UC3842A, UC3843A, UC2842A, UC2843A High Performance Current Mode Controllers The UC3842A, UC3843A series of high performance fixed frequency current mode controllers are specifically designed for off-line and DC-to-DC converter applications offering the designer a cost effective solution with minimal external components. These integrated circuits feature a trimmed oscillator for precise duty cycle control, a temperature compensated reference, high gain error amplifier, current sensing comparator, and a high current totem pole output ideally suited for driving a power MOSFET. Also included are protective features consisting of input and reference undervoltage lockouts each with hysteresis, cycle-by-cycle current limiting, programmable output deadtime, and a latch for single pulse metering. These devices are available in an 8-pin dual-in-line plastic package as well as the 14-pin plastic surface mount (SOIC-14). The SOIC-14 package has separate power and ground pins for the totem pole output stage. The UCX842A has UYLO thresholds of 16 V (on) and 10 V (off), ideally suited for off-line converters. The UCX843A is tailored for lower voltage applications having UVLO thresholds of 8.5 V (on) and 7.6 V (off). PDIP-8 N SUFFIX CASE 626 8 1 SOIC-14 D SUFFIX CASE 751A 14 1 SOIC-8 D1 SUFFIX CASE 751 8 1 PIN CONNECTIONS Features * Trimmed Oscillator Discharge Current for Precise Duty Cycle * * * * * * * * * http://onsemi.com Control Current Mode Operation to 500 kHz Automatic Feed Forward Compensation Latching PWM for Cycle-By-Cycle Current Limiting Internally Trimmed Reference with Undervoltage Lockout High Current Totem Pole Output Undervoltage Lockout with Hysteresis Low Startup and Operating Current Direct Interface with ON Semiconductor SENSEFETTM Products Pb-Free Packages are Available Compensation 1 8 Vref Voltage Feedback 2 7 VCC Current Sense 3 6 Output RT/CT 4 5 GND (Top View) Compensation 1 14 Vref NC 2 13 NC Voltage Feedback 3 12 VCC NC 4 11 VC Current Sense 5 10 Output NC 6 9 GND RT/CT 7 8 Power Ground (Top View) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 15 of this data sheet. DEVICE MARKING INFORMATION See general marking information in the device marking section on page 16 of this data sheet. (c) Semiconductor Components Industries, LLC, 2005 November, 2005 - Rev. 8 1 Publication Order Number: UC3842A/D UC3842A, UC3843A, UC2842A, UC2843A VCC Vref 5.0V Reference 8(14) R RTCT VCC Undervoltage Lockout Vref Undervoltage Lockout R 7(12) VC 7(11) Output Oscillator 4(7) Latching PWM Voltage Feedback Input + - 2(3) Output Compensation 1(1) Error Amplifier 6(10) Power Ground 5(8) Current Sense 3(5) Input GND 5(9) Pin numbers in parenthesis are for the D suffix SOIC-14 package. Figure 1. Simplified Block Diagram MAXIMUM RATINGS Rating Symbol Value Unit Bias and Driver Voltages (Zero Series Impedance, see also Total Device spec) VCC, VC 30 V Total Power Supply and Zener Current (ICC + IZ) 30 mA Output Current, Source or Sink (Note 1) IO 1.0 A Output Energy (Capacitive Load per Cycle) W 5.0 J Current Sense and Voltage Feedback Inputs Vin - 0.3 to + 5.5 V Error Amp Output Sink Current IO 10 mA PD RJA 862 145 mW C/W PD RJA 1.25 100 W C/W Operating Junction Temperature TJ + 150 C Operating Ambient Temperature UC3842A, UC3843A UC2842A, UC2843A TA Storage Temperature Range Tstg Power Dissipation and Thermal Characteristics D Suffix, Plastic Package Maximum Power Dissipation @ TA = 25C Thermal Resistance, Junction-to-Air N Suffix, Plastic Package Maximum Power Dissipation @ TA = 25C Thermal Resistance, Junction-to-Air C 0 to + 70 - 25 to + 85 - 65 to + 150 C Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. 