmin Tamb Tmax CMR Common Mode Rejection Ratio (Rs 10k) Tamb = 25C Tmin Tamb Tmax 80 70 110 Output Short-circuit Current Tamb = 25C Tmin Tamb Tmax 10 4 20 Output Voltage Swing (RL 10k) Tamb = 25C Tmin Tamb Tmax 12 12 SR Slew Rate (VI = 10V, RL = 10k, CL = 100pF, unity Gain) 0.3 RI Input Resistance CI Input Capacitance Ios Vopp 13.5 13.5 THD en Gain Bandwith Product (VI = 10 mV, RL = 10k, CL = 100pF f =100kHz) Total Harmonic Distortion (f = 1kHz, Av = 20dB, RL = 10k CL = 100pF, Vo = 2Vpp) Equivalent Input Noise Voltage (f = 1kHz, Rs = 100 1 2 2 13.5 13.5 dB 80 70 110 10 4 20 14 12 12 14 0.5 0.3 0.5 mA 30 35 30 35 V V/s 1 Vo1/Vo2 Channel Separation (RL = 10k, Vo = 12Vpp) GBP 2 2 1 M 2 2 pF 120 120 dB MHz 0.8 1 0.5 1 % 0.015 0.015 28 28 nV -----------Hz 3/4 LM146-LM246-LM346 PACKAGE MECHANICAL DATA 16 PINS - PLASTIC PACKAGE Millimeters Inches Dim. Min. a1 B b b1 D E e e3 F i L Z Typ. 0.51 0.77 Max. Min. 1.65 0.020 0.030 0.5 0.25 Typ. Max. 0.065 0.020 0.010 20 8.5 2.54 17.78 0.787 0.335 0.100 0.700 7.1 5.1 3.3 0.280 0.201 0.130 1.27 0.050 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics (c) 2003 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom http://www.st.com 4/4