DS99R105/DS99R106 3-40MHz DC-Balanced 24-Bit LVDS Serializer and Deserializer General Description Internal DC Balancing encode/decode - Supports AC- The DS99R105/DS99R106 Chipset translates a 24-bit parallel bus into a fully transparent data/control LVDS serial stream with embedded clock information. This single serial stream simplifies transferring a 24-bit bus over PCB traces and cable by eliminating the skew problems between parallel data and clock paths. It saves system cost by narrowing data paths that in turn reduce PCB layers, cable width, and connector size and pins. The DS99R105/DS99R106 incorporates LVDS signaling on the high-speed I/O. LVDS provides a low power and low noise environment for reliably transferring data over a serial transmission path. By optimizing the serializer output edge rate for the operating frequency range EMI is further reduced. In addition the device features pre-emphasis to boost signals over longer distances using lossy cables. Internal DC balanced encoding/decoding is used to support AC-Coupled interconnects. Features 3 MHz-40 MHz clock embedded and DC-Balancing 24:1 and 1:24 data transmissions Capable to drive shielded twisted-pair cable User selectable clock edge for parallel data on both Transmitter and Receiver coupling interface with no external coding required Individual power-down controls for both Transmitter and Receiver Embedded clock CDR (clock and data recovery) on Receiver and no external source of reference clock needed All codes RDL (random data lock) to support livepluggable applications LOCK output flag to ensure data integrity at Receiver side Balanced TSETUP/THOLD between RCLK and RDATA on Receiver side PTO (progressive turn-on) LVCMOS outputs to reduce EMI and minimize SSO effects All LVCMOS inputs and control pins have internal pulldown On-chip filters for PLLs on Transmitter and Receiver Integrated 100 input termination on Receiver 4 mA Receiver output drive 48-pin TQFP and 48-pin LLP packages Pure CMOS .35 m process Power supply range 3.3V 10% Temperature range 0C to +70C 8 kV HBM ESD tolerance Block Diagram 20208101 TRI-STATE(R) is a registered trademark of National Semiconductor Corporation. (c) 2007 National Semiconductor Corporation 202081 www.national.com DS99R105/DS99R106 3-40MHz DC-Balanced 24-Bit LVDS Serializer and Deserializer October 2007 DS99R105/DS99R106 Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. DS99R105 Supply Voltage (VDD) -0.3V to +4V LVCMOS/LVTTL Input Voltage -0.3V to (VDD +0.3V) LVCMOS/LVTTL Output Voltage -0.3V to (VDD +0.3V) LVDS Receiver Input Voltage -0.3V to 3.9V LVDS Driver Output Voltage -0.3V to 3.9V LVDS Output Short Circuit Duration 10 ms Junction Temperature +150C Storage Temperature -65C to +150C Lead Temperature (Soldering, 4 seconds) +260C Maximum Package Power Dissipation Capacity Package De-rating: 48L TQFP 1/JA C/W above +25C JA 45.4 (4L*); 75.0 (2L*)C/W JC 21.1C/W JA 28 (4L*); 79.1 (2L*)C/W JC 3.71C/W *JEDEC 8 kV Recommended Operating Conditions Supply Voltage (VDD) Operating Free Air Temperature (TA) Clock Rate Supply Noise 21.0C/W JA 3.7C/W ESD Rating (HBM) 45.8 (4L*); 75.4 (2L*) C/W JC DS99R106 28 (4L*); 79.1 (2L*) C/W JC DS99R106 DS99R105 JA 1/JA C/W above +25C 48L LLP Min 3.0 Nom 3.3 Max 3.6 Units V 0 3 +25 +70 40 100 C MHz mVP-P Electrical Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Pin/Freq. Min Typ Max Units 2.0 1.5 VDD V GND 1.5 0.8 V -0.8 -1.5 V LVCMOS/LVTTL DC SPECIFICATIONS VIH High Level Voltage VIL Low Level Input Voltage VCL Input Clamp Voltage IIN Input Current ICL = -18 mA (Note 8) VIN = 0V or 3.6V VOH High Level Output Voltage IOH = -4 mA VOL Low Level Output Voltage IOL = +4 mA IOS Output Short Circuit Current VOUT = 0V (Note 8) IOZ TRI-STATE(R) Output Current RPWDNB, REN = 0V VOUT = 0V or 2.4V www.national.com Tx: DIN[23:0], TCLK, TPWDNB, DEN, TRFB, DCAOFF, DCBOFF, VODSEL Rx: RPWDNB, RRFB, REN Tx: DIN[23:0], TCLK, TPWDNB, DEN, TRFB, DCAOFF, DCBOFF, VODSEL -10 1 +10 A Rx: RPWDNB, RRFB, REN -20 5 +20 A 2.3 3.0 VDD V GND 0.33 0.5 V Rx: ROUT[23:0], RCLK, LOCK Rx: ROUT[23:0], RCLK, LOCK 2 -40 -70 -110 mA -30 0.4 +30 A Parameter Conditions Pin/Freq. Min Typ Max Units +50 mV LVDS DC SPECIFICATIONS VTH Differential Threshold High Voltage VTL Differential Threshold Low Voltage IIN Input Current RT Differential Internal Termination Resistance VOD Output Differential Voltage (DOUT+)-(DOUT-) VCM = +1.2V Rx: RIN+, RIN- -50 mV VIN = +2.4V, VDD = 3.6V 300 A VIN = 0V, VDD = 3.6V 300 A RL = 100, w/o Pre-emphasis VODSEL = L (Figure 10) Tx: DOUT+, DOUT- RL = 100, w/o Pre-emphasis VODSEL = H (Figure 10) 90 100 130 250 400 600 mV 450 750 1200 mV 4 50 mV 1.50 V 1 50 mV VOD Output Differential Voltage Unbalance