P6SMBJ12CA - DIOTEC SEMICONDUCTOR AG

TwinDie™ 1.2V DDR4 SDRAM

MT40A1G16 – 64 Meg x 16 x 16 Banks x 1 Ranks

Description

The 16Gb (TwinDie™) DDR4 SDRAM uses

Micron’s 8Gb DDR4 SDRAM die; two x8s combined to

make one x16. Similar signals as mono x16, there is

one extra ZQ connection for faster ZQ Calibration and

a BG1 control required for x8 addressing. Refer to Mi-

cron’s 8Gb DDR4 SDRAM data sheet (x8 option) for

the specifications not included in this document.

Specifications for base part number MT40A1G8 corre-

late to TwinDie manufacturing part number

MT40A1G16.

Features

• Uses two x8 8Gb Micron die to make one x16

• Single rank TwinDie

• VDD = VDDQ = 1.2V (1.14–1.26V)

• 1.2V VDDQ-terminated I/O

• JEDEC-standard ball-out

• Low-profile package

• TC of 0°C to 95°C

– 0°C to 85°C: 8192 refresh cycles in 64ms

– 85°C to 95°C: 8192 refresh cycles in 32ms

Options Marking

• Configuration

– 64 Meg x 16 x 16 banks x 1 rank 1G16

• 96-ball FBGA package (Pb-free)

– 9.5mm x 14mm x 1.2mm Die Rev :A HBA

– 8.0mm x 14mm x 1.2mm Die Rev :B,

WBU

– 7.5mm x 13.5mm x 1.2mm Die Rev :E KNR

• Timing – cycle time1

– 0.625ns @ CL = 22 (DDR4-3200) -062E

– 0.682ns @ CL = 21 (DDR4-2933) -068

– 0.750ns @ CL = 19 (DDR4-2666) -075

– 0.750ns @ CL = 18 (DDR4-2666) -075E

– 0.833ns @ CL = 17(DDR4-2400) -083

– 0.833ns @ CL = 16 (DDR4-2400) -083E

– 0.937ns @ CL = 15 (DDR4-2133) -093E

– 1.071ns @ CL = 13 (DDR4-1866) -107E

• Self refresh

– Standard None

• Operating temperature

– Commercial (0°C ≤ TC ≤ 95°C) None

• Revision :A

:B, D

Note: 1. CL = CAS (READ) latency.

Table 1: Key Timing Parameters

Speed Grade1Data Rate (MT/s) Target tRCD-tRP-CL tRCD (ns) tRP (ns) CL (ns)

-062Y 3200 22-22-22 13.75 (13.32) 13.75 (13.32) 13.75 (13.32)

-062E 3200 22-22-22 13.75 13.75 13.75

-068 2933 21-21-21 14.32 (13.75) 14.32 (13.75) 14.32 (13.75)

-075E 2666 18-18-18 13.50 13.50 13.50

-075 2666 19-19-19 14.25 14.25 14.25

-083E 2400 16-16-16 13.32 13.32 13.32

-083 2400 17-17-17 14.16 (13.75) 14.16 (13.75) 14.16 (13.75)

-093E 2133 15-15-15 14.06 (13.50) 14.06 (13.50) 14.06 (13.50)

-093 2133 16-16-16 15.00 15.00 15.00

-107E 1866 13-13-13 13.92 (13.50) 13.92 (13.50) 13.92 (13.50)

Note: 1. Refer to Speed Bin Tables for additional details.

16Gb: x16 TwinDie Single Rank DDR4 SDRAM

Description

CCMTD-1725822587-9947

16gb_x16_1cs_TwinDie.pdf - Rev. G 06/18 EN 1Micron Technology, Inc. reserves the right to change products or specifications without notice.

Products and specifications discussed herein are subject to change by Micron without notice.

Table 2: Addressing

Parameter 1024 Meg x 16

Configuration 64 Meg x 16 x 16 banks x 1 rank

Bank group address BG[1:0]

Bank count per group 4

Bank address in bank group BA[1:0]

Row addressing 64K (A[15:0])

Column addressing 1K (A[9:0])

Page size 1KB

Note: 1. Page size is per bank, calculated as follows:

Page size = 2COLBITS × ORG/8, where COLBIT = the number of column address bits and ORG = the number of

DQ bits.

16Gb: x16 TwinDie Single Rank DDR4 SDRAM

Description

CCMTD-1725822587-9947

16gb_x16_1cs_TwinDie.pdf - Rev. G 06/18 EN 2Micron Technology, Inc. reserves the right to change products or specifications without notice.