1. Maximum Package power dissipation limits must be observed. http://onsemi.com 2 UC3842A, UC3843A, UC2842A, UC2843A ELECTRICAL CHARACTERISTICS (VCC = 15 V, [Note 2], RT = 10 k, CT = 3.3 nF, TA = Tlow to Thigh [Note 3], unless otherwise noted.) UC284XA UC384XA Symbol Min Typ Max Min Typ Max Unit Vref 4.95 5.0 5.05 4.9 5.0 5.1 V Line Regulation (VCC = 12 V to 25 V) Regline - 2.0 20 - 2.0 20 mV Load Regulation (IO = 1.0 mA to 20 mA) Regload - 3.0 25 - 3.0 25 mV Temperature Stability TS - 0.2 - - 0.2 - mV/C Total Output Variation over Line, Load, Temperature Vref 4.9 - 5.1 4.82 - 5.18 V Output Noise Voltage (f = 10 Hz to 10 kHz, TJ = 25C) Vn - 50 - - 50 - V Long Term Stability (TA = 125C for 1000 Hours) S - 5.0 - - 5.0 - mV ISC - 30 - 85 - 180 - 30 - 85 - 180 mA 47 46 52 - 57 60 47 46 52 - 57 60 Characteristics REFERENCE SECTION Reference Output Voltage (IO = 1.0 mA, TJ = 25C) Output Short Circuit Current OSCILLATOR SECTION Frequency TJ = 25C TA = Tlow to Thigh fosc kHz Frequency Change with Voltage (VCC = 12 V to 25 V) fosc/V - 0.2 1.0 - 0.2 1.0 % Frequency Change with Temperature TA = Tlow to Thigh fosc/T - 5.0 - - 5.0 - % Vosc - 1.6 - - 1.6 - Oscillator Voltage Swing (Peak-to-Peak) Discharge Current (Vosc = 2.0 V) TJ = 25C TA = Tlow to Thigh Idischg V mA 7.5 7.2 8.4 - 9.3 9.5 7.5 7.2 8.4 - 9.3 9.5 2.45 2.5 2.55 2.42 2.5 2.58 ERROR AMPLIFIER SECTION Voltage Feedback Input (VO = 2.5 V) Input Bias Current (VFB = 2.7 V) Open Loop Voltage Gain (VO = 2.0 V to 4.0 V) Unity Gain Bandwidth (TJ = 25C) Power Supply Rejection Ratio (VCC = 12 V to 25 V) Output Current Sink (VO = 1.1 V, VFB = 2.7 V) Source (VO = 5.0 V, VFB = 2.3 V) Output Voltage Swing High State (RL = 15 k to ground, VFB = 2.3 V) Low State (RL = 15 k to Vref, VFB = 2.7 V) VFB V IIB - -0.1 -1.0 - -0.1 -2.0 A AVOL 65 90 - 65 90 - dB BW 0.7 1.0 - 0.7 1.0 - MHz PSRR 60 70 - 60 70 - dB ISink 2.0 -0.5 12 -1.0 - - 2.0 -0.5 12 -1.0 - - 5.0 - 6.2 0.8 - 1.1 5.0 - 6.2 0.8 - 1.1 mA ISource V VOH VOL 2. Adjust VCC above the Startup threshold before setting to 15 V. 3. Low duty cycle pulse techniques are used during test to maintain junction temperature as close to ambient as possible. Tlow = 0C for UC3842A, UC3843A Thigh = +70C for UC3842A, UC3843A -25C for UC2842A, UC2843A +85C for UC2842A, UC2843A http://onsemi.com 3 UC3842A, UC3843A, UC2842A, UC2843A ELECTRICAL CHARACTERISTICS (VCC = 15 V, [Note 4], RT = 10 k, CT = 3.3 nF, TA = Tlow to Thigh [Note 5], unless otherwise noted.) UC284XA Characteristics UC384XA Symbol Min Typ Max Min Typ Max Unit Current Sense Input Voltage Gain (Notes 6 & 7) AV 2.85 3.0 3.15 2.85 3.0 3.15 V/V Maximum Current Sense Input Threshold (Note 6) Vth 0.9 1.0 1.1 0.9 1.0 1.1 V - 70 - - 70 - IIB - -2.0 -10 - -2.0 -10 A tPLH(in/out) - 150 300 - 150 300 ns VOL - - 13 12 0.1 1.6 13.5 13.4 0.4 2.2 - - - - 13 12 0.1 1.6 13.5 13.4 0.4 2.2 - - - 0.1 1.1 - 0.1 1.1 CURRENT SENSE SECTION Power Supply Rejection Ratio VCC = 12 to 25 V (Note 6) Input Bias Current Propagation Delay (Current Sense Input to Output) PSRR dB OUTPUT SECTION Output Voltage Low State (ISink = 20 mA) Low State (ISink = 200 mA) High State (ISink = 20 mA) High State (ISink = 200 mA) Output Voltage with UVLO Activated VCC = 6.0 V, ISink = 1.0 mA V VOH VOL(UVLO) V Output Voltage Rise Time (CL = 1.0 nF, TJ = 25C) tr - 50 150 - 50 150 ns Output Voltage Fall Time (CL = 1.0 nF, TJ = 25C) tf - 50 150 - 50 150 ns 15 7.8 16 8.4 17 9.0 14.5 7.8 16 8.4 17.5 9.0 9.0 7.0 10 7.6 11 8.2 8.5 7.0 10 7.6 11.5 8.2 94 - 96 - - 0 94 - 96 - - 0 UNDERVOLTAGE LOCKOUT SECTION Startup Threshold UCX842A UCX843A Minimum Operating Voltage After Turn-On UCX842A UCX843A Vth V VCC(min) V PWM SECTION Duty Cycle Maximum Minimum % DCmax DCmin TOTAL DEVICE Power Supply Current (Note 4) Startup: (VCC = 6.5 V for UCX843A, (VCC = 14 V for UCX842A) Operating ICC Power Supply Zener Voltage (ICC = 25 mA) VZ mA - - 0.5 12 1.0 17 - - 0.5 12 1.0 17 30 36 - 30 36 - 4. Adjust VCC above the Startup threshold before setting to 15 V. 5. Low duty cycle pulse techniques are used during test to maintain junction temperature as close to ambient as possible. Tlow = 0C for UC3842A, UC3843A Thigh = +70C for UC3842A, UC3843A -25C for UC2842A, UC2843A +85C for UC2842A, UC2843A 6. This parameter is measured at the latch trip point with VFB = 0 V. V Output Compensation 7. Comparator gain is defined as: AV V Current Sense Input http://onsemi.com 4 V UC3842A, UC3843A, UC2842A, UC2843A 100 % DT, PERCENT OUTPUT DEADTIME 80 20 8.0 5.0 0.8 VCC = 15 V TA = 25C 10 k 20 k 50 k 100 k 200 k 500 k I dischg , DISCHARGE CURRENT (mA) 10 5.0 2.0 10 k 20 k 50 k 100 k 200 k 500 k fOSC, OSCILLATOR FREQUENCY (Hz) fOSC, OSCILLATOR FREQUENCY (Hz) Figure 2. Timing Resistor versus Oscillator Frequency Figure 3. Output Deadtime versus Oscillator Frequency 9.0 100 VCC = 15 V VOSC = 2.0 V 8.5 8.0 7.5 7.0 -55 20 1.0 1.0 M VCC = 15 V TA = 25C 