RL = 100, w/o Pre-emphasis VOS Offset Voltage RL = 100, w/o Pre-emphasis VOS Offset Voltage Unbalance RL = 100, w/o Pre-emphasis IOS Output Short Circuit Current DOUT = 0V, DIN = H, TPWDNB, DEN = 2.4V, VODSEL = L -2 -5 -8 mA DOUT = 0V, DIN = H, TPWDNB, DEN = 2.4V, VODSEL = H -7 -10 -13 mA TPWDNB, DEN = 0V, DOUT = 0V or 2.4V -15 1 +15 A 40 80 mA 45 85 mA 40 85 mA 45 90 mA 1 100 A IOZ TRI-STATE Output Current 1.00 1.25 SER/DES SUPPLY CURRENT (DVDD*, PVDD* and AVDD* pins) *Digital, PLL, and Analog VDDs IDDT Serializer (Tx) Total Supply Current (includes load current) Serializer (Tx) Total Supply Current (includes load current) IDDTZ Serializer (Tx) Supply Current Power-down RL = 100 Pre-emphasis = OFF VODSEL = L Checker-board pattern (Figure 1) f = 40 MHz RL = 100 Pre-emphasis = ON VODSEL = L Checker-board pattern (Figure 1) f = 40 MHz RL = 100 Pre-emphasis = OFF VODSEL = H Checker-board pattern (Figure 1) f = 40 MHz RL = 100 Pre-emphasis = ON VODSEL = H Checker-board pattern (Figure 1) f = 40 MHz TPWDNB = 0V (All other LVCMOS Inputs = 0V) 3 www.national.com DS99R105/DS99R106 Symbol DS99R105/DS99R106 Symbol IDDR IDDRZ Parameter Conditions Pin/Freq. Deserializer (Rx) Total Supply Current (includes load current) CL = 8 pF LVCMOS Output Checker-board pattern (Figure 2) f = 40 MHz Deserializer (Rx) Total Supply Current (includes load current) CL = 8 pF LVCMOS Output Random pattern f = 40 MHz Deserializer (Rx) Supply Current Power-down RPWDNB = 0V (All other LVCMOS Inputs = 0V, RIN+/ RIN- = 0V) Min Typ Max Units 95 mA 90 mA 1 50 A Min Typ Max Units 25 T Serializer Timing Requirements for TCLK Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions tTCP Transmit Clock Period tTCIH Transmit Clock High Time (Figure 5) tTCIL Transmit Clock Low Time tCLKT TCLK Input Transition Time (Figure 4) tJIT TCLK Input Jitter (Note 9) 333 ns 0.4T 0.5T 0.6T ns 0.4T 0.5T 0.6T ns 3 6 ns 33 ps (RMS) Serializer Switching Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions LVDS Low-to-High Transition Time tLHLT LVDS High-to-Low Transition Time tDIS DIN (23:0) Setup to TCLK tDIH DIN (23:0) Hold from TCLK tHZD DOUT HIGH to TRI-STATE Delay tLZD DOUT LOW to TRI-STATE Delay tZHD DOUT TRI-STATE to HIGH Delay tZLD DOUT TRI-STATE to LOW Delay tPLD Serializer PLL Lock Time RL = 100, (Figure 7) tSD Serializer Delay RL = 100, (Figure 8) VODSEL = L, TRFB = H TxOUT_E_O RL = 100, CL = 10 pF to GND (Note 8) TxOUT_Eye_Opening (respect to ideal) Min Typ RL = 100, (Figure 3) CL = 10 pF to GND VODSEL = L tLLHT Max Units 0.6 ns 0.6 ns 5 ns 5 ns RL = 100, CL = 10 pF to GND (Figure 6) (Note 5) 15 ns 15 ns 200 ns 200 ns 10 ms 3.5T + 2.85 3.5T + 10 ns RL = 100, (Figure 8) VODSEL = L, TRFB = L 3.5T + 2.85 3.5T + 10 ns 3-40 MHz (Figure 9) (Notes 9, 13) 0.68 UI (Note 10) Deserializer Switching Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter tRCP Receiver out Clock Period tRDC RCLK Duty Cycle tCLH LVCMOS Low-to-High Transition Time tCHL LVCMOS High-to-Low Transition Time www.national.com Conditions Pin/Freq. tRCP = tTCP (Note 8) RCLK RCLK CL = 8 pF (lumped load) (Figure 11) ROUT [23:0], LOCK, RCLK 4 Min Typ Max Units 25 T 333 ns 45 50 55 % 2.5 3.5 ns 2.5 3.5 ns Parameter Conditions Pin/Freq. ROUT [7:0] Typ Max Units tROS ROUT (7:0) Setup Data to RCLK (Group 1) tROH ROUT (7:0) Hold Data to RCLK (Group 1) tROS ROUT (15:8) Setup Data to RCLK (Group 2) tROH ROUT (15:8) Hold Data to RCLK (Group 2) tROS ROUT (23:16) Setup Data to RCLK (Group 3) tROH ROUT (23:16) Hold Data to RCLK (Group 3) tHZR HIGH to TRI-STATE Delay tLZR LOW to TRI-STATE Delay tZHR tZLR tDD Deserializer Delay (Figure 12) RCLK tDRDL Deserializer PLL Lock Time from Powerdown (Figure 14) (Notes 7, 8) 3 MHz 5 50 ms 40 MHz 5 50 ms Receiver INput TOLerance Left (Figure 16) (Notes 6, 8, 10) 3 MHz-40 MHz 0.25 UI RxIN_TOL_R Receiver INput TOLerance Right (Figure 16) (Notes 6, 8, 10) 3 MHz-40 MHz 0.25 UI RxIN_TOL_L (Figure 15) Min (Figure 15) ROUT [15:8], LOCK (Figure 15) ROUT [23:16] (Figure 13) (0.40)* (29/56)*tRCP tRCP ns (0.40)* (27/56)*tRCP tRCP ns (0.40)* tRCP 0.5*tRCP ns (0.40)* tRCP 0.5*tRCP ns (0.40)* (27/56)*tRCP tRCP ns (0.40)* (29/56)*tRCP tRCP ns ROUT [23:0], RCLK, LOCK 3 10 ns 3 10 ns TRI-STATE to HIGH Delay 3 10 ns TRI-STATE to LOW Delay 3 10 ns [4+(3/56)]T [4+(3/56)]T +5.9 +18.5 ns Note 1: "Absolute Maximum Ratings" indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions. Note 2: The Electrical Characteristics tables list guaranteed specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not guaranteed. Note 3: Typical values represent most likely parametric norms at VDD = 3.3V, Ta = +25 degC, and at the Recommended Operation Conditions at the time of product characterization and are not