LTC3412 2.5A, 4MHz, Monolithic Synchronous Step-Down Regulator FEATURES DESCRIPTION The LTC(R)3412 is a high efficiency monolithic synchronous, step-down DC/DC converter utilizing a constant frequency, current mode architecture. It operates from an input voltage range of 2.625V to 5.5V and provides an adjustable regulated output voltage from 0.8V to 5V while delivering up to 2.5A of output current. The internal synchronous power switch with 85m on-resistance increases efficiency and eliminates the need for an external Schottky diode. Switching frequency is set by an external resistor or can be sychronized to an external clock. 100% duty cycle provides low dropout operation extending battery life in portable systems. OPTI-LOOP(R) compensation allows the transient response to be optimized over a wide range of loads and output capacitors. High Efficiency: Up to 95% 2.5A Output Current Low Quiescent Current: 62A Low RDS(ON) Internal Switches: 85m Programmable Frequency: 300kHz to 4MHz No Schottky Diode Required 2% Output Voltage Accuracy 0.8V Reference Allows Low Output Voltage Selectable Forced Continuous/Burst Mode Operation with Adjustable Burst Clamp Synchronizable Switching Frequency Low Dropout Operation: 100% Duty Cycle Power Good Output Voltage Monitor Overtemperature Protection Available in 16-Lead Thermally Enhanced TSSOP and QFN Packages The LTC3412 can be configured for either Burst Mode(R) operation or forced continuous operation. Forced continuous operation reduces noise and RF interference while Burst Mode operation provides high efficiency by reducing gate charge losses at light loads. In Burst Mode operation, external control of the burst clamp level allows the output voltage ripple to be adjusted according to the requirements of the application. To further maximize battery life, the P-channel MOSFET is turned on continuously in dropout (100% duty cycle). APPLICATIONS Portable Instruments Battery-Powered Equipment Notebook Computers Distributed Power Systems Cellular Telephones Digital Cameras L, LT, LTC, LTM, Burst Mode, OPTI-LOOP, Linear Technology and the Linear logo are registered trademarks and ThinSOT is a trademark of Analog Devices, Inc. All other trademarks are the property of their respective owners. TYPICAL APPLICATION Efficiency vs Load Current VIN 2.7V TO 5.5V RT PGOOD 309k 4.7M 1H SW LTC3412 470pF SGND 15k 1000pF 100F PGND RUN/SS 100pF ITH SYNC/MODE VFB 110k 100 22F PVIN 392k VOUT 2.5V 2.5A 80 EFFICIENCY (%) SVIN Burst Mode OPERATION 60 FORCED CONTINUOUS 40 20 3412 F01 75k 0 0.001 Figure 1. 2.5V, 2.5A Step-Down Regulator For more information www.linear.com/LTC3412 VIN = 3.3V VOUT = 2.5V 0.01 0.1 1 LOAD CURRENT (A) 10 3412 G01 3412fc 1 LTC3412 ABSOLUTE MAXIMUM RATINGS (Note 1) Input Supply Voltage..................................... - 0.3V to 6V ITH, RUN, VFB Voltages................................ -0.3V to VIN SYNC/MODE Voltages.................................. -0.3V to VIN SW Voltage.................................... -0.3V to (VIN + 0.3V) Peak SW Sink and Source Current ...........................6.5A Operating Temperature Range (Note 2)....-40C to 85C Storage Temperature Range................... -65C to 150C Junction Temperature (Note 5).............................. 125C Lead Temperature (Soldering, 10 sec) TSSOP....... 300C PIN CONFIGURATION 16 PVIN 2 15 SW ITH 3 14 SW VFB 4 13 PGND RUN/SS 1 RT 5 12 PGND SGND 2 SYNC/MODE 6 11 SW PVIN 3 RUN/SS 7 10 SW SW 4 EXPOSED PAD (PIN 17) IS SGND, MUST BE SOLDERED TO PCB TJMAX = 125C, JA = 37.6C/W, JC = 10C/W ORDER INFORMATION 10 PVIN 6 7 8 SW 9 5 PVIN FE PACKAGE 16-LEAD PLASTIC TSSOP 11 SVIN 17 PGND 9 12 PGOOD SW 8 16 15 14 13 PGND SGND 17 ITH 1 VFB SYNC/MODE SVIN PGOOD RT TOP VIEW TOP VIEW SW UF PACKAGE 16-LEAD (4mm x 4mm) PLASTIC QFN EXPOSED PAD (PIN 17) IS SGND, MUST BE SOLDERED TO PCB TJMAX = 125C, JA = 34C/W, JC = 1C/W http://www.linear.com/product/LTC3412#orderinfo LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3412EFE#PBF LTC3412EFE#TRPBF 3412EFE 16-Lead Plastic TSSOP -40C to 125C LTC3412IFE#PBF LTC3412IFE#TRPBF 3412IFE 16-Lead Plastic TSSOP -40C to 125C LTC3412EUF#PBF LTC3412EUF#TRPBF 3412 16-Lead (4mm x 4mm) Plastic QFN -40C to 125C LEAD BASED FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3412EFE LTC3412EFE#TR 3412EFE 16-Lead Plastic TSSOP -40C to 125C LTC3412IFE LTC3412IFE#TR 3412IFE 16-Lead Plastic TSSOP -40C to 125C LTC3412EUF LTC3412EUF#TR 3412 16-Lead (4mm x 4mm) Plastic QFN -40C to 125C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/. Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix. 2 3412fc For more information www.linear.com/LTC3412 LTC3412 ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VIN = 3.3V unless otherwise specified. SYMBOL PARAMETER SVIN Signal Input Voltage Range VFB Regulated Feedback Voltage IFB Voltage Feedback Leakage Current VFB Reference Voltage Line Regulation VLOADREG Output Voltage Load Regulation CONDITIONS MIN 0.1 0.4 A 0.04 0.2 %V Measured in Servo Loop, VITH = 0.36V Measured in Servo Loop, VITH = 0.84V l l 0.02 - 0.02 0.2 -0.2 % % 7.5 9 % 120 200 250 62 0.02 330 80 1 A A A 0.95 1.1 4 MHz MHz 4 MHz 85 110 m 65 90 m Power Good Pull-Down Resistance Input DC Bias Current Active Current Sleep Shutdown (Note 4) VFB = 0.78V, VITH = 1V VFB = 1V, VITH = 0V VRUN = 0V, VMODE = 0V fOSC Switching Frequency Switching Frequency Range ROSC = 309k (Note 6) 0.88 0.3 0.3 fSYNC SYNC Capture Range (Note 6) RPFET RDS(ON) of P-Channel FET ISW = 1A (Note 7) RNFET RDS(ON) of N-Channel FET ISW = -1A (Note 7) ILIMIT Peak Current Limit VUVLO Undervoltage Lockout Threshold IRUN RUN/SS Leakage Current V l IQ SW Leakage Current V 0.816 VIN = 2.7V to 5.5V (Note 3) RPGOOD RUN