2SC4672 Transistors Low Frequency Transistor (50V, 3A) 2SC4672 zFeatures 1) Low saturation voltage, typically VCE (sat) =0.1V at IC/IB =1A /50mA. 2) Excellent DC current gain characteristics. 3) Complements the 2SA1797. zAbsolute maximum ratings (Ta=25C) Symbol Limits Unit Collector-base voltage Collector-emitter voltage VCBO VCEO 60 50 V V Emitter-base voltage VEBO 6 3 6 V A (DC) A (Pulse) W Parameter Collector current IC Collector power dissipation PC 0.5 2 Junction temperature Tj 150 Storage temperature Tstg -55 to +150 2 1 C C 1 Single pulse, Pw=10ms 2 40x40x t 0.7mm Ceramic board zPackaging specifications and hFE Type 2SC4672 Package hFE MPT3 PQ DK Marking Code Basic ordering unit (pieces) T100 1000 Denotes hFE hFE values are classified as follows: Item P Q hFE 82 to 180 120 to 270 zElectrical characteristics (Ta=25C) Parameter Symbol Min. Typ. Max. Unit Collector-base breakdown voltage Collector-emitter breakdown voltage Emitter-base breakdown voltage BVCBO BVCEO - - - - - BVEBO 60 50 6 Collector cutoff current Emitter cutoff current Collector-emitter saturation voltage ICBO - - 0.1 V V V A VCB=60V IEBO - 0.1 0.35 A V VEB=5V DC current transfer ratio Transition frequency Output capacitance VCE(sat) - - - 0.13 hFE1 82 - 270 - hFE2 45 - fT - - - 210 25 - MHz pF Cob - - Conditions IC=50A IC=1mA IE=50A IC/IB=1A/50mA VCE=2V, IC=0.5A VCE=2V, IC=1.5A VCE=2V, IE=-0.5A, f=100MHz VCB=10V, IE=0A, f=1MHz Measured using pulse current. Rev.C 1/2 2SC4672 Transistors 5000 2000 Ta=25C 2 1 0.5 0.2 VCE=2V VCE= -2V DC CURRENT GAIN : hFE COLLECTOR CURRENT : IC(A) 10 5 Ta=100C 0.1 Ta= -40C 0.05 0.02 0.01 5m 1000 500 Ta=100C Ta=25C 200 100 50 Ta= -40C 20 10 2m 1m 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 BASE TO EMITTER VOLTAGE : VBE (V) Fig.1 Grounded emitter propagation characteristics COLLECTOR CURRENT : IC (A) 10 5 Ic Max. (Pulse) 5 1m 2m 5m 0.01 0.02 0.05 0.1 0.2 0.5 1 2 5 10 COLLECTOR CURRENT : IC (A) Fig.2 DC current gain vs. collector current COLLECTOR SATURATION VOLTAGE : VCE(sat) (V) zElectrical characteristics curves 1 IC/IB=20 0.5 Ta=100C 0.2 Ta=25C 0.1 0.05 Ta= -40C 0.02 0.01 1m 2m 5m 0.01 0.02 0.05 0.1 0.2 0.5 1 2 5 10 COLLECTOR CURRENT : IC (A) Fig.3 Collector-emitter saturation voltage vs. collector current Pw=1ms Pw=10ms 2 1 500m Pw=100ms 200m DC 100m 50m 20m 10m 5m Ta=25C Single 2m NONREPETITIVE PULSE 1m 0.1 0.2 0.5 1 2 5 10 20 50 100 200 500 1000 COLLECTOR TO EMITTER VOLTAGE : VCE (V) Fig.4 Safe Operating area Rev.C 2/2 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright (c) 2008 ROHM CO.,LTD. THE AMERICAS / EUROPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0