EVB-LAN7430 Evaluation Board User's Guide 2019 Microchip Technology Inc. DS50002841A Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights unless otherwise stated. Trademarks The Microchip name and logo, the Microchip logo, AnyRate, AVR, AVR logo, AVR Freaks, BitCloud, chipKIT, chipKIT logo, CryptoMemory, CryptoRF, dsPIC, FlashFlex, flexPWR, Heldo, JukeBlox, KeeLoq, Kleer, LANCheck, LINK MD, maXStylus, maXTouch, MediaLB, megaAVR, MOST, MOST logo, MPLAB, OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, Prochip Designer, QTouch, SAM-BA, SpyNIC, SST, SST Logo, SuperFlash, tinyAVR, UNI/O, and XMEGA are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. ClockWorks, The Embedded Control Solutions Company, EtherSynch, Hyper Speed Control, HyperLight Load, IntelliMOS, mTouch, Precision Edge, and Quiet-Wire are registered trademarks of Microchip Technology Incorporated in the U.S.A. Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, BodyCom, CodeGuard, CryptoAuthentication, CryptoAutomotive, CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial Programming, ICSP, INICnet, Inter-Chip Connectivity, JitterBlocker, KleerNet, KleerNet logo, memBrain, Mindi, MiWi, motorBench, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE, Ripple Blocker, SAM-ICE, Serial Quad I/O, SMART-I.S., SQI, SuperSwitcher, SuperSwitcher II, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. (c) 2019, Microchip Technology Incorporated, All Rights Reserved. ISBN: 978-1-5224-4070-3 QUALITYMANAGEMENTSYSTEM CERTIFIEDBYDNV == ISO/TS16949== DS50002841A-page 2 Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. 2019 Microchip Technology Inc. EVB-LAN7430 EVALUATION BOARD USER'S GUIDE Table of Contents Preface ........................................................................................................................... 5 Introduction............................................................................................................ 5 Document Layout .................................................................................................. 5 Conventions Used in this Guide ............................................................................ 6 The Microchip Web Site ........................................................................................ 7 Development Systems Customer Change Notification Service ............................ 7 Customer Support ................................................................................................. 8 Document Revision History ................................................................................... 8 Chapter 1. Overview 1.1 Introduction ..................................................................................................... 9 1.2 References ................................................................................................... 10 1.3 Terms and Abbreviations ............................................................................. 10 Chapter 2. Board Details and Configuration 2.1 Board Details ................................................................................................ 11 2.1.1 Power ........................................................................................................ 11 2.1.2 Resets ....................................................................................................... 11 2.1.3 Clock ......................................................................................................... 