To our custo mers,
Old Company Name in Catalogs and Other Documents
On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology
Corporation, and Renesas Electronics Corpor ation took over all the business of both
companies. Therefore, althoug h the old com pany name remains in this docum ent, it is a valid
Renesas Electronics document. W e appreciate your understanding.
Renesas Electronics website: http://www.renesas.com
April 1st, 2010
Renesas Electronics Corporation
Issued by: Renesas Electronics Corporation (http://www.renesas.com)
Send any inquiries to http://www.renesas.com/inquiry.
Notice
1. All information included in this document is current as of the date this document is issued. Such information, however, is
subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please
confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to
additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website.
2. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights
of third parties by or arising from the use of Renesas Electronics products or technical information described in this document.
No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights
of Renesas Electronics or others.
3. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part.
4. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of
semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software,
and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by
you or third parties arising from the use of these circuits, software, or information.
5. When exporting the products or technology described in this document, you should comply with the applicable export control
laws and regulations and follow the procedures required by such laws and regulations. You should not use Renesas
Electronics products or the technology described in this document for any purpose relating to military applications or use by
the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and
technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited
under any applicable domestic or foreign laws or regulations.
6. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics
does not warrant that such information is error free. Ren esas E lectronics assumes no liability whatsoever for any da mages
incurred by you resulting from errors in or omissions from the information included herein.
7. Renesas Electronics products are classified acco rding to the following three quality grades: “Standard”, “High Quality”, and
“Specific”. The recommended applications for each Renesas Electronics product depends on the product’s quality grade, as
indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular
application. You may not use any Renesas Electronics product for any application categorized as “Specific” without the prior
written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for
which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way
liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an
application categorized as “Specific” or for which the product is not intended where you have failed to obtain the prior written
consent of Renesas Electronics. The quality grade of each Renesas Electronics product is “Standard” unless otherwise
expressly specified in a Renesas Electronics data sheets or data books, et c.
“Standard”: Computers; office equipment; communications equipment; test and measurement equipment; audio and visual
equipment; home electro nic app liances; machine tool s; p ersonal electron ic equipment; and indu strial robots .
“High Quality”: Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-
crime systems; safety equipment; and medical equipment not specifically designed for life support.
“Specific”: Aircraft; aerospace equ i pment; submersible repeaters; nu clear reactor control systems; medical equipment or
systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare
intervention (e.g. exci sion, et c.), and any other applications or purposes that pose a direct threat to human life.
8. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics,
especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation
characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or
damages arising out of the use of Renesas Electronics products beyond such specified ranges.
9. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have
specific chara cterist ics such as the o ccurren ce of failure at a certai n rate an d malfunct ion s under certai n u se cond itions. Further,
Renesas Electronics pr oducts are not subject to radiation resi stance design. Please be sure to implement safety measures to
guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a
Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire
control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because
the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system
manufactured by you.
10. Please contact a Renesas Electronics sales office for det ails as to environmental matters such as the environmental
compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable
laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS
Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with
applicable laws and regulations.
11. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas
Electronics.
12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this
document or Renesas Electronics products, or if you have any other inquiries.
(Note 1) “Renesas Electronics” as us ed in this document means Renesas Electronics Corporation and also includes its majo ri ty-
owned subsidiaries.
(Note 2) “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics.
Rev.2.00, Jul.16.2004, page 1 of 14
HD26LS32
Quadruple Differential Line Receivers With 3 State Outputs
REJ03D0295–0200Z
(Previous ADE-205-577 (Z))
Rev.2.00
Jul.16.2004
Description
The HD26LS32 features quadruple line receivers designed to meet the specs of EIA standard RS-422A and RS-423.
This device operates from a single 5 V power supply. The enable function is common to all four receivers and offers a
choice of active high or active low input. Fail safe design ensures that if the inputs are open, the outputs will always be
high.
Features
Ordering Infor mation
Part Name Package Type Package Code Package
Abbreviation Taping Abbreviation
(Quantity)
HD26LS32P DILP-16 pin (JEITA) DP-16E, -16FV P
HD26LS32FPEL SOP-16 pin (JEITA) FP-16DAV FP EL (2,000 pcs/reel)
Note: Please consults the sales office for the above package availability.