50 -25 0 25 50 75 TA, AMBIENT TEMPERATURE (C) 100 125 90 VCC = 15 V CT = 3.3 nF TA = 25C 80 Idischg = 7.2 mA 70 60 50 40 800 1.0 k 2.0 k 3.0 k 4.0 k 6.0 k 8.0 k Figure 5. Maximum Output Duty Cycle versus Timing Resistor VCC = 15 V AV = -1.0 TA = 25C VCC = 15 V AV = -1.0 TA = 25C 3.0 V 20 mV/DIV 2.5 V Idischg = 9.5 mA RT, TIMING RESISTOR () Figure 4. Oscillator Discharge Current versus Temperature 2.55 V 1.0 M 200 mV/DIV 2.0 Dmax , MAXIMUM OUTPUT DUTY CYCLE (%) RT, TIMING RESISTOR (k ) 50 2.5 V 2.0 V 2.45 V 0.5 s/DIV 0.1 s/DIV Figure 6. Error Amp Small Signal Transient Response Figure 7. Error Amp Large Signal Transient Response http://onsemi.com 5 VCC = 15 V VO = 2.0 V to 4.0 V RL = 100 K TA = 25C 80 Gain 60 0 30 60 40 90 Phase 20 120 0 150 -20 10 100 1.0 k 10 k 100 k 1.0 M 180 10 M Vth, CURRENT SENSE INPUT THRESHOLD (V 100 , EXCESS PHASE (DEGREES) A VOL , OPEN LOOP VOLTAGE GAIN (dB) UC3842A, UC3843A, UC2842A, UC2843A 1.2 VCC = 15 V 1.0 0.8 TA = 25C 0.6 TA = 125C 0.4 TA = -55C 0.2 0 2.0 4.0 6.0 VO, ERROR AMP OUTPUT VOLTAGE (V) 0 f, FREQUENCY (Hz) Figure 9. Current Sense Input Threshold versus Error Amp Output Voltage ISC, REFERENCE SHORT CIRCUIT CURRENT (mA) V ref , REFERENCE VOLTAGE CHANGE (mV) Figure 8. Error Amp Open Loop Gain and Phase versus Frequency 110 0 VCC = 15 V -4.0 -8.0 -12 -16 TA = 125C -20 TA = 55C TA = 25C 20 40 60 80 100 120 90 70 50 -55 -25 0 25 50 75 100 Iref, REFERENCE SOURCE CURRENT (mA) TA, AMBIENT TEMPERATURE (C) Figure 10. Reference Voltage Change versus Source Current Figure 11. Reference Short Circuit Current versus Temperature VCC = 15 V IO = 1.0 mA to 20 mA TA = 25C VCC = 12 V to 25 V TA = 25C O V O V VCC = 15 V RL 0.1 , OUTPUT VOLTAGE CHANGE (2.0 mV/DIV) 0 , OUTPUT VOLTAGE CHANGE (2.0 mV/DIV) -24 8.0 2.0 ms/DIV 2.0 ms/DIV Figure 13. Reference Line Regulation Figure 12. Reference Load Regulation http://onsemi.com 6 125 0 Source Saturation (Load to Ground) VCC -1.0 TA = 25C -2.0 VCC = 15 V 80 s Pulsed Load 120 Hz Rate VCC = 15 V CL = 1.0 nF TA = 25C 90% TA = -55C 3.0 TA = -55C 2.0 TA = 25C 1.0 0 Sink Saturation (Load to VCC) 0 10% GND 200 400 600 IO, OUTPUT LOAD CURRENT (mA) 50 ns/DIV 800 Figure 15. Output Waveform 20 15 10 UCX843A I CC , SUPPLY CURRENT (mA) 25 20 V/DIV VCC = 30 V CL = 15 pF TA = 25C 100 mA/DIV I CC , SUPPLY CURRENT V O , OUTPUT VOLTAGE Figure 14. Output Saturation Voltage versus Load Current 5 RT = 10 k CT = 3.3 nF VFB = 0 V ISense = 0 V TA = 25C UCX842A V sat , OUTPUT SATURATION VOLTAGE (V) UC3842A, UC3843A, UC2842A, UC2843A 0 0 100 ns/DIV 10 20 30 VCC , SUPPLY VOLTAGE Figure 16. Output Cross Conduction Figure 17. Supply Current versus Supply Voltage http://onsemi.com 7 40 UC3842A, UC3843A, UC2842A, UC2843A VCC VCC Vref 8(14) R Internal Bias 2.5V RT R 3.6V + + - - 7(12) 36V + Reference Regulator VCC UVLO - Vin + - VC 7(11) Vref UVLO Output Q1 Oscillator 4(7) + CT Voltage Feedback Input 2(3) Output Compensation 1(1) 6(10) T Q 1.0mA Power Ground S + - - + 2R Error Amplifier R Q R 5(8) PWM Latch Current Sense Input 1.0V Current Sense Comparator GND 5(9) 3(5) + - = Sink Only Positive True Logic Pin numbers in parenthesis are for the D suffix SOIC-14 package. Figure 18. Representative Block Diagram Capacitor CT Latch ``Set'' Input Output/ Compensation Current Sense Input Latch ``Reset'' Input Output Large RT/Small CT Small RT/Large CT Figure 19. Timing Diagram http://onsemi.com 8 RS UC3842A, UC3843A, UC2842A, UC2843A OPERATING DESCRIPTION The UC3842A, UC3843A series are high performance, fixed frequency, current mode controllers. They are specifically designed for Off-Line and DC-to-DC converter applications offering the designer a cost effective solution with minimal external components. A representative block diagram is shown in Figure 18. is removed, or at the beginning of a soft-start interval (Figures 24, 25). The Error Amp minimum feedback resistance is limited by the amplifier's source current (0.5 mA) and the required output voltage (VOH) to reach the comparator's 1.0 V clamp level: Rf(min) Oscillator The oscillator frequency is programmed by the values selected for the timing components RT and CT. Capacitor CT is charged from the 5.0 V reference through resistor RT to approximately 2.8 V and discharged to 1.2 V by an internal current sink. During