guaranteed. Note 4: Current into device pins is defined as positive. Current out of a device pin is defined as negative. Voltages are referenced to ground except VOD, VOD, VTH and VTL which are differential voltages. Note 5: When the Serializer output is tri-stated, the Deserializer will lose PLL lock. Resynchronization MUST occur before data transfer. Note 6: RxIN_TOL is a measure of how much phase noise (jitter) the deserializer can tolerate in the incoming data stream before bit errors occur. It is a measurement in reference with the ideal bit position, please see National's AN-1217 for detail. Note 7: The Deserializer PLL lock time (tDRDL) may vary depending on input data patterns and the number of transitions within the pattern. Note 8: Specification is guaranteed by characterization and is not tested in production. Note 9: tJIT (@BER of 10e-9) specifies the allowable jitter on TCLK. tJIT not included in TxOUT_E_O parameter. Note 10: UI - Unit Interval, equivalent to one ideal serialized data bit width. The UI scales with frequency. Note 11: Figures 1, 2, 8, 12, 14 show a falling edge data strobe (TCLK IN/RCLK OUT). Note 12: Figures 5, 15 show a rising edge data strobe (TCLK IN/RCLK OUT). Note 13: TxOUT_E_O is affected by pre-emphasis value. 5 www.national.com DS99R105/DS99R106 Symbol DS99R105/DS99R106 AC Timing Diagrams and Test Circuits 20208102 FIGURE 1. Serializer Input Checker-board Pattern 20208103 FIGURE 2. Deserializer Output Checker-board Pattern 20208104 FIGURE 3. Serializer LVDS Output Load and Transition Times 20208106 FIGURE 4. Serializer Input Clock Transition Times www.national.com 6 DS99R105/DS99R106 20208107 FIGURE 5. Serializer Setup/Hold Times 20208108 FIGURE 6. Serializer TRI-STATE Test Circuit and Delay 7 www.national.com DS99R105/DS99R106 20208109 FIGURE 7. Serializer PLL Lock Time, and TPWDNB TRI-STATE Delays 20208110 FIGURE 8. Serializer Delay 20208115 FIGURE 9. Transmitter Output Eye Opening (TxOUT_E_O) www.national.com 8 DS99R105/DS99R106 20208117 VOD = (DOUT+) - (DOUT -) Differential output signal is shown as (DOUT+) - (DOUT -), device in Data Transfer mode. FIGURE 10. Serializer VOD Diagram 20208105 FIGURE 11. Deserializer LVCMOS/LVTTL Output Load and Transition Times 20208111 FIGURE 12. Deserializer Delay 9 www.national.com DS99R105/DS99R106 20208113 Note: CL includes instrumentation and fixture capacitance within 6 cm of ROUT[23:0] FIGURE 13. Deserializer TRI-STATE Test Circuit and Timing 20208114 FIGURE 14. Deserializer PLL Lock Times and RPWDNB TRI-STATE Delay www.national.com 10 DS99R105/DS99R106 20208112 FIGURE 15. Deserializer Setup and Hold Times 20208116 RxIN_TOL_L is the ideal noise margin on the left of the figure, with respect to ideal. RxIN_TOL_R is the ideal noise margin on the right of the figure, with respect to ideal. FIGURE 16. Receiver Input Tolerance (RxIN_TOL) and Sampling Window 11 www.national.com DS99R105/DS99R106 DS99R105 Serializer Pin Descriptions Pin # Pin Name I/O Description LVCMOS PARALLEL INTERFACE PINS 4-1, DIN[23:0] 48-44, 41-32, 29-25 LVCMOS_I Transmitter Parallel Interface Data Inputs Pins. Tie LOW if unused, do not float. 10 LVCMOS_I Transmitter Parallel Interface Clock Input Pin. Strobe edge set by TRFB configuration pin. TCLK CONTROL AND CONFIGURATION PINS 9 TPWDNB LVCMOS_I Transmitter Power Down Bar TPWDNB = H; Transmitter is Enabled and ON TPWDNB = L; Transmitter is in power down mode (Sleep), LVDS Driver DOUT (+/-) Outputs are in TRI-STATE stand-by mode, PLL is shutdown to minimize power consumption. 18 DEN LVCMOS_I Transmitter Data Enable DEN = H; LVDS Driver Outputs are Enabled (ON). DEN = L; LVDS Driver Outputs are Disabled (OFF), Transmitter LVDS Driver DOUT (+/-) Outputs are in TRI-STATE, PLL still operational and locked to TCLK. 23 PRE LVCMOS_I PRE-emphasis select pin. PRE = L; Pre-emphasis is enabled PRE = H; Pre-emphasis is disabled 11 TRFB LVCMOS_I Transmitter Clock Edge Select Pin TRFB = H; Parallel Interface Data is strobed on the Rising Clock Edge TRFB = L; Parallel Interface Data is strobed on the Falling Clock Edge 12 VODSEL LVCMOS_I VOD Level Select VODSEL = L; LVDS Driver Output is 400 mV (RL = 100) VODSEL = H; LVDS Driver Output is 750 mV (RL = 100) For normal applications, set this pin LOW. For long cable applications where a larger VOD is required, set this pin HIGH. 5 DCAOFF LVCMOS_I RESERVED - This pin MUST be tied LOW. 8 DCBOFF LVCMOS_I RESERVED - This pin MUST be tied LOW. 13 RESRVD LVCMOS_I RESERVED - This pin MUST be tied LOW. LVDS SERIAL INTERFACE PINS 20 DOUT+ LVDS_O Transmitter LVDS True (+) Output. This output is intended to be loaded with a 100 ohm load to the DOUT+ pin. The interconnect should be AC Coupled to this pin with a 100 nF capacitor. 