LP3883
LP3883 3A Fast-Response Ultra Low Dropout Linear Regulators
Literature Number: SNVS223E
LP3883
3A Fast-Response Ultra Low Dropout Linear Regulators
General Description
The LP3883 is a high-current, fast-response regulator which
can maintain output voltage regulation with minimum input to
output voltage drop. Fabricated on a CMOS process, the
device operates from two input voltages: Vbias provides
voltage to drive the gate of the N-MOS power transistor,
while Vin is the input voltage which supplies power to the
load. The use of an external bias rail allows the part to
operate from ultra low Vin voltages. Unlike bipolar regula-
tors, the CMOS architecture consumes extremely low quies-
cent current at any output load current. The use of an
N-MOS power transistor results in wide bandwidth, yet mini-
mum external capacitance is required to maintain loop sta-
bility.
The fast transient response of these devices makes them
suitable for use in powering DSP, Microcontroller Core volt-
ages and Switch Mode Power Supply post regulators. The
parts are available in TO-220 and TO-263 packages.
Dropout Voltage: 210 mV (typ) @3A load current.
Ground Pin Current: 3 mA (typ) at full load.
Shutdown Current: 60 nA (typ) when S/D pin is low.
Precision Output Voltage: 1.5% room temperature accu-
racy.
Features
nUltra low dropout voltage (210 mV @3A typ)
nLow ground pin current
nLoad regulation of 0.04%/A
n60 nA typical quiescent current in shutdown
n1.5% output accuracy (25˚C)
nTO-220, TO-263 packages
nOver temperature/over current protection
n−40˚C to +125˚C junction temperature range
Applications
nDSP Power Supplies
nServer Core and I/O Supplies
nLinear Power Supplies for PC Add-in-Cards
nSet-Top Box Power Supplies
nMicroprocessor Power Supplies
nHigh Efficiency Linear Power Supplies
nSMPS Post-Regulators
Typical Application Circuit
20062401
At least 4.7 µF of input and output capacitance is required for stability.
February 2006
LP3883 3A Fast-Response Ultra Low Dropout Linear Regulators
© 2006 National Semiconductor Corporation DS200624 www.national.com
Connection Diagrams
20062402
TO-220, Top View
20062403
TO-263, Top View
Ordering Information
Order Number Package Type Package Drawing Supplied As
LP3883ES-1.2 TO263-5 TS5B Rail
LP3883ESX-1.2 TO263-5 TS5B Tape and Reel
LP3883ET-1.2 TO220-5 T05D Rail
LP3883ES-1.5 TO263-5 TS5B Rail
LP3883ESX-1.5 TO263-5 TS5B Tape and Reel
LP3883ET-1.5 TO220-5 T05D Rail
LP3883ES-1.8 TO263-5 TS5B Rail
LP3883ESX-1.8 TO263-5 TS5B Tape and Reel
LP3883ET-1.8 TO220-5 T05D Rail
Block Diagram
20062424
LP3883
www.national.com 2
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Storage Temperature Range −65˚C to +150˚C
Lead Temp. (Soldering, 5 seconds) 260˚C
ESD Rating
Human Body Model (Note 3)
Machine Model (Note 10)
2kV
200V
Power Dissipation (Note 2) Internally Limited
V
IN
Supply Voltage (Survival) −0.3V to +6V
V
BIAS
Supply Voltage (Survival) −0.3V to +7V
Shutdown Input Voltage (Survival) −0.3V to +7V
I
OUT
(Survival) Internally Limited
Output Voltage (Survival) −0.3V to +6V
Junction Temperature −40˚C to +150˚C
Operating Ratings
V
IN
Supply Voltage (V
OUT
+V
DO
) to 5.5V
Shutdown Input Voltage 0 to +6V
I
OUT
3A
Operating Junction
Temperature Range
−40˚C to +125˚C
V
BIAS
Supply Voltage 4.5V to 6V
Electrical Characteristics Limits in standard typeface are for T
J
= 25˚C, and limits in boldface type apply
over the full operating temperature range. Unless otherwise specified: V
IN
=V
O
(NOM) + 1V, V
BIAS
= 4.5V, I
L
= 10 mA, C
IN
=
C
OUT
= 4.7 µF, V
S/D
=V
BIAS
.