the discharge of CT, the oscillator generates and internal blanking pulse that holds the center input of the NOR gate high. This causes the Output to be in a low state, thus producing a controlled amount of output deadtime. Figure 2 shows RT versus Oscillator Frequency and Figure 3, Output Deadtime versus Frequency, both for given values of CT. Note that many values of RT and CT will give the same oscillator frequency but only one combination will yield a specific output deadtime at a given frequency. The oscillator thresholds are temperature compensated, and the discharge current is trimmed and guaranteed to within 10% at TJ = 25C. These internal circuit refinements minimize variations of oscillator frequency and maximum output duty cycle. The results are shown in Figures 4 and 5. In many noise sensitive applications it may be desirable to frequency-lock the converter to an external system clock. This can be accomplished by applying a clock signal to the circuit shown in Figure 21. For reliable locking, the free-running oscillator frequency should be set about 10% less than the clock frequency. A method for multi unit synchronization is shown in Figure 22. By tailoring the clock waveform, accurate Output duty cycle clamping can be achieved. 3.0 (1.0 V) + 1.4 V = 8800 0.5 mA Current Sense Comparator and PWM Latch The UC3842A, UC3843A operate as a current mode controller, whereby output switch conduction is initiated by the oscillator and terminated when the peak inductor current reaches the threshold level established by the Error Amplifier Output/Compensation (Pin 1). Thus the error signal controls the peak inductor current on a cycle-by-cycle basis. The current Sense Comparator PWM Latch configuration used ensures that only a single pulse appears at the Output during any given oscillator cycle. The inductor current is converted to a voltage by inserting the ground referenced sense resistor RS in series with the source of output switch Q1. This voltage is monitored by the Current Sense Input (Pin 3) and compared a level derived from the Error Amp Output. The peak inductor current under normal operating conditions is controlled by the voltage at pin 1 where: Ipk = V(Pin 1) - 1.4 V 3 RS Abnormal operating conditions occur when the power supply output is overloaded or if output voltage sensing is lost. Under these conditions, the Current Sense Comparator threshold will be internally clamped to 1.0 V. Therefore the maximum peak switch current is: Ipk(max) = 1.0 V RS When designing a high power switching regulator it becomes desirable to reduce the internal clamp voltage in order to keep the power dissipation of RS to a reasonable level. A simple method to adjust this voltage is shown in Figure 23. The two external diodes are used to compensate the internal diodes yielding a constant clamp voltage over temperature. Erratic operation due to noise pickup can result if there is an excessive reduction of the Ipk(max) clamp voltage. A narrow spike on the leading edge of the current waveform can usually be observed and may cause the power supply to exhibit an instability when the output is lightly loaded. This spike is due to the power transformer interwinding capacitance and output rectifier recovery time. The addition of an RC filter on the Current Sense Input with a time constant that approximates the spike duration will usually eliminate the instability; refer to Figure 27. Error Amplifier A fully compensated Error Amplifier with access to the inverting input and output is provided. It features a typical dc voltage gain of 90 dB, and a unity gain bandwidth of 1.0 MHz with 57 degrees of phase margin (Figure 8). The noninverting input is internally biased at 2.5 V and is not pinned out. The converter output voltage is typically divided down and monitored by the inverting input. The maximum input bias current is -2.0 A which can cause an output voltage error that is equal to the product of the input bias current and the equivalent input divider source resistance. The Error Amp Output (Pin 1) is provide for external loop compensation (Figure 31). The output voltage is offset by two diode drops ( 1.4 V) and divided by three before it connects to the inverting input of the Current Sense Comparator. This guarantees that no drive pulses appear at the Output (Pin 6) when Pin 1 is at its lowest state (VOL). This occurs when the power supply is operating and the load http://onsemi.com 9 UC3842A, UC3843A, UC2842A, UC2843A PIN FUNCTION DESCRIPTION Pin 8-Pin 14-Pin Function 1 1 Compensation 2 3 Voltage Feedback This is the inverting input of the Error Amplifier. It is normally connected to the switching power supply output through a resistor divider. 