11 2.1.4 Configuration ............................................................................................. 11 Chapter 3. Using the EVB-LAN7430 Appendix A. EVB-LAN7430 Evaluation Board A.1 Introduction .................................................................................................. 15 Appendix B. Schematics B.1 Introduction .................................................................................................. 17 Appendix C. Bill of Materials C.1 Introduction .................................................................................................. 19 Worldwide Sales and Service .................................................................................... 22 2019 Microchip Technology Inc. DS50002841A-page 3 EVB-LAN7430 Evaluation Board User's Guide NOTES: DS50002841A-page 4 2019 Microchip Technology Inc. EVB-LAN7430 EVALUATION BOARD USER'S GUIDE Preface NOTICE TO CUSTOMERS All documentation becomes dated, and this manual is no exception. Microchip tools and documentation are constantly evolving to meet customer needs, so some actual dialogs and/or tool descriptions may differ from those in this document. Please refer to our web site (www.microchip.com) to obtain the latest documentation available. Documents are identified with a "DS" number. This number is located on the bottom of each page, in front of the page number. The numbering convention for the DS number is "DSXXXXXA", where "XXXXX" is the document number and "A" is the revision level of the document. For the most up-to-date information on development tools, see the MPLAB(R) IDE online help. Select the Help menu, and then Topics to open a list of available online help files. INTRODUCTION This chapter contains general information that will be useful to know before using the EVB-LAN7430 Evaluation Board. Items discussed in this chapter include: * * * * * * Document Layout Conventions Used in this Guide The Microchip Web Site Development Systems Customer Change Notification Service Customer Support Document Revision History DOCUMENT LAYOUT This document describes how to use the EVB-LAN7430 Evaluation Board as a high-performance and low-cost USB/Ethernet connectivity solution. The manual layout is as follows: * Chapter 1. "Overview" - Shows a brief description of the EVB-LAN7430 Evaluation Board. * Chapter 2. "Board Details and Configuration" - Includes information about the EVB-LAN7430 Evaluation Board. * Chapter 3. "Using the EVB-LAN7430" - Includes information on how to use the EVB-LAN7430 Evaluation Board. * Appendix A. "EVB-LAN7430 Evaluation Board" - This appendix shows the EVB-LAN7430 Evaluation Board schematic. * Appendix B. "Schematics" - This appendix shows the EVB-LAN7430 Evaluation Board schematic. * Appendix C. "Bill of Materials" - This appendix includes the EVB-LAN7430 Evaluation Board Bill of Materials (BOM). 2019 Microchip Technology Inc. DS50002841A-page 5 EVB-LAN7430 Evaluation Board User's Guide CONVENTIONS USED IN THIS GUIDE This manual uses the following documentation conventions: DOCUMENTATION CONVENTIONS Description Represents Examples Arial font: MPLAB(R) IDE User's Guide Italic characters Referenced books Emphasized text ...is the only compiler... Initial caps A window the Output window A dialog the Settings dialog A menu selection select Enable Programmer Quotes A field name in a window or dialog "Save project before build" Underlined, italic text with right angle bracket A menu path