ISSI IS41LV16100A 1M x 16 (16-MBIT) DYNAMIC RAM WITH EDO PAGE MODE (R) MARCH 2005 FEATURES DESCRIPTION * TTL compatible inputs and outputs; tristate I/O The ISSI IS41LV16100A is 1,048,576 x 16-bit high-performance CMOS Dynamic Random Access Memories. These devices offer an accelerated cycle access called EDO Page Mode. EDO Page Mode allows 1,024 random accesses within a single row with access cycle time as short as 20 ns per 16-bit word. * Refresh Interval: -- Auto refresh Mode: 1,024 cycles /16 ms -- RAS-Only, CAS-before-RAS (CBR), and Hidden * JEDEC standard pinout * Single power supply: -- 3.3V 10% (IS41LV16100A) * Byte Write and Byte Read operation via two CAS * Industrial Temperature Range: -40oC to +85oC These features make the IS41LV16100A ideally suited for high-bandwidth graphics, digital signal processing, highperformance computing systems, and peripheral applications. The IS41LV16100A is packaged in a 42-pin 400-mil SOJ and 400-mil 50- (44-) pin TSOP (Type II). * Lead-free available KEY TIMING PARAMETERS PIN CONFIGURATIONS 50(44)-Pin TSOP (Type II) 42-Pin SOJ VDD 1 44 GND VDD 1 42 GND I/O0 2 43 I/O15 I/O0 2 41 I/O15 I/O1 3 42 I/O14 I/O1 3 40 I/O14 I/O2 4 41 I/O13 I/O2 4 39 I/O13 I/O3 5 40 I/O12 VDD 6 39 GND I/O4 7 38 I/O11 I/O5 8 37 I/O10 I/O6 9 36 I/O7 10 35 NC 11 34 I/O3 5 38 I/O12 VDD 6 37 GND I/O4 7 36 I/O11 I/O9 I/O5 8 35 I/O10 I/O8 I/O6 9 34 I/O9 NC I/O7 10 33 I/O8 NC 11 32 NC Parameter -50 -60 Unit Max. RAS Access Time (tRAC) 50 60 ns Max. CAS Access Time (tCAC) 14 15 ns Max. Column Address Access Time (tAA) 25 30 ns Min. EDO Page Mode Cycle Time (tPC) 30 40 ns Min. Read/Write Cycle Time (tRC) 85 110 ns PIN DESCRIPTIONS A0-A9 Address Inputs I/O0-15 Data Inputs/Outputs WE Write Enable OE Output Enable NC 12 33 NC NC 12 31 LCAS NC 13 32 LCAS WE 13 30 UCAS RAS 14 29 OE NC 15 28 A9 RAS Row Address Strobe NC 16 27 A8 A0 17 26 A7 UCAS Upper Column Address Strobe LCAS Lower Column Address Strobe WE 14 31 UCAS RAS 15 30 OE NC 16 29 A9 NC 17 28 A8 A0 18 27 A7 A1 19 26 A6 A1 18 25 A6 A2 20 25 A5 A2 19 24 A5 A3 21 24 A4 A3 20 23 A4 VDD Power VDD 22 23 GND VDD 21 22 GND GND Ground NC No Connection Copyright (c) 2005 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 1 ISSI IS41LV16100A (R) FUNCTIONAL BLOCK DIAGRAM OE WE LCAS UCAS CAS CLOCK GENERATOR WE CONTROL LOGICS CAS WE OE CONTROL LOGIC OE DATA I/O BUS COLUMN DECODERS SENSE AMPLIFIERS ADDRESS BUFFERS A0-A9 2 ROW DECODER REFRESH COUNTER MEMORY ARRAY 1,048,576 x 16 DATA I/O BUFFERS RAS CLOCK GENERATOR RAS RAS I/O0-I/O15 Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 ISSI IS41LV16100A (R) TRUTH TABLE Function RAS WE OE Address tR/tC Standby H H H X X X Read: Word L L L H L ROW/COL DOUT Read: Lower Byte L L H H L ROW/COL Lower Byte, DOUT Upper Byte, High-Z Read: Upper Byte L H L H L ROW/COL Lower Byte, High-Z Upper Byte, DOUT Write: Word (Early Write) L L L L X ROW/COL DIN Write: Lower Byte (Early Write) L L H L X ROW/COL Lower Byte, DIN Upper Byte, High-Z Write: Upper Byte (Early Write) L H L L X ROW/COL Lower Byte, High-Z Upper Byte, DIN Read-Write(1,2) L L L HL LH ROW/COL DOUT, DIN EDO Page-Mode Read(2) 1st Cycle: 2nd Cycle: Any Cycle: L L L HL HL LH HL HL LH H H H L L L ROW/COL NA/COL NA/NA DOUT DOUT DOUT EDO Page-Mode Write(1) 1st Cycle: 2nd Cycle: L L HL HL HL HL L L X X ROW/COL NA/COL DIN DIN EDO Page-Mode(1,2) Read-Write 1st Cycle: 2nd Cycle: L L HL HL HL HL HL HL LH LH ROW/COL NA/COL DOUT, DIN DOUT, DIN Read(2) Write(1,3) LHL LHL L L L L H L L X ROW/COL ROW/COL DOUT DOUT L H H X X ROW/NA High-Z HL L L X X X High-Z Hidden Refresh RAS-Only Refresh CBR Refresh(4) LCAS UCAS I/O High-Z Notes: 1. These WRITE cycles may also be BYTE WRITE cycles (either LCAS or UCAS active). 