Threshold 5.5 0.800 2.625 0.784 UNITS l Power Good Range ILSW MAX (Note 3) VPGOOD VRUN TYP 4 5.4 2.375 2.500 0.5 VRUN = 0V, VIN = 5.5V Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC3412E is guaranteed to meet performance specifications from 0C to 85C. Specifications over the - 40C to 85C operating temperature range are assured by design, characterization and correlation with statistical process controls. The LTC3412I is guaranteed to meet specified performance over the -40C to 85C temperature range. A 2.625 V 0.1 1 A 0.65 0.8 V 1 A Note 3: The LTC3412 is tested in a feedback loop that adjusts VFB to achieve a specified error amplifier output voltage (ITH). Note 4: Dynamic supply current is higher due to the internal gate charge being delivered at the switching frequency. Note 5: TJ is calculated from the ambient temperature TA and power dissipation as follows: LTC3412: TJ = TA + PD (37.6C/W). Note 6: 4MHz operation is guaranteed by design and not production tested. Note 7: Switch on resistance is guaranteed by design and test correlation in the UF package and by production test in the FE package. 3412fc For more information www.linear.com/LTC3412 3 LTC3412 TYPICAL PERFORMANCE CHARACTERISTICS Efficiency vs Load Current Efficiency vs Load Current 100 100 90 90 80 60 FORCED CONTINUOUS 40 20 0 0.001 50 40 30 10 0.01 0.1 1 LOAD CURRENT (A) 3412 G01 Efficiency vs Input Voltage 0.01 0.1 1 LOAD CURRENT (A) LOAD = 2.5A VOUT = 2.5V 1MHz Burst Mode OPERATION 3.55 4.05 4.55 INPUT VOLTAGE (V) Load Regulation VIN = 3.3V VOUT = 2.5V -0.02 95 -0.04 1H 0.47H 94 2.2H 93 92 5.05 -0.06 -0.08 -0.10 -0.12 VIN = 3.3V VOUT = 2.5V LOAD = 1A Burst Mode OPERATION 91 300 -0.14 -0.16 800 1300 1800 2300 2800 3300 3800 FREQUENCY (kHz) -0.18 1 1.5 LOAD CURRENT (A) 2 2.5 VOUT 100mV/DIV VOUT 100mV/DIV Load Step Transient Burst Mode Operation IL 1A/DIV IL 1A/DIV VOUT 20mV/DIV IL 200mA/DIV 0.5 3412 G06 Load Step Transient Forced Continuous 3412 G07 0 3412 G05 Burst Mode Operation 4s/DIV 10 3412 G03 %VOUT/VOUT EFFICIENCY (%) EFFICIENCY (%) VOUT = 2.5V 1MHz FORCED CONTINUOUS 0.02 3412 G04 4 30 0 0.001 10 96 92 3.05 40 0.00 LOAD = 1A 86 2.55 50 Efficiency vs Frequency LOAD = 100mA 94 88 60 10 97 90 VIN = 5V 3412 G02 98 96 VIN = 3.3V 70 20 VOUT = 2.5V 1MHz Burst Mode OPERATION 0 0.001 10 0.01 0.1 1 LOAD CURRENT (A) 80 VIN = 5V 60 20 VIN = 3.3V VOUT = 2.5V VIN = 3.3V 70 EFFICIENCY (%) Burst Mode OPERATION EFFICIENCY (%) EFFICIENCY (%) 80 Efficiency vs Load Current 100 20s/DIV 3412 G08 20s/DIV 3412 G09 3412fc For more information www.linear.com/LTC3412 LTC3412 TYPICAL PERFORMANCE CHARACTERISTICS Reference Voltage vs Temperature Start-Up, Burst Mode Operation 0.7960 Switch On-Resistance vs Input Voltage 120 VIN = 3.3V 100 0.7950 ON-RESISTANCE (m) IL 1A/DIV VRUN 1V/DIV REFERENCE VOLTAGE (V) VOUT 1V/DIV 0.7955 0.7945 0.7940 0.7935 0.7930 3412 G10 80 60 NFET ON-RESISTANCE 40 20 0.7925 1ms/DIV PFET ON-RESISTANCE 0.7920 -45 -25 -5 0 15 35 55 75 95 115 120 TEMPERATURE (C) 2.5 3 3.5 4 INPUT VOLTAGE (V) 4.5 3412 G12 3412 G11 Switch On-Resistance vs Temperature VIN = 3.3V 110 100 2.0 PFET ON-RESISTANCE 90 80 70 60 NFET ON-RESISTANCE 50 1.0 SYNCHRONOUS SWITCH 30 0 20 40 60 80 TEMPERATURE (C) 0 100 120 2.5 3.5 4 4.5 INPUT VOLTAGE (V) 3 3412 G13 2500 2000 1500 1000 500 5 0 5.5 3412 G15 Switching Frequency vs Temperature DC Supply Current vs Input Voltage 350 1010 R = 309k 1008 1040 VIN = 3.3V 300 FREQUENCY (kHz) 1020 1010 DC SUPPLY CURRENT (A) 1006 1030 1004 1002 1000 998 996 994 1000 50 150 250 350 450 550 650 750 850 950 ROSC (k) 3412 G14 Frequency vs Input Voltage FREQUENCY (kHz) 3000 MAIN SWITCH 20 -40 -20 VIN = 3.3V 3500 1.5 0.5 40 1050 Frequency vs ROSC 4500 4000 LEAKAGE CURRENT (nA) ON-RESISTANCE (m) Switch Leakage vs Input Voltage 2.5 FREQUENCY (kHz) 120 ACTIVE 250 200 150 100 992 990 2.5 3 3.5 4 4.5 INPUT VOLTAGE (V) 5 5.5 3412 G16 5 990 -40 -20 SLEEP 0 20 40 60 80 TEMPERATURE (C) 100 120 3412 G17 50 2.5 3 3.5 4 4.5 INPUT VOLTAGE (V) 5 5.5 3412 G18 3412fc For more information www.linear.com/LTC3412 5 LTC3412 TYPICAL PERFORMANCE CHARACTERISTICS Minimum Peak Inductor Current vs Burst Clamp Voltage VIN = 3.3V SUPPLY CURRENT (A) 300 ACTIVE 250 200 150 100 SLEEP 50 0 -40 -20 0 20 40 60 80 TEMPERATURE (C) 4000 VIN = 3.3V 3500 6.6 3000 2500 2000 1500 1000 0 100 120 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 BURST CLAMP VOLTAGE (V) 1 3412 G20 6.2 6.0 5.8 5.4 2.75 3.25 4.75 4.25 3.75 INPUT VOLTAGE (V) 5.25 3412 G21 (FE/UH Package) SVIN (Pin 1/Pin 11): Signal Input Supply. Decouple this pin to SGND with a capacitor. Normally SVIN is equal to PVIN. SVIN can be greater than PVIN but keep the voltage difference between SVIN and PVIN less than 0.5V. PGOOD (Pin 2/Pin 12): Power Good Output. Open-drain logic output that is pulled to ground when the output voltage is not within 7.5% of regulation point. ITH (Pin 3/Pin 13): Error Amplifier Compensation Point. The current comparator threshold increases with this control voltage. Nominal voltage range for this pin is from 0.2V to 1.4V with 0.2V corresponding to the zero-sense voltage (zero current). VFB (Pin 4/Pin 14): Feedback Pin. Receives the feedback voltage from a resistive divider connected across the output. RT (Pin 5/Pin 15): Oscillator Resistor Input. Connecting a resistor to ground from this pin sets the switching frequency. SYNC/MODE (Pin 6/Pin 16): Mode Select and External Clock Synchronization Input. To select forced continuous, tie to SVIN. Connecting this pin to a voltage between 0V and 1V selects Burst Mode operation with the burst clamp set to the pin voltage. 