File>Save Bold characters A dialog button Click OK A tab Click the Power tab N`Rnnnn A number in verilog format, 4`b0010, 2`hF1 where N is the total number of digits, R is the radix and n is a digit. Text in angle brackets < > A key on the keyboard Press <Enter>, <F1> Courier New font: Plain Courier New DS50002841A-page 6 Sample source code #define START Filenames autoexec.bat File paths c:\mcc18\h Keywords _asm, _endasm, static Command-line options -Opa+, -Opa- Bit values 0, 1 Constants 0xFF, `A' Italic Courier New A variable argument file.o, where file can be any valid filename Square brackets [ ] Optional arguments mcc18 [options] file [options] Curly brackets and pipe character: { | } Choice of mutually exclusive arguments; an OR selection errorlevel {0|1} Ellipses... Replaces repeated text var_name [, var_name...] Represents code supplied by user void main (void) { ... } 2019 Microchip Technology Inc. Preface THE MICROCHIP WEB SITE Microchip provides online support via our web site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: * Product Support - Data sheets and errata, application notes and sample programs, design resources, user's guides and hardware support documents, latest software releases and archived software * General Technical Support - Frequently Asked Questions (FAQs), technical support requests, online discussion groups, Microchip consultant program member listing * Business of Microchip - Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives DEVELOPMENT SYSTEMS CUSTOMER CHANGE NOTIFICATION SERVICE Microchip's customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at www.microchip.com, click on Customer Change Notification and follow the registration instructions. The Development Systems product group categories are: * Compilers - The latest information on Microchip C compilers, assemblers, linkers and other language tools. These include all MPLAB C compilers; all MPLAB assemblers (including MPASM assembler); all MPLAB linkers (including MPLINK object linker); and all MPLAB librarians (including MPLIB object librarian). * Emulators - The latest information on Microchip in-circuit emulators.This includes the MPLAB REAL ICE and MPLAB ICE 2000 in-circuit emulators. * In-Circuit Debuggers - The latest information on the Microchip in-circuit debuggers. This includes MPLAB ICD 3 in-circuit debuggers and PICkit 3 debug express. * MPLAB IDE - The latest information on Microchip MPLAB IDE, the Windows Integrated Development Environment for development systems tools. This list is focused on the MPLAB IDE, MPLAB IDE Project Manager, MPLAB Editor and MPLAB SIM simulator, as well as general editing and debugging features. * Programmers - The latest information on Microchip programmers. These include production programmers such as MPLAB REAL ICE in-circuit emulator, MPLAB ICD 3 in-circuit debugger and MPLAB PM3 device programmers. Also included are nonproduction development programmers such as PICSTART Plus and PIC-kit 2 and 3. 