LTC3412
1
3412fc
For more information www.linear.com/LTC3412
TYPICAL APPLICATION
FEATURES DESCRIPTION
2.5A, 4MHz, Monolithic
Synchronous Step-Down Regulator
The LT C
®
3412 is a high efficiency monolithic synchro-
nous, step-down DC/DC converter utilizing a constant
frequency, current mode architecture. It operates from
an input voltage range of 2.625V to 5.5V and provides
an adjustable regulated output voltage from 0.8V to 5V
while delivering up to 2.5A of output current. The inter-
nal synchronous power switch with 85mΩ on-resistance
increases efficiency and eliminates the need for an external
Schottky diode. Switching frequency is set by an external
resistor or can be sychronized to an external clock. 100%
duty cycle provides low dropout operation extending bat-
tery life in portable systems. OPTI-LOOP
®
compensation
allows the transient response to be optimized over a wide
range of loads and output capacitors.
The LTC3412 can be configured for either Burst Mode
®
operation or forced continuous operation. Forced con-
tinuous operation reduces noise and RF interference
while Burst Mode operation provides high efficiency by
reducing gate charge losses at light loads. In Burst Mode
operation, external control of the burst clamp level allows
the output voltage ripple to be adjusted according to the
requirements of the application. To further maximize bat-
tery life, the P-channel MOSFET is turned on continuously
in dropout (100% duty cycle).
APPLICATIONS
High Efficiency: Up to 95%
2.5A Output Current
Low Quiescent Current: 62µA
Low RDS(ON) Internal Switches: 85mΩ
Programmable Frequency: 300kHz to 4MHz
No Schottky Diode Required
±2% Output Voltage Accuracy
0.8V Reference Allows Low Output Voltage
Selectable Forced Continuous/Burst Mode Operation
with Adjustable Burst Clamp
Synchronizable Switching Frequency
Low Dropout Operation: 100% Duty Cycle
Power Good Output Voltage Monitor
Overtemperature Protection
Available in 16-Lead Thermally Enhanced TSSOP
and QFN Packages
Portable Instruments
Battery-Powered Equipment
Notebook Computers
Distributed Power Systems
Cellular Telephones
Digital Cameras
SVIN PVIN
PGOOD
SW
LTC3412
PGND
SGND
RUN/SS
309k
VIN
2.7V TO 5.5V
1000pF
RT
ITH
VFB
SYNC/MODE
1µH
4.7M
470pF
75k
100pF
100µF
VOUT
2.5V
2.5A
15k
110k 392k
22µF
3412 F01
Figure 1. 2.5V, 2.5A Step-Down Regulator
Efficiency vs Load Current
LOAD CURRENT (A)
0.001
EFFICIENCY (%)
100
80
60
40
20
0
10
3412 G01
VIN = 3.3V
VOUT = 2.5V
Burst Mode OPERATION
FORCED CONTINUOUS
0.1 10.01
L, LT, LTC, LTM, Burst Mode, OPTI-LOOP, Linear Technology and the Linear logo are registered
trademarks and ThinSOT is a trademark of Analog Devices, Inc. All other trademarks are the
property of their respective owners.
LTC3412
2
3412fc
For more information www.linear.com/LTC3412
PIN CONFIGURATION
ABSOLUTE MAXIMUM RATINGS
Input Supply Voltage ....................................0.3V to 6V
ITH, RUN, VFB Voltages ............................... 0.3V to VIN
SYNC/MODE Voltages ................................. 0.3V to VIN
SW Voltage ................................... 0.3V to (VIN + 0.3V)
Peak SW Sink and Source Current ..........................6.5A
(Note 1)
1
2
3
4
5
6
7
8
TOP VIEW
FE PACKAGE
16-LEAD PLASTIC TSSOP
16
15
14
13
12
11
10
9
SVIN
PGOOD
ITH
VFB
RT
SYNC/MODE
RUN/SS
SGND
PVIN
SW
SW
PGND
PGND
SW
SW
PVIN
17
EXPOSED PAD (PIN 17) IS SGND, MUST BE SOLDERED TO PCB
TJMAX = 125°C, θJA = 37.6°C/W, θJC = 10°C/W
16 15 14 13
5678
TOP VIEW
17
UF PACKAGE
16-LEAD (4mm × 4mm) PLASTIC QFN
9
10
11
12
4
3
2
1RUN/SS
SGND
PVIN
SW
PGOOD
SVIN
PVIN
SW
SYNC/MODE
RT
VFB
ITH
SW
PGND
PGND
SW
EXPOSED PAD (PIN 17) IS SGND, MUST BE SOLDERED TO PCB
TJMAX = 125°C, θJA = 34°C/W, θJC = 1°C/W
ORDER INFORMATION
http://www.linear.com/product/LTC3412#orderinfo
LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE
LTC3412EFE#PBF LTC3412EFE#TRPBF 3412EFE 16-Lead Plastic TSSOP –40°C to 125°C
LTC3412IFE#PBF LTC3412IFE#TRPBF 3412IFE 16-Lead Plastic TSSOP –40°C to 125°C
LTC3412EUF#PBF LTC3412EUF#TRPBF 3412 16-Lead (4mm × 4mm) Plastic QFN –40°C to 125°C
LEAD BASED FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE
LTC3412EFE LTC3412EFE#TR 3412EFE 16-Lead Plastic TSSOP –40°C to 125°C
LTC3412IFE LTC3412IFE#TR 3412IFE 16-Lead Plastic TSSOP –40°C to 125°C
LTC3412EUF LTC3412EUF#TR 3412 16-Lead (4mm × 4mm) Plastic QFN –40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/. Some packages are available in 500 unit reels through
designated sales channels with #TRMPBF suffix.
Operating Temperature Range (Note 2)....40°C to 85°C
Storage Temperature Range .................. 65°C to 150°C
Junction Temperature (Note 5) ............................. 125°C
Lead Temperature (Soldering, 10 sec) TSSOP ......300°C
LTC3412
3
3412fc
For more information www.linear.com/LTC3412
ELECTRICAL CHARACTERISTICS
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LTC3412E is guaranteed to meet performance specifications
from 0°C to 85°C. Specifications over the –40°C to 85°C operating
temperature range are assured by design, characterization and correlation
with statistical process controls. The LTC3412I is guaranteed to meet
specified performance over the –40°C to 85°C temperature range.