6 6.4 5.6 500 3412 G19 PIN FUNCTIONS Current Limit vs Input Voltage 6.8 CURRENT LIMIT (A) 350 MINIMUM PEAK INDUCTOR CURRENT (mA) DC Supply Current vs Temperature RUN/SS (Pin 7/Pin 1): Run Control and Soft-Start Input. Forcing this pin below 0.5V shuts down the LTC3412. In shutdown all functions are disabled drawing < 1A of supply current. A capacitor to ground from this pin sets the ramp time to full output current. SGND (Pin 8/Pin 2): Signal Ground. All small-signal components, compensation components and the exposed pad on the bottom side of the IC should connect to this ground, which in turn connects to PGND at one point. PVIN (Pins 9, 16/Pins 3, 10): Power Input Supply. Decouple this pin to PGND with a capacitor. SW (Pins 10, 11, 14, 15/Pins 4, 5, 8, 9): Switch Node Connection to the Inductor. This pin connects to the drains of the internal main and synchronous power MOSFET switches. PGND (Pins 12, 13/Pins 6, 7): Power Ground. Connect this pin close to the (-) terminal of CIN and COUT. Exposed Pad (Pin 17/Pin 17): Signal Ground. Must be soldered to PCB for electrical connection and thermal performance. 3412fc For more information www.linear.com/LTC3412 LTC3412 FUNCTIONAL BLOCK DIAGRAM SVIN SGND ITH 1 8 3 PVIN 9 SLOPE COMPENSATION RECOVERY VOLTAGE REFERENCE 0.8V PMOS CURRENT COMPARATOR + BCLAMP + - - VFB 4 0.74V + - RUN/SS 7 RUN 0.86V ERROR AMPLIFIER SYNC/MODE + - + 16 - P-CH BURST COMPARATOR 10 SLOPE COMPENSATION OSCILLATOR 11 14 SW 15 + N-CH LOGIC - + PGOOD 2 NMOS CURRENT COMPARATOR REVERSE CURRENT COMPARATOR 5 6 RT SYNC/MODE - - + 12 13 PGND 3412 FBD OPERATION Main Control Loop The LTC3412 is a monolithic, constant-frequency, current mode step-down DC/DC converter. During normal operation, the internal top power switch (P-channel MOSFET) is turned on at the beginning of each clock cycle. Current in the inductor increases until the current comparator trips and turns off the top power MOSFET. The peak inductor current at which the current comparator shuts off the top power switch is controlled by the voltage on the ITH pin. The error amplifier adjusts the voltage on the ITH pin by comparing the feedback signal from a resistor divider on the VFB pin with an internal 0.8V reference. When the load current increases, it causes a reduction in the feedback voltage relative to the reference. The error amplifier raises the ITH voltage until the average inductor current matches the new load current. When the top power MOSFET shuts off, the synchronous power switch (Nchannel MOSFET) turns on until either the bottom current limit is reached or the beginning of the next clock cycle. The bottom current limit is set at -2A for forced continuous mode and 0A for Burst Mode operation. The operating frequency is set by an external resistor connected between the RT pin and ground. The practical switching frequency can range from 300kHz to 4MHz. For more information www.linear.com/LTC3412 3412fc 7 LTC3412 OPERATION Overvoltage and undervoltage comparators will pull the PGOOD output low if the output voltage comes out of regulation by 7.5%. In an overvoltage condition, the top power MOSFET is turned off and the bottom power MOSFET is switched on until either the overvoltage condition clears or the bottom MOSFET's current limit is reached. peak inductor current will be determined by the voltage on the ITH pin until the ITH voltage drops below 200mV. At this point, the peak inductor current is determined by the minimum on-time of the current comparator. If the load demand is less than the average of the minimum on-time inductor current, switching cycles will be skipped to keep the output voltage in regulation. Forced Continuous Mode Frequency Synchronization Connecting the SYNC/MODE pin to SVIN will disable Burst Mode operation and force continuous current operation. At light loads, forced continuous mode operation is less efficient than Burst Mode operation but may be desirable in some applications where it is necessary to keep switching harmonics out of a signal band. The output voltage ripple is minimized in this mode. The internal oscillator of the LTC3412 can be synchronized to an external clock connected to the SYNC/MODE pin. The frequency of the external clock can be in the range of 300kHz to 4MHz. For this application, the oscillator timing resistor should be chosen to correspond to a frequency that is 25% lower than the synchronization frequency. During synchronization, the burst clamp is set to 0V and each switching cycle begins at the falling edge of the external clock signal. Burst Mode Operation Connecting the SYNC/MODE pin to a voltage between 0V to 1V enables Burst Mode operation. In Burst Mode operation, the internal power MOSFETs operate intermittently at light loads. This increases efficiency by minimizing switching losses. During Burst Mode operation, the minimum peak inductor current is externally set by the voltage on the SYNC/MODE pin and the voltage on the ITH pin is monitored by the burst comparator to determine when sleep mode is enabled and disabled. When the average inductor current is greater than the load current, the voltage on the ITH pin drops. As the ITH voltage falls below 150mV, the burst comparator trips and enables sleep mode. During sleep mode, the top MOSFET is held off and the ITH pin is disconnected from the output of the error amplifier. The majority of the internal circuitry is also turned off to reduce the quiescent current to 62A while the load current is solely supplied by the output capacitor. When the output voltage drops, the ITH pin is reconnected to the output of the error amplifier and the top power MOSFET along with all the internal circuitry is switched back on. This process repeats at a rate that is dependent on the load demand. Pulse skipping operation can be