Important Notes and Warnings

Micron Technology, Inc. ("Micron") reserves the right to make changes to information published in this document,

including without limitation specifications and product descriptions. This document supersedes and replaces all

information supplied prior to the publication hereof. You may not rely on any information set forth in this docu-

ment if you obtain the product described herein from any unauthorized distributor or other source not authorized

by Micron.

Automotive Applications. Products are not designed or intended for use in automotive applications unless specifi-

cally designated by Micron as automotive-grade by their respective data sheets. Distributor and customer/distrib-

utor shall assume the sole risk and liability for and shall indemnify and hold Micron harmless against all claims,

costs, damages, and expenses and reasonable attorneys' fees arising out of, directly or indirectly, any claim of

product liability, personal injury, death, or property damage resulting directly or indirectly from any use of non-

automotive-grade products in automotive applications. Customer/distributor shall ensure that the terms and con-

ditions of sale between customer/distributor and any customer of distributor/customer (1) state that Micron

products are not designed or intended for use in automotive applications unless specifically designated by Micron

as automotive-grade by their respective data sheets and (2) require such customer of distributor/customer to in-

demnify and hold Micron harmless against all claims, costs, damages, and expenses and reasonable attorneys'

fees arising out of, directly or indirectly, any claim of product liability, personal injury, death, or property damage

resulting from any use of non-automotive-grade products in automotive applications.

Critical Applications. Products are not authorized for use in applications in which failure of the Micron compo-

nent could result, directly or indirectly in death, personal injury, or severe property or environmental damage

("Critical Applications"). Customer must protect against death, personal injury, and severe property and environ-

mental damage by incorporating safety design measures into customer's applications to ensure that failure of the

Micron component will not result in such harms. Should customer or distributor purchase, use, or sell any Micron

component for any critical application, customer and distributor shall indemnify and hold harmless Micron and

its subsidiaries, subcontractors, and affiliates and the directors, officers, and employees of each against all claims,

costs, damages, and expenses and reasonable attorneys' fees arising out of, directly or indirectly, any claim of

product liability, personal injury, or death arising in any way out of such critical application, whether or not Mi-

cron or its subsidiaries, subcontractors, or affiliates were negligent in the design, manufacture, or warning of the

Micron product.

Customer Responsibility. Customers are responsible for the design, manufacture, and operation of their systems,

applications, and products using Micron products. ALL SEMICONDUCTOR PRODUCTS HAVE INHERENT FAIL-

URE RATES AND LIMITED USEFUL LIVES. IT IS THE CUSTOMER'S SOLE RESPONSIBILITY TO DETERMINE

WHETHER THE MICRON PRODUCT IS SUITABLE AND FIT FOR THE CUSTOMER'S SYSTEM, APPLICATION, OR

PRODUCT. Customers must ensure that adequate design, manufacturing, and operating safeguards are included

in customer's applications and products to eliminate the risk that personal injury, death, or severe property or en-

vironmental damages will result from failure of any semiconductor component.

Limited Warranty. In no event shall Micron be liable for any indirect, incidental, punitive, special or consequential

damages (including without limitation lost profits, lost savings, business interruption, costs related to the removal

or replacement of any products or rework charges) whether or not such damages are based on tort, warranty,

breach of contract or other legal theory, unless explicitly stated in a written agreement executed by Micron's duly

authorized representative.

16Gb: x16 TwinDie Single Rank DDR4 SDRAM

Important Notes and Warnings

CCMTD-1725822587-9947

16gb_x16_1cs_TwinDie.pdf - Rev. G 06/18 EN 3Micron Technology, Inc. reserves the right to change products or specifications without notice.

Ball Assignments

Figure 1: 96-Ball x16 SR DDP Ball Assignments

1 2 3 4 6 7 8 95

VDDQ

VPP

VDDQ

VDD

VSS

VSSQ

VDDQ

VSSQ

VDD

VSS

VDD

VREFCA

VSS

RESET_n

VDD

VSS VSS

VSSQ

VSS

UDQ4

VSSQ

VDDQ

LDQ0

LDQ4

VDDQ

CKE

WE_n/A14

BG0 BG1

BA0

A11

UDQ0

VDD

UDQ2

UDQ6

VSSQ

LDQS_c

LDQS_t

LDQ2

LDQ6

ODT

ACT_n

A10/AP

PAR

UDQS_c

UDQS_t

UDQ3

UDQ7

LDQ1

VDD

LDQ3

LDQ7

CK_t

CS_n

A12/BC_n

VSSQ

UDQ1

UDQ5

VSSQ

VDDQ

VSS

LDQ5

VDDQ

CK_c

RAS_n/A16

CAS-n/A15

BA1

A13

VDDQ

VDD

VSSQ

VDDQ

UZQ

LZQ

VSSQ

VDD

VSS

VDD

TEN

VPP

VDD

NF/LDM_n/

LDBI_n

ALERT_n

NF/UDM_n/

UDBI_n

Notes: 1. See Ball Descriptions in the monolithic data sheet.

