MC74VHC4051, MC74VHC4052, MC74VHC4053 Analog Multiplexers / Demultiplexers High-Performance Silicon-Gate CMOS The MC74VHC4051, MC74VHC4052 and MC74VHC4053 utilize silicon-gate CMOS technology to achieve fast propagation delays, low ON resistances, and low OFF leakage currents. These analog multiplexers/demultiplexers control analog voltages that may vary across the complete power supply range (from VCC to VEE). The VHC4051, VHC4052 and VHC4053 are identical in pinout to the high-speed HC4051A, HC4052A and HC4053A, and the metal-gate MC14051B, MC14052B and MC14053B. The Channel-Select inputs determine which one of the Analog Inputs/Outputs is to be connected, by means of an analog switch, to the Common Output/Input. When the Enable pin is HIGH, all analog switches are turned off. The Channel-Select and Enable inputs are compatible with standard CMOS outputs; with pullup resistors they are compatible with LSTTL outputs. These devices have been designed so that the ON resistance (Ron) is more linear over input voltage than Ron of metal-gate CMOS analog switches. * Fast Switching and Propagation Speeds * Low Crosstalk Between Switches * Diode Protection on All Inputs/Outputs * Analog Power Supply Range (VCC - VEE) = 2.0 to 12.0 V * Digital (Control) Power Supply Range (VCC - GND) = 2.0 to 6.0 V * Improved Linearity and Lower ON Resistance Than Metal-Gate Counterparts * Low Noise * Chip Complexity: VHC4051 -- 184 FETs or 46 Equivalent Gates VHC4052 -- 168 FETs or 42 Equivalent Gates VHC4053 -- 156 FETs or 39 Equivalent Gates * These Devices are Pb-Free and are RoHS Compliant http://onsemi.com MARKING DIAGRAMS 16 9 VHC405xG AWLYYWW SOIC-16 D SUFFIX CASE 751B 1 8 16 9 VHC 405x ALYWG G TSSOP-16 DT SUFFIX CASE 948F 1 8 16 SOIC EIAJ-16 M SUFFIX CASE 966 9 VHC405x ALYWG 1 8 VHC405x = Specific Device Code (x = 1, 2 or 3) A = Assembly Location L, WL = Wafer Lot Y, YY = Year W, WW = Work Week G or G = Pb-Free Package (Note: Microdot may be in either location) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 14 of this data sheet. (c) Semiconductor Components Industries, LLC, 2011 May, 2011 - Rev. 6 1 Publication Order Number: MC74VHC4051/D MC74VHC4051, MC74VHC4052, MC74VHC4053 13 X0 14 X1 15 X2 ANALOG 12 MULTIPLEXER/ INPUTS/ X3 DEMULTIPLEXER OUTPUTS X4 1 5 X5 2 X6 4 X7 11 A CHANNEL 10 B SELECT 9 INPUTS C 6 ENABLE PIN 16 = VCC PIN 7 = VEE PIN 8 = GND 3 X COMMON OUTPUT/ INPUT MC74VHC4051 Single-Pole, 8-Position Plus Common Off 12 ANALOG INPUTS/OUTPUTS CHANNELSELECT INPUTS X0 14 X1 15 X2 11 X3 Y0 Y1 Y2 Y3 A B ENABLE 13 X SWITCH X COMMON OUTPUTS/INPUTS 1 5 2 3 Y SWITCH Y 4 10 9 PIN 16 = VCC PIN 7 = VEE PIN 8 = GND 6 MC74VHC4052 Double-Pole, 4-Position Plus Common Off 12 X0 13 X1 14 X SWITCH 2 ANALOG INPUTS/OUTPUTS Y0 1 Y1 15 Y SWITCH 5 Z0 3 Z1 4 Z SWITCH X Y COMMON OUTPUTS/INPUTS Z 11 A 10 B 9 C 6 ENABLE PIN 16 = VCC PIN 7 = VEE PIN 8 = GND CHANNELSELECT INPUTS NOTE: This device allows