implemented by connecting the SYNC/MODE pin to ground. This forces the burst clamp level to be at 0V. As the load current decreases, the 8 Dropout Operation When the input supply voltage decreases toward the output voltage, the duty cycle increases toward the maximum on-time. Further reduction of the supply voltage forces the main switch to remain on for more than one cycle eventually reaching 100% duty cycle. The output voltage will then be determined by the input voltage minus the voltage drop across the internal P-channel MOSFET and the inductor. Low Supply Operation The LTC3412 is designed to operate down to an input supply voltage of 2.625V. One important consideration at low input supply voltages is that the RDS(ON) of the P-channel and N-channel power switches increases. The user should calculate the power dissipation when the LTC3412 is used at 100% duty cycle with low input voltages to ensure that thermal limits are not exceeded. Slope Compensation and Inductor Peak Current Slope compensation provides stability in constant frequency architectures by preventing subharmonic oscillations at duty cycles greater than 50%. It is accomplished internally by adding a compensating ramp to the inductor 3412fc For more information www.linear.com/LTC3412 LTC3412 OPERATION current signal at duty cycles in excess of 40%. Normally, the maximum inductor peak current is reduced when slope compensation is added. In the LTC3412, however, slope compensation recovery is implemented to keep the maximum inductor peak current constant throughout the range of duty cycles. This keeps the maximum output current relatively constant regardless of duty cycle. Short-Circuit Protection When the output is shorted to ground, the inductor current decays very slowly during a single switching cycle. To prevent current runaway from occurring, a secondary current limit is imposed on the inductor current. If the inductor valley current increases larger than 4.8A, the top power MOSFET will be held off and switching cycles will be skipped until the inductor current falls to a safe level. APPLICATIONS INFORMATION The basic LTC3412 application circuit is shown in Figure 1. External component selection is determined by the maximum load current and begins with the selection of the inductor value and operating frequency followed by CIN and COUT. Operating Frequency Selection of the operating frequency is a tradeoff between efficiency and component size. High frequency operation allows the use of smaller inductor and capacitor values. Operation at lower frequencies improves efficiency by reducing internal gate charge and switching losses but requires larger inductance values and/or capacitance to maintain low output ripple voltage. The operating frequency of the LTC3412 is determined by an external resistor that is connected between the RT pin and ground. The value of the resistor sets the ramp current that is used to charge and discharge an internal timing capacitor within the oscillator and can be calculated by using the following equation: ROSC = 3.23 *1011 ()-10k f(Hz) Although frequencies as high as 4MHz are possible, the minimum on-time of the LTC3412 imposes a minimum limit on the operating duty cycle. The minimum on-time is typically 110ns. Therefore, the minimum duty cycle is equal to 100 * 110ns * f(Hz). Inductor Selection For a given input and output voltage, the inductor value and operating frequency determine the ripple current. The ripple current IL increases with higher VIN and decreases with higher inductance. V V IL = OUT 1- OUT fL VIN Having a lower ripple current reduces the ESR losses in the output capacitors and the output voltage ripple. Highest efficiency operation is achieved at low frequency with small ripple current. This, however, requires a large inductor. A reasonable starting point for selecting the ripple current is IL = 0.4(IMAX). The largest ripple current occurs at the highest VIN. To guarantee that the ripple current stays below a specified maximum, the inductor value should be chosen according to the following equation: V V L = OUT 1- OUT fIL(MAX) VIN(MAX) The inductor value will also have an effect on Burst Mode operation. The transition from low current operation begins when the peak inductor current falls below a level set by the burst clamp. Lower inductor values result in higher ripple current which causes this to occur at lower load currents. This causes a dip in efficiency in the upper range of low current operation. In Burst Mode operation, lower inductance values will cause the burst frequency to increase. 3412fc For more information www.linear.com/LTC3412 9 LTC3412 APPLICATIONS INFORMATION Inductor Core Selection Once the value for L is known, the type of inductor must be selected. High efficiency converters generally cannot afford the core loss found in low cost powdered iron cores, forcing the use of more expensive ferrite, mollypermalloy, or Kool M(R) cores. Actual core loss is independent of core size for a fixed inductor value but it is very dependent on the inductance selected. As the inductance increases, core losses decrease. Unfortunately, increased inductance requires more turns of wire and therefore copper losses will increase. Ferrite designs have very low core losses and are preferred at high switching frequencies, so design goals can concentrate on copper loss and preventing saturation. Ferrite core material saturates "hard," which means that inductance collapses abruptly when the peak design current is exceeded. This results in an abrupt increase in inductor ripple current and consequent output voltage ripple. Do not allow the core to saturate! Different core materials