Product Folder Sample & Buy Support & Community Tools & Software Technical Documents LMH6654, LMH6655 SNOS956E - JUNE 2001 - REVISED AUGUST 2014 LMH6654, LMH6655 Single and Dual Low Power, 250 MHz, Low Noise Amplifiers 1 Features 3 Description * The LMH6654 and LMH6655 single and dual high speed voltage feedback amplifiers are designed to have unity-gain stable operation with a bandwidth of 250 MHz. They operate from 2.5 V to 6 V and each channel consumes only 4.5 mA. The amplifiers feature very low voltage noise and wide output swing to maximize signal-to-noise ratio, and possess a true single supply capability with input common mode voltage range extending 150 mV below negative rail and within 1.3 V of the positive rail. The high speed and low power combination of the LMH6654 and LMH6655 make these products an ideal choice for many portable, high speed applications where power is at a premium. 1 * * * * * * * * * * (VS = 5 V, TJ = 25 C, Typical Values Unless Specified) Voltage Feedback Architecture Unity Gain Bandwidth 250 MHz Supply Voltage Range 2.5V to 6V Slew Rate 200 V/sec Supply Current 4.5 mA/channel Input Common Mode Voltage -5.15V to +3.7V Output Voltage Swing (RL = 100 ) -3.6V to 3.4V Input Voltage Noise 4.5 nV/Hz Input Current Noise 1.7 pA/Hz Settling Time to 0.01% 25 ns 2 Applications * * * * * * ADC Drivers Consumer Video Active Filters Pulse Delay Circuits xDSL Receiver Pre-amps The LMH6654 and LMH6655 are built on TI's Advance VIP10TM (Vertically Integrated PNP) complementary bipolar process. The LMH6654 is packaged in 5-Pin SOT-23 and 8Pin SOIC. The LMH6655 is packaged in 8-Pin VSSOP (DGK) and 8-Pin SOIC. Device Information(1) PART NUMBER PACKAGE BODY SIZE (NOM) LMH6654 SOIC (8) 4.90 mm x 3.91 mm LMH6654 SOT-23 (5) 2.90 mm x 1.60 mm LMH6655 SOIC (8) 4.90 mm x 3.91 mm LMH6655 VSSOP (8) 3.00 mm x 3.00 mm (1) For all available packages, see the orderable addendum at the end of the datasheet. Figure 1. Input Voltage and Curernt Noise vs. Frequency (Vs= 5V) 100 10 en 10 in 1 100 1k 100k 10k FREQUENCY (Hz) 1M INPUT CURRENT NOISE (pA/ Hz) INPUT VOLTAGE NOISE (nV/ Hz) 100 1 10M 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LMH6654, LMH6655 SNOS956E - JUNE 2001 - REVISED AUGUST 2014 www.ti.com Table of Contents 1 2 3 4 5 6 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 4 6.1 6.2 6.3 6.4 6.5 6.6 6.7 4 4 4 4 5 7 9 Absolute Maximum Ratings ...................................... Handling Ratings....................................................... Recommended Operating Conditions....................... Thermal Information .................................................. 5V Electrical Characteristics ................................... 5V Electrical Characteristics ..................................... Typical Characteristics .............................................. 7 Application and Implementation ........................ 16 7.1 Application Information............................................ 16 7.2 Typical Application .................................................. 16 8 Power Supply Recommendations...................... 20 9 Layout ................................................................... 20 8.1 Power Dissipation ................................................... 20 9.1 Layout Guidelines ................................................... 20 10 Device and Documentation Support ................. 21 10.1 Documentation Support ........................................ 21 10.2 Electrostatic Discharge Caution ............................ 21 10.3 Glossary ................................................................ 21 11 Mechanical, Packaging, and Orderable Information ........................................................... 21 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision D (March 2013) to Revision E Page * Changed data sheet structure and organization. Added, updated, or renamed the following sections: Device Information Table, Application and Implementation; Power Supply Recommendations; Device and Documentation Support; Mechanical, Packaging, and Ordering Information. Deleted Switching Characteristics due to redundancy. ......... 1 * Changed from Junction Temperature Range to "Operating Temperature Range" ................................................................ 4 * Deleted TJ = 25C................................................................................................................................................................... 5 * Deleted TJ = 25C .................................................................................................................................................................. 