independent control of each switch. Channel-Select Input A controls the X-Switch, Input B controls the Y-Switch and Input C controls the Z-Switch MC74VHC4053 Triple Single-Pole, Double-Position Plus Common Off Figure 1. Logic Diagrams http://onsemi.com 2 MC74VHC4051, MC74VHC4052, MC74VHC4053 FUNCTION TABLE - MC74VHC4051 VCC X2 X1 X0 X3 A B C 16 15 14 13 12 11 10 9 1 2 3 4 5 X4 X6 X X7 X5 6 7 Enable VEE Control Inputs Enable C L L L L L L L L H L L L L H H H H X 8 GND Figure 2. Pinout: MC74VHC4051 (Top View) Select B A ON Channels X0 X1 X2 X3 X4 X5 X6 X7 NONE L H L H L H L H X L L H H L L H H X X = Don't Care VCC X2 X1 X X0 X3 A B 16 15 14 13 12 11 10 9 1 2 3 4 5 Y0 Y2 Y Y3 Y1 6 7 Enable VEE FUNCTION TABLE - MC74VHC4052 Control Inputs 8 GND Enable B L L L L H L L H H X Select A ON Channels L H L H X Y0 Y1 Y2 Y3 X0 X1 X2 X3 NONE X = Don't Care Figure 3. Pinout: MC74VHC4052 (Top View) FUNCTION TABLE - MC74VHC4053 VCC Y X X1 X0 A B C 16 15 14 13 12 11 10 9 1 2 3 4 5 Y1 Y0 Z1 Z Z0 6 7 Enable VEE Control Inputs 8 GND Figure 4. Pinout: MC74VHC4053 (Top View) Enable C L L L L L L L L H L L L L H H H H X X = Don't Care http://onsemi.com 3 Select B A L L H H L L H H X L H L H L H L H X ON Channels Z0 Z0 Z0 Z0 Z1 Z1 Z1 Z1 Y0 Y0 Y1 Y1 Y0 Y0 Y1 Y1 NONE X0 X1 X0 X1 X0 X1 X0 X1 MC74VHC4051, MC74VHC4052, MC74VHC4053 IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIII IIIII III IIIIIIIIIIIIIIIIIIIIIIIIII MAXIMUM RATINGS* Symbol Parameter Value Unit - 0.5 to + 7.0 - 0.5 to + 14.0 V Negative DC Supply Voltage (Referenced to GND) - 7.0 to + 5.0 V VIS Analog Input Voltage VEE - 0.5 to VCC + 0.5 V Vin Digital Input Voltage (Referenced to GND) - 0.5 to VCC + 0.5 V 25 mA 500 450 mW - 65 to + 150 _C VCC Positive DC Supply Voltage VEE I (Referenced to GND) (Referenced to VEE) DC Current, Into or Out of Any Pin PD Power Dissipation in Still Air Tstg Storage Temperature Range SOIC Package TSSOP Package TL Lead Temperature, 1 mm from Case for 10 Seconds 260 *Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. Derating -- SOIC Package: - 7 mW/_C from 65_ to 125_C TSSOP Package: - 6.1 mW/_C from 65_ to 125_C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, Vin and Vout should be constrained to the range GND v (Vin or Vout) v VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or V CC ). Unused outputs must be left open. _C IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIIIIIIIIIII III III II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII RECOMMENDED OPERATING CONDITIONS Symbol Parameter (Referenced to GND) (Referenced to VEE) Min Max Unit 2.0 2.0 6.0 12.0 V VCC Positive DC Supply Voltage VEE Negative DC Supply Voltage, Output (Referenced to GND) - 6.0 GND V VIS Analog Input Voltage VEE VCC V Vin Digital Input Voltage (Referenced to GND) GND VCC V VIO* Static or Dynamic Voltage Across Switch 1.2 V - 55 + 125 _C 0 0 0 0 1000 800 500 400 ns TA Operating Temperature Range, All