0.1 GHz to 2.5 GHz 70 dB Logarithmic Detector/Controller AD8313 FEATURES FUNCTIONAL BLOCK DIAGRAM + NINE DETECTOR CELLS + + 8dB 8dB 8dB LP 8dB INLO 3 8 VOUT VI 7 VSET 6 COMM 5 PWDN INTERCEPT CONTROL AD8313 VPOS 4 SLOPE CONTROL BAND GAP REFERENCE GAIN BIAS 01085-C-001 EIGHT 8dB 3.5GHz AMPLIFIER STAGES Figure 1. When used as a log amplifier, scaling is determined by a separate feedback interface (a transconductance stage) that sets the slope to approximately 18 mV/dB; used as a controller, this stage accepts the setpoint input. The logarithmic intercept is positioned to nearly -100 dBm, and the output runs from about 0.45 V dc at -73 dBm input to 1.75 V dc at 0 dBm input. The scale and intercept are supply- and temperature-stable. The AD8313 is fabricated on Analog Devices' advanced 25 GHz silicon bipolar IC process and is available in an 8-lead MSOP package. The operating temperature range is -40C to +85C. An evaluation board is available. 2.0 5 1.8 4 1.6 3 1.4 2 1.2 1 1.0 0 0.8 -1 0.6 -2 0.4 -3 0.2 -4 0 -80 -70 -60 -50 -40 -30 INPUT AMPLITUDE (dBm) -20 -10 0 OUTPUT ERROR (dB) FREQUENCY = 1.9GHz OUTPUT VOLTAGE (V DC) The AD8313 uses a cascade of eight amplifier/limiter cells, each having a nominal gain of 8 dB and a -3 dB bandwidth of 3.5 GHz. This produces a total midband gain of 64 dB. At each amplifier output, a detector (rectifier) cell is used to convert the RF signal to baseband form; a ninth detector cell is placed directly at the input of the AD8313. The current-mode outputs of these cells are summed to generate a piecewise linear approximation to the logarithmic function. They are converted to a low impedance voltage-mode output by a transresistance stage, which also acts as a low-pass filter. IV CINT INHI 2 RF transmitter power amplifier setpoint control and level monitoring Logarithmic amplifier for RSSI measurement cellular base stations, radio link, radar The AD8313 is a complete multistage demodulating logarithmic amplifier that can accurately convert an RF signal at its differential input to an equivalent decibel-scaled value at its dc output. The AD8313 maintains a high degree of log conformance for signal frequencies from 0.1 GHz to 2.5 GHz and is useful over the range of 10 MHz to 3.5 GHz. The nominal input dynamic range is -65 dBm to 0 dBm (re: 50 ), and the sensitivity can be increased by 6 dB or more with a narrow-band input impedance matching network or a balun. Application is straightforward, requiring only a single supply of 2.7 V to 5.5 V and the addition of a suitable input and supply decoupling. Operating on a 3 V supply, its 13.7 mA consumption (for TA = 25C) is only 41 mW. A power-down feature is provided; the input is taken high to initiate a low current (20 A) sleep mode, with a threshold at half the supply voltage. + VPOS 1 APPLICATIONS GENERAL DESCRIPTION + -5 01085-C-002 Wide bandwidth: 0.1 GHz to 2.5 GHz min High dynamic range: 70 dB to 3.0 dB High accuracy: 1.0 dB over 65 dB range (@ 1.9 GHz) Fast response: 40 ns full-scale typical Controller mode with error output Scaling stable over supply and temperature Wide supply range: 2.7 V to 5.5 V Low power: 40 mW at 3 V Power-down feature: 60 mW at 3 V Complete and easy to use Figure 2. Typical Logarithmic Response and Error vs. Input Amplitude Rev. D Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.326.8703 (c) 2004 Analog Devices, Inc. All rights reserved. AD8313 TABLE OF CONTENTS Specifications..................................................................................... 3 Input Coupling ........................................................................... 16 Absolute Maximum Ratings............................................................ 6 Narrow-Band LC Matching Example at 100 MHz ................ 16 ESD Caution.................................................................................. 6 Adjusting the Log Slope............................................................. 18 Pin Configurations and Function Description............................. 7 Increasing Output Current........................................................ 19 Typical Performance Characteristics ............................................. 8 Effect of Waveform Type on Intercept..................................... 19 Circuit Description......................................................................... 11 Evaluation Board ............................................................................ 20 Interfaces.......................................................................................... 13 Schematic and Layout................................................................ 20 Power-Down Interface, PWDN................................................ 13 General Operation ..................................................................... 20 Signal Inputs, INHI, INLO ........................................................ 13 Using the AD8009 Operational Amplifier .............................. 20 Logarithmic/Error Output, VOUT .......................................... 13 Varying the Logarithmic Slope................................................. 20 Setpoint Interface, VSET............................................................ 14 Operating in Controller Mode ................................................. 20 Applications..................................................................................... 15 RF Burst Response ..................................................................... 20 Basic Connections for Log (RSSI) Mode................................. 15 Outline Dimensions ....................................................................... 24 Operating in Controller Mode ................................................. 15 Ordering Guide .......................................................................... 24 REVISION HISTORY 6/04--Data Sheet Changed from Rev. C to Rev. D Updated Evaluation Board Section .............................................. 21 2/03--Data Sheet changed from Rev. B to Rev. C TPCs and Figures Renumbered........................................Universal Edits to SPECIFICATIONS............................................................. 2 Updated ESD CAUTION ................................................................ 4 Updated OUTLINE DIMENSIONS .............................................. 