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
SVIN Signal Input Voltage Range 2.625 5.5 V
VFB Regulated Feedback Voltage (Note 3) l0.784 0.800 0.816 V
IFB Voltage Feedback Leakage Current 0.1 0.4 µA
∆VFB Reference Voltage Line Regulation VIN = 2.7V to 5.5V (Note 3) l0.04 0.2 %V
VLOADREG Output Voltage Load Regulation Measured in Servo Loop, VITH = 0.36V
Measured in Servo Loop, VITH = 0.84V
l
l
0.02
0.02
0.2
–0.2
%
%
∆VPGOOD Power Good Range ±7.5 ±9 %
RPGOOD Power Good Pull-Down Resistance 120 200 Ω
IQInput DC Bias Current
Active Current
Sleep
Shutdown
(Note 4)
VFB = 0.78V, VITH = 1V
VFB = 1V, VITH = 0V
VRUN = 0V, VMODE = 0V
250
62
0.02
330
80
1
µA
µA
µA
fOSC Switching Frequency
Switching Frequency Range
ROSC = 309kΩ
(Note 6)
0.88
0.3
0.95 1.1
4
MHz
MHz
fSYNC SYNC Capture Range (Note 6) 0.3 4 MHz
RPFET RDS(ON) of P-Channel FET ISW = 1A (Note 7) 85 110
RNFET RDS(ON) of N-Channel FET ISW = –1A (Note 7) 65 90
ILIMIT Peak Current Limit 4 5.4 A
VUVLO Undervoltage Lockout Threshold 2.375 2.500 2.625 V
ILSW SW Leakage Current VRUN = 0V, VIN = 5.5V 0.1 1 µA
VRUN RUN Threshold 0.5 0.65 0.8 V
IRUN RUN/SS Leakage Current 1 µA
The denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 3.3V unless otherwise specified.
Note 3: The LTC3412 is tested in a feedback loop that adjusts VFB to
achieve a specified error amplifier output voltage (ITH).
Note 4: Dynamic supply current is higher due to the internal gate charge
being delivered at the switching frequency.
Note 5: TJ is calculated from the ambient temperature TA and power
dissipation as follows: LTC3412: TJ = TA + PD (37.6°C/W).
Note 6: 4MHz operation is guaranteed by design and not production tested.
Note 7: Switch on resistance is guaranteed by design and test correlation
in the UF package and by production test in the FE package.
LTC3412
4
3412fc
For more information www.linear.com/LTC3412
TYPICAL PERFORMANCE CHARACTERISTICS
Efficiency vs Load CurrentEfficiency vs Load Current Efficiency vs Load Current
LOAD CURRENT (A)
0.001
EFFICIENCY (%)
100
80
60
40
20
0
10
3412 G01
VIN = 3.3V
VOUT = 2.5V
Burst Mode OPERATION
FORCED CONTINUOUS
0.1 10.01
100
90
80
70
60
50
40
30
20
10
0
LOAD CURRENT (A)
0.001
EFFICIENCY (%)
10
3412 G02
VOUT = 2.5V
1MHz
Burst Mode OPERATION
0.1 10.01
VIN = 3.3V VIN = 5V
LOAD CURRENT (A)
0.001
EFFICIENCY (%)
100
90
80
70
60
50
40
30
20
10
010
3412 G03
VOUT = 2.5V
1MHz
FORCED CONTINUOUS
0.1 10.01
VIN = 3.3V VIN = 5V
Efficiency vs FrequencyEfficiency vs Input Voltage Load Regulation
Load Step Transient Forced
Continuous
Burst Mode Operation
Load Step Transient Burst Mode
Operation
INPUT VOLTAGE (V)
2.55 3.05 3.55 4.05 4.55 5.05
EFFICIENCY (%)
98
96
94
92
90
88
86
3412 G04
VOUT = 2.5V
1MHz
Burst Mode OPERATION
LOAD = 100mA
LOAD = 1A
LOAD = 2.5A
FREQUENCY (kHz)
300 800 1300 1800 2300 2800 3300 3800
EFFICIENCY (%)
97
96
95
94
93
92
91
3412 G05
VIN = 3.3V
VOUT = 2.5V
LOAD = 1A
Burst Mode OPERATION
1µH
0.47µH
2.2µH
LOAD CURRENT (A)
00.5 1 1.5 2 2.5
%VOUT/VOUT
0.02
0.00
0.02
0.04
0.06
0.08
0.10
0.12
0.14
0.16
0.18
3412 G06
VIN = 3.3V
VOUT = 2.5V
4µs/DIV
VOUT
20mV/DIV
IL
200mA/DIV
3412 G07 20µs/DIV 3412 G08
VOUT
100mV/DIV
IL
1A/DIV
20µs/DIV 3412 G09
VOUT
100mV/DIV
IL
1A/DIV
LTC3412
5
3412fc
For more information www.linear.com/LTC3412
TYPICAL PERFORMANCE CHARACTERISTICS
Start-Up, Burst Mode Operation
Reference Voltage
vs Temperature
Switch On-Resistance
vs Input Voltage
Switch On-Resistance
vs Temperature Switch Leakage vs Input Voltage Frequency vs ROSC
Frequency vs Input Voltage
Switching Frequency
vs Temperature
DC Supply Current
vs Input Voltage
1ms/DIV 3412 G10
VOUT
1V/DIV
VRUN
1V/DIV
IL
1A/DIV
TEMPERATURE (°C)
–45 –25 –5 15 35 55 75 95 115 120
REFERENCE VOLTAGE (V)
3412 G11
0.7960
0.7955
0.7950
0.7945
0.7940
0.7935
0.7930
0.7925
0.7920
VIN = 3.3V
INPUT VOLTAGE (V)
2.5 3 3.5 4 4.5 5
ON-RESISTANCE (mΩ)
3412 G12
120
100
80
60
40
20
0
PFET ON-RESISTANCE
NFET ON-RESISTANCE
TEMPERATURE (°C)
40
–20 0 20 40 60 80 100 120
ON-RESISTANCE (mΩ)
3412 G13
120
110
100
90
80
70
60
50
40
30
20
VIN = 3.3V
PFET ON-RESISTANCE
NFET ON-RESISTANCE
INPUT VOLTAGE (V)
2.5 3 3.5 4 4.5 5 5.5
LEAKAGE CURRENT (nA)
3412 G14
2.5
2.0
1.5
1.0
0.5
0
MAIN SWITCH
SYNCHRONOUS SWITCH
ROSC (kΩ)
50 150 250 350 450 550 650 750 850 950
FREQUENCY (kHz)
3412 G15
4500
4000
3500
3000
2500
2000
1500
1000
500
0
VIN = 3.3V
INPUT VOLTAGE (V)
2.5 3 3.5 4 4.5 5 5.5
FREQUENCY (kHz)
3412 G16
1050
1040
1030
1020
1010
1000
990
R = 309k
TEMPERATURE (°C)
40
–20 0 20 40 60 80 100 120
FREQUENCY (kHz)
3412 G17
1010
1008
1006
1004
1002
1000
998
996
994
992
990
VIN = 3.3V
INPUT VOLTAGE (V)
2.5 3 3.5 4 4.5 5 5.5
DC SUPPLY CURRENT (µA)
3412 G18
350
300
250
200
150
100
50
SLEEP
ACTIVE
LTC3412
6
3412fc
For more information www.linear.com/LTC3412
TYPICAL PERFORMANCE CHARACTERISTICS
DC Supply Current vs Temperature
Minimum Peak Inductor Current
vs Burst Clamp Voltage Current Limit vs Input Voltage
SUPPLY CURRENT (µA)
350
300
250
200
150
100
50
0
TEMPERATURE (°C)
40
–20 0 20 40 60 80 100 120
3412 G19
VIN = 3.3V
ACTIVE
SLEEP
BURST CLAMP VOLTAGE (V)
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
MINIMUM PEAK INDUCTOR CURRENT (mA)
3412 G20
4000
3500
3000
2500
2000
1500
1000
500
0
VIN = 3.3V
INPUT VOLTAGE (V)
2.75
6.8
6.6
6.4
6.2
6.0
5.8
5.6
5.4 4.25 5.25
3412 G21
3.25 3.75 4.75
CURRENT LIMIT (A)
SVIN (Pin 1/Pin 11): Signal Input Supply. Decouple this
pin to SGND with a capacitor. Normally SVIN is equal to
PVIN. SVIN can be greater than PVIN but keep the voltage
difference between S VIN and PVIN less than 0.5V.
