MC74HC573A Octal 3-State Noninverting Transparent Latch High-Performance Silicon-Gate CMOS The MC74HC573A is identical in pinout to the LS573. The devices are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LSTTL outputs. These latches appear transparent to data (i.e., the outputs change asynchronously) when Latch Enable is high. When Latch Enable goes low, data meeting the setup and hold time becomes latched. The HC573A is identical in function to the HC373A but has the data inputs on the opposite side of the package from the outputs to facilitate PC board layout. http://onsemi.com MARKING DIAGRAMS 20 1 Features * * * * * * * Output Drive Capability: 15 LSTTL Loads Outputs Directly Interface to CMOS, NMOS and TTL Operating Voltage Range: 2.0 to 6.0 V Low Input Current: 1.0 mA In Compliance with the JEDEC Standard No. 7.0 A Requirements Chip Complexity: 218 FETs or 54.5 Equivalent Gates These Devices are Pb-Free and are RoHS Compliant 20 PDIP-20 N SUFFIX CASE 738 MC74HC573AN AWLYYWWG 1 20 SOIC-20 DW SUFFIX CASE 751D 20 1 74HC573A AWLYYWWG 1 20 HC 573A ALYWG G TSSOP-20 DT SUFFIX CASE 948E 20 1 1 20 SOEIAJ-20 F SUFFIX CASE 967 1 20 1 A WL, L YY, Y WW, W G or G 74HC573A AWLYWWG = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package (Note: Microdot may be in either location) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet. (c) Semiconductor Components Industries, LLC, 2011 May, 2011 - Rev. 13 1 Publication Order Number: MC74HC573A/D MC74HC573A PIN ASSIGNMENT OUTPUT ENABLE D0 1 20 VCC 2 19 Q0 D1 3 18 Q1 D2 4 17 Q2 D3 5 16 Q3 D4 6 15 Q4 D5 7 14 Q5 D6 8 13 Q6 D7 9 12 10 11 Q7 LATCH ENABLE GND Value Units Internal Gate Count* Design Criteria 54.5 ea. Internal Gate Progation Delay 1.5 ns Internal Gate Power Dissipation 5.0 mW 0.0075 pJ Speed Power Product *Equivalent to a two-input NAND gate. LOGIC DIAGRAM D0 FUNCTION TABLE Inputs Output Enable Latch Enable L H L H L L H X X = Don't Care Z = High Impedance D1 Output D H L X X Q H L No Change Z D2 DATA INPUTS D3 D4 D5 D6 D7 LATCH ENABLE OUTPUT ENABLE 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 Q0 Q1 Q2 Q3 Q4 NONINVERTING OUTPUTS Q5 Q6 Q7 11 1 PIN 20 = VCC PIN 10 = GND ORDERING INFORMATION Package Shipping SOIC-20 (Pb-Free) 18 Units / Rail MC74HC573ADWG SOIC-20 WIDE (Pb-Free) 38 Units / Rail MC74HC573ADWR2G SOIC-20 WIDE (Pb-Free) 1000 Tape & Reel MC74HC573ADTG TSSOP-20* 75 Units / Rail MC74HC573ADTR2G TSSOP-20* 2500 Tape & Reel MC74HC573AFELG SOEIAJ-20 (Pb-Free) 2000 Tape & Reel Device MC74HC573ANG For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *This package is inherently Pb-Free. http://onsemi.com 2 MC74HC573A IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII MAXIMUM RATINGS Symbol Parameter Value Unit - 0.5 to + 7.0 V VCC DC Supply Voltage (Referenced to GND) Vin DC Input Voltage (Referenced to GND) - 0.5 to VCC + 0.5 V Vout DC Output Voltage (Referenced to GND) - 0.5 to VCC + 0.5 V Iin DC Input Current, per Pin 20 mA Iout DC Output Current, per Pin 35 mA ICC DC Supply Current, VCC and GND Pins 75 mA PD Power Dissipation in Still Air, 750 500 450 mW Tstg Storage Temperature - 65 to + 150 _C TL Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP, TSSOP or SOIC Package) Plastic DIP SOIC Package TSSOP Package _C 260 This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, Vin and Vout should be constrained to the range GND v (Vin or Vout) v VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Derating - Plastic DIP: - 10 mW/_C from 65_ to 125_C SOIC Package: - 7 mW/_C from 65_ to 125_C TSSOP Package: -6.1 mW/C from 65_ to 125_C IIII IIIIIIIIIIIIII III III III IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIII IIIIIIIII III IIII IIII IIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIII IIIIIIIII III IIII