7 8/99--Data Sheet changed from Rev. A to Rev. B 5/99--Data Sheet changed from Rev. 0 to Rev. A 8/98--Revision 0: Initial Version Rev. D | Page 2 of 24 AD8313 SPECIFICATIONS TA = 25C, VS = 5 V1, RL 10 k, unless otherwise noted. Table 1. Parameter SIGNAL INPUT INTERFACE Specified Frequency Range DC Common-Mode Voltage Input Bias Currents Input Impedance LOG (RSSI) MODE 100 MHz5 3 dB Dynamic Range6 Range Center 1 dB Dynamic Range Slope Intercept Min2 Conditions Max2 Unit 2.5 VPOS - 0.75 10 900||1.1 GHz V A ||pF4 65 -31.5 56 19 -88 dB dBm dB mV/dB dBm Typ 0.1 fRF < 100 MHz3 Sinusoidal, input termination configuration shown in Figure 29 Nominal conditions 53.5 17 -96 21 -80 2.7 V VS 5.5 V, -40C T +85C 3 dB Dynamic Range Range Center 1 dB Dynamic Range Slope Intercept Temperature Sensitivity 900 MHz5 3 dB Dynamic Range Range Center 1 dB Dynamic Range Slope Intercept 51 16 -99 PIN = -10 dBm Nominal conditions 60 15.5 -105 64 -31 55 19 -89 -0.022 69 -32.5 62 18 -93 22 -75 20.5 -81 dB dBm dB mV/dB dBm dB/C dB dBm dB mV/dB dBm 2.7 V VS 5.5 V, -40C T +85C 3 dB Dynamic Range Range Center 1 dB Dynamic Range Slope Intercept Temperature Sensitivity 1.9 GHz7 3 dB Dynamic Range Range Center 1 dB Dynamic Range Slope Intercept 55.5 15 -110 PIN = -10 dBm Nominal conditions 52 15 -115 68.5 -32.75 61 18 -95 -0.019 73 -36.5 62 17.5 -100 21 -80 20.5 -85 dB dBm dB mV/dB dBm dB/C dB dBm dB mV/dB dBm 2.7 V VS 5.5 V, -40C T +85C 3 dB Dynamic Range Range Center 1 dB Dynamic Range Slope Intercept Temperature Sensitivity 50 14 -125 PIN = -10 dBm Rev. D | Page 3 of 24 73 -36.5 60 17.5 -101 -0.019 21.5 -78 dB dBm dB mV/dB dBm dB/C AD8313 Parameter 2.5 GHz7 3 dB Dynamic Range Range Center 1 dB Dynamic Range Slope Intercept Conditions Nominal conditions Min2 Typ 48 66 -34 46 20 -92 16 -111 Max2 Unit 25 -72 dB dBm dB mV/dB dBm 2.7 V VS 5.5 V, -40C T +85C 3 dB Dynamic Range Range Center 1 dB Dynamic Range Slope Intercept Temperature Sensitivity 3.5 GHz5 3 dB Dynamic Range 1 dB Dynamic Range Slope Intercept CONTROL MODE Controller Sensitivity Low Frequency Gain Open-Loop Corner Frequency Open-Loop Slew Rate VSET Delay Time VOUT INTERFACE Current Drive Capability Source Current Sink Current Minimum Output Voltage Maximum Output Voltage Output Noise Spectral Density Small Signal Response Time Large Signal Response Time VSET INTERFACE Input Voltage Range Input Impedance POWER-DOWN INTERFACE PWDN Threshold Power-Up Response Time PWDN Input Bias Current 47 14.5 -128 PIN =-10 dBm Nominal conditions f = 900 MHz VSET to VOUT8 VSET to VOUT8 f = 900 MHz Open-loop Open-loop PIN = -60 dBm, fSPOT = 100 Hz PIN = -60 dBm, fSPOT = 10 MHz PIN = -60 dBm to -57 dBm, 10% to 90% PIN = No signal to 0 dBm; settled to 0.5 dB Time delay following high to low transition until device meets full specifications. PWDN = 0 V PWDN = VS dB dB mV/dB dBm 23 84 700 2.5 150 V/dB dB Hz V/s ns 400 10 50 VPOS - 0.1 2.0 1.3 40 110 A mA mV V V/Hz V/Hz ns ns VPOS V k||pF VPOS/2 1.8 V s 5 <1 A A 13.7 Rev. D | Page 4 of 24 60 160 18||1 2.7 4.5 V VS 5.5 V, -40C T +85C 2.7 V VS 3.3 V, -40C T +85C 4.5 V VS 5.5 V, -40C T +85C 2.7 V VS 3.3 V, -40C T +85C 25 -56 dB dBm dB mV/dB dBm dB/C 43 35 24 -65 0 POWER SUPPLY Operating Range Powered-Up Current Powered-Down Current 68 -34.5 46 20 -92 -0.040 50 20 5.5 15.5 18.5 18.5 150 50 V mA mA mA A A 4 AD8313 1 Except where otherwise noted; performance at VS = 3 V is equivalent to 5 V operation. Minimum and maximum specified limits on parameters that are guaranteed but not tested are 6 sigma values. 3 Input impedance shown over frequency range in Figure 26. 4 Double vertical bars (||) denote "in parallel with." 5 Linear regression calculation for error curve taken from -40 dBm to -10 dBm for all parameters. 6 Dynamic range refers to range over which the linearity error remains within the stated bound. 7 Linear regression calculation for error curve taken from -60 dBm to -5 dBm for 3 dB dynamic range. All other regressions taken from -40 dBm to -10 dBm. 8 AC response shown in Figure 12. 2 Rev. D | Page 5 of 24 AD8313 ABSOLUTE MAXIMUM RATINGS Table 2. Supply Voltage VS VOUT, VSET, PWDN Input Power Differential (re: 50 , 5.5 V) Input Power Single-Ended (re: 50 , 5.5 V) Internal Power Dissipation JA Maximum Junction Temperature Operating Temperature Range Storage Temperature Range 5.5 V 0 V, VPOS 25 dBm 19 dBm 200 mW 200C/W 125C -40C to +85C -65C to +150C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. D | Page 6 of 24 AD8313 VPOS 1 INHI 2 INLO 3 VPOS 4 AD8313 TOP VIEW (Not to Scale) 8 VOUT 7 VSET 6 COMM 5 PWDN 01085-C-003 PIN CONFIGURATIONS AND FUNCTION DESCRIPTION Figure 3. Pin Configuration Table 3. Pin Function Descriptions Pin No. 1, 4 2 3 5 6 7 8 Mnemonic VPOS INHI INLO PWDN COMM VSET VOUT Description Positive Supply Voltage (VPOS), 2.7 V to 5.5 V. Noninverting Input. This input should be ac-coupled. Inverting Input. This input should be ac-coupled. Connect Pin to Ground for Normal Operating Mode. Connect this pin to the supply for power-down mode. Device Common. Setpoint Input for Operation in Controller Mode. To operate in RSSI mode, short VSET and VOUT. Logarithmic/Error Output. Rev. D | Page 7 of 24 AD8313 TYPICAL PERFORMANCE CHARACTERISTICS 2.0 2.0 5 1.8 1.8 4 1.6 1.6 3 1.4 1.4 2 100MHz 2.5GHz 1.0 -1 +85C 0.6 0.6 900MHz 0.4 -2 0.4 -3 SLOPE AND INTERCEPT NORMALIZED AT +25C AND APPLIED TO -40C AND +85C 0.2 0 -70 -60 -50 -40 -30 -20 INPUT AMPLITUDE (dBm) -10 0 10 01085-C-004 0.2 0 -70 Figure 4. VOUT vs. Input Amplitude -60 -50 -40 -30 -20 -10 INPUT AMPLITUDE (dBm) -4 0 4 2.0 5 1.8 4 1.6 3 900MHz -40C 1.4 0 VOUT (V) 100MHz 2 900MHz -2 1.9GHz -5 10 Figure 7. VOUT and Log Conformance vs. Input Amplitude at 900 MHz for Multiple Temperatures 6 ERROR (dB) 0 +25C 0.8 0.8 1 -40C 2.5GHz 2 1.2 1 +25C 1.0 0.8 2.5GHz 100MHz 0 -1 +85C 0.6 ERROR (dB) 1.0 1.2 01-85-C-007 1.9GHz VOUT (V) VOUT (V) 1.2 ERROR (dB) TA = 25C, VS = 5 V, RL input match shown in Figure 29, unless otherwise noted. -2 1.9GHz 0.4 -50 -40 -30 -20 INPUT AMPLITUDE (dBm) 0 -10 10 0 -70 Figure 5. Log Conformance vs. Input Amplitude -50 -40 -30 -20 -10 INPUT AMPLITUDE (dBm) 0 -5 10 Figure 8. VOUT and Log Conformance vs. Input Amplitude at 1.9 GHz for Multiple Temperatures 2.0 5 2.0 5 1.8 4 1.8 4 1.6 3 1.6 2 1.4 2 1 1.2 1 1.2 +25C 1.0 0 +85C 0.8 -1 VOUT (V) -40C 1.0 0.6 -2 0.4 -3 0.4 -60 -50 -40 -30 -20 INPUT AMPLITUDE (dBm) -10 0 -5 10 Figure 6. VOUT and Log Conformance vs. Input Amplitude at 100 MHz for Multiple Temperatures 0 -70 -1 SLOPE AND INTERCEPT NORMALIZED AT +25C AND APPLIED TO -40C AND +85C -2 -3 +85C 0.2 -4 01085-C-006 0 -70 SLOPE AND INTERCEPT NORMALIZED AT +25C AND APPLIED TO -40C AND +85C 0 +25C 0.8 0.6 0.2 3 -40C ERROR (dB) 1.4 VOUT (V) -60 ERROR (dB) -60 -4 -60 -50 -4 -40 -30 -20 -10 INPUT AMPLITUDE (dBm) 0 -5 10 