7 Changes from Revision C (March 2013) to Revision D * 2 Page Changed layout of National Data Sheet to TI format ........................................................................................................... 19 Submit Documentation Feedback Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 LMH6654, LMH6655 www.ti.com SNOS956E - JUNE 2001 - REVISED AUGUST 2014 5 Pin Configuration and Functions 5-Pin (LMH6654) Package DBV Top View 8-Pin (LMH6654) Package D Top View 5 1 OUTPUT V 1 + 8-Pin (LMH6655) SOIC and VSSOP (DGK) Top View 8 N/C 1 N/C 8 + V OUT A A -IN V - 2 7 - + V 2 - + 7 -IN A 2 + +IN - 3 6 + OUT B OUTPUT 3 6 +IN A +IN 4 3 -IN - 4 + N/C V V - -IN B B 5 4 5 +IN B Pin Functions PIN NAME LMH6654 LMH6655 I/O DESCRIPTION DBV D DGK -IN 4 2 I Inverting Input +IN 3 3 I Non-inverting Input -IN A 2 I ChA Inverting Input +IN A 3 I ChA Non-inverting Input -IN B 6 I ChB Inverting Input I ChB Non-inverting Input +IN B 5 N/C 1, 5, 8 OUT A OUT B -- No Connection 1 O ChA Output 7 O ChB Output O Output OUTPUT 1 6 V- 2 4 4 I Negative Supply V+ 5 7 8 I Positive Supply Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 Submit Documentation Feedback 3 LMH6654, LMH6655 SNOS956E - JUNE 2001 - REVISED AUGUST 2014 www.ti.com 6 Specifications 6.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) MIN VIN Differential Output Short Circuit Duration See Voltage at Input pins Soldering Information (1) (2) (3) UNIT 1.2 V (2) Supply Voltage (V+ - V-) Junction Temperature MAX (3) 13.2 V V+ +0.5 V- -0.5 V 150 C Infrared or Convection (20 sec.) 235 C Wave Soldering (10 sec.) 260 C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature at 150C. The maximum power dissipation is a function of TJ(MAX), RJA and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA)/RJA. All numbers apply for packages soldered directly onto a PC board. 6.2 Handling Ratings Tstg Storage temperature range V(ESD) (1) (2) (3) Electrostatic discharge (1) MIN MAX UNIT -65 150 C Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins (2) 2000 Machine model (MM) (3) 200 V Human body model, 1.5 k in series with 100 pF. Machine model: 0 in series with 100 pF. JEDEC document JEP155 states that 2000-V HBM allows safe manufacturing with a standard ESD control process. JEDEC document JEP157 states that 200-V MM allows safe manufacturing with a standard ESD control process. 6.3 Recommended Operating Conditions (1) over operating free-air temperature range (unless otherwise noted) MIN NOM MAX UNIT Supply Voltage (V+ - V-) 2.5 6.0 V Operating Temperature Range -40 85 C (1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test conditions, see the Electrical Characteristics Table. 6.4 Thermal Information THERMAL METRIC (1) RJA (1) 4 Junction-to-ambient thermal resistance SOIC (D) VSSOP (DGK) SOT-23 (D) 8 PINS 8 PINS 5 PINS 172 235 265 UNIT C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. Submit Documentation Feedback Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 LMH6654, LMH6655 www.ti.com SNOS956E - JUNE 2001 - REVISED AUGUST 2014 6.5 5V Electrical Characteristics Unless otherwise specified, all limits ensured for V+ = +5V, V- = -5V, VCM = 0V, AV = +1, RF = 25 for gain = +1, RF = 402 for gain +2, and RL = 100. Boldface limits apply at the temperature extremes. PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT DYNAMIC PERFORMANCE fCL Close Loop Bandwidth GBWP m AV = +1 250 AV = +2 130 AV = +5 52 AV = +10 26 Gain Bandwidth Product AV +5 Bandwidth for 0.1 dB Flatness AV +1 Phase Margin (3) AV = +1, VIN = 2 VPP MHz 260 MHz 18 MHz 50 deg 200 V/s 25 ns SR Slew Rate tS Settling Time 0.01% 15 ns tr Rise Time AV = +1, 0.2V Step 1.4 ns tf Fall Time AV = +1, 0.2V Step 1.2 ns AV = +1, 2V Step 0.1% DISTORTION and NOISE RESPONSE en Input Referred Voltage Noise f 0.1 MHz 4.5 nV/Hz in Input-Referred Current Noise f 0.1 MHz 1.7 pA/Hz Second Harmonic Distortion AV = +1, f = 5 MHz -80 Third Harmonic Distortion VO = 2 VPP, RL = 100 -85 Xt Crosstalk (for LMH6655 only) Input Referred, 5 MHz, Channel-to-Channel -80 DG Differential Gain AV = +2, NTSC, RL = 150 0.01% DP Differential Phase AV = +2, NTSC, RL = 150 0.025 dBc dB deg INPUT CHARACTERISTICS VOS Input Offset Voltage VCM = 0V TC VOS Input Offset Average Drift VCM = 0V IB Input Bias Current VCM = 0V IOS Input Offset Current VCM = 0V RIN Input Resistance -3 -4 (4) 1 3 4 6 -1 -2 Common Mode mV V/C 5 12 18 A 0.3 1 2 A 4 M Differential Mode 20 k Common Mode 1.8 CIN Input Capacitance CMRR Common Mode Rejection Ration Input Referred, VCM = 0V to -5V CMVR Input Common- Mode Voltage Range CMRR 50 dB Differential Mode pF 1 70 68 90 -5.15 3.5 3.7 60 58 67 dB -5.0 V TRANSFER CHARACTERISTICS AVOL (1) (2) (3) (4) VO = 4 VPP, RL = 100 Large Signal Voltage Gain dB All limits are specified by testing or statistical analysis. Typical Values represent the most likely parametric norm. Slew rate is the slower of the rising and falling slew rates. Slew rate is rate of change from 10% to 90% of output voltage step. Offset voltage average drift is determined by dividing the change in VOS at temperature extremes into the total temperature change. Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 Submit Documentation Feedback 5 LMH6654, LMH6655 SNOS956E - JUNE 2001 - REVISED AUGUST 2014 www.ti.com 5V Electrical Characteristics (continued) Unless otherwise specified, all limits ensured for V+ = +5V, V- = -5V, VCM = 0V, AV = +1, RF = 25 for gain = +1, RF = 402 for gain +2, and RL = 100. Boldface limits apply at the temperature extremes. PARAMETER TEST CONDITIONS MIN (1) TYP (2) 3.4 3.2 3.6 MAX (1) UNIT OUTPUT CHARACTERISTICS VO ISC Output Swing High No Load Output Swing Low No Load Output Swing High RL = 100 Output Swing Low RL = 100 Short Circuit Current IOUT Output Current RO Output Resistance (5) -3.9 3.2 3.0 V 3.4 -3.6 Sourcing, VO = 0V VIN = 200 mV 145 130 280 Sinking, VO = 0V VIN = 200 mV 100 80 185 Sourcing, VO = +3V -3.7 -3.5 -3.4 -3.2 mA 80 Sinking, VO = -3V 120 AV = +1, f <100 kHz 0.08 mA POWER SUPPLY PSRR Power Supply Rejection Ratio IS Supply Current (per channel) (5) 6 Input Referred, VS = 5V to 6V 60 dB 76 4.5 6 7 mA Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature at 150C. Submit Documentation Feedback Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 LMH6654, LMH6655 www.ti.com SNOS956E - JUNE 2001 - REVISED AUGUST 2014 6.6 5V Electrical Characteristics Unless otherwise specified, all limits ensured for V+ = +5V, V- = -0V, VCM = 2.5V, AV = +1, RF = 25 for gain = +1, RF = 402 for gain +2, and RL = 100 to V+/2. Boldface limits apply at the temperature extremes. PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT DYNAMIC PERFORMANCE fCL Close Loop Bandwidth GBWP m AV = +1 230 AV = +2 120 AV = +5 50 AV = +10 25 MHz Gain Bandwidth Product AV +5 250 MHz Bandwidth for 0.1 dB Flatness AV = +1 17 MHz 48 deg 190 V/s Phase Margin (3) SR Slew Rate tS Settling Time 0.01% AV = +1, VIN = 2 VPP 20 ns tr Rise Time AV = +1, 0.2V Step 1.5 ns tf Fall Time AV = +1, 0.2V Step 1.35 ns ns 30 AV = +1, 2V Step 0.1% DISTORTION and NOISE RESPONSE en Input Referred Voltage Noise f 0.1 MHz 4.5 nV/Hz in Input Referred Current Noise f 0.1 MHz 1.7 pA/Hz Second Harmonic Distortion AV = +1, f = 5 MHz -65 Third Harmonic Distortion VO = 2 VPP, RL = 100 -70 Crosstalk (for LMH6655 only) Input Referred, 5 MHz -78 Xt dBc dB INPUT CHARACTERISTICS VOS Input Offset Voltage TC VOS -5 -6.5 VCM = 2.5V Input Offset Average Drift VCM = 2.5V IB Input Bias Current VCM = 2.5V IOS Input Offset Current VCM = 2.5V RIN Input Resistance (4) Input Capacitance CMRR Common Mode Rejection Ration CMVR Input Common Mode Voltage Range 5 6.5 6 -2 -3 Common Mode CIN 2 mV V/C 6 12 18 A 0.5 2 3 A 4 M Differential Mode 20 k Common Mode 1.8 Differential Mode Input Referred, VCM = 0V to -2.5V pF 1 70 68 CMRR 50 dB 90 -0.15 3.5 3.7 58 55 64 dB 0 V TRANSFER CHARACTERISTICS AVOL (1) (2) (3) (4) VO = 1.6 VPP, RL = 100 Large Signal Voltage Gain dB All limits are specified by testing or statistical analysis. Typical Values represent the most likely parametric norm. Slew rate is the slower of the rising and falling slew rates. Slew rate is rate of change from 10% to 90% of output voltage step. Offset voltage average drift is determined by dividing the change in VOS at temperature extremes into the total temperature change. Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 Submit Documentation Feedback 7 LMH6654, LMH6655 SNOS956E - JUNE 2001 - REVISED AUGUST 2014 www.ti.com 5V Electrical Characteristics (continued) Unless otherwise specified, all limits ensured for V+ = +5V, V- = -0V, VCM = 2.5V, AV = +1, RF = 25 for gain = +1, RF = 402 for gain +2, and RL = 100 to V+/2. Boldface limits apply at the temperature extremes. PARAMETER TEST CONDITIONS MIN (1) TYP (2) 3.6 3.4 3.75 MAX (1) UNIT OUTPUT CHARACTERISTICS VO ISC Output Swing High No Load Output Swing Low No Load Output Swing High RL = 100 Output Swing Low RL = 100 Short Circuit Current IOUT Output Current RO Output Resistance (5) 0.9 3.5 3.35 1.1 1.3 V 3.70 1 Sourcing , VO = 2.5V VIN = 200 mV 90 80 170 Sinking, VO = 2.5V VIN = 200 mV 70 60 140 1.3 1.45 mA Sourcing, VO = +3.5V 30 Sinking, VO = 1.5V 60 AV = +1, f <100 kHz .08 mA POWER SUPPLY PSRR Power Supply Rejection Ratio IS Supply Current (per channel) (5) 8 Input Referred , VS = 2.5V to 3V 60 dB 75 4.5 6 7 mA Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature at 150C. Submit Documentation Feedback Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 LMH6654, LMH6655 www.ti.com SNOS956E - JUNE 2001 - REVISED AUGUST 2014 6.7 Typical Characteristics 4 9 2 6 0 3 -2 0 -4 -3 GAIN (dB) GAIN (dB) 25C, V+ = 5 V, V- = -5, RF = 25 for gain = +1, RF = 402 for gain +2 and RL = 100 , unless otherwise specified. VS = 2.5V -6 -8 VS = 5V -10 -9 -15 -14 -18 10M 100M FREQUENCY (Hz) -21 1M 1G Figure 2. Closed Loop Bandwidth (G = +1) VS = 5V 10M 100M FREQUENCY (Hz) 1G Figure 3. Closed Loop Bandwidth (G = +2) 25 24 20 19 VS = 5V 14 9 10 4 5 -1 -6 VS = 2.5V -11 0 -5 -10 -16 -15 -21 -20 -26 1M 10M 100M FREQUENCY (dB) VS = 5V 15 GAIN (dB) GAIN (dB) VS = 2.5V -12 -12 -16 1M -25 1M 1G Figure 4. Closed Loop Bandwidth (G = +5) VS = 2.5V 1G 10M 100M FREQUENCY (Hz) Figure 5. Closed Loop Bandwidth (G = +10) 5.0 5 4.9 4.9 85C 4.8 SUPPLY CURRENT (mA) SUPPLY CURRENT (mA) -6 4.7 4.6 4.5 4.4 25C 4.3 -40C 4.8 4.7 VS = 5V 4.6 4.5 4.4 4.2 4.3 4.1 4.2 20 40 60 -60 -40 -20 0 TEMPERATURE (C) 4 5 6 7 8 9 10 SUPPLY VOLTAGE (V) 11 12 Figure 6. Supply Current per Channel vs. Supply Voltage VS = 5V 80 100 Figure 7. Supply Current per Channel vs. Temperature Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 Submit Documentation Feedback 9 LMH6654, LMH6655 SNOS956E - JUNE 2001 - REVISED AUGUST 2014 www.ti.com Typical Characteristics (continued) 25C, V+ = 5 V, V- = -5, RF = 25 for gain = +1, RF = 402 for gain +2 and RL = 100 , unless otherwise specified. 0 0 -0.2 -0.1 VS = 5V -40C -40C -0.2 VOS (mV) -0.6 85C -0.8 25C -0.3 85C -0.4 25C -0.5 -1 -0.6 -1.2 4 5 6 7 8 9 VSUPPLY (V) 10 11 0 12 2 3 4 5 VCM (V) 6 7 8 Figure 9. Offset Voltage vs. Common Mode Figure 8. Offset Voltage vs. Supply Voltage (VCM = 0V) 0 7 VS = 2.5V IBIAS INPUT BIAS CURRENT (A) -0.1 -0.2 -0.3 VOS (mV) 1 -0.4 -40C -0.5 -0.6 25C -0.7 -0.8 85C 6 OFFSET VOLTAGE (mV) VOS (mV) -0.4 5 4 3 2 VOS 1 -0.9 -1 0 0.5 1 1.5 2 2.5 3 3.5 0 -50 0 50 100 TEMPERATURE (C) VCM (V) Figure 11. Bias Current and Offset Voltage vs. Temperature Figure 10. Offset Voltage vs. Common Mode 7 -40C VS = 5V 6 POSITIVE IBIAS (A) 25C 5 4 85C 3 2 1 0 -1 0 0.5 1 1.5 2 2.5 3 3.5 VCM (V) Figure 13. Bias Current vs. Common Mode Voltage Figure 12. Bias Current vs. Common Mode Voltage 10 Submit Documentation Feedback Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 LMH6654, LMH6655 www.ti.com SNOS956E - JUNE 2001 - REVISED AUGUST 2014 Typical Characteristics (continued) 25C, V+ = 5 V, V- = -5, RF = 25 for gain = +1, RF = 402 for gain +2 and RL = 100 , unless otherwise specified. INPUT 110 100 (1 V/div) CMRR 90 PSRR 80 OUTPUT AoL, PSRR, AND CMRR (dB) 120 70 AoL @ 5V 60 -50 AoL @ 5V 0 50 100 TIME (12.5 ns/div) TEMPERATURE (C) OUTPUT OUTPUT (1 V/div) (1 V/div) INPUT INPUT Figure 14. AOL, PSRR and CMRR vs. Temperature Figure 15. Inverting Large Signal Pulse Response (VS = 5V) TIME (12.5 ns/div) TIME (12.5 ns/div) Figure 17. Non-Inverting Large Signal Pulse Response (VS = 5V) OUTPUT OUTPUT (1 V/div) (100 mV/div) INPUT INPUT Figure 16. Inverting Large Signal Pulse Response (VS = 5V) TIME (12.5 ns/div) TIME (12.5 ns/div) Figure 18. Non-Inverting Large Signal Pulse Response (VS = 5V) Figure 19. Non-Inverting Small Signal Pulse Response (VS = 5V) Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 Submit Documentation Feedback 11 LMH6654, LMH6655 SNOS956E - JUNE 2001 - REVISED AUGUST 2014 www.ti.com Typical Characteristics (continued) OUTPUT OUTPUT (100 mV/div) (100 mV/div) INPUT INPUT 25C, V+ = 5 V, V- = -5, RF = 25 for gain = +1, RF = 402 for gain +2 and RL = 100 , unless otherwise specified. TIME (12.5 ns/div) TIME (12.5 ns/div) Figure 21. Inverting Small Signal Pulse Response (VS = 5V) OUTPUT (100 mV/div) INPUT VOLTAGE NOISE (nV/ Hz) INPUT 100 100 10 en 10 in 1 100 1k 100k 10k FREQUENCY (Hz) 1M INPUT CURRENT NOISE (pA/ Hz) Figure 20. Non-Inverting Small Signal Pulse Response (VS = 5V) 1 10M TIME (12.5 ns/div) Figure 22. Inverting Small Signal Pulse Response (VS = 5V) 100 en 10 in 1 100 1k 100k 10k FREQUENCY (Hz) 1M 1 10M HARMONIC DISTORTION (dBc) 10 -30 INPUT CURRENT NOISE (pA/ Hz) INPUT VOLTAGE NOISE (nV/ Hz) 100 Figure 23. Input Voltage and Current Noise vs. Frequency (VS = 5V) -40 -50 -60 3RD -70 2ND -80 -90 -100 -110 0.1 Figure 24. Input Voltage and Current Noise vs. Frequency (VS = 5V) 12 Submit Documentation Feedback 1 10 100 FREQUENCY (MHz) Figure 25. Harmonic