IIII IIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIII IIIIIIIII III IIII IIII IIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII RECOMMENDED OPERATING CONDITIONS Symbol VCC Vin, Vout Parameter DC Supply Voltage (Referenced to GND) Min Max Unit 2.0 6.0 V 0 VCC V - 55 + 125 _C 0 0 0 1000 500 400 ns DC Input Voltage, Output Voltage (Referenced to GND) TA Operating Temperature, All Package Types tr, tf Input Rise and Fall Time (Figure 1) VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) Symbol VIH Parameter Minimum High-Level Input Voltage Test Conditions Vout = 0.1 V or VCC - 0.1 V |Iout| v 20 mA VIL Maximum Low-Level Input Voltage VOH Minimum High-Level Output Voltage Maximum Low-Level Output Voltage Guaranteed Limit - 55 to 25_C v 85_C v 125_C Unit V 2.0 3.0 4.5 6.0 1.5 2.1 3.15 4.2 1.5 2.1 3.15 4.2 1.5 2.1 3.15 4.2 Vout = 0.1 V or VCC - 0.1 V |Iout| v 20 mA 2.0 3.0 4.5 6.0 0.5 0.9 1.35 1.8 0.5 0.9 1.35 18 0.5 0.9 1.35 1.8 V Vin = VIH or VIL |Iout| v 20 mA 2.0 4.5 6.0 1.9 4.4 5.9 1.9 4.4 5.9 1.9 4.4 5.9 V 3.0 4.5 6.0 2.48 3.98 5.48 2.34 3.84 5.34 2.2 3.7 5.2 Vout = 0.1 V or VCC - 0.1 V |Iout| v 20 mA 2.0 4.5 6.0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 Vin = VIH or VIL 3.0 4.5 6.0 0.26 0.26 0.26 0.33 0.33 0.33 0.4 0.4 0.4 Vin = VIH or VIL VOL VCC V |Iout| 2.4mA |Iout| v 6.0 mA |Iout| v 7.8 mA |Iout| 2.4mA |Iout| v 6.0 mA |Iout| v 7.8 mA V Iin Maximum Input Leakage Current Vin = VCC or GND 6.0 0.1 1.0 1.0 mA IOZ Maximum Three-State Leakage Current Output in High-Impedance State Vin = VIL or VIH Vout = VCC or GND 6.0 - 0.5 - 5.0 - 10 mA ICC Maximum Quiescent Supply Current (per Package) Vin = VCC or GND IIoutI = 0 mA 6.0 4.0 40 160 mA http://onsemi.com 3 MC74HC573A IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIII IIIIIIIIIIIIIIIII III IIIII IIII IIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIII III IIIII IIII IIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIII III IIIII IIII IIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIII III IIIII IIII IIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIII IIIIIIII IIIIIIIII IIIIIIII IIIIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6.0 ns) Symbol VCC V Parameter Guaranteed Limit - 55 to 25_C v 85_C v 125_C Unit tPLH, tPHL Maximum Propagation Delay, Input D to Q (Figures 1 and 5) 2.0 3.0 4.5 6.0 150 100 30 26 190 140 38 33 225 180 45 38 ns tPLH, tPHL Maximum Propagation Delay, Latch Enable to Q (Figures 2 and 5) 2.0 3.0 4.5 6.0 160 105 32 27 200 145 40 34 240 190 48 41 ns tPLZ, tPHZ Maximum Propagation Delay, Output Enable to Q (Figures 3 and 6) 2.0 3.0 4.5 6.0 150 100 30 26 190 125 38 33 225 150 45 38 ns tPZL, tPZH Maximum Propagation Delay, Output Enable to Q (Figures 3 and 6) 2.0 3.0 4.5 6.0 150 100 30 26 190 125 38 33 225 150 45 38 ns tTLH, tTHL Maximum Output Transition Time, Any Output (Figures 1 and 5) 2.0 3.0 4.5 6.0 60 27 12 10 75 32 15 13 90 36 18 15 ns Cin Maximum Input Capacitance 10 10 10 pF Cout Maximum 3-State Output Capacitance (Output in High-Impedance State) 15 15 15 pF Typical @ 25C, VCC = 5.0 V CPD 23 Power Dissipation Capacitance (Per Enabled Output)* pF * Used to determine the no-load dynamic power consumption: P D = CPD VCC 2 f + ICC VCC . IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIII IIIII IIIIII IIIII IIIIII IIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIII III III III III III III III III II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIII III III III III III III III III II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII TIMING REQUIREMENTS (CL = 50 pF, Input tr = tf = 6.0 ns) Guaranteed Limit Symbol Parameter Figure VCC V - 55 to 25_C Min Max v 85_C Min Max v 125_C Min Max Unit tsu Minimum Setup Time, Input D to Latch Enable 4 2.0 3.0 4.5 6.0 50 40 10 9.0 65 50 13 11 75 60 15 13 ns th Minimum Hold Time, Latch Enable to Input D 4 2.0 3.0 4.5 6.