Logic Diagram
1Y
2Y
3Y
4Y
1A
1B
2A
2B
3A
3B
4A
4B
Enable G
Enable G
HD26LS32
Rev.2.00, Jul.16.2004, page 2 of 14
Pin Arrangement
(Top view)
1
2
3
4
5
6
7
1B
GND
1A
1Y
2Y
8
Enable G
2A
2B
13
14
15
10
11
12
9
16 VCC
4B
4A
4Y
Enable G
3Y
3A
3B
Function Table
Differential Input Enable Output
A – B G G
GG
GY
VID V TH HXH
XLH
VTL < VID < VTH HX?
XL?
VID V TL HXL
XLL
XLHZ
H : High level
L : Low level
X : Immaterial
? : Irrelevant
Z : High impedance
HD26LS32
Rev.2.00, Jul.16.2004, page 3 of 14
Absolute Maximum Ratings
Item Symbol Ratings Unit
Supply Voltage VCC*17.0 V
In Phase Input Voltage VIC ±25 V
Differential Input Voltage VID*2±25 V
Enable Input Voltage VIN 7V
Output Sink Current Iout 50 mA
Continuous Total Dissipation PT1W
Operating Temperature Range Topr 0 to +70 °C
Storage Temperature Range Tstg –65 to 150 °C
Notes: 1. All voltage values except for differential input voltage are with respect to network ground terminal.
2. Differential input voltage is measured at the noninverting input with respect to the corresponding inverting
onput.
3. The absolute maximum ratings are values which must not individually be exceeded, and furthermore, no two
of which may be realized at the same time.
Recommended Operating Conditions
Item Symbol Min Typ Max Unit
Supply Voltage VCC 4.75 5.00 5.25 V
In Phase Input Voltage VIC ——±7.0V
Output Current IOH –440 µA
IOL ——8 mA
Operating Temperature Topr 0 70 °C
HD26LS32
Rev.2.00, Jul.16.2004, page 4 of 14
Electrical Characteristics (Ta = 0 to +70°C)
Item Symbol Min Typ*1Max Unit Conditions
Differential Input High
Threshold Voltage
VTH ——0.2VV
IC = –7 to +7 V VOH = 2.7 V, IOH = –440 µA
Differential Input Low VTL –0.2 VOL = 0.4 V, IOL = 4 mA
Threshold Voltage –0.2 VOL = 0.45 V, IOL = 8 mA
Input Hysteresis*2VTH – VTL —30—mV
Enable Input Voltage VIH 2.0——V
VIL ——0.8
Enable Input Clamp
Voltage
VIK ——1.5 V
CC = 4.75 V, IIN = –18 mA
Output Voltage VOH 2.7 VCC = 4.75 V VID = 1 V, IOH = –440 µA
VOL ——0.4 V
IL (G) = 0.8 V VID = –1 V, IOL = 4 mA
0.45 VID = –1 V, IOL = 8 mA
Off State (High IOZ ——20µAV
CC = 5.25 V VO = 2.4 V
Impedance) Output
Current
–20 VO = 0.4 V
Line Input Current II
2.3
2.8
mA VI = 15 V, Other Inputs10 to +15 V
VI = –15 V, Other Inputs –15 to +10 V
Enable Input Current II (EN) 100 µA VI = 5.5 V
IIH ——20 V
I = 2.7 V
IIL –0.36 mA VI = 0.4 V
Input Resistance ri 6 9.8 kVIC = –15 to +15 V (Other Inputs AC GND)
Short Circuit Output
Current
IOS*3–15 –85 mA VCC = 5.25 V
Supply Current ICC —5270 V
CC = 5.25 V, VI = 0 V (All Outputs Disable)
Notes: 1. All typical values are at VCC = 5 V, Ta = 25°C,VIC = 0.
2. Hysteresis is the differential between the positive going input threshold voltage and the negative going input
threshold voltage.