2. These READ cycles may also be BYTE READ cycles (either LCAS or UCAS active). 3. EARLY WRITE only. 4. At least one of the two CAS signals must be active (LCAS or UCAS). Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 3 ISSI IS41LV16100A (R) Functional Description Auto Refresh Cycle The IS41LV16100A is a CMOS DRAM optimized for highspeed bandwidth, low power applications. During READ or WRITE cycles, each bit is uniquely addressed through the 16 address bits. These are entered ten bits (A0-A9) at time. The row address is latched by the Row Address Strobe (RAS). The column address is latched by the Column Address Strobe (CAS). RAS is used to latch the first nine bits and CAS is used to latch the latter nine bits. The IS41LV16100A has two CAS controls, LCAS and UCAS. The LCAS and UCAS inputs internally generates a CAS signal functioning in an identical manner to the single CAS input on the other 1M x 16 DRAMs. The key difference is that each CAS controls its corresponding I/O tristate logic (in conjunction with OE and WE and RAS). LCAS controls I/O0 through I/O7 and UCAS controls I/O8 through I/O15. The IS41LV16100A CAS function is determined by the first CAS (LCAS or UCAS) transitioning LOW and the last transitioning back HIGH. The two CAS controls give the IS41LV16100A both BYTE READ and BYTE WRITE cycle capabilities. To retain data, 1,024 refresh cycles are required in each 16 ms period. There are two ways to refresh the memory. 1. By clocking each of the 1,024 row addresses (A0 through A9) with RAS at least once every 128 ms. Any read, write, readmodify-write or RAS-only cycle refreshes the addressed row. Memory Cycle A memory cycle is initiated by bring RAS LOW and it is terminated by returning both RAS and CAS HIGH. To ensures proper device operation and data integrity any memory cycle, once initiated, must not be ended or aborted before the minimum tRAS time has expired. A new cycle must not be initiated until the minimum precharge time tRP, tCP has elapsed. Read Cycle A read cycle is initiated by the falling edge of CAS or OE, whichever occurs last, while holding WE HIGH. The column address must be held for a minimum time specified by tAR. Data Out becomes valid only when tRAC, tAA, tCAC and tOEA are all satisfied. As a result, the access time is dependent on the timing relationships between these parameters. Write Cycle A write cycle is initiated by the falling edge of CAS and WE, whichever occurs last. The input data must be valid at or before the falling edge of CAS or WE, whichever occurs first. 4 2. Using a CAS-before-RAS refresh cycle. CAS-beforeRAS refresh is activated by the falling edge of RAS, while holding CAS LOW. In CAS-before-RAS refresh cycle, an internal 9-bit counter provides the row addresses and the external address inputs are ignored. CAS-before-RAS is a refresh-only mode and no data access or device selection is allowed. Thus, the output remains in the High-Z state during the cycle. Extended Data Out Page Mode EDO page mode operation permits all 1,024 columns within a selected row to be randomly accessed at a high data rate. In EDO page mode read cycle, the data-out is held to the next CAS cycle's falling