01085-C-009 -6 -70 01085-C-005 0.2 -3 SLOPE AND INTERCEPT NORMALIZED AT +25C AND APPLIED TO -40C AND +85C 01085-C-008 -4 Figure 9. VOUT and Log Conformance vs. Input Amplitude at 2.5 GHz for Multiple Temperatures Rev. D | Page 8 of 24 AD8313 22 -70 21 -80 INTERCEPT (dBm) SLOPE (mV/dB) +85C 20 +25C 19 -40C 18 +85C -90 +25C -100 17 500 1000 1500 FREQUENCY (MHz) 2000 2500 -110 Figure 10. VOUT Slope vs. Frequency for Multiple Temperatures 0 1000 1500 FREQUENCY (MHz) 500 2000 2500 01085-C-013 0 01085-C-010 16 -40C Figure 13. VOUT Intercept vs. Frequency for Multiple Temperatures -70 24 23 -75 SPECIFIED OPERATING RANGE SPECIFIED OPERATING RANGE 22 -80 INTERCEPT (dBm) SLOPE (mV/dB) 21 2.5GHz 20 100MHz 19 900MHz 18 1.9GHz 17 -85 100MHz -90 2.5GHz -95 900MHz 1.9GHz -100 16 3.0 3.5 4.0 4.5 5.0 SUPPLY VOLTAGE (V) 5.5 6.0 01085-C-011 14 2.5 -110 2.5 Figure 11. VOUT Slope vs. Supply Voltage 3.0 3.5 4.0 4.5 5.0 SUPPLY VOLTAGE (V) 5.5 6.0 01085-C-014 -105 15 Figure 14. VOUT Intercept vs. Supply Voltage 10 REF LEVEL = 92dB 2GHz RF INPUT SCALE: 10dB/DIV VSET TO VOUT GAIN (dB) RF INPUT -70dBm V/ Hz -60dBm -55dBm 1 -50dBm -45dBm -40dBm 1k 10k FREQUENCY (Hz) 100k 1M 0.1 100 1k 10k 100k FREQUENCY (Hz) 1M Figure 15. VOUT Noise Spectral Density Figure 12. AC Response from VSET to VOUT Rev. D | Page 9 of 24 10M 01085-C-015 100 01085-C-012 -35dBm -30dBm AD8313 100.00 CH. 1 AND CH. 2: 200mV/DIV VS = +5.5V 13.7mA CH. 1 10.00 VS = +2.7V CH. 2 PULSED RF 100MHz, -45dBm CH. 1 GND 1.00 VPOS = +3V VPOS = +5V CH. 2 GND 0.10 40A 0.01 0 1 2 3 PWDN VOLTAGE (V) 4 5 HORIZONTAL: 50ns/DIV 01085-C-016 20A Figure 18. Response Time, No Signal to -45 dBm Figure 16. Typical Supply Current vs. PWDN Voltage CH. 1 AND CH. 2: 1V/DIV 01085-C-019 SUPPLY CURRENT (mA) AVERAGE: 50 SAMPLES CH. 1 & CH. 2: 500mV/DIV CH. 3: 5V/DIV AVERAGE: 50 SAMPLES VS = +5.5V VOUT @ VS = +5.5V CH. 1 CH. 1 GND VS = +2.7V CH. 2 CH. 1 GND VOUT @ VS = +2.7V CH. 2 GND PULSED RF 100MHz, 0dBm CH. 2 GND CH. 3 GND HORIZONTAL: 1s/DIV HORIZONTAL: 50ns/DIV 01085-C-020 01085-C-017 PWDN Figure 19. Response Time, No Signal to 0 dBm Figure 17. PWDN Response Time ________________________________________________________________________________________________________________________________ 1 VPOS 0.1F 0.01F 2 INHI 0.01F TEK P6205 FET PROBE HP8648B SIGNAL GENERATOR PULSE MODULATION MODE OUT TEK TDS784C SCOPE TRIG COMM 6 4 VPOS PWDN 5 0.1F PULSE MODE IN OUT HP8112A PULSE GENERATOR TRIG OUT RF OUT 0603 SIZE SURFACE MOUNT COMPONENTS ON A LOW LEAKAGE PC BOARD 10 EXT TRIG 10MHz REF OUTPUT -6dB RF SPLITTER VSET 7 54.9 3 INLO +VS VOUT 8 AD8313 HP8112A PULSE GENERATOR -6dB 10 +VS 01085-C-018 10 +VS EXT TRIG 0.01F 0.01F Figure 20. Test Setup for PWDN Response Time +VS 1 VPOS 2 INHI VSET 7 3 INLO COMM 6 4 VPOS PWDN 5 0.1F VOUT 8 AD8313 54.9 TEK P6205 FET PROBE TEK TDS784C SCOPE TRIG 0603 SIZE SURFACE MOUNT COMPONENTS ON A LOW LEAKAGE PC BOARD 10 0.1F Figure 21. Test Setup for RSSI Mode Pulse Response Rev. D | Page 10 of 24 01085-C-021 HP8648B 10MHz REF OUTPUT SIGNAL GENERATOR PIN = 0dBm RF OUT AD8313 CIRCUIT DESCRIPTION separated by 8 dB, the overall dynamic range is about 72 dB (Figure 23). The upper end of this range is determined by the capacity of the first detector cell, and occurs at approximately 0 dBm. The practical dynamic range is over 70 dB to the 3 dB error points. However, some erosion of this range can occur at temperature and frequency extremes. Useful operation to over 3 GHz is possible, and the AD8313 remains serviceable at 10 MHz, needing only a small amount of additional ripple filtering. The AD8313 is an 8-stage logarithmic amplifier, specifically designed for use in RF measurement and power amplifier control applications at frequencies up to 2.5 GHz. A block diagram is shown in Figure 22. For a detailed description of log amp theory and design principles, refer to the AD8307 data sheet. + NINE DETECTOR CELLS + + + + IV 8 VOUT VPOS 1 2.0 CINT INHI 2 8dB 8dB 8dB LP 8dB INLO 3 5 SLOPE = 18mV/dB 1.8 VI 7 4 VSET 1.6 3 1.4 2 1.2 1 1.0 0 0.8 -1 0.6 -2 BAND GAP REFERENCE GAIN BIAS 5 PWDN Figure 22. Block Diagram -3 0.4 A fully differential design is used. Inputs INHI and INLO (Pins 2 and 3) are internally biased to approximately 0.75 V below the supply voltage, and present a low frequency impedance of nominally 900 in parallel with 1.1 pF. The noise spectral density referred to the input is 0.6 nV/Hz, equivalent to a voltage of 35 V rms in a 3.5 GHz bandwidth, or a noise power of -76 dBm re: 50 . This sets the lower limit to the dynamic range; the Applications section shows how to increase the sensitivity by using a matching network or input transformer. However, the low end accuracy of the AD8313 is enhanced by specially shaping the demodulation transfer characteristic to partially compensate for errors due to internal noise. Each of the eight cascaded stages has a nominal voltage gain of 8 dB and a bandwidth of 3.5 GHz. Each stage is supported by precision biasing cells that determine this gain and stabilize it against supply and temperature variations. Since these stages are direct-coupled and the dc gain is high, an offset compensation loop is included. The first four stages and the biasing system are powered from Pin 4, while the later stages and the output interfaces are powered from Pin 1. The biasing is controlled by a logic interface PWDN (Pin 5); this is grounded for normal operation, but may be taken high (to VS) to disable the chip. The threshold is at VPOS/2 and the biasing functions are enabled and disabled within 1.8 s. Each amplifier stage has a detector cell associated with its output. These nonlinear cells perform an absolute value (fullwave rectification) function on the differential voltages along this backbone in a transconductance fashion; their outputs are in current-mode form and are thus easily summed. A ninth detector cell is added at the input of the AD8313. Since the midrange response of each of these nine detector stages is INTERCEPT = -100dBm -4 0.2 0 -90 -80 -70 -60 -50 -40 -30 INPUT AMPLITUDE (dBm) -20 -10 0 -5 01085-c-023 SLOPE CONTROL COMM VOUT (V) VPOS 4 6 01085-C-001 INTERCEPT CONTROL AD8313 ERROR (dB) EIGHT 8dB 3.5GHz AMPLIFIER STAGES Figure 23. Typical RSSI Response and Error vs. Input Power at 1.9 GHz The fluctuating current output generated by the detector cells, with a fundamental component at twice the signal frequency, is filtered first by a low-pass section inside each cell, and then by the output stage. The output stage converts these currents to a voltage, VOUT, at VOUT (Pin 8), which can swing