SA5.0A thru SA170CA www.vishay.com Vishay General Semiconductor TRANSZORB(R) Transient Voltage Suppressors FEATURES * Glass passivated chip junction * Available in uni-directional and bi-directional * 500 W peak pulse power capability with a 10/1000 s waveform, repetitive rate (duty cycle): 0.01 % * Excellent clamping capability DO-204AC (DO-15) * Very fast response time * Low incremental surge resistance * Solder dip 275 C max. 10 s, per JESD 22-B106 * AEC-Q101 qualified * Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 PRIMARY CHARACTERISTICS VWM 5.0 V to 170 V PPPM 500 W TYPICAL APPLICATIONS PD 3.0 W IFSM (uni-directional only) 70 A TJ max. 175 C Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, and telecommunication. MECHANICAL DATA DEVICES FOR BI-DIRECTION APPLICATIONS For bi-directional types, use CA suffix (e.g. SA5.0CA, SA170CA). Electrical characteristics apply in both directions. Case: DO-204AC, molded epoxy over passivated chip Molding compound meets UL 94 V-0 flammability rating Base P/N-E3 - RoHS compliant, commercial grade Base P/NHE3 - RoHS compliant, AEC-Q101 qualified Terminals: Matte tin plated leads, solderable per J-STD-002 and JESD 22-B102 E3 suffix meets JESD 201 class 1A whisker test, HE3 suffix meets JESD 201 class 2 whisker test Polarity: For uni-directional types the color band denotes cathode end, no marking on bi-directional types MAXIMUM RATINGS (TA = 25 C unless otherwise noted) PARAMETER Peak pulse power dissipation with a 10/1000 s waveform (1) (fig. 1) Peak pulse current with a 10/1000 s waveform (1) Power dissipation on infinite heatsink at TL = 75 C (fig. 5) Peak forward surge current 10 ms single half sine-wave uni-directional only Maximum instantaneous forward voltage at 100 A for uni-directional only Operating junction and storage temperature range (3) SYMBOL VALUE UNIT PPPM 500 W IPPM See next table A PD 3.0 W IFSM 70 A VF 3.5 V TJ, TSTG - 55 to + 175 C Notes (1) Non-repetitive current pulse, per fig. 3 and derated above T = 25 C per fig. 2 A (2) 8.3 ms single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum Revision: 16-Mar-12 Document Number: 88378 1 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SA5.0A thru SA170CA www.vishay.com Vishay General Semiconductor ELECTRICAL CHARACTERISTICS (TA = 25 C unless otherwise noted) DEVICE TYPE BREAKDOWN VOLTAGE VBR AT IT (1) (V) MIN. SA5.0A (4) MAX. TEST CURRENT IT (mA) STAND-OFF VOLTAGE VWM (V) MAXIMUM REVERSE LEAKAGE AT VWM (3) ID (A) 6.40 7.07 10 5.0 SA6.0A 6.67 7.37 10 6.0 SA6.5A 7.22 7.98 10 6.5 SA7.0A 7.78 8.60 10 7.0 SA7.5A 8.33 9.21 1.0 7.5 SA8.0A 8.89 9.83 1.0 8.0 SA8.5A 9.44 10.4 1.0 8.5 SA9.0A 10.0 11.1 1.0 9.0 SA10A 11.1 12.3 1.0 10 SA11A 12.2 13.5 1.0 11 SA12A 13.3 14.7 1.0 12 SA13A 14.4 15.9 1.0 13 SA14A 15.6 17.2 1.0 14 