and shapes will change the size/current and price/current relationship of an inductor. Toroid or shielded pot cores in ferrite or permalloy materials are small and don't radiate energy but generally cost more than powdered iron core inductors with similar characteristics. The choice of which style inductor to use mainly depends on the price vs size requirements and any radiated field/EMI requirements. New designs for surface mount inductors are available from Coiltronics, Coilcraft, Toko and Sumida. CIN and COUT Selection The input capacitance, CIN, is needed to filter the trapezoidal current at the source of the top MOSFET. To prevent large ripple voltage, a low ESR input capacitor sized for the maximum RMS current should be used. RMS current is given by: V IRMS =IOUT(MAX) OUT VIN VIN -1 VOUT This formula has a maximum at VIN = 2VOUT, where IRMS = IOUT/2. This simple worst-case condition is commonly used for design because even significant deviations do 10 not offer much relief. Note that ripple current ratings from capacitor manufacturers are often based on only 2000 hours of life which makes it advisable to further derate the capacitor, or choose a capacitor rated at a higher temperature than required. Several capacitors may also be paralleled to meet size or height requirements in the design. The selection of COUT is determined by the effective series resistance (ESR) that is required to minimize voltage ripple and load step transients, as well as the amount of bulk capacitance that is necessary to ensure that the control loop is stable. Loop stability can be checked by viewing the load transient response as described in a later section. The output ripple, VOUT, is determined by: 1 VOUT IL ESR+ 8fCOUT The output ripple is highest at maximum input voltage since IL increases with input voltage. Multiple capacitors placed in parallel may be needed to meet the ESR and RMS current handling requirements. Dry tantalum, special polymer, aluminum electrolytic and ceramic capacitors are all available in surface mount packages. Special polymer capacitors offer very low ESR but have lower capacitance density than other types. Tantalum capacitors have the highest capacitance density but it is important to only use types that have been surge tested for use in switching power supplies. Aluminum electrolytic capacitors have significantly higher ESR but can be used in costsensitive applications provided that consideration is given to ripple current ratings and long term reliability. Ceramic capacitors have excellent low ESR characteristics but can have a high voltage coefficient and audible piezoelectric effects. The high Q of ceramic capacitors with trace inductance can also lead to significant ringing. Using Ceramic Input and Output Capacitors Higher values, lower cost ceramic capacitors are now becoming available in smaller case sizes. Their high ripple current, high voltage rating and low ESR make them ideal for switching regulator applications. However, care must be taken when these capacitors are used at the input and output. When a ceramic capacitor is used at the input and 3412fc For more information www.linear.com/LTC3412 LTC3412 APPLICATIONS INFORMATION the power is supplied by a wall adapter through long wires, a load step at the output can induce ringing at the input, VIN. At best, this ringing can couple to the output and be mistaken as loop instability. At worst, a sudden inrush of current through the long wires can potentially cause a voltage spike at VIN large enough to damage the part. Output Voltage Programming The output voltage is set by an external resistive divider according to the following equation: R2 VOUT = 0.8V 1+ R1 The resistive divider allows the VFB pin to sense a fraction of the output voltage as shown in Figure 2. VOUT R2 VFB R1 LTC3412 SGND 3412 F02 Figure 2. Setting the Output Voltage inductor current to remain equal to IBURST regardless of further reductions in the load current. Since the average inductor current is greater than the output load current, the voltage on the ITH pin will decrease. When the ITH voltage drops to 150mV, sleep mode is enabled in which both power MOSFETs are shut off along with most of the circuitry to minimize power consumption. All circuitry is turned back on and the power MOSFETs begin switching again when the output voltage drops out of regulation. The value for IBURST is determined by the desired amount of output voltage ripple. As the value of IBURST increases, the sleep period between pulses and the output voltage ripple increase. The burst clamp voltage, VBURST, can be set by a resistor divider from the VFB pin to the SGND pin as shown in Figure 1. Pulse skipping, which is a compromise between low output voltage ripple and efficiency, can be implemented by connecting the SYNC/MODE pin to ground. This sets IBURST to 0A. In this condition, the peak inductor current is limited by the minimum on-time of the current comparator, and the lowest output voltage ripple is achieved while still operating discontinuously. During very light output loads, pulse skipping allows only a few switching cycles to be skipped while maintaining the output voltage in regulation. Burst Clamp Programming Frequency Synchronization If the voltage on the SYNC/MODE pin is less than VIN by 1V, Burst Mode operation is enabled. During Burst Mode operation, the voltage on the SYNC/MODE pin determines the burst clamp level which sets the minimum peak inductor current, IBURST, for each switching cycle according to the following equation: The LTC3412's internal oscillator can be synchronized to an external clock signal. During synchronization, the top MOSFET turn-on is locked to the falling edge of the external frequency source. The synchronization frequency range is 300kHz to 4MHz. Synchronization only occurs if the external frequency is greater than the frequency set by the external resistor. Because slope compensation is generated by the oscillator's RC circuit, the external frequency should be set 25% higher than the frequency set by the external resistor to ensure that adequate slope compensation is present. 