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 ns tw Minimum Pulse Width, Latch Enable 2 2.0 3.0 4.5 6.0 75 60 15 13 95 80 19 16 110 90 22 19 ns tr, tf Maximum Input Rise and Fall Times 1 2.0 3.0 4.5 6.0 http://onsemi.com 4 1000 800 500 400 1000 800 500 400 1000 800 500 400 ns MC74HC573A SWITCHING WAVEFORMS VCC tr LATCH ENABLE tf VCC 90% 50% 10% INPUT D 50% GND tw GND tPLH tPHL 90% 50% 10% Q tPLH tTHL tTLH 50% Q Figure 1. OUTPUT ENABLE Figure 2. VCC 50% VALID GND tPLZ tPZL Q HIGH IMPEDANCE VM tPZH Q tPHZ 10% VOL 90% VOH VM MC74HC573A: VM = VOH x 0.5 MC74HCT573A: VM = 1.3 V @ VCC = 3 V GND tSU HIGH IMPEDANCE Figure 4. D1 OUTPUT DEVICE UNDER TEST D2 CL* D3 *Includes all probe and jig capacitance 2 D4 3 4 5 6 Figure 5. Test Circuit D5 D6 TEST POINT CL* VCC GND TEST POINT 1 kW th 50% LATCH ENABLE D0 OUTPUT VCC 50% INPUT D Figure 3. DEVICE UNDER TEST tPHL CONNECT TO VCC WHEN TESTING tPLZ AND tPZL. CONNECT TO GND WHEN TESTING tPHZ AND tPZH. D7 7 8 9 LATCH ENABLE OUTPUT ENABLE *Includes all probe and jig capacitance Figure 6. Test Circuit D Q LE 19 D Q LE 18 D Q LE 17 D Q LE 16 D Q LE 15 D Q LE 14 D Q LE 13 D Q LE 12 11 1 Figure 7. EXPANDED LOGIC DIAGRAM http://onsemi.com 5 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 MC74HC573A PACKAGE DIMENSIONS PDIP-20 N SUFFIX CASE 738-03 ISSUE E NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. -A- 20 11 1 10 B L C -T- K SEATING PLANE M N E G F J D 20 PL 20 PL 0.25 (0.010) 0.25 (0.010) M T A M T B M DIM A B C D E F G J K L M N INCHES MIN MAX 1.010 1.070 0.240 0.260 0.150 0.180 0.015 0.022 0.050 BSC 0.050 0.070 0.100 BSC 0.008 0.015 0.110 0.140 0.300 BSC 0_ 15 _ 0.020 0.040 MILLIMETERS MIN MAX 25.66 27.17 6.10 6.60 3.81 4.57 0.39 0.55 1.27 BSC 1.27 1.77 2.54 BSC 0.21 0.38 2.80 3.55 7.62 BSC 0_ 15_ 0.51 1.01 M SOIC-20 DW SUFFIX CASE 751D-05 ISSUE G A 20 11 X 45 _ E h 1 10 20X B B 0.25 M T A S B S A L H M 10X 0.25 NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF B DIMENSION AT MAXIMUM MATERIAL CONDITION. q B M D 18X e A1 SEATING PLANE C T http://onsemi.com 6 DIM A A1 B C D E e H h L q MILLIMETERS MIN MAX 2.35 2.65 0.10 0.25 0.35 0.49 0.23 0.32 12.65 12.95 7.40 7.60 1.27 BSC 10.05 10.55 0.25 0.75 0.50 0.90 0_ 7_ MC74HC573A PACKAGE DIMENSIONS TSSOP-20 DT SUFFIX CASE 948E-02 ISSUE C 20X 0.15 (0.006) T U 2X L K REF 0.10 (0.004) S L/2 20 M T U S V IIII IIII IIII K K1 S J J1 11 B -U- PIN 1 IDENT 1 SECTION N-N 0.25 (0.010) N 10 M 0.15 (0.006) T U S N A -V- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. F DETAIL E -W- C G D H DETAIL E 0.100 (0.004) -T- SEATING PLANE DIM A B C D F G H J J1 K K1 L M SOLDERING FOOTPRINT 7.06 1 0.65 PITCH 16X 0.36 16X 1.26 DIMENSIONS: MILLIMETERS http://onsemi.com 7 MILLIMETERS MIN MAX 6.40 6.60 4.30 4.50 --1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.27 0.37 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.252 0.260 0.169 0.177 --0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.011 0.015 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ MC74HC573A PACKAGE DIMENSIONS SOEIAJ-20 F SUFFIX CASE 967-01 ISSUE A 20 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). LE 11 Q1 E HE 1 M_ L 10 DETAIL P Z D e VIEW P A A1 b 0.13 (0.005) c M 0.10 (0.004) DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --2.05 0.05 0.20 0.35 0.50 0.15 0.25 12.35 12.80 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 _ 0_ 0.70 0.90 --0.81 INCHES MIN MAX --0.081 0.002 0.008 0.014 0.020 0.006 0.010 0.486 0.504 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 _ 0_ 0.028 0.035 --0.032 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 8 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC74HC573A/D