rail-to-rail. The filter exhibits a 2-pole response with a corner at approximately 12 MHz and full-scale rise time (10% to 90%) of 40 ns. The residual output ripple at an input frequency of 100 MHz has an amplitude of under 1 mV. The output can drive a small resistive load; it can source currents of up to 400 A, and sink up to 10 mA. The output is stable with any capacitive load, though settling time could be impaired. The low frequency incremental output impedance is approximately 0.2 . In addition to its use as an RF power measurement device (that is, as a logarithmic amplifier), the AD8313 may also be used in controller applications by breaking the feedback path from VOUT to VSET (Pin 7), which determines the slope of the output (nominally 18 mV/dB). This pin becomes the setpoint input in controller modes. In this mode, the voltage VOUT remains close to ground (typically under 50 mV) until the decibel equivalent of the voltage VSET is reached at the input, when VOUT makes a rapid transition to a voltage close to VPOS (see the Operating in Controller Mode section). The logarithmic intercept is nominally positioned at -100 dBm (re: 50 ); this is effective in both the log amp mode and the controller mode. Rev. D | Page 11 of 24 AD8313 With Pins 7 and 8 connected (log amp mode), the output can be stated as With Pins 7 and 8 disconnected (controller mode), the output can be stated as VOUT = VSLOPE ( PIN + 100 dBm) where PIN is the input power stated in dBm when the source is directly terminated in 50 . However, the input impedance of the AD8313 is much higher than 50 , and the sensitivity of this device may be increased by about 12 dB by using some type of matching network (see below), which adds a voltage gain and lowers the intercept by the same amount. Dependence on the reference impedance can be avoided by restating the expression as when V SLOPE log ( PIN / 100) > V SET VOUT 0 when V SLOPE log ( PIN / 100) < V SET when the input is stated in terms of the power of a sinusoidal signal across a net termination impedance of 50 . The transition zone between high and low states is very narrow since the output stage behaves essentially as a fast integrator. The above equations can be restated as VOUT = 20 x VSLOPE x log x (VIN / 2.2 V) where VIN is the rms value of a sinusoidal input appearing across Pins 2 and 3; here, 2.2 V corresponds to the intercept, expressed in voltage terms. For detailed information on the effect of signal waveform and metrics on the intercept positioning for a log amp, refer to the AD8307 data sheet. VOUT V S VOUT VS when VSLOPE log (VIN / 2.2 V) > VSET VOUT 0 when VSLOPE log (VIN / 2.2 V) < VSET Another use of the separate VOUT and VSET pins is in raising the load-driving current capability by including an external NPN emitter follower. More complete information about usage in these modes is provided in the Applications section. Rev. D | Page 12 of 24 AD8313 INTERFACES For high frequency use, Figure 26 shows the input impedance plotted on a Smith chart. This measured result of a typical device includes a 191 mil 50 trace and a 680 pF capacitor to ground from the INLO pin. POWER-DOWN INTERFACE, PWDN Frequency 100MHz 900MHz 1.9GHz 2.5GHz The power-down threshold is accurately centered at the midpoint of the supply as shown in Figure 24. If Pin 5 is left unconnected or tied to the supply voltage (recommended), the bias enable current is shut off, and the current drawn from the supply is predominately through a nominal 300 k chain (20 A at 3 V). When grounded, the bias system is turned on. The threshold level is accurately at VPOS/2. When operating in the device ON state, the input bias current at the PWDN pin is approximately 5 A for VPOS = 3 V. j j j j j X 400 135 65 43 100MHz AD8313 MEASURED 900MHz 2.5GHz 1.9GHz 900 1.1pF Figure 26. Typical Input Impedance 150k 150k COMM 6 01085-C-024 TO BIAS ENABLE 75k PWDN 5 Figure 24. Power-Down Threshold Circuitry SIGNAL INPUTS, INHI, INLO The simplest low frequency ac model for this interface consists of just a 900 resistance, RIN, in shunt with a 1.1 pF input capacitance, CIN, connected across INHI and INLO. Figure 25 shows these distributed in the context of a more complete schematic. The input bias voltage shown is for the enabled chip; when disabled, it rises by a few hundred millivolts. If the input is coupled via capacitors, this change may cause a low level signal transient to be introduced, having a time constant formed by these capacitors and RIN. For this reason, large coupling capacitors should be well matched. This is not necessary when using the small capacitors found in many impedance transforming networks used at high frequencies. TO STAGES 1 TO 4 VPOS 1 ~0.75V 0.5pF 2.5k 125 2.5k 125 1.25k INHI 2 TO 2ND STAGE INLO 3 1.25k GAIN BIAS BIAS FROM SETPOINT SUMMED DETECTOR OUTPUTS COMM CINT 8 VOUT LP LM 10mA MAX CL COMM Figure 27. Output Interface Circuitry Thus, for midscale RF input of about 3 mV, which is some 40 dB above the minimum detector output, this current is 160 A, and the output changes by 8 V/s. When VOUT is connected to VSET, the rise and fall times are approximately 40 ns (for RL 10 k ). 1.24V ~1.4mA ISOURCE 400A gm STAGE 6 01085-C-025 250 1 VPOS The nominal slew rate is 2.5 V/s. The HF compensation technique results in stable operation with a large capacitive load, CL, though the positive-going slew rate is then limited by ISOURCE/CL to 1 V/s for CL = 400 pF. 0.7pF (1ST DETECTOR) The rail-to-rail output interface is shown in Figure 27. VOUT can run from within about 50 mV of ground, to within about 100 mV of the supply voltage, and is short-circuit safe to either supply. However, the sourcing load current, ISOURCE, is limited to that which is provided by the PNP transistor, typically 400 A. Larger load currents can be provided by adding an external NPN transistor (see the Applications section). The dc open-loop gain of this amplifier is high, and it may be regarded as an integrator having a capacitance of 2 pF (CINT) driven by the current-mode signal generated by the summed outputs of the nine detector stages, which is scaled approximately 4.0 A/dB. 01085-C-027 50k VPOS 4 + - - - - LOGARITHMIC/ERROR OUTPUT, VOUT VPOS 4 0.5pF R 650 55 22 23 01085-C-026 This section describes the signal and control interfaces and their behavior. On-chip resistances and capacitances exhibit variations of up to 20%. These resistances are sometimes temperature-dependent, and the capacitances may be voltagedependent. Figure 25. Input Interface Simplified Schematic Rev. D | Page 13 of 24 