3.75A IBURST = ( VBURST -0.2V ) 0.8V VBURST is the voltage on the SYNC/MODE pin. IBURST can be programmed in the range of 0A to 3.75A. For values of VBURST greater than 1V, IBURST is set at 3.75A. For values of VBURST less than 0.2V, IBURST is set at 0A. As the output load current drops, the peak inductor current decreases to keep the output voltage in regulation. When the output load current demands a peak inductor current that is less than IBURST, the burst clamp will force the peak Soft-Start The RUN/SS pin provides a means to shut down the LTC3412 as well as a timer for soft-start. Pulling the RUN/ SS pin below 0.5V places the LTC3412 in a low quiescent current shutdown state (IQ < 1A). 3412fc For more information www.linear.com/LTC3412 11 LTC3412 APPLICATIONS INFORMATION The LTC3412 contains an internal soft-start clamp that gradually raises the clamp on ITH after the RUN/SS pin is pulled above 2V. The full current range becomes available on ITH after 1024 switching cycles. If a longer soft-start period is desired, the clamp on ITH can be set externally with a resistor and capacitor on the RUN/SS pin as shown in Figure 1. The soft-start duration can be calculated by using the following formula: VIN t SS =RSSCSS ln (Seconds) VIN -1.8V 2. I2R losses are calculated from the resistances of the internal switches, RSW and external inductor RL. In continuous mode the average output current flowing through inductor L is "chopped" between the main switch and the synchronous switch. Thus, the series resistance looking into the SW pin is a function of both top and bottom MOSFET RDS(ON) and the duty cycle (DC) as follows: RSW = (RDS(ON)TOP)(DC) + (RDS(ON)BOT)(1 - DC) Efficiency Considerations The efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine what is limiting the efficiency and which change would produce the most improvement. Efficiency can be expressed as: Efficiency = 100% - (L1 + L2 + L3 + ...) where L1, L2, etc. are the individual losses as a percentage of input power. Although all dissipative elements in the circuit produce losses, two main sources usually account for most of the losses: VIN quiescent current and I2R losses. The VIN quiescent current loss dominates the efficiency loss at very low load currents whereas the I2R loss dominates the efficiency loss at medium to high load currents. In a typical efficiency plot, the efficiency curve at very low load currents can be misleading since the actual power lost is of no consequence. 1. The VIN quiescent current is due to two components: the DC bias current as given in the electrical characteristics and the internal main switch and synchronous switch gate charge currents. The gate charge current results from switching the gate capacitance of the internal power MOSFET switches. Each time the gate is switched from high to low to high again, a packet of charge dQ moves from VIN to ground. The resulting dQ/dt is the current out of VIN that is typically larger than the DC bias current. In continuous mode, IGATECHG=f(QT + QB) where QT and 12 QB are the gate charges of the internal top and bottom switches. Both the DC bias and gate charge losses are proportional to VIN and thus their effects will be more pronounced at higher supply voltages. The RDS(ON) for both the top and bottom MOSFETs can be obtained from the Typical Performance Characteristics curves. Thus, to obtain I2R losses, simply add RSW to RL and multiply the result by the square of the average output current. Other losses including CIN and COUT ESR dissipative losses and inductor core losses generally account for less than 2% of the total loss. Thermal Considerations In most applications, the LTC3412 does not dissipate much heat due to its high efficiency. But, in applications where the LTC3412 is running at high ambient temperature with low supply voltage and high duty cycles, such as in dropout, the heat dissipated may exceed the maximum junction temperature of the part. If the junction temperature reaches approximately 150C, both power switches will be turned off and the SW node will become high impedance. To avoid the LTC3412 from exceeding the maximum junction temperature, the user will need to do some thermal analysis. The goal of the thermal analysis is to determine whether the power dissipated exceeds the maximum junction temperature of the part. The temperature rise is given by: TR = (PD)(JA) where PD is the power dissipated by the regulator and JA is the thermal resistance from the junction of the die to the ambient temperature. 