2. A slash “/” defines a selectable function. For example: Ball E2 = NF/UDM_n/UDBI_n

where either NF, UDM_n, or UDBI_n is defined via MRS.

16Gb: x16 TwinDie Single Rank DDR4 SDRAM

Ball Assignments

CCMTD-1725822587-9947

16gb_x16_1cs_TwinDie.pdf - Rev. G 06/18 EN 4Micron Technology, Inc. reserves the right to change products or specifications without notice.

Functional Block Diagrams

Figure 2: Functional Block Diagram (128 Meg x 16 x 16 Banks x 1 Rank)

ACT_n

CAS_n/A15

RAS_n/A16

WE_n/A14

PAR

VrefCA

CK_t

CK_c

LDQ[7:0]

LDQS_t

LDQS_c

A[13:0]

BA[1:0]

BG[1:0]

Byte 0

(64 Meg x 8 x 16 banks)

Byte 1

(64 Meg x 8 x 16 banks)

(128 Meg x 16 x 16 banks)

CS_n

CKE

ODT

UZQ LZQ

UDM_n/

UDBI_n

LDM_n/

LDBI_n

TEN

RESET_n

ALERT_n

UDQ[7:0]

UDQS_t

UDQS_c

16Gb: x16 TwinDie Single Rank DDR4 SDRAM

Functional Block Diagrams

CCMTD-1725822587-9947

16gb_x16_1cs_TwinDie.pdf - Rev. G 06/18 EN 5Micron Technology, Inc. reserves the right to change products or specifications without notice.

Connectivity Test Mode

Connectivity test (CT) mode for the x16 TwinDie single rank (SR) device is the same as

two mono x8 devices connected in parallel. The mapping is restated for clarity.

Minimum Terms Definition for Logic Equations

The test input and output pins are related by the following equations, where INV de-

notes a logical inversion operation and XOR a logical exclusive OR operation:

MT0 = XOR (A1, A6, PAR)

MT1 = XOR (A8, ALERT_n, A9)

MT2 = XOR (A2, A5, A13)

MT3 = XOR (A0, A7, A11)

MT4 = XOR (CK_c, ODT, CAS_n/A15)

MT5 = XOR (CKE, RAS_n/A16, A10/AP)

MT6 = XOR (ACT_n, A4, BA1)

MT7L = XOR (BG1, LDM_n/LDBI_n, CK_t)

MT7U = XOR (BG1, UDM_n/UDBI_n, CK_t)

MT8 = XOR (WE_n/A14, A12 / BC, BA0)

MT9 = XOR (BG0, A3, RESET_n and TEN)

Logic Equations for a x16 TwinDie, SR Device

Byte 0 Byte 1

LDQ0 = MT0 UDQ0 = MT0

LDQ1 = MT1 UDQ1 = MT1

LDQ2 = MT2 UDQ2 = MT2

LDQ3 = MT3 UDQ3 = MT3

LDQ4 = MT4 UDQ4 = MT4

LDQ5 = MT5 UDQ5 = MT5

LDQ6 = MT6 UDQ6 = MT6

LDQ7 = MT7L UDQ7 = MT7U

LDQS_t = MT8 UDQS_t = MT8

LDQS_c = MT9 UDQS_c = MT9

x16 TwinDie, SR Internal Connections

The figure below shows the internal connections of the x16 TwinDie, SR. The diagram

shows why byte 0 and byte 1 outputs have the same logic equations except LDQ7 and

UDQ7; they are different because the DM_n/DBI_n pins are not common for each byte.

16Gb: x16 TwinDie Single Rank DDR4 SDRAM

Connectivity Test Mode

CCMTD-1725822587-9947

16gb_x16_1cs_TwinDie.pdf - Rev. G 06/18 EN 6Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 3: x16 TwinDie, SR

ACT_n

CAS_n/A15

RAS_n/A16

WE_n/A14

PAR

VREFCA

CK_t

CK_c

LDQ[7:0]

LDQS_t

LDQS_c

A[13:0]

BA[1:0]

BG[1:0]

Byte 1

CS_n

CKE

ODT

UZQ LZQ

UDM_n/

UDBI_n

LDM_n/

LDBI_n

TEN

RESET_n

ALERT_n

UDQ[7:0]

UDQS_t

UDQS_c

Byte 0

16Gb: x16 TwinDie Single Rank DDR4 SDRAM

Connectivity Test Mode

CCMTD-1725822587-9947

16gb_x16_1cs_TwinDie.pdf - Rev. G 06/18 EN 7Micron Technology, Inc. reserves the right to change products or specifications without notice.