19 DOUT- LVDS_O Transmitter LVDS Inverted (-) Output This output is intended to be loaded with a 100 ohm load to the DOUT- pin. The interconnect should be AC Coupled to this pin with a 100 nF capacitor. POWER / GROUND PINS 22 VDDDR VDD Analog Voltage Supply, LVDS Output Power 21 VSSDR GND Analog Ground, LVDS Output Ground 16 VDDPT0 VDD Analog Voltage supply, VCO Power 17 VSSPT0 GND Analog Ground, VCO Ground 14 VDDPT1 VDD Analog Voltage supply, PLL Power 15 VSSPT1 GND Analog Ground, PLL Ground 30 VDDT VDD Digital Voltage supply, Tx Serializer Power 31 VSST GND Digital Ground, Tx Serializer Ground 7 VDDL VDD Digital Voltage supply, Tx Logic Power 6 VSSL GND Digital Ground, Tx Logic Ground 42 VDDIT VDD Digital Voltage supply, Tx Input Power 43 VSSIT GND Digital Ground, Tx Input Ground 24 VSS GND ESD Ground www.national.com 12 DS99R105/DS99R106 DS99R105 Pin Diagram Serializer - DS99R105 20208119 TOP VIEW 13 www.national.com DS99R105/DS99R106 DS99R106 Deserializer Pin Descriptions Pin # Pin Name I/O Description LVCMOS PARALLEL INTERFACE PINS 25-28, ROUT[7:0] 31-34 LVCMOS_O Receiver Parallel Interface Data Outputs - Group 1 13-16, ROUT[15:8] 21-24 LVCMOS_O Receiver Parallel Interface Data Outputs - Group 2 3-6, 9-12 ROUT[23:16] LVCMOS_O Receiver Parallel Interface Data Outputs - Group 3 18 RCLK Parallel Interface Clock Output Pin. Strobe edge set by RRFB configuration pin. LVCMOS_O CONTROL AND CONFIGURATION PINS 43 RRFB LVCMOS_I Receiver Clock Edge Select Pin RRFB = H; ROUT LVCMOS Outputs strobed on the Rising Clock Edge. RRFB = L; ROUT LVCMOS Outputs strobed on the Falling Clock Edge. 48 REN LVCMOS_I Receiver Data Enable REN = H; ROUT[23-0] and RCLK are Enabled (ON). REN = L; ROUT[23-0] and RCLK are Disabled (OFF), Receiver ROUT[23-0] and RCLK Outputs are in TRI-STATE, PLL still operational and locked to TCLK. 1 RPWDNB LVCMOS_I Receiver Data Enable REN = H; ROUT[23-0] and RCLK are Enabled (ON). REN = L; ROUT[23-0] and RCLK are Disabled (OFF), Receiver ROUT[23-0] and RCLK Outputs are in TRI-STATE, PLL still operational and locked to TCLK. 17 LOCK LVCMOS_O LOCK indicates the status of the receiver PLL LOCK = H; receiver PLL is locked LOCK = L; receiver PLL is unlocked, ROUT[23-0] and RCLK are TRI-STATED 2 RESRVD LVCMOS_I RESERVED - This pin MUST be tied LOW. LVDS SERIAL INTERFACE PINS 41 RIN+ LVDS_I Receiver LVDS True (+) Input This input is intended to be terminated with a 100 ohm load to the RIN+ pin. The interconnect should be AC Coupled to this pin with a 100 nF capacitor. 42 RIN- LVDS_I Receiver LVDS Inverted (-) Input This input is intended to be terminated with a 100 ohm load to the RIN- pin. The interconnect should be AC Coupled to this pin with a 100 nF capacitor. POWER / GROUND PINS 39 VDDIR VDD Analog LVDS Voltage supply, Power 40 VSSIR GND Analog LVDS Ground 47 VDDPR0 VDD Analog Voltage supply, PLL Power 46 VSSPR0 GND Analog Ground, PLL Ground 45 VDDPR1 VDD Analog Voltage supply, PLL VCO Power 44 VSSPR1 GND Analog Ground, PLL VCO Ground 37 VDDR1 VDD Digital Voltage supply, Logic Power 38 VSSR1 GND Digital Ground, Logic Ground 36 VDDR0 VDD Digital Voltage supply, Logic Power 35 VSSR0 GND Digital Ground, Logic Ground 30 VDDOR1 VDD Digital Voltage supply, LVCMOS Output Power 29 VSSOR1 GND Digital Ground, LVCMOS Output Ground 20 VDDOR2 VDD Digital Voltage supply, LVCMOS Output Power 19 VSSOR2 GND Digital Ground, LVCMOS Output Ground 7 VDDOR3 VDD Digital Voltage supply, LVCMOS Output Power 8 VSSOR3 GND Digital Ground, LVCMOS Output Ground www.national.com 14 DS99R105/DS99R106 DS99R106 Pin Diagram Deserializer - DS99R106 20208120 TOP VIEW 15 www.national.com DS99R105/DS99R106 DATA TRANSFER After lock is established, the Serializer inputs DIN0-DIN23 are used to input data to the Serializer. Data is clocked into the Serializer by the TCLK input. The edge of TCLK used to strobe the data is selectable via the TRFB pin. TRFB high selects the rising edge for clocking data and low selects the falling edge. The Serializer outputs (DOUT) are intended to drive point-to-point connections or limited multi-point applications. CLK1, CLK0, DCA, DCB are four overhead bits transmitted along the single LVDS serial data stream. The CLK1 bit is always high and the CLK0 bit is always low. The CLK1 and CLK0 bits function as the embedded clock bits in the serial stream. DCB functions as the DC Balance control bit. It does not require any pre-coding of data on transmit side. The DC Balance bit is used to minimize the short and long-term DC bias on the signal lines. This bit operates by selectively sending the data either unmodified or inverted. The DCA bit is used to validate data integrity in the embedded data stream. Both DCA