2019 Microchip Technology Inc. DS50002841A-page 7 EVB-LAN7430 Evaluation Board User's Guide CUSTOMER SUPPORT Users of Microchip products can receive assistance through several channels: * * * * Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://www.microchip.com/support DOCUMENT REVISION HISTORY Revisions DS50002841A (01-18-19) DS50002841A-page 8 Section/Figure/Entry Correction Initial release 2019 Microchip Technology Inc. EVB-LAN7430 EVALUATION BOARD USER'S GUIDE Chapter 1. Overview 1.1 INTRODUCTION The EVB-LAN7430 Evaluation Board features LAN7430, PCIe to Gigabit Ethernet bridge device. LAN7430 has an integrated 10/100/1000 Mbps Ethernet PHY, PCIe PHY, Gigabit Ethernet MAC, OTP memory, EEPROM controller, clock/reset/power management functions, PCIe endpoint controller, DMA controller and JTAG TAP. The device supports IEEE 802.3az Energy Efficient Ethernet (EEE), IEEE 1588-2008, and advanced power management features, which makes this device highly suitable across many application areas. This evaluation board requires a single lane PCIe slot. The scope of this document is to describe the EVB-LAN7430 evaluation board setup and the corresponding jumper configuration. A simplified block diagram of the board is shown in Figure 1-1. FIGURE 1-1: EVB-LAN7430 BLOCK DIAGRAM PTP SMA Connectors LEDs GPIO EEPROM LED/EEPROM JTAG Test Points RJ-45 GbE PHY LAN7430 Clock JTAG TAP Clock Source PCIe PHY PCIe Edge Connector 2019 Microchip Technology Inc. DS50002841A-page 9 EVB-LAN7430 Evaluation Board User's Guide 1.2 REFERENCES Concepts and material available in the following documents will be helpful when reading this document. Visit www.microchip.com for the latest documentation. * LAN7430 Data Sheet * EVB-LAN7430 Schematic * Application Note: Implementing IEEE 1588-2008 with LAN7430 1.3 TERMS AND ABBREVIATIONS * * * * * * DS50002841A-page 10 EEE - Energy Efficient Ethernet EVB - Evaluation Board GND - Ground PHY - Physical Transceiver PTP - Point to Point SMA Connector - Sub-Miniature version A Connector 2019 Microchip Technology Inc. EVB-LAN7430 EVALUATION BOARD USER'S GUIDE Chapter 2. Board Details and Configuration 2.1 BOARD DETAILS This section includes the following EVB-LAN7430 board details: * * * * Power Resets Clock Configuration 2.1.1 Power The board receives 3.3V supply through the PCIe interface. An internal 2.5V voltage regulator supplies power to the 2.5V tolerant supply pins such as the AVDDH_1/ AVDDH_2 and VPH pins, and the VDD12_SW_OUT pin supplies 1.2V to three VDD12CORE pins and VP and VPTX pins. An on-board power scheme can supply 3.3V to LAN7430 and other devices through the auxiliary pin of the PCIe interface. 2.1.2 Resets Jumper J2 is required to be populated if the reset function is required for the board. 2.1.3 Clock The evaluation board utilizes an external 25 MHz crystal oscillator. 2.1.4 Configuration Figure 2-1 describes the board features and configuration settings. 2019 Microchip Technology Inc. DS50002841A-page 11 EVB-LAN7430 Evaluation Board User's Guide FIGURE 2-1: EVB-LAN7430 TOP VIEW WITH CALLOUTS Reset SMA Connectors for IEEE 1588-2008 GPIO JTAG Test Points (TAP) RJ-45 Connector EEPROM Enable Header LAN7430 PCIe Edge Connector Oscillator 2.1.4.1 JUMPER SETTINGS Table 2-1 describes the jumper settings. The default configuration is shown in bold. TABLE 2-1: JUMPERS Jumper Label J2 Reset J6 EEPROM En 2.1.4.2 Description Open Close Provides the hardware reset to the board (Default) Board per- Resets the board forms normal operation. Enables optional EEPROM EEPROM is disabled. Internal OTP is used to configure LAN7430. (Default) EEPROM is enabled. HEADERS AND CONNECTORS Table 2-2 describes the functions of the headers on the board. TABLE 2-2: HEADERS AND CONNECTORS Header Description J1 8P8C (RJ-45) connector J3 GPIO1, GPIO2, GPIO 3, GPIO4 General purpose input/output (I/O) J4 PPS IEEE 1588 Pulse Per Second (PPS) input J5 Input Edge clock Capture IEEE 1588 Input Edge Clock Capture TDI/TDO/TMS/TCK