Electrical Specifications – Leakages

Table 3: Input and Output Leakages

Symbol Parameter Min Max Units Notes

IIInput leakage current

Any input 0V ≤ VIN ≤ VDD,

VREF pin 0V ≤ VIN ≤ 1.1V

(All other pins not under test = 0V)

–4 4 µA 1

IVREF VREF supply leakage current

VREFDQ = VDD/2 or VREFCA = VDD/2

(All other pins not under test = 0V)

–4 4 µA 2

IZQ Input leakage on ZQ pin –50 10 µA

ITEN Input leakage on TEN pin –12 20 µA

IOZPD Output leakage: VOUT = VDDQ – 10 µA 3

IOZPU Output leakage: VOUT = VSSQ –50 – µA 3, 4

Notes: 1. Any input 0V < Vin < 1.1V

2. VREFCA = VDD/2, VDD at valid level.

3. DQs are disabled.

4. ODT is disabled with the ODT input HIGH.

Temperature and Thermal Impedance

It is imperative that the DDR4 SDRAM device’s temperature specifications, shown in

the following table, be maintained in order to ensure the junction temperature is in the

proper operating range to meet data sheet specifications. An important step in main-

taining the proper junction temperature is using the device’s thermal impedances cor-

rectly. The thermal impedances listed in Table 5 (page 9) apply to the current die re-

vision and packages.

Incorrectly using thermal impedances can produce significant errors. Read Micron

technical note TN-00-08, “Thermal Applications,” prior to using the values listed in the

thermal impedance table. For designs that are expected to last several years and require

the flexibility to use several DRAM die shrinks, consider using final target theta values

(rather than existing values) to account for increased thermal impedances from the die

size reduction.

The DDR4 SDRAM device’s safe junction temperature range can be maintained when

the TC specification is not exceeded. In applications where the device’s ambient tem-

perature is too high, use of forced air and/or heat sinks may be required to satisfy the

case temperature specifications.

16Gb: x16 TwinDie Single Rank DDR4 SDRAM

Electrical Specifications – Leakages

CCMTD-1725822587-9947

16gb_x16_1cs_TwinDie.pdf - Rev. G 06/18 EN 8Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 4: Thermal Characteristics

Notes 1–3 apply to entire table

Parameter Symbol Value Units Notes

Operating temperature TC0 to 85 °C

0 to 95 °C 4

Notes: 1. MAX operating case temperature TC is measured in the center of the package, as shown

below.

2. A thermal solution must be designed to ensure that the device does not exceed the

maximum TC during operation.

3. Device functionality is not guaranteed if the device exceeds maximum TC during

operation.

4. If TC exceeds 85°C, the DRAM must be refreshed externally at 2x refresh, which is a 3.9µs

interval refresh rate. The use of self refresh temperature (SRT) or automatic self refresh

(ASR), if available, must be enabled.

Figure 4: Temperature Test Point Location

Test point

Length (L)

Width (W)

0.5 (W)

0.5 (L)

Table 5: Thermal Impedance

Die Rev.

Substrate

conductivity

Θ JA (°C/W)

Airflow =

0m/s

Θ JA (°C/W)

Airflow =

1m/s

Θ JA (°C/W)

Airflow =

2m/s Θ JB (°C/W) Θ JC (°C/W) Notes

ALow TBD TBD TBD N/A TBD 1

High TBD TBD TBD TBD N/A

B, D Low 43.9 33.0 29.5 N/A 3.3 1

High 27.1 21.7 20.1 10.5 N/A

ELow TBD TBD TBD N/A TBD 1

High TBD TBD TBD TBD N/A

Note: 1. Thermal resistance data is based on a number of samples from multiple lots and should

be viewed as a typical number.

16Gb: x16 TwinDie Single Rank DDR4 SDRAM

Electrical Specifications – Leakages

CCMTD-1725822587-9947

16gb_x16_1cs_TwinDie.pdf - Rev. G 06/18 EN 9Micron Technology, Inc. reserves the right to change products or specifications without notice.