PGOOD (Pin 2/Pin 12): Power Good Output. Open-drain
logic output that is pulled to ground when the output volt-
age is not within ±7.5% of regulation point.
ITH (Pin 3/Pin 13): Error Amplifier Compensation Point.
The current comparator threshold increases with this con-
trol voltage. Nominal voltage range for this pin is from
0.2V to 1.4V with 0.2V corresponding to the zero-sense
voltage (zero current).
VFB (Pin 4/Pin 14): Feedback Pin. Receives the feedback
voltage from a resistive divider connected across the
output.
RT (Pin 5/Pin 15): Oscillator Resistor Input. Connecting
a resistor to ground from this pin sets the switching
frequency.
SYNC/MODE (Pin 6/Pin 16): Mode Select and External
Clock Synchronization Input. To select forced continuous,
tie to SVIN. Connecting this pin to a voltage between 0V
and 1V selects Burst Mode operation with the burst clamp
set to the pin voltage.
RUN/SS (Pin 7/Pin 1): Run Control and Soft-Start Input.
Forcing this pin below 0.5V shuts down the LTC3412.
In shutdown all functions are disabled drawing < 1µA of
supply current. A capacitor to ground from this pin sets
the ramp time to full output current.
SGND (Pin 8/Pin 2): Signal Ground. All small-signal com-
ponents, compensation components and the exposed
pad on the bottom side of the IC should connect to this
ground, which in turn connects to PGND at one point.
PVIN (Pins 9, 16/Pins 3, 10): Power Input Supply.
Decouple this pin to PGND with a capacitor.
SW (Pins 10, 11, 14, 15/Pins 4, 5, 8, 9): Switch Node
Connection to the Inductor. This pin connects to the drains
of the internal main and synchronous power MOSFET
switches.
PGND (Pins 12, 13/Pins 6, 7): Power Ground. Connect
this pin close to the (–) terminal of CIN and COUT.
Exposed Pad (Pin 17/Pin 17): Signal Ground. Must be
soldered to PCB for electrical connection and thermal
performance.
PIN FUNCTIONS
(FE/UH Package)
LTC3412
7
3412fc
For more information www.linear.com/LTC3412
FUNCTIONAL BLOCK DIAGRAM
+
2
7
4
+
+
+
0.74V
ERROR
AMPLIFIER
SYNC/MODE BURST
COMPARATOR
BCLAMP
NMOS
CURRENT
COMPARATOR
PMOS CURRENT
COMPARATOR
REVERSE
CURRENT
COMPARATOR
0.86V
RUNRUN/SS
15
13
12
14
11
SW
P-CH
N-CH
10
PGOOD
3
ITH
VFB
0.8V
5
RT
6
SYNC/MODE
3412 FBD
16
PVIN
98
SGND
1
SVIN
SLOPE
COMPENSATION
VOLTAGE
REFERENCE
OSCILLATOR
LOGIC
SLOPE
COMPENSATION
RECOVERY
+
+
+
PGND
+
OPERATION
Main Control Loop
The LTC3412 is a monolithic, constant-frequency, current
mode step-down DC/DC converter. During normal opera-
tion, the internal top power switch (P-channel MOSFET) is
turned on at the beginning of each clock cycle. Current in
the inductor increases until the current comparator trips
and turns off the top power MOSFET. The peak inductor
current at which the current comparator shuts off the top
power switch is controlled by the voltage on the ITH pin.
The error amplifier adjusts the voltage on the ITH pin by
comparing the feedback signal from a resistor divider on
the V
FB
pin with an internal 0.8V reference. When the load
current increases, it causes a reduction in the feedback
voltage relative to the reference. The error amplifier raises
the I
TH
voltage until the average inductor current matches
the new load current. When the top power MOSFET shuts
off, the synchronous power switch (N-channel MOSFET)
turns on until either the bottom current limit is reached or
the beginning of the next clock cycle. The bottom current
limit is set at –2A for forced continuous mode and 0A for
Burst Mode operation.
The operating frequency is set by an external resistor
connected between the RT pin and ground. The practical
switching frequency can range from 300kHz to 4MHz.
LTC3412
8
3412fc
For more information www.linear.com/LTC3412
OPERATION
Overvoltage and undervoltage comparators will pull the
PGOOD output low if the output voltage comes out of
regulation by ±7.5%. In an overvoltage condition, the
top power MOSFET is turned off and the bottom power
MOSFET is switched on until either the overvoltage con-
dition clears or the bottom MOSFETs current limit is
reached.
Forced Continuous Mode
Connecting the SYNC/MODE pin to SV
IN
will disable Burst
Mode operation and force continuous current operation.
At light loads, forced continuous mode operation is less
efficient than Burst Mode operation but may be desirable
in some applications where it is necessary to keep switch-
ing harmonics out of a signal band. The output voltage
ripple is minimized in this mode.