AD8313 SETPOINT INTERFACE, VSET VPOS 1 25A FDBK TO O/P STAGE 25A R1 12k LP VSET 8 R2 6k R3 1.5k COMM 6 Figure 28. Setpoint Interface Circuitry Rev. D | Page 14 of 24 01085-C-028 The setpoint interface is shown in Figure 28. The voltage, VSET, is divided by a factor of 3 in a resistive attenuator of 18 k total resistance. The signal is converted to a current by the action of the op amp and the resistor R3 (1.5 k), which balances the current generated by the summed output of the nine detector cells at the input to the previous cell. The logarithmic slope is nominally 3 s x 4.0 A/dB x 1.5 k = 18 mV/dB. AD8313 APPLICATIONS BASIC CONNECTIONS FOR LOG (RSSI) MODE OPERATING IN CONTROLLER MODE Figure 29 shows the AD8313 connected in its basic measurement mode. A power supply between 2.7 V and 5.5 V is required. The power supply to each of the VPOS pins should be decoupled with a 0.1 F surface-mount ceramic capacitor and a 10 series resistor. Figure 30 shows the basic connections for operation in controller mode. The link between VOUT and VSET is broken and a setpoint is applied to VSET. Any difference between VSET and the equivalent input power to the AD8313 drives VOUT either to the supply rail or close to ground. If VSET is greater than the equivalent input power, VOUT is driven toward ground, and vice versa. As stated in the Absolute Maximum Ratings table, an externally applied overvoltage on the VOUT pin, which is outside the range 0 V to VPOS, is sufficient to cause permanent damage to the device. If overvoltages are expected on the VOUT pin, a series resistor, RPROT, should be included as shown. A 500 resistor is sufficient to protect against overvoltage up to 5 V; 1000 should be used if an overvoltage of up to 15 V is expected. Since the output stage is meant to drive loads of no more than 400 A, this resistor does not impact device performance for higher impedance drive applications (higher output current applications are discussed in the Increasing Output Current section). R1 10 680pF VPOS VOUT 8 2 INHI VSET 7 3 INLO COMM 6 4 VPOS PWDN 5 AD8313 1 VPOS VOUT 8 2 INHI VSET 7 3 INLO COMM 6 4 VPOS PWDN 5 0.1F RPROT AD8313 R3 10 0.1F Figure 30. Basic Connections for Operation in the Controller Mode This mode of operation is useful in applications where the output power of an RF power amplifier (PA) is to be controlled by an analog AGC loop (Figure 31). In this mode, a setpoint voltage, proportional in dB to the desired output power, is applied to the VSET pin. A sample of the output power from the PA, via a directional coupler or other means, is fed to the input of the AD8313. ENVELOPE OF TRANSMITTED SIGNAL POWER AMPLIFIER RF IN DIRECTIONAL COUPLER AD8313 VOUT RFIN VSET SETPOINT CONTROL DAC RPROT RL = 1M Figure 31. Setpoint Controller Operation 53.6 680pF +VS 1 0.1F R2 10 0.1F Figure 29. Basic Connections for Log (RSSI) Mode 01085-C-029 +VS +VS R1 10 01085-C-031 VSET is connected to VOUT to establish a feedback path that controls the overall scaling of the logarithmic amplifier. The load resistance, RL, should not be lower than 5 k so that the full-scale output of 1.75 V can be generated with the limited available current of 400 A max. +VS 01085-C-030 The PWDN pin is shown as grounded. The AD8313 may be disabled by a logic high at this pin. When disabled, the chip current is reduced to about 20 A from its normal value of 13.7 mA. The logic threshold is at VPOS/2, and the enable function occurs in about 1.8 s. However, that additional settling time is generally needed at low input levels. While the input in this case is terminated with a simple 50 broadband resistive match, there are many ways in which the input termination can be accomplished. These are discussed in the Input Coupling section. VOUT is applied to the gain control terminal of the power amplifier. The gain control transfer function of the power amplifier should be an inverse relationship, that is, increasing voltage decreases gain. A positive input step on VSET (indicating a demand for increased power from the PA) drives VOUT toward ground. This should be arranged to increase the gain of the PA. The loop settles when VOUT settles to a voltage that sets the input power to the AD8313 to the dB equivalent of VSET. Rev. D | Page 15 of 24 AD8313 INPUT COUPLING 3 BALANCED The signal can be coupled to the AD8313 in a variety of ways. In all cases, there must not be a dc path from the input pins to ground. Some of the possibilities include dual-input coupling capacitors, a flux-linked transformer, a printed circuit balun, direct drive from a directional coupler, or a narrow-band impedance matching network. 2 MATCHED TERMINATED DR = 66dB 0 BALANCED DR = 71dB -1 Figure 32 shows a simple broadband resistive match. A termination resistor of 53.6 combines with the internal input impedance of the AD8313 to give an overall resistive input impedance of approximately 50 . It is preferable to place the termination resistor directly across the input pins, INHI to INLO, where it lowers the possible deleterious effects of dc offset voltages on the low end of the dynamic range. At low frequencies, this may not be quite as beneficial, since it requires larger coupling capacitors. The two 680 pF input coupling capacitors set the high-pass corner frequency of the network at 9.4 MHz. MATCHED DR = 69dB -2 -3 -90 -80 -70 -60 -50 -40 -30 -20 INPUT AMPLITUDE (dBm) -10 0 10 01085-C-033 ERROR (dB) 1 Figure 33. Comparison of Terminated, Matched, and Balanced Input Drive at 900 MHz 3 TERMINATED DR = 75dB 2 AD8313 MATCHED C2 680pF RMATCH 53.6 CIN ERROR (dB) 1 RIN The high-pass corner frequency can be set higher according to the equation BALANCED MATCHED DR = 73dB BALANCED DR = 75dB -2 -3 -90 1 = 2 x x C x 50 -80 -70 -60 -50 -40 -30 -20 INPUT AMPLITUDE (dBm) -10 0 10 Figure 34. Comparison of Terminated, Matched, and Balanced Input Drive at 1.9 GHz where: NARROW-BAND LC MATCHING EXAMPLE AT 100 MHz C1 x C2 C= C1 x C2 In high frequency applications, the use of a transformer, balun, or matching network is advantageous. The impedance matching characteristics of these networks provide what is essentially a gain stage before the AD8313 that increases the device sensitivity. This gain effect is explored in the following matching example. Figure 33 and Figure 34 show device performance under these three input conditions at 900 MHz and 1.9 GHz. While the 900 MHz case clearly shows the effect of input matching by realigning the intercept as expected, little improvement is seen at 1.9 GHz. Clearly, if no improvement in sensitivity is required, a simple 50 termination may be the best choice for a given design based on ease of use and cost of components. 