and DCB coding schemes are integrated and automatically performed within Serializer and Deserializer. The chipset supports clock frequency ranges of 3 MHz to 40 MHz. Every clock cycle, 24 databits are sent along with 4 additional overhead control bits. Thus the line rate is 1.12 Gbps maximum (84 Mbps minimum). The link is extremely efficient at 86% (24/28). Twenty five (24 data + 1 clock) plus associated ground signals are reduced to only 1 single LVDS pair providing a compression ratio of better then 25 to 1. Serialized data and clock/control bits (24+4 bits) are transmitted from the serial data output (DOUT) at 28 times the TCLK frequency. For example, if TCLK is , the serial rate is 40 x 28 = 1.12 Giga bits per second. Since only 24 bits are from input data, the serial "payload" rate is 24 times the TCLK frequency. For instance, if TCLK = 40 MHz, the payload data rate is 40 x 24 = 960 Mbps. TCLK is provided by the data source and must be in the range of 3 MHz to 40 MHz nominal. The Serializer outputs (DOUT) can drive a point-to-point connection as shown in Figure 17. The outputs transmit data when the enable pin (DEN) is high and TPWDNB is high. The DEN pin may be used to TRI-STATE the outputs when driven low. When the Deserializer channel attains lock to the input from a Serializer, it drives its LOCK pin high and synchronously delivers valid data and recovered clock on the output. The Deserializer locks onto the embedded clock, uses it to generate multiple internal data strobes, and then drives the recovered clock to the RCLK pin. The recovered clock (RCLK output pin) is synchronous to the data on the ROUT[23:0] pins. While LOCK is high, data on ROUT[23:0] is valid. Otherwise, ROUT[23:0] is invalid. The polarity of the RCLK edge is controlled by the RRFB input. ROUT(0-23), LOCK and RCLK outputs will each drive a maximum of 8 pF load with a 40 MHz clock. REN controls TRI-STATE for ROUTn and the RCLK pin on the Deserializer. Functional Description The DS99R105 Serializer and DS99R106 Deserializer chipset is an easy-to-use transmitter and receiver pair that sends 24-bits of parallel LVCMOS data over a single serial LVDS link from 72 Mbps to 960 Mbps throughput. The DS99R105 transforms a 24-bit wide parallel LVCMOS data into a single high speed LVDS serial data stream with embedded clock. The DS99R106 receives the LVDS serial data stream and converts it back into a 24-bit wide parallel data and recovered clock. The 24-bit Serializer/Deserializer chipset is designed to transmit data over shielded twisted pair (STP) at clock speeds from 3 MHz to 40 MHz. The Deserializer can attain lock to a data stream without the use of a separate reference clock source. The Deserializer synchronizes to the Serializer regardless of data pattern, delivering true automatic "plug and lock" performance. The Deserializer recovers the clock and data by extracting the embedded clock information and validating data integrity from the incoming data stream and then deserializes the data. The Deserializer monitors the incoming clock information, determines lock status, and asserts the LOCK output high when lock occurs. Each has a power down control to enable efficient operation in various applications. INITIALIZATION AND LOCKING MECHANISM Initialization of the DS99R105 and DS99R106 must be established before each device sends or receives data. Initialization refers to synchronizing the Serializer's and Deserializer's PLL's together. After the Serializers locks to the input clock source, the Deserializer synchronizes to the Serializers as the second and final initialization step. Step 1: When VDD is applied to both Serializer and/or Deserializer, the respective outputs are held in TRI-STATE and internal circuitry is disabled by on-chip power-on circuitry. When VDD reaches VDD OK (2.2V) the PLL in Serializer begins locking to a clock input. For the Serializer, the local clock is the transmit clock, TCLK. The Serializer outputs are held in TRI-STATE while the PLL locks to the TCLK. After locking to TCLK, the Serializer block is now ready to send data patterns. The Deserializer output will remain in TRI-STATE while its PLL locks to the embedded clock information in serial data stream. Also, the Deserializer LOCK output will remain low until its PLL locks to incoming data and sync-pattern on the RIN pins. Step 2: The Deserializer PLL acquires lock to a data stream without requiring the Serializer to send special patterns. The Serializer that is generating the stream to the Deserializer will automatically send random (non-repetitive) data patterns during this step of the Initialization State. The Deserializer will lock onto embedded clock within the specified