Symbol Parameter Conditions Typical
(Note 4)
MIN
(Note 5)
MAX
(Note 5) Units
V
O
Output Voltage Tolerance 10 mA <I
L
<3A
V
O
(NOM) + 1V ≤V
IN
≤5.5V
4.5V ≤V
BIAS
≤6V
1.216
1.198
1.186
1.234
1.246
V1.5
1.478
1.455
1.522
1.545
1.8
1.773
1.746
1.827
1.854
∆V
O
/∆V
IN
Output Voltage Line Regulation
(Note 7)
V
O
(NOM) + 1V ≤V
IN
≤5.5V 0.01 %/V
∆V
O
/∆I
L
Output Voltage Load Regulation
(Note 8)
10 mA <I
L
<3A 0.04
0.06 %/A
V
DO
Dropout Voltage (Note 9) I
L
=3A 210 270
420 mV
I
Q
(V
IN
) Quiescent Current Drawn from
V
IN
Supply
10 mA <I
L
<3A 37
8mA
V
S/D
≤0.3V 0.03 1
30 µA
I
Q
(V
BIAS
) Quiescent Current Drawn from
V
BIAS
Supply
10 mA <I
L
<3A 12
3mA
V
S/D
≤0.3V 0.03 1
30 µA
I
SC
Short-Circuit Current V
OUT
=0V 6 A
Shutdown Input
V
SDT
Output Turn-off Threshold Output = ON 0.7 1.3 V
Output = OFF 0.7 0.3
Td (OFF) Turn-OFF Delay R
LOAD
XC
OUT
<< Td (OFF) 20 µs
Td (ON) Turn-ON Delay R
LOAD
XC
OUT
<< Td (ON) 15
I
S/D
S/D Input Current V
S/D
=1.3V 1 µA
V
S/D
≤0.3V −1
LP3883
www.national.com3
Electrical Characteristics Limits in standard typeface are for T
J
= 25˚C, and limits in boldface type apply
over the full operating temperature range. Unless otherwise specified: V
IN
=V
O
(NOM) + 1V, V
BIAS
= 4.5V, I
L
= 10 mA, C
IN
=
COUT = 4.7 µF, V
S/D
=V
BIAS
. (Continued)
Symbol Parameter Conditions Typical
(Note 4)
MIN
(Note 5)
MAX
(Note 5) Units
AC Parameters
PSRR (V
IN
) Ripple Rejection for V
IN
Input
Voltage
V
IN
=V
OUT
+1V, f = 120 Hz 80
dB
V
IN
=V
OUT
+ 1V, f = 1 kHz 65
PSRR
(V
BIAS
)
Ripple Rejection for V
BIAS
Voltage
V
BIAS
=V
OUT
+ 3V, f = 120 Hz 70
V
BIAS
=V
OUT
+ 3V, f = 1 kHz 65
Output Noise Density f = 120 Hz 1 µV/root−Hz
e
n
Output Noise Voltage
V
OUT
= 1.8V
BW = 10 Hz − 100 kHz 150 µV (rms)
BW = 300 Hz − 300 kHz 90
Note 1: Absolute maximum ratings indicate limits beyond which damage to the component may occur. Operating ratings indicate conditions for which the device
is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications, see Electrical Characteristics. Specifications do not
apply when operating the device outside of its rated operating conditions.
Note 2: At elevated temperatures, device power dissipation must be derated based on package thermal resistance and heatsink thermal values. θJ-A for TO-220
devices is 65˚C/W if no heatsink is used. If the TO-220 device is attached to a heatsink, a θJ-S value of 4˚C/W can be assumed. θJ-A for TO-263 devices is
approximately 40˚C/W if soldered down to a copper plane which is at least 1.5 square inches in area. If power dissipation causes the junction temperature to exceed
specified limits, the device will go into thermal shutdown.