Distortion vs. Frequency G = +1, VO = 2 VPP, VS = 5V Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 LMH6654, LMH6655 www.ti.com SNOS956E - JUNE 2001 - REVISED AUGUST 2014 Typical Characteristics (continued) -30 -60 -40 -65 HARMONIC DISTORTION (dBc) HARMONIC DISTORTION (dBc) 25C, V+ = 5 V, V- = -5, RF = 25 for gain = +1, RF = 402 for gain +2 and RL = 100 , unless otherwise specified. -50 -60 -70 -80 3RD -90 2ND -100 -110 0.1 1 10 2ND -70 -75 -80 3RD -85 -90 -95 -100 20 40 60 -60 -40 -20 0 TEMPERATURE (C) 100 FREQUENCY (MHz) 80 100 Figure 27. Harmonic Distortion vs. Temperature VS = 5V, f = 5 MHz, VO = 2 VPP Figure 26. Harmonic Distortion vs. Frequency G = +1, VO = 2 VPP, VS = 5V -45 -60 HARMONIC DISTORTION (dBc) HARMONIC DISTORTION (dBc) 2ND -65 -70 -75 3RD -80 -85 2ND -90 -50 -55 -60 -65 -70 3RD -75 -80 -85 -90 -95 -95 -100 20 40 60 -60 -40 -20 0 TEMPERATURE (C) 1 80 2 3 4 100 5 6 7 8 9 10 GAIN (V/V) Figure 29. Harmonic Distortion vs. Gain VS = 5V, f = 5 MHz, VO = 2 VPP Figure 28. Harmonic Distortion vs. Temperature VS = 5V, f = 5 MHz, VO = 2 VPP -45 -30 HARMONIC DISTORTION (dBc) HARMONIC DISTORTION (dBc) -50 2ND -55 -60 -65 -70 -75 -80 3RD -85 -90 -95 1 2 3 4 5 6 7 8 9 10 -40 -50 2ND -60 -70 -80 3RD -90 -100 0.0 0.5 1.0 1.5 2.0 2.5 GAIN (V/V) OUTPUT SWING (VPP) Figure 30. Harmonic Distortion vs. Gain VS = 5V, f = 5 MHz, VO = 2 VPP Figure 31. Harmonic Distortion vs. Output Swing (G = +2, VS = 5V, f = 5 MHz) Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 Submit Documentation Feedback 13 LMH6654, LMH6655 SNOS956E - JUNE 2001 - REVISED AUGUST 2014 www.ti.com Typical Characteristics (continued) 25C, V+ = 5 V, V- = -5, RF = 25 for gain = +1, RF = 402 for gain +2 and RL = 100 , unless otherwise specified. 100 -30 NEGATIVE 80 -50 70 PSRR (dB) HARMONIC DISTORTION (dBc) 90 -40 2ND -60 -70 60 POSITIVE 50 40 30 -80 3RD 20 -90 10 0 10 -100 0 1 2 3 4 5 6 7 8 100 10k 1k 100k 1M 10M OUTPUT SWING (VPP) FREQUENCY (Hz) Figure 32. Harmonic Distortion vs. Output Swing (G = +2, VS = 5V, f = 5 MHz) Figure 33. PSRR vs. Frequency 5 120 VOUT REFERENCED TO V (V) VS = 5V 4 - 100 CMRR (dB) 80 60 40 20 0 10 3 2 VS = 5V 1 VS = 5V 100 1k 10k 100k FREQUENCY 1M 0 .01 10M 0.1 1 10 1 k 100 OUTPUT SINKING CURRENT (mA) Figure 34. CMRR vs. Frequency Figure 35. Output Sinking Current -20 VS = 5V -30 CROSSTALK REJECTION (dB) + VOUT REFERENCED TO V (V) 5 4 3 VS = 5V 2 1 VS = 5V 0 .01 0.1 1 10 100 -40 -50 -60 -70 -80 -90 -100 -110 1 k -120 100k OUTPUT SOURCING CURRENT (mA) Submit Documentation Feedback 100M Figure 37. CrossTalk vs. Frequency (LMH6655 only) Figure 36. Output Sourcing Current 14 10M 1M FREQUENCY (Hz) Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 LMH6654, LMH6655 www.ti.com SNOS956E - JUNE 2001 - REVISED AUGUST 2014 Typical Characteristics (continued) 25C, V+ = 5 V, V- = -5, RF = 25 for gain = +1, RF = 402 for gain +2 and RL = 100 , unless otherwise specified. -20 100 VS = 5V ISOLATION RESISTANCE, RISO (:) CROSSTALK REJECTION (dB) -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 100k 25: 90 + 80 x 70 RISO CL 1 k: 60 50 40 30 20 10 0 10M 1M FREQUENCY (Hz) 100M 0 10 20 30 40 50 60 70 80 90 100 CAPACITIVE LOAD, CL (pF) Figure 38. CrossTalk vs. Frequency (LMH6655 only) Figure 39. Isolation Resistance vs. Capacitive Load 100 90 80 180 GAIN (dB) 144 60 108 50 72 40 36 30 0 20 -36 GAIN 10 -72 0 -108 -10 -144 -20 1k PHASE () PHASE 70 -180 10k 100k 1M 10M 100M 500M FREQUENCY (Hz) Figure 40. Open Loop Gain and Phase vs. Frequency Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 Submit Documentation Feedback 15 LMH6654, LMH6655 SNOS956E - JUNE 2001 - REVISED AUGUST 2014 www.ti.com 7 Application and Implementation 7.1 Application Information The LMH6654 single and LMH6655 dual high speed, voltage feedback amplifiers are manufactured on TI's new VIP10TM (Vertically Integrated PNP) complementary bipolar process. These amplifiers can operate from 2.5 V to 6 V power supply. They offer low supply current, wide bandwidth, very low voltage noise and large output swing. Many of the typical performance plots found in the datasheet can be reproduced if 50 coax and 50 RIN/ROUT resistors are used. 7.2 Typical Application 7.2.1 Design Requirements 7.2.1.1 Components Selection and Feedback Resistor It is important in high-speed applications to keep all component leads short since wires are inductive at high frequency. For discrete components, choose carbon composition axially leaded resistors and micro type capacitors. Surface mount components are preferred over discrete components for minimum inductive effect. Never use wire wound type resistors in high frequency applications. Large values of feedback resistors can couple with parasitic capacitance and cause undesired effects such as ringing or oscillation in high-speed amplifiers. Keep resistors as low as possible consistent with output loading consideration. For a gain of 2 and higher, 402 feedback resistor used for the typical performance plots gives optimal performance. For unity gain follower, a 25 feedback resistor is recommended rather than a direct short. This effectively reduces the Q of what would otherwise be a parasitic inductance (the feedback wire) into the parasitic capacitance at the inverting input. 