Burst Mode Operation
Connecting the SYNC/MODE pin to a voltage between
0V to 1V enables Burst Mode operation. In Burst Mode
operation, the internal power MOSFETs operate intermit-
tently at light loads. This increases efficiency by minimiz-
ing switching losses. During Burst Mode operation, the
minimum peak inductor current is externally set by the
voltage on the SYNC/MODE pin and the voltage on the
I
TH
pin is monitored by the burst comparator to deter-
mine when sleep mode is enabled and disabled. When the
average inductor current is greater than the load current,
the voltage on the ITH pin drops. As the ITH voltage falls
below 150mV, the burst comparator trips and enables
sleep mode. During sleep mode, the top MOSFET is held
off and the ITH pin is disconnected from the output of the
error amplifier. The majority of the internal circuitry is
also turned off to reduce the quiescent current to 62µA
while the load current is solely supplied by the output
capacitor. When the output voltage drops, the ITH pin is
reconnected to the output of the error amplifier and the
top power MOSFET along with all the internal circuitry is
switched back on. This process repeats at a rate that is
dependent on the load demand.
Pulse skipping operation can be implemented by connect-
ing the SYNC/MODE pin to ground. This forces the burst
clamp level to be at 0V. As the load current decreases, the
peak inductor current will be determined by the voltage
on the ITH pin until the ITH voltage drops below 200mV. At
this point, the peak inductor current is determined by the
minimum on-time of the current comparator. If the load
demand is less than the average of the minimum on-time
inductor current, switching cycles will be skipped to keep
the output voltage in regulation.
Frequency Synchronization
The internal oscillator of the LTC3412 can be synchro-
nized to an external clock connected to the SYNC/MODE
pin. The frequency of the external clock can be in the
range of 300kHz to 4MHz. For this application, the oscil-
lator timing resistor should be chosen to correspond to
a frequency that is 25% lower than the synchronization
frequency. During synchronization, the burst clamp is set
to 0V and each switching cycle begins at the falling edge
of the external clock signal.
Dropout Operation
When the input supply voltage decreases toward the out-
put voltage, the duty cycle increases toward the maximum
on-time. Further reduction of the supply voltage forces
the main switch to remain on for more than one cycle
eventually reaching 100% duty cycle. The output voltage
will then be determined by the input voltage minus the
voltage drop across the internal P-channel MOSFET and
the inductor.
Low Supply Operation
The LTC3412 is designed to operate down to an input sup-
ply voltage of 2.625V. One important consideration at low
input supply voltages is that the RDS(ON) of the P-channel
and N-channel power switches increases. The user should
calculate the power dissipation when the LTC3412 is used
at 100% duty cycle with low input voltages to ensure that
thermal limits are not exceeded.
Slope Compensation and Inductor Peak Current
Slope compensation provides stability in constant fre-
quency architectures by preventing subharmonic oscilla-
tions at duty cycles greater than 50%. It is accomplished
internally by adding a compensating ramp to the inductor
LTC3412
9
3412fc
For more information www.linear.com/LTC3412
OPERATION
APPLICATIONS INFORMATION
current signal at duty cycles in excess of 40%. Normally,
the maximum inductor peak current is reduced when
slope compensation is added. In the LTC3412, however,
slope compensation recovery is implemented to keep the
maximum inductor peak current constant throughout the
range of duty cycles. This keeps the maximum output cur-
rent relatively constant regardless of duty cycle.
Short-Circuit Protection
When the output is shorted to ground, the inductor cur-
rent decays very slowly during a single switching cycle.
To prevent current runaway from occurring, a secondary
current limit is imposed on the inductor current. If the
inductor valley current increases larger than 4.8A, the top
power MOSFET will be held off and switching cycles will
be skipped until the inductor current falls to a safe level.
The basic LTC3412 application circuit is shown in
Figure1. External component selection is determined by
the maximum load current and begins with the selection
of the inductor value and operating frequency followed
by CIN and COUT.
Operating Frequency
Selection of the operating frequency is a tradeoff between
efficiency and component size. High frequency operation
allows the use of smaller inductor and capacitor values.
Operation at lower frequencies improves efficiency by
reducing internal gate charge and switching losses but
requires larger inductance values and/or capacitance to
maintain low output ripple voltage.
The operating frequency of the LTC3412 is determined
by an external resistor that is connected between the RT
pin and ground. The value of the resistor sets the ramp
current that is used to charge and discharge an internal
timing capacitor within the oscillator and can be calcu-
lated by using the following equation:
ROSC =3.2310
11
f(Hz) (Ω)10kΩ
Although frequencies as high as 4MHz are possible, the
minimum on-time of the LTC3412 imposes a minimum
limit on the operating duty cycle. The minimum on-time
is typically 110ns. Therefore, the minimum duty cycle is
equal to 100 • 110ns • f(Hz).
Inductor Selection
For a given input and output voltage, the inductor value
and operating frequency determine the ripple current. The
ripple current ∆I
L
increases with higher V
IN
and decreases
with higher inductance.
ΔIL=VOUT
fL
1VOUT
VIN
Having a lower ripple current reduces the ESR losses
in the output capacitors and the output voltage ripple.
Highest efficiency operation is achieved at low frequency
with small ripple current. This, however, requires a large
inductor.
A reasonable starting point for selecting the ripple current
is ∆IL = 0.4(IMAX). The largest ripple current occurs at the
highest VIN. To guarantee that the ripple current stays
below a specified maximum, the inductor value should
be chosen according to the following equation:
L=VOUT
fΔIL(MAX)
1VOUT
VIN(MAX)
The inductor value will also have an effect on Burst Mode
operation. The transition from low current operation begins
when the peak inductor current falls below a level set by the
burst clamp. Lower inductor values result in higher ripple
current which causes this to occur at lower load currents.
This causes a dip in efficiency in the upper range of low
current operation. In Burst Mode operation, lower induc-
tance values will cause the burst frequency to increase.
LTC3412
10
3412fc
For more information www.linear.com/LTC3412
APPLICATIONS INFORMATION
Inductor Core Selection
Once the value for L is known, the type of inductor must
be selected. High efficiency converters generally cannot
afford the core loss found in low cost powdered iron
cores, forcing the use of more expensive ferrite, mol-
lypermalloy, or Kool Mµ
®
cores. Actual core loss is inde-
pendent of core size for a fixed inductor value but it is very
dependent on the inductance selected. As the inductance
increases, core losses decrease. Unfortunately, increased
inductance requires more turns of wire and therefore cop-
per losses will increase.
Ferrite designs have very low core losses and are pre-
ferred at high switching frequencies, so design goals can
concentrate on copper loss and preventing saturation.
Ferrite core material saturates “hard,” which means that
inductance collapses abruptly when the peak design cur-
rent is exceeded. This results in an abrupt increase in
inductor ripple current and consequent output voltage
ripple. Do not allow the core to saturate!
Different core materials and shapes will change the
size/current and price/current relationship of an induc-
tor. Toroid or shielded pot cores in ferrite or permalloy
materials are small and don’t radiate energy but generally
cost more than powdered iron core inductors with similar
characteristics. The choice of which style inductor to use
mainly depends on the price vs size requirements and any
radiated field/EMI requirements. New designs for surface
mount inductors are available from Coiltronics, Coilcraft,
Toko and Sumida.