Package Types tr, tf Input Rise/Fall Time (Channel Select or Enable Inputs) VCC = 2.0 V VCC = 3.0 V VCC = 4.5 V VCC = 6.0 V *For voltage drops across switch greater than 1.2V (switch on), excessive VCC current may be drawn; i.e., the current out of the switch may contain both VCC and switch input components. The reliability of the device will be unaffected unless the Maximum Ratings are exceeded. http://onsemi.com 4 MC74VHC4051, MC74VHC4052, MC74VHC4053 DC CHARACTERISTICS -- Digital Section (Voltages Referenced to GND) VEE = GND, Except Where Noted Symbol Parameter Condition Guaranteed Limit VCC V -55 to 25C 85C 125C Unit VIH Minimum High-Level Input Voltage, Channel-Select or Enable Inputs Ron = Per Spec 2.0 3.0 4.5 6.0 1.50 2.10 3.15 4.20 1.50 2.10 3.15 4.20 1.50 2.10 3.15 4.20 V VIL Maximum Low-Level Input Voltage, Channel-Select or Enable Inputs Ron = Per Spec 2.0 3.0 4.5 6.0 0.5 0.9 1.35 1.8 0.5 0.9 1.35 1.8 0.5 0.9 1.35 1.8 V Iin Maximum Input Leakage Current, Channel-Select or Enable Inputs Vin = VCC or GND, VEE = - 6.0 V 6.0 0.1 1.0 1.0 A ICC Maximum Quiescent Supply Current (per Package) Channel Select, Enable and VIS = VCC or GND; VEE = GND VEE = - 6.0 VIO = 0 V 6.0 6.0 1 4 10 40 40 80 A IIII II IIIIIIIIIIIII IIIIIIIIIIIIIIIII IIIIIIIIIII IIIIII IIIIIIIIIIIII IIIIIIIIII II IIII IIII IIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII DC ELECTRICAL CHARACTERISTICS Analog Section Guaranteed Limit Symbol Ron Parameter Maximum "ON" Resistance VCC V VEE V - 55 to 25_C v 85_C v 125_C Unit Vin = VIL or VIH VIS = VCC to VEE IS v 2.0 mA (Figures 5 through 11) 3.0 4.5 4.5 6.0 0.0 0.0 - 4.5 - 6.0 200 160 120 100 240 200 150 125 320 280 170 140 Vin = VIL or VIH VIS = VCC or VEE (Endpoints) IS v 2.0 mA (Figures 5 through11) 3.0 4.5 4.5 6.0 0.0 0.0 - 4.5 - 6.0 150 110 90 80 180 140 120 100 230 190 140 115 3.0 4.5 4.5 6.0 0.0 0.0 - 4.5 - 6.0 40 20 10 10 50 25 15 12 80 40 18 14 Test Conditions Ron Maximum Difference in "ON" Resistance Between Any Two Channels in the Same Package Vin = VIL or VIH VIS = 1/2 (VCC - VEE) IS v 2.0 mA Ioff Maximum Off-Channel Leakage Current, Any One Channel Vin = VIL or VIH; VIO = VCC - VEE; Switch Off (Figure 12) 6.0 - 6.0 0.1 0.5 1.0 Maximum Off-Channel VHC4051 Vin = VIL or VIH; Leakage Current, VHC4052 VIO = VCC - VEE; Common Channel VHC4053 Switch Off (Figure 13) 6.0 6.0 6.0 - 6.0 - 6.0 - 6.0 0.2 0.1 0.1 2.0 1.0 1.0 4.0 2.0 2.0 Maximum On-Channel VHC4051 Vin = VIL or VIH; Leakage Current, VHC4052 Switch-to-Switch = Channel-to-Channel VHC4053 VCC - VEE; (Figure 14) 6.0 6.0 6.0 - 6.0 - 6.0 - 6.0 0.2 0.1 0.1 2.0 1.0 1.0 4.0 2.0 2.0 Ion http://onsemi.com 5 A A MC74VHC4051, MC74VHC4052, MC74VHC4053 AC CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns) Guaranteed Limit VCC V -55 to 25C 85C 125C Unit Symbol Parameter tPLH, tPHL Maximum Propagation Delay, Channel-Select to Analog Output (Figures 18, 19) 2.0 3.0 4.5 6.0 270 90 59 45 320 110 79 65 