7.2.2 Detailed Design Procedure 7.2.2.1 Driving Capacitive Loads Capacitive loads decrease the phase margin of all op amps. The output impedance of a feedback amplifier becomes inductive at high frequencies, creating a resonant circuit when the load is capacitive. This can lead to overshoot, ringing and oscillation. To eliminate oscillation or reduce ringing, an isolation resistor can be placed as shown in Figure 41 below. At frequencies above 1 F= 2 S RISO CLOAD (1) the load impedance of the Amplifier approaches RISO. The desired performance depends on the value of the isolation resistor. The isolation resistance vs. capacitance load graph in the typical performance characteristics provides the means for selection of the value of RS that provides 3 dB peaking in closed loop AV = 1 response. In general, the bigger the isolation resistor, the more damped the pulse response becomes. For initial evaluation, a 50 isolation resistor is recommended. 25: - RISO VOUT VIN + Figure 41. Isolation Resistor Placement 16 Submit Documentation Feedback Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 LMH6654, LMH6655 www.ti.com SNOS956E - JUNE 2001 - REVISED AUGUST 2014 Typical Application (continued) 7.2.2.2 Bias Current Cancellation In order to cancel the bias current errors of the non-inverting configuration, the parallel combination of the gain setting Rg and feedback Rf resistors should equal the equivalent source resistance Rseq as defined in Figure 42. Combining this constraint with the non-inverting gain equation, allows both Rf and Rg to be determined explicitly from the following equations: Rf = AVRseq and Rg = Rf/(AV-1) (2) For inverting configuration, bias current cancellation is accomplished by placing a resistor Rb on the non-inverting input equal in value to the resistance seen by the inverting input (Rf//(Rg+Rs). The additional noise contribution of Rb can be minimized through the use of a shunt capacitor. Figure 42. Non-Inverting Amplifier Configuration Figure 43. Inverting Amplifier Configuration Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 Submit Documentation Feedback 17 LMH6654, LMH6655 SNOS956E - JUNE 2001 - REVISED AUGUST 2014 www.ti.com Typical Application (continued) 7.2.2.3 Total Input Noise vs. Source Resistance The noise model for the non-inverting amplifier configuration showing all noise sources is described in Figure 44. In addition to the intrinsic input voltage noise (en) and current noise (in = in+ = in-) sources, there also exits thermal voltage noise et = 4kTR associated with each of the external resistors. Equation 3 provides the general form for total equivalent input voltage noise density (eni). Equation 4 is a simplification of Equation 3 that assumes Rf || Rg = Rseq for bias current cancellation. Figure 45 illustrates the equivalent noise model using this assumption. The total equivalent output voltage noise (eno) is eni * AV. Figure 44. Non-Inverting Amplifier Noise Model eni = en2 + (in+ * RSeq)2 + 4kTRSeq + (in- * (Rf || Rg))2 + 4kT(Rf || Rg) (3) Figure 45. Noise Model with Rf || Rg = Rseq eni = en2 + 2 (in * RSeq)2 + 4kT (2RSeq) (4) If bias current cancellation is not a requirement, then Rf || Rg does not need to equal Rseq. In this case, according to Equation 3, Rf and Rg should be as low as possible in order to minimize noise. Results similar to Equation 3 are obtained for the inverting configuration on if Rseq is replaced by Rb || Rg is replaced by Rg + Rs. With these substitutions, Equation 3 will yield an eni referred to the non-inverting input. Referring eni to the inverting input is easily accomplished by multiplying eni by the ratio of non-inverting to inverting gains. 