3 5 Current Sense A voltage proportional to inductor current is connected to this input. The PWM uses this information to terminate the output switch conduction. 4 7 RT/CT The Oscillator frequency and maximum Output duty cycle are programmed by connecting resistor RT to Vref and capacitor CT to ground. Operation to 500 kHz is possible. 5 - GND This pin is the combined control circuitry and power ground (8-pin package only). 6 10 Output 7 12 VCC This pin is the positive supply of the control IC. 8 14 Vref This is the reference output. It provides charging current for capacitor CT through resistor RT. - 8 Power Ground - 11 VC - 9 GND - 2,4,6,13 NC Description This pin is Error Amplifier output and is made available for loop compensation. This output directly drives the gate of a power MOSFET. Peak currents up to 1.0 A are sourced and sunk by this pin. This pin is a separate power ground return (14-pin package only) that is connected back to the power source. It is used to reduce the effects of switching transient noise on the control circuitry. The Output high state (VOH) is set by the voltage applied to this pin (14-pin package only). With a separate power source connection, it can reduce the effects of switching transient noise on the control circuitry. This pin is the control circuitry ground return (14-pin package only) and is connected back to the power source ground. No connection (14-pin package only). These pins are not internally connected. Undervoltage Lockout and has a typical rise and fall time of 50 ns with a 1.0 nF load. Additional internal circuitry has been added to keep the Output in a sinking mode whenever an undervoltage lockout is active. This characteristic eliminates the need for an external pull-down resistor. The SOIC-14 surface mount package provides separate pins for VC (output supply) and Power Ground. Proper implementation will significantly reduce the level of switching transient noise imposed on the control circuitry. This becomes particularly useful when reducing the Ipk(max) clamp level. The separate VC supply input allows the designer added flexibility in tailoring the drive voltage independent of VCC. A zener clamp is typically connected to this input when driving power MOSFETs in systems where VCC is greater than 20 V. Figure 26 shows proper power and control ground connections in a current sensing power MOSFET application. Two undervoltage lockout comparators have been incorporated to guarantee that the IC is fully functional before the output stage is enabled. The positive power supply terminal (VCC) and the reference output (Vref) are each monitored by separate comparators. Each has built-in hysteresis to prevent erratic output behavior as their respective thresholds are crossed. The VCC comparator upper and lower thresholds are 16 V/10 V for the UCX842A, and 8.4 V/7.6 V for the UCX843A. The Vref comparator upper and lower thresholds are 3.6V/3.4 V. The large hysteresis and low startup current of the UCX842A makes it ideally suited in off-line converter applications where efficient bootstrap startup techniques are required (Figure 34). The UCX843A is intended for lower voltage dc to dc converter applications. A 36 V zener is connected as a shunt regulator form VCC to ground. Its purpose is to protect the IC from excessive voltage that can occur during system startup. The minimum operating voltage for the UCX842A is 11 V and 8.2 V for the UCX843A. Reference The 5.0 V bandgap reference is trimmed to 1.0% tolerance at TJ = 25C on the UC284XA, and 2.0% on the UC384XA. Its primary purpose is to supply charging current to the oscillator timing capacitor. The reference has short circuit protection and is capable of providing in excess of 20 mA for powering additional control system circuitry. Output These devices contain