DRAM Package Electrical Specifications

Table 6: DRAM Package Electrical Specifications for x16 Devices

Notes 1–4 apply to the entire table

Parameter Symbol

DDR4-1600, -1866 DDR4-2133, -2400 DDR4-2666, -2933

Unit NotesMin Max Min Max Min Max

Input/

output

Zpkg ZIO 30 50 30 50 30 50 ohm 5, 6

Package delay TdIO 60 120 60 120 60 120 ps 6 , 7

Lpkg LIO – 5.0 – 5.0 – 5.0 nH

Cpkg CIO – 3.0 – 3.0 – 3.0 pF

DQSL_t/

DQSL_c/

DQSU_t/

DQSU_c

Zpkg ZIO DQS 30 50 30 50 30 50 ohm 5

Package delay TdIO DQS 60 120 60 120 60 120 ps 7

Lpkg LIO DQS – 5.0 – 5.0 – 5.0 nH

Cpkg CIO DQS – 3.0 – 3.0 – 3.0 pF

DQSL_t/

DQSL_c,

DQSU_t/

DQSU_c,

Delta Zpkg DZIO DQS – 20 – 20 – 20 ohm 5, 8

Delta delay DTdIO DQS – 45 – 45 – 45 ps 7, 8

Input CTRL

pins

Zpkg ZI CTRL 35 65 35 65 35 65 ohm 5, 9

Package delay TdI CTRL 75 120 75 120 75 120 ps 7, 9

Lpkg LI CTRL – 6.5 – 6.5 – 6.5 nH

Cpkg CI CTRL – 2.5 – 2.5 – 2.5 pF

Input CMD

ADD pins

Zpkg ZI ADD CMD 35 65 35 65 35 65 ohm 5, 10

Package delay TdI ADD CMD 70 125 70 125 70 125 ps 7, 10

Lpkg LI ADD CMD – 6.5 – 6.5 – 6.5 nH

Cpkg CI ADD CMD – 3.0 – 3.0 – 3.0 pF

CK_t, CK_c Zpkg ZCK 30 55 30 55 30 55 ohm 5

Package delay TdCK 80 135 80 135 80 135 ps 7

Delta Zpkg DZDCK – 0.5 – 0.5 – 0.5 ohm 5, 11

Delta delay DTdDCK – 1.2 – 1.2 – 1.2 ps 7, 11

Input CLK Lpkg LI CLK – 6.0 – 6.0 – 6.0 nH

Cpkg CI CLK – 3.0 – 3.0 – 3.0 pF

ZQ Zpkg ZO ZQ – 40 – 40 – 40 ohm 5

ZQ delay TdO ZQ 30 135 30 135 30 135 ps 7

ALERT Zpkg ZO ALERT 30 55 30 55 30 55 ohm 5

ALERT delay TdO ALERT 65 110 65 110 65 110 ps 7

Notes: 1. The package parasitic (L and C) are not subject to production testing. If the package par-

asitic (L and C) are measured, the capacitance is measured with VDD, VDDQ, VSS, and VSSQ

shorted with all other signal pins floating. The inductance is measured with VDD, VDDQ,

VSS, and VSSQ shorted and all other signal pins shorted at the die, not pin, side.

2. Package implementations should satisfy targets if the Zpkg and package delay fall with-

in the ranges shown, and the maximum Lpkg and Cpkg do not exceed the maximum

16Gb: x16 TwinDie Single Rank DDR4 SDRAM

DRAM Package Electrical Specifications

CCMTD-1725822587-9947

16gb_x16_1cs_TwinDie.pdf - Rev. G 06/18 EN 10 Micron Technology, Inc. reserves the right to change products or specifications without notice.

values shown. The package design targets are provided for reference, system signal sim-

ulations should not use these values but use the Micron package model.

3. It is assumed that Lpkg can be approximated as Lpkg = ZO × Td.

4. It is assumed that Cpkg can be approximated as Cpkg = Td/ZO.

5. Package-only impedance (Zpkg) is calculated based on the Lpkg and Cpkg total for a

given pin where: Zpkg (total per pin) = SQRT (Lpkg/Cpkg).

6. ZIO and TdIO apply to DQ, DM, DQS_c, DQS_t, TDQS_t, and TDQS_c.

7. Package-only delay (Tpkg) is calculated based on Lpkg and Cpkg total for a given pin

where: Tdpkg (total per pin) = SQRT (Lpkg × Cpkg).

8. Absolute value of ZIO (DQS_t), ZIO (DQS_c) for impedance (Z) or absolute value of TdIO

(DQS_t), TdIO (DQS_c) for delay (Td).

9. ZI CTRL and TdI CTRL apply to ODT, CS_n, and CKE.

10. ZI ADD CMD and TdI ADD CMD apply to A[17:0], BA[1:0], BG[1:0], RAS_n CAS_n, and WE_n.

11. Absolute value of ZCK_t, ZCK_c for impedance (Z) or absolute value of TdCK_t, TdCK_c

for delay (Td).