edge, instead of the rising edge. For this reason, the valid data output time in EDO page mode is extended compared with the fast page mode. In the fast page mode, the valid data output time becomes shorter as the CAS cycle time becomes shorter. Therefore, in EDO page mode, the timing margin in read cycle is larger than that of the fast page mode even if the CAS cycle time becomes shorter. In EDO page mode, due to the extended data function, the CAS cycle time can be shorter than in the fast page mode if the timing margin is the same. The EDO page mode allows both read and write operations during one RAS cycle, but the performance is equivalent to that of the fast page mode in that case. Power-On After application of the VDD supply, an initial pause of 200 s is required followed by a minimum of eight initialization cycles (any combination of cycles containing a RAS signal). During power-on, it is recommended that RAS track with VDD or be held at a valid VIH to avoid current surges. Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 ISSI IS41LV16100A (R) ABSOLUTE MAXIMUM RATINGS(1) Symbol Parameters Rating Unit VT Voltage on Any Pin Relative to GND 3.3V -0.5 to +4.6 V VDD Supply Voltage 3.3V -0.5 to +4.6 V IOUT Output Current 50 mA PD Power Dissipation 1 W TA Commercial Operation Temperature Industrial Operation Temperature 0 to +70 -40 to +85 C C TSTG Storage Temperature -55 to +125 C Note: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. RECOMMENDED OPERATING CONDITIONS (Voltages are referenced to GND.) Symbol Parameter Min. Typ. Max. Unit VDD Supply Voltage 3.3V 3.0 3.3 3.6 V VIH Input High Voltage 3.3V 2.0 -- VDD + 0.3 V VIL Input Low Voltage 3.3V -0.3 -- 0.8 V TA Commercial Ambient Temperature Industrial Ambient Temperature 0 -40 -- -- 70 85 C C CAPACITANCE(1,2) Symbol Parameter Max. Unit CIN1 Input Capacitance: A0-A9 5 pF CIN2 Input Capacitance: RAS, UCAS, LCAS, WE, OE 7 pF CIO Data Input/Output Capacitance: I/O0-I/O15 7 pF Notes: 1. Tested initially and after any design or process changes that may affect these parameters. 2. Test conditions: TA = 25C, f = 1 MHz. Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 5 ISSI IS41LV16100A (R) ELECTRICAL CHARACTERISTICS(1) (Recommended Operating Conditions unless otherwise noted.) Symbol Parameter Test Condition IIL Input Leakage Current IIO Speed Min. Max. Unit Any input 0V VIN VDD Other inputs not under test = 0V -10 10 A Output Leakage Current Output is disabled (Hi-Z) 0V VOUT VDD -10 10 A VOH Output High Voltage Level IOH = -2.0 mA (3.3V) 2.4 -- V VOL Output Low Voltage Level IOL = 2.0 mA (3.3V) -- 0.4 V ICC1 Standby Current: TTL RAS, LCAS, UCAS VIH -- -- 3 4 mA mA ICC2 Standby Current: CMOS RAS, LCAS, UCAS VDD - 0.2V 3.3V -- 2 mA ICC3 Operating Current: Random Read/Write(2,3,4) Average Power Supply Current RAS, LCAS, UCAS, Address Cycling, tRC = tRC (min.) -50 -60 -- -- 180 170 mA ICC4 Operating Current: EDO Page Mode(2,3,4) Average Power Supply Current RAS = VIL, LCAS, UCAS, Cycling tPC = tPC (min.) -50 -60 -- -- 180 170 mA ICC5 Refresh Current: RAS-Only(2,3) Average Power Supply Current RAS Cycling, LCAS, UCAS VIH tRC = tRC (min.) -50 -60 -- -- 180 170 mA ICC6 Refresh Current: CBR(2,3,5) Average Power Supply Current RAS, LCAS, UCAS Cycling tRC = tRC (min.) -50 -60 -- -- 180 170 mA Commercial 3.3V Industrial 3.3V Notes: 1. An initial pause of 200 s is required after power-up followed by eight RAS refresh cycles (RAS-Only or CBR) before proper device operation is assured. The eight RAS cycles wake-up should be repeated any time the tREF refresh requirement is exceeded. 