0 -1 Figure 32. A Simple Broadband Resistive Input Termination f 3 dB TERMINATED 01085-C-034 C1 680pF 01085-C-032 50 SOURCE 50 While numerous software programs provide an easy way to calculate the values of matching components, a clear understanding of the calculations involved is valuable. A low frequency (100 MHz) value has been used for this example because of the deleterious board effects at higher frequencies. RF layout simulation software is useful when board design at higher frequencies is required. A narrow-band LC match can be implemented either as a series-inductance/shunt-capacitance or as a series-capacitance/ shunt-inductance. However, the concurrent requirement that the AD8313 inputs, INHI and INLO, be ac-coupled, makes a series-capacitance/shunt-inductance type match more appropriate (Figure 35). Rev. D | Page 16 of 24 AD8313 50 SOURCE 50 Solving for L1 gives AD8313 C1 LMATCH CIN L1 = RIN 01085-C-035 C2 Typically, the AD8313 needs to be matched to 50 . The input impedance of the AD8313 at 100 MHz can be read from the Smith chart (Figure 26) and corresponds to a resistive input impedance of 900 in parallel with a capacitance of 1.1 pF. To make the matching process simpler, the AD8313 input capacitance, CIN, can be temporarily removed from the calculation by adding a virtual shunt inductor (L2), which resonates away CIN (Figure 36). This inductor is factored back into the calculation later. This allows the main calculation to be based on a simple resistive-to-resistive match, that is, 50 to 900 . The resonant frequency is defined by the equation 1 L2 x C IN 1 2 C IN = 2.3 H 50 SOURCE 50 AD8313 C1 L1 L2 (C1 x C2) (C1 + C2) (C1 x C2) LMATCH = (C1 + C2) CMATCH = CIN L MATCH = L1 x L2 = 294 nH L1 + L2 C1 and C2 can be chosen in a number of ways. First, C2 can be set to a large value, for example, 1000 pF, so that it appears as an RF short. C1 would then be set equal to the calculated value of CMATCH. Alternatively, C1 and C2 can each be set to twice CMATCH so that the total series capacitance is equal to CMATCH. By making C1 and C2 slightly unequal (that is, select C2 to be about 10% less than C1) but keeping their series value the same, the amplitude of the signals on INHI and INLO can be equalized so that the AD8313 is driven in a more balanced manner. Any of the options detailed above can be used provided that the combined series value of C1 and C2, that is, C1 x C2/(C1 + C2) is equal to CMATCH. Assuming a lossless matching network and noting conservation of power, the impedance transformation from RS to RIN (50 to 900 ) has an associated voltage gain given by RIN 01085-C-036 C2 = 337.6 nH In all cases, the values of CMATCH and LMATCH must be chosen from standard values. At this point, these values need now be installed on the board and measured for performance at 100 MHz. Because of board and layout parasitics, the component values from the preceding example had to be tuned to the final values of CMATCH = 8.9 pF and LMATCH = 270 nH as shown in Table 4. therefore, L2 = 2f 0 Because L1 and L2 are parallel, they can be combined to give the final value for LMATCH, that is, Figure 35. Narrow-Band Reactive Match = RS RIN TEMPORARY INDUCTANCE Gain dB = 20 x log RIN = 12.6 dB RS Figure 36. Input Matching Example With CIN and L2 temporarily out of the picture, the focus is now on matching a 50 source resistance to a (purely resistive) load of 900 and calculating values for CMATCH and L1. When RS RIN = L1 C MATCH the input looks purely resistive at a frequency given by f0 = 1 2 L1 x C MATCH = 100 MHz Solving for CMATCH gives C MATCH = 1 RS R IN x 1 = 7.5 pF 2f 0 Because the AD8313 input responds to voltage and not to true power, the voltage gain of the matching network increases the effective input low-end power sensitivity by this amount. Thus, in this case, the dynamic range is shifted downward, that is, the 12.6 dB voltage gain shifts the 0 dBm to -65 dBm input range downward to -12.6 dBm to -77.6 dBm. However, because of network losses, this gain is not be fully realized in practice. Refer to Figure 33 and Figure 34 for an example of practical attainable voltage gains. Table 4 shows recommended values for the inductor and capacitors in Figure 35 for some selected RF frequencies in addition to the associated theoretical voltage gain. These values for a reactive match are optimal for the board layout detailed as Figure 45. Rev. D | Page 17 of 24 AD8313 Table 4. Recommended Values for C1, C2, and LMATCH in Figure 35 CMATCH (pF) 8.9 C1 (pF) 22 900 1.5 1900 1.5 2500 Large 3 1.5 3 1.5 390 C2 (pF) 15 1000 3 1000 3 1000 390 LMATCH (nH) 270 270 8.2 8.2 2.2 2.2 2.2 9.0 6.2 18-30mV/dB AD8313 2 INHI VSET 7 3 INLO COMM 6 4 VPOS PWDN 5 R2 10k 0.1F Figure 38. Adjusting the Log Slope As stated, the unadjusted log slope varies with frequency from 17 mV/dB to 20 mV/dB, as shown in Figure 10. By placing a resistor between VOUT and VSET, the slope can be adjusted to a convenient 20 mV/dB as shown in Figure 39. Table 5 shows the recommended values for this resistor, REXT. Also shown are values for REXT, which increase the slope to approximately 50 mV/dB. The corresponding voltage swings for a -65 dBm to 0 dBm input range are also shown in Table 6. 3.2 Figure 37 shows the voltage response of the 100 MHz matching network. Note the high attenuation at lower frequencies typical of a high-pass network. +VS R1 10 1 0.1F 15 +VS 10 VOLTAGE GAIN (dB) VPOS VOUT 8 R3 10 +VS Voltage Gain(dB) 12.6 1 0.1F VPOS VOUT 8 AD8313 20mV/dB REXT 2 INHI VSET 7 3 INLO COMM 6 4 VPOS PWDN 5 R3 10 0.1F 01085-C-039 Freq. (MHz) 100 R1 10 +VS 01085-C-038 As previously discussed, a modification of the board layout produces networks that may not perform as specified. At 2.5 GHz, a shunt inductor is sufficient to achieve proper matching. Consequently, C1 and C2 are set sufficiently high that they appear as RF shorts. Figure 39. Adjusting the Log Slope to a Fixed Value 5 Table 5. Values for REXT in Figure 39 -5 50 01085-C-037 0 100 FREQUENCY (MHz) 200 Figure 37. Voltage Response of 100 MHz Narrow-Band Matching Network ADJUSTING THE LOG SLOPE Figure 38 shows how the log slope can be adjusted to an exact value. The idea is simple: the output at the VOUT pin is attenuated by the variable resistor R2 working against the internal 18 k of input resistance at the VSET pin. When R2 is 0, the attenuation it introduces is 0, and thus the slope is the basic 18 mV/dB. Note that this value varies with