Signals to enable fly-wiring of JTAG TAP from LAN7430 to the PCIe connector. When using the TAP, remove R13. JTAG TAP DS50002841A-page 12 Label Connects an Ethernet cable 2019 Microchip Technology Inc. EVB-LAN7430 EVALUATION BOARD USER'S GUIDE Chapter 3. Using the EVB-LAN7430 The EVB-LAN7430 board is connected to a PCIe slot of a PC. The LAN7430 device supports Windows 10 and Linux operating system. The drivers are provided on the LAN7430 device's product page for both operating systems. A `readme' file is also provided with the drivers, which describes the driver installation process in detail. Once the drivers are installed correctly for Windows 10, for example, the board can be detected in Device Manager as shown in Figure 3-1. FIGURE 3-1: LAN7430 DETECTED IN DEVICE MANAGER Once the PC detects the LAN7430 board correctly, the PC can then be connected to the Internet using an Ethernet cable to test the board. 2019 Microchip Technology Inc. DS50002841A-page 13 EVB-LAN7430 Evaluation Board User's Guide NOTES: DS50002841A-page 14 2019 Microchip Technology Inc. EVB-LAN7430 EVALUATION BOARD USER'S GUIDE Appendix A. EVB-LAN7430 Evaluation Board A.1 INTRODUCTION This appendix shows the EVB-LAN7430 Evaluation Board. FIGURE A-1: EVB-LAN7430 EVALUATION BOARD 2019 Microchip Technology Inc. DS50002841A-page 15 EVB-LAN7430 Evaluation Board User's Guide NOTES: DS50002841A-page 16 2019 Microchip Technology Inc. EVB-LAN7430 EVALUATION BOARD USER'S GUIDE Appendix B. Schematics B.1 INTRODUCTION This appendix shows the EVB-LAN7430 Evaluation Board schematics. 2019 Microchip Technology Inc. DS50002841A-page 17 EVB-LAN7430 EVALUATION BOARD SCHEMATICS RESET J2 RESET_N R12 DNP C37 R8 0R DNP 0R 0.1uF GREEN (LINK/ACT) PCIe_nPRSNT1 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 12V 12V 12V GND SMCLK SMDAT GND 3V3 nTRST 3V3AUX nWAKE W R13 R2 U1B RESETn TEST TEST PERST# 0R TCK1 TDI1 TDO1 TMS1 TP3 GND PCIe_RFCK_P PCIe_RFCK_N PCIE_CLK_P PCIE_CLK_M PCIeGND PCIE_TX_P PCIE_TX_M PCIeGND PCIE_RX_P PCIE_RX_M PCIeGND PCIe_TXC_P PCIe_TXC_N TXP TP7 TXN TP8 PCIe_nPERST A12 A13 A14 A15 A16 A17 A18 nCLKREQ GND PETp0 PETn0 GND nPRSNT2 GND JTAG TAP J1 DNP 10k R7 C5 RXP TP4 0.1uF C4 RXN TP5 0.1uF PCIe_TX_P PCIe_TX_N TP1 GND 0R GPIO0 2 3 TXRXA_P TXRXA_N C31 0.1uF 5 6 TXRXB_P TXRXB_N C33 0.1uF 7 8 TXRXC_P TXRXC_N C32 0.1uF 10 11 TXRXD_P TXRXD_N C30 0.1uF 37 GPIO1 0 0R R5 R1 200R 6.04k 1% LAN7430 GPIO3 36 GPIO2 330R TCK TMS EEPROM Enable JTAG TAP XO XI R3 35 J3 0R X_4 XI C38 220R 8 7 6 5 CS CLK DI DO 0R C10 0.1uF 1k 8 BIT EEPROM GPIO2 CLK_IN TP16 2 STBY# MODULAR RJ45 Optional GPIO1 4 3 2 1 GPIO0 GPIO1 GPIO2 GPIO3 Y1 DNP FB7 R9 Oscillator option (DNP) R16 DNP 0R X_1 1588 Testing. GPIO3 PPS TP17 0.1uF DNP 330R GREEN (Duplex/Collision) U2 93AA66A J6 R6 GPIO0 R17 R11 16 GC2 XO PCIe_nCLKREQ PCIe_nWAKE XI RESREF PCIe_RX_N PCIe_RX_P ISET ISET Note: Remove NC pads. 25MHz DNP 3 VDD TRD1+ TRCT1 TRD1TRD2+ TRCT2 TRD2TRD3+ TRCT3 TRD3TRD4+ TRCT4 TRD4- TDO R4 RESREF 330R TDI CLKREQ# WAKE# P1 PCIe x1 PCB Edge (fingers) R10 14 GC1 38 DNP J4 GPIO2 GND R14 0R DNP Crystal(default) Y1 XI 1 X_1 25Mhz C34 15pF 15pF DNP R18 X_4 R19 XO Input Edge CLK Capture J5 DNP 0R C35 VDD_SW_IN 0R 3V3 TP9 TP11 GND C28 C20 4.7uF 0.1uF 0.1uF REG_IN SW_IN 2019 Microchip Technology Inc. C27 Power Power C25 C23 C22 C15 C16 1uF 0.1uF 0.1uF 0.1uF 0.1uF VDD_OTP D1 14 C12 Power C14 0.1uF 220R SW_OUT C7 C6 C8 10uF 10uF 0.1uF FB4 VDD12_SW_OUT TP13 R15 0R DNP C9 220R MH1 0.1uF DNP 1 TP12 GND FB5 220R 20 10uF D2 MBRA130 L1 13 31 40 45 4 9 FB2 Power SW_OUT_L 3.3uH VDDVARIO 3V3_PCIe - Power Supply 34 32 Crystal required for 1588-2008 PTP MBRA130 GPIO3 U1A Power Power Power C17 C24 C11 C13 C19 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF Power C18 C26 0.1uF 0.1uF VDD_REG_IN VSS(ePAD) 27 23 FB1 FB3 220R 1 12 LAN7430 BKT_PCI_LP_Enet_1 2V5 TP10 220R FB6 220R C2 C3 C36 1uF 0.1uF 10uF DNP Microchip Technology, Inc. USB/Network Group - UNG www.Microchip.com EVB-LAN7430 LAN7430 Project Name: EVB-LAN7430 Designed with Altium.com Description: Page Title: Size: B Date: 1/14/2019 Designer: Parthiv PN: LAN7430 Pandya Sheet 2 of 2 Rev B EVB-LAN7430 Evaluation Board User's Guide DS50002841A-page 18 FIGURE B-1: EVB-LAN7430 EVALUATION BOARD USER'S GUIDE Appendix C. Bill of Materials C.1 INTRODUCTION This appendix includes the EVB-LAN7430 Bill of Materials (BOM). 2019 Microchip Technology Inc. DS50002841A-page 19 EVB-LAN7430 BILL OF MATERIALS Item Qty Reference Description Populated Manufacturer Manufacturer Part Number 1 2 C2, C25 CAP CER 1uF 35V 10% X5R SMD 0402 YES Murata Electronics North America GRM155R6YA105KE11D 2 15 C3, C8, C9, C11, C13, C15, C16, C17, C18, C19, C20, C22, C23, C24, C28 CAP CER 0.1uF 50V 10% X7R SMD 0402 YES TDK Corporation C1005X7R1H104K050BB 3 8 C4, C5, C10, C14, C30, C31, C32, C33 CAP CER 0.1uF 50V 10% X7R SMD 0402 YES TDK Corporation C1005X7R1H104K050BB 4 3 C6, C7, C12 CAP CER 10UF 25V 20% X5R SMD 0603 YES Murata Electronics North America GRM188R61E106MA73D 5 1 C26 CAP CER 0.1uF 16V 10% X7R SMD 0402 YES Murata GRM155R71C104KA88D 6 1 C27 CAP CER 4.7uF 6.3V 20% X5R SMD 0402 YES Murata GRM155R60J475ME47D 7 1 C35 CAP CER 15pF 50V 5% NP0 SMD 0402 YES Murata GRM1555C1H150JA01D 8 2 D1, D2 DIO SCTKY MBRA130LT3G 410mV 1A 30V SMD DO-214AC SMA YES ON Semiconductor MBRA130LT3G 9 6 FB1, FB2, FB3, FB4, FB5, FB6 FERRITE 500mA 220R SMD 0603 YES Murata BLM18AG221SN1D 10 1 FB7 FERRITE 220R @ 100MHz 2A SMD 0603 YES Murata Electronics North America BLM18EG221SN1D 11 1 J1 CON MODULAR JACK RJ45 10/100/1000 MAGNETICS 2xLEDs SHIELD TH R/A YES Amphenol Commercial Products RJMG2012211A0FR 12 1 J3 CON HDR-2.54 Male 1x4 Gold 5.84MH TH VERT YES Wurth Electronics Inc 61300411121 13 1 J6 CON HDR-2.54 Male 1x2 Gold 5.84MH TH VERT YES FCI 77311-118-02LF 14 1 L1 INDUCTOR 3.3UH 2.25A 20% SMD L3W2.5H1.5 YES TDK Corporation VLF302515MT-3R3M 15 1 MH1 Bracket, BKT_PCI_LP_Enet_1, GLOBE YES Keystone 16 1 R1 RES TKF 6.04k 1% 1/10W SMD 0603 YES Yageo 9T06031A6041FBHFT 2019 Microchip Technology Inc. 17 5 R2, R4, R6, R8, R13 RES TKF 0R 1/10W SMD 0603 YES Panasonic ERJ-3GSY0R00V 18 1 R3 RES TKF 200R 1% 1/10W SMD 0603 YES Panasonic ERJ-3EKF2000V 19 3 R5, R10, R11 RES TKF 330R 1% 1/10W SMD 0603 YES Panasonic ERJ-3EKF3300V 20 1 R9 RES TKF 1k 5% 1/10W SMD 0603 YES Panasonic ERJ-3GEYJ102V 21 1 R12 RES TKF 10k 1% 1/10W SMD 0603 YES Panasonic ERJ-3EKF1002V ERJ-2GE0R00X 22 2 R18, R19 RES TKF 0R SMD 0402 YES Panasonic 23 1 U1 MCHP INTERFACE PCIe-GIGe ETHERNET LAN7430 SQFN-48 YES Microchip Technology LAN7430/YXX 24 1 U2 MCHP MEMORY SERIAL EEPROM 4k Microwire 93AA66A-I/SN SOIC-8 YES Microchip 93AA66A-I/SN 25 1 C34 CAP CER 15pF 50V 5% NP0 SMD 0402 NO Murata GRM1555C1H150JA01D 26 1 C36 CAP CER 10UF 25V 20% X5R SMD 0603 NO Murata Electronics North America GRM188R61E106MA73D 27 1 C37 CAP CER 0.1uF 50V 10% X7R SMD 0402 NO TDK Corporation C1005X7R1H104K050BB EVB-LAN7430 Evaluation Board User's Guide DS50002841A-page 20 TABLE C-1: 2019 Microchip Technology Inc. TABLE C-1: EVB-LAN7430 BILL OF MATERIALS (CONTINUED) Item Qty Reference Description Populated Manufacturer Manufacturer Part Number 28 1 C38 CAP CER 0.1uF 50V 10% X7R SMD 0402 NO TDK Corporation 29 1 J2 CON HDR-2.54 Male 1x2 Gold 5.84MH TH VERT NO FCI 77311-118-02LF 30 2 J4, J5 CON RF Coaxial SMA Female TH R/A NO TE Connectivity AMP Connectors 5-1814400-1 31 1 R7 RES TKF 0R 1/10W SMD 0603 NO Panasonic ERJ-3GSY0R00V 32 2 R14, R15 RES TKF 0R 1/16W SMD 0402 NO Yageo RC0402JR-070RL 33 2 R16, R17 RES TKF 0R SMD 0402 NO Panasonic ERJ-2GE0R00X 34 1 Y1 MCHP CLOCK OSCILLATOR SINGLE 25MHZ DSC1001CI2-025.0000T CDFN-4 NO Microchip Technology DSC1001CI2-025.0000T 35 1 Y1 CRYSTAL 25MHz 10pF SMD ABM8G YES Abracon LLC ABM8G-25.000MHZ-4Y-T3 C1005X7R1H104K050BB Bill of Materials DS50002841A-page 21 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Australia - Sydney Tel: 61-2-9868-6733 India - Bangalore Tel: 91-80-3090-4444 China - Beijing Tel: 86-10-8569-7000 India - New Delhi Tel: 91-11-4160-8631 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 China - Chengdu Tel: 86-28-8665-5511 India - Pune Tel: 91-20-4121-0141 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 China - Chongqing Tel: 86-23-8980-9588 Japan - Osaka Tel: 81-6-6152-7160 Finland - Espoo Tel: 358-9-4520-820 China - Dongguan Tel: 86-769-8702-9880 Japan - Tokyo Tel: 81-3-6880- 3770 China - Guangzhou Tel: 86-20-8755-8029 Korea - Daegu Tel: 82-53-744-4301 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 China - Hangzhou Tel: 86-571-8792-8115 Korea - Seoul Tel: 82-2-554-7200 China - Hong Kong SAR Tel: 852-2943-5100 Malaysia - Kuala Lumpur Tel: 60-3-7651-7906 China - Nanjing Tel: 86-25-8473-2460 Malaysia - Penang Tel: 60-4-227-8870 China - Qingdao Tel: 86-532-8502-7355 Philippines - Manila Tel: 63-2-634-9065 China - Shanghai Tel: 86-21-3326-8000 Singapore Tel: 65-6334-8870 China - Shenyang Tel: 86-24-2334-2829 Taiwan - Hsin Chu Tel: 886-3-577-8366 China - Shenzhen Tel: 86-755-8864-2200 Taiwan - Kaohsiung Tel: 886-7-213-7830 Israel - Ra'anana Tel: 972-9-744-7705 China - Suzhou Tel: 86-186-6233-1526 Taiwan - Taipei Tel: 886-2-2508-8600 China - Wuhan Tel: 86-27-5980-5300 Thailand - Bangkok Tel: 66-2-694-1351 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 China - Xian Tel: 86-29-8833-7252 Vietnam - Ho Chi Minh Tel: 84-28-5448-2100 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Austin, TX Tel: 512-257-3370 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-4000 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Tel: 317-536-2380 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Tel: 951-273-7800 Raleigh, NC Tel: 919-844-7510 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Tel: 408-436-4270 Canada - Toronto Tel: 905-695-1980 Fax: 905-695-2078 DS50002841A-page 22 China - Xiamen Tel: 86-592-2388138 China - Zhuhai Tel: 86-756-3210040 Germany - Garching Tel: 49-8931-9700 Germany - Haan Tel: 49-2129-3766400 Germany - Heilbronn Tel: 49-7131-67-3636 Germany - Karlsruhe Tel: 49-721-625370 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Germany - Rosenheim Tel: 49-8031-354-560 Italy - Padova Tel: 39-049-7625286 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Norway - Trondheim Tel: 47-7288-4388 Poland - Warsaw Tel: 48-22-3325737 Romania - Bucharest Tel: 40-21-407-87-50 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden - Gothenberg Tel: 46-31-704-60-40 Sweden - Stockholm Tel: 46-8-5090-4654 UK - Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820 2019 Microchip Technology Inc. 08/15/18