350 125 85 75 ns tPLH, tPHL Maximum Propagation Delay, Analog Input to Analog Output (Figures 20, 21) 2.0 3.0 4.5 6.0 40 25 12 10 60 30 15 13 70 32 18 15 ns tPLZ, tPHZ Maximum Propagation Delay, Enable to Analog Output (Figures 22, 23) 2.0 3.0 4.5 6.0 160 70 48 39 200 95 63 55 220 110 76 63 ns tPZL, tPZH Maximum Propagation Delay, Enable to Analog Output (Figures 22, 23) 2.0 3.0 4.5 6.0 245 115 49 39 315 145 69 58 345 155 83 67 ns Cin Maximum Input Capacitance, Channel-Select or Enable Inputs 10 10 10 pF CI/O Maximum Capacitance Analog I/O 35 35 35 pF Common O/I: VHC4051 VHC4052 VHC4053 130 80 50 130 80 50 130 80 50 Feedthrough 1.0 1.0 1.0 (All Switches Off) Typical @ 25C, VCC = 5.0 V, VEE = 0 V CPD Power Dissipation Capacitance (Figure 25)* VHC4051 VHC4052 VHC4053 * Used to determine the no-load dynamic power consumption: P D = CPD VCC 2 f + ICC VCC . http://onsemi.com 6 45 80 45 pF MC74VHC4051, MC74VHC4052, MC74VHC4053 ADDITIONAL APPLICATION CHARACTERISTICS (GND = 0 V) VCC V Symbol Parameter Condition BW Maximum On-Channel Bandwidth or Minimum Frequency Response (Figure 15) fin = 1MHz Sine Wave; Adjust fin Voltage to Obtain 0dBm at VOS; Increase fin Frequency Until dB Meter Reads -3dB; RL = 50, CL = 10pF Off-Channel Feedthrough Isolation (Figure 16) -- -- Feedthrough Noise. Channel-Select Input to Common I/O (Figure 17) -- Crosstalk Between Any Two Switches (Figure 24) (Test does not apply to VHC4051) THD 25C Unit `51 `52 `53 80 80 80 95 95 95 120 120 120 2.25 4.50 6.00 -2.25 -4.50 -6.00 fin = Sine Wave; Adjust fin Voltage to Obtain 0dBm at VIS fin = 10kHz, RL = 600, CL = 50pF 2.25 4.50 6.00 -2.25 -4.50 -6.00 -50 -50 -50 fin = 1.0MHz, RL = 50, CL = 10pF 2.25 4.50 6.00 -2.25 -4.50 -6.00 -40 -40 -40 Vin 1MHz Square Wave (tr = tf = 6ns); Adjust RL at Setup so that IS = 0A; Enable = GND RL = 600, CL = 50pF 2.25 4.50 6.00 -2.25 -4.50 -6.00 25 105 135 RL = 10k, CL = 10pF 2.25 4.50 6.00 -2.25 -4.50 -6.00 35 145 190 fin = Sine Wave; Adjust fin Voltage to Obtain 0dBm at VIS fin = 10kHz, RL = 600, CL = 50pF 2.25 4.50 6.00 -2.25 -4.50 -6.00 -50 -50 -50 fin = 1.0MHz, RL = 50, CL = 10pF 2.25 4.50 6.00 -2.25 -4.50 -6.00 -60 -60 -60 fin = 1kHz, RL = 10k, CL = 50pF THD = THDmeasured - THDsource VIS = 4.0VPP sine wave VIS = 8.0VPP sine wave VIS = 11.0VPP sine wave *Limits not tested. Determined by design and verified by qualification. MHz dB mVPP dB Total Harmonic Distortion (Figure 26) % 2.25 4.50 6.00 -2.25 -4.50 -6.00 0.10 0.08 0.05 180 300 160 250 Ron , ON RESISTANCE (OHMS) Ron , ON RESISTANCE (OHMS) Limit* VEE V 200 125C 150 25C -55C 100 50 140 120 125C 100 80 25C 60 -55C 40 20 0 0 0.25 0.5 0.75 1.0 1.25 1.5 1.75 2.0 0 2.25 0 VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE 0.25 0.5 0.75 1.0 1.25 1.5 1.75 2.0 2.25 2.5 2.75 3.0 VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE Figure 5. Typical On Resistance, VCC - VEE = 2.0 V Figure 6. Typical On Resistance, VCC - VEE = 