Table 7: Pad Input/Output Capacitance

Parameter Symbol

DDR4-1600,

-1866, -2133

DDR4-2400,

-2666 DDR4-2933

Unit NotesMin Max Min Max Min Max

Input/output capacitance: DQ,

DM, DQS_t, DQS_c, TDQS_t,

TDQS_c

CIO 1.8 2.8 1.8 2.8 1.8 2.8 pF 1, 2, 3

Input capacitance: CK_t and

CK_c

CCK 2.1 2.9 2.1 2.9 2.1 2.9 pF 1, 2, 3, 4

Input capacitance delta: CK_t

and CK_c

CDCK 0 0.05 0 0.05 0 0.05 pF 1, 2, 3, 5

Input/output capacitance delta:

DQS_t and DQS_c

CDDQS 0 0.05 0 0.05 0 0.05 pF 1, 3

Input capacitance: CTRL, ADD,

CMD input-only pins

CI1.6 2.6 1.6 2.6 1.6 2.6 pF 1, 3, 6

Input capacitance delta: All

CTRL input-only pins

CDI_CTRL –0 .9 0.9 –0 .9 0.9 –0 .9 0.9 pF 1, 3, 7

Input capacitance delta: All

ADD/CMD input-only pins

CDI_ADD_CMD –0 .9 0.9 –0 .9 0.9 –0 .9 0.9 pF 1, 3, 8, 9

Input/output capacitance delta:

DQ, DM, DQS_t, DQS_c, TDQS_t,

TDQS_c

CDIO –0.16 0.16 –0.16 0.16 –0.16 0.16 pF 1, 2, 10,

Input/output capacitance:

ALERT pin

CALERT 1.1 2.3 1.1 2.3 1.1 2.3 pF 1, 3

Input/output capacitance: ZQ

CZQ – 3.7 – 3.7 – 3.7 pF 1, 3, 12

Input/output capacitance: TEN

CTEN 0.2 2.3 0.2 2.3 0.2 2.3 pF 1, 3, 13

Notes: 1. Although the DM, TDQS_t, and TDQS_c pins have different functions, the loading

matches DQ and DQS.

16Gb: x16 TwinDie Single Rank DDR4 SDRAM

DRAM Package Electrical Specifications

CCMTD-1725822587-9947

16gb_x16_1cs_TwinDie.pdf - Rev. G 06/18 EN 11 Micron Technology, Inc. reserves the right to change products or specifications without notice.

2. This parameter is not subject to a production test; it is verified by design and characteri-

zation and are provided for reference; system signal simulations should not use these

values but use the Micron package model. The capacitance, if and when, is measured ac-

cording to the JEP147 specification, “Procedure for Measuring Input Capacitance Using

a Vector Network Analyzer (VNA),” with VDD, VDDQ, VSS, and VSSQ applied and all other

pins floating (except the pin under test, CKE, RESET_n and ODT, as necessary). VDD =

VDDQ = 1.5V, VBIAS = VDD/2 and on-die termination off.

3. This parameter applies to SR x16 TwinDie, obtained by de-embedding the package L and

C parasitics.

4. CDIO = CIO(DQ, DM) - 0.5 × (CIO(DQS_t) + CIO(DQS_c)).

5. Absolute value of CIO (DQS_t), CIO (DQS_c)

6. Absolute value of CCK_t, CCK_c

7. CI applies to ODT, CS_n, CKE, A[15:0], BA[1:0], RAS_n, CAS_n, and WE_n.

8. CDI_CTRL applies to ODT, CS_n, and CKE.

9. CDI_CTRL = CI(CTRL) - 0.5 × (CI(CLK_t) + CI(CLK_c)).

10. CDI_ADD_CMD applies to A[15:0], BA1:0], RAS_n, CAS_n and WE_n.

11. CDI_ADD_CMD = CI(ADD_CMD) - 0.5 × (CI(CLK_t) + CI(CLK_c)).

12. Maximum external load capacitance on ZQ pin: 5pF.

13. Only applicable if TEN pin does not have an internal pull-up.

16Gb: x16 TwinDie Single Rank DDR4 SDRAM

DRAM Package Electrical Specifications

CCMTD-1725822587-9947

16gb_x16_1cs_TwinDie.pdf - Rev. G 06/18 EN 12 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Current Specifications – Limits