CIN and COUT Selection
The input capacitance, C
IN
, is needed to filter the trapezoi-
dal current at the source of the top MOSFET. To prevent
large ripple voltage, a low ESR input capacitor sized for
the maximum RMS current should be used. RMS current
is given by:
IRMS =IOUT(MAX)
VOUT
VIN
VIN
VOUT
1
This formula has a maximum at VIN = 2VOUT, where IRMS
= IOUT/2. This simple worst-case condition is commonly
used for design because even significant deviations do
not offer much relief. Note that ripple current ratings from
capacitor manufacturers are often based on only 2000
hours of life which makes it advisable to further derate the
capacitor, or choose a capacitor rated at a higher tempera-
ture than required. Several capacitors may also be paral-
leled to meet size or height requirements in the design.
The selection of COUT is determined by the effective series
resistance (ESR) that is required to minimize voltage rip-
ple and load step transients, as well as the amount of bulk
capacitance that is necessary to ensure that the control
loop is stable. Loop stability can be checked by viewing
the load transient response as described in a later section.
The output ripple, ∆VOUT, is determined by:
ΔVOUT ΔILESR+1
8fCOUT
The output ripple is highest at maximum input voltage
since ∆IL increases with input voltage. Multiple capacitors
placed in parallel may be needed to meet the ESR and
RMS current handling requirements. Dry tantalum, spe-
cial polymer, aluminum electrolytic and ceramic capaci-
tors are all available in surface mount packages. Special
polymer capacitors offer very low ESR but have lower
capacitance density than other types. Tantalum capacitors
have the highest capacitance density but it is important
to only use types that have been surge tested for use in
switching power supplies. Aluminum electrolytic capaci-
tors have significantly higher ESR but can be used in cost-
sensitive applications provided that consideration is given
to ripple current ratings and long term reliability. Ceramic
capacitors have excellent low ESR characteristics but can
have a high voltage coefficient and audible piezoelectric
effects. The high Q of ceramic capacitors with trace induc-
tance can also lead to significant ringing.
Using Ceramic Input and Output Capacitors
Higher values, lower cost ceramic capacitors are now
becoming available in smaller case sizes. Their high ripple
current, high voltage rating and low ESR make them ideal
for switching regulator applications. However, care must
be taken when these capacitors are used at the input and
output. When a ceramic capacitor is used at the input and
LTC3412
11
3412fc
For more information www.linear.com/LTC3412
APPLICATIONS INFORMATION
the power is supplied by a wall adapter through long wires,
a load step at the output can induce ringing at the input,
VIN. At best, this ringing can couple to the output and be
mistaken as loop instability. At worst, a sudden inrush
of current through the long wires can potentially cause
a voltage spike at VIN large enough to damage the part.
Output Voltage Programming
The output voltage is set by an external resistive divider
according to the following equation:
VOUT =0.8V 1+
R2
R1
The resistive divider allows the V
FB
pin to sense a fraction
of the output voltage as shown in Figure 2.
LTC3412
VFB
VOUT
SGND
3412 F02
R2
R1
Figure 2. Setting the Output Voltage
Burst Clamp Programming
If the voltage on the SYNC/MODE pin is less than VIN by
1V, Burst Mode operation is enabled. During Burst Mode
operation, the voltage on the SYNC/MODE pin determines
the burst clamp level which sets the minimum peak induc-
tor current, IBURST, for each switching cycle according to
the following equation:
IBURST =VBURST 0.2V
( )
3.75A
0.8V
VBURST is the voltage on the SYNC/MODE pin. IBURST can
be programmed in the range of 0A to 3.75A. For values
of VBURST greater than 1V, IBURST is set at 3.75A. For
values of VBURST less than 0.2V, IBURST is set at 0A. As
the output load current drops, the peak inductor current
decreases to keep the output voltage in regulation. When
the output load current demands a peak inductor current
that is less than I
BURST
, the burst clamp will force the peak
inductor current to remain equal to IBURST regardless of
further reductions in the load current. Since the average
inductor current is greater than the output load current,
the voltage on the ITH pin will decrease. When the ITH
voltage drops to 150mV, sleep mode is enabled in which
both power MOSFETs are shut off along with most of the
circuitry to minimize power consumption. All circuitry is
turned back on and the power MOSFETs begin switching
again when the output voltage drops out of regulation.
The value for IBURST is determined by the desired amount
of output voltage ripple. As the value of IBURST increases,
the sleep period between pulses and the output voltage
ripple increase. The burst clamp voltage, VBURST, can be
set by a resistor divider from the VFB pin to the SGND pin
as shown in Figure 1.
Pulse skipping, which is a compromise between low
output voltage ripple and efficiency, can be implemented
by connecting the SYNC/MODE pin to ground. This sets
IBURST to 0A. In this condition, the peak inductor current is
limited by the minimum on-time of the current comparator,
and the lowest output voltage ripple is achieved while still
operating discontinuously. During very light output loads,
pulse skipping allows only a few switching cycles to be
skipped while maintaining the output voltage in regulation.
Frequency Synchronization
The LTC3412s internal oscillator can be synchronized
to an external clock signal. During synchronization, the
top MOSFET turn-on is locked to the falling edge of the
external frequency source. The synchronization frequency
range is 300kHz to 4MHz. Synchronization only occurs
if the external frequency is greater than the frequency
set by the external resistor. Because slope compensation
is generated by the oscillators RC circuit, the external
frequency should be set 25% higher than the frequency
set by the external resistor to ensure that adequate slope
compensation is present.
Soft-Start
The RUN/SS pin provides a means to shut down the
LTC3412 as well as a timer for soft-start. Pulling the RUN/
SS pin below 0.5V places the LTC3412 in a low quiescent
current shutdown state (IQ < 1µA).
LTC3412
12
3412fc
For more information www.linear.com/LTC3412
APPLICATIONS INFORMATION
The LTC3412 contains an internal soft-start clamp that
gradually raises the clamp on ITH after the RUN/SS pin is
pulled above 2V. The full current range becomes available
on ITH after 1024 switching cycles. If a longer soft-start
period is desired, the clamp on ITH can be set externally
with a resistor and capacitor on the RUN/SS pin as shown
in Figure 1. The soft-start duration can be calculated by
using the following formula:
tSS =RSSCSS ln VIN
VIN 1.8V
Seconds
( )
Efficiency Considerations
The efficiency of a switching regulator is equal to the out-
put power divided by the input power times 100%. It is
often useful to analyze individual losses to determine what
is limiting the efficiency and which change would produce
the most improvement. Efficiency can be expressed as:
Efficiency = 100% – (L1 + L2 + L3 + ...)
where L1, L2, etc. are the individual losses as a percent-
age of input power.