3.0 V http://onsemi.com 7 120 105 100 90 80 Ron , ON RESISTANCE (OHMS) Ron , ON RESISTANCE (OHMS) MC74VHC4051, MC74VHC4052, MC74VHC4053 125C 60 25C 40 -55C 20 0 75 125C 60 25C 45 -55C 30 15 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 0 4.5 0 0.5 Figure 7. Typical On Resistance, VCC - VEE = 4.5 V 3.0 3.5 4.0 4.5 5.0 5.5 6.0 60 70 60 50 125C 40 30 25C 20 -55C 50 Ron , ON RESISTANCE (OHMS) Ron , ON RESISTANCE (OHMS) 2.0 2.5 Figure 8. Typical On Resistance, VCC - VEE = 6.0 V 80 125C 40 25C 30 -55C 20 10 10 0 -4.5 1.0 1.5 VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE -3.5 -2.5 -1.5 -0.5 0.5 1.5 2.5 3.5 0 -6.0 -5.0 -4.0 -3.0 -2.0 -1.0 4.5 VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE 2.0 3.0 4.0 5.0 6.0 Figure 10. Typical On Resistance, VCC - VEE = 12.0 V PLOTTER - 1.0 VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE Figure 9. Typical On Resistance, VCC - VEE = 9.0 V PROGRAMMABLE POWER SUPPLY 0 MINI COMPUTER DC ANALYZER + VCC DEVICE UNDER TEST ANALOG IN COMMON OUT VEE GND Figure 11. On Resistance Test Set-Up http://onsemi.com 8 MC74VHC4051, MC74VHC4052, MC74VHC4053 VCC VCC VCC 16 VEE ANALOG I/O OFF A VCC VIH OFF VCC COMMON O/I OFF NC OFF VIH 6 7 8 VEE COMMON O/I 6 7 8 VEE Figure 12. Maximum Off Channel Leakage Current, Any One Channel, Test Set-Up Figure 13. Maximum Off Channel Leakage Current, Common Channel, Test Set-Up VCC VCC VCC 16 A VEE fin COMMON O/I OFF VOS 16 0.1F ON VCC VCC 16 VEE dB METER ON N/C RL CL* ANALOG I/O VIL 6 7 8 6 7 8 VEE VEE Figure 14. Maximum On Channel Leakage Current, Channel to Channel, Test Set-Up VCC VIS fin VCC dB METER OFF RL Figure 15. Maximum On Channel Bandwidth, Test Set-Up VOS 16 0.1F *Includes all probe and jig capacitance CL* 16 RL ON/OFF COMMON O/I ANALOG I/O RL OFF/ON RL RL 6 7 8 VEE VIL or VIH VCC GND CHANNEL SELECT Vin 1 MHz tr = tf = 6 ns *Includes all probe and jig capacitance 6 7 8 VEE TEST POINT CL* VCC 11 CHANNEL SELECT *Includes all probe and jig capacitance Figure 16. Off Channel Feedthrough Isolation, Test Set-Up Figure 17. Feedthrough Noise, Channel Select to Common Out, Test Set-Up http://onsemi.com 9 MC74VHC4051, MC74VHC4052, MC74VHC4053 VCC VCC 16 VCC CHANNEL SELECT ON/OFF 50% COMMON O/I ANALOG I/O OFF/ON GND tPLH TEST POINT CL* tPHL ANALOG OUT 6 7 8 50% CHANNEL SELECT *Includes all probe and jig capacitance Figure 18. Propagation Delays, Channel Select to Analog Out Figure 19. Propagation Delay, Test Set-Up Channel Select to Analog Out VCC 16 VCC ANALOG IN COMMON O/I ANALOG I/O ON 50% TEST POINT CL* GND tPHL tPLH ANALOG OUT 6 7 8 50% *Includes all probe and jig capacitance Figure 20. Propagation Delays, Analog In to Analog Out tf tr tPZL POSITION 1 WHEN TESTING tPHZ AND tPZH POSITION 2 WHEN TESTING tPLZ AND tPZL 2 GND tPLZ HIGH IMPEDANCE 10% VCC VCC 16 1 TEST POINT ON/OFF CL* VOL tPHZ ENABLE VOH 90% 1k ANALOG I/O 2 50% tPZH ANALOG OUT 1 VCC 90% 50% 10% ENABLE ANALOG OUT Figure 21. Propagation