amount of time. An embedded clock and data recovery (CDR) circuit locks to the incoming bit stream to recover the high-speed receive bit clock and re-time incoming data. The CDR circuit expects a coded input bit stream. In order for the Deserializer to lock to a random data stream from the Serializer, it performs a series of operations to identify the rising clock edge and validates data integrity, then locks to it. Because this locking procedure is independent on the data pattern, total random locking duration may vary. At the point when the Deserializer's CDR locks to the embedded clock, the LOCK pin goes high and valid RCLK/data appears on the outputs. Note that the LOCK signal is synchronous to valid data appearing on the outputs. The Deserializer's LOCK pin is a convenient way to ensure data integrity is achieved on receiver side. www.national.com RESYNCHRONIZATION If the Deserializer loses lock, it will automatically try to re-establish lock. For example, if the embedded clock edge is not detected one time in succession, the PLL loses lock and the LOCK pin is driven low. The Deserializer then enters the operating mode where it tries to lock to a random data stream. It looks for the embedded clock edge, identifies it and then proceeds through the locking process. The logic state of the LOCK signal indicates whether the data on ROUT is valid; when it is high, the data is valid. The system 16 package parasitics. The most common used capacitor value for the interface is 100 nF (0.1 uF) capacitor. A termination resistor across DOUT is also required for proper operation to be obtained. The termination resistor should be equal to the differential impedance of the media being driven. This should be in the range of 90 to 132 Ohms. 100 Ohms is a typical value common used with standard 100 Ohm transmission media. This resistor is required for control of reflections and also to complete the current loop. It should be placed as close to the Serializer DOUT outputs to minimize the stub length from the pins. To match with the deferential impedance on the transmission line, the LVDS I/O are terminated with 100 ohm resistors on Serializer DOUT outputs pins. POWERDOWN The Powerdown state is a low power sleep mode that the Serializer and Deserializer may use to reduce power when no data is being transferred. The TPWDNB and RPWDNB are used to set each device into power down mode, which reduces supply current to the A range. The Serializer enters powerdown when the TPWDNB pin is driven low. In powerdown, the PLL stops and the outputs go into TRI-STATE, disabling load current and reducing supply. To exit Powerdown, TPWDNB must be driven high. When the Serializer exits Powerdown, its PLL must lock to TCLK before it is ready for the Initialization state. The system must then allow time for Initialization before data transfer can begin. The Deserializer enters powerdown mode when RPWDNB is driven low. In powerdown mode, the PLL stops and the outputs enter TRISTATE. To bring the Deserializer block out of the powerdown state, the system drives RPWDNB high. Both the Serializer and Deserializer must reinitialize and relock before data can be transferred. The Deserializer will initialize and assert LOCK high when it is locked to the encoded clock. PROGRESSIVE TURN-ON (PTO) Deserializer ROUT[23:0] outputs are grouped into three groups of eight, with each group switching about 0.5UI apart in phase to reduce EMI, simultaneous switching noise, and system ground bounce. Applications Information USING THE DS99R105 AND DS99R106 The DS99R105/DS99R106 Serializer/Deserializer (SERDES) pair sends 24 bits of parallel LVCMOS data over a serial LVDS link up to 960 Mbps. Serialization of the input data is accomplished using an on-board PLL at the Serializer which embeds clock with the data. The Deserializer extracts the clock/control information from the incoming data stream and deserializes the data. The Deserializer monitors the incoming clockl information to determine lock status and will indicate lock by asserting the LOCK output high. TRI-STATE For the Serializer, TRI-STATE is entered when the DEN or TPWDNB pin is driven low. This will TRI-STATE both driver output pins (DOUT+ and DOUT-). When DEN is driven high, the serializer will return to the previous state as long as all other control pins remain static (TPWDNB, TRFB). When you drive the REN or RPWDNB pin low, the Deserializer enters TRI-STATE. Consequently, the receiver output pins (ROUT0-ROUT23) and RCLK will enter TRI-STATE. The LOCK output remains active, reflecting the state of the PLL. The Deserializer input pins are high impedance during receiver powerdown (RPWDNB low) and power-off (VDD = 