2. Dependent on cycle rates. 3. Specified values are obtained with minimum cycle time and the output open. 4. Column-address is changed once each EDO page cycle. 5. Enables on-chip refresh and address counters. 6 Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 ISSI IS41LV16100A (R) AC CHARACTERISTICS(1,2,3,4,5,6) (Recommended Operating Conditions unless otherwise noted.) -50 Symbol Parameter -60 Min. Max. Min. Max. Units tRC Random READ or WRITE Cycle Time 85 -- 110 -- ns tRAC Access Time from RAS -- 50 -- 60 ns tCAC Access Time from CAS -- 14 -- 15 ns (6, 7) (6, 8, 15) (6) tAA Access Time from Column-Address -- 25 -- 30 ns tRAS RAS Pulse Width 50 10K 60 10K ns tRP RAS Precharge Time 30 -- 40 -- ns tCAS CAS Pulse Width 8 10K 10 10K ns tCP CAS Precharge Time 9 -- 10 -- ns tCSH CAS Hold Time 50 -- 60 -- ns tRCD RAS to CAS Delay Time 12 37 20 45 ns tASR Row-Address Setup Time 0 -- 0 -- ns tRAH Row-Address Hold Time 8 -- 10 -- ns 0 -- 0 -- ns 8 -- 10 -- ns tASC (26) (9, 25) (21) (10, 20) (20) Column-Address Setup Time (20) tCAH Column-Address Hold Time tAR 30 -- 40 -- ns tRAD Column-Address Hold Time (referenced to RAS) RAS to Column-Address Delay Time(11) 14 25 15 30 ns tRAL Column-Address to RAS Lead Time 25 -- 30 -- ns tRPC RAS to CAS Precharge Time 5 -- 5 -- ns tRSH RAS Hold Time 14 -- 15 -- ns tCLZ CAS to Output in Low-Z 0 -- 0 -- ns tCRP CAS to RAS Precharge Time 5 -- 5 -- ns 3 12 3 12 ns -- 14 -- 15 ns tOD (27) (15, 29) (21) (19, 28, 29) Output Disable Time (15, 16) tOE/tOEA Output Enable Time tOEHC OE HIGH Hold Time from CAS HIGH 15 -- 15 -- ns tOEP OE HIGH Pulse Width 10 -- 10 -- ns tOES OE LOW to CAS HIGH Setup Time 5 -- 5 -- ns (17, 20) tRCS Read Command Setup Time 0 -- 0 -- ns tRRH Read Command Hold Time (referenced to RAS)(12) Read Command Hold Time (referenced to CAS)(12, 17, 21) Write Command Hold Time(17, 27) 0 -- 0 -- ns 0 -- 0 -- ns 8 -- 10 -- ns 40 -- 50 -- ns tRCH tWCH tWCR Write Command Hold Time (referenced to RAS)(17) Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 7 ISSI IS41LV16100A (R) AC CHARACTERISTICS (Continued)(1,2,3,4,5,6) (Recommended Operating Conditions unless otherwise noted.) -50 Symbol 8 Parameter (17) -60 Min. Max. Min. Max. Units tWP Write Command Pulse Width 8 -- 10 -- ns tWPZ WE Pulse Widths to Disable Outputs 10 -- 10 -- ns t RWL Write Command to RAS Lead Time(17) 13 -- 15 -- ns tCWL Write Command to CAS Lead Time 8 -- 15 -- ns tWCS Write Command Setup Time (14, 17, 20) 0 -- 0 -- ns tDHR Data-in Hold Time (referenced to RAS) 39 -- 40 -- ns tOEH OE Hold Time from WE during READ-MODIFY-WRITE cycle(18) 14 -- 15 -- ns tDS Data-In Setup Time(15, 22) 0 -- 0 -- ns 8 -- 15 -- ns (17, 21) (15, 22) tDH Data-In Hold Time tRWC READ-MODIFY-WRITE Cycle Time 110 -- 155 -- ns tRWD RAS to WE Delay Time during READ-MODIFY-WRITE Cycle(14) 65 -- 85 -- ns tCWD CAS to WE Delay Time(14, 20) 26 -- 40 -- ns tAWD Column-Address to WE Delay Time 40 -- 55 -- ns tPC EDO Page Mode READ or WRITE Cycle Time(24) 30 -- 40 -- ns tRASP RAS Pulse Width in EDO Page Mode 50 100K 60 100K ns tCPA Access Time from CAS Precharge -- 30 -- 35 ns tPRWC EDO Page Mode READ-WRITE Cycle Time(24) 56 -- 56 -- ns tCOH Data Output Hold after CAS LOW 5 -- 5 -- ns tOFF Output Buffer Turn-Off Delay from CAS or RAS(13,15,19, 29) 3 12 3 15 ns tWHZ Output Disable