a single totem pole output stage that was specifically designed for direct drive of power MOSFETs. It is capable of up to 1.0 A peak drive current http://onsemi.com 10 UC3842A, UC3843A, UC2842A, UC2843A DESIGN CONSIDERATIONS Do not attempt to construct the converter on wire-wrap or plug-in prototype boards. High Frequency circuit layout techniques are imperative to prevent pulse width jitter. This is usually caused by excessive noise pick-up imposed on the Current Sense or Voltage Feedback inputs. Noise immunity can be improved by lowering circuit impedances at these points. The printed circuit layout should contain a ground plane with low-current signal and high-current switch and output grounds returning on separate paths back to the input filter capacitor. Ceramic bypass capacitors (0.1 F) connected directly to VCC, VC, and Vref may be required depending upon circuit layout. This provides a low impedance path for filtering the high frequency noise. All high current loops should be kept as short as possible using heavy copper runs to minimize radiated EMI. The Error Amp compensation circuitry and the converter output voltage divider should be located close to the IC and as far as possible from the power switch and other noise generating components. Current mode converters can exhibit subharmonic oscillations when operating at a duty cycle greater than 50% with continuous inductor current. This instability is independent of the regulators closed-loop characteristics and is caused by the simultaneous operating conditions of fixed frequency and peak current detecting. Figure 20A shows the phenomenon graphically. At t0, switch conduction begins, causing the inductor current to rise at a slope of m1. This slope is a function of the input voltage divided by the inductance. At t1, the Current Sense Input reaches the threshold established by the control voltage. This causes the switch to turn off and the current to decay at a slope of m2 until the next oscillator cycle. The unstable condition can be shown if a perturbation is added to the control voltage, resulting in a small I (dashed line). With a fixed oscillator period, the current decay time is reduced, and the minimum current at switch turn-on (t2) is increased by I + I m2/m1. The minimum current at the next cycle (t3) decreases to (I + I m2/m1) (m2/m1). This perturbation is multiplied by m2.m1 on each succeeding cycle, alternately increasing and decreasing the inductor current at switch turn-on. Several oscillator cycles may be required before the inductor current reaches zero causing the process to commence again. If m2/m1 is greater than 1, the converter will be unstable. Figure 20B shows that by adding an artificial ramp that is synchronized with the PWM clock to the control voltage, the I perturbation will decrease to zero on succeeding cycles. This compensation ramp (m3) must have a slope equal to or slightly greater than m2/2 for stability. With m2/2 slope compensation, the average inductor current follows the control voltage yielding true current mode operation. The compensating ramp can be derived from the oscillator and added to either the Voltage Feedback or Current Sense inputs (Figure 33). (A) I Control Voltage m2 m1 Inductor Current I + I m2 m1 m2 I + I m 1 Oscillator Period t1 t0 m2 m1 t3 t2 (B) Control Voltage I m3 m1 m2 Inductor Current Oscillator Period t4 t5 Figure 20. Continuous Current Waveforms http://onsemi.com 11 t6 UC3842A, UC3843A, UC2842A, UC2843A Vref 8(14) R Bias RT RB 6 CT 4(7) 47 2(3) 5 2 + - 2R R EA 5.0k 0.01 + 5.0k + - + - Bias R Osc R 3 Q S + - 7 2(3) 1(1) 5(9) 1.44 f= (RA + 2RB)C The diode clamp is required if the Sync amplitude is large enough to cause the bottom side of CT to go more than 300 mV below ground. VCC + - + R Bias R + + - 2(3) 7(11) - Osc R2 - + - + 8(14) R Bias 6(10) R S 1.0mA Q R Comp/Latch - + 2R R + 4(7) + - RS 2(3) 1.0M 5(9) 1.67 R2 R1 + 0.33 x 10 - 3 R1 R2 R1 + R2 VClamp RS Ipk(max) = +1 C 2R R EA Vin 7(12) R Bias R 5(9) + Osc + 4(7) + - 2(3) 5.0Vref 7(11) Q1 1.0mA - + 2R R R2 S Q R Comp/Latch 1.0V R1 VClamp = 1.67 R1 Ipk(max) = +1 VClamp RS tSoftstart = - In (11) 3(5) Control CIrcuitry Ground: To Pin (9) RS Ipk rDS(on) rDM(on) + RS S M K (8) (5) 5(9) R2 - + - S Q - R + Comp/Latch RS MPSA63 + (10) G 5(8) 1(1) C + - VPin 5 = If: SENSEFET = MTP10N10M RS = 200 Then: Vpin 5 = 0.075 Ipk D SENSEFET - 6(10) VClamp EA + - Vin (12) + - + - Q 1.0V VCC 8(14) R Figure 24. Soft-Start Circuit VCC + - - + 1(1) Figure 23. Adjustable Reduction of Clamp Level 5.0Vref S 1.0mA tSoft-Start 3600C in F Where: 0 VClamp 1.0 V + - - Osc 3(5) 1(1) VClamp = + 5(8) 1.0V R1 5.0Vref Q1 VClamp EA RA + 2RB Vin 7(12) 5.0Vref Dmax = 5(9) To Additional UCX84XA's RB Figure 22. External Duty Cycle Clamp and Multi Unit Synchronization Figure 21. External Clock Synchronization 4(7) 2R R EA 1 1(1) 8(14) + 4(7) 5.0k MC1455 C R 4 8 Osc External Sync Input 8(14) RA R RS 1/4 W Power Ground To Input Source Return Where: 0 VClamp 1.0 V 1- VC 3VClamp C R1 R2 R1 + R2 Figure 25. Adjustable Buffered Reduction of Clamp Level with Soft-Start Virtually lossless current sensing can be achieved with the implementation of a SENSEFET power switch. For proper operation during over current conditions, a reduction of the Ipk(max) clamp level must be implemented. Refer to Figures 23 and 25. Figure 26. Current Sensing Power MOSFET http://onsemi.com 12 UC3842A, UC3843A, UC2842A, UC2843A VCC VCC Vin 7(12) + - 5.0Vref + + - 5.0Vref + - + - 7(11) + - + - + 7(11) - + Q1 6(10) 6(10) S Rg - Q1 - Vin 7(12) S Q 5(8) R Comp/Latch Q R Comp/Latch - + R 5(8) 3(5) 3(5) C RS RS Series gate resistor Rg will damp any high frequency parasitic oscillations caused by the MOSFET input capacitance and any series wiring inductance in the gate-source circuit. The addition of the RC filter will eliminate instability caused by the leading edge spike on the current waveform. Figure 27. Current Waveform Spike Suppression IB Figure 28. MOSFET Parasitic Oscillations Vin + VCC Vin 7(12) 0 Base Charge Removal - 5.0Vref C1 + Q1 + - Isolation Boundary + - + - + 0 - - 6(1) 6(1) 5(8) S Q - R + Comp/Latch 3(5) 50% DC Ipk = 5(8) R RS EE E E E EE VGS Waveforms Q1 7(11) 3(5) C NS RS + 0 - 25% DC V(pin 1) - 1.4 3 RS Np The totem-pole output can furnish negative base current for enhanced transistor turn-off, with the addition of capacitor C1. Figure 29. Bipolar Transistor Drive Figure 30. Isolated MOSFET Drive From VO 2.5V Ri 8(14) R Rd Bias 2(3) CI + 1.0mA + - 2R R EA Rf R 1(1) Osc + - 2(3) 5(9) + 4(7) 1.0mA EA Error Amp compensation circuit for stabilizing any current-mode topology except for boost and flyback converters operating with continuous inductor current. 2R R From VO 2.5V 1(1) MCR 101 2N 3905 Rp 5(9) 2N 3903 Cp 2(3) Ri Rd CI Rf + - + 1.0mA EA 2R R 1(1) 5(9) The MCR101 SCR must be selected for a holding of less than 0.5 mA at TA(min). The simple two transistor circuit can be used in place of the SCR as shown. All resistors are 10 k. Error Amp compensation circuit for stabilizing current-mode boost and flyback topologies operating with continuous inductor current. Figure 31. Latched Shutdown Figure 32. Error Amplifier Compensation http://onsemi.com 13 NP NS UC3842A, UC3843A, UC2842A, UC2843A VCC Vin 7(12) 8(14) + - 5.0Vref R RT Bias MPS3904 R RSlope - + - 7(11) - 4(7) Osc From VO CT Ri 2(3) Rd + + Cf + 6(10) -m 1.0mA + - S - + 2R R EA Rf R Q 5(8) Comp/Latch 1.0V 3(5) m 1(1) RS -3.0 m 5(9) The buffered oscillator ramp can be resistively summed with either the voltage feedback or current sense inputs to provide slope compensation. Figure 33. Slope Compensation 4.7 + MDA 202 3300pF 4.7k 250 T1 1N4935 + 68 + + - 5.0Vref 0.01 Bias + Osc 2.7k 6(10) 18k 150k 12V/0.3A + -12V/0.3A L3 1N4937 22 + + - 10 + MUR110 680pF 7(11) 4(7) 4700pF + + + - 5.0V/4.0A 12V RTN 1000 1N4937 10k L2 10 47 100 8(14) 100pF + 5.0V RTN + 1000 7(12) 4.7k 1000 MUR110 1N4935 2(3) + 2200 56k 115Va c L1 MBR1635 S - + EA Q R 5(8) Comp/Latch 3(5) MTP 4N50 1.0k 470pF 1(1) 0.5 5(9) Figure 34. 