3412fc For more information www.linear.com/LTC3412 LTC3412 APPLICATIONS INFORMATION The junction temperature, TJ, is given by: First, calculate the timing resistor: TJ = TA + TR ROSC = where TA is the ambient temperature. As an example, consider the LTC3412 in dropout at an input voltage of 3.3V, a load current of 2.5A and an ambient temperature of 70C. From the typical performance graph of switch resistance, the RDS(ON) of the P-channel switch at 70C is approximately 97m. Therefore, power dissipated by the part is: PD = (ILOAD2)(RDS(ON)) = (2.5A)2(97m) = 0.61W For the TSSOP package, the JA is 37.6C/W. Thus the junction temperature of the regulator is: TJ = 70C + (0.61W)(37.6C/W) = 93C which is below the maximum junction temperature of 125C. Note that at higher supply voltages, the junction temperature is lower due to reduced switch resistance (RDS(ON)). Checking Transient Response The regulator loop response can be checked by looking at the load transient response. Switching regulators take several cycles to respond to a step in load current. When a load step occurs, VOUT immediately shifts by an amount equal to ILOAD(ESR), where ESR is the effective series resistance of COUT. ILOAD also begins to charge or discharge COUT generating a feedback error signal used by the regulator to return VOUT to its steady-state value. During this recovery time, VOUT can be monitored for overshoot or ringing that would indicate a stability problem. The ITH pin external components and output capacitor shown in Figure 1 will provide adequate compensation for most applications. Design Example As a design example, consider using the LTC3412 in an application with the following specifications: VIN = 2.7V to 4.2V, VOUT = 2.5V, IOUT(MAX) = 2.5A, IOUT(MIN) = 10mA, f = 1MHz. Because efficiency is important at both high and low load current, Burst Mode operation will be utilized. 3.23 *1011 1*106 -10k = 313k Use a standard value of 309k. Next, calculate the inductor value for about 40% ripple current at maximum VIN: 2.5V 2.5V L = =1.01H 1- (1MHz)(1A) 4.2V Using a 1H inductor, results in a maximum ripple current of: 2.5V 2.5V IL = =1.01A 1- (1MHz)(1H) 4.2V COUT will be selected based on the ESR that is required to satisfy the output voltage ripple requirement and the bulk capacitance needed for loop stability. In this application, two tantalum capacitors will be used to provide the bulk capacitance and a ceramic capacitor in parallel to lower the total effective ESR. For this design, two 100F tantalum capacitors in parallel with a 10F ceramic capacitor will be used. CIN should be sized for a maximum current rating of: 2.5V 4.2V IRMS= (2.5A ) -1=1.23ARMS 4.2V 2.5V Decoupling the PVIN and SVIN pins with a 22F ceramic capacitor and a 220F tantalum capacitor is adequate for most applications. The burst clamp and output voltage can now be programmed by choosing the values of R1, R2 and R3. The voltage on the MODE pin will be set to 0.32V by the resistor divider consisting of R2 and R3. A burst clamp voltage of 0.32V will set the minimum inductor current, IBURST, as follows: 3.75V IBURST= (0.32V -0.2V ) = 563mA 0.8V 3412fc For more information www.linear.com/LTC3412 13 LTC3412 APPLICATIONS INFORMATION If we set the sum of R2 and R3 to 185k, then the following equations can be solved: R2+R3 =185k 1+ R2 0.8V = R3 0.32V The last two equations shown result in the following values for R2 and R3: R2 = 110k , R3 = 75k. The value of R1 can now be determined by solving the equation shown below: R1 2.5V = 185k 0.8V R1= 393k 1+ A value of 392k will be selected for R1. Figure 4 shows the complete schematic for this design example. PC Board Layout Checklist When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the LTC3412. Check the following in your layout. 1. A ground plane is recommended. If a ground plane layer is not used, the signal and power grounds should be segregated with all small-signal components returning to the SGND pin at one point which is then connected to the PGND pin close to the LTC3412. The exposed pad should be connected to SGND. 2. Connect the (+) terminal of the input capacitor(s), CIN, as close as possible to the PVIN pin. This capacitor provides the AC current into the internal power MOSFETs. 3. Keep the switching node, SW, away from all sensitive small-signal nodes. 4. Flood all unused areas on all layers with copper. Flooding with copper will reduce the temperature rise of power components. You can connect the copper areas to any DC net (PVIN, SVIN, VOUT, PGND, SGND, or any other DC rail in your system). 5. Connect the VFB pin directly to the feedback resistors. The resistor divider must be connected between VOUT and SGND. Top Side Bottom Side Figure 3. LTC3412 Layout Diagram 14 3412fc For more information www.linear.com/LTC3412 LTC3412 APPLICATIONS INFORMATION VIN 2.7V TO 4.2V CFB 22pF X5R R1 392k 1 PGOOD RPG 100k CITH 680pF X7R RITH 7.15k 2 3 CC 100pF RSS 4.7M PGOOD SW ITH SW LTC3412 4 R3 75k PVIN SVIN VFB R2 110k 5 ROSC 309k 6 SYNC/MODE 7 CSS 470pF X7R 8 RT PGND PGND SW RUN SW SGND PVIN 16 CIN1 220F 15 14 L1* 1H 13 COUT2 10F 11 + 10 COUT1** 100F x2 9 CIN2 22F X5R 6.3V *TOKO D62CB A920CY-1ROM **SANYO POSCAP 4TPB100M TAIYO YUDEN LMK325BJ106MN SANYO POSCAP 2R5TPC220M VOUT 2.5V 2.5A 12 GND 3412 F04 Figure 4. Single Lithium-Ion to 2.5V, 2.5A Regulator at 1MHz, Burst Mode Operation Using POSCAPs 3412fc For more information www.linear.com/LTC3412 15 LTC3412 TYPICAL APPLICATIONS 2.5V, 2.5A Regulator Using All Ceramic Capacitors CIN3** 100F C1 22pF X5R VIN 2.7V TO 5.5V R1 392k 1 PGOOD RPG 100k 2 CITH 1000pF X7R RITH 15k 3 CC 100pF RSS 4.7M PVIN PGOOD SW SW ITH LTC3412 4 R2 110k 5 ROSC 309k 6 R3 75k SVIN 7 CSS 470pF X7R 8 PGND VFB PGND RT SW SYNC/MODE RUN SW SGND PVIN CIN1 22F X5R 6.3V 16 15 14 L1* 1H 13 VOUT 2.5V 2.5A 12 11 COUT** 100F 10 9 CIN2 22F X5R 6.3V GND 3412 F05 *TOKO D62CB A920CY-1ROM **TDK C4532X5R0J107M 1.8V, 2.5A Step-Down Regulator at 1MHz, Burst Mode Operation VIN 3.3V C1 22pF X5R R1 232k 1 PGOOD RPG 100k CITH 560pF X7R RITH 10k 2 3 C2 47pF RSS 4.7M PGOOD SW ITH SW LTC3412 4 R3 75k PVIN SVIN R2 110k 5 ROSC 309k 6 7 CSS 470pF X7R 8 VFB RT SYNC/MODE PGND PGND SW RUN SW SGND PVIN CIN1** 22F 16 15 14 L1 1H* 13 VOUT 1.8V 2A 12 11 COUT** 22F x2 10 9 CIN2 22F** 3412 TA05 GND *SUMIDA CR431R0 **AVX 12066D226MAT 16 3412fc For more information www.linear.com/LTC3412 LTC3412 TYPICAL APPLICATIONS 