Delay from WE 3 10 3 15 ns tCLCH Last CAS going LOW to First CAS returning HIGH(23) 10 -- 10 -- ns tCSR CAS Setup Time (CBR REFRESH)(30, 20) 5 -- 5 -- ns tCHR CAS Hold Time (CBR REFRESH)(30, 21) 8 -- 10 -- ns tORD OE Setup Time prior to RAS during HIDDEN REFRESH Cycle 0 -- 0 -- ns tREF Auto Refresh Period (1,024 Cycles) -- 16 -- 16 ms tT Transition Time (Rise or Fall)(2, 3) 3 50 3 50 ns (14) (15) Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 IS41LV16100A ISSI (R) AC TEST CONDITIONS Output load: One TTL Load and 50 pF (VDD = 3.3V 10%) Input timing reference levels: VIH = 2.0V, VIL = 0.8V (VDD = 3.3V 10%) Output timing reference levels: VOH = 2.0V, VOL = 0.8V Notes: 1. An initial pause of 200 s is required after power-up followed by eight RAS refresh cycle (RAS-Only or CBR) before proper device operation is assured. The eight RAS cycles wake-up should be repeated any time the tREF refresh requirement is exceeded. 2. VIH (MIN) and VIL (MAX) are reference levels for measuring timing of input signals. Transition times, are measured between VIH and VIL (or between VIL and VIH) and assume to be 1 ns for all inputs. 3. In addition to meeting the transition rate specification, all input signals must transit between VIH and VIL (or between VIL and VIH) in a monotonic manner. 4. If CAS and RAS = VIH, data output is High-Z. 5. If CAS = VIL, data output may contain data from the last valid READ cycle. 6. Measured with a load equivalent to one TTL gate and 50 pF. 7. Assumes that tRCD tRCD (MAX). If tRCD is greater than the maximum recommended value shown in this table, tRAC will increase by the amount that tRCD exceeds the value shown. 8. Assumes that tRCD tRCD (MAX). 9. If CAS is LOW at the falling edge of RAS, data out will be maintained from the previous cycle. To initiate a new cycle and clear the data output buffer, CAS and RAS must be pulsed for tCP. 10. Operation with the tRCD (MAX) limit ensures that tRAC (MAX) can be met. tRCD (MAX) is specified as a reference point only; if tRCD is greater than the specified tRCD (MAX) limit, access time is controlled exclusively by tCAC. 11. Operation within the tRAD (MAX) limit ensures that tRCD (MAX) can be met. tRAD (MAX) is specified as a reference point only; if tRAD is greater than the specified tRAD (MAX) limit, access time is controlled exclusively by tAA. 12. Either tRCH or tRRH must be satisfied for a READ cycle. 13. tOFF (MAX) defines the time at which the output achieves the open circuit condition; it is not a reference to VOH or VOL. 14. tWCS, tRWD, tAWD and tCWD are restrictive operating parameters in LATE WRITE and READ-MODIFY-WRITE cycle only. If tWCS tWCS (MIN), the cycle is an EARLY WRITE cycle and the data output will remain open circuit throughout the entire cycle. If tRWD tRWD (MIN), tAWD tAWD (MIN) and tCWD tCWD (MIN), the cycle is a READ-WRITE cycle and the data output will contain data read from the selected cell. If neither of the above conditions is met, the state of I/O (at access time and until CAS and RAS or OE go back to VIH) is indeterminate. OE held HIGH and WE taken LOW after CAS goes LOW result in a LATE WRITE (OE-controlled) cycle. 15. Output parameter (I/O) is referenced to corresponding CAS input, I/O0-I/O7 by LCAS and I/O8-I/O15 by UCAS. 16. During a READ cycle, if OE is LOW then taken HIGH before CAS goes HIGH, I/O goes open. If OE is tied permanently LOW, a LATE WRITE or READ-MODIFY-WRITE is not possible. 