SA15A 16.7 18.5 1.0 15 SA16A 17.8 19.7 1.0 16 SA17A 18.9 20.9 1.0 17 SA18A 20.0 22.1 1.0 18 SA20A 22.2 24.5 1.0 20 SA22A 24.4 26.9 1.0 22 SA24A 26.7 29.5 1.0 24 SA26A 28.9 31.9 1.0 26 SA28A 31.1 34.4 1.0 28 SA30A 33.3 36.8 1.0 30 SA33A 36.7 40.6 1.0 33 SA36A 40.0 44.2 1.0 36 SA40A 44.4 49.1 1.0 40 SA43A 47.8 52.8 1.0 43 SA45A 50.0 55.3 1.0 45 SA48A 53.3 58.9 1.0 48 SA51A 56.7 62.7 1.0 51 SA54A 60.0 66.3 1.0 54 SA58A 64.4 71.2 1.0 58 SA60A 66.7 73.7 1.0 60 SA64A 71.1 78.6 1.0 64 SA70A 77.8 86.0 1.0 70 SA75A 83.3 92.1 1.0 75 SA78A 86.7 95.8 1.0 78 SA85A 94.4 104 1.0 85 SA90A 100 111 1.0 90 SA100A 111 123 1.0 100 SA110A 122 135 1.0 110 SA120A 133 147 1.0 120 SA130A 144 159 1.0 130 SA150A 167 185 1.0 150 SA160A 178 197 1.0 160 SA170A 189 209 1.0 170 Notes (1) Pulse test: t 50 ms p (2) Surge current waveform per fig. 3 and derate per fig. 2 (3) For bi-directional types with V WM of 10 V and less the ID limit is doubled (4) For the bi-directional SA5.0CA, the maximum V BR is 7.25 V (5) All terms and symbols are consistent with ANSI/EEE CA62.35 Revision: 16-Mar-12 600 600 400 150 50 25 10 5.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 MAXIMUM PEAK PULSE CURRENT IPPM (2) (A) 54.3 48.5 44.7 41.7 38.8 36.8 34.7 32.5 29.4 27.5 25.1 23.3 21.6 20.5 19.2 18.1 17.1 15.4 14.1 12.9 11.9 11 10 9.4 8.6 7.8 7.2 6.9 6.5 6.1 5.7 5.3 5.2 4.9 4.4 4.1 4 3.6 3.4 3.1 2.8 2.6 2.4 2.1 1.9 1.8 MAXIMUM CLAMPING VOLTAGE AT IPPM VC (V) MAXIMUM TEMPERATURE COEFFICENT AT VBR (%/C) 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103 113 121 126 137 146 162 177 193 209 243 259 275 5 5 5 6 7 7 8 9 10 11 12 13 14 16 17 19 20 23 25 28 30 31 36 39 41 46 50 52 56 61 65 70 71 76 85 91 95 103 110 123 133 146 158 184 196 208 Document Number: 88378 2 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SA5.0A thru SA170CA www.vishay.com Vishay General Semiconductor ORDERING INFORMATION (Example) PREFERRED PIN UNIT WEIGHT (g) PREFERRED PACKAGE CODE BASE QUANTITY DELIVERY MODE SA5.0A-E3/54 0.432 54 4000 13" diameter paper tape and reel SA5.0AHE3/54 (1) 0.432 54 4000 13" diameter paper tape and reel Note (1) AEC-Q101 qualified RATINGS AND CHARACTERISTICS CURVES (TA = 25 C unless otherwise noted) 150 Non-Repetitive Pulse Waveform shown in Fig. 3 TA = 25 C 10 Impulse Exponential Decay PPK "0.5" td 1.0 PPK IPPM - Peak Pulse Current, % IRSM PPPM - Peak Pulse Power (kW) 30 Half Sine td td = 7 tp PPK Square td Current Waveforms 0.1 0.1 s 1.0 s 10 s 100 s Peak Value IPPM 100 Half Value - IPP IPPM 2 10/1000 s Waveform as defined by R.E.A. 50 td 0 10 ms 1.0 ms 0 td - Pulse Width 1.0 2.0 3.0 4.0 t - Time (ms) Fig. 1 - Peak Pulse Power Rating Curve Fig. 3 - Pulse Waveform 100 200 IFSM - Peak Forward Surge Current (A) Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage, % TJ = 25 