2.5V, 2.5A Low Output Noise Regulator at 2MHz CIN3 0.1F X5R RIN 5 R1 392k 1 RPG 100k CITH 1000pF X7R RITH 22.1k 2 3 C1 56pF R2 182k 5 ROSC 137k 6 7 CSS 470pF X7R 8 RSS 4.7M PVIN SVIN PGOOD SW ITH SW LTC3412 4 VFB RT PGND PGND SW SYNC/MODE RUN SW SGND PVIN CIN1** 100F 16 15 14 L1 0.47H* 13 VOUT 2.5V 2.5A 12 11 COUT** 100F x2 10 9 CIN2 100F** 3412 TA06 GND *VISHAY DALE IHLP-2525CZ-01 0.47 **TDK C4532X5R0J107M Efficiency vs Load Current 2MHz, Low Noise 100 90 80 EFFICIENCY (%) PGOOD VIN 3.3V CFF 22pF X7R 70 60 50 40 30 20 10 0 0.01 0.1 1 LOAD CURRENT (A) 10 3412 TA07 3412fc For more information www.linear.com/LTC3412 17 LTC3412 TYPICAL APPLICATIONS 3.3V, 2.5A Step-Down Regulator at 1MHz, Forced Continuous Mode Operation CIN3** 100F C1 22pF X5R VIN 5V R1 634k 1 PGOOD RPG 100k CITH 1000pF X7R RITH 15k 2 3 CC 100pF SW PGOOD SW ITH LTC3412 4 PGND VFB R2 200k 5 ROSC 309k 6 7 RSS 4.7M PVIN SVIN CSS 470pF X7R 8 PGND RT SW SYNC/MODE RUN SW SGND PVIN CIN1 22F X5R 6.3V 16 15 14 L1* 1H 13 VOUT 3.3V 2.5A 12 11 COUT** 100F 10 9 CIN2 22F X5R 6.3V GND 3412 TA01 *PULSE P1166.162T **TDK C4532X5R0J107M Lithium-Ion to 3.3V, Single Inductor Buck-Boost Converter GND R1 576k 1 PGOOD RPG 100k CITH 1000pF X7R RITH 15k 2 3 C2 100pF R3 75k RSS 4.7M SVIN PVIN PGOOD SW ITH SW LTC3412 4 R2 110k 5 ROSC 309k 6 7 CSS 470pF X7R 8 VFB RT SYNC/MODE PGND PGND SW RUN SW SGND PVIN 16 CIN1 22F X5R 6.3V 15 14 L1* 2H 13 12 D1 DIODES, INC. B320A M1 SILICONIX Si2302DS 11 18 VOUT 3.3V COUT** 100F 10 9 CIN2 22F X5R 6.3V *TOKO D63CB **TDK C4532X5R0J107M VIN 2.7V TO 4.2V CIN3** 100F x2 C1 22pF 3412 F04 GND VIN 2.7V 3V 3.5V 4.2V MAXIMUM IOUT 800mA 900mA 1.05A 1.2A 3412fc For more information www.linear.com/LTC3412 LTC3412 PACKAGE DESCRIPTION Please refer to http://www.linear.com/product/LTC3412#packaging for the most recent package drawings. FE Package 16-Lead Plastic TSSOP (4.4mm) (Reference LTC DWG # 05-08-1663 Rev L) Exposed Pad Variation BA 4.90 - 5.10* (.193 - .201) 2.74 (.108) 2.74 (.108) 16 1514 13 12 1110 6.60 0.10 4.50 0.10 9 2.74 (.108) 2.74 6.40 (.108) (.252) BSC SEE NOTE 4 0.45 0.05 1.05 0.10 0.65 BSC 1 2 3 4 5 6 7 8 RECOMMENDED SOLDER PAD LAYOUT 4.30 - 4.50* (.169 - .177) 0.09 - 0.20 (.0035 - .0079) 0.25 REF 0 - 8 0.65 (.0256) BSC 0.50 - 0.75 (.020 - .030) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS MILLIMETERS 2. DIMENSIONS ARE IN (INCHES) 3. DRAWING NOT TO SCALE 1.10 (.0433) MAX 0.195 - 0.30 (.0077 - .0118) TYP 0.05 - 0.15 (.002 - .006) FE16 (BA) TSSOP REV L 0117 4. RECOMMENDED MINIMUM PCB METAL SIZE FOR EXPOSED PAD ATTACHMENT *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.150mm (.006") PER SIDE 3412fc For more information www.linear.com/LTC3412 19 LTC3412 PACKAGE DESCRIPTION Please refer to http://www.linear.com/product/LTC3412#packaging for the most recent package drawings. UF Package 16-Lead Plastic QFN (4mm x 4mm) (Reference LTC DWG # 05-08-1692 Rev O) 0.72 0.05 4.35 0.05 2.15 0.05 2.90 0.05 (4 SIDES) PACKAGE OUTLINE 0.30 0.05 0.65 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS BOTTOM VIEW--EXPOSED PAD 4.00 0.10 (4 SIDES) 0.75 0.05 R = 0.115 TYP 15 PIN 1 NOTCH R = 0.20 TYP OR 0.35 x 45 CHAMFER 16 0.55 0.20 PIN 1 TOP MARK (NOTE 6) 1 2.15 0.10 (4-SIDES) 2 (UF16) QFN 10-04 0.200 REF 0.00 - 0.05 0.30 0.05 0.65 BSC NOTE: 1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE MO-220 VARIATION (WGGC) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 20 3412fc For more information www.linear.com/LTC3412 LTC3412 REVISION HISTORY (Revision history begins at Rev C) REV DATE DESCRIPTION C 05/17 Add Storage Temperature to Absolute Maximum Ratings PAGE NUMBER 2 3412fc Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its information circuits as described herein will not infringe on existing patent rights. For more www.linear.com/LTC3412 21 LTC3412 TYPICAL APPLICATION 2.5V, 2.5A Step-Down Regulator Synchronized to 1.25MHz CIN3** 100F C1 22pF X5R VIN 2.7V TO 5.5V R1 392k 1 PGOOD RPG 100k 2 CITH 1000pF X7R RITH 15k 3 PGOOD SW ITH SW LTC3412 CC 100pF 4 R2 182k PVIN SVIN 5 VFB RT PGND PGND ROSC 309k 1.25MHz 6 SYNC/MODE EXT CLOCK 7 RUN CSS 470pF X7R 8 SGND SW RSS 4.7M SW PVIN 16 CIN1 22F X5R 6.3V 15 14 L1* 1H 13 12 11 COUT1** 100F 10 9 CIN2 22F X5R 6.3V *TOKO D62CB A920CY-1ROM **TDK C4532X5R0J107M VOUT 2.5V 2.5A GND 3412 TA02 RELATED PARTS PART NUMBER DESCRIPTION LTC1701/LTC1701B 700mA (IOUT), 1MHz Step-Down Converter COMMENTS VIN = 2.5V to 5V, B Version: Burst Mode Defeat, ThinSOTTM LTC1772/LTC1772B Constant 550kHz Current Mode Step-Down DC/DC Controller VIN = 2.5V to 9.8V, 94% Efficiency, 100% Duty Cycle, ThinSOT VIN = 2.65V to 8.5V, 95% Efficiency, VOUT from 0.8V to VIN, MSOP-10 LTC1773 Constant Frequency 550kHz Step-Down DC/DC Controller LTC1875 1.5A (IOUT), 500kHz Synchronous Step-Down Converter VIN = 2.65V to 6V, 95% Efficiency, PLL, SSOP-16 LTC1877 600mA (IOUT), 500kHz Synchronous Step-Down Converter VIN = 2.65V to 10V, 95% Efficiency, MSOP-8 LTC1878 600mA (IOUT), 550kHz Synchronous Step-Down Converter VIN = 2.65V to 6V, 95% Efficiency, MSOP-8 LTC1879 1.2A (IOUT), 550kHz Synchronous Step-Down Converter VIN = 2.65V to 10V, 95% Efficiency, SSOP-16 LTC3404 600mA (IOUT), 1.4MHz Synchronous Step-Down Converter VIN = 2.65V to 6V, 95% Efficiency, MSOP-8 LTC3405A 300mA (IOUT), 1.5MHz Synchronous Step-Down Converter VIN = 2.65V to 6V, 96% Efficiency, ThinSOT Package LTC3406/LTC3406B 600mA (IOUT), 1.5MHz Synchronous Step-Down Converter LTC3411 22 1.25A (IOUT), 4MHz Synchronous Step-Down Converter VIN = 2.5V to 5.5V, 95% Efficiency, ThinSOT, B Version: Burst Mode Defeat VIN = 2.5V to 5.5V, 95% Efficiency, MSOP-10 3412fc LT 0517 REV C * PRINTED IN USA www.linear.com/LTC3412 LINEAR TECHNOLOGY CORPORATION 2002