Although all dissipative elements in the circuit produce
losses, two main sources usually account for most of the
losses: VIN quiescent current and I2R losses.
The VIN quiescent current loss dominates the efficiency
loss at very low load currents whereas the I2R loss domi-
nates the efficiency loss at medium to high load currents.
In a typical efficiency plot, the efficiency curve at very low
load currents can be misleading since the actual power
lost is of no consequence.
1. The VIN quiescent current is due to two components:
the DC bias current as given in the electrical characteris-
tics and the internal main switch and synchronous switch
gate charge currents. The gate charge current results
from switching the gate capacitance of the internal power
MOSFET switches. Each time the gate is switched from
high to low to high again, a packet of charge dQ moves
from VIN to ground. The resulting dQ/dt is the current
out of VIN that is typically larger than the DC bias current.
In continuous mode, IGATECHG=f(QT + QB) where QT and
QB are the gate charges of the internal top and bottom
switches. Both the DC bias and gate charge losses are
proportional to V
IN
and thus their effects will be more
pronounced at higher supply voltages.
2. I2R losses are calculated from the resistances of the
internal switches, RSW and external inductor RL. In con-
tinuous mode the average output current flowing through
inductor L is “chopped” between the main switch and the
synchronous switch. Thus, the series resistance looking
into the SW pin is a function of both top and bottom
MOSFET RDS(ON) and the duty cycle (DC) as follows:
RSW = (RDS(ON)TOP)(DC) + (RDS(ON)BOT)(1 – DC)
The RDS(ON) for both the top and bottom MOSFETs can
be obtained from the Typical Performance Characteristics
curves. Thus, to obtain I
2
R losses, simply add R
SW
to
RL and multiply the result by the square of the average
output current.
Other losses including CIN and COUT ESR dissipative
losses and inductor core losses generally account for
less than 2% of the total loss.
Thermal Considerations
In most applications, the LTC3412 does not dissipate
much heat due to its high efficiency. But, in applications
where the LTC3412 is running at high ambient tempera-
ture with low supply voltage and high duty cycles, such
as in dropout, the heat dissipated may exceed the maxi-
mum junction temperature of the part. If the junction
temperature reaches approximately 150°C, both power
switches will be turned off and the SW node will become
high impedance.
To avoid the LTC3412 from exceeding the maximum junc-
tion temperature, the user will need to do some thermal
analysis. The goal of the thermal analysis is to determine
whether the power dissipated exceeds the maximum junc-
tion temperature of the part. The temperature rise is given
by:
TR = (PD)(θJA)
where P
D
is the power dissipated by the regulator and θ
JA
is the thermal resistance from the junction of the die to
the ambient temperature.
LTC3412
13
3412fc
For more information www.linear.com/LTC3412
APPLICATIONS INFORMATION
The junction temperature, TJ, is given by:
TJ = TA + TR
where TA is the ambient temperature.
As an example, consider the LTC3412 in dropout at an
input voltage of 3.3V, a load current of 2.5A and an ambi-
ent temperature of 70°C. From the typical performance
graph of switch resistance, the RDS(ON) of the P-channel
switch at 70°C is approximately 97mΩ. Therefore, power
dissipated by the part is:
PD = (ILOAD2)(RDS(ON)) = (2.5A)2(97mΩ) = 0.61W
For the TSSOP package, the θJA is 37.6°C/W. Thus the
junction temperature of the regulator is:
TJ = 70°C + (0.61W)(37.6°C/W) = 93°C
which is below the maximum junction temperature of
125°C.
Note that at higher supply voltages, the junction tempera-
ture is lower due to reduced switch resistance (RDS(ON)).
Checking Transient Response
The regulator loop response can be checked by look-
ing at the load transient response. Switching regulators
take several cycles to respond to a step in load current.
When a load step occurs, VOUT immediately shifts by an
amount equal to ∆ILOAD(ESR), where ESR is the effective
series resistance of COUT. ∆ILOAD also begins to charge or
discharge COUT generating a feedback error signal used
by the regulator to return VOUT to its steady-state value.
During this recovery time, VOUT can be monitored for
overshoot or ringing that would indicate a stability prob-
lem. The ITH pin external components and output capaci-
tor shown in Figure 1 will provide adequate compensation
for most applications.
Design Example
As a design example, consider using the LTC3412 in an
application with the following specifications: VIN = 2.7V to
4.2V, VOUT = 2.5V, IOUT(MAX) = 2.5A, IOUT(MIN) = 10mA, f
= 1MHz. Because efficiency is important at both high and
low load current, Burst Mode operation will be utilized.
First, calculate the timing resistor:
ROSC =3.2310
11
1•10
610k =313k
Use a standard value of 309k. Next, calculate the inductor
value for about 40% ripple current at maximum VIN:
L=2.5V
(1MHz)(1A)
12.5V
4.2V
=1.01µH
Using a 1µH inductor, results in a maximum ripple cur-
rent of:
ΔIL=2.5V
(1MHz)(1µH)
12.5V
4.2V
=1.01A
COUT will be selected based on the ESR that is required to
satisfy the output voltage ripple requirement and the bulk
capacitance needed for loop stability. In this application,
two tantalum capacitors will be used to provide the bulk
capacitance and a ceramic capacitor in parallel to lower
the total effective ESR. For this design, two 100µF tanta-
lum capacitors in parallel with a 10µF ceramic capacitor
will be used. CIN should be sized for a maximum current
rating of:
IRMS=2.5A
( )
2.5V
4.2V
4.2V
2.5V 1=1.23ARMS
Decoupling the PVIN and SVIN pins with a 22µF ceramic
capacitor and a 220µF tantalum capacitor is adequate for
most applications.
The burst clamp and output voltage can now be pro-
grammed by choosing the values of R1, R2 and R3. The
voltage on the MODE pin will be set to 0.32V by the resis-
tor divider consisting of R2 and R3. A burst clamp voltage
of 0.32V will set the minimum inductor current, IBURST,
as follows:
IBURST=0.32V 0.2V
( )
3.75V
0.8V
=563mA
LTC3412
14
3412fc
For more information www.linear.com/LTC3412
If we set the sum of R2 and R3 to 185k, then the following
equations can be solved:
R2
+
R3
=
185k
1+R2
R3
=0.8V
0.32V
The last two equations shown result in the following val-
ues for R2 and R3: R2 = 110k , R3 = 75k. The value of R1
can now be determined by solving the equation shown
below:
1+
R1
185k =
2.5V
0.8V
R1=393k
A value of 392k will be selected for R1. Figure 4 shows
the complete schematic for this design example.