Table 8: x16 IDD, IPP, and IDDQ Current Limits – Rev. A

Symbol DDR4-21331DDR4-2400 DDR4-2666 DDR4-2933 Unit Notes

IDD0: One bank ACTIVATE-to-PRECHARGE

current

110 120 130 TBD mA 2, 3, 4

IPP0: One bank ACTIVATE-to-PRECHARGE IPP

current

6 6 6 TBD mA

IDD1: One bank ACTIVATE-to-READ-to-PRE-

CHARGE current

140 150 160 TBD mA 3, 4, 5

IDD2N: Precharge standby current 90 100 110 TBD mA 4, 6, 7, 8,

9, 10, 11

IDD2NT: Precharge standby ODT current 110 120 130 TBD mA 4, 11

IDD2P: Precharge power-down current 50 60 70 TBD mA 4, 11

IDD2Q: Precharge quiet standby current 90 90 100 TBD mA 4, 11

IDD3N: Active standby current 110 110 120 TBD mA 4, 11

IPP3N: Active standby IPP current 6 6 6 TBD mA

IDD3P: Active power-down current 70 80 80 TBD mA 4, 11

IDD4R: Burst read current 300 300 350 TBD mA 4, 14, 13,

IDD4W: Burst write current 300 320 350 TBD mA 4, 11, 15,

16, 17,

IDD5R: Distributed refresh current (1X REF) 128 128 136 TBD mA 4, 19, 20

IPP5R: Distributed refresh IPP current (1X

REF)

10 10 10 TBD mA

IDD6N: Self refresh current; 0–85°C 60 60 60 TBD mA 11, 21

IDD6E: Self refresh current; 0–95°C 70 70 70 TBD mA 11, 22

IDD6R: Self refresh current; 0–45°C 50 50 50 TBD mA 11, 23,

IDD6A: Auto self refresh current (25°C) 40 40 40 TBD mA 11, 24

IDD6A: Auto self refresh current (45°C) 50 50 50 TBD mA 11, 24

IDD6A: Auto self refresh current (75°C) 70 70 70 TBD mA 11, 24

IPP6X: Auto self refresh current IPP current 10 10 10 TBD mA 11, 24

IDD7: Bank interleave read current 400 410 430 TBD mA 4

IPP7: Bank interleave read IPP current 30 30 30 TBD mA

IDD8: Maximum power-down current 40 40 40 TBD mA 11

Notes: 1. DDR4-1600 and DDR4-1866 use the same IDD limits as DDR4-2133.

2. When additive latency is enabled for IDD0, current changes by approximately 0%.

3. IPP0 test and limit is applicable for IDD0 and IDD1 conditions.

4. The IDD values must be derated (increased) when operated outside of the range 0°C ≤ TC

≤ 85°C:

16Gb: x16 TwinDie Single Rank DDR4 SDRAM

Current Specifications – Limits

CCMTD-1725822587-9947

16gb_x16_1cs_TwinDie.pdf - Rev. G 06/18 EN 13 Micron Technology, Inc. reserves the right to change products or specifications without notice.

When TC < 0°C: IDD2P and IDD3P must be derated by 6%; IDD4R and IDD4W must be derated

by+ 4%; and IDD7 must be derated by +11%.

When TC > 85°C: IDD0, IDD1, IDD2N, IDD2NT, IDD2Q, IDD3N, IDD3P, IDD4R, IDD4W, and IDD5R must

be derated by +3%; IDD2P must be derated by +40%.

5. When additive latency is enabled for IDD1, current changes by approximately +4%.

6. When additive latency is enabled for IDD2N, current changes by approximately 0%.

7. When DLL is disabled for IDD2N, current changes by approximately –23%.

8. When CAL is enabled for IDD2N, current changes by approximately –25%.

9. When gear-down is enabled for IDD2N, current changes by approximately 0%.

10. When CA parity is enabled for IDD2N, current changes by approximately +7%.

11. IPP3N test and limit is applicable for all IDD2x, IDD3x, IDD4x, IDD6x, and IDD8 conditions; that

is, testing IPP3N should satisfy the IPPs for the noted IDD tests.

12. When additive latency is enabled for IDD3N, current changes by approximately +0.6%.

13. When additive latency is enabled for IDD4R, current changes by approximately +5%.

14. When read DBI is enabled for IDD4R, current changes by approximately 0%.

15. When additive latency is enabled for IDD4W, current changes by approximately +4%.

16. When write DBI is enabled for IDD4W, current changes by approximately 0%.

17. When write CRC is enabled for IDD4W, current changes by approximately –3%.

18. When CA parity is enabled for IDD4W, current changes by approximately +12%.

19. When 2X REF is enabled for IDD5R, current changes by approximately –14%.

20. When 4X REF is enabled for IDD5R, current changes by approximately –33%.

21. Applicable for MR2 settings A7 = 0 and A6 = 0; manual mode with normal temperature

range of operation (0–85°C).

22. Applicable for MR2 settings A7 = 1 and A6 = 0; manual mode with extended tempera-

ture range of operation (0–95°C).