3. Not more than one output should be shorted at a time.
Switching Characteristics (VCC = 5 V, Ta = 25°C)
TItem Symbol Min typ Max Unit Conditions
Propagation Delay Time tPLH, tPHL —1725nsC
L = 15 pF
Output Enable Time tZH, tZL —1522
Output Disable Time tHZ —1522 C
L = 5 pF
tLZ —2030
HD26LS32
Rev.2.00, Jul.16.2004, page 5 of 14
1. tPLH, tPHL
Test circuit
Pulse
Generator
Input
CL
Output
2 k
VCC
5 k
2 V
*1
*2
*3
Waveforms
Input A 0 V 0 V
0 V 0 V
tPLH
OH
VOL
V
1.3 V
2.5 V
–2.5 V
2.5 V
–2.5 V
tPHL
1.3 V
Input B
Output
HD26LS32
Rev.2.00, Jul.16.2004, page 6 of 14
2. tHZ, tZH
Test circuit
Input
Pulse
Generator
2.5 V
2 V
CL
Output 2 k
VCC
5 k
S1
*1
*2
*3
*4
Waveforms
Enable G 1.3 V 1.3 V
1.3 V 1.3 V
tZH
OH
V
1.3 V
3 V
0 V
3 V
0 V
tHZ
0.5 V
Output
Enable G
S1 : Open
0 V
1.4 V
S1 : Closed
HD26LS32
Rev.2.00, Jul.16.2004, page 7 of 14
3. tLZ, tZL
Test circuit
Input
Pulse
Generator
2.5 V
2 V
CL
Output 2 k
VCC
5 k
S2
Waveforms
Enable 1.3 V 1.3 V
1.3 V 1.3 V
tZL
OH
VOL
V
1.3 V
3 V
0 V
3 V
0 V
tLZ
0.5 V
Output
Enable G
S2 : Open S2 : Closed
1.4 V
Notes: 1. The pulse generator has the following characteristics :
PRR = 1 MHz, 50 % duty cycle, tr 15 ns, t f 6 ns, Zout = 50 .
2. CL includes probe and jig capacitance.
3. All diodes are 1S2074 (H)
4. To test G input,ground G input and apply an inverted input waveform.
HD26LS32
Rev.2.00, Jul.16.2004, page 8 of 14
HD26LS32 Line Receiver Applications
The HD26LS32 is a line receiver that meets the EIA RS-422A and RS-423A conditions. It has a high in-phase input
voltage range, both positive and negative, enabling highly reliable transmission to be performed even in noisy
environments.
Its main features are listed belo w.
Operates on a single 5 V power supply.
Three-state output
On-c hip fai l -sa fe cir cu i t
±7 V in-phase input voltage range
±200 mV input sensitivity
Minimum 6 k input r e sistance
A block diagram is shown in figure 1. The enable function is common to all four drivers, and either active-high or
active-low input can be selected .
When exchange is carried out using a party line system, it is better to keep the receiver input bias current constituting
the driver load small, as this allows more receivers to be connected.
Consequently, whereas an input resistance of 4 k or above is stipulated in RS-422A and RS-423A, the HD26LS32 has
been designed to allow a greater margin, with a minimum resistance of 6 k.
Figure 2 shows the input current characteristics of the HD26LS32.
The shaded areas in the graph indicate the input current allowable range stipulated in RS-422A and RS-423A.
HD26LS32 output is LS-TTL compatible and has a three-state function, enabling the output to be placed in the high-
impedance state, and so making the device suitable for bus line type applications.
With an in-phase input voltage range of ±7 V and a ±200 mV input sensitivity, the HD26LS32 can withstand use in
noisy envi ronments.
Also, since signals sent over a long-distance transmission line require a long transition time, it also takes a long time to
cross the receiver’s input threshold level.
Therefore, the input is provided with hysteresis of around 30 mV to prevent receiver output misoperation due to noise.
An example of input hysteresis is shown in figure 3.
The fail-safe function consists of resistances R connecting input A to VCC and input B to GND, as shown in figure 4.