Note 3: The human body model is a 100 pF capacitor discharged through a 1.5k resistor into each pin.
Note 4: Typical numbers represent the most likely parametric norm for 25˚C operation.
Note 5: Limits are guaranteed through testing, statistical correlation, or design.
Note 6: If used in a dual-supply system where the regulator load is returned to a negative supply, the output pin must be diode clamped to ground.
Note 7: Output voltage line regulation is defined as the change in output voltage from nominal value resulting from a change in input voltage.
Note 8: Output voltage load regulation is defined as the change in output voltage from nominal value as the load current increases from no load to full load.
Note 9: Dropout voltage is defined as the minimum input to output differential required to maintain the output with 2% of nominal value.
Note 10: The machine model is a 220 pF capacitor discharged directly into each pin. The machine model ESD rating of pin 5 is 100V.
LP3883
www.national.com 4
Typical Performance Characteristics
Unless otherwise specified: T
A
= 25˚C, C
OUT
= 4.7µF, Cin
= 4.7µF, S/D pin is tied to V
BIAS
,V
IN
= 2.2V, V
OUT
= 1.8V.
Dropout vs I
L
I
GND
vs VSD
20062404 20062405
V
OUT
vs Temperature DC Load Regulation
20062406 20062407
Line Regulation vs V
IN
Line Regulation vs V
BIAS
20062408 20062409
LP3883
www.national.com5
Typical Performance Characteristics Unless otherwise specified: T
A
= 25˚C, C
OUT
= 4.7µF, Cin =
4.7µF, S/D pin is tied to V
BIAS
,V
IN
= 2.2V, V
OUT
= 1.8V. (Continued)
I
BIAS
vs I
L
I
BIAS
vs V
BIAS
20062410 20062411
I
GND
vs VSD Noise Measurement
20062412 20062414
V
OUT
Startup Waveform V
OUT
Startup Waveform
20062415 20062416
LP3883
www.national.com 6
Typical Performance Characteristics Unless otherwise specified: T
A
= 25˚C, C
OUT
= 4.7µF, Cin =
4.7µF, S/D pin is tied to V
BIAS
,V
IN
= 2.2V, V
OUT
= 1.8V. (Continued)
V
OUT
Startup Waveform Line Regulation vs V
BIAS
20062417
20062418
Line Regulation vs V
BIAS
V
IN
PSRR
20062419
20062420
V
IN
PSRR V
BIAS
PSRR
20062423 20062422
LP3883
www.national.com7
Typical Performance Characteristics Unless otherwise specified: T
A
= 25˚C, C
OUT
= 4.7µF, Cin =
4.7µF, S/D pin is tied to V
BIAS
,V
IN
= 2.2V, V
OUT
= 1.8V. (Continued)
Load Transient Response
(Both Oscon 10µF/3A)
Load Transient Response
(Both Oscon 100µF/3A)
20062440 20062441
Load Transient Response
(Both POSCAP 100µF/3A)
Load Transient Response
(SANYO 150µF/3A)
20062442
20062443
Load Transient Response
(Tantalum 10µF/3A)
Load Transient Response
(Tantalum 100µF/3A)
20062444 20062445
LP3883
www.national.com 8
Typical Performance Characteristics Unless otherwise specified: T
A
= 25˚C, C
OUT
= 4.7µF, Cin =
4.7µF, S/D pin is tied to V
BIAS
,V
IN
= 2.2V, V
OUT
= 1.8V. (Continued)
Load Transient Response
(Both Oscon 10µF/1A)
Load Transient Response
(Both Oscon 100µF/1A)
20062446 20062447
Load Transient Response
(Both POSCAP 100µF/1A)
Load Transient Response
(SANYO 150µF/1A)
20062448 20062451
Load Transient Response
(Tantalum 10µF/1A)
Load Transient Response
(Tantalum 100µF/1A)
20062449 20062450
LP3883
www.national.com9
Application Hints
EXTERNAL CAPACITORS
To assure regulator stability, input and output capacitors are
required as shown in the Typical Application Circuit.
