HDSP-315x/316x/515x/516x Series 10 mm and 13 mm Slim Font Seven Segment Displays Data Sheet Description Features The HDSP-31xx-51xx Series of displays incorporates a new slim font character design. This slim font features narrow width, specially mitered segments to give a fuller appearance to the illuminated character. Faces of these displays are painted a neutral gray for enhanced on/off contrast. * Excellent appearance All devices are available in either common anode or common cathode configuration with right hand decimal point. Low current versions are available in either AlGaAs red or HER. * Choice of colors: DH AlGaAs red, High Efficiency Red (HER), yellow, and green * Slim font design * Mitered corners, evenly illuminated segments * Gray face for optimum on/off contrast * Low current available, AlGaAs red and HER choice of character size: 10 mm and 13 mm * 50 viewing angle * Characterized for luminous intensity Devices AlGaAs Red Low Current HDSP- HER Std. Current HDSP- HER Low Current HDSP- Yellow Std. Current HDSP- Green Std. Current HDSPDescription Package Drawing 315H 315E 315L 315Y 315G Common Anode, 10 mm Display A 316H 316E 316L 316Y 316G Common Cathode, 10 mm Display B 515H 515E 515L 515Y 515G Common Anode, 13 mm Display A 516H 516E 516L 516Y 516G Common Cathode, 13 mm Display B Part Numbering System 5082 - X X X X - X X X X X HDSP - X X X X - X X X X X Mechanical Options[1] 00: No Mechanical Option Color Bin Options[1,2] 0: No Color Bin Limitation Maximum Intensity Bin[1,2] 0: No Maximum Intensity Bin Limitation Minimum Intensity Bin[1,2] 0: No Minimum Intensity Bin Limitation Device Configuration/Color[1] H: AlGaAs Red E: High Efficiency Red G: Green Y: Yellow Device Specific Configuration[1] Refer to Respective Datasheet Package[1] Refer to Respective Datasheet Notes: 1. For codes not listed in the figure above, please refer to the respective datasheet or contact your nearest Avago representative for details. 2. Bin options refer to shippable bins for a part number. Color and Intensity Bins are typically restricted to 1 bin per tube (exceptions may apply). Please refer to respective datasheet for specific bin limit information. 2 HDSP-315x/316x Series 6 COLOR BIN (NOTE 3) 0.9 2.54 0.38 10 HDSP-XXXX HP XYY ZW 10 LUMINOUS INTENSITY CATEGORY 12.8 0.2 DIA. 1.2 4 x 2.54 0.53 0.05 6.4 0.1 7 0.1 9.7 0.1 1 2 f 3 4 5 e a g d 10 9 b 8 7 c 6 DP PIN FUNCTION 1 g 2 f 3 Common A/C 4 e 5 d 6 DP 7 c 8 Common A/C 9 b 10 a DATE CODE 10.4 MIN. 0.3 0.05 7.62 0.38 HDSP-515x/516x Series HDSP-315X pkg dimen. (A) LUMINOUS INTENSITY CATEGORY 7.40 10 COLOR BIN (NOTE 3) 5.08 12.25 0.15 17.50 + 0.3 - 0.1 DIA. 1.25 HDSP-XXXX HP XYY ZW 13.0 DATE CODE 6.40 0.1 7.00 0.1 1.04 0.3 TYP. 2.54 0.3 TYP. Notes: 1. Package dimensions in millimeters. 2. Untoleranced dimensions are for reference only. HDSP-315X pkg dimen. (B) 3. For yellow and green devices only. 3 a f e d 0.29 0.08 TYP. b g 15.24 0.3 3.60 0.3 0.38 0.08 10 9 8 7 6 2.54 0.38 1.25 c DP 1 2 3 4 5 PIN FUNCTION 1 e 2 d 3 Common A/C 4 c 5 DP 6 b 7 a 8 Common A/C 9 f 10 g Absolute Maximum Ratings AlGaAs Red Low Current HER HER Low Current Yellow Green Units Average Power per Segment or DP 37 105 52 105 105 mW Peak Forward Current per Segment or DP 45 90[2] 45 90[5] 90[7] mA DC Forward Current per Segment or DP 15[1] 30[3] 15[4] 30[6] 30[8] mA Operating Temperature Range -20 to 100 Description -40 to +100 C Storage Temperature Range -40 to +100 C Reverse Voltage per Segment or DP 3.0 V Wavesoldering Temperature for 3 seconds 1.59 mm below body 250 C Notes: 1. Derate above 91C at 0.53 mA/C. 2. See Figure 9 to establish pulsed conditions. 