This circuit provides for the receiver input section to be pulled up or down by a high resistance that prevents it from
becoming a driver load so that the output goes high in the event of a transmission line breakage or connector
detachment.
When the input pin is placed in the open state by the pull-up/pull-down resistance, the differential input voltage VID is
as follows:
VID: (VIA – VIB) 0.2 V
and t he output is fixed high.
However, if the receiver-side termination resistance remains connected despite a line breakage or connector detachment,
the output will be undetermined (figure 5).
HD26LS32
Rev.2.00, Jul.16.2004, page 9 of 14
1Y
2Y
3Y
4Y
1A
1B
2A
2B
3A
3B
4A
4B
Enable G
Enable G
Figure 1 HD26LS32 Block Diagram
5
4
3
2
1
0
1
2
3
4
5
25 20 15 10 5 0 5 10152025
Input Voltage Vin (V)
Input Current Iin (mA)
Ta = 25°C+3.25 mA
V
CC
= 0 V
V
CC
= 5.25 V
3.25 mA
10 V 3 V
+3 V +10 V
Figure 2 Input Voltage vs. Input Current Characteristics
5
4
3
2
1
0
–100 80 60 40 20 0 20 40 60 80 100
Differential Input Voltage VID (mV)
Output Voltage Vout (V)
VCC = 5 V, Ta = 25°C
VIC = 7 V
VIC = 0 V
VIC = +7 V
Input applied to pin A,
with pin B as reference
Figure 3 Differential Input Voltage vs. Output Voltage Characteristics
VCC
Y
R
R
A
B
Figure 4 Fail-Safe Function
HD26LS32
Rev.2.00, Jul.16.2004, page 10 of 14
This is because, since the termination resistance is normally matched to the transmission line characteristic impedance,
the value falls to several tens of hundreds of ohms, and the differential input pins are shorted by this termination
resistance. That is, the differential input voltage VID comes within the range
VID: –0.2 V < VIA – VIB < 0.2 V
and the outp ut beco mes undetermined.
To prevent this, resistance R1 is inserted in series with the transmission line as shown in figure 6, minimizing the effect
of the termination resistance. Resistance R2 is added to increase the current flowing between the termination resistance
and R1, enabling the value of R1 to be kept small.
Inserting resistances R1 and R2 in this way provides for the differential input volta ge VID to become 200 mV or higher,
but the following points must be noted.
Smallest possible R1 va lue
If this value is large, the receiver input sensitivit y will fall.
Largest possible R2 val ue
If this value is small, the load on the driver will be large.
Figure 7 shows experimental differential input voltages for variations in R1 and R2.
"H"
R
T
R
T
Undetermined
Figure 5 Examples of Transmission Line Disconnection
Receive
r
V
CC
R
2
R
2
R
1
R
1
R
T
Driver
Figure 6 Method of Enhancing Fail-Safe Function
0.6
0.5
0.4
0.3
0.2
0.1
0 5 10 15
R1 (k)
Differential Input Voltage VID (V)
R
2
= 30 k
50 k
100 k
300 k
R
2
=
VCC = 5 V
Ta = 25°C
VCC
R2
VID
R2
R1
R1
100
Figure 7 R1, R2 vs. Differential Input Voltage
HD26LS32
Rev.2.00, Jul.16.2004, page 11 of 14
RS-442A Interface Standard Applications
Figure 9 shows sample operation waveforms at various points with 1200 m and 12 m cable lengths.
1. Unidirection al Transmission (1 : 1 Configuratio n)
Receiver
Data
output
F
D
E
Driver B
C
AData
input R
T
Figure 8 1 : 1 Unidirectional Transmission
: 1200 m
: 100 kHz
Line
Frequency
: 5 µs/div
: 2 V/div
H
V
: 50%
: 100
Duty
R
T
: 12 m
: 10 MHz
Line
Frequency
: 50 ns/div
: 2 V/div
H
V
: 50%
: 100
Duty
R
T
A
GND
C
GND
B
GND
D
GND
F
GND
E
GND
A
GND
C
GND
B
GND
D
GND
F
GND
E
GND
Figure 9 Sample Transmission Waveforms
HD26LS32
Rev.2.00, Jul.16.2004, page 12 of 14
2. Unidirectional Transmission (1 : n Configuration)
Driver
Data
input R
T
Data
output
Data
output
Receiver
R
T
Data
output
Enable
Data
output
Figure 10 1 : n Unidirectional Transmission
With this connection method, n receivers are connected for one driver. In the RS-422A standard, ten receivers can be
connected simultaneously for one driver.