OUTPUT CAPACITOR
At least 4.7µF of output capacitance is required for stability
(the amount of capacitance can be increased without limit).
The output capacitor must be located less than 1 cm from
the output pin of the IC and returned to a clean analog
ground. The ESR (equivalent series resistance) of the output
capacitor must be within the "stable" range as shown in the
graph below over the full operating temperature range for
stable operation.
20062431
Minimum ESR vs Output Load Current
Tantalum capacitors are recommended for the output as
their ESR is ideally suited to the part’s requirements and the
ESR is very stable over temperature. Aluminum electrolytics
are not recommended because their ESR increases very
rapidly at temperatures below 10C. Aluminum caps can only
be used in applications where lower temperature operation
is not required.
A second problem with Al caps is that many have ESR’s
which are only specified at low frequencies. The typical loop
bandwidth of a linear regulator is a few hundred kHz to
several MHz. If an Al cap is used for the output cap, it must
be one whose ESR is specified at a frequency of 100 kHz or
more.
Because the ESR of ceramic capacitors is only a few milli
Ohms, they are not suitable for use as output capacitors on
LP388X devices. The regulator output can tolerate ceramic
capacitance totaling up to 15% of the amount of Tantalum
capacitance connected from the output to ground.
OUTPUT "BYPASS" CAPACITORS
Many designers place small value "bypass" capacitors at
various circuit points to reduce noise. Ceramic capacitors in
the value range of about 1000pF to 0.1µF placed directly on
the output of a PNP or P-FET LDO regulator can cause a
loss of phase margin which can result in oscillations, even
when a Tantalum output capacitor is in parallel with it. This is
not unique to National Semiconductor LDO regulators, it is
true of any P-type LDO regulator.
The reason for this is that PNP or P-FET regulators have a
higher output impedance (compared to an NPN regulator),
which results in a pole-zero pair being formed by every
different capacitor connected to the output.
The zero frequency is approximately:
F
z
=1/(2XπXESRXC)
Where ESR is the equivalent series resistance of the capaci-
tor, and C is the value of capacitance.
The pole frequency is:
F
p
=1/(2XπXR
L
XC)
Where R
L
is the load resistance connected to the regulator
output.
To understand why a small capacitor can reduce phase
margin: assume a typical LDO with a bandwidth of 1MHz,
which is delivering 0.5A of current from a 2.5V output (which
means R
L
is 5 Ohms). We then place a .047 µF capacitor on
the output. This creates a pole whose frequency is:
F
p
=1/(2XπX 5 X .047 X 10E-6) = 677 kHz
This pole would add close to 60 degrees of phase lag at the
crossover (unity gain) frequency of 1 MHz, which would
almost certainly make this regulator oscillate. Depending on
the load current, output voltage, and bandwidth, there are
usually values of small capacitors which can seriously re-
duce phase margin. If the capacitors are ceramic, they tend
to oscillate more easily because they have very little internal
inductance to damp it out. If bypass capacitors are used, it is
best to place them near the load and use trace inductance to
"decouple" them from the regulator output.
INPUT CAPACITOR
The input capacitor must be at least 4.7 µF, but can be
increased without limit. It’s purpose is to provide a low
source impedance for the regulator input. Ceramic capaci-
tors work best for this, but Tantalums are also very good.
There is no ESR limitation on the input capacitor (the lower,
the better). Aluminum electrolytics can be used, but their
ESR increase very quickly at cold temperatures. They are
not recommended for any application where temperatures
go below about 10˚C.
BIAS CAPACITOR
The 0.1µF capacitor on the bias line can be any good quality
capacitor (ceramic is recommended).
BIAS VOLTAGE
The bias voltage is an external voltage rail required to get
gate drive for the N-FET pass transistor. Bias voltage must
be in the range of 4.5 - 6V to assure proper operation of the
part.
UNDER VOLTAGE LOCKOUT
The bias voltage is monitored by a circuit which prevents the
regulator output from turning on if the bias voltage is below
approximately 4V.
