20013-01-16 GaAlAs Infrared Emitter in SMT Package GaAlAs-IR-Lumineszenzdiode in SMT-Gehause Version 1.0 (not for new design) SFH 426 Features: Besondere Merkmale: * * * * * * Replacement: SFH 4256 Very highly efficient GaAIAs-LED High reliability High pulse handling capability Suitable for surface mounting (SMT) Available on tape and reelAvailable on tape and reel * SFH 426 same package as SFH 325 * Good linearity at high currents * SFH 426 Gehausegleich mit SFH 325 * Gute Lineraitat bei hohen Stromen Applications Anwendungen * * * * * * * * * * * * * Miniature photointerrupters Industrial electronics For control and drive circuits Automotive technology Sensor technology Alarm and safety equipment IR free air transmission * * * * * * * Ersatz: SFH 4256 GaAIAs-LED mit sehr hohem Wirkungsgrad Hohe Zuverlassigkeit Hohe Impulsbelastbarkeit Oberflachenmontage geeignet Gegurtet lieferbar Miniaturlichtschranken Industrieelektronik Messen/Steuern/Regeln" Automobiltechnik Sensorik Alarm- und Sicherungssysteme IR-Freiraumubertragung Notes Hinweise Depending on the mode of operation, these devices emit highly concentrated non visible infrared light which can be hazardous to the human eye. Products which incorporate these devices have to follow the safety precautions given in IEC 60825-1 and IEC 62471. Je nach Betriebsart emittieren diese Bauteile hochkonzentrierte, nicht sichtbare Infrarot-Strahlung, die gefahrlich fur das menschliche Auge sein kann. Produkte, die diese Bauteile enthalten, mussen gema den Sicherheitsrichtlinien der IEC-Normen 60825-1 und 62471 behandelt werden. 20013-01-16 1 Version 1.0 (not for new design) SFH 426 Ordering Information Bestellinformation Type: Radiant Intensity Ordering Code Typ: Strahlstarke Bestellnummer IF= 100 mA, tp= 20 ms Ie [mW/sr] SFH 426 7 ( 4) Note: Measured at a solid angle of = 0.01 sr Anm:: Gemessen bei einem Raumwinkel = 0.01 sr Q65110A2512 Maximum Ratings (TA = 25 C) Grenzwerte Parameter Symbol Values Unit Bezeichnung Operation and storage temperature range Betriebs- und Lagertemperatur Symbol Werte Einheit Top; Tstg -40 ... 100 C Reverse voltage Sperrspannung VR 5 V Forward current Durchlassstrom IF 100 mA Surge current Stostrom (tp 10 s, D = 0) IFSM 2.5 A Total power dissipation Verlustleistung Ptot 180 mW Thermal resistance junction - ambient 1) page 13 Warmewiderstand Sperrschicht - Umgebung RthJA 450 K/W Thermal resistance junction - soldering point RthJS 200 K/W 1) Seite 13 2) page 13 Wamewiderstand Sperrschicht - Lotstelle 2) Seite 13 20013-01-16 2 Version 1.0 (not for new design) SFH 426 Characteristics (TA = 25 C) Kennwerte Parameter Symbol Values Unit Bezeichnung Symbol Werte Einheit Emission wavelength Zentrale Emissionswellenlange (IF = 100 mA, tp = 20 ms) peak 880 nm Spectral bandwidth at 50% of Imax Spektrale Bandbreite bei 50% von Imax (IF = 100 mA, tp = 20 ms) 80 nm Half angle Halbwinkel 60 Active chip area Aktive Chipflache A 0.09 mm2 Dimensions of active chip area Abmessungen der aktiven Chipflache LxW 0.3 x 0.3 mm x mm Rise and fall time of Ie ( 10% and 90% of Ie max) Schaltzeit von Ie ( 10% und 90% von Ie max) (IF = 100 mA, RL = 50 ) tr, tf 500 ns Capacitance Kapazitat (VR = 0 V, f = 1 MHz) C0 15 pF Forward voltage Durchlassspannung (IF = 100 mA, tp = 20 ms) VF 1.5 ( 1.8) V Forward voltage Durchlassspannung (IF = 1 A, tp = 100 s) VF 3 ( 3.8) V Reverse current Sperrstrom (VR = 5 V) IR 0.01 ( 1) A Total radiant flux Gesamtstrahlungsfluss (IF= 100 mA, tp= 20 ms) e 23 mW 20013-01-16 3 Version 1.0 (not for new design) SFH 426 Parameter Symbol Values Unit Bezeichnung Symbol Werte Einheit Temperature coefficient of Ie or e Temperaturkoeffizient von Ie bzw. e (IF = 100 mA, tp = 20 ms) TCI -0.5 