C Pulse Width (td) is defined as the Point where the Peak Current decays to 50 % of IPPM tr = 10 s 75 50 25 0 8.3 ms Single Half Sine-Wave 100 10 0 25 50 75 100 125 150 TJ - Initial Temperature (C) Fig. 2 - Pulse Derating Curve Revision: 16-Mar-12 175 200 1 10 100 Number of Cycles at 60 Hz Fig. 4 - Maximum Non-Repetitive Forward Surge Current Uni-Directional Only Document Number: 88378 3 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SA5.0A thru SA170CA www.vishay.com Vishay General Semiconductor 100 60 Hz Resistive or Inductive Load VC - Incremental Clamping Voltage PD - Power Dissipation (W) 4.0 3.0 2.0 L = 0.375" (9.5 mm) Lead Lengths 1.0 0 25 50 75 100 125 150 175 SA110 SA70 SA40 10 SA24 200 Fig. 8 - Incremental Clamping Voltage Curve Uni-Directional 100 10 000 VC - Incremental Clamping Voltage CJ - Capaciatnce (pF) Uni-Directional Bi-Directional TJ = 25 C f = 1.0 MHz Vsig = 50 mVp-p 100 VR = Rated Stand-Off voltage 100 Waveform: 8 x 20 Impulse DVC = VC - VBR 500 SA110 SA70 SA60 SA40 SA30 SA24 SA15 SA9.0 SA6.5 1.0 10 1 VWM - Reverse Stand-Off Voltage (V) 50 IPP - Peak Pulse Current (A) Fig. 9 - Incremental Clamping Voltage Curve Bi-Directional Fig. 6 - Capacitance 100 Waveform: 8 x 20 Impulse DVC = VC - VBR SA170 VC - Incremental Clamping Voltage 100 VC - Incremental Clamping Voltage SA170 10 0.1 0.5 10 5 50 IPP - Peak Pulse Current (A) Fig. 5 - Steady State Power Derating Curve VR = 0 10 1 TL - Lead Temperature (C) 1000 SA15 SA9.0 SA5.0 1.0 0.1 0.5 0 Waveform: 10 x 1000 Impulse DVC = VC - VBR SA170 SA110 SA70 SA54 SA40 10 SA30 SA24 SA18 SA15 SA12 SA5.0 SA9.0 1.0 0.1 0.5 1 10 50 IPP - Peak Pulse Current (A) Fig. 7 - Incremental Clamping Voltage Curve Uni-Directional Revision: 16-Mar-12 Waveform: 10 x 1000 Impulse DVC = VC - VBR SA170 SA110 SA70 10 SA40 SA24 SA15 SA9.0 1.0 0.1 0.5 SA6.5 1 10 50 IPP - Peak Pulse Current (A) Fig. 10 - Incremental Clamping Voltage Curve Bi-Directional Document Number: 88378 4 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SA5.0A thru SA170CA www.vishay.com Vishay General Semiconductor 200 V - Temperature Coefficient (mV/C) IF - Forward Current (A) 100 TJ = 25 C Pulse Width = 300 s 1 % Duty Cycle 20 10 2 1 Uni-Directional Only 0.2 0.1 100 Uni-Directional Bi-Directional 10 1.0 0 0.5 1 1.5 5.0 2.5 2 VF - Forward Voltage (V) 10 100 500 VWM - Rated Stand-Off Voltage (V) Fig. 11 - Typical Instantaneous Forward Voltage Fig. 12 - Breakdown Voltage Temperature Coefficient Curve PACKAGE OUTLINE DIMENSIONS in inches (millimeters) DO-204AC (DO-15) 0.034 (0.86) 0.028 (0.71) DIA. 1.0 (25.4) MIN. 0.300 (7.6) 0.230 (5.8) 0.140 (3.6) 0.104 (2.6) DIA. 1.0 (25.4) MIN. Revision: 16-Mar-12 Document Number: 88378 5 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Revision: 12-Mar-12 1 Document Number: 91000