3. Derate above 53C at 0.45 mA/C. 4. Derate above 80C at 0.38 mA/C. 5. See Figure 10 to establish pulsed conditions. 6. Derate above 81C at 0.52 mA/C. 7. See Figure 11 to establish pulsed ocnditions. 8. Derate above 39C at 0.37 mA/C. Electrical/Optical Characteristics at TA = 25C AlGaAs Red Low Current Device Series HDSPParameter Symbol Min. Typ. Max. Units 315/316H 515/516H Luminous Intensity/Segment[1,2] (Digit Average) IV 180 650 cd IF = 1 mA V IF = 1 mA Forward Voltage/Segment or DP VF 1.8 Peak Wavelength PEAK 645 nm Dominant Wavelength[3] d 637 nm Reverse Voltage/Segment or DP[4] VR 15 V Thermal Resistance LED Junction-to-Pin RJ-PIN 255 C/W/Seg 3 2.2 Test Conditions IR = 100 A HER Device Series HDSPParameter Symbol Min. Typ. Max. Units 315/316E 515/516E Luminous Intensity/Segment[1,2] (Digit Average) IV Forward Voltage/Segment or DP Test Conditions 2600 cd IF = 10 mA VF 1.9 V IF = 10 mA Peak Wavelength PEAK 635 Dominant Wavelength[3] d 626 nm Reverse Voltage/Segment or DP[4] VR 30 V Thermal Resistance LED Junction-to-Pin RJ-PIN 200 C/W/Seg 4 450 3 2.5 nm IR = 100 A HER Low Current Device Series HDSPParameter Symbol Min. Typ. Max. Units 315/316L 515/516L Luminous Intensity/Segment[1,2] (Digit Average) IV Forward Voltage/Segment or DP Peak Wavelength Dominant Wavelength[3] Reverse Voltage/Segment or DP[4] Thermal Resistance LED Junction-to-Pin RJ-PIN Test Conditions 370 cd IF = 2 mA VF 2.1 V IF = 2 mA PEAK 635 nm d 626 nm VR 30 V 200 C/W/Seg 180 3 2.5 IR = 100 A Yellow Device Series HDSPParameter Symbol Min. Typ. Max. Units 315/316Y 515/516Y Luminous Intensity/Segment[1,2] (Digit Average) IV Forward Voltage/Segment or DP Peak Wavelength Test Conditions 1800 cd IF = 10 mA VF 2.0 V IF = 10 mA PEAK 583 nm Dominant Wavelength[3] d 586 nm Reverse Voltage/Segment or DP[4] VR 50 V Thermal Resistance LED Junction-to-Pin RJ-PIN 200 C/W/Seg 450 3 2.5 IR = 100 A Green Device Series HDSPParameter Symbol Min. Typ. Max. Units 315/316G 515/516G Luminous Intensity/Segment[1,2] (Digit Average) IV Forward Voltage/Segment or DP VF Peak Wavelength PEAK 566 nm Dominant Wavelength[3] d 571 nm Reverse Voltage/Segment or DP[4] VR 50 V Thermal Resistance LED Junction-to-Pin RJ-PIN 200 C/W/Seg 450 3 Test Conditions 5000 cd IF = 10 mA 2.1 V IF = 10 mA 2.5 IR = 100 A Notes: 1. Case temperature of device immediately prior to the intensity measurement is 25C. 2. The digits are categorized for luminous intensity. The intensity category is designated by a letter on the side of the package. 3. The dominant wavelength, is derived from the CIE chromaticity diagram and is that single wavelength which defines the color of the device. 4. Typical specification for reference only. Do not exceed absolute maximum ratings. 5 50.0 20 18 16 14 12 10 8 6 4 2 0 20.0 RJ-A = 770C/W IF - FORWARD CURRENT PER SEGMENT - mA IF AVE. MAX - MAXIMUM AVERAGE FORWARD CURRENT PER SEGMENT - mA AlGaAs Low Current 20 30 40 50 60 70 80 90 100 110 120 TA - AMBIENT TEMPERATURE - C 20 RELATICE LUMINOUS INTENSITY (NORMALIZED TO 1AT 1ma) 2.0 1.0 0.5 0.1 Figure 1. Maximum allowable average or DC current vs. ambient temperature. 10 5 2 1 0.5 0.2 0.1 0.1 0.2 1 2 5 10 0.5 IF - FORWARD CURRENT PER SEGMENT - mA Figure 3. Relative luminous intensity vs DC forward current. 6 10.0 5.0 20 0 0.5 1.0 1.5 VF - FORWARD VOLTAGE - V Figure 2. Forward current vs. forward voltage. 2.0 2.5 HER, Yellow, and Green 10 10000 OPERATION IN THIS REGION REQUIRES TEMPERATURE DERATING OF IDC MAXIMUM 10 1 10 z 0H 30 Hz 1K Hz 3K Z KH 10 IFPEAK RATIO OF MAXIMUM OPERATING IDC MAX PEAK CURRENT TO TEMPERATURE DERATED DC CURRENT 100 0H z DC OPERATION 10 100 1000 10000 tp - PULSE DURATION - s Figure 6. Allowable peak current vs. pulse duration - Green. 