SHUTDOWN OPERATION
Pulling down the shutdown (S/D) pin will turn-off the regula-
tor. Pin S/D must be actively terminated through a pull-up
resistor (10 kΩto 100 kΩ) for a proper operation. If this pin
is driven from a source that actively pulls high and low (such
as a CMOS rail to rail comparator), the pull-up resistor is not
required. This pin must be tied to Vin if not used.
LP3883
www.national.com 10
Application Hints (Continued)
POWER DISSIPATION/HEATSINKING
A heatsink may be required depending on the maximum
power dissipation and maximum ambient temperature of the
application. Under all possible conditions, the junction tem-
perature must be within the range specified under operating
conditions. The total power dissipation of the device is given
by:
P
D
=(V
IN
−V
OUT
)I
OUT
+(V
IN
)I
GND
where I
GND
is the operating ground current of the device.
The maximum allowable temperature rise (T
Rmax
) depends
on the maximum ambient temperature (T
Amax
) of the appli-
cation, and the maximum allowable junction temperature
(T
Jmax
):
T
Rmax
=T
Jmax
−T
Amax
The maximum allowable value for junction to ambient Ther-
mal Resistance, θ
JA
, can be calculated using the formula:
θ
JA
=T
Rmax
/P
D
These parts are available in TO-220 and TO-263 packages.
The thermal resistance depends on amount of copper area
or heat sink, and on air flow. If the maximum allowable value
of θ
JA
calculated above is ≥60 ˚C/W for TO-220 package
and ≥60 ˚C/W for TO-263 package no heatsink is needed
since the package can dissipate enough heat to satisfy these
requirements. If the value for allowable θ
JA
falls below these
limits, a heat sink is required.
HEATSINKING TO-220 PACKAGE
The thermal resistance of a TO220 package can be reduced
by attaching it to a heat sink or a copper plane on a PC
board. If a copper plane is to be used, the values of θ
JA
will
be same as shown in next section for TO263 package.
The heatsink to be used in the application should have a
heatsink to ambient thermal resistance,
θ
HA
≤θ
JA
−θ
CH
−θ
JC
.
In this equation, θ
CH
is the thermal resistance from the case
to the surface of the heat sink and θ
JC
is the thermal resis-
tance from the junction to the surface of the case. θ
JC
is
about 3˚C/W for a TO220 package. The value for θ
CH
de-
pends on method of attachment, insulator, etc. θ
CH
varies
between 1.5˚C/W to 2.5˚C/W. If the exact value is unknown,
2˚C/W can be assumed.
HEATSINKING TO-263 PACKAGE
The TO-263 package uses the copper plane on the PCB as
a heatsink. The tab of these packages are soldered to the
copper plane for heat sinking. The graph below shows a
curve for the θ
JA
of TO-263 package for different copper area
sizes, using a typical PCB with 1 ounce copper and no solder
mask over the copper area for heat sinking.
20062425
FIGURE 1. θ
JA
vs Copper (1 Ounce) Area for TO-263
package
LP3883
www.national.com11
Application Hints (Continued)
As shown in the graph below, increasing the copper area
beyond 1 square inch produces very little improvement. The
minimum value for θ
JA
for the TO-263 package mounted to a
PCB is 32˚C/W.
Figure 2 shows the maximum allowable power dissipation
for TO-263 packages for different ambient temperatures,
assuming θ
JA
is 35˚C/W and the maximum junction tempera-
ture is 125˚C.
20062426
FIGURE 2. Maximum power dissipation vs ambient
temperature for TO-263 package
LP3883
www.national.com 12
Physical Dimensions inches (millimeters) unless otherwise noted
TO220 5-lead, Molded, Stagger Bend Package (TO220-5)
NS Package Number T05D
TO263 5-Lead, Molded, Surface Mount Package (TO263-5)
NS Package Number TS5B
LP3883
www.national.com13
Notes
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain
no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
Leadfree products are RoHS compliant.
National Semiconductor
Americas Customer
Support Center
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Support Center
Email: ap.support@nsc.com
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
LP3883 3A Fast-Response Ultra Low Dropout Linear Regulators
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated
