ON Semiconductor SWITCHMODE Series NPN Silicon Power Transistors These devices are designed for high-voltage, high-speed power switching inductive circuits where fall time is critical. They are particularly suited for 115 and 220 V SWITCHMODE applications such as Switching Regulator's, Inverters, Motor Controls, Solenoid/Relay drivers and Deflection circuits. MJE13005 * *ON Semiconductor Preferred Device 4 AMPERE NPN SILICON POWER TRANSISTOR 400 VOLTS 75 WATTS SPECIFICATION FEATURES: * VCEO(sus) 400 V * Reverse Bias SOA with Inductive Loads @ TC = 100C * Inductive Switching Matrix 2 to 4 Amp, 25 and 100C * * 4 tc @ 3A, 100C is 180 ns (Typ) 700 V Blocking Capability SOA and Switching Applications Information. 1 2 STYLE 1: PIN 1. 2. 3. 4. BASE COLLECTOR EMITTER COLLECTOR 3 CASE 221A-09 TO-220AB IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII IIIIIIIIIIIIIIIII IIIIIII IIIIIIII IIII MAXIMUM RATINGS Rating Symbol Value Unit Collector-Emitter Voltage VCEO(sus) 400 Vdc Collector-Emitter Voltage VCEV 700 Vdc Emitter Base Voltage VEBO 9 Vdc Collector Current -- Continuous -- Peak (1) IC ICM 4 8 Adc Base Current -- Continuous -- Peak (1) IB IBM 2 4 Adc Emitter Current -- Continuous -- Peak (1) IE IEM 6 12 Adc Total Power Dissipation @ TA = 25C Derate above 25C PD 2 16 Watts mW/C Total Power Dissipation @ TC = 25C Derate above 25C PD 75 600 Watts mW/C TJ, Tstg -65 to +150 C Operating and Storage Junction Temperature Range THERMAL CHARACTERISTICS Symbol Max Unit Thermal Resistance, Junction to Ambient Characteristic RJA 62.5 C/W Thermal Resistance, Junction to Case RJC 1.67 C/W TL 275 C Maximum Lead Temperature for Soldering Purposes: 1/8 from Case for 5 Seconds (1) Pulse Test: Pulse Width = 5 ms, Duty Cycle 10%. Semiconductor Components Industries, LLC, 2002 April, 2002 - Rev. 6 1 Publication Order Number: MJE13005/D MJE13005 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIII IIIII IIII IIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIII IIII IIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIII IIII IIIIIIII IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIII IIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIII IIIIIIIIIIII IIIII IIII III IIII III IIIIIIII IIIIIIIIIIII IIIII IIII III IIII III IIIIIIII IIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIII IIIIIIIIIIII IIIII IIII III IIII III IIIIIIII IIIIIIIIIIII IIIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIII IIIIIIIIIIII IIIII IIII III IIII III IIIIIIII IIIIIIIIIIII IIIII IIII III IIII III IIIIIIII IIIIIIIIIIII IIIII IIII III IIII III ELECTRICAL CHARACTERISTICS (TC = 25C unless otherwise noted) Characteristic Symbol Min Typ Max Unit VCEO(sus) 400 -- -- Vdc -- -- -- -- 1 5 -- -- 1 *OFF CHARACTERISTICS Collector-Emitter Sustaining Voltage (IC = 10 mA, IB = 0) Collector Cutoff Current (VCEV = Rated Value, VBE(off) = 1.5 Vdc) (VCEV = Rated Value, VBE(off) = 1.5 Vdc, TC = 100C) ICEV Emitter Cutoff Current (VEB = 9 Vdc, IC = 0) IEBO mAdc mAdc SECOND BREAKDOWN Second Breakdown Collector Current with base forward biased Clamped Inductive SOA with Base Reverse Biased IS/b See Figure 11 RBSOA See Figure 12 *ON CHARACTERISTICS DC Current Gain (IC = 1 Adc, VCE = 5 Vdc) (IC = 2 Adc, VCE = 5 Vdc) hFE -- 10 8 -- -- 60 40 -- -- -- -- -- -- -- -- 0.5 0.6 1 1 -- -- -- -- -- -- 1.2 1.6 1.5 fT 4 -- -- MHz Cob -- 65 -- pF td -- 0.025 0.1 s tr -- 0.3 0.7 s ts -- 1.7 4 s tf -- 0.4 0.9 s tsv -- 0.9 4 s tc -- 0.32 0.9 s tfi -- 0.16 -- s Collector-Emitter Saturation Voltage (IC = 1 Adc, IB = 0.2 Adc) (IC = 2 Adc, IB = 0.5 Adc) (IC = 4 Adc, IB = 1 Adc) (IC = 2 Adc, IB = 0.5 Adc, TC = 100C) VCE(sat) Base-Emitter Saturation Voltage (IC = 1 Adc, IB = 0.2 Adc) (IC = 2 Adc, IB = 0.5 Adc) (IC = 2 Adc, IB = 0.5 Adc, TC = 100C) VBE(sat) Vdc Vdc DYNAMIC CHARACTERISTICS Current-Gain -- Bandwidth Product (IC = 500 mAdc, VCE = 10 Vdc, f = 1 MHz) Output Capacitance (VCB = 10 Vdc, IE = 0, f = 0.1 MHz) SWITCHING CHARACTERISTICS Resistive Load (Table 2) Delay Time Rise Time Storage Time (VCC = 125 Vdc, IC = 2 A, IB1 = IB2 = 0.4 0 4 A, A tp = 25 s, s Duty Cycle 1%) Fall Time Inductive Load, Clamped (Table 2, Figure 13) Voltage Storage Time Crossover Time Vd (IC = 2 A A, Vclamp = 300 Vdc, IB1 = 0.4 A, VBE(off) = 5 Vdc, TC = 100 100C) C) Fall Time *Pulse Test: Pulse Width = 300 s, Duty Cycle = 2%. http://onsemi.com 2 VCE , COLLECTOR-EMITTER VOLTAGE (VOLTS) MJE13005 100 hFE , DC CURRENT GAIN 70 TJ = 150C 50 25C 30 20 -55C 10 VCE = 2 V VCE = 5 V 7 5 0.04 0.06 0.1 0.4 0.6 0.2 1 IC, COLLECTOR CURRENT (AMP) 2 4 2 TJ = 25C 1.6 IC = 1 A VCE(sat) , COLLECTOR-EMITTER SATURATION VOLTAGE (VOLTS) VBE, BASE-EMITTER VOLTAGE (VOLTS) 0.9 TJ = -55C 25C 0.7 25C 0.5 150C 0.3 0.04 0.06 0.1 0.2 0.4 0.6 1 2 4 0.4 0 0.03 2 3 0.55 IC/IB = 4 0.45 TJ = -55C 0.35 25C 0.25 0.15 150C 0.05 0.04 0.06 0.1 0.2 0.4 0.6 1 2 4 2k C, CAPACITANCE (pF) IC, COLLECTOR CURRENT (A) 1 Figure 4. Collector-Emitter Saturation Voltage TJ = 150C 125C 100C 75C 50C 25C 0.1 -0.4 0.2 0.3 0.5 0.7 IB, BASE CURRENT (AMP) Figure 3. Base-Emitter Voltage 1k 1 0.1 IC, COLLECTOR CURRENT (AMP) VCE = 250 V 10 0.05 IC, COLLECTOR CURRENT (AMP) 10 k 100 4A Figure 2. Collector Saturation Region 1.3 VBE(sat) @ IC/IB = 4 VBE(on) @ VCE = 2 V 3A 0.8 Figure 1. DC Current Gain 1.1 2A 1.2 REVERSE 300 200 100 70 50 30 FORWARD -0.2 +0.2 +0.4 0 VBE, BASE-EMITTER VOLTAGE (VOLTS) Cib 1k 700 500 20 0.3 +0.6 Cob 0.5 10 30 1 3 5 50 VR, REVERSE VOLTAGE (VOLTS) Figure 6. Capacitance Figure 5. Collector Cutoff Region http://onsemi.com 3 100 300 MJE13005 ICPK Vclamp 90% Vclamp IC 90% IC trv tsv tfi tti tc VCE IB 10% Vclamp 90% IB1 10% ICPK 2% IC TIME Figure 7. Inductive Switching Measurements IIII III III III III III IIII IIII III III III III III IIII IIII III III III III III IIII IIII III III III III III IIII IIII III III III III III IIII IIII III III III III III IIII IIII III III III III III IIII IIII III III III III III IIII Table 1. Typical Inductive Switching Performance IC AMP TC C tsv ns trv ns tfi ns tti ns tc ns 2 25 100 600 900 70 110 100 240 80 130 180 320 3 25 100 650 950 60 100 140 330 60 100 200 350 4 25 100 550 850 70 110 160 350 100 160 220 390 NOTE: All Data recorded in the inductive Switching Circuit In Table 2. SWITCHING TIMES NOTE In resistive switching circuits, rise, fall, and storage times have been defined and apply to both current and voltage waveforms since they are in phase. However, for inductive loads which are common to SWITCHMODE power supplies and hammer drivers, current and voltage waveforms are not in phase. Therefore, separate measurements must be made on each waveform to determine the total switching time. For this reason, the following new terms have been defined. tsv = Voltage Storage Time, 90% IB1 to 10% Vclamp trv = Voltage Rise Time, 10-90% Vclamp tfi = Current Fall Time, 90-10% IC tti = Current Tail, 10-2% IC tc = Crossover Time, 10% Vclamp to 10% IC An enlarged portion of the inductive switching waveforms is shown in Figure 7 to aid in the visual identity of these terms. For the designer, there is minimal switching loss during storage time and the predominant switching power losses occur during the crossover interval and can be obtained using the standard equation from AN-222: PSWT = 1/2 VCCIC(tc)f In general, t rv + tfi tc. However, at lower test currents this relationship may not be valid. As is common with most switching transistors, resistive switching is specified at 25C and has become a benchmark for designers. However, for designers of high frequency converter circuits, the user oriented specifications which make this a "SWITCHMODE" transistor are the inductive switching speeds (tc and tsv) which are guaranteed at 100C. RESISTIVE SWITCHING PERFORMANCE 1 10 VCC = 125 V IC/IB = 5 TJ = 25C 0.5 0.2 t, TIME (s) t, TIME (s) tr 0.1 0.05 td @ VBE(off) = 5 V 0.01 0.04 2 1 0.5 0.3 0.02 VCC = 125 V IC/IB = 5 TJ = 25C ts 5 tf 0.2 0.1 0.2 0.4 1 2 0.1 0.04 4 0.1 0.2 0.5 1 IC, COLLECTOR CURRENT (AMP) IC, COLLECTOR CURRENT (AMP) Figure 8. Turn-On Time Figure 9. Turn-Off Time http://onsemi.com 4 2 4 MJE13005 Table 2. Test Conditions for Dynamic Performance RESISTIVE SWITCHING REVERSE BIAS SAFE OPERATING AREA AND INDUCTIVE SWITCHING +5 V 1N4933 33 TEST CIRCUITS 0.001 F PW 2N222 2 1k 68 L +125 V MR826* 1k T.U.T. 47 100 1/2 W NOTE PW and VCC Adjusted for Desired IC RB Adjusted for Desired IB1 5.1 k IB 2N2905 Coil Data: Ferroxcube Core #6656 Full Bobbin (~16 Turns) #16 Vclamp IC RB 1k +5 V 1N493 3 0.02 F 270 CIRCUIT VALUES MJE210 33 1N4933 5V DUTY CYCLE 10% tr, tf 10 ns VCC RB TEST WAVEFORMS IC(pk) 51 D1 VCE -4.0 V -VBE(off) VCC = 125 V RC = 62 D1 = 1N5820 or Equiv. RB = 22 VCC = 20 V Vclamp = 300 Vdc t1 VCE tf VCE or Vclamp r(t), TRANSIENT THERMAL RESISTANCE (NORMALIZED) TIME 1 0.7 0.5 -8 V Lcoil (ICpk) Vclamp tr, tf < 10 ns Duty Cycle = 1.0% RB and RC adjusted for desired IB and IC 0.1 0.1 0.02 0.01 SINGLE PULSE 0.02 0.05 0.1 P(pk) ZJC(t) = r(t) RJC RJC = 1.67C/W MAX D CURVES APPLY FOR POWER PULSE TRAIN SHOWN READ TIME AT t1 TJ(pk) - TC = P(pk) ZJC(t) 0.05 0.02 0.01 0.01 0 Test Equipment Scope-Tektronics 475 or Equivalent 0.2 0.2 0.03 t 25 s D = 0.5 0.3 0.07 0.05 Lcoil (ICpk) t1 VCC t2 t2 +10 V t1 ADJUSTED TO OBTAIN IC t SCOPE MJE200 GAP for 200 H/20 A Lcoil = 200 H tf CLAMPED tf UNCLAMPED t2 RC *SELECTED FOR 1 kV OUTPUT WAVEFORMS IC TUT 0.2 0.5 1 2 5 t, TIME (ms) 10 20 Figure 10. Typical Thermal Response [ZJC(t)] http://onsemi.com 5 t1 t2 DUTY CYCLE, D = t1/t2 50 100 200 500 1k MJE13005 SAFE OPERATING AREA INFORMATION The Safe Operating Area Figures 11 and 12 are specified ratings for these devices under the test conditions shown. 4 5 2 IC(pk) , COLLECTOR CURRENT (AMP) IC, COLLECTOR CURRENT (AMP) 10 500 s 5 ms dc 1 0.5 1 ms 0.2 0.1 0.05 0.02 0.01 MJE13005 5 7 10 20 30 50 70 100 200 300 VCE, COLLECTOR-EMITTER VOLTAGE (VOLTS) 3 2 VBE(off) = 9 V 1 MJE13005 0 500 400 TC 100C IB1 = 2.0 A 0 100 200 300 400 500 600 5V 3V 1.5 V 700 800 VCE, COLLECTOR-EMITTER CLAMP VOLTAGE (VOLTS) Figure 11. Forward Bias Safe Operating Area Figure 12. Reverse Bias Switching Safe Operating Area FORWARD BIAS REVERSE BIAS There are two limitations on the power handling ability of a transistor: average junction temperature and second breakdown. Safe operating area curves indicate IC - VCE limits of the transistor that must be observed for reliable operation; i.e., the transistor must not be subjected to greater dissipation than the curves indicate. The data of Figure 11 is based on TC = 25C; T J(pk) is variable depending on power level. Second breakdown pulse limits are valid for duty cycles to 10% but must be derated when TC 25C. Second breakdown limitations do not derate the same as thermal limitations. Allowable current at the voltages shown on Figure 11 may be found at any case temperature by using the appropriate curve on Figure 13. T J(pk) may be calculated from the data in Figure 10. At high case temperatures, thermal limitations will reduce the power that can be handled to values less than the limitations imposed by second breakdown. For inductive loads, high voltage and high current must be sustained simultaneously during turn-off, in most cases, with the base to emitter junction reverse biased. Under these conditions the collector voltage must be held to a safe level at or below a specific value of collector current. This can be accomplished by several means such as active clamping, RC snubbing, load line shaping, etc. The safe level for these devices is specified as Reverse Bias Safe Operating Area and represents the voltage-current conditions during reverse biased turn-off. This rating is verified under clamped conditions so that the device is never subjected to an avalanche mode. Figure 12 gives the complete RBSOA characteristics. POWER DERATING FACTOR 1 SECOND BREAKDOWN DERATING 0.8 0.6 THERMAL DERATING 0.4 0.2 0 20 40 60 80 100 120 140 TC, CASE TEMPERATURE (C) Figure 13. Forward Bias Power Derating http://onsemi.com 6 160 MJE13005 PACKAGE DIMENSIONS TO-220AB CASE 221A-09 ISSUE AA -T- B SEATING PLANE C F T S 4 A Q 1 2 3 U H K Z L R V J G D N STYLE 1: PIN 1. 2. 3. 4. BASE COLLECTOR EMITTER COLLECTOR http://onsemi.com 7 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. DIM A B C D F G H J K L N Q R S T U V Z INCHES MIN MAX 0.570 0.620 0.380 0.405 0.160 0.190 0.025 0.035 0.142 0.147 0.095 0.105 0.110 0.155 0.018 0.025 0.500 0.562 0.045 0.060 0.190 0.210 0.100 0.120 0.080 0.110 0.045 0.055 0.235 0.255 0.000 0.050 0.045 ----0.080 MILLIMETERS MIN MAX 14.48 15.75 9.66 10.28 4.07 4.82 0.64 0.88 3.61 3.73 2.42 2.66 2.80 3.93 0.46 0.64 12.70 14.27 1.15 1.52 4.83 5.33 2.54 3.04 2.04 2.79 1.15 1.39 5.97 6.47 0.00 1.27 1.15 ----2.04 MJE13005 SWITCHMODE is a trademark of Semiconductor Components Industries, LLC. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800-282-9855 Toll Free USA/Canada http://onsemi.com 8 MJE13005/D