0V). POWER CONSIDERATIONS An all CMOS design of the Serializer and Deserializer makes them inherently low power devices. Additionally, the constant current source nature of the LVDS outputs minimize the slope of the speed vs. IDD curve of CMOS designs. PRE-EMPHASIS The DS99R105 features a Pre-Emphasis mode used to compensate for long or lossy transmission media. Cable drive is enhanced with a user selectable Pre-Emphasis feature that provides additional output current during transitions to counteract cable loading effects. The transmission distance will be limited by the loss characteristics and quality of the media. Pre-Emphasis adds extra current during LVDS logic transition to reduce the cable loading effects and increase driving distance. In addition, Pre-Emphasis helps provide faster transitions, increased eye openings, and improved signal integrity. The ability of the DS99R105 to use the Pre-Emphasis feature will extend the transmission distance in most cases. NOISE MARGIN The Deserializer noise margin is the amount of input jitter (phase noise) that the Deserializer can tolerate and still reliably recover data. Various environmental and systematic factors include: Serializer: TCLK jitter, VDD noise (noise bandwidth and outof-band noise) Media: ISI, VCM noise Deserializer: VDD noise For a graphical representation of noise margin, please see Figure 16. TRANSMISSION MEDIA The Serializer and Deserializer can be used in point-to-point configuration, through a PCB trace, or through twisted pair cable. In a point-to-point configuration, the transmission media needs be terminated at both ends of the transmitter and receiver pair. Interconnect for LVDS typically has a differential impedance of 100 Ohms. Use cables and connectors that have matched differential impedance to minimize impedance discontinuities. In most applications that involve cables, the transmission distance will be determined on data rates involved, acceptable bit error rate and transmission medium. AC-COUPLING AND TERMINATION The DS99R105 and DS99R106 supports AC-coupled interconnects through integrated DC balanced encoding/decoding scheme. To use AC coupled connection between the Serializer and Deserializer, insert external AC coupling capacitors in series in the LVDS signal path as illustrated in Figure 17. The Deserializer input stage is designed for AC-coupling by providing a built-in AC bias network which sets the internal VCM to +1.2V. With AC signal coupling, capacitors provide the ac-coupling path to the signal input. For the high-speed LVDS transmissions, the smallest available package should be used for the AC coupling capacitor. This will help minimize degradation of signal quality due to 17 www.national.com DS99R105/DS99R106 must monitor the LOCK pin to determine whether data on the ROUT is valid. DS99R105/DS99R106 practice to use two vias from power and ground pins to the planes, reducing the impedance at high frequency. Some devices provide separate power and ground pins for different portions of the circuit. This is done to isolate switching noise effects between different sections of the circuit. Separate planes on the PCB are typically not required. Pin Description tables typically provide guidance on which circuit blocks are connected to which power pin pairs. In some cases, an external filter many be used to provide clean power to sensitive circuits such as PLLs. Use at least a four layer board with a power and ground plane. Locate LVCMOS (LVTTL) signals away from the LVDS lines to prevent coupling from the LVCMOS lines to the LVDS lines. Closely-coupled differential lines of 100 Ohms are typically recommended for LVDS interconnect. The closely coupled lines help to ensure that coupled noise will appear as common-mode and thus is rejected by the receivers. The tightly coupled lines will also radiate less. Termination of the LVDS interconnect is required. For pointto-point applications, termination should be located at both ends of the devices. Nominal value is 100 Ohms to match the line's differential impedance. Place the resistor as close to the transmitter DOUT outputs and receiver RIN inputs as possible to minimize the resulting stub between the termination resistor and device. LIVE LINK INSERTION The Serializer and Deserializer devices support live pluggable applications. The "Hot Inserted" operation on the serial interface does not disrupt communication data on the active data lines. The automatic receiver lock to random data "plug & go" live insertion capability allows the DS99R106 to attain lock to the active data stream during a live insertion event. PCB LAYOUT AND POWER SYSTEM CONSIDERATIONS Circuit board layout and stack-up for the