Temperature coefficient of VF Temperaturkoeffizient von VF (IF = 100 mA, tp = 20 ms) TCV -2 mV / K Temperature coefficient of wavelength Temperaturkoeffizient der Wellenlange (IF = 100 mA, tp = 20 ms) TC 0.25 nm / K %/K Grouping (TA = 25 C) Gruppierung Group Min Radiant Intensity Typ Radiant Intensity Typ Radiant Intensity Gruppe Min Strahlstarke Typ Strahlstarke Typ Strahlstarke IF= 100 mA, tp= 20 ms IF= 100 mA, tp= 20 ms IF = 1 A, tp = 100 s SFH 426 Ie, min [mW / sr] Ie, typ [mW / sr] Ie, typ [mW / sr] 4 7 48 Note: measured at a solid angle of = 0.01 sr Anm.: gemessen bei einem Raumwinkel = 0.01 sr 20013-01-16 4 Version 1.0 (not for new design) SFH 426 Relative Spectral Emission Relative spektrale Emission Radiant Intensity Strahlstarke Ie / Ie(100 mA) = f(I F), single pulse, tp = 20 s, TA= 25C Irel = f(), TA = 25C OHR00877 100 OHR00878 10 2 rel % e e (100mA) 80 10 1 60 10 0 40 10 -1 20 0 750 20013-01-16 10 -2 800 850 900 10 -3 950 nm 1000 5 10 0 10 1 10 2 10 3 mA 10 4 F Version 1.0 (not for new design) SFH 426 Forward Current Durchlassstrom IF = f(VF), single pulse, tp = 100 s, TA= 25C Max. Permissible Forward Current Max. zulassiger Durchlassstrom IF, max = f(TA) OHR00883 120 OHR00881 10 1 F mA F A 100 10 0 80 R thjA = 450 K/W 10 -1 60 40 10 -2 20 0 0 20 40 60 80 10 -3 100 C 120 TA Permissible Pulse Handling Capability Zulassige Pulsbelastbarkeit IF = f(tp), TA = 25 C, duty cycle D = parameter OHR00886 10 4 mA F D = 0.005 0.01 0.02 0.05 10 3 0.1 0.2 0.5 10 2 DC D= tp T tp F T 10 1 -5 10 10 -4 10 -3 10 -2 10 -1 10 0 20013-01-16 10 1 s 10 2 tp 6 0 1 2 3 4 5 6 V VF 8 Version 1.0 (not for new design) SFH 426 Radiation Characteristics Abstrahlcharakteristik Irel = f() 40 30 20 10 0 50 OHL01660 1.0 0.8 0.6 60 0.4 70 0.2 80 0 90 100 1.0 0.8 0.6 0 0.4 20 40 60 80 Package Outline Mazeichnung 1.1 (0.043) Anode (1.4 (0.055)) (R1) (0.3 (0.012)) (2.9 (0.114)) Cathode marking 4.2 (0.165) 3.8 (0.150) C A GPLY6880 Dimensions in mm (inch). / Mae in mm (inch). 20013-01-16 (2.85 (0.112)) 0.9 (0.035) 3.8 (0.150) 3.4 (0.134) Cathode 2.54 (0.100) spacing 0.7 (0.028) 4.2 (0.165) 3.8 (0.150) 2.4 (0.094) 2.8 (0.110) (2.4 (0.094)) 7 100 120 Version 1.0 (not for new design) SFH 426 Package SIDELED, cathode marking: bevelled edge Gehause SIDELED, Kathodenkennzeichnung: abgesetzte Ecke Method of Taping Gurtung 4 (0.157) 4.25 (0.167) 8 (0.315) Dimensions in mm (inch). / Mae in mm (inch). 20013-01-16 8 12 (0.472) 1.75 (0.069) Cathode/Collector Marking 5.5 (0.217) 2 (0.079) 3.95 (0.156) 1.5 (0.059) OHAY2273 Version 1.0 (not for new design) SFH 426 Recommended Solder Pad Empfohlenes Lotpaddesign 3.0 (0.118) 3.7 (0.146) 1.2 (0.047) Padgeometrie fur verbesserte Warmeableitung Paddesign for improved heat dissipation Cu-Flache > 16 mm 2 Cu-area > 16 mm 2 Lotstopplack Solder resist OHLPY965 Dimensions in mm (inch). / Mae in mm (inch). 20013-01-16 9 Version 1.0 (not for new design) SFH 426 Reflow Soldering Profile Reflow-Lotprofil Preconditioning: JEDEC Level 2 acc. to JEDEC J-STD-020D.01 OHA04525 300 C T 250 Tp 245 C 240 C tP 217 C 200 tL 150 tS 100 50 25 C 0 0 50 100 150 200 s 300 250 t Profil-Charakteristik Profile Feature Symbol Symbol Pb-Free (SnAgCu) Assembly Minimum Ramp-up Rate to Preheat*) 25 C to 150 C Time tS TSmin to TSmax tS 60 Ramp-up Rate to Peak*) TSmax to TP Recommendation Maximum 2 3 100 120 2 3 Einheit Unit K/s s K/s Liquidus Temperature TL 217 Time above Liquidus temperature tL 80 100 s Peak Temperature TP 245 250 C Time within 5 C of the specified peak temperature TP - 5 K tP 20 30 s 3 4 K/s 10 Ramp-down Rate* TP to 100 C 480 Time 25 C to TP All temperatures refer to the center of the package, measured on the top of the component * slope calculation DT/Dt: Dt max. 5 s; fulfillment for the whole T-range 20013-01-16 C 10 s Version 1.0 (not for new design) SFH 426 TTW Soldering Wellenloten (TTW) IEC-61760-1 TTW / IEC-61760-1 TTW OHLY0598 300 C T 10 s 250 Normalkurve standard curve 235 C ... 