17. Write command is defined as WE going low. 18. LATE WRITE and READ-MODIFY-WRITE cycles must have both tOD and tOEH met (OE HIGH during WRITE cycle) in order to ensure that the output buffers will be open during the WRITE cycle. The I/Os will provide the previously written data if CAS remains LOW and OE is taken back to LOW after tOEH is met. 19. The I/Os are in open during READ cycles once tOD or tOFF occur. 20. The first CAS edge to transition LOW. 21. The last CAS edge to transition HIGH. 22. These parameters are referenced to CAS leading edge in EARLY WRITE cycles and WE leading edge in LATE WRITE or READMODIFY-WRITE cycles. 23. Last falling CAS edge to first rising CAS edge. 24. Last rising CAS edge to next cycle's last rising CAS edge. 25. Last rising CAS edge to first falling CAS edge. 26. Each CAS must meet minimum pulse width. 27. Last CAS to go LOW. 28. I/Os controlled, regardless UCAS and LCAS. 29. The 3 ns minimum is a parameter guaranteed by design. 30. Enables on-chip refresh and address counters. Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 9 ISSI IS41LV16100A (R) READ CYCLE tRC tRAS tRP RAS tCSH tCRP tRSH tCAS tCLCH tRCD tRRH UCAS/LCAS tAR tRAD tRAH tASR ADDRESS tRAL tCAH tASC Row Column Row tRCS tRCH WE tAA tRAC tCAC tCLC I/O tOFF(1) Open Open Valid Data tOE tOD OE tOES Undefined Don't Care Note: 1. tOFF is referenced from rising edge of RAS or CAS, whichever occurs last. 10 Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 ISSI IS41LV16100A (R) EARLY WRITE CYCLE (OE = DON'T CARE) tRC tRAS tRP RAS tCSH tCRP tRSH tCAS tCLCH tRCD UCAS/LCAS tAR tRAD tRAH tASR ADDRESS tRAL tCAH tACH tASC Row Column Row tCWL tRWL tWCR tWCS tWCH tWP WE tDHR tDS I/O tDH Valid Data Don't Care Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 11 ISSI IS41LV16100A (R) READ WRITE CYCLE (LATE WRITE and READ-MODIFY-WRITE Cycles) tRWC tRAS tRP RAS tCSH tCRP tRSH tCAS tCLCH tRCD UCAS/LCAS tAR tRAD tASR tRAL tRAH tCAH tASC tACH ADDRESS Row Column Row tRWD tCWL tRWL tCWD tRCS tAWD tWP WE tAA tRAC tCAC tCLZ I/O tDS Open Valid DOUT tOE tOD tDH Valid DIN Open tOEH OE Undefined Don't Care 12 Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 ISSI IS41LV16100A (R) EDO-PAGE-MODE READ CYCLE tRASP tRP RAS tCSH tCRP tCAS, tCLCH tRCD tPC(1) tCAS, tCP tCLCH tCP tRSH tCAS, tCLCH tCP UCAS/LCAS tAR tRAD tASR ADDRESS tASC tCAH tASC Row Column tRAL tCAH tCAH tASC Column Column Row tRAH tRRH tRCS tRCH WE tAA tRAC tCAC tCLZ I/O Open tAA tCPA tAA tCPA tCAC tCOH Valid Data tOE tOES tCAC tCLZ tOFF Valid Data tOEHC Valid Data Open tOE tOD tOES tOD OE tOEP Undefined Don't Care Note: 1. tPC can be measured from falling edge of CAS to falling edge of CAS, or from rising edge of CAS to rising edge of CAS. Both measurements must meet the tPC specifications. Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 13 ISSI IS41LV16100A (R) EDO-PAGE-MODE EARLY-WRITE CYCLE tRASP tRP tRHCP RAS tCSH tCRP tPC tCAS, tCLCH tRCD tCP tCAS, tCLCH tCP tRSH tCAS, tCLCH tCP UCAS/LCAS tAR tACH tCAH tASC tRAD tASR ADDRESS tASC Row Column tRAH tACH tRAL tCAH tACH tCAH tASC Column tCWL tWCS Column tCWL tWCS tWCH tCWL tWCS tWCH tWCH tWP tWP Row tWP WE tWCR tDHR tRWL tDS tDS tDH I/O tDS tDH Valid Data Valid Data tDH Valid Data OE Don't Care 14 Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 ISSI IS41LV16100A (R) EDO-PAGE-MODE READ-WRITE CYCLE (LATE WRITE and READ-MODIFY WRITE Cycles) tRASP tRP RAS tCSH tCRP tCAS, tCLCH tRCD tCP tPC / tPRWC(1) tCAS, tCLCH tRSH tCAS, tCLCH tCP tCP UCAS/LCAS tASR tRAH ADDRESS tAR tRAD tASC tCAH Row tASC tCAH Column tRWD tRCS tRAL tCAH tASC Column tCWL tWP Column tRWL tCWL tWP tCWL tWP tAWD tCWD Row tAWD tCWD tAWD tCWD WE tAA tAA tCPA tDH tRAC tDS tDS tCAC tCLZ I/O Open tCAC tCLZ DOUT DIN tDH tDS tCAC tCLZ DOUT tOD tOE tAA tCPA tDH DIN DOUT tOD tOE Open DIN tOD tOE tOEH OE Undefined Don't Care Note: 1. tPC can be measured from falling edge of CAS to falling edge of CAS, or from rising edge of CAS to rising edge of CAS. Both measurements must meet the tPC specifications. Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 15 ISSI IS41LV16100A (R) EDO-PAGE-MODE READ-EARLY-WRITE CYCLE (Pseudo READ-MODIFY WRITE) tRASP tRP RAS tCSH tPC tPC tCRP tCAS tRCD tCAS tCP tRSH tCAS tCP tCP UCAS/LCAS tASR tRAH ADDRESS tAR tRAD tASC Row tCAH tASC tCAH Column (A) tASC Column (B) tRCS tACH tRAL tCAH Column (N) Row tRCH tWCS tWCH WE tAA tRAC tCAC tCPA tCAC tAA tWHZ tCOH I/O Open Valid Data (A) tDS Valid Data (B) tDH DIN Open tOE OE Don't Care 16 Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 ISSI IS41LV16100A (R) AC WAVEFORMS READ CYCLE (With WE-Controlled Disable) RAS tCSH tCRP tRCD tCP tCAS UCAS/LCAS tAR tRAD tASR ADDRESS tRAH tCAH tASC Row tASC Column Column tRCS tRCH tRCS WE tAA tRAC tCAC tCLZ Open I/O tWHZ tCLZ Valid Data Open tOE tOD OE Undefined Don't Care RAS RAS-ONLY REFRESH CYCLE (OE, WE = DON'T CARE) tRC tRAS tRP RAS tCRP tRPC UCAS/LCAS tASR ADDRESS I/O tRAH Row Row Open Don't Care Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 17 ISSI IS41LV16100A (R) CBR REFRESH CYCLE (Addresses; WE, OE = DON'T CARE) tRP tRAS tRP tRAS RAS tCHR tRPC tCP tCHR tRPC tCSR tCSR UCAS/LCAS Open I/O HIDDEN REFRESH CYCLE(1) (WE = HIGH; OE = LOW) tRAS tRP tRAS RAS tCRP tRCD tASR tRAD tRAH tASC tRSH tCHR UCAS/LCAS tAR ADDRESS Row tRAL tCAH Column tAA tRAC tOFF(2) tCAC tCLZ I/O Open Valid Data tOE Open tOD tORD OE Undefined Don't Care Notes: 1. A Hidden Refresh may also be performed after a Write Cycle. In this case, WE = LOW and OE = HIGH. 2. tOFF is referenced from rising edge of RAS or CAS, whichever occurs last. 18 Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 ISSI IS41LV16100A (R) ORDERING INFORMATION : 3.3V Commercial Range: 0C to +70C Speed (ns) Order Part No. Package 50 IS41LV16100A-50K IS41LV16100A-50KL IS41LV16100A-50T IS41LV16100A-50TL 400-mil SOJ 400-mil SOJ, Lead-free 400-mil TSOP (Type II) 400-mil TSOP (Type II), Lead-free 60 IS41LV16100A-60K IS41LV16100A-60KL IS41LV16100A-60T IS41LV16100A-60TL 400-mil SOJ 400-mil SOJ, Lead-free 400-mil TSOP (Type II) 400-mil TSOP (Type II), Lead-free Industrial Range: -40C to +85C Speed (ns) Order Part No. Package 50 IS41LV16100A-50KI IS41LV16100A-50KLI IS41LV16100A-50TI IS41LV16100A-50TLI 400-mil SOJ 400-mil SOJ, Lead-free 400-mil TSOP (Type II) 400-mil TSOP (Type II), Lead-free 60 IS41LV16100A-60KI IS41LV16100A-60KLI IS41LV16100A-60TI IS41LV16100A-60TLI 400-mil SOJ 400-mil SOJ, Lead-free 400-mil TSOP (Type II) 400-mil TSOP (Type II), Lead-free Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. B 03/02/05 19 ISSI PACKAGING INFORMATION (R) 400-mil Plastic SOJ Package Code: K N Notes: 1. Controlling dimension: millimeters. 2. BSC = Basic lead spacing between centers. 3. Dimensions D and E1 do not include mold flash protrusions and should be measured from the bottom of the package. 