Delay, Test Set-Up Analog In to Analog Out 50% 6 7 8 HIGH IMPEDANCE Figure 22. Propagation Delays, Enable to Analog Out Figure 23. Propagation Delay, Test Set-Up Enable to Analog Out http://onsemi.com 10 MC74VHC4051, MC74VHC4052, MC74VHC4053 VCC VIS A VCC 16 RL fin 16 VOS ON/OFF ON COMMON O/I NC ANALOG I/O 0.1F OFF/ON OFF VEE RL RL CL* RL CL* 6 7 8 VEE VCC 6 7 8 11 CHANNEL SELECT *Includes all probe and jig capacitance Figure 24. Crosstalk Between Any Two Switches, Test Set-Up Figure 25. Power Dissipation Capacitance, Test Set-Up 0 VIS VCC 0.1F fin ON CL* -20 TO DISTORTION METER -30 -40 dB RL FUNDAMENTAL FREQUENCY -10 VOS 16 -50 DEVICE -60 6 7 8 VEE SOURCE -70 -80 *Includes all probe and jig capacitance -90 - 100 1.0 2.0 3.125 FREQUENCY (kHz) Figure 26. Total Harmonic Distortion, Test Set-Up Figure 27. Plot, Harmonic Distortion APPLICATIONS INFORMATION outputs to VCC or GND through a low value resistor helps minimize crosstalk and feedthrough noise that may be picked up by an unused switch. Although used here, balanced supplies are not a requirement. The only constraints on the power supplies are that: VCC - GND = 2 to 6 volts VEE - GND = 0 to -6 volts VCC - VEE = 2 to 12 volts and VEE GND When voltage transients above VCC and/or below VEE are anticipated on the analog channels, external Germanium or Schottky diodes (Dx) are recommended as shown in Figure 29. These diodes should be able to absorb the maximum anticipated current surges during clipping. The Channel Select and Enable control pins should be at VCC or GND logic levels. VCC being recognized as a logic high and GND being recognized as a logic low. In this example: VCC = +5V = logic high GND = 0V = logic low The maximum analog voltage swings are determined by the supply voltages VCC and VEE. The positive peak analog voltage should not exceed VCC. Similarly, the negative peak analog voltage should not go below VEE. In this example, the difference between VCC and VEE is ten volts. Therefore, using the configuration of Figure 28, a maximum analog signal of ten volts peak-to-peak can be controlled. Unused analog inputs/outputs may be left floating (i.e., not connected). However, tying unused analog inputs and http://onsemi.com 11 MC74VHC4051, MC74VHC4052, MC74VHC4053 VCC +5V 16 +5V ANALOG SIGNAL -5V ON 6 7 8 Dx +5V ANALOG SIGNAL VCC 16 Dx Dx VEE VEE 7 8 -5V VEE Figure 28. Application Example Figure 29. External Germanium or Schottky Clipping Diodes +5V +5V 16 +5V ANALOG SIGNAL VEE ON/OFF 6 7 8 VEE Dx ON/OFF -5V TO EXTERNAL CMOS CIRCUITRY 0 to 5V DIGITAL SIGNALS 11 10 9 VCC ANALOG SIGNAL +5V * R R 11 10 9 +5V +5V VEE VEE 16 ANALOG SIGNAL ON/OFF +5V ANALOG SIGNAL R VEE +5V 6 7 8 LSTTL/NMOS CIRCUITRY VEE * 2K R 10K a. Using Pull-Up Resistors 11 10 9 LSTTL/NMOS CIRCUITRY HCT BUFFER b. Using HCT Interface Figure 30. Interfacing LSTTL/NMOS to CMOS Inputs A 11 13 LEVEL SHIFTER 14 B 10 15 LEVEL SHIFTER 12 C 9 1 LEVEL SHIFTER 