260 C Grenzkurven limit curves 2. Welle 2. wave 200 1. Welle 1. wave 150 ca 200 K/s 2 K/s 5 K/s 100 C ... 130 C 100 2 K/s 50 Zwangskuhlung forced cooling 0 0 50 100 150 200 t 20013-01-16 11 s 250 Version 1.0 (not for new design) SFH 426 Disclaimer Disclaimer Attention please! The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. Due to technical requirements components may contain dangerous substances. For information on the types in question please contact our Sales Organization. If printed or downloaded, please find the latest version in the Internet. Packing Please use the recycling operators known to you. We can also help you - get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred. Components used in life-support devices or systems must be expressly authorized for such purpose! Critical components* may only be used in life-support devices** or systems with the express written approval of OSRAM OS. Bitte beachten! Lieferbedingungen und Anderungen im Design vorbehalten. Aufgrund technischer Anforderungen konnen die Bauteile Gefahrstoffe enthalten. Fur weitere Informationen zu gewunschten Bauteilen, wenden Sie sich bitte an unseren Vertrieb. Falls Sie dieses Datenblatt ausgedruckt oder heruntergeladen haben, finden Sie die aktuellste Version im Internet. Verpackung Benutzen Sie bitte die Ihnen bekannten Recyclingwege. Wenn diese nicht bekannt sein sollten, wenden Sie sich bitte an das nachstgelegene Vertriebsburo. Wir nehmen das Verpackungsmaterial zuruck, falls dies vereinbart wurde und das Material sortiert ist. Sie tragen die Transportkosten. Fur Verpackungsmaterial, das unsortiert an uns zuruckgeschickt wird oder das wir nicht annehmen mussen, stellen wir Ihnen die anfallenden Kosten in Rechnung. Bauteile, die in lebenserhaltenden Apparaten und Systemen eingesetzt werden, mussen fur diese Zwecke ausdrucklich zugelassen sein! Kritische Bauteile* durfen in lebenserhaltenden Apparaten und Systemen** nur dann eingesetzt werden, wenn ein schriftliches Einverstandnis von OSRAM OS vorliegt. *) A critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affect its safety or the effectiveness of that device or system. **) Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they fail, it is reasonable to assume that the health and the life of the user may be endangered. *) Ein kritisches Bauteil ist ein Bauteil, das in lebenserhaltenden Apparaten oder Systemen eingesetzt wird und dessen Defekt voraussichtlich zu einer Fehlfunktion dieses lebenserhaltenden Apparates oder Systems fuhren wird oder die Sicherheit oder Effektivitat dieses Apparates oder Systems beeintrachtigt. **) Lebenserhaltende Apparate oder Systeme sind fur (a) die Implantierung in den menschlichen Korper oder (b) fur die Lebenserhaltung bestimmt. Falls Sie versagen, kann davon ausgegangen werden, dass die Gesundheit und das Leben des Patienten in Gefahr ist. 20013-01-16 12 Version 1.0 (not for new design) SFH 426 Glossary Glossar 1) Thermal resistance: junction -ambient, mounted on PC-board (FR4), padsize 16 mm2 each 1) Warmewiderstand: Sperrschicht -Umgebung, bei Montage auf FR4 Platine, Padgroe je 16 mm2 2) Thermal resistance: junction mounted on metal block 2) Warmewiderstand: Sperrschicht Montage auf Metall-Block 20013-01-16 -soldering point, 13 -Lotstelle, bei Version 1.0 (not for new design) SFH 426 Published by OSRAM Opto Semiconductors GmbH Leibnizstrae 4, D-93055 Regensburg www.osram-os.com (c) All Rights Reserved. 20013-01-16 14