LVDS SERDES devices should be designed to provide low-noise power feed to the device. Good layout practice will also separate high frequency or high-level inputs and outputs to minimize unwanted stray noise pickup, feedback and interference. Power system performance may be greatly improved by using thin dielectrics (2 to 4 mils) for power / ground sandwiches. This arrangement provides plane capacitance for the PCB power system with low-inductance parasitics, which has proven especially effective at high frequencies, and makes the value and placement of external bypass capacitors less critical. External bypass capacitors should include both RF ceramic and tantalum electrolytic types. RF capacitors may use values in the range of 0.01 uF to 0.1 uF. Tantalum capacitors may be in the 2.2 uF to 10 uF range. Voltage rating of the tantalum capacitors should be at least 5X the power supply voltage being used. Surface mount capacitors are recommended due to their smaller parasitics. When using multiple capacitors per supply pin, locate the smaller value closer to the pin. A large bulk capacitor is recommend at the point of power entry. This is typically in the 50uF to 100uF range and will smooth low frequency switching noise. It is recommended to connect power and ground pins directly to the power and ground planes with bypass capacitors connected to the plane with via on both ends of the capacitor. Connecting power or ground pins to an external bypass capacitor will increase the inductance of the path. A small body size X7R chip capacitor, such as 0603, is recommended for external bypass. Its small body size reduces the parasitic inductance of the capacitor. The user must pay attention to the resonance frequency of these external bypass capacitors, usually in the range of 20-30 MHz range. To provide effective bypassing, multiple capacitors are often used to achieve low impedance between the supply rails over the frequency of interest. At high frequency, it is also a common LVDS INTERCONNECT GUIDELINES See AN-1108 and AN-905 for full details. * Use 100 coupled differential pairs * Use the S/2S/3S rule in spacings --S = space between the pair --2S = space between pairs --3S = space to LVCMOS/LVTTL signal * Minimize the number of VIA * Use differential connectors when operating above 500Mbps line speed * Maintain balance of the traces * Minimize skew within the pair * Terminate as close to the TX outputs and RX inputs as possible Additional general guidance can be found in the LVDS Owner's Manual - available in PDF format from the National web site at: www.national.com/lvds 20208118 FIGURE 17. AC Coupled Application www.national.com 18 DS99R105/DS99R106 20208121 FIGURE 18. DS99R105 Typical Application Connection 19 www.national.com DS99R105/DS99R106 20208122 FIGURE 19. DS99R106 Typical Application Connection www.national.com 20 DS99R105/DS99R106 Truth Tables TABLE 1. DS99R105 Serializer Truth Table TPWDNB (Pin 9) DEN (Pin 18) Tx PLL Status (Internal) LVDS Outputs (Pins 19 and 20) L X X Hi Z H L X Hi Z H H Not Locked Hi Z H H Locked Serialized Data with Embedded Clock TABLE 2. DS99R106 Deserializer Truth Table RPWDNB (Pin 1) REN (Pin 48) Rx PLL Status (Internal) ROUTn and RCLK (See Pin Diagram) LOCK (Pin 17) L X X Hi Z Hi Z H L X Hi Z L = PLL Unocked; H = PLL Locked H H Not Locked Hi Z L H H Locked Data and RCLK Active H 21 www.national.com DS99R105/DS99R106 Physical Dimensions inches (millimeters) unless otherwise noted Dimensions show in millimeters only Ordering Information NSID Package Type Package ID DS99R105VS 48 Lead TQFP style, 7.0 X 7.0 X 1.0 mm, 0.5 mm pitch VBC48A DS99R105VSX 48 Lead TQFP style, 7.0 X 7.0 X 1.0 mm, 0.5 mm pitch, 1000 std reel VBC48A DS99R106VS 48 Lead TQFP style, 7.0 X 7.0 X 1.0 mm, 0.5 mm pitch VBC48A DS99R106VSX 48 Lead TQFP style, 7.0 X 7.0 X 1.0 mm, 0.5 mm pitch, 1000 std reel VBC48A www.national.com 22 DS99R105/DS99R106 Physical Dimensions inches (millimeters) unless otherwise noted Dimensions show in millimeters only Ordering Information NSID Package Type Package ID DS99R105SQ 48 Lead LLP style, 7.0 X 7.0 X 0.8 mm, 0.5 mm pitch SQA48D DS99R105SQX 48 Lead LLP style, 7.0 X 7.0 X 0.8 mm, 0.5 mm pitch, 1000 std reel SQA48D DS99R106SQ 48 Lead LLP style, 7.0 X 7.0 X 0.8 mm, 0.5 mm pitch SQA48D DS99R106SQX 48 Lead LLP style, 7.0 X 7.0 X 0.8 mm, 0.5 mm pitch, 1000 std reel SQA48D 23 www.national.com DS99R105/DS99R106 3-40MHz DC-Balanced 24-Bit LVDS Serializer and Deserializer Notes THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2007 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530-85-86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +49 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560