Conversely, it is also possible to connect one receiver for n drivers.
3. Bidirectional Tr ans mission
Driver Receiver
Data I/O
Enable
DriverReceiver
Data I/O
Enable
R
T
R
T
Figure 11 Bidirectional Transmission
When bidirectional data exchange is performed using a combination of the HD26LS31 and HD26LS32, since either
high or low output control is possible, using complementary enable inputs for the driver and receiver makes it easy to
configure the kind of combination illustrated in figure 11 .
Extending this combination makes it possible to exchange n-bit data simultaneously, and handle a party line system.
HD26LS32
Rev.2.00, Jul.16.2004, page 13 of 14
Package Dimensions
16
18
9
19.2
20.32 Max
6.3
7.4 Max
5.06 Max2.54 Min
0.51 Min
Package Code
JEDEC
JEITA
Mass
(reference value)
DP-16E
Conforms
Conforms
1.05 g
2.54 ± 0.25 0.48 ± 0.1
0.89 1.3 7.62
0.25+ 0.1
– 0.05
0˚ – 15˚
As of January, 2003
Unit: mm
16
18
9
19.2
20.32 Max
6.3
7.4 Max
5.06 Max2.54 Min
0.51 Min
Package Code
JEDEC
JEITA
Mass
(reference value)
DP-16FV
Conforms
Conforms
1.05 g
2.54 ± 0.25
*NI/Pd/AU Plating
*0.48 ± 0.08
0.89 1.3 7.62
*0.25
± 0.06
0˚ 15˚
Unit: mm
HD26LS32
Rev.2.00, Jul.16.2004, page 14 of 14
Package Code
JEDEC
JEITA
Mass
(reference value)
FP-16DAV
Conforms
0.24 g
*Ni/Pd/Au plating
*0.20 ± 0.05
*0.40 ± 0.06
0.12
0.15
M
2.20 Max
5.5
10.06
0.80 Max
16 9
18
10.5 Max
+ 0.20
0.30
7.80
0.70 ± 0.20
0˚ 8˚
0.10 ± 0.10
1.15
1.27
As of January, 2003
Unit: mm
Keep safety first in your circuit designs!
1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble
may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary
circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's
application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party.
2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data,
diagrams, charts, programs, algorithms, or circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of
publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is
therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product
information before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor
home page (http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to
evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes
no responsibility for any damage, liability or other loss resulting from the information contained herein.
5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life
is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a
product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater
use.
6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and
cannot be imported into a country other than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein.
Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
http://www.renesas.com
Renesas Technology America, Inc.
450 Holger Way, San Jose, CA 95134-1368, U.S.A
Tel: <1> (408) 382-7500 Fax: <1> (408) 382-7501
Renesas Technology Europe Limited.
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, United Kingdom
Tel: <44> (1628) 585 100, Fax: <44> (1628) 585 900
Renesas Technology Europe GmbH
Dornacher Str. 3, D-85622 Feldkirchen, Germany
Tel: <49> (89) 380 70 0, Fax: <49> (89) 929 30 11
Renesas Technology Hong Kong Ltd.
7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Hong Kong
Tel: <852> 2265-6688, Fax: <852> 2375-6836
Renesas Technology Taiwan Co., Ltd.
FL 10, #99, Fu-Hsing N. Rd., Taipei, Taiwan
Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999
Renesas Technology (Shanghai) Co., Ltd.
26/F., Ruijin Building, No.205 Maoming Road (S), Shanghai 200020, China
Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952
Renesas Technology Singapore Pte. Ltd.
1, Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001
RENESAS SALES OFFICES
© 2004. Renesas Technology Corp., All rights reserved. Printed in Japan.
Colophon .1.0