23. Applicable for MR2 settings A7 = 0 and A6 = 1; manual mode with reduced temperature

range of operation (0–45°C).

24. IDD6R and IDD6A values are typical.

Table 9: x16 IDD, IPP, and IDDQ Current Limits – Rev. B

Symbol DDR4-21331DDR4-2400 DDR4-2666 DDR4-2933 DDR4-3200 Unit Notes

IDD0: One bank ACTIVATE-to-PRE-

CHARGE current

90 96 102 108 114 mA 2, 3, 4

IPP0: One bank ACTIVATE-to-PRE-

CHARGE IPP current

6 6 6 6 6 mA

IDD1: One bank ACTIVATE-to-

READ-to-PRECHARGE current

114 120 126 132 138 mA 3, 4, 5

IDD2N: Precharge standby current 66 68 70 72 74 mA 4, 6, 7,

8, 9, 10,

IDD2NT: Precharge standby ODT

current

90 100 100 110 120 mA 4, 11

IDD2P: Precharge power-down

current

50 50 50 50 50 mA 4, 11

IDD2Q: Precharge quiet standby

current

60 60 60 60 60 mA 4, 11

IDD3N: Active standby current 80 86 92 98 104 mA 4, 11

16Gb: x16 TwinDie Single Rank DDR4 SDRAM

Current Specifications – Limits

CCMTD-1725822587-9947

16gb_x16_1cs_TwinDie.pdf - Rev. G 06/18 EN 14 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 9: x16 IDD, IPP, and IDDQ Current Limits – Rev. B (Continued)

Symbol DDR4-21331DDR4-2400 DDR4-2666 DDR4-2933 DDR4-3200 Unit Notes

IPP3N: Active standby IPP current 6 6 6 6 6 mA

IDD3P: Active power-down current 70 74 78 82 86 mA 4, 11

IDD4R: Burst read current 250 270 292 314 336 mA 4, 14,

13, 11

IDD4W: Burst write current 230 246 264 282 300 mA 4, 11,

15, 16,

17, 18

IDD5R: Distributed refresh current

(1X REF)

100 106 112 118 124 mA 4, 19,

IPP5R: Distributed refresh IPP cur-

rent (1X REF)

10 10 10 10 10 mA

IDD6N: Self refresh current; 0–85°C 60 60 60 60 60 mA 11, 21

IDD6E: Self refresh current; 0–95°C 70 70 70 70 70 mA 11, 22

IDD6R: Self refresh current; 0–45°C 40 40 40 40 40 mA 11, 23,

IDD6A: Auto self refresh current

(25°C)

17.2 17.2 17.2 17.2 17.2 mA 11, 24

IDD6A: Auto self refresh current

(45°C)

40 40 40 40 40 mA 11, 24

IDD6A: Auto self refresh current

(75°C)

60 60 60 60 60 mA 11, 24

IPP6X: Auto self refresh current IPP

current

10 10 10 10 10 mA 11, 24

IDD7: Bank interleave read current 340 350 360 370 380 mA 4

IPP7: Bank interleave read IPP cur-

rent

30 30 30 30 30 mA

IDD8: Maximum power-down cur-

rent

50 50 50 50 50 mA 11

Notes: 1. DDR4-1600 and DDR4-1866 use the same IDD limits as DDR4-2133.

2. When additive latency is enabled for IDD0, current changes by approximately 0%.

3. IPP0 test and limit is applicable for IDD0 and IDD1 conditions.

4. The IDD values must be derated (increased) when operated outside of the range 0°C ≤ TC

≤ 85°C:

When TC < 0°C: IDD2P and IDD3P must be derated by 6%; IDD4R and IDD4W must be derated

by +4%; and IDD7 must be derated by +11%.

When TC > 85°C: IDD0, IDD1, IDD2N, IDD2NT, IDD2Q, IDD3N, IDD3P, IDD4R, IDD4W, and IDD5R must

be derated by +3%; IDD2P must be derated by +40%.

5. When additive latency is enabled for IDD1, current changes by approximately +4%.

6. When additive latency is enabled for IDD2N, current changes by approximately 0%.

7. When DLL is disabled for IDD2N, current changes by approximately –23%.

8. When CAL is enabled for IDD2N, current changes by approximately –25%.

9. When gear-down is enabled for IDD2N, current changes by approximately 0%.

16Gb: x16 TwinDie Single Rank DDR4 SDRAM

Current Specifications – Limits

CCMTD-1725822587-9947

16gb_x16_1cs_TwinDie.pdf - Rev. G 06/18 EN 15 Micron Technology, Inc. reserves the right to change products or specifications without notice.