frequency, (Figure 10). When R2 is set to its maximum value of 10 k, the attenuation from VOUT to VSET is the ratio 18/(18 + 10), and the slope is raised to (28/18) x 18 mV, or 28 mV/dB. At about the midpoint, the nominal scale is 23 mV/dB. Thus, a 70 dB input range changes the output by 70 x 23 mV, or 1.6 V. Frequency MHz 100 900 1900 2500 100 900 1900 2500 REXT kV 0.953 2.00 2.55 0 29.4 32.4 33.2 26.7 Slope mV/dB 20 20 20 20 50 50.4 49.8 49.7 VOUT Swing for Pin -65 dBm to 0 dBm - V 0.44 to 1.74 0.58 to 1.88 0.70 to 2.00 0.54 to 1.84 1.10 to 4.35 1.46 to 4.74 1.74 to 4.98 1.34 to 4.57 The value for REXT is calculated by REXT = (New Slope - Original Slope) x 18 k Original Slope The value for the Original Slope, at a particular frequency, can be read from Figure 10. The resulting output swing is calculated by simply inserting the New Slope value and the intercept at that frequency (Figure 10 and Figure 13) into the general equation for the AD8313's output voltage: VOUT = Slope(PIN - Intercept) Rev. D | Page 18 of 24 AD8313 INCREASING OUTPUT CURRENT EFFECT OF WAVEFORM TYPE ON INTERCEPT To drive a more substantial load, either a pull-up resistor or an emitter-follower can be used. Although specified for input levels in dBm (dB relative to 1 mW), the AD8313 responds to voltage and not to power. A direct consequence of this characteristic is that input signals of equal rms power but differing crest factors produce different results at the log amp's output. In Figure 40, a 1 k pull-up resistor is added at the output, which provides the load current necessary to drive a 1 k load to 1.7 V for VS = 2.7 V. The pull-up resistor slightly lowers the intercept and the slope. As a result, the transfer function of the AD8313 is shifted upward (intercept shifts downward). +VS 1 VPOS 0.1F VOUT 8 AD8313 2 INHI 3 INLO +VS 20mV/dB RL = 1k VSET 7 COMM 6 R3 10 01085-C-040 +VS 1k R1 10 4 VPOS PWDN 5 0.1F Figure 40. Increasing AD8313 Output Current Capability In Figure 41, an emitter-follower provides the current gain, when a 100 load can readily be driven to full-scale output. While a high transistor such as the BC848BLT1 (min = 200) is recommended, a 2 k pull-up resistor between VOUT and +VS can provide additional base current to the transistor. MIN = 200 1 0.1F VPOS VOUT 8 AD8313 2 INHI VSET 7 3 INLO COMM 6 4 VPOS PWDN 5 BC848BLT1 13k OUTPUT 10k +VS Table 6 shows the correction factors that should be applied to measure the rms signal strength of a various signal types. A continuous wave input is used as a reference. To measure the rms power of a square wave, for example, the mV equivalent of the dB value given in the table (18 mV/dB x 3.01 dB) should be subtracted from the output voltage of the AD8313. Table 6. Shift in AD8313 Output for Signals with Differing Crest Factors +VS R1 10 RL 100 R3 10 0.1F 01085-C-041 +VS Different signal waveforms vary the effective value of the log amp's intercept upward or downward. Graphically, this looks like a vertical shift in the log amp's transfer function. The device's logarithmic slope, however, is in principle not affected. For example, if the AD8313 is being fed alternately from a continuous wave and from a single CDMA channel of the same rms power, the AD8313 output voltage differs by the equivalent of 3.55 dB (64 mV) over the complete dynamic range of the device (the output for a CDMA input being lower). Figure 41. Output Current Drive Boost Connection Signal Type CW Sine Wave Square Wave or DC Triangular Wave GSM Channel (All Time Slots On) CDMA Channel PDC Channel (All Time Slots On) Gaussian Noise In addition to providing current gain, the resistor/potentiometer combination between VSET and the emitter of the transistor increases the log slope to as much as 45 mV/dB, at maximum resistance. This gives an output voltage of 4 V for a 0 dBm input. If no increase in the log slope is required, VSET can be connected directly to the emitter of the transistor. Rev. D | Page 19 of 24 Correction Factor (Add to Output Reading) 0 dB -3.01 dB +0.9 dB +0.55 dB +3.55 dB +0.58 dB +2.51 dB AD8313 EVALUATION BOARD SCHEMATIC AND LAYOUT Figure 44 shows the schematic of the AD8313 evaluation board. Note that uninstalled components are indicated as open. This board contains the AD8313 as well as the AD8009 currentfeedback operational amplifier. The evaluation board comes with the AD8313 configured to operate in RSSI/measurement mode. This mode is set by the 0 resistor (R11), which shorts the VOUT and VSET pins to each other. When using the AD8009, the AD8313 logarithmic output appears on the SMA connector labeled VOUT. Using only the AD8313, the log output can be measured at TP1 or the SMA connector labeled VSET. This is a 4-layer board (top and bottom signal layers, ground, and power). The top layer silkscreen and layout are shown in Figure 42 and Figure 43. A detailed drawing of the recommended PCB footprint for the MSOP package and the pads for the matching components are shown in Figure 45. USING THE AD8009 OPERATIONAL AMPLIFIER The vacant portions of the signal and power layers are filled out with ground plane for general noise suppression. To ensure a low impedance connection between the planes, there are multiple through-hole connections to the RF ground plane. While the ground planes on the power and signal planes are used as general-purpose ground returns, any RF grounds related to the input matching network (for example, C2) are returned directly to the RF internal ground plane. The AD8009 alleviates both of these issues. It is an ultrahigh speed current feedback amplifier capable of delivering over 175 mA of load current, with a slew rate of 5,500 V/s, which results in a rise time of 545 ps, making it ideal as a pulse amplifier. GENERAL OPERATION The AD8313 should be powered by a single supply in the range of 2.7 V to 5.5 V. The power supply to each AD8313 VPOS pin is decoupled by a 10 resistor and a 0.1 F capacitor. The AD8009 can run on either single or dual supplies, +5 V to 6 V. Both the positive and negative supply traces are decoupled using a 0.1 F capacitor. Pads are provided for a series resistor or inductor to provide additional supply filtering. The two signal inputs are ac-coupled using 680 pF high quality RF capacitors (C1, C2). A 53.6 resistor across the differential signal inputs (INHI, INLO) combines with the internal 900 input impedance to give a broadband input impedance of 50.6 . This termination is not optimal from a noise perspective due to the Johnson noise of the 53.6 resistor. Neither does it account for the AD8313's