18 Submit Documentation Feedback Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 LMH6654, LMH6655 www.ti.com SNOS956E - JUNE 2001 - REVISED AUGUST 2014 Typical Application (continued) 7.2.2.3.1 Noise Figure Noise Figure (NF) is a measure of the noise degradation caused by an amplifier. Si/Ni NF = 10LOG So/No eni = 10LOG 2 2 et (5) The noise figure formula is shown in Equation 5. The addition of a terminating resistor RT, reduces the external thermal noise but increases the resulting NF. The NF is increased because the RT reduces the input signal amplitude thus reducing the input SNR. en2 + in2 (RSeq + (Rf || Rg))2 + 4KTRSeq + 4kt (Rf || Rg) 4kTRSeq (6) The noise figure is related to the equivalent source resistance (Rseq) and the parallel combination of Rf and Rg. To minimize noise figure, the following steps are recommended: 1. Minimize Rf||Rg 2. Choose the Optimum Rs (ROPT) ROPT is the point at which the NF curve reaches a minimum and is approximated by: ROPT (en/in) Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 Submit Documentation Feedback 19 LMH6654, LMH6655 SNOS956E - JUNE 2001 - REVISED AUGUST 2014 www.ti.com 8 Power Supply Recommendations 8.1 Power Dissipation The package power dissipation should be taken into account when operating at high ambient temperature and/or high power dissipative conditions. In determining maximum operable temperature of the device, make sure the total power dissipation of the device is considered; this power dissipated in the device with a load connected to the output as well as the nominal dissipation of the op amp. 9 Layout 9.1 Layout Guidelines With all high frequency devices, board layouts with stray capacitance have a strong influence on the AC performance. The LMH6654/LMH6655 are not exception and the inverting input and output pins are particularly sensitive to the coupling of parasitic capacitance to AC ground. Parasitic capacitances on the inverting input and output nodes to ground could cause frequency response peaking and possible circuit oscillation. Therefore, the power supply, ground traces and ground plan should be placed away from the inverting input and output pins. Also, it is very important to keep the parasitic capacitance across the feedback to an absolute minimum. The PCB should have a ground plane covering all unused portion of the component side of the board to provide a low impedance path. All trace lengths should be minimized to reduce series inductance. Supply bypassing is required for the amplifiers performance. The bypass capacitors provide a low impedance return current path at the supply pins. They also provide high frequency filtering on the power supply traces. It is recommended that a ceramic decoupling capacitor 0.1 F chip should be placed with one end connected to the ground plane and the other side as close as possible to the power pins. An additional 10 F tantalum electrolytic capacitor should be connected in parallel, to supply current for fast large signal changes at the output. + V 10 F + 0.1 F 0.1 F + 10 F V - Figure 46. Supply Bypass Capacitors 9.1.1 Evaluation Boards TI provides the following evaluation boards as a guide for high frequency layout and as an aid in device testing and characterization. 20 DEVICE PACKAGE EVALULATION BOARD PN LMH6654MF 5-Pin SOT-23 LMH730216 LMH6654MA 8-Pin SOIC LMH730227 LMH6655MA 8-Pin SOIC LMH730036 LMH6655MM 8-Pin VSSOP (DGK) LMH730123 Submit Documentation Feedback Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 LMH6654, LMH6655 www.ti.com SNOS956E - JUNE 2001 - REVISED AUGUST 2014 Components Needed to Evaluate the LMH6654 on the LMH730227 Evaluation Board: * Rf, Rg use the datasheet to select values. * RIN, ROUT typically 50 (Refer to the Basic Operation section of the evaluation board datasheet for details) * Rf is an optional resistor for inverting again configurations (select Rf to yield desired input impedance = Rg||Rf) * C1, C2 use 0.1 F ceramic capacitors * C3, C4 use 10 F tantalum capacitors Components not used: 1. C5, C6, C7, C8 2. R1 thru R8 The evaluation boards are designed to accommodate dual supplies. The board can be modified to provide single operation. For best performance; 1) Do not connect the unused supply. 