4. Reference document: JEDEC MS-027. N/2+1 E1 1 E N/2 SEATING PLANE D b A C A2 e Symbol No. Leads A A1 A2 B b C D E E1 E2 e B Millimeters Inches Min Max Min Max (N) 28 3.25 3.75 0.128 0.148 0.64 -- 0.025 -- 2.08 -- 0.082 -- 0.38 0.51 0.015 0.020 0.66 0.81 0.026 0.032 0.18 0.33 0.007 0.013 18.29 18.54 0.720 0.730 11.05 11.30 0.435 0.445 10.03 10.29 0.395 0.405 9.40 BSC 0.370 BSC 1.27 BSC 0.050 BSC A1 E2 Millimeters Min Max Inches Min Max Millimeters Min Max 32 3.25 3.75 0.64 -- 2.08 -- 0.38 0.51 0.66 0.81 0.18 0.33 20.82 21.08 11.05 11.30 10.03 10.29 9.40 BSC 1.27 BSC 0.128 0.148 0.025 -- 0.082 -- 0.015 0.020 0.026 0.032 0.007 0.013 0.820 0.830 0.435 0.445 0.395 0.405 0.370 BSC 0.050 BSC 3.25 3.75 0.64 -- 2.08 -- 0.38 0.51 0.66 0.81 0.18 0.33 23.37 23.62 11.05 11.30 10.03 10.29 9.40 BSC 1.27 BSC Inches Min Max 36 0.128 0.148 0.025 -- 0.082 -- 0.015 0.020 0.026 0.032 0.007 0.013 0.920 0.930 0.435 0.445 0.395 0.405 0.370 BSC 0.050 BSC Copyright (c) 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. F 10/29/03 ISSI PACKAGING INFORMATION Millimeters Inches Symbol Min Max Min Max No. Leads (N) 40 A 3.25 3.75 0.128 0.148 A1 0.64 -- 0.025 -- A2 2.08 -- 0.082 -- B 0.38 0.51 0.015 0.020 b 0.66 0.81 0.026 0.032 C 0.18 0.33 0.007 0.013 D 25.91 26.16 1.020 1.030 E 11.05 11.30 0.435 0.445 E1 10.03 10.29 0.395 0.405 E2 9.40 BSC 0.370 BSC e 1.27 BSC 0.050 BSC Millimeters Min Max Inches Min Max Millimeters Min Max 42 3.25 3.75 0.64 -- 2.08 -- 0.38 0.51 0.66 0.81 0.18 0.33 27.18 27.43 11.05 11.30 10.03 10.29 9.40 BSC 1.27 BSC 0.128 0.148 0.025 -- 0.082 -- 0.015 0.020 0.026 0.032 0.007 0.013 1.070 1.080 0.435 0.445 0.395 0.405 0.370 BSC 0.050 BSC 3.25 3.75 0.64 -- 2.08 -- 0.38 0.51 0.66 0.81 0.18 0.33 28.45 28.70 11.05 11.30 10.03 10.29 9.40 BSC 1.27 BSC (R) Inches Min Max 44 0.128 0.148 0.025 -- 0.082 -- 0.015 0.020 0.026 0.032 0.007 0.013 1.120 1.130 0.435 0.445 0.395 0.405 0.370 BSC 0.050 BSC Copyright (c) 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. 2 Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774 Rev. F 10/29/03 ISSI PACKAGING INFORMATION Plastic TSOP Package Code: T (Type II) N N/2+1 E1 E 1 Notes: 1. Controlling dimension: millimeters, unless otherwise specified. 2. BSC = Basic lead spacing between centers. 3. Dimensions D1 and E do not include mold flash protrusions and should be measured from the bottom of the package. 4. Formed leads shall be planar with respect to one another within 0.004 inches at the seating plane. N/2 D SEATING PLANE A e Plastic TSOP (T - Type II) (MS 25) Millimeters Inches Symbol Min Max Min Max Ref. Std. N 24/26 A 1.20 0.0472 A1 0.05 0.15 0.002 0.0059 b 0.30 0.51 0.012 0.0201 c 0.12 0.21 0.005 0.0083 D 17.01 17.27 0.670 0.6899 E1 7.49 7.75 0.295 0.3051 e 1.27 BSC 0.050 BSC E 9.02 9.42 0.462 0.4701 L 0.40 0.60 0.016 0.0236 0 5 0 5 Integrated Silicon Solution, Inc. PK13197T40 Rev. C 08/013/99 (R) b L A1 Plastic TSOP (T - Type II) (MS 24) Millimeters Inches Symbol Min Max Min Max Ref. Std. N 40/44 A 1.20 0.0472 A1 0.05 0.15 0.002 0.0059 b 0.30 0.45 0.012 0.0157 c 0.12 0.21 0.005 0.0083 D 18.31 18.51 0.721 0.7287 E1 10.06 10.26 0.396 0.4040 e 0.80 BSC 0.031 BSC E 11.56 11.96 0.455 0.4709 L 0.40 0.60 0.016 0.0236 0 8 0 8 c Plastic TSOP (T - Type II) (MS 24) Millimeters Inches Symbol Min Max Min Max Ref. Std. N 44/50 A 1.20 0.0472 A1 0.05 0.15 0.002 0.0059 b 0.30 0.45 0.012 0.0157 c 0.12 0.21 0.005 0.0083 D 20.85 21.05 0.821 0.8287 E1 10.06 10.26 0.396 0.4040 e 0.80 BSC 0.031 BSC E 11.56 11.96 0.455 0.4709 L 0.40 0.60 0.016 0.0236 0 8 0 8