reactive input impedance nor for the decrease over frequency of the resistive component of the input impedance. However, it does allow evaluation of the AD8313 over its complete frequency range without having to design multiple matching networks. For optimum performance, a narrow-band match can be implemented by replacing the 53.6 resistor (labeled L/R) with an RF inductor and replacing the 680 pF capacitors with appropriate values. The Narrow-Band LC Matching Example at 100 MHz section includes a table of recommended values for selected frequencies and explains the method of calculation. Switch 1 is used to select between power-up and power-down modes. Connecting the PWDN pin to ground enables normal operation of the AD8313. In the opposite position, the PWDN pin can be driven externally (SMA connector labeled ENBL) to either device state, or it can be allowed to float to a disabled device state. The AD8313 can supply only 400 A at VOUT. It is also sensitive to capacitive loading, which can cause inaccurate measurements, especially in applications where the AD8313 is used to measure the envelope of RF bursts. The AD8009 is configured as a buffer amplifier with a gain of 1. Other gain options can be implemented by installing the appropriate resistors at R10 and R12. Various output filtering and loading options are available using R5, R6, and C6. Note that some capacitive loads may cause the AD8009 to become unstable. It is recommended that a 42.2 resistor be installed at R5 when driving a capacitive load. More details can be found in the AD8009 data sheet. VARYING THE LOGARITHMIC SLOPE The slope of the AD8313 can be increased from its nominal value of 18 mV/dB to a maximum of 40 mV/dB by removing R11, the 0 resistor, which shorts VSET to VOUT. VSET and VOUT are now connected through the 20 k potentiometer. The AD8009 must be configured for a gain of 1 to accurately vary the slope of the AD8313. OPERATING IN CONTROLLER MODE To put the AD8313 into controller mode, R7 and R11 should be removed, breaking the link between VOUT and VSET. The VSET pin can then be driven externally via the SMA connector labeled VSET. RF BURST RESPONSE The VOUT pin of the AD8313 is very sensitive to capacitive loading, as a result care must be taken when measuring the device's response to RF bursts. For best possible response time measurements it is recommended that the AD8009 be used to buffer the output from the AD8313. No connection should be made to TP1, the added load will effect the response time. Rev. D | Page 20 of 24 01085-C-049 001085-C-048 AD8313 Figure 43. Signal Layer Silkscreen Figure 42. Layout of Signal Layer Rev. D | Page 21 of 24 AD8313 VNEG C7 0.1F R4 0 R12 301 Z1 VPS1 Z2 C1 680pF C3 0.1F INHI 1 VOUT 8 R2 10 AD8009 R11 0 AD8313 VSET 7 3 INLO COMM 6 4 VPOS PWDN 5 C5 0.1F R3 0 L/R 53.6 INLO R9 0 VPOS INHI 2 C2 680pF C4 0.1F R7 0 VOUT R6 OPEN C6 OPEN R8 20k EXT VSET VPS2 R2 10 VPS1 R5 0 TP1 EXT ENABLE SW1 B 01085-C-046 R1 10 R10 OPEN A Figure 44. Evaluation Board Schematic Table 7. Evaluation Board Configuration Options Component VPS1, VPS2, GND, VNEG Z1 Z1 SW1 R7, R8 L/R, C1, C2, R9 R10, R12 R5, R6, C6 R1, R2, R3, R4, C3, C4, C5, C7 Function Supply Pins. VPS1 is the positive supply pin for the AD8313. VPS2 and VNEG are the positive and negative supply pins for the AD8009. If the AD8009 is being operated from a single supply, VNEG should be connected to GND. VPS1 and VPS2 are independent. GND is shared by both devices. AD8313 Logarithmic Amplifier. If the AD8313 is used in measurement mode, it is not necessary to power up the AD8009 op amp. The log output can be measured at TP1 or at the SMA connector labeled VSET. AD8009 Operational Amplifier. Device Enable. When in Position A, the PWDN pin is connected to ground and the AD8313 is in normal operating mode. In Position B, the PWDN pin is connected to an SMA connector labeled ENBL. A signal can be applied to this connector. Slope Adjust. The slope of the AD8313 can be increased from its nominal value of 18 mV/dB to a maximum of 40 mV/dB by removing R11, the 0 resistor, which shorts VSET to VOUT, and installing a 0 resistor at R7. The 20 k potentiometer at R8 can then be used to change the slope. Operating in Controller Mode. To put the AD8313 into controller mode, R7 and R11 should be removed, breaking the link between VOUT and VSET. The VSET pin can then be driven externally via the SMA connector labeled VSET. Input Interface. The 52.3 resistor in position L/R, along with C1 and C2, create a wideband 50 input. Alternatively, the 52.3 resistor can be replaced by an inductor to form an input matching network. See Input Coupling section for more details. Remove the 0 resistor at R9 for differential drive applications. Op Amp Gain Adjust. The AD8009 is initially configured as a buffer; gain = 1. To increase the gain of the op amp, modify the resistor values R10 and R12. Op Amp Output Loading/Filtering. A variety of loading and filtering options are available for the AD8009. The robust output of the op amp is capable of driving low impedances such as 50 or 75 , configure R5 and R6 accordingly. See the AD8009 data sheet for more details. Supply Decoupling. Rev. D | Page 22 of 24 Default Not Applicable Installed Installed SW1 = A R7 = 0 (Size 0603) R8 = installed L/R = 53.6 (Size 0603) C1 = C2 = 680 pF (Size 0603) R9 = 0 (Size 0603) R10 = open (Size 0603) R12 = 301 (Size 0603) R5 = 0 (Size 0603) R6 = open (Size 0603) C6 = open (Size 0603) R1 = R2 = 10 (Size 0603) R3 = R4 = 0 (Size 0603) C3 = C4 = 0.1 F (Size 0603) C5 = C7 = 0.1 F (Size 0603) AD8313 NOT CRITICAL DIMENSIONS 35 TRACE WIDTH 15.4 48 54.4 90.6 50 16 28 41 22 75 20 10 19 UNIT = MILS 50 20 27.5 51 91.3 48 126 51.7 01085-C-047 46 Figure 45. Detail of PCB Footprint for Package and Pads for Matching Network Rev. D | Page 23 of 24 AD8313 OUTLINE DIMENSIONS 3.00 BSC 8 5 4.90 BSC 3.00 BSC 4 PIN 1 0.65 BSC 1.10 MAX 0.15 0.00 0.38 0.22 COPLANARITY 0.10 0.23 0.08 8 0 0.80 0.60 0.40 SEATING PLANE COMPLIANT TO JEDEC STANDARDS MO-187AA Figure 46 . 8-Lead MicroSOIC Package [MSOP] (RM-08) Dimensions shown in millimeters and (inches) ORDERING GUIDE Model AD8313ARM AD8313ARM-REEL AD8313ARM-REEL7 AD8313ARMZ1 AD8313ARMZ-REEL71 AD8313-EVAL 1 Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C Package Descriptions 8-Lead MSOP 13" Tape and Reel 7" Tape and Reel 8-Lead MSOP 7" Tape and Reel Evaluation Board Z = Pb-free part. (c) 2004 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C01085-0-6/04(D) Rev. D | Page 24 of 24 Package Option RM-08 RM-08 RM-08 Branding J1A J1A J1A