PC Board Layout Checklist
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of
the LTC3412. Check the following in your layout.
APPLICATIONS INFORMATION
1. A ground plane is recommended. If a ground plane
layer is not used, the signal and power grounds should be
segregated with all small-signal components returning to
the SGND pin at one point which is then connected to the
PGND pin close to the LTC3412. The exposed pad should
be connected to SGND.
2. Connect the (+) terminal of the input capacitor(s), CIN,
as close as possible to the PVIN pin. This capacitor pro-
vides the AC current into the internal power MOSFETs.
3. Keep the switching node, SW, away from all sensitive
small-signal nodes.
4. Flood all unused areas on all layers with copper.
Flooding with copper will reduce the temperature rise of
power components. You can connect the copper areas to
any DC net (PVIN, SVIN, VOUT, PGND, SGND, or any other
DC rail in your system).
5. Connect the VFB pin directly to the feedback resistors.
The resistor divider must be connected between VOUT and
SGND.
Figure 3. LTC3412 Layout Diagram
Top Side Bottom Side
LTC3412
15
3412fc
For more information www.linear.com/LTC3412
APPLICATIONS INFORMATION
8SGND
CSS
470pF X7R
CC
100pF
*
**
††
TOKO D62CB A920CY-1ROM
SANYO POSCAP 4TPB100M
TAIYO YUDEN LMK325BJ106MN
SANYO POSCAP 2R5TPC220M
7
RSS
4.7M RUN
6SYNC/MODE
ROSC
309k
5RT
R2
110k
4
R3
75k
VFB
RITH
7.15k 3
CITH 680pF X7R
ITH
2PGOODPGOOD
1SVIN
9
PVIN
10
SW
11
SW
12
PGND
LTC3412 13 L1*
1µH
PGND
14
SW
15
SW
16
PVIN
CIN2
22µF
X5R 6.3V
CIN1††
220µF
COUT2
10µF
COUT1**
100µF
×2
VOUT
2.5V
2.5A
VIN
2.7V TO 4.2V
GND
3412 F04
R1 392k
+
RPG
100k
CFB 22pF X5R
Figure 4. Single Lithium-Ion to 2.5V, 2.5A Regulator at 1MHz, Burst Mode Operation Using POSCAPs
LTC3412
16
3412fc
For more information www.linear.com/LTC3412
TYPICAL APPLICATIONS
2.5V, 2.5A Regulator Using All Ceramic Capacitors
1.8V, 2.5A Step-Down Regulator at 1MHz, Burst Mode Operation
8SGND
CSS
470pF X7R
7
RSS
4.7M RUN
6SYNC/MODE
ROSC
309k
5RT
R2
110k
4
R3
75k
VFB
RITH
15k 3
CITH 1000pF X7R
ITH
2PGOODPGOOD
1SVIN
9
PVIN
10
SW
11
SW
12
PGND
LTC3412 13 L1*
1µH
PGND
14
SW
15
SW
16
PVIN
C1 22pF X5R
CIN2
22µF
X5R 6.3V
CIN1
22µF
X5R 6.3V
COUT**
100µF
VOUT
2.5V
2.5A
VIN
2.7V TO 5.5V
GND
3412 F05
CIN3**
100µF
R1 392k
*
**
TOKO D62CB A920CY-1ROM
TDK C4532X5R0J107M
CC
100pF
RPG
100k
8SGND
CSS
470pF X7R
7
RSS
4.7M RUN
6SYNC/MODE
ROSC
309k
5RT
R2
110k
R3
75k
4VFB
RITH
10k 3
CITH 560pF X7R
ITH
2PGOODPGOOD
1SVIN
9
PVIN
10
SW
11
SW
12
PGND
LTC3412 13
PGND
14
SW
15
SW
16
PVIN
CIN2
22µF**
CIN1**
22µF
COUT**
22µF
x2
VOUT
1.8V
2A
VIN
3.3V
GND
R1 232k
3412 TA05
L1
1µH*
*
**
SUMIDA CR431R0
AVX 12066D226MAT
C2
47pF
C1 22pF X5R
RPG
100k
LTC3412
17
3412fc
For more information www.linear.com/LTC3412
TYPICAL APPLICATIONS
2.5V, 2.5A Low Output Noise Regulator at 2MHz
Efficiency vs Load Current
2MHz, Low Noise
8SGND
CSS
470pF X7R
7
RSS
4.7M
RUN
6SYNC/MODE
ROSC
137k
5RT
R2
182k
4VFB
RITH
22.1k 3
CITH 1000pF X7R
ITH
2PGOODPGOOD
1SVIN
9
PVIN
10
SW
11
SW
12
PGND
LTC3412 13
PGND
14
SW
15
SW
16
PVIN
CIN2
100µF**
CIN1**
100µF
COUT**
100µF
×2
VOUT
2.5V
2.5A
VIN
3.3V
GND
R1 392k
RIN
3412 TA06
L1
0.47µH*
*
**
VISHAY DALE IHLP-2525CZ-01 0.47
TDK C4532X5R0J107M
C1
56pF
CFF 22pF X7R
RPG
100k
CIN3
0.1µF
X5R
LOAD CURRENT (A)
0.01
40
EFFICIENCY (%)
50
60
70
80
0.1 1 10
30
20
10
0
90
100
LTC3412
18
3412fc
For more information www.linear.com/LTC3412
TYPICAL APPLICATIONS
8SGND
CSS
470pF X7R
7
RSS
4.7M
RUN
6SYNC/MODE
ROSC
309k
5RT
R2
200k
4
VFB
RITH
15k 3
CITH 1000pF X7R
ITH
2PGOODPGOOD
1SVIN
9
PVIN
10
SW
11
SW
12
PGND
LTC3412 13
PGND
14
SW
15
SW
16
PVIN
CIN2
22µF
X5R 6.3V
CIN1
22µF
X5R 6.3V
COUT**
100µF
VOUT
3.3V
2.5A
VIN
5V
GND
R1 634k
3412 TA01
L1*
1µH
*
**
PULSE P1166.162T
TDK C4532X5R0J107M
CC
100pF
C1 22pF X5R
CIN3**
100µF
RPG
100k
8SGND
CSS
470pF X7R
7
RSS
4.7M RUN
6SYNC/MODE
ROSC
309k
5RT
R2
110k
4
R3
75k
VFB
RITH
15k 3
CITH 1000pF X7R
ITH
2PGOODPGOOD
1SVIN
9
PVIN
10
SW
11
SW
12
PGND
LTC3412 13 L1*
2µH
M1
SILICONIX
Si2302DS
D1
DIODES, INC.
