Ordering number:ENN1410B Monolithic Digital IC LB1403N Series 5-Dot Red/Green LED Level Meter Use Package Dimensions * AC level meters such as VU meters. * DC level meters such as signal meters. unit:mm 3017D-SIP9 [LB1403N Series] Features and Functions 22.0 0.5 9 1.3 3.2 2.54 (4.5) 1 (0.84) 5.7 max 3.0 0.51 min * Capable of generating a bar-display for input voltage with 5 LEDs. * Operates from either AC or DC input voltage because of on-chip rectifier amplifier. * Lighting levels remain stable to line regulation because of on-chip voltage reference. * LEDs are driven by a constant current ; stable to line regulation. * Power supply voltage range is wide (3.5 to 16V), for a wide range of applications. * Five types of ICs constitute the series with various lighting levels of the LEDs and driving currents. * SIP-9 pin package and fewer externally connected components resuit in smaller space requirements on the circuit board. * Low noise at LED lighted mode. 0.25 1.35 SANYO : SIP9 LB1403N Series Type No. VC3 lighting sensitivity LB1403N 85 mVrms typ LB1413N 105 mVrms typ LB1423N 85 mVrms typ LB1433N 105 mVrms typ LB1443N 85 mVrms typ Comparator level Constant LED current +6dB, +3dB 0dB, -5dB, -10dB 15 mA typ 1.67Vc3, 1.33Vc3, Vc3, 0.67Vc3, 0.33Vc3 15 mA typ +6dB, +3dB, 0dB, -5dB, -10dB 1.67Vc3, 1.33Vc3, Vc3, 0.67Vc3, 0.33Vc3 +6dB, +3dB, 0dB, -6dB, -12dB 7 mA typ 7 mA typ 15 mA typ Equivalent Circuit Block Diagram and Pin Assignment Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges,or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co.,Ltd. Semiconductor Company TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN 22801TN (KT)/7227KI/8225MW/2284KI No.1410-1/4 LB1403N, 1413N, 1423N, 1433N, 1443N Specifications Absolute Maximum Ratings [LB1403N, 1413N, 1423N, 1433N, 1443N] at Ta = 25C Parameter Maximum supply voltage Allowable power dissipation Symbol Conditions Ratings VCC max Unit 18 Pd max 1100 V mW Operating temperature Topr -25 to +75 C Storage temperature Tstg -55 to +125 C Allowable Operating Ranges [LB1403N, 1413N, 1423N, 1433N, 1443N] at Ta = 25C Parameter Supply voltage Symbol Conditions VCC Ratings min typ 3.5 Unit max 6 16 V Electrical Characteristics [LB1403N] at Ta = 25C, VCC=6V, f=1kHz Parameter Current drain Symbol Conditions Ratings min typ Sensitivity ICC VIN Comparator level 1 Comparator level 2 Comparator level 3 Vc3 Comparator level 4 Vc4 2.5 3 3.5 Comparator level 5 Vc5 5 6 7 dB LED constant current ILED IINO 11 15 18.5 mA -1.0 -0.3 Input bias current VIN=0 Unit max 5 Vc3 on-level 8 mA 74 85 Vc1 -11.5 -10 -8.5 dB Vc2 -6 -5 -4 dB Point of adjustment 96 mVrms 0 dB dB A Electrical Characteristics [LB1413N] at Ta = 25C, VCC=6V, f=1kHz Parameter Current drain Symbol Sensitivity ICC VIN Comparator level 1 Vc1 Comparator level 2 Vc2 Comparator level 3 Vc3 Conditions Ratings min typ VIN=0 5 Vc3 on-level Unit max 8 mA 91 105 119 mVrms 0.28 * Vc3 0.59 * Vc3 0.33 * Vc3 0.67 * Vc3 0.40 mVrms * Vc3 0.75 mVrms * Vc3 1.25 * Vc3 1.48 * Vc3 VIN 1.33 * Vc3 1.67 * Vc3 1.42 mVrms * Vc3 1.87 mVrms * Vc3 Point of adjustment Comparator level 4 Vc4 Comparator level 5 Vc5 LED constant current ILED 11 15 Input bias current IINO -1.0 -0.3 mVrms 18.5 mA A Electrical Characteristics [LB1423N] at Ta = 25C, VCC=6V, f=1kHz Parameter Current drain Symbol Conditions Ratings min typ Sensitivity ICC VIN Comparator level 1 Comparator level 2 Comparator level 3 Vc3 Comparator level 4 Vc4 2.5 3 3.5 Comparator level 5 Vc5 5 6 7 dB LED constant current ILED IINO 5 7 9.5 mA -1.0 -0.3 Input bias current VIN=0 Unit max Vc3 on-level 5 8 mA 74 85 Vc1 -11.5 -10 -8.5 dB Vc2 -6 -5 -4 dB Point of adjustment 96 mVrms 0 dB dB A No.1410-2/4 LB1403N, 1413N, 1423N, 1433N, 1443N Electrical Characteristics [LB1433N] at Ta = 25C, VCC=6V, f=1kHz Parameter Current drain Symbol Conditions Ratings min typ VIN=0 Sensitivity ICC VIN 5 Comparator level 1 Vc1 Comparator level 2 Vc2 Comparator level 3 Vc3 Comparator level 4 Vc4 Comparator level 5 Vc5 LED constant current ILED 5 7 Input bias current IINO -1.0 -0.3 Vc3 on-level Unit max 8 mA 91 105 119 mVrms 0.28 * Vc3 0.59 * Vc3 0.33 * Vc3 0.67 * Vc3 0.40 mVrms * Vc3 0.75 mVrms * Vc3 1.25 * Vc3 1.48 * Vc3 VIN 1.33 * Vc3 1.67 * Vc3 1.42 mVrms * Vc3 1.87 mVrms * Vc3 Point of adjustment mVrms 9.5 mA A Electrical Characteristics [LB1443N] at Ta = 25C, VCC=6V, f=1kHz Parameter Current drain Symbol Conditions Ratings min typ Sensitivity ICC VIN Comparator level 1 Comparator level 2 Comparator level 3 Vc3 Comparator level 4 Vc4 2.5 3 3.5 Comparator level 5 Vc5 5 6 7 dB LED constant current ILED IINO 11 15 18.5 mA -1.0 -0.3 Input bias current VIN=0 Unit max Vc3 on-level 5 8 mA 74 85 Vc1 -14 -12 -10 dB Vc2 -7 -6 -5 dB Point of adjustment 96 mVrms 0 dB dB A Sample Application Circuit and Test Circuit (AC input VU meter) * Capacitor to be omitted when used as a DC-input signal meter. No.1410-3/4 LB1403N, 1413N, 1423N, 1433N, 1443N * C1, R1 time constant : The response time can be varied by varying the C1, R1 time constant (mainly the C1 value). When the C1, R1 time constant is larger : .................. The response time (attack time and release time) is made slower. When the C1, R1 time constant is smaller : .................. The response time (attack time and release time) is made faster. * Considerations relative to Pd max of the package : Due to the constant current ILED, most of the power consumed by the circuits is consumed within the IC. When lighting the five LEDs continuously for a prolonged length of time, make sure that VCC does not exceed : LB1403N, 1413N, 1443N VCC=9V LB1423N, 1433N VCC=14V When using a higher power supply voltage, insert a resistor in series with the LEDs to restrain the power consumed within the IC package. For LB1403N, 1413N, 1443N : For LB1423N, 1433N Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be expor ted without obtaining the expor t license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of February, 2001. Specifications and information herein are subject to change without notice. PS No.1410-4/4