2) Ground the unused supply pin. 10 Device and Documentation Support 10.1 Documentation Support 10.1.1 Related Documentation 10.1.1.1 Related Links The table below lists quick access links. Categories include technical documents, support and community resources, tools and software, and quick access to sample or buy. Table 1. Related Links PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL DOCUMENTS TOOLS & SOFTWARE SUPPORT & COMMUNITY LMH6654 Click here Click here Click here Click here Click here LMH6655 Click here Click here Click here Click here Click here 10.2 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 10.3 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 11 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. Copyright (c) 2001-2014, Texas Instruments Incorporated Product Folder Links: LMH6654 LMH6655 Submit Documentation Feedback 21 PACKAGE OPTION ADDENDUM www.ti.com 20-Feb-2017 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LMH6654MA/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMH66 54MA LMH6654MAX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMH66 54MA LMH6654MF NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 85 A66A LMH6654MF/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 A66A LMH6654MFX/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 A66A LMH6655MA NRND SOIC D 8 95 TBD Call TI Call TI -40 to 85 LMH66 55MA LMH6655MA/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMH66 55MA LMH6655MAX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMH66 55MA LMH6655MM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 A67A LMH6655MMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 A67A (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 20-Feb-2017 (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 8-Feb-2017 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LMH6654MAX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LMH6654MF SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LMH6654MF/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LMH6654MFX/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LMH6655MAX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LMH6655MM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LMH6655MMX/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 8-Feb-2017 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LMH6654MAX/NOPB SOIC D 8 2500 367.0 367.0 35.0 LMH6654MF SOT-23 DBV 5 1000 210.0 185.0 35.0 LMH6654MF/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LMH6654MFX/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LMH6655MAX/NOPB SOIC D 8 2500 367.0 367.0 35.0 LMH6655MM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0 LMH6655MMX/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0 Pack Materials-Page 2 PACKAGE OUTLINE DBV0005A SOT-23 - 1.45 mm max height SCALE 4.000 SMALL OUTLINE TRANSISTOR C 3.0 2.6 1.75 1.45 PIN 1 INDEX AREA 1 0.1 C B A 5 2X 0.95 1.9 1.45 MAX 3.05 2.75 1.9 2 4 0.5 5X 0.3 0.2 3 (1.1) C A B 0.15 TYP 0.00 0.25 GAGE PLANE 8 TYP 0 0.22 TYP 0.08 0.6 TYP 0.3 SEATING PLANE 4214839/C 04/2017 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Refernce JEDEC MO-178. www.ti.com EXAMPLE BOARD LAYOUT DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X (0.95) 3 4 (R0.05) TYP (2.6) LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:15X SOLDER MASK OPENING METAL SOLDER MASK OPENING METAL UNDER SOLDER MASK EXPOSED METAL EXPOSED METAL 0.07 MIN ARROUND 0.07 MAX ARROUND NON SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED SOLDER MASK DETAILS 4214839/C 04/2017 NOTES: (continued) 4. Publication IPC-7351 may have alternate designs. 5. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X(0.95) 4 3 (R0.05) TYP (2.6) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:15X 4214839/C 04/2017 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 7. Board assembly site may have different recommendations for stencil design. www.ti.com PACKAGE OUTLINE DBV0005A SOT-23 - 1.45 mm max height SCALE 4.000 SMALL OUTLINE TRANSISTOR C 3.0 2.6 1.75 1.45 PIN 1 INDEX AREA 1 0.1 C B A 5 2X 0.95 1.9 1.45 MAX 3.05 2.75 1.9 2 4 0.5 5X 0.3 0.2 3 (1.1) C A B 0.15 TYP 0.00 0.25 GAGE PLANE 8 TYP 0 0.22 TYP 0.08 0.6 TYP 0.3 SEATING PLANE 4214839/C 04/2017 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Refernce JEDEC MO-178. www.ti.com EXAMPLE BOARD LAYOUT DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X (0.95) 3 4 (R0.05) TYP (2.6) LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:15X SOLDER MASK OPENING METAL SOLDER MASK OPENING METAL UNDER SOLDER MASK EXPOSED METAL EXPOSED METAL 0.07 MIN ARROUND 0.07 MAX ARROUND NON SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED SOLDER MASK DETAILS 4214839/C 04/2017 NOTES: (continued) 4. Publication IPC-7351 may have alternate designs. 5. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X(0.95) 4 3 (R0.05) TYP (2.6) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:15X 4214839/C 04/2017 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 7. Board assembly site may have different recommendations for stencil design. www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2018, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LMH6655MA LMH6655MA/NOPB LMH6655MAX/NOPB LMH6655MM/NOPB LMH6655MMX/NOPB