B320A
PGND
14
SW
15
SW
16
PVIN
C1
22pF
CIN2
22µF
X5R 6.3V
CIN1
22µF
X5R 6.3V
COUT**
100µF
VOUT
3.3V
VIN
2.7V TO 4.2V
GND
GND
3412 F04
CIN3**
100µF
×2
R1 576k
*
**
TOKO D63CB
TDK C4532X5R0J107M
C2
100pF
RPG
100k
VIN MAXIMUM IOUT
2.7V 800mA
3V 900mA
3.5V 1.05A
4.2V 1.2A
3.3V, 2.5A Step-Down Regulator at 1MHz, Forced Continuous Mode Operation
Lithium-Ion to 3.3V, Single Inductor Buck-Boost Converter
LTC3412
19
3412fc
For more information www.linear.com/LTC3412
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/product/LTC3412#packaging for the most recent package drawings.
FE16 (BA) TSSOP REV L 0117
0.09 – 0.20
(.0035 – .0079)
0° – 8°
0.25
REF
0.50 – 0.75
(.020 – .030)
4.30 – 4.50*
(.169 – .177)
1 3 4 5678
10 9
4.90 – 5.10*
(.193 – .201)
16 1514 13 12 11
1.10
(.0433)
MAX
0.05 – 0.15
(.002 – .006)
0.65
(.0256)
BSC
2.74
(.108)
2.74
(.108)
0.195 – 0.30
(.0077 – .0118)
TYP
2
MILLIMETERS
(INCHES) *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.150mm (.006") PER SIDE
NOTE:
1. CONTROLLING DIMENSION: MILLIMETERS
2. DIMENSIONS ARE IN
RECOMMENDED SOLDER PAD LAYOUT
3. DRAWING NOT TO SCALE
0.45 ±0.05
0.65 BSC
4.50 ±0.10
6.60 ±0.10
1.05 ±0.10
2.74
(.108)
2.74
(.108)
SEE NOTE 4
4. RECOMMENDED MINIMUM PCB METAL SIZE
FOR EXPOSED PAD ATTACHMENT
6.40
(.252)
BSC
FE Package
16-Lead Plastic TSSOP (4.4mm)
(Reference LTC DWG # 05-08-1663 Rev L)
Exposed Pad Variation BA
LTC3412
20
3412fc
For more information www.linear.com/LTC3412
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/product/LTC3412#packaging for the most recent package drawings.
4.00 ±0.10
(4 SIDES)
NOTE:
1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE MO-220 VARIATION (WGGC)
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
PIN 1
TOP MARK
(NOTE 6)
0.55 ±0.20
1615
1
2
BOTTOM VIEW—EXPOSED PAD
2.15 ±0.10
(4-SIDES)
0.75 ±0.05 R = 0.115
TYP
0.30 ±0.05
0.65 BSC
0.200 REF
0.00 – 0.05
(UF16) QFN 10-04
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
0.72 ±0.05
0.30 ±0.05
0.65 BSC
2.15 ±0.05
(4 SIDES)
2.90 ±0.05
4.35 ±0.05
PACKAGE OUTLINE
PIN 1 NOTCH R = 0.20 TYP
OR 0.35 × 45° CHAMFER
UF Package
16-Lead Plastic QFN (4mm × 4mm)
(Reference LTC DWG # 05-08-1692 Rev Ø)
LTC3412
21
3412fc
For more information www.linear.com/LTC3412
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
REVISION HISTORY
REV DATE DESCRIPTION PAGE NUMBER
C 05/17 Add Storage Temperature to Absolute Maximum Ratings 2
(Revision history begins at Rev C)
LTC3412
22
3412fc
LINEAR TECHNOLOGY CORPORATION 2002
LT 0517 REV C • PRINTED IN USA
www.linear.com/LTC3412
RELATED PARTS
TYPICAL APPLICATION
PART NUMBER DESCRIPTION COMMENTS
LTC1701/LTC1701B 700mA (IOUT), 1MHz Step-Down Converter VIN = 2.5V to 5V, B Version: Burst Mode Defeat, ThinSOT™
LTC1772/LTC1772B Constant 550kHz Current Mode Step-Down DC/DC Controller VIN = 2.5V to 9.8V, 94% Efficiency, 100% Duty Cycle, ThinSOT
LTC1773 Constant Frequency 550kHz Step-Down DC/DC Controller VIN = 2.65V to 8.5V, 95% Efficiency,
VOUT from 0.8V to VIN, MSOP-10
LTC1875 1.5A (IOUT), 500kHz Synchronous Step-Down Converter VIN = 2.65V to 6V, 95% Efficiency, PLL, SSOP-16
LTC1877 600mA (IOUT), 500kHz Synchronous Step-Down Converter VIN = 2.65V to 10V, 95% Efficiency, MSOP-8
LTC1878 600mA (IOUT), 550kHz Synchronous Step-Down Converter VIN = 2.65V to 6V, 95% Efficiency, MSOP-8
LTC1879 1.2A (IOUT), 550kHz Synchronous Step-Down Converter VIN = 2.65V to 10V, 95% Efficiency, SSOP-16
LTC3404 600mA (IOUT), 1.4MHz Synchronous Step-Down Converter VIN = 2.65V to 6V, 95% Efficiency, MSOP-8
LTC3405A 300mA (IOUT), 1.5MHz Synchronous Step-Down Converter VIN = 2.65V to 6V, 96% Efficiency, ThinSOT Package
LTC3406/LTC3406B 600mA (IOUT), 1.5MHz Synchronous Step-Down Converter VIN = 2.5V to 5.5V, 95% Efficiency,
ThinSOT, B Version: Burst Mode Defeat
LTC3411 1.25A (IOUT), 4MHz Synchronous Step-Down Converter VIN = 2.5V to 5.5V, 95% Efficiency, MSOP-10
8SGND
CSS
470pF X7R
7
RSS
4.7M RUN
6SYNC/MODE
1.25MHz
EXT CLOCK
ROSC 309k
5RT
R2 182k
4VFB
RITH
15k
RPG
100k
3
CITH 1000pF X7R
ITH
2PGOODPGOOD
1SVIN
9
PVIN
10
SW
11
SW
12
PGND
LTC3412 13 L1*
1µH
PGND
14
SW
15
SW
16
PVIN
CIN2
22µF
X5R 6.3V
CIN1
22µF
X5R 6.3V
COUT1**
100µF
VOUT
2.5V
2.5A
VIN
2.7V TO 5.5V
GND
R1 392k
3412 TA02
*
**
TOKO D62CB A920CY-1ROM
TDK C4532X5R0J107M
CC 100pF
C1 22pF X5R
CIN3**
100µF
2.5V, 2.5A Step-Down Regulator Synchronized to 1.25MHz