27 Watt Off-Line Flyback Regulator Test Conditions L1 - 15 H at 5.0 A, Coilcraft Z7156. L2, L3 - 25 H at 1.0 A, Coilcraft Z7157. T1 - Primary: 45 Turns # 26 AWG T1 - Secondary 12 V: 9 Turns # 30 AWG T1 - (2 strands) Bifiliar Wound T1 - Secondary 5.0 V: 4 Turns (six strands) T1 - #26 Hexfiliar Wound T1 - Secondary Feedback: 10 Turns #30 AWG T1 - (2 strands) Bifiliar Wound T1 - Core: Ferroxcube EC35-3C8 T1 - Bobbin: Ferroxcube EC35PCB1 T1 - Gap 0.01" for a primary inductance of 1.0 mH Results Line Regulation: 5.0 V 12 V Vin = 95 Vac to 130 Vac = 50 mV or 0.5% = 24 mV or 0.1% Load Regulation: 5.0 V 12 V Vin = 115 Vac, Iout = 1.0 A to 4.0 A Vin = 115 Vac, Iout = 100 mA to 300 mA = 300 mV or 3.0% = 60 mV or 0.25% Output Ripple: Vin = 115 Vac 40 mVpp 80 mVpp Vin = 115 Vac 70% Efficiency 5.0 V 12 V All outputs are at nominal load currents, unless otherwise noted. http://onsemi.com 14 UC3842A, UC3843A, UC2842A, UC2843A ORDERING INFORMATION Device Operating Temperature Range UC3842AN Package Shipping PDIP-8 UC3842ANG PDIP-8 (Pb-Free) UC3842AN2 PDIP-8 50 Units / Rail UC3842AN2G PDIP-8 (Pb-Free) UC3842AD SOIC-14 55 Units / Rail UC3842ADG SOIC-14 (Pb-Free) 55 Units / Rail UC3842ADR2 SOIC-14 2500 / Tape & Reel UC3842ADR2G SOIC-14 (Pb-Free) 2500 / Tape & Reel UC3843AN PDIP-8 UC3843ANG PDIP-8 (Pb-Free) UC3843AN2 PDIP-8 UC3843AN2G TA = 0 to +70C 50 Units / Rail PDIP-8 (Pb-Free) UC3843AD SOIC-14 55 Units / Rail UC3843ADG SOIC-14 (Pb-Free) 55 Units / Rail UC3843ADR2 SOIC-14 2500 / Tape & Reel UC3843ADR2G SOIC-14 (Pb-Free) 2500 / Tape & Reel SOIC-8 98 Units / Rail UC3843AD1G SOIC-8 (Pb-Free) 98 Units / Rail UC3843AD1R2 SOIC-8 UC3843AD1 UC3843AD1R2G SOIC-8 (Pb-Free) UC3843AD2R2 SOIC-14 UC3843AD2R2G SOIC-14 (Pb-Free) 2500 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 15 UC3842A, UC3843A, UC2842A, UC2843A ORDERING INFORMATION Package Shipping PDIP-8 50 Units / Rail UC2842ANG PDIP-8 (Pb-Free) 50 Units / Rail UC2842AD SOIC-14 55 Units / Rail UC2842ADG SOIC-14 (Pb-Free) 55 Units / Rail UC2842ADR2 SOIC-14 2500 / Tape & Reel UC2842ADR2G SOIC-14 (Pb-Free) 2500 / Tape & Reel PDIP-8 50 Units / Rail PDIP-8 (Pb-Free) 50 Units / Rail SOIC-14 55 Units / Rail UC2843ADG SOIC-14 (Pb-Free) 55 Units / Rail UC2843ADR2 SOIC-14 2500 / Tape & Reel UC2843ADR2G SOIC-14 (Pb-Free) 2500 / Tape & Reel SOIC-8 98 Units / Rail UC2843AD1G SOIC-8 (Pb-Free) 98 Units / Rail UC2843AD1R2 SOIC-8 2500 / Tape & Reel SOIC-8 (Pb-Free) 2500 / Tape & Reel Device Operating Temperature Range UC2842AN UC2843AN UC2843ANG TA = -25 to +85C UC2843AD UC2843AD1 UC2843AD1R2G For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. MARKING DIAGRAMS PDIP-8 N SUFFIX CASE 626 8 SOIC-14 D SUFFIX CASE 751A 14 UCx84xAN AWL YYWWG SOIC-8 D1 SUFFIX CASE 751 8 x843 ALYW G UCx84xADG AWLYWW 1 1 1 x A WL, L YY, Y WW, W G or G = 2 or 3 = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package http://onsemi.com 16 UC3842A, UC3843A, UC2842A, UC2843A PACKAGE DIMENSIONS PDIP-8 N SUFFIX CASE 626-05 ISSUE L 8 NOTES: 1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS). 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5 -B- 1 4 DIM A B C D F G H J K L M N F -A- NOTE 2 L C J -T- MILLIMETERS MIN MAX 9.40 10.16 6.10 6.60 3.94 4.45 0.38 0.51 1.02 1.78 2.54 BSC 0.76 1.27 0.20 0.30 2.92 3.43 7.62 BSC --- 10 _ 0.76 1.01 INCHES MIN MAX 0.370 0.400 0.240 0.260 0.155 0.175 0.015 0.020 0.040 0.070 0.100 BSC 0.030 0.050 0.008 0.012 0.115 0.135 0.300 BSC --- 10_ 0.030 0.040 N SEATING PLANE D M K G H 0.13 (0.005) M T A M B M SOIC-14 D SUFFIX CASE 751A-03 ISSUE G -A- 14 8 -B- P 7 PL 0.25 (0.010) M B M 7 1 G F R X 45 _ C -T- SEATING PLANE D 14 PL 0.25 (0.010) M T B J M K S A S http://onsemi.com 17 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. DIM A B C D F G J K M P R MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.228 0.244 0.010 0.019 UC3842A, UC3843A, UC2842A, UC2843A PACKAGE DIMENSIONS SOIC-8 D1 SUFFIX CASE 751-07 ISSUE AG NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751-01 THRU 751-06 ARE OBSOLETE. NEW STANDARD IS 751-07. -X- A 8 5 S B 1 0.25 (0.010) M Y M 4 K -Y- G C N X 45 _ DIM A B C D G H J K M N S SEATING PLANE -Z- 0.10 (0.004) H D 0.25 (0.010) M Z Y S X M J S MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. SENSEFET is a trademark of Semiconductor Components Industries, LLC. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: N. American Technical Support: 800-282-9855 Toll Free Literature Distribution Center for ON Semiconductor USA/Canada P.O. Box 61312, Phoenix, Arizona 85082-1312 USA Phone: 480-829-7710 or 800-344-3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Fax: 480-829-7709 or 800-344-3867 Toll Free USA/Canada Phone: 81-3-5773-3850 Email: orderlit@onsemi.com http://onsemi.com 18 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. UC3842A/D