100 80 60 YELLOW 40 HER 20 0 GREEN 2.0 3.0 4.0 VF - FORWARD VOLTAGE - V Figure 8. Forward current vs. forward voltage characteristics. 7 0 1.0 1 z 10 100 1000 tp - PULSE DURATION - s 50 45 40 35 30 25 20 15 10 10000 DC OPERATION 5.0 5 0 R J-A = 770C/W GREEN HER YELLOW 50 60 70 80 90 100 110 120 TA - AMBIENT TEMPERATURE - C Figure 7. Maximum allowable DC current per segment as a function of ambient temperature. RELATIVE LUMINOUS INTENSITY (NORMALIZED TO 1 AT 5 mA FOR HER AND YELLOW AND TO 1 AT 10 mA FOR GREEN) IF - FORWARD CURRENT PER SEGMENT - mA 1 1 0H Figure 5. Maximum tolerable peak current vs. pulse duration - Yellow. Figure 4. Maximum tolerable peak current vs. pulse duration - HER. IDC MAX - MAXIMUM DC CURRENT PER SEGMENT - mA 10 100 1000 tp - PULSE DURATION - s DC OPERATION 10 z 0H 30 Hz 1K Hz HZ z 10 3K 0H OPERATION IN THIS REGION REQUIRES TEMPERATURE DERATING OF IDC MAXIMUM K 10 Z 1 z 0H 30 Hz 1K Hz 3K KH 1 10 100 IFPEAK RATIO OF MAXIMUM OPERATING IDC MAX PEAK CURRENT TO TEMPERATURE DERATED DC CURRENT OPERATION IN THIS REGION REQUIRES TEMPERATURE DERATING OF IDC MAXIMUM 10 IFPEAK RATIO OF MAXIMUM OPERATING IDC MAX PEAK CURRENT TO TEMPERATURE DERATED DC CURRENT 100 20 30 40 12 10 HER 8 YELLOW 6 4 GREEN 2 0 0 15 5 10 20 25 IF - FORWARD CURRENT PER SEGMENT - mA Figure 9. Relative luminous intensity vs. DC forward current. 30 20 18 16 14 12 10 8 6 4 2 0 20 RJ-A = 770C/W HER 30 40 50 60 70 80 90 100 110 120 TA - AMBIENT TEMPERATURE - C RELATIVE LUMINOUS INTENSITY (NORMALIZED TO 1 AT 2 mA FOR HER AND TO 1 AT 4 mA FOR YELLOW AND GREEN 16 14 12 HER 8 6 4 2 0 0 2 4 6 8 10 12 14 VF - FORWARD CURRENT PER SEGMENT - mA Figure 12. Relative luminous intensity vs. DC forward current. 8 50 40 30 20 HER 10 0 0 0.5 1.0 1.5 2.0 VF - FORWARD VOLTAGE - V Figure 11. Forward current vs. forward voltage. Figure 10. Maximum allowable average or DC current vs. ambient temperature. 10 IF - FORWARD CURRENT PER SEGMENT - mA IF AVE. MAX - MAXIMUM AVERAGE FORWARD CURRENT PER SEGMENT - mA HER Low Current 16 2.5 3.0 Intensity Bin Limits (mcd) HER Low Current, AlGaAs Red Low Current IV Bin Category Color Categories HDSP-31xL/H, HDSP-51xL/H Min. Max. Dominant Wavelength (nm) Color Bin Min. Max. Yellow E 0.180 0.360 1 581.50 585.00 F 0.280 0.560 3 584.00 587.50 G 0.450 0.900 2 586.50 590.00 H 0.700 1.400 4 589.00 592.50 I 1.100 2.200 2 573.00 577.00 K 1.800 3.600 3 570.00 574.00 L 2.800 5.600 4 567.00 571.00 M 4.500 9.000 5 564.00 568.00 N 7.000 15.000 Green Note: All categories are established for classification of products. Products may not be available in all categories. Please contact your local Avago representatives for further clarification/information. HER Std. Current, Green Std. Current, Yellow Std. Current IV Bin Category HDSP-31xE/G/Y, HDSP-51xE/G/Y Min. Max. G 0.450 0.900 H 0.700 1.400 I 1.100 2.200 K 1.800 3.600 L 2.800 5.600 M 4.500 9.000 N 7.000 15.000 Electrical/Optical Soldering/Cleaning For more information on electrical/optical characteristics, please see Application Note 1005. Cleaning agents from the ketone family (acetone, methyl ethyl ketone, etc.) and from the chlorinated hydrocarbon family (methylene chloride, trichloroethylene, carbon tetrachloride, etc.) are not recommended for cleaning LED parts. All of these various solvents attack or dissolve the encapsulating epoxies used to form the package of plastic LED parts. Contrast Enhancement For information on contrast enhancement, please see Application Note 1015. For further information on soldering LEDs, please refer to Application Note 1027. For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright (c) 2005-2011 Avago Technologies. All rights reserved. Obsoletes 5989-2640EN AV02-1769EN - March 28, 2011