5 ENABLE 6 2 LEVEL SHIFTER 4 3 Figure 31. Function Diagram, VHC4051 http://onsemi.com 12 X0 X1 X2 X3 X4 X5 X6 X7 X MC74VHC4051, MC74VHC4052, MC74VHC4053 A 10 12 LEVEL SHIFTER 14 B 9 15 LEVEL SHIFTER 11 13 ENABLE 6 1 LEVEL SHIFTER 5 2 4 3 X0 X1 X2 X3 X Y0 Y1 Y2 Y3 Y Figure 33. Function Diagram, VHC4052 A 11 13 LEVEL SHIFTER 12 14 B 10 1 LEVEL SHIFTER 2 15 C 9 3 LEVEL SHIFTER 5 4 ENABLE 6 LEVEL SHIFTER Figure 32. Function Diagram, VHC4053 http://onsemi.com 13 X1 X0 X Y1 Y0 Y Z1 Z0 Z MC74VHC4051, MC74VHC4052, MC74VHC4053 ORDERING & SHIPPING INFORMATION Device Package Shipping SOIC-16 2500 Units / Tape & Reel TSSOP-16 2500 Units / Tape & Reel SOIC-16 2500 Units / Tape & Reel TSSOP-16 2500 Units / Tape & Reel SOIC-16 2500 Units / Tape & Reel MC74VHC4053DTR2G TSSOP-16 2500 Units / Tape & Reel MC74VHC4051MG SOEIAJ-16 50 Units / Rail MC74VHC4052MG SOEIAJ-16 50 Units / Rail MC74VHC4052MELG SOEIAJ-16 2000 Units / Reel MC74VHC4053MG SOEIAJ-16 50 Units / Rail MC74VHC4051DR2G MC74VHC4051DTR2G MC74VHC4052DR2G MC74VHC4052DTR2G MC74VHC4053DR2G http://onsemi.com 14 MC74VHC4051, MC74VHC4052, MC74VHC4053 PACKAGE DIMENSIONS SOIC-16 CASE 751B-05 ISSUE K -A- 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 9 -B- 1 P 8 PL 0.25 (0.010) 8 B M S G R K F X 45 _ C -T- SEATING PLANE J M D 16 PL 0.25 (0.010) M T B S A S SOLDERING FOOTPRINT 8X 6.40 16X 1 1.12 16 16X 0.58 1.27 PITCH 8 9 DIMENSIONS: MILLIMETERS http://onsemi.com 15 DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019 MC74VHC4051, MC74VHC4052, MC74VHC4053 PACKAGE DIMENSIONS TSSOP-16 CASE 948F-01 ISSUE B 16X K REF 0.10 (0.004) 0.15 (0.006) T U T U M S V S K S K1 2X L/2 16 9 B -U- L SECTION N-N J PIN 1 IDENT. N 8 1 EEE CCC CCC EEE J1 0.25 (0.010) M 0.15 (0.006) T U S A -V- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. N F DETAIL E -W- C 0.10 (0.004) -T- SEATING PLANE D H G DETAIL E DIM A B C D F G H J J1 K K1 L M SOLDERING FOOTPRINT 7.06 1 0.65 PITCH 16X 0.36 16X 1.26 DIMENSIONS: MILLIMETERS http://onsemi.com 16 MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 --- 1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.18 0.28 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.193 0.200 0.169 0.177 --- 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.007 0.011 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ MC74VHC4051, MC74VHC4052, MC74VHC4053 PACKAGE DIMENSIONS SOEIAJ-16 CASE 966-01 ISSUE A 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). LE 9 Q1 E HE 1 M_ L 8 Z DETAIL P D e VIEW P A A1 b 0.13 (0.005) c M 0.10 (0.004) DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --2.05 0.05 0.20 0.35 0.50 0.10 0.20 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 _ 0_ 0.70 0.90 --0.78 INCHES MIN MAX --0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 _ 0_ 0.028 0.035 --0.031 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 17 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC74VHC4051/D